Accessories and workbenches

Transcription

1 Permanent contact The permanent-contact follows the movements of the body and enables the natural stressing and relieving of different muscle and spinal areas. Synchronous mechanism The user-friendly synchronous and "similar" mechanism promotes the shifting between different sitting postures. The seat and the back rest track the movements of the body in synchronous fashion, the mechanism provides continuous adjustment to body weight. Requirements laid down in the DIN This standard defines partially with close reference to DIN 1335 how a chair must be constructed for fabrication work, in order that it will fulfil all safety technology and ergonomic requirements: The work chair may not exhibit any places where there is danger of hands becoming stuck or crushed. All possibility of inadvertent changes to the chair adjustment while the chair is being used must be excluded. The must be pendularmounted, and adjustable in both height and angle. If the lowest setting of the seat height is less than 500 mm, then a depth springing is required for cushioning the impact of sitting down. The base frame must have at least five points of support. A slip-resistant climbing aid is required for chairs which have seats whose heights can be adjusted to more than 650 mm; in addition, no castors are permitted. Elabo Factory and Cleanroom swivel chairs meet this standards in all of its points. Requirements laid down in the DIN 1335 DIN EN 1335 replaces DIN 4551 of 1988 and is valid for office work chairs. Part 1 of the standard defines essential minimum and maximum values which an ergonomic work chair must fulfil. Among other things, the standard contains requirements regarding seat height, seat depth, seat width, seat surface tilt, the height of the, the width of the, the range of adjustment of the tilt, and the position, width and length of arm supports. Part 2 of the standard prescribes the safety requirements for office work chairs. Requirements are defined with respect to design for the avoidance of places where crushing, sticking and shearing could take place as well as criteria for determining structural stability, resistance to rolling and sturdiness. The Elabo office and laboratory swivel chairs in the Basic and Highline series and the 24 h swivel chairs always keep to this standard. Suitability for 24 h operation The use of work station chairs in control rooms places high demands on the material quality and the wearresistance of the cover fabric and the mechanisms. Elabo chairs for 24 h operation have been designed to cope with these loads, and are appropriately certified. Suitability for ESD protection zones IEC Reliable ESD protection is ensured by means of comfortable conductive cushions, conductive castors and a dissipation resistance in the range of Ohm, which enables a controlled dissipation of electrostatic charges. Elabo LaboratorySystems L 189

2 Basic4 Medium-high Swivel chair with permanent contact Continuously adjustable height setting from mm through safety gas spring Backrest with integrated lumbar support, height adjustment of up to 60 mm Continuously adjustable weight regulation to a body weight of 45 and 120 kg Five-spoke base frame with double swivel castors, either for hard or soft floors, Armrests available as an option 450 mm 410 mm Castors S1-1W S1-1X S1-1S S1-1T S1-1C S1-1D Basic6 High Swivel chair with synchronous mechanism Equipped as Basic4, but Synchronous mechanism with an opening angle between the seat and the of up to a maximum of 125 degrees Armrests available as an option 530 mm Castors S1-4W S1-4X S1-4S S1-4T S1-4C S1-4D Elabo LaboratorySystems L 190

3 Basic4 ESD Medium-high ESD swivel chair with permanent contact Conductive seat and back pads Continuously adjustable height setting from mm through safety gas spring Backrest with integrated lumbar support, height adjustment of up to 60 mm Continuously adjustable weight regulation to a body weight of 45 and 120 kg Aluminium five-spoke base frame with conductive double swivel castors, either for hard or soft floors, 450 mm 410 mm Castors hard, for soft floors hard, for soft floors hard, for soft floors S1-2C S1-2D S1-2Q S1-2R S1-2W S1-2X Basic6 ESD High ESD swivel chair with synchronous mechanism Equipped as Basic4 ESD, but Synchronous mechanism with an opening angle between the seat and the of up to a maximum of 125 degrees 530 mm Castors S1-5C S1-5D S1-5Q S1-5R S1-5W S1-5X Elabo LaboratorySystems L 191

4 Basic 4/6 armrests Ring armrests made of plastic, suitable for Basic 4/6 swivel chairs, can be retrofitted S1-6C Basic 8/10 armrests Armrests made of plastic, width and height-adjustable suitable for Basic 8/10 swivel chairs, can be retrofitted S6-6A Basic Conference chair 4-legged conference chair Stackable visitor chair with a completely fabric-covered, four-foot base made of powder coated steel pipe with felt slides for hard floors, pipe diameter 25 mm, alternately available with armrests. Backrest width: 450 mm 460 mm 460 mm 440 mm 470 mm Armrests yes no yes no yes no Order no.s1-8x S1-8W S1-8T S1-8S S1-8D S1-8C Elabo LaboratorySystems L 192

5 Basic8 Medium-high High quality swivel chair with synchronous mechanism Continuously adjustable height setting from mm through safety gas spring Backrest with an adjustment range of 7 positions (70 mm) Variable basic setting for seat height (30 mm downward and 20 mm upward) Continuously adjustable weight regulation to a body weight of 45 and 130 kg Synchronous mechanism, opening angle between the seat and the up to max Five-spoke base frame with double swivel castors, either for hard or soft floors, 460 mm mm Castors S6-1W S6-1X mottled S6-3W mottled S6-3X S6-1C S6-1D mottled S6-3C mottled S6-3D also available in ESD design Basic10 High High quality swivel chair with synchronous mechanism Equipped as Basic8, but with higher 470 mm mm 530 mm Castors S6-4W S6-4X mottled S6-7W mottled S6-7X S6-4C S6-4D mottled S6-7C mottled S6-7D also available in ESD design Elabo LaboratorySystems L 193

6 Clean16 Cleanroom ESD swivel chair Ergonomically formed cushion parts with foam-injection technology with air-tight seals, conductive ESD artificial leather upholstery, seat support and cover made of powder coated steel sheeting. Smooth, enclosed surfaces for the prevention of particle deposits, seat height adjustment with safety gas spring, permanent contact, height adjustment, encapsulated mechanism, five-foot base frame made of polished aluminium with conductive castors. Certified for clean-room use by the Fraunhofer-Institut IPA Stuttgart (suitable for Clean Room Class 1) Artificial leather Metal parts Swivel chair ESD Clean mm 480 mm 470 mm 380 mm S3-6A LuPo This chair is recommended by the Federal Association of German Back Exercise Schools. Air-cushioned swivel chair with swivel castors Seat base is made of PP with double-wall structure. The air cushion effect also applies. 3-D rocker mechanism towards the front, to the side and to the rear. Hard castors for soft floors. Colour of metallic parts arctic, mm; 440 mm; 460 mm dark red -grey dark green dolphin grey yellow-orange S4-1R S4-1S S4-1T S4-1U S4-1V S4-1W Factory standing aid Factory standing aid Optimum freedom of movement due to the leaning surfaces being rotatable by 360, made of integral foam with integrated carrying handle. height adjustment with gas spring lift, stable plate base mm Incline adjustment forward: 10 Factory standing aid, standard Factory standing aid, ESD S3-4A S3-5A Elabo LaboratorySystems L 194

7 Factory4 Factory4 swivel chair Seat and s aligned to your body's anatomy, made of impact and breakage-resistant plastic, easy-clean surfaces, resistant to lyes and acids, seat height adjustment with safety gas spring, rounded seat front edge to lessen pressure on legs, permanent contact, integrated lumbar support, continuously adjustable height adjustment, incline adjustment, reduced width, five-spoke base frame, either with sliders or rollers. basalt grey mm 480 mm 420 mm With castors With sliders S3-1A S3-1E Factory8 Factory8 swivel chair with climbing aid Equipped as Factory4, but extended seat height, climbing aid with climbing aid and sliders: basalt grey mm 480 mm 420 mm S3-1K Luxury replaceable pad Simple and easy hook-in installation; can be replaced or retrofitted at any time Textile pad, soft and breathable, with resistant cover fabric Integral foam pad for soft, 'air-cushioned sitting', washable, resistant to mild acids and lyes, structured surface for improved climatic comfort. S3-1Q S3-1R S3-2U S3-1V Elabo LaboratorySystems L 195

8 Factory4 ESD Factory4 ESD-swivel chair Seat and s aligned to your body's anatomy and volume conductive, made of impact and breakage-resistant plastic, easyclean surfaces, resistant to lyes and acids, seat height adjustment with safety gas spring, rounded seat front edge to lessen pressure on legs, permanent contact, integrated lumbar support, continuously adjustable height adjustment, incline adjustment, reduced width, five-spoke base frame, either with sliders or castors. Dissipation resistance pursuant to IEC : Ohm Surface resistance (IEC ): 10 5 Ohm mm; 480 mm; 420 mm With ESD castors With ESD sliders S3-2A S3-2E Factory8 ESD Factory8 ESD swivel chair with climbing aid Equipped as Factory4 ESD, but extended seat height, climbing aid mm; 480 mm; 420 mm with climbing aid and ESD sliders: S3-2K ESD pad Luxury ESD replaceable pads Simple and easy hook-in installation; can be replaced or retrofitted at any time Conductive textile pad, soft and breathable, with resistant cover fabric Conductive integral foam pad for soft, 'air-cushioned sitting', washable, resistant to mild acids and lyes, structured surface for improved climatic comfort. S3-2Q S3-2U Elabo LaboratorySystems L 196