TABLE WITH CYLINDER BASE INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "TABLE WITH CYLINDER BASE INSTALLATION INSTRUCTIONS"

Aubrey Cory Daniel
6 years ago
Views:

1 TABLE WITH CYLINDER BASE TABLE OF CONTENTS Round Table with Cylinder Base Side 2 One Piece Conference Table with Cylinder Base Side 3 Two Piece Conference Table with Cylinder Base Side 4 SIDE 1 OF 5 (7/03)

2 ROUND TABLE WITH CYLINDER BASE Illustration 1 Bottom of cylinder Positioning template Evenly distribute six 20 lbs (9.07 kg) bags of sand inside cylinder table top Cylinder 120 lbs (54 kg) of clean dry sand ¼" power nutdriver Drill (1) Table top (1) Cylinder (6) Sand bag (6) (5) Wood products are heavier then they appear and may be hard to control when moving. Use two or more people when moving wood products or severe personal injury may result. Heavy panels can pinch or crush fingers. Do not place fingers between or under panels during assembly. Table can become unstable and tip over resulting in severe injury to yourself or others. To inhibit tipping, evenly distribute 120 lbs (54 kg) of clean dry sand inside each cylinder before attaching table top. To prevent the possibility of serious eye injury, always wear eye protection when using power tools. 1. Refer to Illustration 1. Lay cylinder upside down. 2. Refer to Illustration 1. Locate threaded s on bottom of cylinder. Thread a leveling (from hardware pack) into each threaded by turning leveling s clockwise until leveling s are flat against cylinder. 3. Set cylinder upright and position cylinder s where table will be used. 4. Measure 12" (30.5 cm) from bottom of sand bags and mark bags with a felt tip pen. Fill sand bags to mark with 20 lbs (9 kg) of clean dry sand and tie bags closed. 5. Refer to Illustration 1. Evenly distribute six 20 lbs (9 kg) bags of clean dry sand inside cylinder. 6. Refer to. Use two or more people to position table top onto cylinder as shown. Align cylinder to center of table top using template attached to bottom of table top. 7. Refer to. Use the ¼" power nutdriver to install six s (from hardware pack) through cylinder and into table top. 8. Adjust leveling s until table is level. SIDE 2 OF 5 (7/03)

3 CONFERENCE TABLE WITH CYLINDER BASE Illustration 1 Table Top cylinder Illustration 4 Cylinder 1 1 /2" Cylinder Base Illustration 3 table top Glide Evenly distribute six 20 lbs (9.07 kg) bags of sand inside cylinder Positioning template 240 lbs (109 kg) of clean dry sand 1 /4" Power nutdriver Drill (1) Table top (2) Cylinder (12) Sand bag (12) (10) Wood products are heavier then they appear and may be hard to control when moving. Use two or more people when moving wood products or severe personal injury may result. Heavy panels can pinch or crush fingers. Do not place fingers between or under panels during assembly. Table can become unstable and tip over resulting in severe injury to yourself or others. To inhibit tipping, evenly distribute 120 lbs (54 kg) of clean dry sand inside each cylinder before attaching table top. To prevent the possibility of serious eye injury, always wear eye protection when using power tools. 1. Refer to. Lay each cylinder upside down. 2. Refer to. Locate threaded s on bottom of each cylinder. Thread a leveling (from hardware pack) into each threaded by turning leveling s clockwise until leveling s are flat against cylinder. 3. Set each cylinder upright and position cylinder s where table will be used. 4. Measure 12" (30.5 cm) from bottom of sand bags and mark bags with a felt tip pen. Fill sand bags to mark with 20 lbs (9 kg) of clean dry sand and tie bags closed. 5. Refer to Illustration 3. Evenly distribute six 20 lbs (9 kg) bags of clean dry sand inside each cylinder. 6. Refer to Illustration 4. Use two or more people to position table top onto cylinder s as shown. Align cylinder s with positioning templates attached to table top bottom. 7. Refer to Illustration 4. Use the 1 /4" power nutdriver to install six s (from hardware pack) through each cylinder and into table top. 8. Adjust leveling s until table is level. SIDE 3 OF 5 (7/03)

4 Illustration 1 cylinder Illustration 4 Positioning template End cylinder CONFERENCE TABLE WITH CYLINDER BASE Table Top Half 1 1 /2" Support Bracket Glide Cylinder Base Illustration 3 Center cylinder 7 /8" Connector Bracket Evenly distribute six 20 lb (9 kg) bags of sand inside cylinder table top half 360 lbs (162 kg) of clean dry sand 1 /4" Power nutdriver Drill (2) Table top half (3) Cylinder (2) Connector Bracket (8) 7 /8" screw (2) Support bracket (15) (15) (18) Sand bag Wood products are heavier then they appear and may be hard to control when moving. Use two or more people when moving wood products or severe personal injury may result. Heavy panels can pinch or crush fingers. Do not place fingers between or under panels during assembly. Table can become unstable and tip over resulting in severe injury to yourself or others. To inhibit tipping, evenly distribute 120 lbs (54 kg) of clean dry sand inside each cylinder before attaching table top. To prevent the possibility of serious eye injury, always wear eye protection when using power tools. 1. Refer to. Lay each cylinder upside down. 2. Refer to. Locate threaded s on bottom of each cylinder. Thread a leveling (from hardware pack) into each threaded by turning leveling s clockwise until leveling s are flat against cylinder. 3. Set each cylinder upright and position cylinder s where table will be used. 4. Measure 12" (30.5 cm) from bottom of sand bags and mark bags with a felt tip pen. Fill sand bags to mark with 20 lbs (9 kg) of clean dry sand and tie bags closed. 5. Refer to Illustration 3. Evenly distribute six 20 lbs (9 kg) bags of clean dry sand inside each cylinder. 6. Refer to Illustration 4. Use two or more people to position a table top half onto cylinder s as shown. Align cylinder s with positioning templates attached to table top bottom. SIDE 4 OF 5 (7/03)

5 CONFERENCE TABLE WITH CYLINDER BASE Illustration 5 7. Refer to Illustration 4. Align center cylinder against positioning template. Illustration 6 Cut-out Cylinder Table top halves Table top halves Remaining cylinder Connector bracket Support bracket 7 /8" screw 8. Refer to Illustration 4. Use the 1 /4" power nutdriver to install six s (from hardware pack) through end cylinder and into table top. Install three s (from hardware pack) through center cylinder and into table top. 9. Refer to Illustration 5. Use two or more people to position the remaining table top half onto cylinder s as shown. 10. Refer to Illustration 5. Insert connector brackets into cutouts in bottom of table top halves. Ensure edges of table top halves are aligned and use the adjustable wrench to fully tighten connector brackets. 11. Refer to Illustration 6. Position support brackets over seam of table top halves and align holes in support bracket with pre-drilled holes in bottom of table top halves. 12. Refer to Illustration 6. Use the drill and 1 /4" power nutdriver to install four 7 /8" screws (from hardware pack) through holes in each support bracket and into pre-drilled holes in table top halves. Fully tighten screws. 13. Refer to Illustration 6. Align remaining end cylinder with positioning template attached to table top bottom. 14. Refer to Illustration 6. Use the 1 /4" power nutdriver to install six s (from hardware pack) through remaining cylinder and into table top. 15. Adjust leveling s until table is level. SIDE 5 OF 5 (7/03)

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM S2000 AII 26324 Issue Date OCT 2004 PARTS LIST Headrest Speaker System P/N 08A54-S2A-100 3 Small wire ties 2 Headrest speakers 9