PLASTIC FOLDING ARM KIT This kit is designed for the 1600 model barrier gate operators only. Recommended for low headroom applications.
|
|
- Harold Park
- 6 years ago
- Views:
Transcription
1 PLASTIC FOLDING ARM KIT This kit is designed for the 600 model barrier gate operators only. Recommended for low headroom applications. Kit Includes: Plastic Arms Attachment Assembly Clamp Locking Turnbuckle Eyelet (Connected) Locking Eye Bolt Arm Hinge 8 Self Tapping Screws Installation Cut Arms to Length Note: Completed folding arm assembly shown in the UP position to illustrate the total height. Cut this arm first for the height limitations. Determining First Arm Length Total Height Note: Completed folding arm assembly shown in the DOWN position to illustrate Cut this arm second for the Note: Second arm can be a different size than the first. Determining Second Arm Length Traffic Lane Width
2 Installing Arms Existing Stud Top View of Hub Adjust to clear hub. Remove stud from operator housing and assemble as shown. Bolt Head (Inside Housing) Washer (Inside Housing) 3 Install cable. MUST clear hub! Install eye bolt into arm hinge with vise-grips. Attach arm hinge to inner arm with 4 self-tapping screws. Install inner arm on hub. Cut off excess cable. Clamp Eyelet MUST be installed in turnbuckle. Allow turnbuckle to loosen or tighten. 4 Install outer arm with 4 self-tapping screws. Adjusting and Locking Assembly After adjusting cable tension, lock turnbuckle with nuts to keep turnbuckle from twisting. Lock eye bolt with nut to keep eye bolt from twisting. Inner Arm Side View of Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely. Important: Do not adjust cable too tight or it will bind C-5-08 Copyright 008 DoorKing, Inc. All rights reserved.
3 cause vehicle damage, serious injury or death. at all times. Bicycles Motorcycles cause vehicle damage, serious injury or death. at all times. Bicycles Motorcycles WOOD FOLDING ARM KIT This kit is designed for the 600 model barrier gate operators only. Recommended for low headroom applications. WARNING Kit Includes: MOVING ARM can STAY CLEAR of arm 4 Bolts with Bolt with Bolt with Brass NO: Pedestrians Attachment Assembly s (Small) and (Medium) and (Large) Clamp Wood Arms Eyelet Locking Turnbuckle WARNING MOVING ARM can STAY CLEAR of arm NO: Pedestrians Hinge Plates Installation Cut Arms to Length Note: Completed folding arm assembly shown in the UP position to illustrate the total height. Cut this arm first for the height limitations. Determining First Arm Length Total Height Note: Completed folding arm assembly shown in the DOWN position to illustrate Cut this arm second for the Note: Second arm can be a different size than the first. Determining Second Arm Length Traffic Lane Width
4 cause vehicle damage, serious injury or death. at all times. Bicycles Motorcycles Installing Attachment Assembly Adjust to clear hub. Remove stud from operator housing and assemble as shown. Bolt Head (Inside Housing) Washer (Inside Housing) Installing Arms Inner Arm Turnbuckle Installing Hinge Plates Bolt (Medium) Bolt (Large) Existing Stud WARNING 4 Bolts (Small) MOVING ARM can cause vehicle damage, serious injury or death. STAY CLEAR of arm at all times. NO: Pedestrians Bicycles Motorcycles Top View of A Brass 4 s Hub Install inner arm on hub. 3 Install cable. MUST clear hub! Cut off excess cable. Clamp Eyelet MUST be installed in turnbuckle. A Install hinge plates. Allow turnbuckle to loosen or tighten. Adjusting and Locking Assembly After adjusting cable tension, lock turnbuckle with nuts in position shown to prevent turnbuckle from rubbing against hinge plates when the arm is in the UP position. WARNING MOVING ARM can STAY CLEAR of arm NO: Pedestrians Inner Arm Side View of Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely. Important: Do not adjust cable too tight or it will bind D-5-08 Copyright 008 DoorKing, Inc. All rights reserved.
5 MODEL 60 FAN KIT This kit is designed for the 600 model barrier gate operators only. Recommended for hot and humid climates. An automatic thermostat will control heat and humidity inside operator housing. Kit Includes: Fan Assembly with black and white wires, 5 wire ties, 3 double stick wire tie mounts, plastic wire restrainers and 3 nylon lock nuts. Threaded Housing Studs (Existing) Installation Shut off ALL power to operator Turn off the DC convenience open power switch on certain operator models FIRST then shut off the AC input power to the operator from the circuit breaker. Lock Nut Lock Nut Lock Nut Mounting Tab 3 Route fan wires as shown. Use supplied wire stays and existing wire restrainers. Keep wires clear of all moving parts. Mount fan using 3 existing threaded studs and lock nuts supplied. Slide mounting tabs over existing air duct. Mounting Tab Existing Air Duct Threaded Air Duct Stud (Existing) Existing Wire Restrainers 4 Exhaust Vents 4 Connect the fan power wires according to operator model type. Neutral Hot DANGER HIGH VOLTAGE! Neutral Neutral 5 VAC Hot VAC Models 30 VAC/460 VAC Models B-5- Wire Stays Existing Air Duct Air Flow Intake Vents Keep intake vents clear of debris. Copyright 0 DoorKing, Inc. All rights reserved. 5 Fan switch settings. OFF - Turns the fan off. ON - Turns the fan on continuously. AUTO - Normal setting. Automatically turns the fan ON when the temperature rises above 90 F inside the housing, and turns the fan OFF when the temperature drops below 90 F.
6 600 5 VAC AMP HEATER KIT This kit is designed for the 600 model barrier gate operators only. For cold weather climates where temperatures routinely drop below 40 F (4 C). A built-in thermostat will automatically control the temperature inside operator housing. High Voltage AC Input Power for the 600 Barrier Gate Operator with a Heater DO NOT use the high voltage wire size and distance requirements table in the Installation/Owner s manuals to determine the high voltage AC input power wire size and distance requirements for the barrier gate operator because of a much greater current draw when using the heater. Use the table below to determine the wire size and distances for your chosen barrier gate operator when a heater is installed. EACH operator should have a Dedicated circuit breaker at the power source. If the high voltage AC input power wiring is greater than the maximum distance shown, it is recommended that a service feeder be installed. When large gauge wire is used, a separate junction box must be installed for the operator connection. Wire run distances are based on NEC guidelines for copper wire allowing a maximum 3% voltage drop on the line. The calculated distance was then further reduced by 0% to allow for other loses in the system. Never run low voltage rated wire insulation in the same conduit as high voltage rated wire insulation. High voltage AC input wire size and distance requirements for a 600 with a heater. Operator and Wire Size / Distance in Feet Model Horsepower Volts Heater Amps AWG 0 AWG 8 AWG 6 AWG / HP HP In bi-parting (dual) barrier gate applications, high voltage AC input power is required for EACH 600 operator with heater.
7 Installation of Heater Kit Includes: Heater / mounting plate, locknuts, 5 wire ties, 3 double stick wire tie mounts, and plastic wire restrainers. 3 Shut off ALL power to operator. Turn off the DC convenience open power switch on certain operator models first then shut off the AC input power to the operator from the circuit breaker. Route heater wires as shown. Use supplied wire stays and existing wire restrainers. Keep wires clear of all moving parts and the heater vents. Mount Heater Locate existing threaded studs in operator. Heater MUST be mounted on mounting plate. Place the supplied washers between the operator wall and the mounting plate to create an air gap. CAUTION: Heat will be transferred to the outside wall of the operator if NO air gap exists between the heater and the inside wall of the operator. Washer Mounting Plate Operator Threaded Stud (Existing) Operator Threaded Stud (Existing) Washer Existing Wire Restrainers 4 Air Gap 4 Power Connection Connect the heater power wires according to operator AC power type. Neutral Hot DANGER HIGH VOLTAGE! Neutral 5 VAC Hot DANGER HOT! VAC Models 30 VAC/460 VAC Models Heater Switch AUTO - Normal setting. Automatically turns the heater ON when the temperature drops below 40 F inside the operator, and turns the heater OFF when the temperature rises above 40 F inside the operator. OFF - Turns the heater off. Wire Stays ON - Turns the heater on continuously. The heater will become VERY HOT when running continuously G-7- Copyright 0 DoorKing, Inc. All rights reserved.
8 ALUMINUM ARM FOLDING KIT This kit is designed for the 600 model barrier gate operators only. Recommended for low headroom applications. Kit Includes: Attachment Assembly Aluminum Arms with End Caps Clamp Eyelet Locking Turnbuckle (Connected) Locking Eye Bolt Arm Hinge 8 Self Tapping Screws Installation Cut Arms to Length Note: Completed folding arm assembly shown in the UP position to illustrate the total height. Cut this arm first for the height limitations. Determining First Arm Length Total Height Note: Completed folding arm assembly shown in the DOWN position to illustrate Cut this arm second for the Note: Second arm can be a different length than the first. Determining Second Arm Length Traffic Lane Width
9 Installing Arms Existing Stud Top View of Adjust to clear hub. Remove stud from operator housing and assemble as shown. Bolt Head (Inside Housing) Washer (Inside Housing) Install eye bolt into arm hinge with vise-grips. Attach arm hinge to arm with 4 self-tapping screws. Hub 3 Install cable. MUST clear hub! Install arm on hub. Cut off excess cable. Clamp Eyelet MUST be installed in turnbuckle. Allow turnbuckle to loosen or tighten. 4 Install second arm with 4 self-tapping screws. Adjusting and Locking Assembly After adjusting cable tension, lock turnbuckle with nuts to keep turnbuckle from twisting. Lock eye bolt with nut to keep eye bolt from twisting. Inner Arm Side View of Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely. Important: Do not adjust cable too tight or it will bind C-6- Copyright 0 DoorKing, Inc. All rights reserved.
10 PLASTIC FOLDING ARM KIT This kit is designed for the 600 model barrier gate operators only. Recommended for low headroom applications. Kit Includes: Plastic Arms Attachment Assembly Clamp Locking Turnbuckle Eyelet (Connected) Locking Eye Bolt Arm Hinge 8 Self Tapping Screws Installation Cut Arms to Length Note: Completed folding arm assembly shown in the UP position to illustrate the total height. Cut this arm first for the height limitations. Determining First Arm Length Total Height Note: Completed folding arm assembly shown in the DOWN position to illustrate Cut this arm second for the Note: Second arm can be a different size than the first. Determining Second Arm Length Traffic Lane Width
11 Installing Arms Existing Stud Top View of Hub Adjust to clear hub. Remove stud from operator housing and assemble as shown. Bolt Head (Inside Housing) Washer (Inside Housing) 3 Install cable. MUST clear hub! Install eye bolt into arm hinge with vise-grips. Attach arm hinge to inner arm with 4 self-tapping screws. Install inner arm on hub. Cut off excess cable. Clamp Eyelet MUST be installed in turnbuckle. Allow turnbuckle to loosen or tighten. 4 Install outer arm with 4 self-tapping screws. Adjusting and Locking Assembly After adjusting cable tension, lock turnbuckle with nuts to keep turnbuckle from twisting. Lock eye bolt with nut to keep eye bolt from twisting. Inner Arm Side View of Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely. Important: Do not adjust cable too tight or it will bind B-6- Copyright 0 DoorKing, Inc. All rights reserved.
12 WOOD FOLDING ARM KIT This kit is designed for the 600 model barrier gate operators only. Recommended for low headroom applications. Kit Includes: 4 Bolts with Bolt with Bolt with Brass Attachment Assembly s (Small) and (Medium) and (Large) Clamp Wood Arms Eyelet Locking Turnbuckle Hinge Plates Installation Cut Arms to Length Note: Completed folding arm assembly shown in the UP position to illustrate the total height. Cut this arm first for the height limitations. Determining First Arm Length Total Height Note: Completed folding arm assembly shown in the DOWN position to illustrate Cut this arm second for the Note: Second arm can be a different size than the first. Determining Second Arm Length Traffic Lane Width
13 Installing Attachment Assembly Adjust to clear hub. Remove stud from operator housing and assemble as shown. Bolt Head (Inside Housing) Washer (Inside Housing) Installing Arms Inner Arm Turnbuckle Installing Hinge Plates Bolt (Medium) Bolt (Large) Existing Stud 4 Bolts (Small) Top View of A Brass 4 s Hub Install inner arm on hub. Cut off excess cable. 3 Install cable. MUST clear hub! Clamp Eyelet MUST be installed in turnbuckle. A Install hinge plates. Allow turnbuckle to loosen or tighten. Adjusting and Locking Assembly After adjusting cable tension, lock turnbuckle with nuts in position shown to prevent turnbuckle from rubbing against hinge plates when the arm is in the UP position. Inner Arm Side View of Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely. Important: Do not adjust cable too tight or it will bind B-6- Copyright 0 DoorKing, Inc. All rights reserved.
14 60 Manual Release Kit This kit is designed for the 60 barrier gate operator WITHOUT the convenience open option. It provides an interlock power cut-off switch when manually using crank tool to move the arm up or down. DO NOT install on convenience open models. Kit Includes: Pre-wired Interlock assembly, Double motor pulley, Crank tool, spring clips with lock nuts. Installation Shut off the AC input power to the operator from the circuit breaker. Mount spring clips with lock nuts on existing threaded studs inside access door. Crank Tool Storage Replace existing single motor pulley with double motor pulley. Align motor pulley with gear reducer pulley. Mount interlock assembly using existing hardware. Use existing wire restrainers to run wires. Keep wires clear of all moving parts Interlock Assembly Gear Reducer Wiring Interlock DANGER HIGH VOLTAGE! NC NO Interlock Cut-Off Switch Existing 5 VAC Power Terminal Wire Replace the existing AC power switch wire connected to terminal # with interlock cut-off switch wires. AC Power Switch
15 Manual Operation Unlock and remove access door.. Remove crank tool from inside access door. 3. Flip interlock assembly door up, power will be disabled from operator. 4. Insert crank tool into motor pulley as shown. 5. Rotate crank tool to manually move operator arm up or down. Access Door Interlock Assembly Door Crank Tool Storage C-5-0 Copyright 00 DoorKing, Inc. All rights reserved.
Installation/Owner s Manual 1603
CFORMS TO ANSI/UL-325 CERTIFIED TO CAN/CSA C22.2 NO. 247 CLASS HP MODEL SERIAL VOLTS PHASE AMPS 60 Hz MAX GATE LOAD 53382 VEHICULAR GATE OPERATOR DoorKing, Inc., Inglewood, CA Installation/Owner s Manual
More informationInstallation/Owner s Manual 1601 / 1602
WARNING MOVING ARM can cause vehicle damage, serious injury or death. STAY CLEAR of arm at all times. NO: Pedestrians Bicycles Motorcycles CFORMS TO ANSI/UL-325 53382 CERTIFIED TO CAN/CSA C22.2 NO. 247
More informationJanuary 2018 PRICE SCHEDULE A 2.0 Vehicular Traffic Control
Section A1 This Price Schedule is effective January 1, 2018. Date Page Comment 1-1-18 All January, 2018 Price Schedule update. 1-26-18 6, 7 Added 1601-180, 1601-181 Gray Housing and 1601-283 Gray arm hub
More informationJanuary 2018 PRICE SCHEDULE A 2.0 Vehicular Traffic Control
Section A1 This Price Schedule is effective January 1, 2018. Date Page Comment 1-1-18 All January, 2018 Price Schedule update. 1-26-18 6, 7 Added 1601-180, 1601-181 Gray Housing and 1601-283 Gray arm hub
More informationSection A1. Vehicular Traffic Control. This Price Schedule is effective January 7, Date Page Comment
January 2019 PRICE SCHEDULE A 2.0 Section A1 This Price Schedule is effective January 7, 2019. Date Page Comment 1-2-19 All January, 2019 Price Schedule update. Specifications subject to change without
More informationSection A1. Vehicular Traffic Control. This Price Schedule is effective January 7, Date Page Comment
January 2019 PRICE SCHEDULE A 2.0 Section A1 This Price Schedule is effective January 7, 2019. Date Page Comment 1-2-19 All January, 2019 Price Schedule update. Specifications subject to change without
More informationJanuary 2018 PRICE SCHEDULE A 2.0 Vehicular Traffic Control
Section A1 This Price Schedule is effective January 1, 2018. Date Page Comment 1-1-18 All January, 2018 Price Schedule update. 1-26-18 6, 7 Added 1601-180, 1601-181 Gray Housing and 1601-283 Gray arm hub
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationInstallation/Owner s Manual 1601 / 1602
CFORMS TO ANSI/UL-325 CERTIFIED TO CAN/CSA C22.2 NO. 247 CLASS HP MODEL SERIAL 53382 VEHICULAR GATE OPERATOR DoorKing, Inc., Inglewood, CA Installation/Owner s Manual 60 / 602 Barrier Gate Operator Use
More informationInstallation/Owner s Manual 1601 / 1602
CFORMS TO ANSI/UL-325 CERTIFIED TO CAN/CSA C22.2 NO. 247 CLASS HP MODEL SERIAL 53382 VEHICULAR GATE OPERATOR DoorKing, Inc., Inglewood, CA Installation/Owner s Manual 60 / 602 Barrier Gate Operator Use
More informationpoollux Power plx-pw60 & plx-pw100
poollux Power plx-pw60 & plx-pw100 ETL LISTED Conforms to UL STD 379; Certifi.ed.to.CSA.STD.C22.2.#218.1 5005508 Installation Instructions Read all instructions before attempting to perform installation
More informationINSTRUCTIONS FOR THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH
INSTRUCTIONS FOR THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH IS NOT FOR "DO-IT-YOURSELF" INSTALLATION. It must be installed by
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More informationTSI Date Group No. Supp. Page
Volvo Trucks North America, Inc. Greensboro, NC USA Timing Gear Cover TSI Date Group No. Supp. Page 11.2001 215 006 1(7) Timing Gear Cover D12C Fig. 1: VOLVO D12C Engine W2003244 This information covers
More informationCHEVY AVALANCHE 1/2-TON ONLY 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# 10173
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net CHEVY AVALANCHE 1/2-TON ONLY 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS 2003-2005 KIT# 10173 Installation of a Performance Automotive
More informationw w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required
-J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationRigMaster Power Service and Repair Manual Document # S901009
Document # S901009 WARNING The following procedures present hazards which can result in injury or death. Only persons qualified to carry out electrical and mechanical servicing should undertake this work.
More informationFirst, check and record the camber and caster readings, they will be adjusted later.
First, check and record the camber and caster readings, they will be adjusted later. The caliper-mounting bosses are machined perpendicular to the spindle so they are an excellent place for the level.
More informationInstallation Instructions Electric Heaters 5 20 kw
Small Packaged Products to 5 Tons Accessory Electric Heaters Cancels: IIK 564A--1 IIK 564A-- 11-01 Installation Instructions Electric Heaters 5 0 kw NOTE: Read the entire instruction manual before starting
More informationInstallation Instructions
NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment
More informationMODEL D-SBG Single Arm Barrier Gate Operator
INSTALLATION AND OWNER S MANUAL MODEL D-SBG Single Arm Barrier Gate Operator UL 325 and UL 991 Listed WITH NITRO BOARD (SEE SUPPLEMENTAL MANUAL) Serial #: Date Installed: Your Dealer: READ THIS MANUAL
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More informationInstallation Instructions Electric Heaters 5 20 kw
Small Packaged Products 2 to 5 Tons Accessory Electric Heaters Cancels: IIK 564A-24-2 IIK 564A-24- -02 Installation Instructions Electric Heaters 5 20 kw NOTE: Read the entire instruction manual before
More informationMODEL D-WBG Wishbone Arm Barrier Gate Operator
INSTALLATION AND OWNER S MANUAL MODEL D-WBG Wishbone Arm Barrier Gate Operator UL 325 and UL 991 Listed WITH NITRO BOARD (SEE SUPPLEMENTAL MANUAL) Serial #: Date Installed: Your Dealer: READ THIS MANUAL
More informationInstallation/Owner s Manual
CLASS MODEL SERIAL HP 53382 DoorKing, Inc., Inglewood, CA Installation/Owner s Manual Use this manual for circuit board 4502-010 Revision K or higher. For operators manufactured July 2011and later. Series
More informationNext, set the bar level and tighten it down. Do this on both the driver and passenger sides.
Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Using two tape measures, measure the outside width at the front and the rear of the tubes. The front dimension
More informationInstallation and Service Manual
RESIDENTIAL PLATFORM LIFTS RPL400 / RPL600 Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTRUCTIONS IS REQUIRED to promote the safety of those installing this product,
More informationBelt Drive January Platform Section Title Change. Description and Operation of the Belt Drive Tensioner System. Removal of the Belt Tensioner
1 01 06-18 SUBJECT DATE Belt Drive January 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0190 DDC-SVC-MAN-0081 GHG17 DD Heavy Duty DD Heavy
More informationCut zip ties and remove 2 plastic wiring harness brackets.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. Included parts: 1 - New Bosch Cp3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/
More informationAgri-Fab OWNERS MANUAL. Model No " ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-0362 CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts 42" ROUGH CUT TRAILMOWER NOTE: Your mower deck will
More informationUnpack. Left Handing (L) the Operator. StrongArmPark DC Breakaway Bracket Installation Video
DC Left Handing (L) Standard. Factory ships left handing operator. NOTE: If your site requires right handing, place the order with your distributor as a StrongArmPark DC with right handing. Handing changes
More informationQuick Connection Panel (QCP) Installation Guide
Quick Connection Panel (QCP) Installation Guide DANGER HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH Read this document first. The installer is responsible for compliance with National Electrical
More informationINSTALLATION INSTRUCTIONS DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD)
INSTALLATION INSTRUCTIONS 1997-1999 DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD) Installation of a Performance Accessories body lift kit will change the vehicle s center of gravity
More informationTechnical Support (707)
Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform
More informationAssembly & Operator s Manual
Assembly & Operator s Manual LiftGator XTR 1200lbs Removable Liftgate TM Visit our website at: www.liftgator.com WARNING: Read the entirety of this manual before using the LiftGator. Failure to do so can
More informationIE B9 A4/A5 Cold Air Intake Install Guide
IE B9 A4/A5 Cold Air Intake Install Guide Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s Cold Air Intake Kit for Audi
More informationDirect-Coupled ControlSet Actuators (120/180/320 in-lbs.) Installation Guide 2-7/16"
Direct-Coupled ControlSet Actuators (120/180/320 in-lbs.) 5" MEP-7200/7500/7800 Series Mounting Installation Guide 3" 3/8" Conduit fitting plate and red plugs 5" Shaft insert INSERT INSERT Position insert
More informationA.C.E.S. Series ACES 3 & 6 MODULE PANELS. System Manual. Touch-Plate Lighting Controls. ACES 3 & 6 Module System Manual
Touch-Plate Lighting Controls ACES 3 & 6 Module System Manual A.C.E.S. Series ACES 3 & 6 MODULE PANELS System Manual Touch-Plate Lighting Controls 1830 Wayne Trace Fort Wayne, IN 46803 Phone: 260-424-4323
More informationJ & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034
J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The Hyperdrive Assault has gone through months
More informationFlorham Park, NJ USA Call (ASCO) for sales or service
Operator s Manual 4000 Series ATS Automatic Open-Transition Transfer Switches D design 30 230A, J design 260 600A, H-design 800 1200A, G-design 1600 4000A, F-design 4000A DANGER is used in this manual
More information~~ " '" :.~ ~. -~ :: ø U) 6Â~ l\ '---_._ , " ~ -1rr-~.." fj PECULIAR HYDRAULICS. " f ',~, ...
FORD V8-30, 35 W-W/O AC 988-99 PECULIAR HYDRAULICS BELT DRIVE, SLC UNDERHOOD VALVE ~. _ Ln c. " f 000000 HPS59 REV. E, ~ ~~ " '" --- -. ',~, ~ -rr-~.." fj..-:.~ ~.&I C/~.. ""Q ic ø ~. -~ :: ø U) c: ::
More informationcircuit protection & wiring accessories
circuit protection & wiring accessories J J1 circuit breakers Circuit breakers and fuses are a cost-effective solution to protecting wiring, equipment and subsystems. While fuses are a one-time, disposable
More informationWOOD CHIPPER WC1105 5PQ (8/08/2012)
O P E R A T O R ' S M A N U A L WOOD CHIPPER WC1105 5PQ990102 (8/08/2012) To the Owner; Thank-You for choosing a quality product from Frontier Equipment. We strive to give you the best equipment and the
More informationInstallation Instructions
Installation Instructions MX3635-01 Rev. E Models HydraSwing 40s HydraSwing 40F 4,000 lb (1,814 kg) 10-15 seconds HydraSwing 40 4,000 lb (1,814 kg) 15-20 seconds HydraSwing 40 Twin 4,000 lb (1,814 kg)/leaf
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationTEMPORARY ELECTRIC WIRING FOR CARNIVALS, CONVENTIONS, EXHIBITIONS, FAIRS AND SIMILAR USES
INFORMATION BULLETIN / PUBLIC - ELECTRICAL CODE REFERENCE NO.: LAMC 93.0230 Effective: 3-24-69 DOCUMENT NO. P/EC 2002-006 Revised: 11-17-00 Previously Issued As: RGA #7-69 TEMPORARY ELECTRIC WIRING FOR
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationShown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN
Shown with optional GFR-1017R Body Posts J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationJEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# KIT# 973
JEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS 1997-2006 2 KIT# 972 3 KIT# 973 WARNING Installation of a Performance Automotive Group body lift will change
More informationDWHOIST. Drywall Hoist Assembly & Operating Instructions
DWHOIST Drywall Hoist Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important information
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationfor Reproduction Not Brighter. Warmer. Safer. Portable Industrial Heaters Portable Light Towers Portable Light Stands Solar Flashing Arrow Boards
Brighter. Warmer. Safer. Portable Industrial Heaters Portable Light Towers Portable Light Stands Solar Flashing Arrow Boards en Copyright 06 Allmand Bros., Inc. Holdrege, NE, USA. All rights reserved.
More informationAutomatic Roof Hatch Opener
Automatic Roof Hatch Opener Installation Guide REQUIRED TOOLS (These tools are required to complete the installation) Cordless Drill 1/8 1/4 Drill Bits 1/8 Pin Punch #2 Philips Bit Rachet Sharpie Hammer
More informationOutdoor Enclosure Power System ENC X100MP48F20-AC6
Outdoor Enclosure Power System ENC673034-1X100MP48F20-AC6 Manual MA015151A4 Issue 1 Nov 2010 Copyright 2010 Myers Power Products, Inc. Part# A015151A4 MA015151A4 Iss1 Page 1 of 24 Dimensions Outdoor Enclosure
More informationRated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications
WPC2-XXXX-T Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More information3ATS & 3NTS J-design 600 A 3ADTS & 3NDTS A Transfer Switches. Installation Manual. Installation A DANGER. Table of Contents WARNING
ASCO 3ATS, 3ADTS, 3NTS, 3NDTS 3ATS & 3NTS J-design 600 A 3ADTS & 3NDTS 150-600 A Transfer Switches DANGER is used in this manual to warn of a hazard situation which, if not avoided, will result in death
More informationWOOD CHIPPER WC1103 5PQ (8/02/12)
O P E R A T O R ' S M A N U A L WOOD CHIPPER WC1103 5PQ990101 (8/02/12) To the Owner; Thank-You for choosing a quality product from Frontier Equipment. We strive to give you the best equipment and the
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationC Power Connection Kit
1548-4000C Power Connection Kit For use with Dekoron 2700 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4000C electrical connection kit distirbuted by Heat-Line is
More informationJeep Wrangler 4.0 Liter TJ Jeep Wrangler 2.5 Liter TJ Installation instructions
TM www.jeepair.com 1999 Jeep Wrangler 4.0 Liter TJ 1999-2001 Jeep Wrangler 2.5 Liter TJ Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The Jeep kit
More informationFORD SPORT TRAC 2&4WD 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT #70023
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net FORD SPORT TRAC 2&4WD 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS 2001-2002 KIT #70023 WARNING Installation of a Performance Accessories
More informationFlameproof Alternator
Flameproof Alternator Installation, Operation and Maintenance Alternator Types ASX-400 ASX-401 CE242 (6) ASX_0210 DESCRIPTION Twelve pole rotating field coil type externally excited alternators designed
More informationHeating Cable. Construction
Mineral Insulated High Temperature A C Constant Wattage Series Resistance Heating Cable Sets Process Temperature Maintenance to F (593 C) Maximum Exposure Temperature 4 F (76 C) (Power Off) Corrosion Resistant
More informationCHEVY/GMC /2-TON PICKUP 3 BODY LIFT INSTALLATION INSTRUCTIONS 2006 KIT# PA10163 MANUAL TRANSMISSION VEHICLES REQUIRE KIT# PA4701
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net CHEVY/GMC 1500 1/2-TON PICKUP 3 BODY LIFT INSTALLATION INSTRUCTIONS 2006 KIT# PA10163 MANUAL TRANSMISSION VEHICLES REQUIRE KIT# PA4701
More informationInstallation and Service Instructions for Self Adjust Brakes 81,000 Series
Spring-Set Disc Brakes P/N -07-9-00 effective 07/0/0 Installation and Service Instructions for Self Adjust Brakes,000 Series Current revision available @ www.stearns.rexnord.com Tools required for installation
More informationOFFICE PARTITIONS. Data Port Openings. Use cable tie bracket to dress data cables under panels. STEP 1
N Power Box Opening Data Port Openings Rear View Front View Remove opening blanks on raceway cover for power and data. If panel contains no electric or data and is used as a pass-thru, leave opening blanks
More informationBREAK-SAFE Load Break & Pick-up Tool
BREAK-SAFE Load Break & Pick-up Tool USBS-15-1-PS USBS-15-2-PS USBS-27-1-PS USBS-27-2-PS USBS-38-1-PS USBS-38-2-PS USBS-46-1-PS USBS-46-2-PS Available Options: H - Hard Case S - Soft Case Second Generation
More informationINSTALL MANUAL. FOR ON LINE ORDERING- E Commerce Visit Our Website
INSTALL MANUAL FOR ON LINE ORDERING- E Commerce Visit Our Website WWW.PRESSUREGUARD.COM Contact Information Technical Support: Chris@pressureguard.com Sales Support: Sales@pressureguard.com By Phone: 615-227-6024
More information2013 Edge, MKX Workshop Manual
7. Remove the 3 bolts and the generator. Installation 1. Position the generator and hand tighten the 3 bolts. Tighten in the sequence shown. Tighten to 25 Nm (18 lb-ft). 2. Connect the generator electrical
More informationAgri-Fab OWNERS MANUAL. Model No " FINISH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-0305 63" FINISH CUT TRAILMOWER CAUTION: Read Rules for Safe Operation and Instructions Carefully NOTE: Your mower deck will require a 12 volt battery to operate. This
More informationRevised 10/22/2014 Page 2 of?
1.Remove side panels, hood, seat, fuel tank, and 2.Remove stock air box, remove fuel line muffler. Save exhaust springs and rubber muffler mounts for turbo bracket. Sand back surface flat for mounting.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2013-2014 Honda CBR500R/RA Tour Performance Handlebar Risers P/N: HR01087 IMPORTANT: PLEASE GIVE CUSTOMER ENCLOSED INFORMATION! Thank you for your purchase of our HeliBars. They
More informationDODGE DAKOTA 3 KIT INSTALLATION INSTRUCTIONS KIT# 60043
DODGE DAKOTA 3 KIT INSTALLATION INSTRUCTIONS 2000-2002 KIT# 60043 Installation of a Performance Automotive Group body lift kit will change the vehicle s center of gravity and handling characteristics both
More informationJeep Wrangler TJ. Complete Air Conditioning System. Slide Control Head. Installation instructions
WWW.JEEPAIR.COM 1996-1998 Jeep Wrangler TJ Complete Air Conditioning System Slide Control Head Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The
More informationBill of Materials for
Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1
More information2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014
2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &
More informationSpecial Note About The JDM High Performance Water Pump:
Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering
More information3. Cover the hood with padding and fold the stock windshield frame down onto the hood.
640 North El Dorado Street Stockton, CA 95202 Phone (209)943-0991 Fax (209)943-7923 www.wildhorses4x4.com Stainless steel windshield frame #5722 Date 10/30/07 Parts list: 1-10 ¾ long 1/4 NF threaded rod.
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationInstallation/Owner s Manual
53382 HP Read owner s manual and safety instructions. Installation/Owner s Manual Use this manual for circuit board 4502-010 Revision K or higher. For operators manufactured July 2011and later. Series
More informationI. Before starting installation
5. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. A. Disconnect battery cables 1. Disconnect the negative cable first, then the
More informationTOYOTA TUNDRA 3 BODY LIFT INSTALLATION INSTRUCTIONS 2014 KIT# 5643
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net TOYOTA TUNDRA 3 BODY LIFT INSTALLATION INSTRUCTIONS 2014 KIT# 5643 Installation of a Performance Automotive Group body lift kit will
More informationMOTORIZED INSTALLATION INSTRUCTIONS
MOTORIZED Mega-Pro Swinging Doors Motorized Accordion Strip Doors INSTALLATION INSTRUCTIONS Save-T Roll-Up Bug Screen Save-T Vinyl Roll-Up Screen Save-T Guard Security Gates Save-T Flex-Guard Chain Link
More informationJEEP WRANGLER JEEP WRANGLER UNLIMITED 2 & 4 DOOR 2 BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# 992
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net JEEP WRANGLER JEEP WRANGLER UNLIMITED 2 & 4 DOOR 2 BODY LIFT KIT INSTALLATION INSTRUCTIONS 07-08 KIT# 992 Installation of a Performance
More informationIncluded parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please contact H&S Motorsports
More informationMODEL WBG WISHBONE BARRIER GATE OPERATOR
TABLE OF CONTENTS MODEL WBG WISHBONE BARRIER GATE OPERATOR Important Safety Information.....3 System Designer Safety Instructions.......4 Installer Safety Instructions........ 5 End User Safety Warnings...-
More informationTCI FastGate Shifter Installation Instructions
151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The
More informationPortable Lighting Equipment Operating Instructions Table of Contents
Portable Lighting Equipment Operating Instructions Table of Generac Magnum Ingersoll Rand TEREX AMIDA TEREX GENIE Model: MLT3060 Model: LIGHTSOURCE Model: Amida AL4000 series Model: TML4000N Generac Magnum
More informationInstallation Instructions
Installation Instructions Speedcook Oven Read carefully. Keep these Instructions. INSTALLATION INSTRUCTIONS Electrical Requirements Product rating is 240/208 volts AC, 60 Hertz, 30 amps and 6.5 kilowatts.
More informationEGR Performance Brakes Assembly Instructions DODGE DANA 70 '87 - '93 (Will not fit stock sized dual rear wheels)
EGR Performance Brakes Assembly Instructions DODGE DANA 70 '87 - '93 (Will not fit stock sized dual rear wheels) Got Brakes? Parts List (2) Vented Rotors (2) Multi hole Cable Mount & L Brkt (2) Axle Tube
More informationL Ford Power Stroke Intercooler Pipe Upgrade
Rev: 10.30.14 TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect
More informationPower-Limiting Cables
Power-Limiting Cables This section provides general design guidelines for power-limiting heat-tracing systems installed on insulated metal pipes. For other applications or design assistance, contact your
More informationFlameproof Alternator
Flameproof Alternator Models ASX-400, ASX-401 Application l For use in hazardous areas classified as Zone 1, Group IIB, T4 l Suitable for local ambient temperature range -30 C to +50 C l Designed as a
More information