ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L >
|
|
- Buddy Houston
- 6 years ago
- Views:
Transcription
1 Print 2003 Subaru Forester 2.5L Eng X ENGINE CONTROLS - ON-VEHICLE ADJUSTMENTS ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L > 1. Set the vehicle onto the lift. 2. Lift-up the vehicle. 3. Remove the under cover. See. 4. Disconnect the ground terminal from battery. See. 5. Lower the vehicle. 6. Remove the timing belt cover. See. 7. When inspecting No. 1 and No. 3 cylinders; remove the air intake duct as a unit. See. Remove the resonator chamber. See. Disconnect the spark plug cords from the right side spark plugs. Disconnect the PCV hose from the right rocker cover. Remove the bolts, then remove the right rocker cover. 8. When inspecting No. 2 and No. 4 cylinders; remove the battery and battery carrier. Disconnect the window washer motor connectors. Remove the two bolts which hold washer tank, then secure the tank away from working area. See. Disconnect the spark plug cords from the left side spark plugs. Disconnect the PCV hose from the left rocker cover. Remove the bolts, then remove the left rocker cover. NOTE: When the arrow mark (A) on left camshaft sprocket comes exactly to the top, No. 1 cylinder piston is brought to top dead center of compression stroke. See. 9. Set No. 1 cylinder piston to top dead center of compression stroke by rotating the crank shaft pulley clockwise using Crankshaft Pulley Wrench ( ). CAUTION: Insert the thickness gauge in as horizontal a direction as possible with respect to the valve stem end face. Measure the exhaust valve clearances while lifting-up the vehicle. See table. VALVE CLEARANCE SPECIFICATION (2.0L & 2.5L) Application Clearance - In. (mm) 2.0L & 2.5L Intake ( ) Exhaust ( ) 10. Measure No. 1 cylinder valve clearance by using thickness gauge (A). See.
2 NOTE: Ensure the cylinder pistons are set to their respective top dead centers on compression stroke before measuring valve clearances. To set No. 3, No. 2 and No. 4 cylinder pistons to their top dead centers on compression stroke, turn the crankshaft pulley clockwise 90 degrees at a time starting with arrow mark on left camshaft sprocket facing up. See. 11. Using procedures similar to what was used for No. 1 cylinder, measurement measure No. 2, No. 3 and No. 4 cylinder valve clearances. 12. If necessary, adjust the valve clearance. See under VALVE ADJUSTMENT. After inspection, install the related parts in the reverse order of removal. Fig 1: Removing Right Timing Belt Cover
3 Fig 2: Removing Resonator Chamber
4 Fig 3: Identifying Top Dead Center For Cylinder No. 1, Using Left Camshaft Arrow
5 Fig 4: Measuring No. 1 Valve Clearance
6 Fig 5: Identifying Top Dead Center For Cylinders No. 3, 2 & 4, Using Left Camshaft ENGINE MECHANICAL > VALVE ADJUSTMENT > CAUTION: Adjustment of valve clearance should be performed while engine is cold. ENGINE MECHANICAL > VALVE ADJUSTMENT > 2.5L >
7 NOTE: When the arrow mark (A) on left camshaft sprocket comes exactly to the top, No. 1 cylinder piston is brought to the top dead center of compression stroke. 1. Set No. 1 cylinder piston to top dead center of compression stroke by rotating the crankshaft pulley clockwise using Crankshaft Pulley Wrench ( ). See. CAUTION: Insert the thickness gauge in as horizontal a direction as possible with respect to the valve stem end face. See. Adjust the exhaust valve clearances while liftingup the vehicle. See table. 2. Adjust the No. 1 cylinder valve clearance. Loosen the valve rocker nut and screw. Place suitable thickness gauge. While noting the valve clearance, tighten the valve rocker adjust screw. When the specified valve clearance is obtained, tighten the valve rocker nut to 7.2 ft. lbs (10 N.m). See. 3. Ensure the valve clearances are within specifications. See table. 4. Turn the crankshaft two complete rotations until No. 1 cylinder piston is again set to top dead center on compression stroke. 5. Ensure the valve clearances are within specifications. If necessary, readjust the valve clearances. NOTE: Ensure to set the cylinder pistons to their respective top dead centers on compression stroke before adjusting valve clearances. To set No. 3, No. 2 and No. 4 cylinder pistons to their top dead centers on compression stroke, turn the crankshaft pulley clockwise 90 degrees at a time starting with arrow mark on left camshaft sprocket facing up. See. 6. Using similar adjustment procedures used for No. 1 cylinder, adjust No. 2, No. 3 and No. 4 cylinder valve clearances.
8 Fig 1: Adjusting Valve Clearance 2.5L
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationhttps://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html
Page 1 of 7 NOTE: The timing pin is used to accurately locate TDC for setting the overhead. The timing pin is typically located below the fuel pump. for front gear train engines, in the front gear housing
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More information2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required
More informationGM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
More informationTiming Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.
More informationValve Clearance Adjustment
2006 Odyssey Valve Clearance Adjustment Report a problem with this article NOTE: Adjust the valves only when the cylinder head temperature is less than 100 ºF (38 ºC). 1. Remove the intake manifold. 2.
More information2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300
Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)
More informationAdjusting valve clearance
Adjusting valve clearance Engines314, 352, 352 A 355, 355 A 360, 360 A 362 LA 364, 366, 366 A/ LA Adjustment values in mm Engine Intake valve Exhaust valve Tolerance range 1) 314, 352, 352 A.V 2) 0.20
More information2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum
1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to
More informationRecommended Installation Procedure ATech Timing Belt Tensioner DaimlerChrysler PL, PT, JR 2.0L 4-Cyl. Engine (10/27/2003)
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to DAIMLERCHRYSLER PL s guidelines. The mounting of the TBT
More information2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More informationCYLINDER HEAD > CAMSHAFT, ENGINE > REMOVAL > LEFT
Page 1 of 12 2012 Dodge Grand Caravan 3.6L Eng Crew Service Manual: 3.6L ENGINE - SERVICE INFORMATION CYLINDER HEAD > CAMSHAFT, ENGINE > REMOVAL > LEFT Fig 1: Magnetic Timing Wheels The magnetic timing
More information1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza
1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST
More information2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More informationTiming Drive Components ( )
Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner
More information& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.
Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace 1993-97 626 & MX-6 This engine is classified as an Interference engine. If the timing belt breaks
More informationRecommended Installation Procedure (11 DEC 09) ATech Timing Belt Tensioner (979847/901) VW 1.6/2.0L L4 EA189 CR Engine
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to VW s guidelines. The mounting of the TBT is done on the
More informationIntake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
More information1998 Volkswagen Golf GL
Removal (Thermo Tensioner Roller - 1997 & Up) CAUTION: To prevent valves from contacting piston, DO NOT rotate camshaft or crankshaft with timing belt removed. Valve damage may result. 1. Remove air cleaner
More informationMECHANICAL ME(SOHC) Page
ME(SOHC) Page 1. General Description...2 2. Compression...23 3. Idle Speed...24 4. Ignition Timing...25 5. Intake Manifold Vacuum...26 6. Engine Oil Pressure...27 7. Fuel Pressure...28 8. Valve Clearance...29
More information1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
More informationCAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet
More information2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More informationTORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43
More information1 of 17 2/19/ :10 AM TIMING BELT
1 of 17 2/19/2012 11:10 AM TIMING BELT 2 of 17 2/19/2012 11:10 AM INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 3 of 17 2/19/2012 11:10 AM 2) Install left-hand belt cover No.2. 3) Install
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Rocker Arm Assembly» Service and Repair» Procedures» Cam, Valve Springs & Seals, Cam Roller Follower and Lifter Camshaft, Valve Springs,
More information1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT
1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT CAUTION: a. Do not bend or twist timing belt. b. After removing timing belt, do not turn crankshaft and
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationService and Repair Note:
Service and Repair Note: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Drive Components - Timing
More informationService and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.
1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling
More informationADJUSTING VALVE CLEARANCE
ADJUSTING VALVE CLEARANCE ADJUSTING VALVE CLEARANCE a Adjusting instrument for valve clearance 4. While the No. 1 cylinder is at the compression top dead center, adjust the valve clearances marked with
More informationTiming Belt: Service and Repair
2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata
More information15.Timing Chain Assembly
15. A: REMOVAL 1. TIMING CHAIN RH When replacing a single part, perform the work with the engine assembly installed to body. 1) Remove the chain cover. 2) Using
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More informationTIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
More informationTIMING BELT REPLACEMENT. Removal Procedure. Tools Required J Timing Belt Alignment Kit J Crank Hub Torx Socket
1 of 15 3/19/2012 5:34 PM TIMING BELT REPLACEMENT Removal Procedure Tools Required J 42069 Timing Belt Alignment Kit J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection
More information5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose.
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to manufacturer s guidelines. Cold Engine Cold tensioner: 1.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
More information2002 Mitsubishi Montero Limited
Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components
More informationREMOVAL AND REPLACEMENT
2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More informationRecommended Installation Procedure (25 MAY 07) ATech Timing Belt Tensioner (979778) FIAT FIRE 8-valve 1.2/1.4L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationCAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000
More information1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
More information- 1/7 - Copyright Litens Automotive Group All rights reserved.
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More informationRecommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004)
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationTOOTHED DRIVE BELT, REMOVING, INSTALLING AND TENSIONING
2005 Audi A4 Sedan (8E2) L4-1.8L Turbo (AMB) Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Removal and Replacement TOOTHED DRIVE BELT, REMOVING,
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More informationIN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
More information2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair
2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page
More informationVALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
More informationTIMING BELT (4A FE) COMPONENTS
EM30 Timing Belt (4AFE) TIMING BELT (4AFE) COMPONENTS REMOVAL OF TIMING BELT 1. REMOVE RH FRONT WHEEL 2. REMOVE RH ENGINE UNDER COVER 3. REMOVE WASHER TANK 4. LOOSEN WATER PUMP PULLEY BOLTS AND REMOVE
More informationTech Talk. Timing Belt 6VD1/6VE1
Holden DOHC V6 Frontera 6VD1 3.2L 1999 2004 Jackaroo 6VE1 3.5L 1998 2004 Rodeo TF 6VD1 3.2L 1998 2003 Rodeo RA 6VE1 3.5L 2003 2005 Important: Read through all the instructions before proceeding with the
More informationIN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Disconnect the eight ignition coil electrical connectors.
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components 303-01A-1 Special Tool(s) Compressor, Valve Spring 303-581 (T97T-6565-A) Holding Tool, Crankshaft 303-448 (T93P-6303-A) 3. Disconnect the eight ignition
More informationVALVE TIMING CHECK-TIMING BELT COVER INSTALLED
TIMING BELT SERVICE VALVE TIMING CHECK-TIMING BELT COVER INSTALLED 1. Remove number one spark plug. 2. Using a dial indicator; set number one cylinder to TDC on the compression stroke. 3. Remove the access
More informationASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More information11A-1 ENGINE CONTENTS
11A-1 ENGINE CONTENTS ENGINE ENGINE ... 11A... 11B 11A-2 ENGINE CONTENTS GENERAL... 3 Outline of Changes... 3 GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 3 SPECIAL
More information2002 Escape Workshop Manual
SECTION 303-01B: Engine 3.0L (4V) IN-VEHICLE REPAIR Procedure revision date: 10/09/2003 Timing Drive Components Removal CAUTION: Failure to verify correct timing drive component alignment will result in
More informationRECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More informationTiming Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
More information1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationUse Installation Procedure 1 when the crankshaft has NOT been rotated from the original position.
2001 Blazer 4WD Applies to: 4.3L Report a problem with this article Removal Procedure Notice: There are two procedures available to install the distributor. Use Installation Procedure 1 when the crankshaft
More information1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationATech Timing Belt Tensioner (979572) VM MOTORI 2.5L Diesel, Common Rail Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More information2001 Escort Workshop Manual
Page 1 of 6 SECTION 303-01B: Engine 2.0L Zetec 2001 Escort Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/26/2004 Timing Drive Components Timing Belt Special Tool(s) Crankshaft TDC Timing
More information1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
More informationThe following tools will be required to perform this new service procedure outlined in this bulletin:
The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure
More informationClassification: Reference: Date: VE30DE CAM TIMING
Classification: Reference: Date: EM93-002 NTB93-126 September 2, 1993 VE30DE CAM TIMING APPLIED VEHICLE(S): All equipped with VE30DE Engine SERVICE INFORMATION When servicing VE30DE engine cylinder heads,
More informationCAMSHAFT INSTALLATION INSTRUCTIONS FOR NISSAN KA24DE ENGINES W/DOUBLE ROW CHAIN (SEE LAST PAGE FOR USING JWT CAMS IN KA24DE W/SINGLE ROW CHAIN)
9/13 UPDATE CAMSHAFT INSTALLATION INSTRUCTIONS FOR NISSAN KA24DE ENGINES W/DOUBLE ROW CHAIN (SEE LAST PAGE FOR USING JWT CAMS IN KA24DE W/SINGLE ROW CHAIN) 1. It is highly recommended that an oil and filter
More information2012 Honda Crosstour EX ENGINE Cylinder Head - (4-CYL)
Fig. 4: Identifying Cylinder Head Components Location (3 Of 3) ENGINE COMPRESSION INSPECTION NOTE: After this inspection, you must reset the PCM. Otherwise, the PCM will continue to stop the fuel injectors
More informationPage 1 of 8 2005 Volvo S40 2.4L Eng Base TIMING BELT REPLACEMENT - 2.4L & 2.5L TURBO, 5-CYLINDER REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft
More information2004 Chevy Truck Silverado WD V6-4.3L VIN X
1 of 14 10/17/2013 8:32 PM 2004 Chevy Truck Silverado 1500 2WD V6-4.3L VIN X Vehicle» Powertrain Management» Ignition System» Distributor» Service and Repair» Distributor Replacement DISTRIBUTOR REPLACEMENT
More informationValve Timing Inspection and Adjustment
Document ID: 2094866 http://localhost:9001/si/showdoc.do?docsyskey=2094866&pubcellsyskey=123728&pubo... Page 1 of 3 2009 Chevrolet Aveo Aveo, Wave, G3, Barina (VIN S/T) Service Manual Engine Engine Mechanical
More information1. Remove the timing belt upper front cover. Refer to Timing Belt Upper Front Cover Removal.
2013 Sonic Applies to: 1.8L (LUW, LWE) Report a problem with this article Special Tools EN-652 Flywheel Holder EN-6333 Locking Pin EN-6340 Locking Tool EN-6628-A Locking Tool EN-45059 Torque Angle Sensor
More informationFUNDAMENTAL OF AUTOMOBILE SYSTEMS
Prof. Kunalsinh Mechanical Engineering Dept. FUNDAMENTAL OF AUTOMOBILE SYSTEMS Prof. Kunalsinh kathia [MECHANICAL DEPT.] UNIT-2 [ENGINES] PART-1 Prof. Kunalsinh kathia [MECHANICAL DEPT.] Internal combustion
More informationCAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.
CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.4L) Document ID# 2133175 Camshaft Timing Chain, Sprocket, and Tensioner
More informationTiming Belt: Service and Repair Timing Belt Replace. Timing Belt Removal
1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley
More informationRemoval Procedure. Remove the timing chain tensioner. 1 of 32 12/17/ :42 AM
1 of 32 12/17/2011 11:42 AM Removal Procedure 1. 2. 3. 4. 5. 6. Remove the camshaft cover. Raise and support the vehicle. Remove the No. 1 cylinder spark plug. Rotate the crankshaft in the engine rotational
More informationValvetrain, servicing
Page 1 of 51 15-32 Valvetrain, servicing Note: Cylinder heads with small cracks between the valve seats that are less than 0.3 mm (0.012 in.) wide and/or between one valve seat and only the first 4 threads
More information