Installation/Operating Instructions Flatscreen Lift by Draper

Size: px
Start display at page:

Download "Installation/Operating Instructions Flatscreen Lift by Draper"

Transcription

1 Caution 1 Read instructions completely before proceeding. 2 Follow instructions carefully. Installation contrary to instructions invalidates warranty. 3 The Flatscreen Lift must be installed on a ¾" thick back panel, such as plywood, MDF or other stable material. 4 Do not obstruct operation of lift with fingers or any object. Serious injury or damage could result. 5 Installer must provide adequate structure, and must also secure furniture to wall to prevent tipping. 6 For displays larger than 60", a special bracket may be required. Call Draper for assistance. Note: Unit has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Please unpack your shipment and verify that you have received all of the parts listed below. Lift and components ship in two cartons. One (1) U-channel mounting bar (packed in separate carton) One (1) FSL Lift One (1) Control Box One (1) RF Remote Control One (1) Control Cable Wiring (attaches controller to lift) One (1) Power Cord One (1) Universal TV Mount One (1) Set 8 bolts and nuts One (1) Secondary Shelf Two (2) Secondary Shelf Stop Brackets One (1) Set of Lift Mounting Directions/Controller Programming Instructions Installation/Operating Instructions Flatscreen Lift by Draper 2 The lift controller has an intermittant two cycle operation one cycle to its upper position and one cycle to its lowered position. The controller cycles should always start in the lowered position. The cycle time is 50 seconds on, 150 seconds off. 3 The Maximum environment temperature of controller is not to exceed 104 F (40 C). 4 Do not use this apparatus near water or moisture for example, in a wet basement, near a swimming pool, etc. 5 Clean only with dry cloth. 6 Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 7 Do not install near any heat sources, including radiators, heat registers, stoves, or other equipment (including amplifiers) that produces heat. 8 Do not install without proper use of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician. 9 Protect the power cord from being stepped on or pinched, particularly at the plugs, convenience receptacles and the point where the cord exits from the apparatus. 10 Only use attachments/accessories specified by the manufacturer. 11 Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Hardware RF Remote Controller Cable Lift Control Box Secondary Shelf U-Shaped Mounting Bar You will need the following tools to install the lift: One #2½ metric Allen wrench One #4 metric Allen wrench One #5 metric Allen wrench One drill with a #2 Phillips head screw tip One #5 Vix bit Secondary Shelf Stop Brackets Universal TV Mount and Hardware Important Safety Instructions 1 The lift requires a minimum load of 15 lbs in order to function properly. This can be achieved by either (1) attaching weight to the mounting brackets, or (2) manually applying hand pressure at the top of both slides during operation. Caution: If manually applying pressure to the top of both slides, keep hands, clothing and other objects out of the operational area of the lift. 12 Unplug the apparatus during lightning storms or when unused for long periods of time. 13 Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, including but not limited to: power supply cord or plug cut, frayed or otherwise damaged; liquid spilled/objects fallen into the unit; exposure to rain or moisture; unit not operating normally; or unit has been dropped. 14 WARNING: The main plug/appliance coupler/direct plug-in adapter is used as a disconnect device. The disconnect device MUST remain readily available within easy reach. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK. DO NOT OPEN RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR. 15 This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. Where in a manufacturer s service documentation, for example in circuit diagrams or lists of components, a symbol is used to indicate that a specific component shall be replaced only by the component specified in that documentation for safety reasons. 16 When apparatus operation and installation instructions contain instructions for use by service personnel, such instructions shall be separate in format from other instructions and preceded by the word CAUTION and the following or the equivalent. These servicing instructions are for use by qualified service personnel only: To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 17 A warning that an apparatus with class I construction shall be connected to a mains socket outlet with a protective earthing connection. 18 The unit shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the unit. Copyright 2013 Draper Inc. Form FSL_Inst13 Printed in U.S.A. If you encounter any difficulties installing or servicing your FSL Flatscreen Lift, call your dealer or Draper, Inc. in Spiceland, Indiana, , or fax

2 Flatscreen Lifts by Draper, Inc. page 2 of 6 Installing Unit The FSL Flatscreen Lift must be installed on a ¾" thick back panel, such as plywood, MDF or other stable material. Please Note: The top of back panel including lift U channel bracket must be installed ¼" below inside front and sides of the cabinet. Caution: Prior to installing, ensure the furniture/cabinetry being used is large enough and strong enough to hold the FlatScreen Lift (in the fully upright position) and the display without tipping (see diagram on next page for minimum height requirements). If attaching to wall, installer is responsible for ensuring appropriate hardware is used and wall and studs are strong enough to hold the combined weight of the display and the lift. 1 Place "U" Channel Mounting Bar (see Fig. 1) down on the top edge of the ¾" back panel with the four pre-drilled holes facing the inside of the furniture where the lift will be placed. The "U" Channel Mounting Bar is press-on fit. 2 Lower the "U" channel on the back of the FSL Flatscreen Lift down over the back panel Mounting Bar and center it on the back panel. 3 Determine where to cut out for the motor in the ¾" thick back panel. (This is easier if the back ¾" panel has not been installed and attached in the actual cabinet yet.) 4 See Fig. 2 for motor cutout location. Cut out the opening to enable motor to pass through back panel. The added clearance around the cut out opening allows the motor and controller wiring cable to be fed inside the cabinet for hook-up. If more space is required for cables, etc., the hole can be enlarged or additional holes can be made in the back panel. U Channel Mounting Bar MODEL DIM A FSL-F-42 25½" FSL-F-50 29½" MOTOR CUT OUT 7" Figure 2 5 Measure down from the top of the "U" Channel Mounting Bar to the location of the two (2) 6 mm threaded anchoring holes on the bottom of the lift (above the motor). Pre-drill the location on the panel with a #5 Vix bit and then drill two 5 /16" holes through the back panel. 6 Mount the lift in place onto the back panel and secure it with two (2) 6 mm x 30 mm bolts using flat washers. The bolts need only be tightened with a firm amount of torque, so as not to distort the back panel. 7 Attach the back ¾" furniture panel with lift into cabinetry and secure. Pull the motor/control wire cable through into the inside opening of the Lift area. 8 Position the controller in a convenient place to the left or right side of the lift at the top of the back panel just below the "U" Channel Mounting Bar. Screw the controller into place using four (4) 7 x 7 /16" pan head mounting screws provided. 9 Attach the male end of the motor/control cable to the female connector on the bottom of the controller. 10 Attach the female connector of the power cord to the male connector on the bottom of the controller. FSL Flatscreen Lift Operation The FSL FlatScreen Lift is operated with an RF Controller (standard) (115V AC or 220V AC). 1 The controller has been pre-programmed to extend to pre-determined height. 2 Press the "Up" button on the remote control to activate the up function. 3 The lift will extend to its pre-programmed height. 4 Attach secondary shelf to mounting brackets. (The secondary shelf has adjustable slots that allow you to center it in the cabinet opening.) 5 Pre-drill into the four holes located on the "U" channel mounting bar with a #5 Vix bit into the back panel. Figure 1 LIFT C L 3" 1 5 /8" DIM A 6 Attach the two 2 1 /8" tall x 3 /8" deep secondary shelf stop brackets by inserting one # 7 x 7 /16" pan head screw into the top of the adjustable slots in each stop bracket. (Hand tighten screw only at this time and rotate brackets sideways on U Channel Mounting Bar.) Do not attach secondary shelf stop brackets lower inside the cabinet. Caution: You must place a load of at least 15 lbs. to the unit before operating the lift. 7 Press the "Down" button on the remote control to activate the down function. (Apply constant downward pressure to the top of both slides at the curved portion of the lift.) 8 As the lift descends press the "Down" button once to halt the lift when the secondary lid stop brackets on the backside of the secondary lid are approximately ¾" below the top of the "U" Channel Mounting Bar. 9 Center the secondary lid bracket in cabinet opening (left and right). Please note: If power to the unit is lost, the FSL has a manual override. Simply remove the two screws from cover on the top of the lift, and use an M8 socket and ratchet or drill to raise or lower the unit. See back page for details. Making the ¾" Secondary Shelf 1 Measure the inside opening width of cabinet opening from the back side of the cabinet front panel to the front of the secondary lid bracket screw heads. 2 Measure the inside opening length of cabinet opening from the inside of the side walls. 3 Manufacture the secondary lid out of the ¾" material. If using veneer edge banding, subtract 3 /16" off depth and 3 /8" off width. If using solid hardwood, subtract an additional 1 /16" off depth and width. Installing the ¾" Secondary Shelf 1 Place the secondary lid from above on the pre-installed secondary shelf and center in the cabinet (left and right). 2 While holding down on the secondary shelf, press the "Up" button on the remote once more to raise the lift. Caution: Beware of getting fingers and hands pinched. 3 Using the Vix bit, pre-drill through pre-registered holes in the secondary shelf bracket. Secure the secondary shelf with appropriate fasteners (not supplied). 4 Press the "Down" button once to lower the lift and secondary lid into the pocket of the cabinet. Stop the lift when the top of the secondary lid is flush with the sides of the cabinet. Rotate the two "L" shaped secondary lid stops into position and tighten securely. 5 Press the "Up" button on the remote once more to raise the lift to its fullest extension height. Caution: Pinch point. Keep hands clear. Please Note: When installing lid on cabinet, make sure: A When fully open the lid is leaning slightly forward (resting against the unit) so it will close as unit is lowered; and B The lid is placed so that if cabinet is placed against the wall the lid has adequate space to open. Dimensions and Data Model FSL-F-42 FSL-F-50 TV Size Up to 42" Up to 50" Maximum TV Height* /16" 28¾" Lift Height /16" 29¾" Lift Width 17" 17" Lift Depth without Brackets 3 1 /16" 3 1 /16" TV Bracket Depth 1" 1" Lift Depth with Brackets** 4 1 /16" 4 1 /16" Lift Height at Max. Ext. 59¼" 73½" Extension 33 7 /16" 43¾" Extension Time 25 sec. 33 sec. Max. Weight Capacity 210 lb 210 lb *If using secondary shelf, and TV height is a concern, contact Draper for recommendations. **Back-panel to back of TV.

3 Flatscreens Lift by Draper, Inc. page 3 of 6 Model Dim A Dim B FSL-F /16" 42" FSL-F /4" 46 1 /16" Dimensions Dimensions with Extensions B 20 1 /2" 32" 17" 8 13 /16" 3 1 /4" 20" 15/16" 3 1 /16" 2 3 /16" A Attaching the FSL Universal TV Mount Kit* Connect the mount plate and lift bracket ➀ Find the M6 x 12 screws with washer and nut in the screw pack. ➁ With the help of an assistant, position the mount plate level against the lift in the desired mounting location. ➂ Mark the right (upper and lower) and the left (upper and lower) positions of the small horizontal slots that are in alignment with vertical slot on the metal studs of the lift. ➃ With the help of an assistant, position the mounting plate against the lift and line up the mounting slots. ➄ For each location, insert a screw, washer and nut with lift bracket. ➅ Tighten each screw with an open ended socket wrench by turning clockwise until tight. Display bracket installation ➀ To ensure optimal installation, this kit includes various screws of different diameters and lengths. ➁ Place your TV screen down on a soft, flat surface, and locate the threaded mounting points that are located on the back of the display. ➂ Determine which screw is the correct length by carefully inserting a straw, or toothpick, and mark how deep the mounting point is. ➃ If your display has a curved back or a recessed thread mounting point, a spacer must be used. ➄ Place the spacer between the mounting bracket and the display. ➅ If a smaller screw is being used, please use a washer with each screw for added stability. Final installation ➀ Attach each bracket to the display by aligning the holes on each bracket, with the thread insert on the back panel of your display, inserting the screws through both and turning clockwise until they are fully inserted. ➁ Tighten with a Phillips head screw driver. ➂ To complete the installation of your new plasma mount, carefully place the television brackets over the upper and lower mounting lips. ➃ Insert the locking rods to secure the mounting bracket. *Displays larger than 60" diagonal may require a special bracket as they may not fit the standard universal mount. Contact Draper for assistance. C Model Dim C Dim D FSL-F /4" 25 3 /8" FSL-F /2" 29" D Warning: Do not obstruct operation of lift with any part of the body, or with any object. Serious injury or damage could result. Keep children clear of unit when in operation, and when in raised position.

4 Flatscreen Lift by Draper, Inc. page 4 of 6 Controller Programming Instructions IMPORTANT: ➀ THE LIFT MUST BE WORKING AGAINST A MINIMUM LOAD OF AT LEAST 15 LBS IN ORDER TO FUNCTION PROPERLY. This can be achieved by either (1) attaching weight to the mounting brackets, or (2) manually by applying hand pressure at the top of both slides during operation. ➁ PLEASE READ THROUGH THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO OPERATE THE CONTROLLER OR THE LIFT. IT WILL SAVE YOU MUCH TIME AND EFFORT. Programming the Controller The controller is pre-programmed and tested at the factory, and should operate properly immediately upon installation. However, there are several functions that can be programmed to your specific requirements. Please note that when power is first applied to the controller, a horizontal flashing bar may appear in the display. If the flashing bar is in the upper right-hand corner (Fig 1), it means that the system thinks the lift is in the fully extended or up position. Fig. 1 Fig. 2 If the flashing bar is in the lower left-hand corner (Fig. 2), it means that the system thinks the lift is in the fully closed or down position. In either case, compare the actual position of the lift with the indication on the display before proceeding with programming. If they are not the same, follow the instructions for Extension Programming before programming other functions. Entering Setup Mode Before any of the functions of the controller can be programmed, you must first enter the Setup mode. To enter the Setup mode, do the following: ➀ Press SETUP and together, and hold for 5 EP should appear on the controller display. The controller is now unlocked and you may now access and program all the controller functions. ➁ By repeatedly pressing SETUP, you may toggle through the functions, which are abbreviated and will appear in the display in the following order: Function Display Extension Programming EP Add remote control A.rc Clear remote control C.rc Current down Cu.d Current Up Cu.U Infrared down Ird Infrared up Iru Count Cou bypass byp ➂ To exit setup mode: Press SETUP until appears in the display, then press. A brief description and procedure for programming each of the functions follows. EP Extension Programming Used to program the lift to stop at any desired extension height. NOTE: WHEN ATTEMPTING TO PROGRAM EXTENSION HEIGHT, IT IS VERY IMPORTANT TO START WITH THE LIFT IN THE FULLY CLOSED OR DOWN POSITION. If you see that the horizontal bar is flashing in the lower left corner of the display, but the lift is not in the lowest or closed position, (which often happens when the up and down buttons have been pushed before the controller is connected to the lift), do the following: ➀ Enter Setup mode by pressing SETUP and together, and holding for 5 ➁ Enter the bypass mode (refer to bypass instructions below). ➂ When in bypass mode, press and hold until the lift reaches its full down position. ➃ Once the lift is in the full down position, check to see whether the horizontal flashing bar is in the lower left-hand corner of the display. If it is not, press. The lift position and the controller will now be synchronized and you may proceed with extension programming. ➄ Press SETUP until EP appears in the display. ➅ Press. The extension height can now be programmed. ➆ Press and hold until the desired height is reached. ➇ To lock in the height setting, press SETUP until the display shows the next available function (in this case, A.rc). ➈ Exit setup mode. Arc Add Remote Control Use to add a second remote control to the controller memory. ➁ Press SETUP until A.rc appears in the display. ➂ Press any button on the remote control that is to be added. Press repeatedly until -.1.r or -.2.r appears in the controller display. The number 1 or 2 designates which remote is being added. If no number shows up after several attempts, clear the memory with the C.rc function (see below) and try again. Crc Clear Remote Control Used to clear all remote control information from the controller memory. ➁ Press SETUP until C.rc appears in the display. ➂ Press and together, and hold until the display goes blank. ➃ Proceed to A.rc, or exit setup mode. Cu.d Current Down Used to set the maximum current limit for downward movement. This is one of the safety features of the lift. When the controller senses the current limit you have set, it will stop its downward movement, reverse itself, and travel upward several inches. This feature only works when Electrical Current/Load Monitoring is displayed. (See also the section on Electrical Current/Load Monitoring below.) ➁ Press SETUP until Cu.d appears in the display. ➂ Press once. The last programmed current value appears in the display. ➃ Press or to change to the desired value. ➄ To confirm and lock in this value, press SETUP until the next available function appears, (in this case Cu.U). ➅ Exit setup mode. Cu.U Current Up Used to set the maximum current limit for upward movement. This feature only works when Electrical Current/Load Monitoring is displayed. (See also the section on Electrical Current/Load Monitoring below.) ➁ Press SETUP until Cu.U appears in the display. ➂ Press once. The last programmed current value appears in the display. ➃ Press or to change to the desired value. ➄ To confirm and lock in this value, press SETUP until the next available function appears, (in this case Cu.U). ➅ Exit setup mode.

5 Flatscreen Lift by Draper, Inc. page 5 of 6 Cou Count With this function, you can determine how many times the lift has been cycled (assuming the same lift and controller have been paired since new). A cycle is one complete lifting/lowering action. To see how many times the lift has been cycled, do the following: ➁ Press SETUP until Cou appears in the display. ➂ Pressing displays the number of cycles (up to 999). ➃ Pressing displays the number of cycles in thousands. ➄ Exit Setup mode. byp Bypass This is the temporary bypass mode. In this mode, the controller temporarily ignores all previously programmed instructions. IT ALSO IGNORES ALL THE PROGRAMMABLE SAFETY FUNCTIONS AND FEATURES. PLEASE EXERCISE CAUTION WHEN USING THIS FEATURE! The bypass feature may be used in special situations. For example, a programmed controller might be removed from a shorter lift model and then connected to a taller lift model. During operation of the taller lift, the lift may stop before reaching the bottom of its travel, because the controller is still programmed for the shorter lift, and assumes that it has already reached the bottom limit of travel for the shorter lift. To use the bypass feature, do the following: ➁ Press SETUP until byp appears in the display. ➂ Use or to move the lift up or down as desired. ➃ Exit Setup mode. Use this function to exit and lock the Setup mode, thereby preventing inadvertent changes to the settings or tampering by unauthorized persons. To exit Setup and lock access to the Setup mode: ➀ Press SETUP until appears in the display. ➁ Press to exit and lock the Setup mode. ELECTRICAL CURRENT/LOAD MONITORING One of the built-in safety features of the lift is based upon the fact that the harder the lift motor has to work, the more current it will draw. Should the lift encounter any unusual resistance during its travel, the current being drawn by the motor will increase rapidly. If there were no automatic means of cutting power to the motor, the result could be personal injury or damage to the motor or the lift. For this reason, the controller is designed to sense when the current being drawn exceeds a certain limit, and will instantly cut power to the motor, which immediately stops the lift. Please Note: This feature only works when Electrical Current/Load Monitoring is displayed. Monitoring the Current It is possible to monitor the current being drawn by the motor while the lift is in motion. Simply press SETUP while the lift is going up or down. The actual current being drawn by the lift will be shown (in amps) in real time on the controller display. This feature may also be used to detect gradual changes in current draw that could give an early indication of an impending internal mechanical failure (such failures are rare, but they can occur). Please Note: This feature must be on for Electrical Current/Load Monitoring to work. Setting the Current Limits Because the lift is designed to accommodate a wide variety of screens of various sizes and weights, it is important that the current limits be adjustable to the values appropriate to the weight of the screen being used. With this lift and controller, it is possible to set the upper current limit to any value desired within the normal operating range, which is 4.5 to 6.5 amps, depending on the weight of the screen. The reading should never exceed 8.0 amps, which is the factory default setting. To set the limit for upward travel: ➀ Run the lift up with the planned load. ➁ Monitor the current and note the maximum reading. ➂ Using the Current Up feature (see above), set the limit to 1 amp higher than the maximum reading noted. To set the limit for downward travel: ➃ Run the lift down with the planned load. ➄ Monitor the current and note the maximum reading. ➅ Using the Current Down feature (see above), set the limit to 1 amp higher than the maximum reading noted. Example: During upward travel, you note that the maximum reading is 3 amps. Use Current UP to set the limit at 4 amps. Please Note: This feature only works when Electrical Current/Load Monitoring is displayed. Plugging TV into Controller for Power TV can be plugged into outlet on Controller to power the TV. The outlet is fused to protect the TV from power surges. The outlet provides power only when the lift is fully up, and cuts power as soon as it starts going down. CC/12VT Port The Second RJ12 terminal from the left, marked CC/12VT, is a combined Contact Closure and 12 Volt Trigger port. Pin 4 Pin 3 Pin 2 Pin 1 Contact Closure uses pins 1,2,3,4 and works as follows: GND (COM) Up (closing pin 4 and 3 will make the lift go up) Down (closing pin 4 and 2 will make the lift go down) Stop (closing pin 1 and 4 will stop the lift) Contact Closure can be set up as a two- or three-button system if preferred. In a two-button system, Pin 1 is not used. The lift will stop if either the up or down buttons are pressed while the lift is in motion. Contact closure also works as either a momentary or permanent closure. 12 Volt trigger uses pins 5 and 6 and works as follows: Pin 5 Pin 6 DC 12V(+) DC 12V(-) The presence of voltage on pins 5 and 6 causes the lift to go up. No voltage on pins 5 and 6 causes the lift to go down. The range of acceptable DC voltage is 8V to 18V. Sensor Port (For Future Use) The RJ9 terminal on the right, marked EMERG. sensor port, is an extra sensor port. If desired, this terminal may be used with an additional external safety switch or sensor. Using an NC switch to close Pins 2 and 4 will disable the lift. When the contacts are opened, the lift will operate again. Pin 3 in this terminal may be used to supply 12VDC power to the external sensor if required. FCC Device: This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.

6 Flatscreen Lift by Draper, Inc. page 6 of 6 WARNING! RISK OF ELECTRICAL SHOCK DISCONNECT FROM POWER BEFORE SERVICING CC/Trig. port 1-CC stop, 2-CC dn 3-CC up, 4-GND 5-Trig. -in 12V(+) 6-Trig. -in 12V(-) LIFT Emerg. sensor port 2-in, V 4-GND CE Adapter Plug plugs in to back of 220V controller RJ12 RJ12 RJ9 Troubleshooting Info: A horizontal flashing bar in the lower left corner of the display tells you that the system assumes that it is in the lowest/closed position. If you find the bar flashing in the lower left corner and the lift is not in the lowest/closed position, use BYP function to bring the lift all the way down. (You may find yourself in this situation when Up and Down buttons on the controller are used without previously connecting controller to the lift.) A Horizontal flashing bar in the upper right corner of the display shows you that the lift has reached its maximum (previously programmed) extension height. Use EP function to set new desired height.

Model MC4 MEDIA CONTROL by OWI

Model MC4 MEDIA CONTROL by OWI Installation Instructions Model MC4 MEDIA CONTROL by OWI Media Control 4-Channel Mic/Line Audio Mixer in a two gang electrical box Established 1978 OWI Incorporated 17141 Kingsview Ave. Carson CA 90746

More information

DSP led gaming monitor USER MANUAL

DSP led gaming monitor USER MANUAL DSP24 24 led gaming monitor USER MANUAL INPUT VOLTAGE AC 100-240V - 50/60Hz DC12V 3A POWER INDICATOR LIGHT INDICATOR No light Green light Green light flash ODE Power off Normal work statement No signal

More information

USER MANUAL 6 Position Front Connect Rack for TD Series Modules with 16 Channel Modular Front Panel TDP

USER MANUAL 6 Position Front Connect Rack for TD Series Modules with 16 Channel Modular Front Panel TDP USER MANUAL 6 Position Front Connect Rack for TD Series Modules with 16 Channel Modular Front Panel TDP Warning for Your Protection 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings.

More information

Interactive Whiteboard. User Guide. Before operating the unit, please read this manual thoroughly, and retain it for future reference

Interactive Whiteboard. User Guide. Before operating the unit, please read this manual thoroughly, and retain it for future reference User Guide Before operating the unit, please read this manual thoroughly, and retain it for future reference Notice 1. When disconnecting the display from an electrical outlet, the plug must be pulled

More information

USER MANUAL 6 Position Powered Rack for TD Series Modules TDR 01 AC

USER MANUAL 6 Position Powered Rack for TD Series Modules TDR 01 AC USER MANUAL 6 Position Powered Rack for TD Series Modules TDR 01 AC Warning for Your Protection 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.

More information

Instruction Sheet. CFRD Series. High CFM Split Rear Doors

Instruction Sheet. CFRD Series. High CFM Split Rear Doors Instruction Sheet CFRD Series High CFM Split Rear Doors C UL R US LISTED NEW THANK YOU Thank you for purchasing the CFRD Seires High CFM Split Rear Doors. Please read these instructions thoroughly before

More information

NORTHSTAR 154 BATH/SPA TV. Installation Instructions

NORTHSTAR 154 BATH/SPA TV. Installation Instructions NORTHSTAR 154 BATH/SPA TV Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Must be installed by a qualified electrician Read these instructions. Keep these instructions for future use. Install in

More information

Plasma Display Electric Pop-Up Lift (PUL)

Plasma Display Electric Pop-Up Lift (PUL) I N S T R U C T I O N M A N U A L Plasma Display Electric Pop-Up Lift (PUL) Your is designed for installation in furniture or cabinets. Display mounting is made easy using the Q-latch mounting system and

More information

A100 Class D 100W Subwoofer Amplifier. User Guide VOLUME POWER BOOST

A100 Class D 100W Subwoofer Amplifier. User Guide VOLUME POWER BOOST A100 Class D 100W Subwoofer Amplifier User Guide VOLUME PHASE CROSSOVER POWER BOOST Important Safety Instructions Explanation of Graphical Symbols RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOQUE ÉLECTRIQUE

More information

100 Watt Power Amp 50 Watts x 50 Watts Single Rack Space

100 Watt Power Amp 50 Watts x 50 Watts Single Rack Space User's Manual 100 Watt Power Amp 50 Watts x 50 Watts Single Rack Space 1 Introduction Congratulations on your purchase of the Rocktron Velocity 100LTD power amplifier! The Velocity 100LTD was designed

More information

LOUDSPEAKER OWNER'S MANUAL

LOUDSPEAKER OWNER'S MANUAL CDT ARCHITECTURAL LOUDSPEAKER OWNER'S MANUAL ARCHITECTURAL SPEAKERS IMPORTANT SAFETY INSTRUCTIONS 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions.

More information

INSTALLATION MANUAL. Recessed In-Ceiling Motorized Projection Screen

INSTALLATION MANUAL. Recessed In-Ceiling Motorized Projection Screen INSTALLATION MANUAL Recessed In-Ceiling Motorized Projection Screen IMPORTANT: BEFORE YOU BEGIN To avoid staining or scratching the screen, wash your hands and clean the work area before starting. Do not

More information

LSL PF - Lift System Light Push Flap

LSL PF - Lift System Light Push Flap Installation Instructions LSL PF - Lift System Light Push Flap Design Highlights -Quiet Smooth Action at Approximately 40mm [1.6 ] per Second -Full Cable Management -Wide Range of Mounting Options -24V

More information

PM - Projector Mount System

PM - Projector Mount System Installation Instructions PM - Projector Mount System Design Highlights -Beautiful Anodised Aluminium Finish -Complete Lead-Screw Adjustment of All Pitches of Angle -Range of Fixed and Telescopic Poles

More information

UBL - Under Bed Lift. Installation Instructions. Thank you for choosing futureautomation. Lift Mechanisms

UBL - Under Bed Lift. Installation Instructions. Thank you for choosing futureautomation. Lift Mechanisms Installation Instructions UBL - Under Bed Lift Design Highlights -Near Silent Operation -Full Cable Management -Programmable Viewing Height -Wide Range of Screen Mounting Options -Innovative Design Lift

More information

DC IN 18V 3A. User Manual EUROPORT EPA Watt Handheld PA System with Microphone and Rechargeable Battery

DC IN 18V 3A. User Manual EUROPORT EPA Watt Handheld PA System with Microphone and Rechargeable Battery DC IN 18V 3A User Manual EUROPORT EPA40 40-Watt Handheld PA System with Microphone and Rechargeable Battery 2 EUROPORT EPA40 User Manual Table of Contents Thank you...2 Important Safety Instructions...3

More information

REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.

REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. operator's MaNUal Cat. No. C12-28 DCR Job Site Radio TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. Read these instructions. Keeps these instructions. Heed all warnings.

More information

LSM PF - Lift System Medium Push Flap

LSM PF - Lift System Medium Push Flap Installation Instructions LSM PF - Lift System Medium Push Flap Design Highlights -Quiet Smooth Action at Approximately 40mm [1.6 ] per Second -Full Cable Management -Wide Range of Mounting Options -24V

More information

Owner s Manual. OutCast 1.2. The Ultimate Outdoor Speaker System

Owner s Manual. OutCast 1.2. The Ultimate Outdoor Speaker System Owner s Manual OutCast 1.2 The Ultimate Outdoor Speaker System Safety Guidelines IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ THESE INSTRUCTIONS GIVEN IN THIS MANUAL AND THOSE MARKED ON THE UNIT.

More information

THE ROCK PROFESSIONAL 2 WAY ACTIVE STUDIO MONITOR

THE ROCK PROFESSIONAL 2 WAY ACTIVE STUDIO MONITOR THE ROCK PROFESSIONAL 2 WAY ACTIVE STUDIO MONITOR Owner's manual 1 THANK YOU! Thank you for buying the Unity Audio THE ROCK, one of the most accurate 2 way active studio monitors available. We wish you

More information

LSL EFA - Lift System Light Electric Flap Actuator

LSL EFA - Lift System Light Electric Flap Actuator Installation Instructions LSL EFA - Lift System Light Electric Flap Actuator Design Highlights -Quiet Smooth Action at Approximately 40mm [1.6 ] per Second -Full Cable Management -Wide Range of Mounting

More information

The Rock MK II. Owner's manual PROFESSIONAL 2 WAY ACTIVE STUDIO MONITOR. v1212. v0312

The Rock MK II. Owner's manual PROFESSIONAL 2 WAY ACTIVE STUDIO MONITOR. v1212. v0312 The Rock MK II PROFESSIONAL 2 WAY ACTIVE STUDIO MONITOR Owner's manual The Rock MK IIUser UserManual Manual THE ROCK 11 v1212 v0312 THANK YOU! Thank you for buying the Unity Audio THE ROCK, one of the

More information

ASSEMBLY & USE INSTRUCTIONS

ASSEMBLY & USE INSTRUCTIONS ASSEMBLY & USE INSTRUCTIONS SKU# 1001777085 7FT to 10FT LED Pre-Lit Rising Artificial Spruce Tree IMPORTANT SAFETY WARNINGS 1.Read these instructions before using this product. 2.Save these instructions

More information

Installation Instructions LSM TU EFA - Lift System Medium Telescopic Unit Electric Flap Actuator

Installation Instructions LSM TU EFA - Lift System Medium Telescopic Unit Electric Flap Actuator Installation Instructions LSM TU EFA - Lift System Medium Telescopic Unit Electric Flap Actuator Design Highlights -Quiet Smooth Action at Approximately 40mm [1.6 ] per Second -Full Cable Management -Wide

More information

A B C D E F. Tools Required (supplied by others)

A B C D E F. Tools Required (supplied by others) Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)

More information

TV Lift System Model L-75i Installation Instructions

TV Lift System Model L-75i Installation Instructions TV Lift System Model L-75i Installation Instructions Below is a parts list describing all of the items included with the Model L-75i Lift System. Contact: Support@Nexus21.com Toll Free: (866) 500-5438

More information

WIRELESS TRI-JACK WIRELESS REMOTE KIT COMPONENTS LITERATURE NUMBER REV. C WARNING EXPLOSION WARNING PERSONAL INJURY & PROPERTY DAMAGE

WIRELESS TRI-JACK WIRELESS REMOTE KIT COMPONENTS LITERATURE NUMBER REV. C WARNING EXPLOSION WARNING PERSONAL INJURY & PROPERTY DAMAGE LITERATURE NUMBER 8260. REV. C WIRELESS TRI-JACK Effective July 207 Installation Operation Maintenance SAFETY ALERT SYMBOLS Safety Symbols alerting you to potential personal safety hazards. Obey all safety

More information

CANARY AUDIO. Vacuum Tube Preamplifier CA-800 OWNER S MANUAL. Handcrafted in California MADE IN USA

CANARY AUDIO. Vacuum Tube Preamplifier CA-800 OWNER S MANUAL. Handcrafted in California MADE IN USA CANARY AUDIO Vacuum Tube Preamplifier Handcrafted in California CA-800 OWNER S MANUAL MADE IN USA Dear Customer: Please allow us to take this opportunity to thank you for purchasing this CANARY AUDIO product.

More information

WIRELESS CAMPER JACK LITERATURE NUMBER REV. C CCD WARNING PERSONAL INJURY & PROPERTY DAMAGE WARNING EXPLOSION. Effective NOV 2018

WIRELESS CAMPER JACK LITERATURE NUMBER REV. C CCD WARNING PERSONAL INJURY & PROPERTY DAMAGE WARNING EXPLOSION. Effective NOV 2018 LITERATURE NUMBER 670903. REV. C WIRELESS CAMPER JACK Effective NOV 2018 Installation Operation Maintenance SAFETY ALERT SYMBOLS Safety Symbols alerting you to potential personal safety hazards. Obey all

More information

LED Recessed Troffer Retrofit Kit

LED Recessed Troffer Retrofit Kit Model # TRK series LED Recessed Troffer Retrofit Kit Installation Instructions PACKAGE CONTENTS A B E Part Item Name Qty. A Retrofit assembly 1 B Bracket 2 C Sheet metal screw 4 D Wire nuts 5 E Gap channel

More information

02OWNER S MANUAL 06 TROUBLESHOOTING 08LIMITED WARRANTY

02OWNER S MANUAL 06 TROUBLESHOOTING 08LIMITED WARRANTY 02OWNER S MANUAL 06 TROUBLESHOOTING 08LIMITED WARRANTY Owner s manual Introduction Thank you for choosing Scansonic loudspeakers, we hope they will bring you many years of enjoyment. Please read this manual

More information

CANARY AUDIO CA-400. Vacuum Tube MM/MC Phono Preamplifier OWNER S MANUAL. Handcrafted in California MADE IN USA

CANARY AUDIO CA-400. Vacuum Tube MM/MC Phono Preamplifier OWNER S MANUAL. Handcrafted in California MADE IN USA CANARY AUDIO Vacuum Tube MM/MC Phono Preamplifier Handcrafted in California CA-400 OWNER S MANUAL MADE IN USA Dear Customer: Please allow us to take this opportunity to thank you for purchasing this CANARY

More information

Down and Out Motor Mount Assembly & Installation Directions

Down and Out Motor Mount Assembly & Installation Directions Down and Out Motor Mount Assembly & Installation Directions Mounting the Down and Out Motor Mount correctly takes a lot of thought and a lot of planning. Please read the directions thoroughly and plan

More information

4070 Subwoofer Owners' Manual

4070 Subwoofer Owners' Manual 4070 Subwoofer Owners' Manual Introduction Contents Congratulations on purchasing this Gale 4070 subwoofer. To ensure optimum performance please read and retain this manual, then sit back, relax and enjoy!

More information

A B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver

A B C D E F. b.tools Required (supplied by others) 3/16 Drill Bit 3/8 Wrench Phillips Head Screwdriver Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover

More information

Installation Instructions Studio Makeup Station

Installation Instructions Studio Makeup Station Installation Instructions Studio Makeup Station 30" and 36" Models 5-light 30" Studio Makeup Station 8-light 30" Studio Makeup Station 6-light 36" Studio Makeup Station 9-light 36" Studio Makeup Station

More information

Plasma Display Electric Ceiling Lifts

Plasma Display Electric Ceiling Lifts I N S T R U C T I O N M A N U A L The Plasma Display Electric Ceiling Lift is designed for plasma displays requiring an extended drop (18 to 42 inches) from their hidden location. The lift is designed

More information

IEDA524-H / IEDA520DTB DIGITAL MICROPHONE STATION. Installation Instructions

IEDA524-H / IEDA520DTB DIGITAL MICROPHONE STATION. Installation Instructions IEDA524-H / IED0520DTB DIGITAL MICROPHONE STATION Installation Instructions REV: 12-12 DOC: 369B INSTALLATION INSTRUCTIONS INTRODUCTION Description The IED 524 digital microphone station is a 4-button

More information

MicroPod Sub User manual / Bedienungsanleitung / Manual del Usario

MicroPod Sub User manual / Bedienungsanleitung / Manual del Usario PODSPEAKERS by Scandyna MicroPod Sub User manual / Bedienungsanleitung / Manual del Usario CONGRATULATIONS! on the purchase of your new MicroPod Sub from Scandyna Thank you for choosing MicroPod Sub from

More information

PD2.5 - Projector Drop Mechanism

PD2.5 - Projector Drop Mechanism Installation Instructions PD2.5 - Projector Drop Mechanism Design Highlights -Outputs for 3rd Party Product Control -Cassette Housing for Ease of Installation -Full Cable Management -Tilt Function -Range

More information

Thunder Power Tarp Kit Operation. Dual Arm Curb Side Stowing Single Arm Curb Side Stowing Flex Arm Curb Side Stowing.

Thunder Power Tarp Kit Operation. Dual Arm Curb Side Stowing Single Arm Curb Side Stowing Flex Arm Curb Side Stowing. Thunder Power Tarp Kit Operation Dual Arm Curb Side Stowing Single Arm Curb Side Stowing Flex Arm Curb Side Stowing 011-52475 Rev - 2 P a g e USE THE PROCEDURES BELOW TO OPERATE THE TARP SYSTEM Powering

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS CLASSIC EDITION WITH AUX-IN CHROME OR BLACK FINISH THANK YOU FOR CHOOSING STEEL HORSE AUDIO! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions,

More information

AD1240 Champion Series Outdoor, Medium Duty Pan/Tilt

AD1240 Champion Series Outdoor, Medium Duty Pan/Tilt AD1240 Champion Series Outdoor, Medium Duty Pan/Tilt Installation and Operating Instructions This manual describes the installation and operating procedures for the American Dynamics AD1240 Champion Series

More information

MPS14 Rack Mount Power Supply

MPS14 Rack Mount Power Supply MPS14 Rack Mount Power Supply USER GUIDE Publication AP3898 Limited One Year Warranty This product has been manufactured in the UK by ALLEN & HEATH and is warranted to be free from defects in materials

More information

7.5 FT PRE-LIT ENGLEWOOD PINE TREE

7.5 FT PRE-LIT ENGLEWOOD PINE TREE ITEM #0243778 7.5 FT PRE-LIT ENGLEWOOD PINE TREE Holiday Living & Design is a registered trademark of LF, LLC. All Rights Reserved. MODEL #W14L030 Español p. 11 ATTACH YOUR RECEIPT HERE Serial Number Purchase

More information

Alliance Towel Dispensing System. Operation Manual

Alliance Towel Dispensing System. Operation Manual Alliance Towel Dispensing System Operation Manual Alliance Towel Dispensing System Table of Contents Safety Information... page 2 Mounting Instructions... page 3 Towel Loading Instructions... page 7 Settings...

More information

Rack Mount Power Supplies

Rack Mount Power Supplies Rack Mount Power Supplies Installation Guide Models Include: Vertiline3D - 12VDC @ 8 amp - Eight (8) PTC protected outputs Vertiline6D - 24VDC @ 8 amp - Eight (8) PTC protected outputs Rev. 090710 More

More information

HD 7700 Setup & Operator Manual

HD 7700 Setup & Operator Manual HD 7700 Setup & Operator Manual Issue 1 December, 01 Performance Design Inc. The Heavy Duty Ultima (HD 7700) electric punch has been designed to punch most any job that may pass through your bindery or

More information

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market 1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter

More information

Enclosure for AMP1 Series Energy Meters with Swing Panel Kit

Enclosure for AMP1 Series Energy Meters with Swing Panel Kit GE Industrial Solutions DET-809 Installation Instructions AMP1N4 Enclosure for AMP1 Series Energy Meters with Swing Panel Kit Safety FCC PART 15 INFORMATION NOTE: This equipment has been tested by the

More information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 7.5 Swift Lock Ready Shape Tree (Patent Pending) Instructions IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND

More information

Have a Bright Day! Nicholas Harmon President and CEO

Have a Bright Day! Nicholas Harmon President and CEO VD07 Dear Customer, Thank you for purchasing the Verilux Modern Deluxe Natural Spectrum Desk Lamp. You have received an innovative and quality manufactured product, backed by a one-year limited warranty.

More information

Thunder Power Tarp Kit Operation

Thunder Power Tarp Kit Operation Thunder Power Tarp Kit Operation Dual Arm Curb Side Stowing Single Arm Curb Side Stowing 011-52476 Rev. H P a g e 2 In this booklet you will find: OPERATING INSTRUCTIONS... 3 Powering up or down the system...

More information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 5 Swift Lock Ready Shape Tree (Patent Pending) Instructions IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW

More information

Auto-Lift Operating System

Auto-Lift Operating System Installation Instructions Parasol Cellular Shades Auto-Lift Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 STEP 1

More information

Plasma Dual Swing-Out (PDS Series) Wall Mount

Plasma Dual Swing-Out (PDS Series) Wall Mount INSTALLATION INSTRUCTIONS Plasma Dual Swing-Out ( Series) Wall Mount The wall mount is a rugged, versatile, and installer-friendly solution to unique display mounting requirements. In addition to providing

More information

Important safety Instructions CUTION: Before you begin any of the Installation procedures on page 3, read and follow the warnings and safety instructi

Important safety Instructions CUTION: Before you begin any of the Installation procedures on page 3, read and follow the warnings and safety instructi Mounting Instructions Item No.: 421.68.440 TV Lift Parts included with your TV Lift Lift unit (#1 ) Power supply + bracket (#2 ) R.F. Module (#3 ) Rocker switch (#4 ) Remote Control (not shown) Plasma

More information

Have a Bright Day! Nicholas Harmon President and CEO

Have a Bright Day! Nicholas Harmon President and CEO VD09 Dear Customer, Thank you for purchasing the Verilux Woodbury Deluxe Natural Spectrum Desk and Table Lamp. You have received an innovative and quality manufactured product, backed by a oneyear limited

More information

28BSST POWER AMPLIFIER OWNER S MANUAL UPDATED

28BSST POWER AMPLIFIER OWNER S MANUAL UPDATED 28BSST POWER AMPLIFIER OWNER S MANUAL UPDATED 2006-12-01 Table of Contents General Introduction Page 1 Description Installation and Ventilation Rear Panel Input Settings/Connections Page 2 Setting Input

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions

More information

Mini Multimeter with Non-Contact Voltage Detector (NCV)

Mini Multimeter with Non-Contact Voltage Detector (NCV) Owner s Manual Mini Multimeter with Non-Contact Voltage Detector (NCV) Model No. 82314 CAUTION: Read, understand and follow Safety Rules and Operating Instructions in this manual before using this product.

More information

REVERIE ADJUSTABLE BED OWNER S MANUAL. Reverie Deluxe Adjustable Bed. Copyright All Rights Reserved. Manual Part No.

REVERIE ADJUSTABLE BED OWNER S MANUAL. Reverie Deluxe Adjustable Bed. Copyright All Rights Reserved. Manual Part No. REVERIE ADJUSTABLE BED OWNER S MANUAL Reverie Deluxe Adjustable Bed REV: 2-25-09 Manual Part No. A-AB-A18-WWM3-C Copyright 2009. All Rights Reserved Ascion LLC. TABLE OF CONTENTS Safety Precautions...

More information

k EDR /11. S cape OWNERS MANUAL. S cape Platform. Silhouette. Pro-motion. Bronze. [ power foundations ]

k EDR /11. S cape OWNERS MANUAL. S cape Platform. Silhouette. Pro-motion. Bronze. [ power foundations ] 99300787-k EDR11739 4/11 OWNERS MANUAL S cape S cape Platform Silhouette Pro-motion Bronze [ power foundations ] contents Advisory... 3 Acoustics... 5 Installation... 6 Turnbuckle Adjustment... 18 Troubleshooting...

More information

SlimRack Bed Lift System OEM INSTALLATION MANUAL

SlimRack Bed Lift System OEM INSTALLATION MANUAL SlimRack Bed Lift System OEM INSTALLATION MANUAL Rev: 07.11.2018 TABLE OF CONTENTS System Information 2 Safety Information 3 Resources Required 3 General Requirements 3 Installation 4 SlimRack Bed Lift

More information

EXTRA LARGE OUTDOOR HOUSINGS

EXTRA LARGE OUTDOOR HOUSINGS EXTRA LARGE OUTDOOR HOUSINGS ws Camera Spacer Heater Rails Bushing Power Cable Screw Ground Wire Terminal Lug HS9386 SERIES M4 Captive Screws I N STALLATION AND O P E R A TING I N STRU CTIONS W W W. AIG

More information

User Guide. Model No.: GDI-GFD7200

User Guide. Model No.: GDI-GFD7200 User Guide Model No.: GDI-GFD7200 2 Important Safety Instructions and Warnings Please read before installation WARNING: CAUTION: To reduce the risk of fire or electrical shock, do not expose the product

More information

PL - Plasma Lift. Installation Instructions. Thank you for choosing futureautomation

PL - Plasma Lift. Installation Instructions. Thank you for choosing futureautomation Installation Instructions PL - Plasma Lift Design Highlights -Unique Drop and Roll Flap Mechanism -Hand Made Quality Construction -Full Cable Management -Custom Sized to Suit Exact Size of Screen Lift

More information

Cordless Make Up Mirror WITH ILLUMINATED 1X AND 10X MAGNIFICATION PLUS NIGHT LIGHT

Cordless Make Up Mirror WITH ILLUMINATED 1X AND 10X MAGNIFICATION PLUS NIGHT LIGHT Cordless Make Up Mirror WITH ILLUMINATED 1X AND 10X MAGNIFICATION PLUS NIGHT LIGHT TABLE OF CONTENTS Warnings and Cautions....1 Location of Parts and Controls....6 Installing the Batteries...8 Using the

More information

Sylvania 9 Color Changing One Plug Tree Tree ID # T5, Item # V

Sylvania 9 Color Changing One Plug Tree Tree ID # T5, Item # V Sylvania 9 Color Changing One Plug Tree Tree ID # T5, Item # V66354-13 Thank you for purchasing this tree. This tree assembles in minutes and is decorated with 600 LED lights. This tree has 8 lighting

More information

User Manual Subwoofer Module DS 2.0 Hypex DS - Series

User Manual Subwoofer Module DS 2.0 Hypex DS - Series Hypex Electronics BV Kattegat 8 9723 JP Groningen, The Netherlands +31 50 526 4993 info@hypex.nl User Manual Subwoofer Module DS 2.0 Hypex DS - Series General safety instructions 3 Introduction..... 4

More information

Mini-Z. Manual. Model: ZA-21.

Mini-Z. Manual. Model: ZA-21. Mini-Z Manual Model: ZA-21 www.drzamps.com This symbol advises the user to read all accompanying literature for safely operating the unit Important Safety Instructions 1) Read these instructions. 2) Keep

More information

ONE TOUCH CONTROL BOX

ONE TOUCH CONTROL BOX ONE TOUCH CONTROL BOX CONVERSION KIT INSTRUCTIONS REMOVAL, INSTALLATION, OPERATION, AND REMOTE CONTROL PROGRAMMING THUNDERSTONE PART #101322 REVISION A JULY 14 TH 2016 2 P a g e INSTALLING THE THUNDER

More information

GAS CYLINDER LIFTS BEFORE YOU BEGIN

GAS CYLINDER LIFTS BEFORE YOU BEGIN I N S T R U C T I O N M A N U A L GAS CYLINDER LIFTS The LM Series gas cylinder lifts are smooth, quiet reliable lift mechanisms for your valuable equipment in a mobile application. The LM Series can be

More information

CHUBBSAFES EVOLVE INSTRUCTION MANUAL

CHUBBSAFES EVOLVE INSTRUCTION MANUAL CHUBBSAFES EVOLVE INSTRUCTION MANUAL 1 Ref: BASS-0010-B/21.02.2014 Table of content 1- CHARACTERISTICS... 4 1-1 Models... 4 1-2 Dimensions & Weights... 4 1-3 Interior fittings (standard and optional)...

More information

Gold Luxury-Lift. la-z-boy.com. operating instructions. instrucciones de operación. instructions. power recliner.

Gold Luxury-Lift. la-z-boy.com. operating instructions. instrucciones de operación. instructions. power recliner. operating instructions instrucciones de operación instructions Gold Luxury-Lift power recliner Sillón reclinable la-z-boy.com fauteuil inclinable ÉlectroPlus La-Z-Boy Incorporated One La-Z-Boy Drive Monroe,

More information

Clutch Operated FlexShade NEXD Window shade with heavy duty clutch and 3 hardware profile. Cassette option.

Clutch Operated FlexShade NEXD Window shade with heavy duty clutch and 3 hardware profile. Cassette option. INSTRUCTIONS INSTALLATION & OPERATION Overview - FlexShade Components Idler 1¼ Roller with Spline Atachment Clutch TOOLS REQUIRED Clutch PENCIL POWER DRILL Idler 1 Eliptical Hem Bar TAPE MEASURE LEVEL

More information

OWNERS MANUAL. Gold Series

OWNERS MANUAL. Gold Series LUNAR OWNERS MANUAL Comfort Base Gold Series Contents Safety Information...3 What Is Included...6 Assembly - Base...7 Location of Controls - Remote...11 Operation - Main...11 Operation - Linking the Remote...12

More information

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

More information

THIS PRODUCT IS FOR PROFESSIONAL LABORATORY USE ONLY USER'S MANUAL. WELLS ENGINE UNIT 230 VOLT Product No. U905, U906, U907, U908

THIS PRODUCT IS FOR PROFESSIONAL LABORATORY USE ONLY USER'S MANUAL. WELLS ENGINE UNIT 230 VOLT Product No. U905, U906, U907, U908 DENTAL, INC. TECHNICAL BULLETIN U807-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE THIS PRODUCT IS

More information

Installation Instructions

Installation Instructions Installation Instructions Speedcook Oven Read carefully. Keep these Instructions. INSTALLATION INSTRUCTIONS Electrical Requirements Product rating is 240/208 volts AC, 60 Hertz, 30 amps and 6.5 kilowatts.

More information

CCTV Rack Mount Power Supplies

CCTV Rack Mount Power Supplies CCTV Rack Mount Power Supplies Installation Guide Models Include: Vertiline16 - or @ 10A - Sixteen (16) fuse protected outputs Vertiline166 - or @ 14A - Sixteen (16) fuse protected outputs Vertiline16D

More information

230V AC Scissor Lift SLX Video Projector Lift by Draper

230V AC Scissor Lift SLX Video Projector Lift by Draper Installation/Operating Instructions 20V AC Scissor Lift SLX Video Projector Lift by Draper These Installation/Operating Instructions are available in the official language of the country where you purchase

More information

SBC450 SBC850 IMPORTANT SAFETY INSTRUCTIONS. 4- and 8-Bay Networked Charging. Stations. Download PDF. English. Table of Contents

SBC450 SBC850 IMPORTANT SAFETY INSTRUCTIONS. 4- and 8-Bay Networked Charging. Stations. Download PDF. English. Table of Contents Publications User Guides SBC450-850 (English) Download PDF English Table of Contents IMPORTANT SAFETY INSTRUCTIONS SBC450 and SBC850 Networked Charging Stations Included Components Charger Controls and

More information

CCTV Rack Mount Power Supplies

CCTV Rack Mount Power Supplies CCTV Rack Mount Power Supplies Installation Guide Models Include: Vertiline24C Vertiline24CD - or @ 10 - or @ 10 - Twenty-four (24) fuse protected outputs - Twenty-four (24) PTC protected outputs Vertiline246C

More information

Sliding Gate Operator User's Manual

Sliding Gate Operator User's Manual Sliding Gate Operator User's Manual SL600AC. Products introduction Please read the instructions carefully before proceeding. MCU is supplied to control the gate operator. Keypad / single button interface.

More information

Pump Sentry. Models 812 PS & 1612 PS INSTALLATION INSTRUCTIONS

Pump Sentry. Models 812 PS & 1612 PS INSTALLATION INSTRUCTIONS Pump Sentry Models 812 PS & 1612 PS INSTALLATION INSTRUCTIONS The Pump Sentry is an innovative power station designed to operate your pump during a power outage. When properly installed, it will provide

More information

TECHNICAL SPECIFICATIONS. CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules devices HKPY2VC/A 3 modules devices

TECHNICAL SPECIFICATIONS. CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules devices HKPY2VC/A 3 modules devices USER GUIDE Mobility MiX Cart HKPX2VC/A Mobility MiX Cart 30 HKPY2VC/A Mobility MiX Cart 45 TECHNICAL SPECIFICATIONS CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules 30 24 20 devices HKPY2VC/A

More information

TC26-B Vehicle Sensor

TC26-B Vehicle Sensor Section 1 General Description The Model TC26-B is a microprocessor controlled vehicle sensor with a variable range. It is designed to trigger the operation of a traffic controller. The TC26-B will only

More information

Covers All 430, 440, 441 and CJ Series Advanced Security Systems.

Covers All 430, 440, 441 and CJ Series Advanced Security Systems. INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with

More information

Instruction Manual LongArm ABL3 Remote Operator for Medium Voltage Allen-Bradley Centerline** Motor Control Center Units

Instruction Manual LongArm ABL3 Remote Operator for Medium Voltage Allen-Bradley Centerline** Motor Control Center Units Instruction Manual LongArm ABL3 Remote Operator for Medium Voltage Allen-Bradley Centerline** Motor Control Center Units Model: ABL3-C and ABL3-W US Patent 9,666,384 ** LongArm is a trademark of MarTek

More information

Thunder Power Tarp Kit Operation Guide

Thunder Power Tarp Kit Operation Guide Thunder Power Tarp Kit Operation Guide Dual Arm Curb Side Stowing Single Arm Curb Side Stowing Flex Arm Curb Side Stowing REV - B 1/13/17 2 P a g e USE THE PROCEDURES BELOW TO OPERATE THE TARP SYSTEM Powering

More information

CHECKLIST & COMPONENTS

CHECKLIST & COMPONENTS Eclipse Compact www.rollershuttercompany.com Tel 0800 6444121 55mm Roller Garage Doors CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape measure Power drill 10mm A/F

More information

DeSoto NEMA 4X EMERGENCY LIGHTING UNIT. U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 INSTALLATION INSTRUCTIONS

DeSoto NEMA 4X EMERGENCY LIGHTING UNIT. U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 INSTALLATION INSTRUCTIONS DeSoto U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 NEMA 4X EMERGENCY LIGHTING UNIT INSTALLATION INSTRUCTIONS U.S. Patent No.s 6,135,624; 6,193,395; 6,502,044 B1; D505,222; IMPORTANT

More information

LIPPERTCOMPONENTS, INC.

LIPPERTCOMPONENTS, INC. LIPPERTCOMPONENTS, INC. SCHWINTEK INWALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL Contents I. Controls 1-1 System components 1 1-1A versions C1 & C2 2 1-2 Motor wiring harness connections 3 1-3 Extend

More information

FOR INDOOR/SEASONAL USE ONLY

FOR INDOOR/SEASONAL USE ONLY 9' Warm White /Multi LED Color Changing One Plug Tree V66362-60 INSTRUCTION MANUAL Thank you for purchasing a SYLVANIA Pre-lighted Tree. This tree assembles in minutes and is decorated with energy saving

More information

Sliding Gate Operator User's Manual

Sliding Gate Operator User's Manual Sliding Gate Operator User's Manual PY800AC/PY00AC. Products introduction Please read the instructions carefully before proceeding. MCU is supplied to control the gate operator. Keypad / single button

More information

CONTENTS: 5740AH - 40 Ton Air/Hydraulic Shop Press 5750AH - 50 Ton Air/Hydraulic Shop Press OWNER'S MANUAL

CONTENTS: 5740AH - 40 Ton Air/Hydraulic Shop Press 5750AH - 50 Ton Air/Hydraulic Shop Press OWNER'S MANUAL OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Safety Information and Warranty Information 3 Parts List 4-6 Assembly Instructions 7 Pump and Ram Assembly Instructions 8 Procedure for Bleeding Air 9 Pump

More information

Installer Guide smart connect

Installer Guide smart connect Installer Guide smart connect TM 7490 Wireless Remote Outdoor Sensor Please read all instructions before proceeding. The wireless remote outdoor sensor monitors temperature at a remote outdoor location

More information

Dear Customer, User Memo: Please visit us on facebook or twitter! Thank you for purchasing this product.

Dear Customer, User Memo: Please visit us on facebook or twitter! Thank you for purchasing this product. Owner s Manual 1 Dear Customer, Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. User Memo: Date of purchase: Dealer name: Dealer address:

More information

Electrical TV Lift mechanism TS750. Parts included with your TV Lift

Electrical TV Lift mechanism TS750. Parts included with your TV Lift Electrical TV Lift mechanism TS750 Parts included with your TV Lift Lift unit ( #1 ) Power supply + bracket ( #2 ) R.F. Module ( #3 ) Rocker switch ( #4 ) Remote Control (not shown) Plasma screen brackets

More information