NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009

Size: px
Start display at page:

Download "NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009"

Transcription

1 NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 SUBJECT: CAMSHAFT AND ROCKER SHAFT ASSEMBLIES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0050 DD Camshaft and Rocker Shaft Assemblies The Camshaft and Rocker Shaft Assemblies Section of the DD13 Workshop Manual is revised DDC-SVC-MAN-0050 DD Engine Brake The Engine Brake Section of the DD13 Workshop Manual is revised NOTE: Page numbers are based on the most recent version of the individual publication and may be adjusted throughout the annual print cycle. Table 1

2 CAMSHAFT AND ROCKER SHAFT ASSEMBLIES The engine uses a dual overhead camshaft and rocker shaft design. The intake and exhaust camshafts must be timed to each other and also timed to the crankshaft. The timing is accomplished through the geartrain. The engine uses an integral engine brake. Engine braking is controlled electronically by the engine control system with an electric solenoid. When activated, the solenoid allows oil pressure to activate a piston on the exhaust rocker arm. Engine braking is accomplished with a single exhaust valve in each cylinder. The exhaust camshaft uses a separate engine brake-only lobe that allows for double valve activation for high efficiency braking. The exhaust valve is firstoperatedtowardthecompletionof the intake stroke, closed during the compression stroke and opened a second time when the compression stroke is completed. CAMSHAFT AND ROCKER SHAFT ASSEMBLIES REMOVAL Remove as follows: 1. Turn engine OFF, (key OFF, engine OFF). 2. Steam clean the engine. 3. Disconnect the battery power to the engine. 4. Remove the air cleaner and the turbocharger inlet pipe and hose. 5. Remove air cleaner housing. 6. Remove eight bolts from air cleaner bracket and remove bracket. 7. Remove nineteen bolts from rocker cover and remove rocker cover. 8. Remove the two injector harness connectors from the intermediate cam frame. NOTE: TDC can be confirmed by installing front camshaft timing tool (W ). 9. Rotate the engine to top dead center (TDC) on cylinder No. 1 using engine barring tool (J-46392). 10. Remove the crankshaft position sensor (CKP) from the rear of the flywheel housing.

3 11. Install flywheel housing crankshaft locking tool (W ) into the CKP sensor hole located in the rear of the flywheel housing. The plastic tip protrudes into the cutout in the tone wheel to accurately locate TDC. NOTICE: Ensure when loosening the rocker shaft bolts that the bolts are loosened from the inside bolts outward in 1/2 turn increments. The increment procedure needs to be followed to prevent the rocker shaft from breaking. 12. Completely loosen all of the adjusting screws on all of the rocker arms. 13. Loosen the seven bolts securing the intake rocker shaft to the camshaft caps. 14. Using intake rocker arm lifter and spacer tool (W ), remove the intake rocker shaft assembly. 15. Loosen the seven bolts securing the exhaust rocker shaft to the camshaft caps.

4 16. Using exhaust rocker arm lifter and spacer tool (W ), remove the exhaust rocker shaft assembly. NOTE: The engine brake solenoids do not have to be removed unless damaged. 17. Remove the remaining bolts from the camshaft caps and remove with cam bearing cap puller (J 48883). 18. Remove the intake and exhaust camshaft assemblies from the camshaft housing INSPECTION OF THE CAMSHAFT AND ROCKER SHAFT ASSEMBLIES Inspect the camshaft and rocker shaft assemblies as follows: 1. Inspect the camshafts for lobe damage; replace if necessary. 2. Inspect the camshaft gears for damage; replace if necessary. 3. Inspect the rocker shaft for scoring or scuffing; replace if necessary. 4. Inspect rocker arms for roller and bushing damage; replace if necessary. 5. Inspect adjusting screws and buttons; replace if necessary. 6. Inspect cam caps and cam journals in cam frame for damage; replace if necessary. 7. Inspect the tone wheel on the intake camshaft for cracks, bending or any damage. If damage is found, replace the intake camshaft.

5 1.4.2 INSTALLATION OF THE CAMSHAFT AND ROCKER SHAFT ASSEMBLIES Install as follows: 1. Verify that the crankshaft is at top dead center (TDC) on cylinder number one using crankshaft locking tool (W ) installed in crankshaft position sensor (CKP) hole located in the flywheel housing. 2. Install camshaft timing tool (W ) (1) to the rear of the camshaft housing. Tighten the two bolts.

6 3. Locate the etched triangle on the camshaft gear teeth and mark the teeth with a paint pen. 4. Lubricate the lower camshaft bearing surfaces and camshaft journals before installing the camshafts. Install the exhaust and intake camshaft gear assemblies into the cam frame. 5. Align the marked gear teeth with the marks on the timing tool. 6. Install camshaft timing tool (W ) (1) to the front of the camshaft frame and into the grooves cut into the camshafts. Secure timing tool to the camshaft with a bolt. [a] At this point the front timing tool should slide into the camshaft grooves easily with no drag. [b] If there is excessive drag when installing the tool, the camshafts are out of time. 7. Verify that the marks on the gear teeth match the marks on the timing tool. NOTICE The camshaft caps are numbered and need to be installed correctly.

7 8. Install the seven camshaft caps onto intake and exhaust camshafts. 9. The first and seventh camshaft caps hold the engine brake solenoid to camshaft cap. Replace the O-rings on the solenoid prior to reinstallation. Install the engine brake solenoid. NOTE: There are 30 bolts retaining the camshaft assemblies; mm (M10) bolts, seven 108 mm (M10) bolts and nine 63 mm (M8) bolts. 10. Install the 30 bolts to camshaft caps; finger tighten the bolts. Refer to figure for proper bolt placement. 11. Torque M10 camshaft cap bolts to 20 N m (15 lb ft) and then torque to N m (37-40 lb ft) using torque sequence shown in figure.

8 12. Torque the nine 63 mm M8 bolts to 30 N m (22 lb ft) using the torque sequence. 13. Remove crankshaft locking tool (W ) from CKP sensor hole in the flywheel housing. 14. Install CKP sensor. 15. Install a dial indicator onto gear case and zero out the dial indicator. 16. Position the stem of dial indicator to rest between the teeth on the camshaft gear. 17. Hold the number five idler gear with a screwdriver. Check the lash between the camshaft gear and idler gear number five.

9 18. The dial indicator should read mm ( in.). If the gear lash is excessive between either camshaft gear and the number five idler gear, inspect the number five idler gear spindle, camshaft gear and camshaft housing. Repair as necessary. NOTICE: The camshaft journal area (1) is lubricated by oil that has to travel through the rocker shaft. If the rocker shaft is installed incorrectly, oil passages do not line up. This results in insufficient lubrication and damage to the camshaft journals. Incorrect shaft installation may also result in the engine brakes not functioning and cause damage to the rocker arm bushings.

10 NOTICE: Ensure when tightening the rocker shaft bolts that the bolts are drawn down from the inside bolts outward in 1/2 turn increments, before final torque. If the rocker shaft bolt is fully torqued without using the increment procedure the rocker shaft can break. 19. Using intake rocker arm lifter and spacer tool (1) (W ), install the assembled intake rocker arm assembly to the camshaft cap and secure with seven clamping blocks and bolts. 20. Torque the bolts to N m (36-41 lb ft) +90 degrees. Follow torque sequence below.

11 21. Using tool (W ), install the assembled exhaust rocker arm assembly to the camshaft cap. 22. Torque the bolts to N m (36-41 lb ft) +90 degrees. Follow torque sequence below. 23. Remove timing tools. 24. Install the injectors and harness. Refer to section Lash the valves and engine brakes. Refer to section Install the rocker cover. Refer to section Reconnect the battery power to the engine. 28. Install air cleaner bracket with eight bolts. 29. Install air cleaner housing. 30. Install the turbocharger inlet pipe and hose, and air cleaner.

12 ENGINE BRAKE The engine uses a dual overhead camshaft and rocker shaft design. The intake and exhaust camshafts must be timed to each other and also timed to the crankshaft. The timing is accomplished through the geartrain. The engine uses an integral engine brake. Engine braking is controlled electronically by the engine control system with an electric solenoid. When activated, the solenoid allows oil pressure to activate a piston on the exhaust rocker arm. Engine braking is accomplished with a single exhaust valve in each cylinder. The exhaust camshaft uses a separate engine brake-only lobe that allows for double valve activation for high efficiency braking. The exhaust valve is firstoperatedtowardthecompletionof the intake stroke, closed during the compression stroke and opened a second time when the compression stroke is completed. The engine brake system is enabled using the following components: Engine brake solenoid valve low (Y132). Engine brake solenoid valve medium (Y133). Six exhaust rocker arms with actuator pistons (2). Six brake rocker arms (3) which are actuated by the brake cam lobes (10). Exhaust rocker arm shaft (6) with an oil passage for lubricating the rocker arm and two additional oil passages (oil passage for cylinders 1 and 2 (4) and oil passage for cylinders 3 to 6 (5)) for supplying pressurized oil to the exhaust rocker arm with actuator piston (2). Exhaust camshaft (7) with one brake cam lobe (10) per cylinder. 1. Exhaust Rocker Arm 7. Exhaust Camshaft 2. Exhaust Rocker Arm with Actuator Piston 8. Actuator Piston 3. Brake Rocker Arm 9. Outlet Valve 4. Oil Passage for Cylinders 1 and Brake Cam Lobe 5. Oil Passage for Cylinders 3 6 Y132 Engine Brake Solenoid Valve Low 6. Exhaust Rocker Arm Shaft Y133 Engine Brake Solenoid Valve Medium

13 REMOVAL OF THE ENGINE BRAKE Remove as follows: 1. Turn engine OFF, (key OFF, engine OFF). 2. Steam clean the engine. NOTE: Ensure the engine is at ambient temperature. 3. Disconnect the starting system. 4. Remove the air cleaner and the turbocharger inlet pipe and hose. 5. Disconnect the battery power to the engine. 6. Remove air cleaner housing. 7. Remove eight bolts from air cleaner bracket and remove bracket. 8. Remove nineteen bolts from rocker cover and remove rocker cover. 9. Disconnect the two harnesses from the cam frame housing to disconnect the engine brake solenoids (Y132 and Y133) and the injectors. 10. Remove the engine brake solenoid (Y132 and Y133) and injector connections. and then remove the intermediate cam frame. 11. Remove the engine brake solenoids (Y132 and Y133). NOTICE: Ensure when loosening the rocker shaft bolts that the bolts are loosened from the inside bolts outward in 1/2 turn increments. The rocker shaft can break without using the increment procedure.

14 NOTE: After the rocker shaft bolts are loosened completely, remove the brake rocker arm springs before removing the shaft assembly; there is a risk that the springs can fall into the gear case. 12. Completely loosen all of the adjusting screws on all of the exhaust rocker arms. 13. Loosen the seven bolts securing the exhaust rocker arm to the bridge. 14. Using exhaust rocker arm lifter and spacer tool (W ), remove the exhaust rocker assembly from the camshaft housing. INSPECTION OF THE ENGINE BRAKE Inspect as follows: 1. Inspect the exhaust rocker arm with actuator piston for damage or wear; replace if necessary. 2. Inspect the two engine brake solenoids for wear or damage; replace if necessary. 3. Inspect the brake rocker arm for wear or damage; replace if necessary.

15 INSTALLATION OF THE ENGINE BRAKE Install as follows: 1. Install the exhaust rocker arm with actuator piston and brake rocker arm onto exhaust rocker shaft. NOTICE: The camshaft journal area (1) is lubricated by oil that has to travel through the rocker shaft. If the rocker shaft is installed incorrectly, oil passages do not line up. This results in insufficient lubrication and damage to the camshaft journals. Incorrect shaft installation may also result in the engine brakes not functioning and cause damage to the rocker arm bushings. 2. Using intake rocker arm lifter and spacer tool (W ), install the assembly into the camshaft housing.

16 NOTICE: Ensure when tightening the rocker shaft bolts that the bolts are drawn down from the inside bolts outward in 1/2 turn increments, before final torque. If the rocker shaft bolt is fully torqued without using the increment procedure the rocker shaft (1) can break. NOTE: Assemble the brake rocker arm springs before tightening shaft bolts. 3. Install seven bolts into the rocker shaft and bracket. 4. Tighten the seven bolts N m (36-40 lb ft) plus 90 degree torque turn. NOTE: Ensure solenoid is completely seated in bore prior to torquing screw. NOTE: The hold-down screws are located in the injector harness.

17 5. Install the two brake solenoids (3) with new seal O-rings (4). Torque the solenoid hold-down screws to 10 N m (7 lb ft). NOTICE: Ensure when tightening the terminal connector (2) that the connector does not contact the solenoid housing. A short to all the injectors will occur if contact is made. 6. Install injector harness contacts to solenoids.

18 7. Place a 0.65 mm feeler gauge (or equivalent) as a spacer between the connector and the solenoid housing to keep sufficient clearance to avoid a short between the connector and solenoid housing. Torque the connector nut to 1.5 N m (13 lb in.). 8. Install rocker cover. NOTE: Anytime the engine brake lash is set the valve lash will need to be adjusted. NOTE: Set the valve lash before setting the engine brake lash. VALVE LASH ADJUSTMENT Adjust the valves as follows: 1. Turn engine OFF, (key OFF, engine OFF). 2. Steam clean the engine. 3. Disconnect battery power to the engine. 4. Remove the air cleaner and the turbocharger inlet pipe and hose. 5. Remove air cleaner housing. 6. Remove eight bolts from air cleaner bracket and remove bracket. 7. Remove nineteen bolts from rocker cover. 8. Remove rocker cover. 9. Bar the engine over until cylinder number one is at top dead center (TDC). 10. Lash intake valves one, two and four to 0.4 mm (0.016 in.).

19 11. Lash exhaust valves one, three and five to 0.6 mm (0.024 in.). 1. Feeler Gauge Location between the Rocker Arm and Valve 2. Feeler Gauge 12. Rotate the engine 360 from the flywheel housing, until cylinder number six is at TDC, for a setting of 180 from the camshafts. 13. Lash intake valves three, five, and six to 0.4 mm (0.016 in.). 14. Lash exhaust valves two, four and six to 0.6 mm (0.024 in.). 15. Torque the locknut valve adjusting screw to 50 N m (37 lb ft). 16. Remove any tools used for this procedure. 17. Install the rocker cover. 18. Reconnect the battery power to the engine. 19. Install air cleaner bracket with eight bolts. 20. Install air cleaner housing. 21. Install the turbocharger inlet pipe and hose, and air cleaner. SETTING THE ENGINE BRAKE LASH Set the lash as follows: 1. Set the lash on all the exhaust adjusting screws first (all the adjusting screws in direct contact with the exhaust valves). 2. Rotate the engine until a given cylinder is at maximum intake lift. When this is reached, the brake lash can be set on this cylinder. 3. When the brake rocker arm is in contact with the exhaust valve, set the lash between the brake rocker arm adjusting screw and the actuator piston stem. Set the lash to 4.1 mm ( in.).

20 4. Lash the engine brakes in the following firing order; 1, 5, 3, 6, 2, and Torque the locknut valve adjusting screw to 50 N m (37 lb ft).

21

22 ADDITIONAL SERVICE INFORMATION Additional service information is available in Power Service Literature. Detroit Diesel, DDC, Series 60 and the spinning arrows design are registered trademarks of Detroit Diesel Corporation. Copyright 2009 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07/10 DD Platform DATE: September 2010

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07/10 DD Platform DATE: September 2010 NUMBER: 9 09 10 S.M. REF.: Listed in Table ENGINE: EPA07/10 DD Platform DATE: September 2010 SUBJECT: INSTALLATION OF THE CAMSHAFT AND ROCKER SHAFT/ENGINE BRAKE ASSEMBLY ADDITIONS, REVISIONS, OR UPDATES

More information

Camshaft and Idler Gear August Removal of the Camshafts. Installation of the Camshafts. Removal of the Intake Rocker Shaft Assembly

Camshaft and Idler Gear August Removal of the Camshafts. Installation of the Camshafts. Removal of the Intake Rocker Shaft Assembly 08 11-16 1 08 11-16 SUBJECT DATE Camshaft and Idler Gear August 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshafts Added notice and

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: February 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: February 2009 NUMBER: 2 10-09 S.M. REF.: Listed in Table ENGINE: DD15 DATE: February 2009 SUBJECT: CAMSHAFT TIMING ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0002

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: February 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: February 2009 NUMBER: 2 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: February 2009 SUBJECT: VALVE LIFT SPECIFICATIONS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES NUMBER: 8 34 13 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0005

More information

NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009

NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009 NUMBER: 10 09 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009 SUBJECT: INTERMEDIATE FRAME / FUEL INJECTOR WIRING HARNESS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

Removal and Installation of the Camshaft Housing Assembly February Removal of the Camshaft Housing Assembly

Removal and Installation of the Camshaft Housing Assembly February Removal of the Camshaft Housing Assembly 1 SUBJECT DATE Removal and Installation of the Camshaft Housing Assembly February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshaft

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 SUBJECT DATE Camshaft Housing Assembly March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshaft Housing DDC-SVC-MAN-0081 DD Platform

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 10 18-16 SUBJECT DATE Symptom Diagnostics - Noise October 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change EPA07/10/ DDC-SVC-MAN-0084 GHG14 DD Platform Overhead

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 1 38-13 SUBJECT DATE Inspection of the Main and Connecting Rod Bearings In-Chassis January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Inspection of

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: April 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: April 2009 NUMBER: 4 8 09 S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: April 2009 SUBJECT: CYLINDER HEAD INSTALLATION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page

More information

Section 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) Model

Section 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) Model Page 1 of 22 Section 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) Model Series 60 EGR uses a camshaft gear assembly. Camshaft, camshaft drive gear and camshaft gear cover are the

More information

NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009

NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 NUMBER: 7 4 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 SUBJECT: EXHAUST GAS RECIRCULATION COOLER WATER MANIFOLD ASSEMBLY ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

Updated gear lash procedures for the compact gear train assembly have been added to the Series 60 Service Manual.

Updated gear lash procedures for the compact gear train assembly have been added to the Series 60 Service Manual. NUMBER: 14 60 03 S.M. REF.: 1.21 ENGINE: 60 DATE: November 2003 SUBJECT: GEAR TRAIN AND CAMSHAFT GEAR LASH PROCEDURES FOR THE COMPACT GEAR TRAIN ASSEMBLY INTRODUCTION Updated gear lash procedures for the

More information

Section 7.3 Water Manifold has been updated.

Section 7.3 Water Manifold has been updated. NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES NUMBER: 6 25 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change E3 Fuel

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE NUMBER: 10 01 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform

More information

Engine Valve Lash - Inspect/Adjust

Engine Valve Lash - Inspect/Adjust Page 1 of 5 Shutdown SIS Previous Screen Product: TRUCK ENGINE Model: 3126E TRUCK ENGINE CKM Configuration: 3126E Truck Engine CKM00001-UP Testing and Adjusting 3126B and 3126E Truck Engine Media Number

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 5 33-13 SUBJECT Removal and Installation of the High Pressure Fuel Pump -Three- Filter System DATE May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2010

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2010 NUMBER:10 02 10 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2010 SUBJECT: DOUBLEHYSTERESISTEST ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page

More information

Section 1.24 Gear Train and Engine Timing

Section 1.24 Gear Train and Engine Timing Page 1 of 20 Section 1.24 Gear Train and Engine Timing The gear train is completely enclosed between the gear case and gear case cover and is located at the front of the engine. The gear train consists

More information

Engine Valve Lash - Inspect/Adjust

Engine Valve Lash - Inspect/Adjust https://siswecat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... Page 1 of 5 Shutdown SIS Previous Screen Product: TRUCK ENGINE Model: C15 TRUCK ENGINE BXS Configuration: C15 On-highway

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010 NUMBER: 815 10 S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010 SUBJECT: SPN 3226 FMI 13 SCR OUTLET NOX SENSOR SIGNAL NOT AVAILABLE ADDITIONS, REVISIONS, OR UPDATES Publication Number

More information

Engine Valve Lash - Inspect/Adjust

Engine Valve Lash - Inspect/Adjust Page 1 of 5 7HVWLQJDQG$GMXVWLQJ &&DQG&2QKLJKZD\(QJLQHV 0HGLD1XPEHU5(15 3XEOLFDWLRQ'DWH 'DWH8SGDWHG Engine Valve Lash - Inspect/Adjust SMCS - 1102-025 L To prevent possible injury, do not use the starter

More information

https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html

https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html Page 1 of 7 NOTE: The timing pin is used to accurately locate TDC for setting the overhead. The timing pin is typically located below the fuel pump. for front gear train engines, in the front gear housing

More information

Installation of the DD13,DD15, and DD16 Cylinder Head February Installation of the DD13 Cylinder Head

Installation of the DD13,DD15, and DD16 Cylinder Head February Installation of the DD13 Cylinder Head 5 02-12Rev 1 5 02-12Rev SUBJECT DATE Installation of the DD13,DD15, and DD16 Cylinder Head February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation

More information

Engine Replacement Procedures September Removal of the Complete Powertrain Assembly. Replacement Long Block Engine Preparation

Engine Replacement Procedures September Removal of the Complete Powertrain Assembly. Replacement Long Block Engine Preparation 9 05-15 1 9 05-15 SUBJECT DATE Engine Replacement Procedures September 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Complete Powertrain

More information

The EPA07 Series 60 Workshop Manual has been revised. Listed in Table 1 are the revisions.

The EPA07 Series 60 Workshop Manual has been revised. Listed in Table 1 are the revisions. NUMBER: 08 60-6 S.M. REF.: 2.3.1 and 2.3.2 ENGINE: EPA07 Series 60 DATE: September 2008 SUBJECT: E3 INJECTOR TUBE PUBLICATION: DDC-SVC-MAN-0005 The EPA07 Series 60 Workshop Manual has been revised. Listed

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: February 2011

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: February 2011 NUMBER: 2 15 11 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: February 2011 SUBJECT: FAULTY FUEL INJECTOR ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page

More information

SPN 1176/FMI 3 SPN 1176/FMI 4

SPN 1176/FMI 3 SPN 1176/FMI 4 NUMBER: 8 01 13 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 900 DATE: August 2013 SUBJECT: SPN 1176/FMI 3, 4 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0015

More information

Section 13.2 Valve Lash, Injector Height (Timing) and Jake Brake Lash Adjustments

Section 13.2 Valve Lash, Injector Height (Timing) and Jake Brake Lash Adjustments Page 1 of 15 Section 13.2 Valve Lash, Injector Height (Timing) and Jake Brake Lash Adjustments Accurate adjustment of clearance between valve buttons, intake and exhaust valves is important if maximum

More information

Valve Lash and Valve Bridge Adjustment

Valve Lash and Valve Bridge Adjustment Valve Lash and Valve Bridge Adjustment Illustration 1 g00286271 (1) 147-2060 Wrench (2) 147-2059 Torque Wrench (3) 148-7211 Bridge Nut Socket (4) 145-5191 Gauge Support (5) 147-2056 Dial Indicator (6)

More information

Static Injection Timing

Static Injection Timing Page 1 of 13 006-025 Static Injection Timing General Information The static timing is relative to the amount of push tube travel remaining when the piston is 5.161 mm [0.2032 in], or 19 degrees before

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009 NUMBER: 4 7 09 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009 SUBJECT: SPN 27 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0009

More information

NUMBER: S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008

NUMBER: S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008 NUMBER: 08 60-7 S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008 SUBJECT: EGR RATE MEASUREMENT SYSTEM PUBLICATION: DDC-SVC-MAN-0005 EGR Rate Measurement System has new information added. EGR

More information

Service Bulletin Trucks

Service Bulletin Trucks Mack Trucks, Inc. Greensboro, NC USA Service Bulletin Trucks Date Group No. Release Page This service bulletin replaces bulletin 214-93 dated 5.2010. 7.2013 214 93 02 1(13) Valves and Engine Injectors,

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009 NUMBER: 3 3 09 S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009 SUBJECT: FUEL FILTER ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0037

More information

Rocker Lever Assembly

Rocker Lever Assembly 003-009 Rocker Lever Assembly Preparatory Steps Remove the air piping from the intake manifold. Remove the rocker lever cover. Refer to Procedure 003-011 in Section 3. Remove the engine brakes, if equipped.

More information

SPN 723/FMI 3, 8, 10, 11, 31 - All Years February SPN 723/FMI 3 - All Years. SPN 723/FMI 8 - All Years. SPN 723/FMI 10 - All Years

SPN 723/FMI 3, 8, 10, 11, 31 - All Years February SPN 723/FMI 3 - All Years. SPN 723/FMI 8 - All Years. SPN 723/FMI 10 - All Years 1 49-13 1 1 49-13 SUBJECT DATE SPN 723/FMI 3, 8, 10, 11, 31 - All Years February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 723/FMI 3 - All Years

More information

Page 1 of 12 Section 2.3 N2 Electronic Unit Injector The N2 Electronic Unit Injector (EUI) is a lightweight, compact unit that injects diesel fuel directly into the combustion chamber. See Figure "N2 Electronic

More information

NUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029

NUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029 NUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029 The procedure and direction for SPN 1636 have changed. SPN

More information

Cylinder Liner January Removal of the Cylinder Liner. Cleaning of the Cylinder Liner. Inspection of the Cylinder Liner

Cylinder Liner January Removal of the Cylinder Liner. Cleaning of the Cylinder Liner. Inspection of the Cylinder Liner 01 18-16 1 01 18-16 SUBJECT DATE Cylinder Liner January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Cylinder Liner Added information to

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 8 04-12 SUBJECT DATE SPNs 4354/FMI 5, 4355/FMI 5, 4356/FMI 5, 4357/FMI 5 August 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4354/FMI 5 DDC-SVC-MAN-0084

More information

NUMBER: S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007

NUMBER: S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007 NUMBER: 1 60 07 S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007 SUBJECT: N3 ELECTRONIC INJECTOR PUBLICATION: 6SE483 The Series 60 Service Manual has been revised. Engine models built from December

More information

Removal and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head

Removal and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head 4 102-12 1 4 102-12 SUBJECT DATE Removal and Installation of the DD15 and DD16 Cylinder Head April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081

More information

Piston and Connecting Rod Assembly January Removal of the Piston and Connecting Rod Assembly

Piston and Connecting Rod Assembly January Removal of the Piston and Connecting Rod Assembly 1 18-13 1 1 18-13 SUBJECT DATE Piston and Connecting Rod Assembly January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Piston and Connecting

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 8 05-12 SUBJECT DATE SPN 4354/FMI 5, 4356/FMI 5, 4355/FMI 5, 4357/FMI 5 August 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4354/FMI 5 DDC-SVC-MAN-0084

More information

Piston and Connecting Rod Assembly August Removal of the Piston and Connecting Rod Assembly

Piston and Connecting Rod Assembly August Removal of the Piston and Connecting Rod Assembly 1 8 17-13 SUBJECT DATE Piston and Connecting Rod Assembly August 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Piston DDC-SVC-MAN-0081 DD

More information

Removal of the High Pressure Fuel Pump April Publication Number / Title Platform Section Title Change. Removal of the High Pressure Fuel Pump

Removal of the High Pressure Fuel Pump April Publication Number / Title Platform Section Title Change. Removal of the High Pressure Fuel Pump 4 99-12 1 4 99-12 SUBJECT DATE Removal of the High Pressure Fuel Pump April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the High Pressure Fuel

More information

NOTE: These gears are measured and adjusted with the gear case cover installed.

NOTE: These gears are measured and adjusted with the gear case cover installed. SERIES 60 SERVICE MANUAL 4. The procedure for measuring the lash between the bull gear and the fuel pump drive gear (if applicable) and the air compressor and power steering pump drive gear is similar

More information

Adjusting valve clearance

Adjusting valve clearance Adjusting valve clearance Engines314, 352, 352 A 355, 355 A 360, 360 A 362 LA 364, 366, 366 A/ LA Adjustment values in mm Engine Intake valve Exhaust valve Tolerance range 1) 314, 352, 352 A.V 2) 0.20

More information

EGR Actuator Slow Learn April Installation of the DD13 Exhaust Gas Recirculation Valve Actuator Pull Rod

EGR Actuator Slow Learn April Installation of the DD13 Exhaust Gas Recirculation Valve Actuator Pull Rod 1 4 07-13 SUBJECT DATE EGR Actuator Slow Learn April 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0083 Installation of the DD13 Exhaust Gas

More information

NUMBER: 08 MBE REV S.M. REF.: 1.4 ENGINE: EPA07 MBE 4000 DATE: February 2008 SUBJECT: CYLINDER BLOCK LINER SERVICE PROCEDURE

NUMBER: 08 MBE REV S.M. REF.: 1.4 ENGINE: EPA07 MBE 4000 DATE: February 2008 SUBJECT: CYLINDER BLOCK LINER SERVICE PROCEDURE NUMBER: 08 MBE 4000-1 REV S.M. REF.: 1.4 ENGINE: EPA07 MBE 4000 DATE: February 2008 SUBJECT: CYLINDER BLOCK LINER SERVICE PROCEDURE PUBLICATION: DDC-SVC-MAN-0026 (6SE420) Amended tool number J-46180. New

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 2 07-13 SUBJECT DATE Removal and Installation of the Camshaft Housing February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 EPA07/10/

More information

EPA10 DOC Inlet Pressure Sensor November Removal of the EPA10 Diesel Oxidation Catalyst Inlet Pressure Sensor. without Sensor Box

EPA10 DOC Inlet Pressure Sensor November Removal of the EPA10 Diesel Oxidation Catalyst Inlet Pressure Sensor. without Sensor Box 11 10-14 1 11 10-14 SUBJECT DATE EPA10 DOC November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the EPA10 DDC-SVC-MAN-0083 EPA10 DD Platform

More information

Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)

Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D) SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Rocker Arm Assembly» Service and Repair» Procedures» Cam, Valve Springs & Seals, Cam Roller Follower and Lifter Camshaft, Valve Springs,

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

1.2.5 Installation of Cylinder Head

1.2.5 Installation of Cylinder Head SERIES 50 SERVICE MANUAL 1.2.5 Installation of Cylinder Head Perform the following steps for cylinder head installation: 1. Be sure piston domes and the cylinder head and cylinder block firedeck surfaces

More information

Engine Brake, Design and Function. This information covers the design and function of the Volvo Engine Brake (VEB) on the Volvo D11F engine.

Engine Brake, Design and Function. This information covers the design and function of the Volvo Engine Brake (VEB) on the Volvo D11F engine. Volvo Trucks North America Greensboro, NC USA Service Bulletin Trucks ate Group No. Page 11.2006 253 53 1(7) Engine Brake esign and Function 11F Engine Brake, esign and Function W2005865 This information

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: April 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: April 2009 NUMBER: 4 11 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: April 2009 SUBJECT: SPN 2631 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0010

More information

EGR heater plate removal and installation procedure has been added.

EGR heater plate removal and installation procedure has been added. NUMBER: 08 60-3 S.M. REF.: 8.3 ENGINE: EPA07 Series 60 DATE:June 2008 SUBJECT: EGR HEATER PLATE PUBLICATION: DDC-SVC-MAN-0005 EGR heater plate removal and installation procedure has been added. 8.3.1 REMOVAL

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking

More information

High pressure fuel line and transfer tube removal and installation procedures have been updated.

High pressure fuel line and transfer tube removal and installation procedures have been updated. NUMBER: 08 MBE 4000-3 S.M. REF.: 2.3 ENGINE: EPA04 MBE 4000 DATE: July 2008 SUBJECT: HIGH PRESSURE FUEL LINE AND TRANSFER TUBE PUBLICATION:DDC-SVC-MAN-0023 High pressure fuel line and transfer tube removal

More information

Overhead Set ( )

Overhead Set ( ) ISB, ISBe, ISBe4, QSB4.5, QSB5.9, and QSB6.7 (Common Rail Fuel System) Series Engines Service Manual Overhead Set (003-004) General Information Overhead setting is only required at the interval specified

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: May 2013 SUBJECT: SPN 2631/FMI 2 ADDITIONS, REVISIONS, OR UPDATES

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: May 2013 SUBJECT: SPN 2631/FMI 2 ADDITIONS, REVISIONS, OR UPDATES NUMBER: 5 26 13 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: May 2013 SUBJECT: SPN 2631/FMI 2 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0010

More information

Valve Clearance Adjustment

Valve Clearance Adjustment 2006 Odyssey Valve Clearance Adjustment Report a problem with this article NOTE: Adjust the valves only when the cylinder head temperature is less than 100 ºF (38 ºC). 1. Remove the intake manifold. 2.

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................

More information

Removal and Installation of the Fuel Injector Cup February Removal of the Fuel Injector Cup Three-Filter System and Two-Filter System

Removal and Installation of the Fuel Injector Cup February Removal of the Fuel Injector Cup Three-Filter System and Two-Filter System 1 2 25-14 SUBJECT DATE Removal and Installation of the Fuel Injector Cup February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Fuel Injector

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

Hydrocarbon Fuel Doser Injector Valve Fuel Supply Line December Publication Number / Title Platform Section Title Change

Hydrocarbon Fuel Doser Injector Valve Fuel Supply Line December Publication Number / Title Platform Section Title Change 1 SUBJECT DATE Hydrocarbon Fuel Doser Injector Valve Fuel Supply Line December 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Hydrocarbon

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 02 06-16 SUBJECT DATE Fuel Rail - Three-Filter System February 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 DD Platform - All Years

More information

Classification: Reference: Date: VE30DE CAM TIMING

Classification: Reference: Date: VE30DE CAM TIMING Classification: Reference: Date: EM93-002 NTB93-126 September 2, 1993 VE30DE CAM TIMING APPLIED VEHICLE(S): All equipped with VE30DE Engine SERVICE INFORMATION When servicing VE30DE engine cylinder heads,

More information

Valve Rocker Arm and Push Rod Installation (6.2L LS3)

Valve Rocker Arm and Push Rod Installation (6.2L LS3) 9. Tighten the cylinder head bolts: 10.1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N m (22 lb ft). 10.2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence

More information

NUMBER: 08 FSTG 12 REV S.M. REF.: Listed in Table ENGINE: EPA07 DD15 DATE: February 2009

NUMBER: 08 FSTG 12 REV S.M. REF.: Listed in Table ENGINE: EPA07 DD15 DATE: February 2009 NUMBER: 08 FSTG 12 REV S.M. REF.: Listed in Table ENGINE: EPA07 DD15 DATE: February 2009 SUBJECT: ISB (IDLE SPEED BALANCE) VALUES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title

More information

Publication Number / Title Platform Section Title Change. Removal of the High Pressure Fuel Pump Drive Gear - Three-Filter System

Publication Number / Title Platform Section Title Change. Removal of the High Pressure Fuel Pump Drive Gear - Three-Filter System 5 34-13 1 5 34-13 SUBJECT Removal and Installation of the High Pressure Fuel Pump Drive Gear - Three-Filter System DATE June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: September 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: September 2009 NUMBER: 9 3 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: September 2009 SUBJECT: TURBOCHARGER WASTEGATE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page

More information

Bthird, or power stroke by the expanding gases. As the

Bthird, or power stroke by the expanding gases. As the third, or power stroke by the expanding gases. As the piston reaches DC it enters the fourth cycle. The exhaust valve opens and the piston rises forcing burned gases from the combustion chamber in what

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 12 02-12 SUBJECT DATE Test E - Three-Filter Fuel System December 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform Test E - Three-Filter

More information

TUNE-UP KIT INSTRUCTIONS

TUNE-UP KIT INSTRUCTIONS Jacobs Engine Brake Tune-Up Kit 790/795 Series P/N 29013 Information in this manual was current at time of printing and is subject to change without notice or liability. TUNE-UP KIT INSTRUCTIONS Refer

More information

Removal of the Needle, Amplifier, and Pressure Limiting Valve Return Lines Three-Filter System

Removal of the Needle, Amplifier, and Pressure Limiting Valve Return Lines Three-Filter System 1 5 02-13 SUBJECT Needle, Amplifier, and Pressure Limiting Valve Return Lines Three- Filter System, Fuel Rail - Three-Filter System DATE February 2013 Additions, Revisions, or Updates Publication Number

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

Fuel Filter Maintenance Intervals July EPA10/GHG14 DD Series Preventive Maintenance Tables

Fuel Filter Maintenance Intervals July EPA10/GHG14 DD Series Preventive Maintenance Tables 1 7 14-13 SUBJECT DATE Fuel Filter Maintenance Intervals July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0080 EPA10/ GHG14 DD Platform EPA10/GHG14

More information

Precision Degree Wheel Kit

Precision Degree Wheel Kit 555-81621 Precision Degree Wheel Kit Instruction Booklet Instructions for 81621 Camshaft Degree Kit Thank you for purchasing the Jegs Camshaft Degree Kit. Please follow these detailed instructions to properly

More information

DODGE CUMMINS ARP HEAD STUDS. Installation Instructions

DODGE CUMMINS ARP HEAD STUDS. Installation Instructions Installation Manual ARP Head Studs P/N 247-4202 425 s P/N 247-4204 625 s 2003-2014 DODGE CUMMINS ARP HEAD STUDS Installation Instructions Dodge Cummins 5.9L & 6.7L 24V ARP 425 s 247-4202 Dodge Cummins

More information

Overhead Set. Measure WARNING. General Information

Overhead Set. Measure WARNING. General Information Page 1 of 16 003-004 Overhead Set Measure General Information All overhead lash measurements must be made when the engine is cold. Stabilized coolant temperature must be at 60 C [140 F] or below. Remove

More information

2.2L 4-CYL - VIN [S]

2.2L 4-CYL - VIN [S] 2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article

More information

Page 1 of 9 303-01C Engine 6.0L Diesel 2004 F-Super Duty 250-550/Excursion DESCRIPTION AND OPERATION Procedure revision date: 08/06/2003 Engine Printable View Engine Description The 6.0L diesel engine

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 8 22-13 SUBJECT DATE Water Manifold Assembly August 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation of the DD13 EGR Cooler Water DDC-SVC-MAN-0081

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 6 07-15 SUBJECT DATE SPN 3464 (MCM) (EPA10;GHG14) June 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3464/FMI 3 - DDC-SVC-MAN-0084 EPA10/ GHG14 DD

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)

More information

2.4L 4-CYL - VINS [F,H,S]

2.4L 4-CYL - VINS [F,H,S] 2.4L 4-CYL - VINS [F,H,S] 1990 Nissan 240SX 1990 ENGINES Nissan 2.4L 4-Cylinder Axxess, Pickup, Stanza, 240SX * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,

More information

20.Cylinder Block. Cylinder Block A: REMOVAL ME(H4DOTC)-63 ST CRANKSHAFT STOPPER

20.Cylinder Block. Cylinder Block A: REMOVAL ME(H4DOTC)-63 ST CRANKSHAFT STOPPER Cylinder Block MECHANICAL 20.Cylinder Block A: REMOVAL Before conducting this procedure, drain engine oil completely. 1) Remove the intake manifold. 2)

More information

NOTE: Read the entire procedure for overhead adjustment before attempting to perform this operation.

NOTE: Read the entire procedure for overhead adjustment before attempting to perform this operation. 1 of 16 1/11/2017 1:56 PM Batteries can emit explosive gases. To reduce the possibility of personal injury, always ventilate the compartment before servicing the batteries. To reduce the possibility of

More information