Cab Kit Installation Instructions

Transcription

1 Low Speed Vehicles (LSV) Electric Vehicles: Carryall Carryall 6 Cab Kit Installation Instructions Publication These instructions apply to the following kit: 0670 Edition Code 008E09D

2 GENERAL INFORMATION AND PRECAUTIONS This instruction provides detailed instructions for the installation of the cab kit. These instructions pertain to LSV Carryall and Carryall 6 electric vehicles. Order the following accessories separately Door Kit, CCI P/N Rear Window Kit, CCI P/N Heater/Defroster Kit, CCI P/N NOTE: Nylon washers have been supplied to provide a weather seal around all exterior hardware. A nylon washer must be installed under each bolt head, directly against the cab exterior. Overtightening hardware could damage the nylon washers. Thoroughly review this document before performing any installation procedures. The following safety statements relate to specific safety issues and must be read, understood, and heeded before a kit is installed. Failure to do so could result in personal injury and/or property damage. ý DANGER Battery Explosive gases! Do not smoke. Keep sparks and flames away from the vehicle and service area. Ventilate when charging or operating vehicle in an enclosed space. Wear a full face shield and rubber gloves when working on or near batteries. Battery Poison! Contains acid! Causes severe burns. Avoid contact with skin, eyes, or clothing. Antidotes: - External: Flush with water. Call a physician immediately. - Internal: Drink large quantities of milk or water. Follow with milk of magnesia or vegetable oil. Call a physician immediately. - Eyes: Flush with water for 5 minutes. Call a physician immediately. Gasoline Flammable! Explosive! Do not smoke. Keep sparks and flames away from the vehicle and service area. Service only in a well-ventilated area. Do not operate gasoline vehicle in an enclosed area without proper ventilation. The engine produces carbon monoxide, which is an odorless, deadly poison. A Club Car vehicle will not provide protection from lightning, flying objects, or other stormrelated hazards. If caught in a storm while driving a Club Car vehicle, exit the vehicle and seek shelter in accordance with applicable safety guidelines for your location. ý WARNING Follow the procedures exactly as stated in this instruction, and heed all DANGER, WARNING, and CAUTION statements in this instruction as well as those on the vehicle and battery charger. WARNING CONTINUED ON NEXT PAGE... Copyright 009 Club Car, Inc. Page Cab Kit Installation Instructions (050770)

3 ý WARNING Club Car electric vehicles are designed without a chassis ground. Failure to maintain this chassis isolation could result in a potential fire hazard. Only trained technicians should service or repair the vehicle or battery charger. Anyone doing even simple repairs or service should have knowledge and experience in electrical and mechanical repair. The appropriate instructions must be used when performing maintenance, service, or accessory installation. Prior to servicing the vehicle or leaving the vehicle unattended, turn the key switch OFF, remove the key, set the park brake, and place the Forward/Reverse handle in the NEUTRAL position. Chock the wheels when servicing the vehicle. Ensure battery connections are clean and properly tightened. To avoid unintentionally starting the vehicle, disconnect the batteries as shown (Figures through, starting on page 6). Place Tow/Run switch in the TOW position before disconnecting or connecting the batteries. Failure to heed this warning could result in a battery explosion or severe personal injury. After disconnecting the batteries, wait 90 seconds for the controller capacitors to discharge. Use only -gauge (AWG) wires with low-resistance terminals to replace battery wires. Wear safety glasses or approved eye protection when servicing the vehicle or battery charger. Wear a full face shield and rubber gloves when working on or near batteries. Do not wear loose clothing or jewelry such as rings, watches, chains, etc., when servicing the vehicle or battery charger. Moving parts! Do not attempt to service the vehicle while it is running. Hot! Do not attempt to service hot engine, exhaust system, or motor. Failure to heed this warning could result in severe burns. Use insulated tools when working near batteries or electrical connections. Use extreme caution to avoid shorting of components or wiring. Lift only one end of the vehicle at a time. Use a suitable lifting device (chain hoist or hydraulic floor jack) with 000 lb. (5 kg) minimum lifting capacity. Do not use lifting device to hold vehicle in raised position. Use approved jack stands of proper weight capacity to support the vehicle and chock the wheels that remain on the floor. When not performing a test or service procedure that requires movement of the wheels, lock the brakes. If wires are removed or replaced, make sure wiring and wire harness are properly routed and secured. Failure to properly route and secure wiring could result in vehicle malfunction, property damage, personal injury, or death. For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle. If the vehicle is equipped with a prop rod, ensure that it is securely engaged while bed is raised. Do not close bed until all persons are clear of cargo bed area. Keep hands clear of all crush areas. Do not drop cargo bed; lower gently and keep entire body clear. Failure to heed this warning could result in severe personal injury or death. Cab Kit Installation Instructions (050770) Page

4 TOOLS REQUIRED 7/6-INCH SOCKET /-INCH /6-INCH SOCKET ALLEN-HEAD DRIVER ELECTRIC DRILL 7/6-INCH OPEN END WRENCH /-INCH OPEN END WRENCH RATCHET 5-50 FT-LB TORQUE WRENCH PHILLIPS HEAD SCREWDRIVER PLIERS 7/6-INCH DRILL BIT MIRROR MOUNTING GLUE PARTS IN THIS KIT NOTE: Replacement parts for cab may be obtained from Curtis Tractor Cab, Inc. Higgins St., Worcester, MA Telephone (508) or fax (800) ROOF SUPPORT BRACKET () EXTERIOR MIRROR FRONT COWL FRONT MOUNTING BRACKET (DRIVER SIDE) FRONT MOUNTING BRACKET (PASSENGER SIDE) REAR PANEL ROOF WINDSHIELD REAR CROSS BRACE REAR MOUNTING BRACKET (PASSENGER SIDE) REAR MOUNTING BRACKET (DRIVER SIDE) FILLER (PASSENGER SIDE) FILLER (DRIVER SIDE) FRONT COWL GASKET SPACERS SIDE FRAME (PASSENGER SIDE) SIDE FRAME (DRIVER SIDE) WINDSHIELD SUPPORT WEATHER STRIPPING CENTER HIGH-MOUNT STOP LIGHT MIRROR Page Cab Kit Installation Instructions (050770)

5 PARTS IN THIS KIT /-0 x -/ HEX-HEAD BOLT /-0 x -/ HEX-HEAD BOLT 5/6-8 x -/ PHILLIPS-HEAD MACHINE SCREW WIPER MOTOR WIPER MOUNTING HARDWARE /-0 x HEX-HEAD BOLT 5/6-8 x / 5/6-8 x ALLEN-HEAD BOLT ALLEN-HEAD BOLT /-0 NYLON LOCKNUT 5/6 WASHER 5/6-8 NYLON LOCKNUT 5/6-8 x / CARRIAGE BOLT WIPER ARM WIPER BLADE WIPER SHAFT HARDWARE / FLAT WASHER 7/6 NYLON WASHER RUBBER WASHER 5/6 ID X OD FENDER WASHER NYLON BUSHINGS FOR WIPER MOTOR AIR VENT MOUNTING BRACKET SEAT BELT RECEIVER LATCH SEAT BELT KIT SEAT BELT 7/6- x HEX-HEAD BOLT 7/6 FLAT WASHER LARGE FLAT WASHER 7/6- LOCKNUT Cab Kit Installation Instructions (050770) Page 5

6 . DISCONNECT THE BATTERY CABLES.. Disconnect the battery cables as instructed. See "To avoid unintentionally starting..." WARNING on page.. (+) (+) BATTERY EXPLOSION COULD RESULT IN SEVERE PERSONAL INJURY. BATTERY EXPLOSION COULD RESULT IN SEVERE PERSONAL INJURY. ( ) ( ) 8 7 Figure Battery Cable Removal Electric Vehicle Battery Configuration Carryall LSV (Viewed from driver side of vehicle). Place TOW/RUN Switch in TOW before disconnecting or connecting battery cables.. Remove negative battery cable.. Remove positive battery cable. Connect battery cables in reverse order. Figure Battery Cable Removal Electric Vehicle Battery Configuration Carryall 6 LSV (Viewed from driver side of vehicle). Place TOW/RUN Switch in TOW before disconnecting or connecting battery cables.. Remove negative battery cable.. Remove positive battery cable. Connect battery cables in reverse order. Page 6 Cab Kit Installation Instructions (050770)

7 . SECURE FRONT MOUNTING BRACKETS.. If vehicle has cup holders mounted to the dash, remove them and mount them to the other two holes in the dash... Secure the front mounting brackets ( and ) under the dash with two /-0 x hex-head bolts (), two washers (), and two lock nuts (5) each as shown (Figures and ). Do not tighten hardware at this time. 5 5 Figure Install Passenger-Side Front Mounting Bracket Figure Install Driver-Side Front Mounting Bracket. SECURE REAR MOUNTING BRACKETS TO SIDE FRAMES.. Secure the seat belt () to the passenger-side rear mounting bracket (7) with one 7/6- x hex-head bolt () and lock nut () as shown (Figure 5). Tighten hardware to 50 ft-lb (67.8 N m)... Secure passenger-side rear mounting bracket (7) to passenger-side frame with one 5/6-8 x / carriage bolt (9), flat washer (0), and lock nut () (Figure 5). Tighten hardware to 7 ft-lb (.0 N m)... Repeats steps. and. on the driver-side mounting bracket (8) Figure 5 Secure Rear Mounting Bracket (Passenger-side shown) Cab Kit Installation Instructions (050770) Page 7

8 . POSITION SIDE FRAMES TO VEHICLE NOTE: This step mounts the front of the side frames to the front mounting brackets only. The rear of the side frames will be secured to the rear panel and vehicle in later steps... Remove the seats from the vehicle... Access the engine compartment. See following DANGER. ý WARNING For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle. If the vehicle is equipped with a prop rod, ensure that it is securely engaged while bed is raised. Do not close bed until all persons are clear of cargo bed area. Keep hands clear of all crush areas. Do not drop cargo bed; lower gently and keep entire body clear. Failure to heed this warning could result in severe personal injury or death... Lift the bed and ensure the prop rod is engaged... With the aide of an assistant, hold the driver-side frame () in place as shown (Figure 6)..5. Loosely secure the tab on the driver-side frame to the front mounting bracket () with one 5/6-8 x / carriage bolt (6), washer (7), and lock nut (8). Do not tighten hardware at this time (Figure 6)..6. Repeat step.5 on the passenger-side frame Figure 6 Position and Secure Side Frames Page 8 Cab Kit Installation Instructions (050770)

9 5. SECURE REAR PANEL 5.. Align the mounting tabs on the side frames () to the holes in rear panel and loosely secure with two 5/6-8 x / carriage bolts () (through the top flange of the panel and into the tab on the side frame) one flat washer (), and lock nuts (5). Do not tighten the hardware at this time. 5.. Install a 5/6-8 x carriage bolt (), with nylon washer (5), through the upper hole in the rear panel, and side frame. Loosely secure with a flat washer (6) and lock nut (7). 5.. Secure bottom of rear panel () to rear mounting brackets (): 5... Install one 5/6-8 x carriage bolt (6), with nylon washer (7), through the upper hole in the rear panel, rear mounting bracket, and side frame. Loosely secure with a flat washer (8) and lock nut (9) Install a 5/6-8 x / carriage bolt (0), with nylon washer (), through the lower hole in the rear panel, rear mounting bracket and side frame. Loosely secure with a lock nut () Repeat steps 5. and 5.. on passenger-side frame. NOTE: Rear mounting brackets () will be secured to the vehicle in a later step (Figure 7) Figure 7 Secure Rear Panel to Side Frames Cab Kit Installation Instructions (050770) Page 9

10 6. SECURE REAR CROSS BRACE 6.. Align the holes in the rear cross brace () with the holes in the mounting tabs on the side frames and install 5/6-8 x / carriage bolts (), flat washers () and lock nuts () through rear-facing holes as shown (Figure 8). Tighten hardware to 7 ft-lb (.0 N m). Figure 8 Secure Top Rear Cross Brace 7. SECURE WINDSHIELD COWL Figure 9 Assemble Windshield Cowl 7.. Secure the front fillers ( and ) to the windshield cowl () with 5/6-8 x / carriage bolts (), nylon washers (5), flat washers (6), and lock nuts (7) as shown (Figure 9). 7.. Install windshield cowl gasket (8) onto inside edge of the windshield cowl assembly. Trim off any excess gasket. Page 0 Cab Kit Installation Instructions (050770)

11 7.. Align the windshield cowl assembly () with the mounting tabs on the driver-side frame () and secure with 5/6-8 x / carriage bolts (9), nylon washers (), flat washers () and lock nuts () (Figure 0). 7.. Install the 5/6-8 x / carriage bolts (5), flat washers (6) and lock nuts (7) through the tabs on the filler and into the mounting tabs on the side frame as shown (Figure 0) Align the ends of the windshield cowl with beginnings of the radius on the outside corners of the side frame tubes. Tighten hardware to 7 ft-lb (.0 N m) Repeat steps 7. through 7.5 on the passenger-side frame Figure 0 Secure Windshield Cowl Assembly to Side Frames Cab Kit Installation Instructions (050770) Page

12 8. SECURE WINDSHIELD SUPPORT, WINDSHIELD, AND ROOF SUPPORTS 8.. With the aid from an assistant, rest the bottom of the windshield (8) to the top of the cowl assembly (9) and loosely secure with two 5/6-8 x / carriage bolts (0), flat washers (), and lock nuts () (Figure, Detail A). 8.. Align the holes in the driver and passenger-side roof support brackets (5), the top windshield support (), and windshield frame (8) with the mounting tabs on the side frames (). Secure with 5/6-8 x / carriage bolts (), nylon washers (), flat washers (6), and lock nuts (7) as shown (Figure, Detail B). 8.. Secure the center roof support bracket () to the top windshield support () with one 5/6-8 x / carriage bolt (), nylon washer (), flat washer (6) and lock nut (7). See following NOTE. NOTE: Make sure the bulb weather stripping along the sides of the windshield is positioned correctly against the door side frames. Hardware will be installed in the top holes of the windshield support during the roof installation. The nylon washers () are installed under the carriage bolt heads directly against the cab exterior to provide a weather seal (Figure ). Overtightening hardware could damage the nylon washers. 8.. Position the rear-view mirror (9) to the lower corner of the windshield, and secure with one 5/6-8 x / hex head bolt (0), flat washer () and lock nut () as shown (Figure, Detail C) Secure the opposite arm (9) of the rear-view mirror to the existing phillips-head screw (0) and flat washer () on the front body Tighten all hardware to 7 ft-lb (.0 N m). 5 B Club Car c 0 A 8 9 C 9 Figure Secure Windshield, Top Support, and Roof Support Brackets Page Cab Kit Installation Instructions (050770)

13 9. INSTALL ROOF 9.. To install the /-inch weather-strip (), remove the backing tape and apply the weather strip to the top surface of the windshield support (), rear cross brace (), and side frames (6) as shown (Figure ). 9.. With the aid of an assistant, position the roof (5) on top of the weather-strip and side frames (6). 9.. Loosely secure the four corners of the roof (5) to the rear cross brace (), side frames (6), and windshield support () with four 5/6-8 x allen-head bolts (7), nylon washers (8), flat washers (9), and lock nuts (0). 9.. At the rear of the roof and centered, loosely install one 5/6-8 x -inch allen-head bolt, to be used for the center high mounted stop light in step Install the 5/6-8 x / allen-head bolts (), nylon washers (8), flat washers (), and lock nuts () in remaining roof holes. Tighten all hardware to 5 ft-lb (6.78 N m) Club Car Figure Secure Roof Cab Kit Installation Instructions (050770) Page

14 0. SECURE SIDE FRAMES TO VEHICLE 0.. Use the two slots at the bottom of each side frame (5) as a template and drill four 5/6-inch (8 mm) holes in vehicle floor (two per side). See following CAUTION. CAUTION Before drilling, check the underside of the floorboard and inside the body to make sure no vehicle components will be damaged by this drilling operation Figure Secure Side Frames to Vehicle 0.. Secure the side frames to the floorboard with /-0 x -/ hex-head bolts (), -inch fender washers () and lock nuts (5) as shown (Figure ). Tighten hardware to 8 ft-lb (0.8 N m). 0.. Use the three holes in each of the rear mounting brackets () as templates and drill three 5/6-inch (8 mm) holes through the vehicle body. See preceding CAUTION. 0.. Secure rear mounting brackets () to the side of the vehicle with 5/6-8 x / carriage bolts (0), flat washers () and lock nuts () as shown (Figure ). Tighten all 5/6-inch mounting hardware to 7 ft-lb (.0 N m). Repeat this step for the passenger-side of the vehicle Tighten the /-inch mounting hardware on the front mounting brackets ( and ) to 8 ft-lb (0.8 N m) (Figures and ). Page Cab Kit Installation Instructions (050770)

15 . SECURE SEAT BELT RECEIVER LATCHES Figure Secure Mounting Bracket to Passenger-Side Receiver Latch Figure 5 Secure Mounting Bracket to Driver-Side Receiver Latch.. Secure a mounting bracket (5) to the drive-side receiver latch (6) with a 7/6- x hex-head bolt () and lock nut () through the smaller hole as shown (Figure ). Tighten hardware to 50 ft-lb (67.8 N m)... Secure a mounting bracket (5) to the pass ) with a 7/6- x hex-head bolt (), and lock nut () through the smaller hole as shown (Figure 5). Tighten hardware to 50 ft-lb (67.8 N m)... Remove the seats from the vehicle... In the center of the rear seat support (0), locate the two nut inserts in the frame and use as a guide to drill two 7/6 inch ( mm) holes through the inserts and seat support as shown (Figure 6)..5. Mount the two seat belt receiver latch assemblies () to the bucket seat support with 7/6- x -/ hex-head bolts (), flat washers (), and lock nuts () as shown (Figure 7). Tighten mounting hardware to 0-6 ft-lb ( N m). ENLARGE HOLES TO 7/6-IN ( mm) 0 Figure 6 Enlarge Holes for Seat Belt Receiver Latch Figure 7 Secure Receiver Latches Cab Kit Installation Instructions (050770) Page 5

16 . SECURE SEAT BELTS Figure 8 Secure Seat Belt Retractor.. Secure each seat belt retractor (8) to the brackets (9) on the side frame with one hex-head bolt (), and flanged hex nut (0) as shown (Figure 8)... Secure each seat belt D-loop () to the brackets () with one hex-head bolt (), flat washer (5), flanged hex nut (6) as shown (Figure 9)... Tighten seat belt mounting hardware to 50 ft-lb (67.8 N m). Secure plastic cap (7) to D-loop bolts ()... Secure the seats to the vehicle Figure 9 Secure Seat Belt D-loop Page 6 Cab Kit Installation Instructions (050770)

17 . SECURE WIPER MOTOR TO WINDSHIELD Place a black nylon tee spacer () (with larger diameter end facing away from the motor housing) and nylon spacer () onto the wiper motor shaft as shown (Figure 0)... From inside the cab insert the shaft (8) through the center hole in the bottom of the windshield... Secure the wiper motor to windshield with the seal and nylon washer (0), black washer (5), and nut () supplied with motor. Tighten nut to 0 in-lb (. N m)... Secure wiper motor bracket (7) to the windshield with a /-0 x 5/8 hex-head bolt (), nylon flanged bushing (6), nylon bushing (), washer (), and nylon locknut () as shown (Figure 0). Tighten hardware to 7.5 in-lb (8.5 N m). See following WARNING. ý WARNING Figure 0 Secure Wiper Motor Club Car electric vehicles are designed without a chassis ground. Failure to maintain this chassis isolation could result in a potential fire hazard. The wiper motor must be isolated from the windshield frame. Make sure the nylon spacer and nylon washer are located next to the windshield frame. The wiper motor bracket or hardware can not contact the windshield frame..5. Locate the wiper motor harness () in the drivers-side dash pocket and connect to the wiper motor (5) as shown (Figure )..6. Secure the wire harness to the edge of the windshield frame with two hellerman wire ties () as shown (Figure ) Cab Kit Installation Instructions (050770) Page 7

18 5 5 Figure Connect Wiper Motor.7. Adjust the length of the wiper arm by releasing the clam p () and sliding the wiper arm rod (9) out of the wiper arm support (0). Secure the rod by closing the clamp () as shown (Figure )..8. Remove and retain the screw (7) and nut (8) from the end of the wiper arm. Loosen the small adjusting screw () at the wiper arm pivot point..9. Position the wiper blade to the arm and rotate the wiper blade to a 5 angle from the wiper arm as shown (Figure ). Tighten the small adjusting screw () at the wiper arm pivot point..0. Secure the wiper blade to the arm with the screw (7) and nut (8) removed in step.7. Tighten to 8 in-lb (0.9 N m) Figure Adjust Wiper Arm Length Figure Wiper Blade Installation Page 8 Cab Kit Installation Instructions (050770)

19 NOTE: To remove the wiper arm from the wiper motor once installed can be difficult... Position the wiper arm and blade to the windshield so the end of the wiper blade is / inch (.7mm) from the driver-side edge of the windshield as shown (Figure )... Keep the position of the wiper arm constant while installing the wiper arm () onto the motor shaft spline (8). Grasp the wiper arm with your right hand and place your thumb on top of the portion that secures to the motor spline. Bend the wiper arm (at the knuckle) and align to the motor shaft spline until the proper position/angle is obtained on the windshield as shown (Figure ). Do not push the wiper arm onto the spline until you are sure of the correct position/angle as there is a spring retaining clip that engages the spline when fully installed. / IN. 8 Figure Wiper Arm Installation Cab Kit Installation Instructions (050770) Page 9

20 . SECURE CENTER HIGH MOUNTED STOP LIGHT 5 Figure 5 Secure Center High Mounted Stop Light.. Remove the rear allen-head bolt (), nylon washer (), flat washer (), and locknut (5) from the rear of the roof (Figure 5). Retain the hardware... From inside the cab, remove the passenger seat... Locate the stop light wire harness from behind the passenger seat and route the harness up to center high mounted stop light... Slightly lift up the edge of the roof to push the wire connectors from the wire harness through to the rear..5. Match and connect the stop light wires to the wire harness..6. Secure the center high-mounted stop light () to the rear of the roof with hardware removed in step...7. Working from the stop light towards the passenger side of the cab, press the wire harness between the cab roof and frame. Page 0 Cab Kit Installation Instructions (050770)

21 .8. Continue to route the wire harness down the inside corner of the cab and secure with two p-clips (7) to the sdie frame tabs (8) with two hex-head bolts (9), and locknuts (0) as shown (Figure 6)..9. At the passenger side seat closeout (), remove and retain the hex-head bolt (), flat washer, and hex nut () that secures the passenger side seat closeout to the body..0. Secure the wire harness with one p-clip () using the retained hardware ( and ) (discard the flat washer) at the seat closeout. See following CAUTION. CAUTION Do not route the wire towards the rear of the passenger seat as the seat mounting plate will pinch the wire harness when the seat is down. Make sure harness is routed to the side of the seat as shown (Figure 6) Figure 6 Secure Wire Harness for Center High Mounted Stop Light Cab Kit Installation Instructions (050770) Page

22 5. SECURE INTERIOR MIRROR 5.. From inside the cab, make sure the windshield is free from dirt, dust, and grease. 5.. Tape the paper template (included in this kit) to the windshield to locate the position of the mirror mount () (Figure 7). 5.. Follow the instructions included for the glue, and glue the mirror mount () to the windshield. Remove the template. 5.. After the glue has dried, slide the mirror () onto the mount () and secure with the set screw (). -7/6-IN Figure 7 Secure Interior Mirror 6. SECURE AIR VENTS NOTE: If vents are already installed, proceed to step From inside the cab, press each vent () into the hole in the bottom of the windhsield frame. 6.. Secure each vent with two screws () and lock nuts (). Page Cab Kit Installation Instructions (050770)

23 7. CONNECT BATTERY CABLES Figure 8 Secure Air Vents ý WARNING Electric vehicles: Place Tow/Run switch in the TOW position before disconnecting or connecting the batteries. Failure to heed this warning could result in a battery explosion or severe personal injury. 7.. Connect the battery cables, positive (+) cable first. For electric vehicles, tighten hardware to 0 in-lb (. N m) (Figures through, starting on page 6). Coat terminals with Battery Terminal Protector Spray (CCI P/N 005) to minimize corrosion. QUESTIONS Questions or comments regarding these kit instructions should be referred to your local Club Car dealer or distributor. Please know your vehicle model and have these kit instructions available when you call. Cab Kit Installation Instructions (050770) Page

24 Your Comments Are Appreciated Contact Information (Optional): Name: Title/Company: Address: City: State: Zip: Phone: Fax: I am: Distributor/Dealer Individual Owner Club Car Associate/Representative Technician Golf Course Superintendent Other: Rate Our Publication: In order to help us better serve you, please rate this publication in the following categories: Poor Fair Average Good Excellent. Ease of Understanding. Ease of Finding Information. Clarity of Illustrations/Photos. Index Usability 5. If you are reviewing a Kit Instruction, were all indicated parts included in your kit? Yes / No Your Comments and Suggestions: Please send a copy of this page to: Fax: (706) 8-66 or Tech_Pubs@clubcar.com Thank You! Club Car s Technical Publications Department Cab Kit Installation Instructions (050770)