CONTENTS: TOOLS REQUIRED:
|
|
- Janice Howard
- 6 years ago
- Views:
Transcription
1 CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N RBI77KICK37 1EA. POWER HARNESS P/N RH41PMP 1EA. OVERLAY HARNESS P/N RH41PM 3EA. NUT P/N RFM6NUT 6EA. WIRE TIE P/N RFZIP6 1EA. FUSE 30 AMP P/N RFUSE30 1EA. INSTRUCTIONS P/N RBI77KICK37 TOOLS REQUIRED: *Pick Tool*10mm Socket *Ratchet *Panel Removal Tool* 10mm Nut Driver *Torx T55 Socket Driver*7mm Wrench*7mm Nut Driver*Phillips Screwdriver 77KICK37 9/16/2008 Page 1 of 10
2 Dodge Caliber, Jeep Compass Radio Removal 1. Set the parking brake and with the key on but not running put the car in low gear (automatic transmission) or fourth gear (manual transmission). 2. Using a panel removal tool pry loose the shifter bezel or rubber boot (manual transmission) Fig Continue to step 12 Fig. 1 Jeep Patriot Radio Removal 4. Pull the rubber door molding away from door openings to reveal the edges of the A pillar post covers. Fig Using a pick tool pry open the screw covers on both passenger s and driver s side A pillar post covers and remove the screws securing the A pillar post covers. Fig. 3 Fig. 2 Fig. 3 77KICK37 9/16/2008 Page 2 of 10
3 Jeep Patriot Radio Removal (continued) 6. Starting at one end and working across the dash, use a panel removal tool to gently pry up on the dash speaker cover to release the metal fasteners. Fig Starting at the end closest to the windshield pull the plastic panel in the center of the dash loose. Fig. 8 Fig. 7 Fig Remove the two screws securing the radio top of the radio bezel. Fig Set the parking brake and with the key on but not running put the car in low gear (automatic transmission) or fourth gear (manual transmission). 10. Using a panel removal tool pry loose the inner shifter bezel or rubber boot (manual transmission) 11. Remove the two screws securing the outer portion of the shifter bezel and pry the bezel loose. Fig. 10 Fig. 9 Fig KICK37 9/16/2008 Page 3 of 10
4 Jeep Patriot Radio Removal (continued) 12. Starting at the bottom use a panel removal tool to pry loose the radio bezel. Fig Using a 7mm wrench remove the four screws securing the HVAC controls to the back of the radio bezel. Fig. 12 Fig. 11 Fig Disconnect the hazard light switch and set the bezel aside. Fig Remove the four 7mm screws securing the radio, pull the radio from the dash and disconnect the wiring. Disconnect the antenna cable by pulling the locking antenna connector away from the radio. Caution: Pulling the antenna cable straight out of the radio without pulling on the locking antenna connector could damage the cable or radio. Fig. 14 Fig. 13 Fig KICK37 9/16/2008 Page 4 of 10
5 Power Harness Installation 16. Lift up on the B pillar post cover and then pull it towards the center of the car to remove. Fig Using a panel removal tool gently pry up the threshold/kick panel along the bottom of the front and rear door openings to release fasteners and remove panel. Fig. 16 Fig. 15 Fig Find the black plastic fastener securing the driver s side kick panel under the instrument panel and unscrew it. Fig Pull backwards on the kick panel to remove it. 20. Pull the cover of the foot rest to snap it loose. Fig. 18 Fig. 17 Fig KICK37 9/16/2008 Page 5 of 10
6 Power Harness Installation (continued) 21. Using a 10mm nut driver remove the nut securing the base of the foot rest. Fig Pull the front edge of the carpet down past the accelerator pedal. 23. Find the small drain hose coming from the HVAC housing that penetrates the floor pan near the accelerator pedal and pull it inside the vehicle. 24. Locate the battery access cover under the hood and remove according to the instructions printed on top of the panel. Fig. 20 Fig. 19 Fig Disengage the metal fasteners on the air filter box cover and move the cover to one side out of the way. It is not necessary to disconnect any of the ducting connected to the cover. Fig Remove the air filter and set aside. Pull straight up on the air filter housing and remove it from the vehicle. Fig. 22 Fig. 21 Fig KICK37 9/16/2008 Page 6 of 10
7 Power Harness Installation (continued) 27. Using a 10mm nut driver loosen and remove the nut on the positive battery accessory lug. 28. Connect the ring terminal of the power harness (PN RH41PMP) to the lug and retighten the nut. Fig Detach the white three pin connector from the harness and route the wire toward the rubber grommet that had the HVAC drain hose coming through it next to where the steering column comes through the fire wall securing with wire ties where needed. Fig. 24 Fig. 23 Fig Pass the power wire through the grommet. 31. Find where the wire is coming through the fire wall on the interior of the vehicle. Pull enough wire through to allow the end to reach the area where the foot rest was mounted. While holding the power wire, reinstall the hose through the grommet so that the power wire is captured between the hose and the grommet. Fig Install the supplied three pin connector by inserting the terminals on the end of the power wire into the open holes in the back of the connector until they click and lock. Fig. 26 Fig. 25 Fig KICK37 9/16/2008 Page 7 of 10
8 Amplifier Installation 33. Plug the power wire connector on amplifier harness (PN RH41PM) to the connector you installed on the wires coming from the fuse block. Fig Route the wire harness up from below the steering column to the radio cavity. 35. Pass the radio harness connecter behind the metal framework indicated by the arrow in Fig Connect the male radio harness connecter to the female connecter of the amp harness and tuck this connection into the void directly below the area where the radio mounts to avoid interference with radio during reinstallation. 37. Route male connector of the amp harness back around the beam as the radio harness originally was. Fig You can now connect the radio to the amp harness and reconnect the antennae wire and reinstall the radio. Fig. 27 Fig Route the subwoofer harness along the edge of the front and rear door openings securing with wire ties where needed. Fig Using a Torx T55 driver, remove the two bolts securing the bottom back seat cushion and remove the cushion from the vehicle. Fig. 30 Fig. 29 Fig KICK37 9/16/2008 Page 8 of 10
9 Amplifier Installation (continued) 41. Lift the load floor and rotate the right side to allow it to be removed from the vehicle. Fig Pull the molded fabric cover loose from between the rear seat and the spare tire. Fig. 32 Fig. 31 Fig Route the wire under the rear quarter panel cover and out through the relief near where the rear seat belt is bolted to the floor. Fig Continue routing the wire harness along the bottom of the car to the passenger s side and pull it up between the seat and cargo floor. 45. Pull up on the rear quarter panel and slide the wire harness behind it. There is a notch the wire can be placed in. Fig. 34 Fig. 33 Fig KICK37 9/16/2008 Page 9 of 10
10 Amplifier Installation (continued) 46. Plug the amplifier in and install it over the three studs. Fig Place the ground wire over the stud closest to the seat and install the supplied nuts and tighten. Fig. 36 Fig. 35 Fig. 36 Important! If you have previously installed a Kicker subwoofer kit (#77KICK14 or #77KICK22) you would have tapped into the left front door speaker wires in the kick panel area. Disconnect those wires and reconnect them to the brown and green wires in the 4.1 amplifier harness. The brown wire connects to the brown wire and the green wire connects to the green wire. Fig. 37 Fig Reinstall all previously removed parts in reverse order. Torque the rear seat bottom cushion bolts to 60 ft. lbs 49. Install supplied fuse in fuse holder under hood. 77KICK37 9/16/2008 Page 10 of 10
CONTENTS: 1EA. SUBWOOFER HARNESS 2PIECE TOOLS REQUIRED:
CONTENTS: 1EA. SUBWOOFER ENCLOSURE 1EA. SUBWOOFER HARNESS 2PIECE 2EA. T-TAP 1EA. FUSE 30 AMP 6EA. WIRE TIES 1EA. INSTRUCTIONS P/N 77KICK14SUBASSEMBLY P/N RHPM1 P/N RFTTAPB P/N RFUSE30 P/N RFZIP6 P/N RBI77KICK14
More informationTOOLS REQUIRED: Panel Removal Tool Phillips Screwdriver 10mm Nut Driver Ratchet 10mm Socket 7mm Wrench 7mm Nut Driver Straight Screwdriver
CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N MPDSP039AA 1EA. OVERLAY HARNESS P/N RH41LX10 3EA. 7MM SCREWS P/N RF7MM 6EA. WIRE TIE P/N RFZIP6 1EA. 30 AMP FUSE P/N RFUSE30 1EA. INSTRUCTIONS
More informationCONTENTS TOOLS REQUIRED:
CONTENTS 1EA. FIVE CHANNEL AMPLIFIER P/N MPDSP033AA 1EA. AMPLIFIER BRACKET P/N RM11JK41 1EA. POWER HARNESS P/N RH41JKP 1EA. OVERLAY HARNESS P/N RH41JK 1EA. FUSE 30 AMP P/N RFUSE30 6EA. WIRE TIE P/N RFZIP6
More informationPWRA215. Designed for 2015 and newer Jeep Wrangler two door with base audio. T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY
PWRA215 Designed for 2015 and newer Jeep Wrangler two door with base audio T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY 200 WATT AMP BRACKET ASSEMBLY POWER HARNESS 2015 Stillwater Designs PWRA215
More informationImportant! The subwoofer system is designed to be used only with the rear seat in the up position only.
Important! The subwoofer system is designed to be used only with the rear seat in the up position only. CONTENTS 1EA. SUBWOOFER ASSEMBLY 2EA. BRACKET LOWER 2EA. BRACKET UPPER 1EA. OVERLAY HARNESS 2EA.
More informationAudio System Upgrade Package Dodge Magnum, Chrysler 300C, Dodge Charger Jeep Commander (Premium Audio Only)
2005-2006 Dodge Magnum, Chrysler 300C, Dodge Charger 2005-2006 Jeep Commander (Premium Audio Only) 2005-2006 Dodge Ram (Regular Cab, Quad Cab, Mega Cab) 2005-2007 Jeep Grand Cherokee (Premium sound) TOOLS
More informationCONTENTS TOOLS REQUIRED: *Ratchet*13mm Socket*10mm Socket*Phillips Screwdriver*Pliers*Panel Removal Tool. Subwoofer Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N 77KICK24SUBASSEMBLY 1EA. 200 WATT AMP P/N RE08BTL200R 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER 2EA. T-TAP P/N RFTTAPB 1EA. FUSE 30 AMP
More informationCONTENTS TOOLS REQUIRED: *Ratchet*13mm Socket*10mm Socket*Phillips Screwdriver*Pliers*Panel Removal Tool. Subwoofer Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N 77KICK40SUBASSEMBLY 1EA. 200 WATT AMP P/N RE08BTL2000R 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER 2EA. T-TAP P/N RFTTAPB 1EA. FUSE 30
More informationCONTENTS TOOLS REQUIRED:
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N 77KICK13SUBASSEMBLY 1EA. SUB BRACKET P/N 05030060AA 1EA. 200 WATT AMP P/N REBTL200 1EA. AMP BRACKET P/N RMDR 1EA. POWER HARNESS P/N RHRAMP 1EA. OVERLAY HARNESS P/N
More informationPRAMCQ13. Designed for Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles
PRAMCQ13 Designed for 2013 2017 Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles Subwoofer Alternate Amplifier Bracket Amplifier Subwoofer Harness Subwoofer Amplifier
More informationSWRA211. T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY 200 WATT AMP BRACKET ASSEMBLY POWER HARNESS OVERLAY HARNESS.
SWRA211 Designed for 2011-2014 Jeep Wrangler two door with base audio or premium audio T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY 200 WATT AMP BRACKET ASSEMBLY POWER HARNESS 2012 Stillwater
More informationPCAMA13MY. Designed for Chevrolet Camaro vehicles with MyLink. Subwoofer Assembly. Subwoofer Bracket Wire Ties x6 Rubber Bumper
PCAMA13MY Designed for 2013-2015 Chevrolet Camaro vehicles with MyLink Subwoofer Assembly Subwoofer Harness Adapter Harness Subwoofer Bracket Wire Ties x6 Rubber Bumper 2012 Stillwater Designs PCAMA13MY-A3-20151028
More informationAudio System Upgrade Package 2007-UP Jeep Wrangler (Premium Audio) 4-Door & 2- Door Operating and Installation Instructions
2007-UP Jeep Wrangler (Premium Audio) 4-Door & 2- Door Operating and Congratulations, you just purchased one of the most sophisticated 32 bit digital audio amplifiers available today. Fortunately, all
More informationPF150SC15. Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Stillwater Designs PF150SC15-A
PF150SC15 Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs PF150SC15-A2-20160502
More informationDesigned for 2005 & newer Ford Mustang (Not compatible with Convertible)
Designed for 2005 & newer Ford Mustang (Not compatible with Convertible) SMUS05 Subwoofer Enclosure Assembly Power Harness Body Harness Input Adapter Wire Ties x6 M6 Nut 25A Fuse Wire Taps x2 SMUS05 A.2
More information*Phillips Screwdriver *10mm Nut Driver *10mm Socket *Ratchet *Three Inch Putty Knife *Panel Removal Tool *10mm Wrench CONTENTS:
TOOLS REQUIRED: *Phillips Screwdriver *10mm Nut Driver *10mm Socket *Ratchet *Three Inch Putty Knife *Panel Removal Tool *10mm Wrench CONTENTS: 1EA. SUBWOOFER ASSEMBLY 1EA. 100 WATT AMP ASSEMBLY 1EA. WIRE
More information*Phillips Screwdriver *10mm Nut Driver *8mm Nut Driver*10mm Socket *Ratchet *Three Inch Putty Knife*Panel Removal Tool *10mm Wrench
TOOLS REQUIRED: *Phillips Screwdriver *10mm Nut Driver *8mm Nut Driver*10mm Socket *Ratchet *Three Inch Putty Knife*Panel Removal Tool *10mm Wrench CONTENTS: 1EA. SUBWOOFER ASSEMBLY P/N 05030280AA 1EA.
More informationPSIEXT16I. Designed for 2016 and newer 1500 Series and Heavy Duty GM Silverado/Sierra Double Cab vehicles with 7 inch touchscreen radio
PSIEXT16I Designed for 2016 and newer 1500 Series and Heavy Duty GM Silverado/Sierra Double Cab vehicles with 7 inch touchscreen radio Not compatible with Bose Audio Not compatible with 4.2 inch radio
More informationDesigned for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System. M6 Bolt X 2
SF150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System Subwoofer Assembly Amplifier Relocation Bracket (not used on non Sony trucks)
More informationSCAMA10. Designed for Chevrolet Camaro vehicles. Subwoofer Assembly. Subwoofer Bracket Wire Ties x6 Wire Taps x2 Rubber Bumper
SCAMA10 Designed for 2010-2015 Chevrolet Camaro vehicles Subwoofer Assembly Subwoofer Harness Subwoofer Bracket Wire Ties x6 Wire Taps x2 Rubber Bumper 2012 Stillwater Designs SCAMA10-A3-20151028 M6 Nut
More informationTOOLS REQUIRED: *Pliers*Panel Removal Tool*Crimpers*Wire Strippers*Ratchet*10mm Socket*#2 Phillips Bit*Drill*18mm socket*19mm socket
CONTENTS: 1EA. SUBWOOFER ASSEMBLY P/N 77KICK20SUBASSEMBLY 1EA. OVERLAY HARNESS P/N RHLX 2EA. LOWER BRACKET P/N RMLX 8EA. #8X1 SCREW P/N RFS81P 2EA. LOCKING NUT 18MM P/N RFLOCKNUT18 2EA. WASHER P/N RFW2
More informationSRAMCQ09. Designed for Dodge Ram vehicles Stillwater Designs SRAMCQ Subwoofer. Subwoofer Harness.
SRAMCQ09 Designed for 2009-2018 Dodge Ram vehicles Subwoofer Alternate Amp Bracket Subwoofer Harness Subwoofer Amplifier Wire Ties x 6 Adapter Harness Subwoofer Power Harness Bolt (only for solid rear
More informationPSIEXT14. Subwoofer Assembly. Subwoofer Power Harness. Subwoofer Body Harness. 25A Fuse Wire Ties x 6 Washers x 2
PSIEXT14 Designed for 2014 and newer Chevrolet Silverado & GMC Sierra Double-Cab 1500 series with base radio 2015 and newer Chevrolet Silverado & GMC Sierra Double-Cab 2500/3500 with base radio (Not compatible
More informationPFSDC12. Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Stillwater Designs PFSDC12-A Subwoofer Enclosure
PFSDC12 Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Subwoofer Enclosure Amplifier/Bracket Assembly Subwoofer Power Harness Amplifier Harness Subwoofer Harness Amplifier Power Harness
More informationPSICRE14. Subwoofer Assembly. Subwoofer Power Harness. Subwoofer Body Harness 25A Fuse Wire Ties x Stillwater Designs PSICRE14-A
PSICRE14 Designed for 2014 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 1500 series with base radio 2015 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 2500/3500 with base radio (Not compatible
More informationINSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT
PART NUMBER: 0000-89-N30 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT APPLICABLE MODELS: 2016 > CX-9 PACKAGE CONTENTS: INSTALLATION INSTRUCTIONS QTY 1 CABLE TIE MOUNT QTY
More informationSSUTAYU15. Designed for 2015 and newer Chevrolet Tahoe/Suburban and GMC Yukon/Yukon XL vehicles
SSUTAYU15 Designed for 2015 and newer Chevrolet Tahoe/Suburban and GMC Yukon/Yukon XL vehicles Subwoofer Assembly Subwoofer Harness Subwoofer Power Harness 2018 Stillwater Designs SSUTAYU15-20180313 Wire
More informationPART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:
More informationSF150C09. Designed for Ford F150 Super-Crew vehicles (not compatible with trucks that have Sony Factory Premium Audio) Subwoofer Assembly
SF150C09 Designed for 2009-2014 Ford F150 Super-Crew vehicles (not compatible with trucks that have Sony Factory Premium Audio) Subwoofer Assembly Subwoofer Power Harness Subwoofer Body Harness M6 Bolts
More informationINSTALLATION INSTRUCTIONS
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies
More informationTOYOTA LAND CRUISER 2003 DVD VES
LEXUS LX470 Section I Installation Preparation Part Number: PT296 6002D 03/16 (LC) PT296 6002L 03/16 (LX) Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 FPD Assembly
More informationJeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # )
Jeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # 9002-8857) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Power
More informationJeep Wrangler Rear Vision Camera, 2007 Current (Kit # )
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8837) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts Program Module 22--pin
More informationxpressstart Mercedes Solution Mercedes Benz S and CL Class
DIGITAL REMOTE START SYSTEM WWW.XPRESSKIT.COM MADE IN THE USA xpressstart Mercedes Solution 2007-2012 Mercedes Benz S and CL Class Tools you will need -T-25 Torx Driver -Panel Removal tool -3/4 Drill bit
More informationJeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # )
Items Included in the Kit Jeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # 9002-8848) Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA (for factory display radio)
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationJeep Wrangler Rear Vision Camera, 2007 Current (Kit # )
Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions 22--pin white connector w/ video RCA (for factory display radio) Jeep Wrangler Rear Vision
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationINSTALLATION INSTRUCTIONS. Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # )
Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # 9002-8847) Items Included in the Kit Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26031 2004 ODYSSEY Issue Date AUG 2003 NOTE: You cannot install the subwoofer in a vehicle equipped with both an under seat Navigation
More informationSCHAL08. Designed for Dodge Challenger vehicles. Subwoofer Assembly. 200W Amplifi er. Wire Harness
SCHAL08 Designed for 2008-2014 Dodge Challenger vehicles Subwoofer Assembly 200W Amplifi er Wire Harness 2012 Stillwater Designs SCHAL08-A3-20140930 Wire Ties x6 25A Fuse #8 Sheet Metal Screws x4 Body
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27363 ODYSSEY Issue Date SEP 2004 PARTS LIST Compact Subwoofer Kit: P/N 08A39-5E1-010 4 Flange bolt, 6 x 12 mm Subwoofer 3 Cushion tapes
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationSSICRE14. Subwoofer Assembly. Subwoofer Body Harness. Subwoofer Power Harness. Fuse Wire Ties x 6 Wire Taps x 2 Adaptor Harness
SSICRE14 Designed for: 2014 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 1500 series with base or premium radio 2015 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 2500/3500 with base or premium
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2008 CR-V Publications No. AII 35843-38422 Issue Date DEC 2007 PARTS LIST Caution label Remote Engine Starter Kit P/N 08E91-E22-100B Transmitter
More informationINSTALLATION INSTRUCTIONS
9002-6513 Rear Vision System W/ Zoom Aftermarket and Factory 8.4 Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 2012 RAM (Part B) 2013 Current RAM (Part A) NOTE:
More informationInstallation instructions, accessories RTI S80
Installation instructions, accessories Instruction No 8685714 Version 1.0 5 Part. No. RTI S80 Volvo Car Corporation RTI S80-8685714 - V1.0 Page 1 / 25 Equipment A0000161 A0000162 A0801178 D8802049 Page
More informationTOYOTA SIENNA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More information* * APPLICABLE MODELS: 2016 > CX-3
PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS
GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS PART NUMBERS: APPLICABLE MODELS: 0000-89-G14A (PORT) Electrochromic Mirror Kit w/ Compass/Temp/HomeLink 2004 Mazda 3 0000-8C-G14A (PDC) KIT CONTENTS: ITEM
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More informationSFSDC08. Designed for 2008-present Ford F250/F350 Super Crew vehicles. Adaptor Harness. Subwoofer Power Harness
SFSDC08 Designed for 2008-present Ford F250/F350 Super Crew vehicles Subwoofer Enclosure Subwoofer Harness Adaptor Harness Wire Ties Wire Taps Fuse Factory Amplifier Relocation Bracket, Nut and Bolt Subwoofer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27336 ODYSSEY Issue Date SEP 2004 PARTS LIST 15 Black wire ties Backup Sensor Attachment Kit P/N 08V67-SHJ-100A Backup sensor control
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationJeep JK Wrangler XHD Rear Tire Carrier
Contents: 1. Frame (1) 2. Pivot Mount (1) 3. Latch Mount (1) 4. Lug Nuts (3) 5. Catch Pin (1) 6. M12 Washer (18) 7. M12 x 30 Hex Bolt (14) 8. Brake Light Mount (1) 9. Snap Ring (1) 10. Rub Strip (1) 11.
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B. Display bracket.
INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2006 PILOT All 30502 Issue Date SEP 2005 PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B Display
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationINSTALLATION INSTRUCTIONS
2007-Current Jeep Wrangler 360º System for Aftermarket display (Kit # AVMS-3700v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2004 TSX BII 24811 Issue Date APRIL 2003 PARTS LIST Attachment Kit P/N 08B23-SDA-101A Monitor bracket harness FM
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart Service Part Number. 1 1 Mirror Assembly w/ Compass 1
AUTO PART NUMBER: 0000 8C P4 (DIO)/ 0000 89 P25 (PIO) REQUIRED COMPONENTS: INSTALLATION KIT: 2 SA Harness - 2 Conductor 3 0 Wire Ties 4 Wire Cover 5 A-Pillar Tether Clip (D09W-6862) 6 3 Foam Tape 7 3 Electro-Tap(wire
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM (EXCEPT LX) 2006 ODYSSEY All 30392 Issue Date AUG 2005 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SHJ-100
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More informationINSTALLATION INSTRUCTIONS
2007-Current Jeep Wrangler 360º System for Factory Display Radios (Kit # AVMS-3701v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the
More informationConflicts: Vehicles with a sunroof
Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:
More informationINSTALLATION INSTRUCTIONS
2007-Current Jeep Wrangler 360º System for Factory Display Radios (Kit # AVMS-3701) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR 5005
DRIVING LIGHTS for FLHT/FLHX/FLHR 5005 PARTS INCLUDED 1 Right Driving Light Assembly 1 Left Driving Light Assembly 1 Right Driving Light Bracket 1 Left Driving Light Bracket 4 Driving Light Bracket Plugs
More informationSADDLEBAG AUDIO WIRE HARNESS KIT P/N
SADDLEBAG AUDIO WIRE HARNESS KIT P/N 2880986 APPLICATION ALL INDIAN MOTORCYCLES WITH BOTH TRUNK AND SADDLEBAG AUDIO INSTALLED BEFORE YOU BEGIN Read these instructions and check to be sure all parts and
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA SIENNA TRAILER WIRE HARNESS Preparation
Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM ACCORD 2-DOOR (LX/EX L4, LX V6) AII 25749 Issue Date FEB 2004 PARTS LIST Double-sided adhesive tape XM Radio Attachment Kit : P/N
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationInstrument Panel Assembly Replacement. Fig. 14 Battery Negative Cable Removal/Installation
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Chrysler Truck PT Cruiser L4-2.4L VIN B Conversion
More informationSCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More information