Model 873 COMBINE ADAPTER

Transcription

1 Model 873 COMBINE ADAPTER For 963, 972, 973 & 974 Headers on: Case Combines New Holland Combines John Deere Combines Lexion Combines Agco Combines PARTS CATALOG Form Issue 09/06 Sugg. Retail: $10.00

2 Inside Front Cover (blank)

3 Model 873 COMBINE ADAPTER PARTS CATALOG 1 CONTENTS Frame and Float Group... 2, 3 Hydraulics... 4, 5 Hydraulics Pump... 6 Hydraulics Valve Block... 7 Gear Drive... 8, 9 Selector Valve and Center Links (Attachment)... 10, 11 Feed Draper & Deck Retracting Tine Drum... 16, 17 Case 20 Series Combines Adapter Completion Parts... 18, 19 Header Completion Parts... 20, 21 Case AFX & New Holland CR/CX Series Adapter Completion Parts... 22, 23 Header Completion Parts... 24, 25 John Deere Combines Adapter Completion Parts (Pre 50 Series & 50 Series Models)... 26, 27 Header Completion Parts (All Models)... 28, 29 Adapter Completion Parts (60 Series Models)... 30, 31 Lexion Combines Adapter Completion Parts... 32, 33 Header Completion Parts Auto Reel Speed/Height Group... 38, 39 Agco Combines Adapter Completion Parts... 40, 41 Header Completion Parts... 42, 43 Decals... 44, 45 Driveline... 46, 47 Float Optimizer (Attachment): Case, Agco & John Deere (50 & 60 Series) Combines Float Optimizer (Attachment): New Holland CR/CX Combines Float Optimizer (Attachment): John Deere (Prior to 50 Series) Combines Float Optimizer (Attachment): Lexion Combines Float Indicator (Attachment) NUMERICAL LIST SUGGESTED STOCKING LIST... 72, 73 L/H - left hand (Determined from Operator's position, facing forward.) R/H - right hand I.D. - inside diameter O.D. - outside diameter ABBREVIATIONS A/R - as required (quantity varies) REF - reference, part number called up elsewhere in catalog NC - national coarse thread NF - national fine thread NSS not serviced separately NOTE: Common hardware is not illustrated. Alphabetic references are used to designate position and description of these items. When ordering, be sure the complete and proper serial number is given. SERIAL BREAKS The side of the serial number on which the dash (-) appears determines whether the part is used "up to" or "after" the serial number given. Example: Used on machines up to and including serial number Used on machines including and after serial number BOLDED PART S INDICATE REVISIONS OR ADDITIONS SINCE LAST PRODUCTION YEAR.

4 2 FRAME AND FLOAT GROUP

5 FRAME AND FLOAT GROUP 3 REF PART DESCRIPTION QTY SERIAL 1 REF FRAME Adapter, not serviced MEMBER lower pivot arm, L/H, includes items MEMBER lower pivot arm, R/H, includes items 3 6 * (see notes) MEMBER lower pivot arm, R/H, includes items 3 6 ** (see notes) BEARING needle, for item SEAL install with lip facing outwards BEARING needle, for item 2, front, c/w seals, seals face outwards FITTING lube, 1/4 NC PIN - straight PIN pivot RETAINER (was ) RETAINER pivot pin, L/H RETAINER pivot pin, R/H SPRING extension, outer INSERT spring MEMBER float MEMBER float (includes item 39) INSERT spring INSERT spring SPRING extension, inner BAR - spacer WASHER 3/4 ID, hardened PIN clevis PIN cotter LOCK LOCK PIN lynch PIN spring PIN clevis PIN - straight PIN clevis STOP L/H STOP L/H STOP R/H STOP R/H BUMPER rubber, down stop PLATE shim PLATE shim PLATE stop PLATE stop BOLT plow, #3 HD, 1/2 NC x HOLDER driveline BOLT hex head, 3/4 NC x 20-1/2 inch, thread full length NUT regular hex, 3/4 NC INSERT spring, for 21 headers with no inner spring INDICATOR header angle, see NOTE PIN safety lock PLATE reinforcement (welded)...4 A BOLT round head, square neck, 3/8 NC x 1 inch B NUT lock, smooth flange, 3/8 NC distorted thread C WASHER flat, 20.6 mm ID D BOLT round head, square neck, 3/8 NC x ¾ inch E NUT lock, smooth flange, 1/2 NC distorted thread F NUT hex jam, 5/8 NC distorted thread NOTES: 1. Repair part will have cut-out at top mounting hole. For Case AFX/New Holland CR & CX Combines, remove this cut-out to enlarge hole. See page 22 for mounting details. * JD, Case 2300 Series, NH CR 970/980 & Lexion adapters only. ** Used for all serial numbers on Combines except those listed at *. For combines listed at *, used & Up.

6 4 HYDRAULICS

7 HYDRAULICS 5 REF PART DESCRIPTION QTY SERIAL HOSE R/H tank to pump input CLAMP hose, for item VALVE - check REF PUMP hydraulic, see page 6 for service parts BUSHING spline, 18 teeth FITTING hydraulic, 90º elbow, 9/16 O-ring x 3/8 tube O-RING for 9/16 fitting HOSE hydraulic FITTING hydraulic, run tee, 7/8 O-ring x 5/8 tube x 9/16 O-ring run HOSE hydraulic LINE hydraulic, steel LINE hydraulic, steel LINE hydraulic, steel LINE hydraulic, steel REF VALVE hydraulic, combination, see page 7 for service parts FITTING hydraulic, connector, 7/8 O-ring x 5/8 tube O-RING for 7/8 fitting FITTING hydraulic, connector, 1-1/16 O-ring x 3/4 tube O-RING for 1-1/16 fitting FITTING hydraulic, 90º elbow, 7/8 O-ring x 5/8 tube O-RING for 7/8 fitting FITTING hydraulic, 45º elbow, c/w o-ring, 5/8 O-ring x 5/8 tube HOSE hydraulic MOTOR hydraulic, drum drive SEAL KIT for drum motor HOSE hydraulic HOSE hydraulic FITTING hydraulic, 90º elbow, 1-1/16 O-ring x 3/4 tube O-RING for 1-1/16 fitting HOSE hydraulic KEY woodruff, for item FILTER ELEMENT- (LHA #SPE-15-10), see note 1 re: substitution FILTER ASSEMBLY - with head GAUGE oil dipstick COVER valve FITTING hydraulic, 45º swivel elbow, 3/4 O-ring x 3/4 tube PLUG hydraulic c/w item O-RING hydraulic, SAE J515 Type 1, Nitrile HOLDER hydraulic lines, steel HOLDER hydraulic lines, steel MOTOR draper drive KIT seal, for draper drive motor WASHER REF ARM for item 40, see adapter completion packages REF DRIVE gear, see pages 8 & PLUG hex head, c/w 9/16 o-ring (50219) SLEEVE plastic HOSE hydraulic... 1 A WASHER lock, 12.5mm ID B NUT jam, hex, M12 C BOLT socket hd, M x 30mm D WASHER lock, M8 E WASHER flat, 8.7mm ID F BOLT hex head, M x 25mm G BOLT round hd, sq. nk, 3/8 NC x 3/4 H NUT lock, smth flng, 3/8 NC dist. thd J BOLT rnd hd, sq. nk, 3/8 NC x 1-1/2 K BOLT hex hd, smth flng, 3/8 NC x 3/4 L SCREW self tapping, 3/8 NC x 5/8 P REF Pressure to Header R REF Return from Header NOTES: 1.MacDon filter element may be substituted in this application.

8 6 HYDRAULICS PUMP REF PART DESCRIPTION QTY SERIAL * PUMP hydraulic, complete KIT seal (was ) KEY woodruff RING retaining, internal WASHER backup WASHER lock, 12.5mm ID NUT jam, hex M PIN dowel WASHER flat BOLT hex head, M10 x 180 mm... 4

9 HYDRAULICS VALVE BLOCK 7 REF PART DESCRIPTION QTY SERIAL * VALVE block KIT seal, for valve block VALVE check, CV1, cartridge CV N PLUG hex socket head, 7/16 O-ring (50023) PLUG hex head, 9/16 O-ring (50219) VALVE needle, cartridge MR10-20B-0-N PLUG hex socket head, VALVE 2 way, cartridge PD N VALVE pressure compensator, cartridge EC P VALVE relief, cartridge RV50-26A-0-P KIT ball handle kit... 1

10 8 GEAR DRIVE (Operating position 180 to as shown) & (Operating position approximately 90 counter-clockwise to as shown) (Operating position as shown)

11 GEAR DRIVE 9 REF PART DESCRIPTION QTY SERIAL DRIVE gear, complete: Case 2300 Series, JD Level Land prior to 50 Series DRIVE gear, complete: JD Level Land 50 Series and up & Contour Master, Agco DRIVE - gear, complete: New Holland CR & CX, Case AFX DRIVE - gear, complete: Lexion HOUSING gear drive, with one washer item 3 & one plug, item BREATHER oil plug WASHER flat...see note (1) PLUG oil, DIN see note (2) PLUG oil, magnetic GASKET gear drive housing SEAL shaft BEARING ball RING retaining, external KEY shaft SHAFT hex bore, for drive SHAFT extended, 21 tooth spline bore, for drive SHAFT 21 tooth spline bore, for drive SHAFT 6 tooth spline bore, for drive GEAR for drives , and GEAR for drive BEARING ball GEAR for drives , and GEAR for drive SEAL shaft HOUSING gear drive PIN housing BOLT socket head, M8 x 28 mm RING centering GAUGE oil level sight glass... 1 NOTES: (1) Quantities for item 3 Washer: Drives & = 5, Drive = 4, Drive = 3 (2) Quantities for item 4 Plug: Drives & = 2, Drive = 1, Drive = 0

12 10 SELECTOR VALVE & CENTER LINK

13 SELECTOR VALVE & CENTER LINK 11 REF PART DESCRIPTION QTY SERIAL C1837 HEADER TILT KIT complete, Case 2300 Series Combines...OPT C1838 HEADER TILT KIT complete, NH CR/CX, CNH AFX Combines...OPT (Used on 2003 and older combines) B4399 HEADER TILT KIT complete, NH-CR/CX, CNH AFX Combines...OPT (Used on 2004 and newer combines) C1839 HEADER TILT KIT complete, Lexion Combines...OPT C1840 HEADER TILT KIT complete, John Deere Combines...OPT C1931 HEADER TILT KIT complete, Agco Combines...OPT NOTE: 1. Kits (B and C numbers) are available through Wholegoods only. 2. For New Holland CR/CX and NH AFX combines with integral control, items 14, 21, 22, 23 are not required VALVE selector, kit (includes valve & harness) VALVE selector KIT seal, for selector valve (complete) CYLINDER hydraulic, center link SEAL KIT for cylinder HOSE hydraulic, to center link cylinder HOSE hydraulic, to combine couplers FITTING hydraulic, connector FITTING hydraulic, elbow, FITTING hydraulic, elbow, 45 - quantity 5 for Lexion PIN clevis PIN lynch CLAMP - wiring HARNESS wiring, selector valve to item 12 or HARNESS wiring, selector valve to item 12 or HARNESS wiring, fore-aft/header tilt, from header to 31 pin connector HARNESS wiring, fore-aft/header tilt, from 31 pin connector to item SWITCH electrical, mounted inside combine, see note REF SUPPORT selector valve, see header completion package REF HOSE hydraulic, reel fore-aft, aft REF HOSE hydraulic, reel fore-aft, fore JOINT ASSEMBLY mechanical center link B2701 HEADER ANGLE MECHANICAL ADJUSTMENT KIT...OPT see note 1 above SUPPORT switch mount HARNESS wiring, fore-aft/header tilt, from item 11 to combine cab... 1 see note HARNESS wiring, cigar lighter adapter, see note HOLDER harness, see note SHIM selector valve FASTENER cable tie, black COVER selector valve COVER selector valve CARTRIDGE valve CARTRIDGE valve COIL valve COIL valve COIL 12V DC DS for selector valve A BOLT hex head, 1/4 NC x 2-3/4 inch B NUT lock, 1/4 NC C SCREW self tapping, 3/8 NC x 5/8 inch - Case 2300 Series Combines - John Deere & Agco Combines - New Holland CR/CX, CNH AFX, John Deere, Agco and Lexion Combines - New Holland CR/CX, CNH AFX, and John Deere & Agco Combines - New Holland CR/CX, and CNH AFX Combines

14 12 FEED DRAPER & DECK

15 FEED DRAPER & DECK 13 REF PART DESCRIPTION QTY SERIAL NOTE: There are three deck sizes: 38, 45 and 56 (approximate feed draper width). Combines using each size are as follows: 38 Case 60 & 66 Series / New Holland CR 920/940/960 / Gleaner 45 Case 2377, 80 & 88 Series / Lexion 450, 470 & 475 / Case AFX / New Holland CR 970/980 / Challenger 660 / MF John Deere* / New Holland CX / Lexion 460, 465, 480 & 485 / Challenger 670 / MF 9790 * Some John Deere CTS Combines with dust shields in rice applications may have been converted to 45 decks. Check feed draper width carefully before ordering parts that are specific to one deck size PAN - feed draper, 38 deck, includes item PAN feed draper, 45 deck, includes item PAN - feed draper, 56 deck, includes item ROD - idler adjuster SUPPORT - idler rod SPRING - idler tension TUBE - idler roller, 38 deck TUBE - idler roller, 45 deck TUBE - idler roller, 56 deck SHAFT - idler roller, 38 deck SHAFT - idler roller, 45 deck SHAFT - idler roller, 56 deck BEARING - ball SEAL - bearing SPACER - tube ARM - idler FITTING - lubrication, ROLLER drive, 38 deck ROLLER drive, 45 deck ROLLER drive, 56 deck SUPPORT - drive roller BEARING - ball, with lock collar FLANGE - bearing, cropped FLANGE - bearing, cropped (lube fitting removed) COVER - bearing, cropped FITTING - lubrication SUPPORT rear deflector, left SUPPORT rear deflector, right WASHER - flat SPACER - tube DRAPER feed, 38 deck, includes item DRAPER feed, 45 deck, includes item DRAPER feed, 56 deck, includes item CONNECTOR KIT - incl. 2 slats and hardware, 38 deck CONNECTOR KIT - incl. 2 slats and hardware, 45 deck CONNECTOR KIT - incl. 2 slats and hardware, 56 deck REF MOTOR - draper drive, see Hydraulics page 4 & KEY woodruff SUPPORT - deflector, 38 deck, L/H SUPPORT deflector, 38 deck, R/H SUPPORT deflector, 45 deck, L/H SUPPORT deflector, 45 deck, R/H SUPPORT deflector, 56 deck, L/H & R/H DEFLECTOR plastic, 38 deck, L/H DEFLECTOR plastic, 38 deck, R/H DEFLECTOR plastic, 45 deck, L/H DEFLECTOR plastic, 45 deck, R/H DEFLECTOR plastic, 56 deck, L/H & R/H... 2

16 14 FEED DRAPER & DECK

17 FEED DRAPER & DECK 15 REF PART DESCRIPTION QTY SERIAL SUPPORT 38 deck SUPPORT 45 deck SUPPORT 56 deck SHIM pan, 38 deck, 972/973/974 headers SHIM pan, 45 deck, 972/973/974 headers SHIM pan, 56 deck, 972/973/974 headers PAN feed pan to cutterbar, 38 deck (shown), 972/973/974 headers PAN feed pan to cutterbar, 45 deck, 972/973/974 headers PAN feed pan to cutterbar, 56 deck, 972/973/974 headers DEFLECTOR steel, 38 deck, 972/973/974 headers DEFLECTOR steel, 45 deck, 972/973/974 headers DEFLECTOR steel, 56 deck, 972/973/974 headers COVER feed pan, 38 deck COVER feed pan, 45 & 56 decks SUPPORT drive roller, left WASHER flat SUPPORT - right, 963 Header RETAINER Header SUPPORT - left, 963 Header REF MOUNT Header, not serviced, order items 39 & PLATE transition, 963 Header, 38 deck PLATE transition, 963 Header, 45 deck PLATE transition, 963 Header, 56 deck ANCHOR transition plate support, 963 Header (welded to cutterbar) A NUT - hex, 5/8 NC B NUT - lock, smooth flange, 1/2 NC distorted thread C BOLT - round head, short square neck, 1/2 NC x 1-1/4 inch D BOLT - round head, square neck, 3/8 NC x 1 inch E NUT - lock, smooth flange, 3/8 NC distorted thread F SCREW machine, torx socket head, 3/8 NC x 3/4 inch G SCREW machine, torx socket head, 3/8 NC x 1/2 inch H WASHER lock, 1/2 inch K SETSCREW socket head, cone point, 3/8 NC x 5/16 inch L SCREW - machine, countersunk torx head, 3/8 NC x 3/4 inch M WASHER lock, 3/8 ID N NUT - hex, 1/2 NC P BOLT flange head, 1/2 NC x 1 inch Q WASHER flat, 17/32 inch ID R WASHER lock, 5/8 inch ID S BOLT hex head, 1/2 NC x 2-1/4 inch, thread full length T BOLT round head, square neck, 1/2 NC x 1-1/4 inch U BOLT round head, square neck, 1/2 NC x 1 inch V BOLT round head, short square neck, 3/8 NC x 3/4 inch W WASHER flat, 21/32 inch ID

18 16 RETRACTING TINE DRUM

19 RETRACTING TINE DRUM 17 REF PART DESCRIPTION QTY SERIAL DRUM retracting tine BEARING ball FLANGE motor mount with bearing, item SHAFT left SHAFT right WASHER flat BLOCK tine shaft SHAFT tine BEARING plastic, tine mount BEARING ball, with lock collar FLANGE bearing FLANGE bearing, with lube fitting TINE finger see note PIN roll, 1/8 x 1 inch PIN hair GUIDE plastic T-NUT 1/4 NC SCREW hex socket, button head, 1/4 NC x 3/4 inch COVER drum SUPPORT right PLATE cam SUPPORT left REF MOTOR drum drive, see Hydraulics pages 4 & COVER guide, used at outboard locations where tine is removed... AR DEFLECTOR plastic, front L/H and R/H, 38 & 45 decks DEFLECTOR plastic, front L/H and R/H, 56 deck DEFLECTOR plastic, L/H rear (38 deck) (was ) DEFLECTOR plastic, R/H rear (38 deck) (was ) DEFLECTOR plastic, L/H rear (45 deck) (was ) DEFLECTOR plastic, R/H rear (45 deck) (was ) DEFLECTOR plastic, L/H rear (56 deck) (was ) DEFLECTOR plastic, R/H rear (56 deck) (was ) KIT repair, RTD patch... AR SHIM... AR A BOLT hex head, 3/8 NC x 2-1/2 B NUT lock, smth flng, 3/8 NC dist thd C BOLT hex head, 1/2 NC x 2-1/2 inch D NUT lock, smth flng, 1/2 NC dist thd E BOLT rnd head, sq nk, ½ NC x 1 ½ F NUT jam, 1/2 NC G BOLT flange head, 1/2 NC x 1 inch H BOLT rnd head, sq nk, ½ NC x 1 ¼ J BOLT rnd hd, sq nk, 1/2 NC x 1 inch K NUT reg hex, 1/2 NC L BOLT rnd head, sq nk, 3/8 NC x 3/4 M BOLT hex hd, 1/2 NC x 2 inch P BOLT hex hd flange, 1/2 NC x 3/4 R WASHER lock, 3/8 ID S SCREW machine, torx head, 3/8 NC x ¾ NOTES: 1. Tine quantities shown are for full drum width. For some combines, tines are removed from each end of the drum to ensure clearance to header side drapers.

20 18 CASE 20 SERIES COMBINES ADAPTER COMPLETION PARTS

21 CASE 20 SERIES COMBINES ADAPTER COMPLETION PARTS 19 REF PART DESCRIPTION QTY SERIAL MEMBER - adapter frame, right MEMBER - adapter frame, left PIN straight PIN clamp SUPPORT R/H shield, top SHIELD R/H, rear section SUPPORT R/H shield, bottom SHIELD R/H, front section SHIELD R/H extension for narrow feeder house Models 1640, 1644, 1660, 2166, ARM drive support PIN lynch ARM drive (was ) ARM - drive PLATE walkway REF FRAME adapter, not serviceable, see Frame and Float pages 2 & B4819 Case 2300 Series Sliding Pin Latch Kit Available through Wholegoods only BRACKET L/H, sliding latch kit BRACKET R/H, sliding latch kit... 1 A BOLT - round head, square neck, 1/2 NC x 1 inch B NUT - lock, smooth flange, 1/2 NC distorted thread C BOLT - flange head, 1/2 NC x 1 inch D BOLT round head, square neck, 5/8 NC x 1 inch F NUT - hex jam, 5/8 NC G BOLT hex head, 5/8 NC x 4-1/2 inch K BOLT - flange head, 3/8 NC x 3/4 inch L NUT - lock, smooth flange, 3/8 NC distorted thread M WASHER - flat, 13/32 inch ID N BOLT flange head, 3/8 NC x 1-1/4 inch P SCREW self tapping, 3/8 NC x 5/8 inch Q NUT lock, smooth flange, 5/8 NC distorted thread R BOLT hex head, M x 25mm S WASHER lock, 12.5mm ID T BOLT round head square neck, 5/8 NC x 1-1/2 inch

22 20 CASE 20 SERIES COMBINES HEADER COMPLETION PARTS

23 CASE 20 SERIES COMBINES HEADER COMPLETION PARTS 21 REF PART DESCRIPTION QTY SERIAL BRACKET hydraulic coupler mount FASTENER cable tie, red FASTENER cable tie, green FITTING male hydraulic coupler FITTING female hydraulic coupler HOSE hydraulic FITTING hydraulic coupler FASTENER cable tie, white FASTENER cable tie, yellow HOSE hydraulic FITTING hydraulic, connector HOLDER - hose HOLDER hose FASTENER cable tie, black HARNESS wiring CLAMP - wiring REF HOSE hydraulic, reel drive, pressure REF HOSE hydraulic, fore-aft, aft REF HOSE hydraulic, reel drive, return REF HOSE hydraulic, fore-aft, fore REF HOSE hydraulic, reel lift FASTENER cable tie GUSSET coupler bracket (was ) PLUG dust, female coupler (red) CAP dust, male coupler (black) PLUG dust, male coupler (red)... 1 A BOLT round head, square neck, 1/2 NC x 1 inch B NUT lock, smooth flange, 1/2 NC distorted thread C BOLT round head, square neck, 3/8 NC x 1 inch D BOLT round head, square neck, 3/8 NC x 1-1/4 inch E NUT lock, smooth flange, 3/8 NC F SCREW self tapping, 3/8 NC x 5/8 inch G BOLT hex head, 1/2 NC x 2 inch, threaded full length H NUT hex jam, 1/2 NC

24 22 CASE AFX/NEW HOLLAND CR/CX COMBINES ADAPTER/COMBINE COMPLETION PARTS

25 CASE AFX/NEW HOLLAND CR/CX COMBINES ADAPTER/COMBINE COMPLETION PARTS 23 REF PART DESCRIPTION QTY SERIAL ADAPTER - plate PIN lynch, New Holland CR/CX PIN lynch, Case AFX HANDLE drive gear, New Holland CR/CX HANDLE drive gear, Case AFX SHIM latch LATCH - adapter REF FRAME adapter, not serviceable, see Frame and Float pages 2 & ARM gear drive mount, New Holland CR combine 38 and 45 decks ARM gear drive mount, New Holland CX 56 deck SHIM REF INDICATOR header angle, see NOTE 1 below LATCH SPRING torsion PIN clevis RING split CLAMP torque arm, New Holland CX 56 deck... 1 A BOLT round head, square neck, 5/8 NC x 1 inch B NUT hex jam, 5/8 NC distorted thread C NUT lock, smooth flange, 3/8 NC distorted thread D NUT lock, smooth flange, 5/8 NC distorted thread G BOLT round head, square neck, 1/2 NC x 1-1/2 inch H NUT lock, 3/4 NC distorted thread J BOLT hex head, 3/4 NC x 2 inch L BOLT round head, square neck, 3/8 NC x 1-1/4 inch M BOLT hex head, M12 x 25mm N WASHER lock, 12.5mm ID P NUT lock, smooth flange, 1/2 NC distorted thread R WASHER flat, 21/32 inch ID S BOLT round head, square neck, 1/2 NC x 1 inch NOTES: 1. See page 3 for part number. Repair part will have cut-out at top mounting hole. Remove this cut-out to enlarge hole for Case AFX/New Holland CR & CX.

26 24 CASE AFX/NEW HOLLAND CR/CX COMBINES HEADER COMPLETION PARTS

27 CASE AFX/NEW HOLLAND CR/CX COMBINES HEADER COMPLETION PARTS 25 REF PART DESCRIPTION QTY SERIAL VALVE multi-link, includes items 16 & COUPLING ¼, for multi link valve COUPLING 3/8, for multi link valve FASTENER cable tie, green, to fore-aft, fore FASTENER cable tie, red, to fore-aft, aft FASTENER cable tie, white, to reel drive pressure FASTENER cable tie, black, to reel lift FASTENER cable tie, yellow, to reel drive return FITTING hydraulic, orifice FITTING hydraulic HARNESS wiring A CAP for multi pin connector on harness RESISTOR header recognition CLAMP wiring harness BRACKET hydraulic coupler mount PLATE extension, for European shielding, used to mount item HARNESS wiring, header recognition, for units without float optimizer... A/R GUSSET coupler bracket (was ) KIT multi-link valve cover... A/R KIT multi-link latch button & hardware (does not include lever)... A/R A BOLT round head, square neck, 1/2 NC x 1 inch B NUT lock, smooth flange, 1/2 NC distorted thread C BOLT hex head, 5/16 NC x 1 inch D NUT lock, smooth flange, 5/16 NC distorted thread E SCREW self tapping, 3/8 NC x 5/8 inch F NUT lock, smooth flange, 3/8 NC distorted thread (for item 13) G BOLT round head, square neck, 3/8 NC x 3/4 inch (for item 13) H BOLT hex head, 1/2 NC x 2 inch, threaded full length J NUT hex jam, 1/2 NC

28 26 JOHN DEERE COMBINES ADAPTER COMPLETION PARTS

29 JOHN DEERE COMBINES ADAPTER COMPLETION PARTS 27 REF PART DESCRIPTION QTY SERIAL MEMBER adapter frame, L/H MEMBER adapter frame, R/H (was ) ANCHOR drive, 9600, 9610, 9650 & contour master combines (was ) ARM torque, (was ) HANDLE drive gear HANDLE drive gear (except 60 Series) HANDLE drive gear, 60 Series only CLAMP hex bore SHAFT - spline SHIELD LATCH rubber SHIELD - rubber SHIELD - left REF FRAME adapter, not serviceable, see Frame and Float pages 2 & PIN lynch ARM torque, prior to 50 Series, after SN use item SHIELD BEAM upper support, 60 Series ARM torque, 60 Series WASHER spacer (position as required to space torque arm) SUPPORT upper A BOLT hex head, 3/4 NC x 2 inch B WASHER flat, 19.8 mm ID C WASHER lock, 19 mm ID D BOLT round head, square neck, 5/8 NC x 1-1/4 inch E BOLT round head, square neck, 1/2 NC x 1 inch F NUT lock, smooth flange, 1/2 NC distorted thread G NUT lock, smooth flange, 5/8 NC distorted thread H WASHER flat, 20.6 mm ID J BOLT round head, square neck, 1/2 NC x 1-1/4 inch K BOLT hex head, 5/8 NC x 1-1/2 inch L BOLT hex head, 1/2 NC x 4-1/2 inch M BOLT hex head, 1/2 NC x 3 inch N BOLT round head, square neck, 3/8 NC x 3/4 inch P NUT lock, smooth flange, 3/8 NC distorted thread Q BOLT hex head, 3/8 NC x 1-1/2 inch R BOLT round head, square neck, 3/8 NC x 1 inch S BOLT hex head, M x 25mm T WASHER lock, 12.5mm ID U BOLT hex head, 5/8 NC x 1-3/4 inch

30 28 JOHN DEERE COMBINES (Pre 50 Series & 50 Series Models) HEADER COMPLETION PARTS

31 JOHN DEERE COMBINES (Pre 50 Series & 50 Series Models) HEADER COMPLETION PARTS 29 REF PART DESCRIPTION QTY SERIAL BRACKET hydraulic coupler mounting FASTENER cable tie, red FASTENER cable tie, green FITTING female hydraulic coupler c/w lever HOSE hydraulic FITTING connector SPACER coupler FASTENER cable tie, white FASTENER cable tie, yellow HOSE END reusable (for 2 arm reel drive only) FITTING male hydraulic coupler FITTING female hydraulic coupler FITTING connector HOLDER hose HOLDER hose FASTENER cable tie, black FITTING hydraulic coupler HARNESS wiring, JD pre-50 series combines only A HARNESS wiring, JD 50 Series and up combines B CAP for multi pin connector on harness CLAMP wiring, JD pre-50 Series combines only REF HOSE hydraulic, reel fore-aft, fore REF HOSE hydraulic, reel lift REF HOSE hydraulic, reel drive, pressure REF HOSE hydraulic, reel drive, return GUSSET coupler bracket, inboard header legs (was ) B 2544 * MOUNTING KIT JD Reel Speed Sensor for 963 Headers...OPT SPROCKET timing, 50 tooth SUPPORT sensor WASHER flat (third washer comes with header) HARNESS wiring, extension (for 21 & /973/974 & all 963 headers) B 4001 * MOUNTING KIT JD Reel Speed Sensor for 972/973/974 Headers...OPT SPROCKET timing, 31 tooth SUPPORT sensor HOLDER - harness... 2 A BOLT round head, square neck, 1/2 NC x 1 inch B NUT lock, smooth flange, 1/2 NC distorted thread C BOLT round head, square neck, 3/8 NC x 1 inch D BOLT round head, square neck, 3/8 NC x 1-1/4 inch E NUT lock, smooth flange, 3/8 NC F SCREW self tapping, 3/8 NC x 5/8 inch G BOLT hex head, 1/2 NC x 2 inch, threaded full length H NUT hex jam, 1/2 NC J BOLT flange head, 3/8 NC x 3/4 inch * - Available through WholeGoods only.

32 30 JOHN DEERE COMBINES (60 Series) HEADER COMPLETION PARTS

33 JOHN DEERE COMBINES (60 Series) HEADER COMPLETION PARTS 31 REF PART DESCRIPTION QTY SERIAL BRACKET hydraulic coupler mounting LATCH coupler bracket PLUG - rubber PAD - rubber FASTENER cable tie, red FASTENER cable tie, orange FASTENER cable tie, green HOSE - hydraulic FASTENER cable tie, white FASTENER cable tie, yellow HOSE - hydraulic HOSE - hydraulic BRACKET mounting HOLDER hose FASTENER cable tie, black (7-3/4 inches long) HARNESS electrical wiring RING retaining, inverted FASTENER cable tie, black (14 inches long) GUSSET coupler bracket (was ) REF LEG L/H inner header leg FITTING hydraulic, swivel adapter (headers with hydraulic center link) COUPLING-MULTI SEAL KIT 3/8 in SEAL KIT ½ in A BOLT round head, square neck, 1/2 NC x 1 inch B NUT lock, smooth flange, 1/2 NC distorted thread C BOLT hex washer head, shoulder, 3/8 NC x 23 mm long D NUT lock, smooth flange, 3/8 NC E SCREW hex washer head, thread forming, 3/8 NC x 5/8 inch F BOLT hex head, 3/8 NC x 2-1/4 inch G BOLT hex head, 1/2 NC x 2 inch, threaded full length H NUT hex jam, 1/2 NC

34 32 LEXION COMBINE ADAPTER COMPLETION PARTS

35 LEXION COMBINE ADAPTER COMPLETION PARTS 33 REF PART DESCRIPTION QTY SERIAL 1 REF FRAME adapter, not serviceable, see Frame and Float pages 2 & HOLDER pump storage LATCH - top PIN roll ARM - lever LEVER - latch LEVER - latch NSS SHAFT - latch PIN bottom latching ARM HANDLE drive gear PIN lynch ARM support, wide feeder house models (was ) ARM support, narrow feeder house models (was ) HANDLE gear drive ARM gear drive support, for HP5 Tilting Feed Elevator only SUPPORT plate, for HP5 Tilting Feed Elevator only... 1 (item 17 qty = 2 for wide feeder house models) ARM gear drive support, offset, for standard wide feeder house ARM gear drive support, flat, for standard narrow feeder house PLATE backing... 1 A BOLT round head, square neck, 3/8 NC x 1-1/4 inch B NUT lock, smooth flange, 3/8 NC distorted thread C NUT lock, smooth flange, 1/2 NC distorted thread D NUT hex head, 3/4 NC, distorted thread E NUT hex jam, 3/4 NC F BOLT hex head, 1/2 NC x 2-1/4 inch G WASHER flat, SAE 0.66 inch ID H BOLT hex head, 1/2 NC x 1-1/2 inch J BOLT hex head, M x 25 mm K WASHER lock, 12.5 mm ID L BOLT flange head, M10 x 35 mm M BOLT hex head, M10 x 45 mm N BOLT hex head, 1/2 NC x 2 inch P NUT lock, 1/2 NC distorted thread

36 34 LEXION COMBINE HEADER COMPLETION PARTS

37 LEXION COMBINE HEADER COMPLETION PARTS 35 REF PART DESCRIPTION QTY SERIAL 400 SERIES COMBINE COMPLETION BRACKET hydraulic coupler mounting FITTING female hydraulic coupler FITTING male hydraulic coupler FITTING hydraulic adapter FASTENER cable tie, white REF HOSE hydraulic, reel drive FASTENER cable tie, yellow REF HOSE hydraulic, reel drive HOLDER hose FITTING hydraulic, 90º elbow VALVE hydraulic, 2 function FASTENER cable tie, red REF HOSE hydraulic, from P2 on selector valve, red tie REF HOSE hydraulic, from P1 on selector valve, green tie REF HOSE hydraulic, reel lift FITTING hydraulic, restrictor (0.052 orifice) FITTING hydraulic, adapter FITTING hydraulic, connector, 3/8 tube x 1/4 NPT (30º seat) HOSE hydraulic, with o-rings O-RING for hose COUPLER hydraulic and electrical BRACKET hydraulic coupler GUARD rubber cap FITTING hydraulic, M12 thread into block (depends on item 11 thread size) FITTING hydraulic, M14 thread into block (depends on item 11 thread size) FASTENER cable tie, green FASTENER cable tie, black HARNESS wiring, 2 function HARNESS wiring connector (lights) GUSSET coupler bracket (was ) SPACER wiring harness SERIES COMBINE COMPLETION BRACKET hydraulic coupler mounting GUSSET coupler bracket FASTENER cable tie, red FASTENER cable tie, green FASTENER cable tie, white FASTENER cable tie, yellow COUPLER hydraulic and electrical (was ) VALVE hydraulic, 2 function VALVE hydraulic, 2 function VALVE hydraulic, 2 function COVER coupler HARNESS wiring HARNESS wiring FITTING hydraulic, adapter FITTING hydraulic, adapter, M12 thread into block (depends on item 36 thread size) FITTING hydraulic, adapter, M14 thread into block (depends on item 36 thread size) FITTING hydraulic, connector FITTING hydraulic, connector FITTING hydraulic, 90 elbow FITTING hydraulic, 45 elbow, c/w O-ring HOSE hydraulic HOSE hydraulic for hose (6 mm I.D.) O-RING O-RING for hose (8 mm I.D) FITTING hydraulic, 90º elbow REF HOSE hydraulic, from P2 on selector valve, red tie REF HOSE hydraulic, from P1 on selector valve, green tie REF HOSE hydraulic, reel lift REF HOSE hydraulic, reel drive, pressure REF HOSE hydraulic, reel drive, return FITTING union FITTING union SPACER wiring harness...1 Note: See next page for hardware.

38 36 LEXION COMBINE HEADER COMPLETION PARTS (Continued)

39 LEXION COMBINE HEADER COMPLETION PARTS (Continued) 37 REF PART DESCRIPTION QTY SERIAL A BOLT round head, sq neck, 1/2 NC x 1 B NUT - lock, smooth flange, 1/2 NC, D.T. C BOLT hex head, 5/16 x 1 inch D NUT flange head, 5/16 NC E NUT flange head, 3/8 NC F BOLT round head, sq neck, 3/8 NC x 3/4 G BOLT hex head, M5 x 45mm H BOLT hex head, 5/16 NC x 3-3/4 J BOLT round head, sq neck, 3/8 x 1-1/2, T.F.L K BOLT hex head, 1/2 NC x 2, T.F.L. L NUT hex jam, 1/2 NC

40 38 LEXION COMBINE AUTO REEL SPEED/HEIGHT GROUP

41 LEXION COMBINE AUTO REEL SPEED/HEIGHT GROUP 39 REF PART DESCRIPTION QTY SERIAL 400 Series Lexion Combines: DISC 13 teeth, reel speed sensor WASHER flat SUPPORT reel speed sensor SENSOR reel speed NUT reel sensor ARM reel height sensor, 3 arm headers ROD link, reel height sensor, 3 arm headers POTENTIOMETER ASSEMBLY HARNESS reel speed/height HARNESS extension, 2 arm headers HARNESS wiring, 2 or 3 arm headers SUPPORT reel height sensor, 2 arm headers DISC 8 teeth, reel speed sensor SUPPORT reel speed sensor CLAMP harness Series Lexion Combines: SENSOR reel height SUPPORT sensor, 963, 973, 974 headers only ARM sensor, 963, 973, 974 headers only SUPPORT 973 & arm headers only SUPPORT headers only ROD linkage, headers only ROD linkage, 973, , 36 & 39 headers only HARNESS wiring BRACKET speed sensor, 973 & 974 Headers only BRACKET speed sensor, 963 Headers only DISC 8 teeth, reel speed sensor, 973 & 974 Headers only DISC 12 teeth, reel speed sensor, 963 Headers only SENSOR reel speed WASHER flat... 2 A BOLT hex head, 1/4 NC x 1-1/4 B WASHER lock, 1/4 NC C BOLT rnd hd, sq nk, 5/16 NC x 1 inch D NUT lock, serrated flange, 5/16 NC E NUT hex, 3/8 NC F BOLT hex head, 5/16 NC x 1-3/4 inch G BOLT hex head, 1/4 NC x 1 inch H NUT lock, 1/4 NC distorted thread J WASHER flat, 9/32 inch ID K SCREW self tapping, 3/8 NC x 5/8 inch L BOLT flange head, 3/8 NC x 3/4 inch M SCREW self tapping, 1/4 NC x ½ N BOLT rnd hd, sq nk, #10-24 NC x ¾ P NUT lock, #10-24 NC Q SCREW machine, M6x8 R NUT lock, 1/4 NC S BOLT hex head, 5/8 NC x 4 inch T WASHER flat, 5/8 ID U NUT lock, 5/8 NC V BOLT rnd hd, sq nk, 1/4 NC x 3/4 inch W NUT serrated flange, 1/4 NC

42 40 AGCO COMBINES ADAPTER COMPLETION PARTS

43 AGCO COMBINES ADAPTER COMPLETION PARTS 41 REF PART DESCRIPTION QTY SERIAL BEAM - upper MEMBER L/H MEMBER R/H BEAM lower (was ) PIN lynch, qty = 2 with variable speed feeder house ANCHOR (was ) ARM standard feeder house (was ) HANDLE gear drive (was ) SHIELD SHIELD LATCH rubber SHIELD rubber SHIELD REF FRAME adapter, not serviceable, see Frame and Float pages 2 & ARM pump support, variable speed feeder house only PIN clevis, 5/8 dia. x 0.98 effective length, variable speed feeder house only... 1 A BOLT round head, square neck, 5/8 NC x 2-1/2 inch B BOLT round head, square neck, 5/8 NC x 1-1/4 inch C BOLT round head, square neck, 1/2 NC x 1 inch D NUT lock, smooth flange, 1/2 NC distorted thread E BOLT hex head, serrated flange, 1/2 NC x 1 inch F NUT smooth flange, 5/8 NC distorted thread G BOLT round head, square neck, 1/2 NC x 1-1/4 inch H BOLT hex head, 5/8 NC x 1-1/2 inch J BOLT hex head, M12 x 1-3/4 x 25 long K WASHER spring lock P BOLT round head, square neck, 3/8 NC x 3/4 inch Q NUT smooth flange, 3/8 NC distorted thread R BOLT hex head, 3/8 NC x 1-1/2 inch S BOLT round head, square neck, 3/8 NC x 1 inch

44 42 AGCO COMBINES HEADER COMPLETION PARTS

45 AGCO COMBINES HEADER COMPLETION PARTS 43 REF PART DESCRIPTION QTY SERIAL BRACKET - mounting FASTENER cable tie, white FASTENER cable tie, yellow HOLDER couplers HOLDER hose & harness FITTING hydraulic, female coupler FITTING hydraulic, tee FITTING hydraulic, tee VALVE check FITTING hydraulic, male coupler HOSE hydraulic FITTING hydraulic, male coupler CAP dust, rubber FITTING hydraulic, connector, 3/8 tube x 1/4 NPT (30º seat) FASTENER cable tie, black HARNESS wiring REF HOSE hydraulic, reel drive, return REF HOSE hydraulic, reel drive, pressure GUSSET coupler bracket (was ) REF HOSE hydraulic, reel lift SPACER coupler... 1 A BOLT round head, square neck, 1/2 NC x 1 inch B NUT lock, smooth flange, 1/2 NC distorted thread C BOLT round head, square neck, 38 NC x 1 inch D BOLT round head, square neck, 3/8 NC x 1-1/4 inch E NUT lock, smooth flange, 3/8 NC distorted thread F BOLT hex head, 1/2 NC x 2 inch, threaded full length G NUT hex jam, 1/2 NC

46 44 DECALS 1A A A

47 DECALS 45 REF PART DESCRIPTION QTY SERIAL DECAL Header Hazard (non-verbal) 1A DECAL Header Hazard (text version) DECAL DANGER - INNER: Shield Missing DECAL DANGER - OUTER: Rotating Driveline BOOKLET - driveline DECAL - Hydraulic Oil (non-verbal) 4A DECAL Hydraulic Oil (text version) DECAL Float Lock Out (non-verbal) 5A DECAL Float Lock Out (text version) DECAL model DECAL IMPORTANT: Pan to Cutterbar Clearance DECAL Float Settings

48 46 DRIVELINE

49 DRIVELINE 47 REF PART DESCRIPTION QTY SERIAL * T DRIVELINE complete... 1 ** T DRIVELINE complete... 1 *** HEX BORE DRIVELINE complete YOKE 6T driveline YOKE 21T driveline YOKE hex bore driveline CROSS JOURNAL ASSEMBLY includes c-clips and grease fitting FITTING grease, M8 x straight YOKE 1-3/8 inch bore CHAIN anti-rotation HALF SHAFT 6T driveline, outer, c/w shield HALF SHAFT 21T driveline, outer, c/w shield HALF SHAFT Hex Bore driveline, outer, c/w shield HALF SHAFT inner, c/w shield SHIELD outer 21T & hex bore drivelines SHIELD outer - 6T driveline SHIELD inner BOLT hex head, M x 75 mm long NUT hex, M WASHER lock, M FITTING - lube... 1 * Driveline 6T New Holland CR/CX and Case AFX Combines ** Driveline 21T John Deere, Agco & Lexion Combines *** Driveline Hex Bore Case 20 Series Combines

50 48 FLOAT OPTIMIZER (Attachment) Case, Agco & John Deere (50 & 60 Series) Combines SN and below CASE 2300 SERIES COMBINES

51 FLOAT OPTIMIZER (Attachment) Case, Agco & John Deere (50 & 60 Series) Combines SN and below 49 REF PART DESCRIPTION QTY. SERIAL SUPPORT lower mounting bracket, John Deere 50 Series SUPPORT lwr mntg brkt, Case Axial Flow/2300 Combines ARM sensing, top link PLATE potentiometer mntg, JD 50 Series & Case Axial Flow PLATE potentiometer mounting, Case 2300 Series CLIP rod end ROD linkage, John Deere 50 Series ROD linkage, Case Axial Flow Combines ROD linkage, Case 2300 Series Combines WASHER flat, SAE 9/32 ID ARM pivot, John Deere 50 Series ARM pivot, Case Axial Flow Combines ARM pivot, Case 2300 Series Combines SPRING torsion 1 9 REF CONTROL potentiometer, order John Deere RE CONTROL potentiometer, Case Axial Flow Combines ARM upper, John Deere 50 Series & Case 2300 Series ARM upper, Case Axial Flow Combines INDICATOR rod, header float SUPPORT indicator pivot INDICATOR gauge, header float HARNESS wiring, John Deere 50 Series HARNESS wiring, Case Axial Flow Combines HARNESS wiring, Case 2300 Series Combines HOLDER harness WASHER - special 1 A BOLT hex head, 3/8 NC x 2 ½ inch B NUT lock, smooth flange, 3/8 NC distorted thread C SCREW self-tapping, 3/8 x 5/8 inch D BOLT hex head, 3/8 NC x ¾ inch G BOLT round head, square neck, #10 NC x 1 ½ inch H NUT lock, NC nylon patch J BOLT round head, short square neck, 3/8 NC x ¾ inch K BOLT large flange head, 3/8 NC x 1 inch (at optimizer end) BOLT round hd, short square neck, 3/8 NC x ¾ inch (at left leg) L BOLT hex head, ¼ NC x 1 inch M NUT lock, ¼ NC distorted thread

52 FLOAT OPTIMIZER (Attachment) Case, Agco & John Deere (50 & 60 Series) Combines SN and above 51 REF PART B4415 B4499 DESCRIPTION QTY. SERIAL FLOAT OPTIMIZER KIT Case 2100/2300 and AFX Combines FLOAT OPTIMIZER KIT John Deere (50 & 60 Series) & Agco SUPPORT lower mounting bracket PLATE sensor mounting ARM upper SPRING torsion INDICATOR gauge, header float INDICATOR rod, header float SENSOR - potentiometer ARM pivot SUPPORT pivot arm ROD linkage CLIP rod end ARM sensing HOLDER - harness HARNESS float optimizer, Case 2100/2300 Series (was ) HARNESS float optimizer, Case AFX Combine HARNESS float optimizer, John Deere (50 Series) HARNESS float optimizer, John Deere (60 Series) HARNESS float optimizer, Gleaner R62/R HARNESS float optimizer, Gleaner R65/R75, Challenger 660/670, Massey Ferguson 9690/ A SCREW hex washer head, #10 x 1-1/2 inch, self-tapping B BOLT hex head, 3/8 NC x 2-1/2 inch C NUT lock, smooth flange, 3/8 NC distorted thread D SCREW self-tapping, 3/8 x 5/8 inch E WASHER flat, 13/32 inch ID F BOLT round head, square neck, 3/8 NC x 2-1/4 inch, thread full G WASHER flat, 17/32 inch ID H NUT serrated flange lock, 3/8 NC J BOLT hex head, 3/8 NC x 3/4 inch K BOLT large flange head, 3/8 NC x 1 inch BOLT round head, short square neck, 3/8 NC x 3/4 inch

53 50 FLOAT OPTIMIZER (Attachment) Case, Agco & John Deere (50 & 60 Series) Combines SN and above 872 Mounting Hardware 873 Mounting Hardware

54 52 FLOAT OPTIMIZER (Attachment) New Holland CR / CX Combines (SN and below

55 FLOAT OPTIMIZER (Attachment) New Holland CR / CX Combines SN and below 53 REF PART B4325 DESCRIPTION QTY. SERIAL FLOAT OPTIMIZER KIT New Holland CR/CX Combines SUPPORT lower mounting bracket ARM sensing, top link CLIP rod end CONTROL potentiometer ARM pivot WASHER flat, SAE 9/32 ID SPRING torsion ROD linkage ARM upper INDICATOR rod, header float SUPPORT indicator pivot INDICATOR gauge, header float HARNESS wiring, New Holland CR/CX HOLDER harness... 5 A BOLT hex head, 3/8 NC x 2 ½ inch B NUT lock, smooth flange, 3/8 NC distorted thread C SCREW self-tapping, 3/8 x 5/8 inch E BOLT hex head, ¼ NC x 1 inch F NUT lock, ¼ NC distorted thread G BOLT round head, square neck, #10 NC x ½ inch H NUT lock, NC nylon patch J BOLT round head, short square neck, 3/8 NC x ¾ inch K BOLT large flange head, 3/8 NC x 1 inch (at optimizer end) BOLT round hd, short square neck, 3/8 NC x ¾ inch (at left leg) L BOLT flange head, 3/8 NC x ¾ inch M NUT serrated flange lock, 3/8 NC N BOLT round head, square neck, ¼ NC x ½ inch P NUT serrated flange lock, ¼ NC