Maintenance and Adjustment Guide

Size: px
Start display at page:

Download "Maintenance and Adjustment Guide"

Transcription

1 c and Maintenance and Adjustment Guide D-Series Carton Clamps This sheet describes the recommended adjustments and periodic maintenance for D-Series Carton Clamps. Following these guidelines will help reduce service downtime and extend the operation life of the attachment. Daily Schedule CL4327.ai CL4324.ai 1 Check for oil leaks at the cylinder rod seals and at all fittings. 3 Check the contact pads for nicks, sharp edges, worn rubber, major dents or deformities. Maximum allowable wear on front corner = 1 in. (25 mm). Maximum rubber surface variance =.125 in. (3 mm) CL4384.eps 2 Check the cylinder rod end nuts for properly installed keepers and cotter pins. cascadew corporation For Technical Support... To Order Parts... Call: Fax: Call: Fax: Internet: Internet: Write: Cascade Corporation, PO Box 20187, Portland, OR Write: Cascade Corporation, 2501 Sheridan Ave., Springfield, OH 45505

2 400 Hour Schedule Neutral Camber Negative Camber Bolt-On Hooks Top Hooks CL4387.eps Quick Change Hooks CL4329.ai Neutral Camber 1 Check the upper and lower mounting hooks for proper installation. Tighten the lower mounting hooks to a torque of ft.-lbs. ( Nm). Negative Camber 3 Check the contact pads for camber alignment. Camber should be negative.25 in. (6 40 in. (101.6 cm) opening and.50 in. (13 50 in. (127.0 cm) opening. CL4389.eps CL4388.eps 2 Check for bent or bowed contact pads in both the vertical and horizontal orientations. Maximum allowable pad deformity =.25 in. (6 mm) CL4331.ai 2 4 Check clamp force pressure settings. Align indicator front to back on arm pivot points. Top to bottom alignment should be parallel and even with clamp cylinders.

3 CL4334.ai CL4390.eps 8 Lubricate the arm bars with chassis grease. 5 Check wear tiles on bottom of stabilizers, quantity and location varies. Replace when tile is less than.125 in. (3 mm) thick. Stabilizer CL4391.eps CL4384.eps 9 Check the stabilizers for straightness. Replace if visibly bent. 6 Inspect and lubricate the cylinder anchor nuts. Tighten the nuts to a torque of ft.-lbs. ( Nm). Apply wheel bearing grease to the spherical portion of the anchor nut. CL4337.ai 7 Check the arm bearings for wear. Shim or replace if gap between the arm and bearing exceeds.15 in. (4 mm). See 2000 Hour Schedule Step 2. 3

4 400 Hour Schedule (Continued) 2000 Hour Schedule D Bearing Surface B Arm Lug C Stabilizer 10 Check the contact pad pivots for wear. CL4392.eps A CL4394.eps Position contact pads.50 in. (12 mm) above the floor.50 in. (12 mm) CL4338.ai 11 Tighten the frame/mounting plate capscrews to a torque of ft.-lbs. (81 88 Nm). 1 Perform all 400 Hour Schedule checks. 2 Replace arm bearings, if required, using the following procedures: NOTE: The attachment can remain mounted on the truck. A Extend the arms. Lower the attachment to position the contact pads.50 in. (12 mm) above the floor. Remove the cotter pin, locking cap and nut retaining the cylinder rod to the arm lug. B Attach a suitable overhead hoist and chain to the arm. The chain must be kept away from the arm bearing surface. WARNING: Check the attachment weight (located on the nameplate) to make sure the overhead hoist and chains or straps are at least the rated capacity of the attachment. C Retract the cylinder rods until they come out of engagement with the arm lugs. WARNING: Keep feet and fingers out from under the contact pads and arms. D Pull the arm assembly out of the frame. 4

5 E Remove the bearing spacer located between the upper and lower bearing in each arm carrier slot. F Pry the bearings out of the frame with a screwdriver and slide outward. CAUTION: Do not gouge aluminum frame surfaces. NOTE: To ease removal of the first bearing from the frame, push the innermost boss out of its hole. Frame F Boss Slide Outward Inner most boss push here Frame E CL4340.ai F CL4341.ai Slide Outward G Use dial calipers to measure dimension d1 of both ends of arm bar opening in upper and lower aluminum frames. H Place an upper and lower bearing strip on each arm bar. Measure dimension d2. I Determine the shim thickness required to leave.015 in. (.4 mm) clearance between each set of bushing strips and each arm bar opening. Use the following formula: [d1.015 in.] d2 = shim thickness required Example: d1 = in. d2 = in. [2.165 in..015 in.] in. =.065 in. 1 Pink Shim =.015 in. 1 Yellow Shim =.020 in. Use 3 yellow shims =.60 in. J Decrease the width of the bearing spacer to the dimension shown to provide room to install the bearings. K Tape the required shims for each arm bar opening to the lower bearing strip only. Install the bearing strips and bearing spacers. L After reinstalling the arms in the frames, check for excess tightness of the arm bars while sliding in the frames. G d1 Aluminum Frame Bearing Strips Upper Bearing Strip CL4342.ai Arm Bar d2 H Bearing Spacer.08 in. (2.03 mm) Lower Bearing Strip CL4343.ai K J Shim Lower Bearing Strip Decrease Bearing Spacer Width 5

6 2000 Hour Schedule (continued) M For reassembly, reverse the above procedures, except for the following special instructions for cylinder anchor nuts. Lubricate the cylinder rod threads, nut threads and spherical portion of the nut with STP. Install the washer on the rod end with the beveled side facing the lug. Engage the rod end into the lug. Tighten the rod end nut to a torque of ft.-lbs. ( Nm). Prevent the rod turning by using a wrench on the hex washer. NOTE: The rod end nut is being tightened against the hex washer. The nut will not be tight against the arm lug. This looseness allows for frame deflection during clamping. Install the locking cap and cotter pin. Lubricate the bearing portion of the arm bars with a thin film of chassis grease. M Tighten rod end nut to a torque of: ft.-lbs. ( Nm) (lubed). Beveled side facing lug CL4344.eps 3 Flush and replace the truck/clamp hydraulic system fluid. Use SAE 10W petroleum base oil per Military Specification MIL or MIL B. CL4345.ai 4 Check the truck hydraulic system pressure and flow rate. A Check the pressure delivered by the truck. Refer to the truck service manual. The pressure must be within 100 psi (7 bar) of specified truck pressure. TRUCK PRESSURE MUST NOT EXCEED 2300 PSI (160 bar), measured at the hose terminal. B Check the flow volume at the hose terminal. The flow should be 4 to 7 GPM (15-26 L/min). If the truck pressure and flow volume are correct, proceed with the pressure test. C Clamps with Solenoid Adaption Press the auxiliary valve control knob button. Listen for the click at the solenoid valve. If the solenoid valve does not click when the button is pushed, check the electrical wiring and solenoid coil. D Check for external leaks. Close the arms fully. Hold the clamp control handle in the clamp position for a few seconds. E Return the handle to neutral. Inspect all fittings, lines and the cylinders for leaks. If there are no leaks, proceed with the pressure test. CL4346.ai WARNING: Before removing any hoses, relieve pressure in the hydraulic system. Turn truck off, then open the truck auxiliary control valves several times in both directions. Hose Terminal 6

7 5 Test the attachment clamp circuit. A Install the pressure gauge and hose assembly in the valve test port marked G, located on the back of the valve body. B Start the truck. Fully close the arms. Hold the clamp control handle in the clamp position for a few seconds. C Return the handle to neutral. Watch the gauge pressure reading. If the gauge pressure does not drop more than 150 psi (10 bar) initially and an additional drop does not exceed 25 psi (2 bar) per minute, the problem is not hydraulic. If the gauge pressure drops more than 150 psi (10 bar) initially and an additional drop exceeds 25 psi (2 bar) pre minute, proceed with 2000 Hour Schedule Step 6 to isolate the faulty components. IMPORTANT: Before removing pressure gauge, momentarily actuate clamp open circuit. This will relieve pressure trapped by the check valve in the clamp circuit. WARNING: Before removing any hoses, relieve pressure in the hydraulic system. Turn truck off, then open the truck auxiliary control valves several times in both directions. Install gauge and hose in port G CL4347.ai 6 Test the attachment check valve circuit. WARNING: Before removing any hoses, relieve pressure in the hydraulic system. Turn truck off, then open the truck auxiliary control valves several times in both directions. A Remove the bumper. B Disconnect the hydraulic lines at the rod end of both cylinders. Cap the ports and plug the lines. C Start the truck. Hold the clamp control handle in the clamp position for a few seconds. D Return the handle to neutral. Watch the gauge pressure reading. If the gauge pressure drops more than 150 psi (10 bar) initially and an additional drop exceeds 25 psi (2 bar) per minute, the check valve is faulty and requires service. If the gauge pressure does not drop more than 150 psi (10 bar) initially and an additional drop does not exceed 25 psi (2 bar) pre minute, one or both cylinders require service. Proceed with 2000 Hour Schedule Step 7 to isolate the faulty component. CL0886.eps Disconnect the hydraulic line at the rod end of both cylinders. Cap the ports and plug the lines. 7

8 2000 Hour Schedule (continued) 7 Test the attachment cylinders. A Connect one of the hydraulic lines to its cylinder. The other line must remain plugged. B Start the truck. Hold the clamp control handle in the clamp position for a few seconds. C Return the handle to neutral. Watch the gauge pressure reading. If the gauge pressure drops more than 150 psi (10 bar) initially and an additional drop exceeds 25 psi (2 bar) per minute, the cylinder connected to the check valve is faulty and requires service. If the gauge pressure does not drop more than 150 psi (10 bar) initially and an additional drop does not exceed 25 psi (2 bar) pre minute, the second cylinder is faulty. It is recommended to perform a similar pressure test for the second cylinder before servicing. IMPORTANT: Before removing pressure gauge, momentarily actuate clamp open circuit. This will relieve pressure trapped by check valves in clamp circuit. 8 Test the attachment sideshift circuit. If the clamp does not sideshift right and left at equal speeds or drops a load while sideshifting, one of the sideshift check valve cartridges is faulty. The two outer cartridges on the top of the valve are for the sideshift circuits. IMPORTANT: Clamps equipped with solenoid adaption must be plumbed to the check valve so the solenoid will be energized for the clamp/open functions. A Install the pressure gauge and hose assembly in the valve test port marked G, located on the top of the valve body. B Start the truck. Clamp onto a load and lift no more than 1 in. (25 mm) off ground or floor. Hold the sideshift control handle in the sideshift left position for a few seconds. C Return the handle to neutral. Watch the gauge pressure reading. If the gauge pressure drops more than 150 psi (10 bar) initially and an additional drop exceed 25 psi (2 bar) per minute, the sideshift left cartridge is faulty and requires service. If the gauge pressure does not drop more than 150 psi (10 bar) initially and an additional drop does not exceed 25 psi (2 bar) pre minute, move the sideshift control handle in the sideshift right position for a few seconds. D Return the handle to neutral. Watch the gauge pressure reading. If the gauge pressure drops more than 150 psi (10 bar) initially and an additional drop exceeds 25 psi (2 bar) per minute, the sideshift right cartridge is faulty and requires service. If the gauge pressure does not drop more than 150 psi (10 bar) initially and an additional drop does not exceed 25 psi (2 bar) pre minute, the problem is not hydraulic. IMPORTANT: Before removing pressure gauge, momentarily actuate clamp open circuit. This will relieve pressure trapped by check valves in clamp circuit. 8 CL1050.eps Connect one of the hydraulic lines to its cylinder. The other line must remain plugged. WARNING: Before removing any hoses, relieve pressure in the hydraulic system. Turn truck off, then open the truck auxiliary control valves several times in both directions. Sideshift Left Cartridge Clamp Cartridge CL4348.eps Sideshift Right Cartridge

9 BLANK

10 Do you have questions you need answered right now? Call your nearest Cascade Service Department. Visit us online at AMERICAS Cascade Corporation U.S. Headquarters 2201 NE 201st Fairview, OR Tel: 800-CASCADE ( ) Fax: Cascade Canada Inc Timberlea Blvd. Mississauga, Ontario Canada L4W-4M6 Tel: Fax: Cascade do Brasil Rua João Guerra, 134 Macuco, Santos - SP Brasil Tel: Fax: EUROPE-AFRICA Cascade Italia S.R.L. European Headquarters Via Dell Artigianato Vago di Lavagno (VR) Italy Tel: Fax: Cascade (Africa) Pty. Ltd. PO Box 625, Isando A Steel Road Sparton, Kempton Park South Africa Tel: Fax: ASIA-PACIFIC Cascade Japan Ltd. 2-23, 2-Chome, Kukuchi Nishimachi Amagasaki, Hyogo Japan, Tel: Fax: Cascade Australia Pty. Ltd Ipswich Road Rocklea, QLD 4107 Australia Tel: Fax: Cascade Korea 121B 9L Namdong Ind. Complex, Gojan-Dong Namdong-Ku Inchon, Korea Tel: Fax: Cascade New Zealand 15 Ra Ora Drive East Tamaki, Auckland New Zealand Tel: Fax: Cascade-Xiamen No. 668 Yangguang Rd. Xinyang Industrial Zone Haicang, Xiamen City Fujian Province P.R. China Tel: Fax: Sunstream Industries Pte. Ltd. 18 Tuas South Street 5 Singapore Tel: Fax: Cascade India Material Handling Private Limited No 34, Global Trade Centre 1/1 Rambaugh Colony Lal Bahadur Shastri Road, Navi Peth, Pune (Maharashtra) India Phone: Fax: c Cascade Corporation Part Number R3

Installation Instructions

Installation Instructions c Installation Instructions C-Series Integral Sideshifter & K-Series Fork Positioner Installation Kits for Toyota Masts This sheet provides installation instructions for Cascade Installation Kits. Each

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Sideshifter 100F-SSS-B017 R2 cascade corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com PART NUMBER Decals 1 2 Recommended

More information

Installation Instructions

Installation Instructions c Installation Instructions Pressure Regulator Kit 6804769 This manual provides instructions for Cascade Pressure Regulator Kit 68047669 for carton clamps. The kit includes a valve, a driver operated high-low

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Multi-Purpose Clamp 8G-MCS-48 corporation For Technical Assistance call: 800-7-, Fax: 888-9-807 To Order Parts call: 888-7-, Fax: 888-9-04 OR Write: Cascade Corporation,

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Fork Positioner 55K-FPS-A011 R2 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Fork Positioner Assembly Sticker

More information

Installation Instructions

Installation Instructions c Installation Instructions Mark Radio Frequency (RF) Hydraulic Control Kit 6819446 This sheet provides installation instructions for the truck mounted component and replacement parts list for Cascade

More information

Installation Instructions

Installation Instructions c Installation Instructions K-Series Fork Positioner Termination Kits 0, 0, 0, 000 and 0 This sheet provides installation instructions and replacement parts list for Cascade High Termination Kits 0, 0,

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Carton Clamp 35D-CCS-35Q R3 corporation OR Write: Cascade Corporation, P.O. Box 2087, Portland, OR 97220 Internet: www.cascorp.com Cascade is a Registered Trademark

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Carton Clamp 35D-CCS-35A R3 corporation OR Write: Cascade Corporation, P.O. Box 2087, Portland, OR 97220 Internet: www.cascorp.com Blank Safety Decals 2 cascade 2 cascade

More information

Installation Instructions

Installation Instructions c Installation Instructions Clamp Open Guard Switch Activated Retrofit Kit 6048125 This manual provides installation instructions for Cascade Clamp Open Guard Retrofit Kit. The kit converts an existing

More information

Installation Instructions

Installation Instructions c Installation Instructions Flow Control s This sheet provides installation instructions and replacement parts list for Cascade Flow Control s. The valve reduces the flow rate to the attachment and returns

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number F-Series Sideshifter -SSS-A016 R3 cascade corporation For Technical Assistance call: 800-227-2233, Fax: 888-329-8207 To Order Parts call: 888-227-2233, Fax: 888-329-0234

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number F-Series Sideshifter -SSS-A062 R5 cascade corporation For Technical Assistance call: 800-227-2233, Fax: 888-329-8207 To Order Parts call: 888-227-2233, Fax: 888-329-0234

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Single-Double Pallet Handlers Catalog Number 5G-FDS-A R7 corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Publications OOL CATALOG

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Single-Double Pallet Handler Catalog Number 3G-FDS-B500 R6 corporation To Order Parts call: 888-7-33, Fax: 888-39-034 OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Single-Double Pallet Handler Catalog Number 5G-FDS-B R9 cascade corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Publications OOL

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Paper Roll Clamp 3H-RTF-AX8-00 cascade corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com 5 3 4 Decals 7 8 C-67554-4

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Fork Positioner 55K-FPS-A330 R0 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Blank All dealerships with an

More information

Installation Instructions

Installation Instructions c Installation Instructions Sequential Loop -Position Electronic Pressure Regulator Kits This manual provides instructions for Cascade Electronic Pressure Regulator and Indicator System. The kits provide

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Paper Roll Clamp H-RCF-AQ008 cascade corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com 5 4 Decals 7 8 C-67554-4 RC860.ai

More information

Installation Instructions

Installation Instructions c Installation Instructions Electronic Pressure Regulator Kits with Backhand Relief This manual provides instructions for Cascade Electronic Pressure Regulator with backhand relief and Indicator System.

More information

Installation Instructions

Installation Instructions c Installation Instructions -Position Electronic Pressure Regulator Kits This manual provides instructions for Cascade Electronic Pressure Regulator and Indicator System. The kits provide selectable clamp

More information

H2R and H2L Cable Reel

H2R and H2L Cable Reel c Installation Service and Parts Manual H2R and H2L Cable Reel Serial Numbers 678971 through 678972 Part Number 679932-R1 cascade corporation For Technical Assistance call: 800-227-2233, Fax: 888-329-8207

More information

Installation Instructions

Installation Instructions c Installation Instructions Light Kits for Three-Position Pressure Relief Valve 0 This manual provides installation instructions for, or Kits used with -Position Pressure Relief Valve 0. The switch box

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number Fork Positioner 55K-FPS-A086 R2 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with an open

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Revolving Fork Clamp (VOLVO) Catalog Number 52G74364 cascade corporation OR Write: Cascade Corporation, P.O. Box 2087, Portland, OR 97220 Internet: www.cascorp.com All dealerships

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Roll Clamp 8H-RCP-A003 R3 corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com 3 Decals 7 8 C-7- RC380.ai 3 C-7-9-R @

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model 36G-CCT Tipping Clamp Catalog Number 36G74237 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Blank 1 Safety Decals 4 1 3 2

More information

Parts Manual. cascade. corporation. Model. 120H Tower Roll Clamp 120H Catalog Number

Parts Manual. cascade. corporation. Model. 120H Tower Roll Clamp 120H Catalog Number c Parts Manual Model Catalog Number 0H Tower Roll Clamp 0H74584 corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com 5 4 Decals 7 8 C-7554-4 RC80.ai 4 5 C-7554-5595-R

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number 45G Rotator 45G-RRB-0A R corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com All dealerships with an open account, please

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Paper Roll Clamp 0H-RBP-B0 corporation For Technical Assistance call: 800-7-, Fax: 888-9-807 To Order Parts call: 888-7-, Fax: 888-9-04 OR Write: Cascade Corporation,

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Paper Roll Clamp 0H-RCF-BX-0 corporation OR Write: Cascade Corporation, P.O. Box 08, Portland, OR 90 Internet: www.cascorp.com Decals 8 C-- RC80.ai C-- 9-R @ Disengaged

More information

Parts Manual. cascade. corporation. Model. Paper Roll Clamp 10H-RCP-A010. Catalog Number

Parts Manual. cascade. corporation. Model. Paper Roll Clamp 10H-RCP-A010. Catalog Number c Parts Manual Model Catalog Number Paper Roll Clamp 10H-RCP-A010 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com 3 Decals 1 2 7 5 RC5371.eps 1 7

More information

Installation Instructions

Installation Instructions c Installation Instructions Clamp Open Guard Kits 6008230-12V, 6018016-24V, 6018017-36V, 6018012-48V This manual provides installation instructions for Cascade Clamp Open Guard. The kit prevents the accidental

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Push/Pull - Ext Range Catalog Number E-PXS-3 cascade corporation OR Write: Cascade Corporation, P.O. Box 2017, Portland, OR 97220 Internet: www.cascorp.com Cascade is a Registered

More information

Parts Manual. cascade. corporation. 50D Fork Clamp. Model 50D-CFR-123. Serial Number

Parts Manual. cascade. corporation. 50D Fork Clamp. Model 50D-CFR-123. Serial Number c Parts Manual Model Serial Number 0D Fork Clamp 0D-CFR- corporation For Technical Assistance call: 800-7-, Fax: 888-9-807 To Order Parts call: 888-7-, Fax: 888-9-0 OR Write: Cascade Corporation, P.O.

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number 5G Rotating Clamp 5G-RSS-A-7475 cascade corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Blank Safety Decals WARNING:

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number QFM Push/Pull E-QLB-Q00 R cascade corporation To Order Parts call: 888-7-, Fax: 888-9-0 OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com

More information

Parts Manual. cascade. corporation. Model. Roll Clamp 38H-RCP-3A Catalog Number

Parts Manual. cascade. corporation. Model. Roll Clamp 38H-RCP-3A Catalog Number c Parts Manual Model Catalog Number Roll Clamp 8H-RCP-A-000 cascade corporation For Technical Assistance call: 800-7-, Fax: 888-9-807 To Order Parts call: 888-7-, Fax: 888-9-04 OR Write: Cascade Corporation,

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Paper Roll Clamp H-RDP-B0 R0 cascade corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com 5 4 Decals 7 8 C-67554-4 RC860.ai

More information

Application Engineering Department Special Product. 170D-CFR Fork Clamp - Revolving

Application Engineering Department Special Product. 170D-CFR Fork Clamp - Revolving Parts Manual For units with serial# 2177229 2226222 Application Engineering Department Special Product 170D-CFR-66999 Fork Clamp - Revolving FEATURES:..Integral mounting includes rollers, chain anchors

More information

Portable Digital Clamp Force Indicator

Portable Digital Clamp Force Indicator O PERATOR S GUIDE Portable Digital Clamp Force Indicator Manual Number 6094544-R1 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Page Introduction i Key Functions

More information

D-Series. Sideshifters NSTALLATION INSTRUCTIONS. cascade PERIODIC MAINTENANCE. corporation Cascade is a Registered Trademark of Cascade Corporation

D-Series. Sideshifters NSTALLATION INSTRUCTIONS. cascade PERIODIC MAINTENANCE. corporation Cascade is a Registered Trademark of Cascade Corporation I and NSTALLATION INSTRUCTIONS PERIODIC MAINTENANCE D-Series Sideshifters Manual Number 672358-R7 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Page INSTALLATION

More information

Parts Manual. cascade. corporation. Model. Paper Roll Clamp 20H-RTF-A01X-149. Catalog Number

Parts Manual. cascade. corporation. Model. Paper Roll Clamp 20H-RTF-A01X-149. Catalog Number c Parts Manual Model Catalog Number Paper Roll Clamp 0H-RTF-A0X-9 cascade corporation For Technical Assistance call: 800-7-33, Fax: 888-39-807 To Order Parts call: 888-7-33, Fax: 888-39-03 OR Write: Cascade

More information

TRI - LATERAL HEAD UNIT SPARE PARTS MANUAL

TRI - LATERAL HEAD UNIT SPARE PARTS MANUAL TRI - LATERAL HEAD UNIT SPARE PARTS MANUAL Model Manual Part Number Trilateral Unit 20A8441 BLANK PAGE 1 SPARE PARTS LIST CONTENTS INDEX Frame Group Section 1.0.0 Arm Group Section 2.0.0 Fork Carriage

More information

Installation Instructions

Installation Instructions c Installation Instructions G-Series Rotator Seal Replacement This sheet provides instructions on replacing the base unit seal with the new seal assembly. The seal assembly is a rubber seal with a steel

More information

c Technical Bulletin cascade corporation Applications for Bronze Bearings and Lower Hooks TB 296 May 2015 Lower Hooks Upper Bearings Lower Bearings

c Technical Bulletin cascade corporation Applications for Bronze Bearings and Lower Hooks TB 296 May 2015 Lower Hooks Upper Bearings Lower Bearings 228782 c Technical Bulletin TB 296 May 2015 Applications for Bronze Bearings and Lower Hooks This sheet provides information on applications for bronze bearings and hooks. Cascade recommends bronze bearings

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Paper Roll Clamp H-RCP-B005 R0 corporation For Technical Assistance call: 800-7-, Fax: 888-9-807 To Order Parts call: 888-7-, Fax: 888-9-0 OR Write: Cascade Corporation,

More information

Parts Manual. cascade. corporation. Model. Fork Positioner 45D-FPB-109. Catalog Number

Parts Manual. cascade. corporation. Model. Fork Positioner 45D-FPB-109. Catalog Number c Parts Manual Model Catalog Number Fork Positioner 45D-FPB-09 cascade corporation To Order Parts call: 888-7-, Fax: 888-9-04 OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com

More information

Stationary Load Inverter

Stationary Load Inverter I NSTALLATION & OPERATION Stationary Load Inverter Manual Number 6099892 cascade corporation Cascade is a Registered Trademark of Cascade Corporation Co n t e n t s Page Number INSTALLATION INSTRUCTIONS

More information

Portable Clamp Force Indicator

Portable Clamp Force Indicator O PERATOR S GUIDE Portable Clamp Force Indicator Manual Number 6074874-R1 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C TENTS Page Introduction i Key Functions 1 Setup

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number 90F Paper Roll Clamp 90F-RC-0C_(SN_09) cascade corporation OR Write: Cascade Corporation, P.O. Box 08, Portland, OR 90 Internet: www.cascorp.com Decalcomanie Safety

More information

Parts Manual. cascade. corporation. Model. Tower Roll Clamp 45H-TCS-4A R5. Catalog Number

Parts Manual. cascade. corporation. Model. Tower Roll Clamp 45H-TCS-4A R5. Catalog Number c Parts Manual Model Catalog Number Tower Roll Clamp H-TCS-A-97 R cascade corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Blank Decals 7 8 C-67- RC860.ai

More information

Installation Instructions

Installation Instructions c Installation Instructions -osition Electronic ressure Regulator Kits his manual provides instructions for Cascade -osition Electronic ressure Regulator and Indicator System. he kit provides selectable

More information

F-Series. Fixed & Swing Frame Paper Roll Clamps ERIODIC MAINTENANCE. cascade. corporation. Manual Number

F-Series. Fixed & Swing Frame Paper Roll Clamps ERIODIC MAINTENANCE. cascade. corporation. Manual Number P ERIODIC MAINTENANCE F-Series Fixed & Swing Frame Paper Roll Clamps Manual Number 6045734 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Page INTRODUCTION Introduction

More information

Carton Clamps with Folding Forks

Carton Clamps with Folding Forks I and NSTALLATION INSTRUCTIONS PERIODIC MAINTENANCE Carton Clamps with Folding Forks Manual Number 6810419 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Introduction

More information

300J Integral PERATOR'S GUIDE. Fork Positioner & Load Stabilizer. cascade. corporation Cascade is a Registered Trademark of Cascade Corporation

300J Integral PERATOR'S GUIDE. Fork Positioner & Load Stabilizer. cascade. corporation Cascade is a Registered Trademark of Cascade Corporation O PERATOR'S GUIDE 300J Integral Fork Positioner & Load Stabilizer Manual No. 6055810-R1 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ontents Page Introduction i Safety

More information

F-Series. Fork Positioners NSTALLATION INSTRUCTIONS. cascade. and PERIODIC MAINTENANCE. corporation. Manual Number R4

F-Series. Fork Positioners NSTALLATION INSTRUCTIONS. cascade. and PERIODIC MAINTENANCE. corporation. Manual Number R4 NSTLLTON NSTRUCTONS and PERODC MNTENNCE F-Series Fork Positioners Manual Number 207363-R4 cascade corporation Cascade is a Registered Trademark of Cascade Corporation T RUCK REQUREMENTS Truck Relief Setting

More information

Installation Instructions

Installation Instructions c Installation Instructions All steps of these instructions must be carefully followed to preserve warranty coverage. UL Classified Power / Communication Groups This manual provides installation instructions

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number Fork Positioner 100D-FPB-04C R1 cascade corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Base Unit Group 1 2 3

More information

perator s Guide Forward Bin Dumper cascade corporation Manual Number R1 Cascade is a Registered Trademark of Cascade Corporation

perator s Guide Forward Bin Dumper cascade corporation Manual Number R1 Cascade is a Registered Trademark of Cascade Corporation O perator s Guide D-Series Forward in Dumper Manual Number 217562-R1 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ontents Introduction 1 Safety Rules 2 Daily Inspection

More information

Battery. For Technical Support... To Order Parts... Call: Fax: Call: Fax:

Battery. For Technical Support... To Order Parts... Call: Fax: Call: Fax: c Installation Instructions & Operators Guide Wireless Pressure Monitor Kits This sheet provides instruction on installing Cascade Wireless Pressure Monitor Kit. This kit consists of a transmitter, display

More information

PERATOR S GUIDE. C, D&E-Series. Carton Clamps. Manual Number R4. cascade. corporation Cascade is a registered Trademark of Cascade Corporation

PERATOR S GUIDE. C, D&E-Series. Carton Clamps. Manual Number R4. cascade. corporation Cascade is a registered Trademark of Cascade Corporation O PERATOR S GUIDE C, D&E-Series Carton Clamps Manual Number 210273-R4 cascade corporation Cascade is a registered Trademark of Cascade Corporation C ONTENTS Introduction 1 Safety Rules 2 Daily Inspection

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Fork Positioner 120K-FPS-C023 R1 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Fork Positioner Assembly Sticker

More information

Installation and Service Manual

Installation and Service Manual Installation and Service Manual THINLINE 4 Port Hose Reel l Manual Number 675395 R-1 cascade@ Cascade is a Registered Trademark of Cascade Corporation l THINLINE is a Trademark of Cascade Corporation Contents.

More information

Installation Instructions

Installation Instructions c Installation Instructions Tilt ontrol Mounting Locations for Specific Lift Trucks This sheet provides specific mounting locations for ascade Tilt ontrol. The tilt control positions the mast or attachment

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Fork Positioner 55K-FPS-A058 R0 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Fork Positioner Assembly Sticker

More information

F-Series. Swing Frame Paper Roll Clamps NSTALLATION INSTRUCTIONS. cascade. and PERIODIC MAINTENANCE. corporation. Manual Number R-4

F-Series. Swing Frame Paper Roll Clamps NSTALLATION INSTRUCTIONS. cascade. and PERIODIC MAINTENANCE. corporation. Manual Number R-4 INSTRUCTIONS and PERIODIC MAINTENANCE F-Series Swing Frame Paper Roll Clamps Manual Number 674511 R-4 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Introduction

More information

Parts Manual. cascade. corporation. 100F Sideshifter. Model 100F-SSS-B084 R1. Catalog Number

Parts Manual. cascade. corporation. 100F Sideshifter. Model 100F-SSS-B084 R1. Catalog Number c Parts Manual Model Catalog Number 100F Sideshifter 100F-SSS-B084 R1 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with an open

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Integral Fork Positioner Catalog Number 55K-IFS-A130 R0 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model 65K Fork Positioner Catalog Number 65K-FPS-B003 R1 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with an

More information

Hydraulic Force Control

Hydraulic Force Control U SER MANUAL Hydraulic Force Control Pressure Balancing Full Free Lift Masts Manual Number 6801696-R5 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Page OVERVIEW

More information

D-Series Clamps PERATOR'S GUIDE. Sideshifting, Non-Sideshifting, Revolving, Turnafork ȚM Turnaload ȚM Bulk Box Handler, Marble Handler, Tipping

D-Series Clamps PERATOR'S GUIDE. Sideshifting, Non-Sideshifting, Revolving, Turnafork ȚM Turnaload ȚM Bulk Box Handler, Marble Handler, Tipping O PERATOR'S GUIDE D-Series Clamps Sideshifting, Non-Sideshifting, Revolving, Turnafork ȚM Turnaload ȚM Bulk Box Handler, Marble Handler, Tipping Manual No. 672944-R9 cascade corporation Cascade is a Registered

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Single-Double Pallet Handler Catalog Number 5G-FDS-A013 R6 corporation OR Write: Cascade Corporation, P.O. Box 0187, Portland, OR 970 Internet: www.cascorp.com Publications OOL CATALOG

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Fork Positioner 55K-FPS-A469 R2 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Fork Positioner Assembly Sticker

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Fork Positioner 55K-FPS-A223 R1 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with an open

More information

Installation Instructions General Fork Installation

Installation Instructions General Fork Installation c Installation Instructions General Fork Installation This manual describes the installation of forks for Rotating, Sideshifting, and Fork Positioning attachments. Middle hooks must be properly welded

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number 65F Sideshifter 65F-SSS-B796 R1 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com I NSPECTION & MAINTENANCE WARNING:

More information

SER MANUAL. Trilateral Head. Manual Number cascade. corporation Cascade is a Registered Trademark of Cascade Corporation

SER MANUAL. Trilateral Head. Manual Number cascade. corporation Cascade is a Registered Trademark of Cascade Corporation U SER MANUAL Trilateral Head Manual Number 6898350 cascade corporation Cascade is a Registered Trademark of Cascade Corporation CONTENTS Page INTRODUCTION 1 Special Definitions 1 USING THE MANUAL 2 TECHNICAL

More information

PERATOR'S GUIDE. Rotators. & Bin Retainer. Manual No R4. cascade. corporation Cascade is a Registered Trademark of Cascade Corporation

PERATOR'S GUIDE. Rotators. & Bin Retainer. Manual No R4. cascade. corporation Cascade is a Registered Trademark of Cascade Corporation O PERATOR'S GUIDE Rotators & Bin Retainer Manual No. 672714-R4 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Introduction i Safety Rules 1 Daily Inspection 3 Fork

More information

NSTALLATION INSTRUCTIONS. Fixed Frame Pivot Arm Paper Roll Clamps. cascade PERIODIC MAINTENANCE

NSTALLATION INSTRUCTIONS. Fixed Frame Pivot Arm Paper Roll Clamps. cascade PERIODIC MAINTENANCE I and NSTALLATION INSTRUCTIONS PERIODIC MAINTENANCE 3H Fixed Frame Pivot Arm Paper Roll Clamps Manual Number 6912143 cascade corporation Cascade is a Registered Trademark of Cascade Corporation CONTENTS

More information

Upending Roll Clamps NSTALLATION INSTRUCTIONS. cascade PERIODIC MAINTENANCE. corporation. Manual Number R1

Upending Roll Clamps NSTALLATION INSTRUCTIONS. cascade PERIODIC MAINTENANCE. corporation. Manual Number R1 I and NSTLLTION INSTRUCTIONS PERIODIC MINTENNCE Upending Roll Clamps Manual Number 6837771-R1 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Recommended Hydraulic

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Bale Clamp 40D-BCB-55A R0 corporation OR Write: Cascade Corporation, P.O. Box 2087, Portland, OR 97220 Internet: www.cascorp.com Cascade is a Registered Trademark of

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Single-Double Pallet Handler Catalog Number G-FDS-A R6 corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Publications OOL CATALOG

More information

Sliding Arm Paper Roll Clamps

Sliding Arm Paper Roll Clamps I and NSTLLTION INSTRUTIONS PERIODI MINTENNE Sliding rm Paper Roll lamps Manual Number 6827242-R2 cascade corporation ascade is a Registered Trademark of ascade orporation ONTENTS Recommended Hydraulic

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Single-Double Pallet Handler Catalog Number 5G-FDS-88 corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Publications OOL CATALOG T

More information

D,F,G & H-Series PERATOR'S GUIDE. Fixed Frame Paper Roll Clamps. cascade. corporation. Manual Number R9

D,F,G & H-Series PERATOR'S GUIDE. Fixed Frame Paper Roll Clamps. cascade. corporation. Manual Number R9 O PERATOR'S GUIDE D,F,G & H-Series Fixed Frame Paper Roll Clamps Manual Number 210135-R9 cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Page Introduction 1 Safety

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Catalog Number Roll Clamp 90F7 corporation OR Write: Cascade Corporation, P.O. Box 087, Portland, OR 970 Internet: www.cascorp.com Safety Decals cascade RC0.eps cascade SHORT ARM Can

More information

Installation Instructions

Installation Instructions c Installation Instructions ll steps of these instructions must be carefully followed to preserve warranty coverage. UL Classified Power / Communication Groups This manual provides installation instructions

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number Fork Positioner 55K-FPS-A030 R1 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Fork Positioner Assembly Sticker

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Integral Fork Positioner Serial Number 35K-IFS-A090 R0 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model F-Series Sideshifter Serial Number -SSS-A087R5 corporation For Technical Assistance call: 800-227-2233, Fax: 888-329-8207 To Order Parts call: 888-227-2233, Fax: 888-329-0234 OR Write:

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number Fork Positioner -FPS-A141 R0 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com Cascade is a Registered Trademark

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number Carton Clamp 25D-CCS-33A R2 corporation OR Write: Cascade Corporation, P.O. Box 2087, Portland, OR 97220 Internet: www.cascorp.com Cascade is a Registered Trademark of

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number Revolving Drum Clamp D-DFR-AR0 corporation To Order Parts call: 888--, Fax: 888-9-0 OR Write: Cascade Corporation, P.O. Box 08, Portland, OR 90 Internet: www.cascorp.com

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Fork Positioner Serial Number 70K-IFS-B087 R2 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with an open

More information

ERVICE MANUAL. D-Series. Forward Bin Dumper. Manual Number cascade Cascade is a Registered Trademark of Cascade Corporation

ERVICE MANUAL. D-Series. Forward Bin Dumper. Manual Number cascade Cascade is a Registered Trademark of Cascade Corporation S ERVICE MANUAL D-Series Forward Bin Dumper Manual Number 219472 cascade Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Page INTRODUCTION, Section 1 Introduction, 1.1 1 Special Definitions,

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Serial Number F-Series Sideshifter -SSS-A147R0 cascade corporation For Technical Assistance call: 800-227-2233, Fax: 888-329-8207 To Order Parts call: 888-227-2233, Fax: 888-329-0234

More information

Layer Picker. Swing, Stationary Side Mount, Carriage Mount, and Fork Mount Models. perator s Guide. cascade

Layer Picker. Swing, Stationary Side Mount, Carriage Mount, and Fork Mount Models. perator s Guide. cascade O perator s Guide Layer Picker Swing, Stationary Side Mount, Carriage Mount, and Fork Mount Models Manual Number cascade corporation Cascade is a Registered Trademark of Cascade Corporation C ONTENTS Introduction

More information

Parts Manual. cascade

Parts Manual. cascade c Parts Manual Model Integral Fork Positioner Serial Number 70K-IFS-B094 R0 corporation OR Write: Cascade Corporation, P.O. Box 20187, Portland, OR 97220 Internet: www.cascorp.com All dealerships with

More information