PREMIUM Series Belt Drive Wi-Fi Garage Door Opener

Transcription

1 PREMIUM Series Belt Drive Wi-Fi Garage Door Opener Model 8355WRGD 1/2 hp FOR RESIDENTIAL USE ONLY Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door after installation. The door WILL NOT CLOSE unless the Protector System is connected and properly aligned. Periodic checks of the garage door opener are required to ensure safe operation. This garage door opener is ONLY compatible with MyQ and Security+ 2.0 accessories. DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended devices and features are to be used ONLY with sectional doors. Attach warning labels to the location indicated on label. CONTENTS Preparation Assembly Installation Install the Door Control Install the Protector System Power Adjustments Operation Connect With Your Smartphone Maintenance Troubleshooting Accessories Warranty Automatic Garage Door Opener Safety & Maintenance Guide Repair Parts SERIAL NUMBER: Please write the MyQ Serial number in the box above. See page 2. Register online at: Raynor Garage Doors 1101 E. River Road Dixon, Illinois 61021

2 MyQ Serial Number: Product Serial Number: Date of Purchase: / / MyQ Serial Number Product Serial Number

3 Check Signal Strength. If you see: Wi-Fi signal is strong. The garage door opener will connect to your Wi-Fi network. Wi-Fi signal is weak. The garage door opener may connect to your Wi-Fi network. If not, try one of the options below to improve the Wi-Fi signal: No Wi-Fi signal. The garage door opener will not be able to connect to your Wi-Fi network. Try one of the options below to improve the Wi-Fi signal: Move your router closer to the garage door opener to minimize interference from walls and other objects Buy a Wi-Fi range extender Torsion Spring OR Extension Spring

4 5/32 3/16 5/16 7/16 1/2 5/8 7/16 9/16 1/4

5 A B C F D G E K H L Not M Provided J N O Not Provided P I

6 HARDWARE Washered Bolt 5/16"-18x1/2" (Mounted in the garage door opener) Lock Nut (Mounted in the garage door opener) Hex Screw #8x3/8" (Packed with the sprocket cover) Washered Bolt 5/16"-18x1/2" Lock Nut Hex Screw #8x3/8"

7 1 2 Spring Trolley Nut (To motor unit) Nut ring slot 3 Nut Ring Nut Ring BEFORE 1" (2.5 cm) AFTER RELEASE 1-1/4" (3.18 cm)

8

9 Unfinished Ceiling Header Wall Vertical Centerline of Garage Door Level (Optional) 2x4 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET Structural Supports Header Wall Track Highest Point of Travel Door 2" (5 cm) Sectional door with curved track

10 HARDWARE Lag Screw 5/16"-9x1-5/8" Ceiling Mounting Holes Header Bracket 6" (15 cm) Maximum (Finished Ceiling) Wall Mount 2x4 Structural Support Horizontal Line (Header Wall) Header Bracket Vertical Centerline of Garage Door Lag Screw 5/16"-9 x 1-5/8" Door Spring Door Spring (Garage Door) Vertical Centerline of Garage Door Lag Screw 5/16"-9 x 1-5/8" (Header Wall) Optional Mounting Holes Highest Point of Garage Door Travel (Garage Door)

11 HARDWARE Clevis Pin 5/16" x 2-3/4" Ring Fastener Ring Fastener Clevis Pin 5/16" X 2-3/4" Connected Disconnected

12 HARDWARE Lock Washer 5/16" Hex Bolt 5/16"- 18x7/8" Nut 5/16"-18 FIGURE 1 FIGURE 2 Unfinished Ceiling Finished Ceiling FIGURE 3 Not Provided (Not Provided) Lag Screws 5/16"- 18x1-7/8" Measure Distance Hex Bolt 5/16"- 18x7/8", Lock Washer 5/16", Nut 5/16"-18

13 or or Trolley Release Arm

14 HARDWARE FIGURE 1 Vertical Reinforcement Door Bracket FIGURE 3 Vertical Centerline of Garage Door UP Self-Threading Screw 1/4"-14 x 5/8" Vertical Centerline of Garage Door UP Self-Threading Screw 1/4"-14 x 5/8" Self-Threading Screw 1/4"-14 x 5/8" FIGURE 2 Vertical Reinforcement Bolt 5/16"-18 x 2" (Not provided) FIGURE 4 Bolt 5/16"-18 x 2" (Not provided) Door Bracket Lock Washer 5/16" Nut 5/16"-18 Vertical Centerline of Garage Door Vertical Centerline of Garage Door UP Inside Edge of Door or Reinforcement Board UP

15 Hex Bolt 5/16"-18 x 7/8" CORRECT Nut 5/16"-18 Straight Door Arm (Groove facing out) Curved Door Arm HARDWARE Lock Washer 5/16" INCORRECT Ring Fastener Straight Door Arm Clevis Pin 5/16" x 1-1/4" Clevis Pin 5/16" x 1" Curved Door Arm Ring Fastener Nut 5/16"-18 Lock Washer 5/16" Clevis Pin 5/16" x 1" Hex Bolt 5/16"-18 x 7/8" Clevis Pin 5/16" x 1-1/4"

16 /16" (11 mm) Wall Screw 6-32 x 1" (2) Drywall Anchors (2) HARDWARE Screw 6AB x 1" (2) 4-5 DRYWALL GANG BOX 6 Drywall Anchor 6-32 x 1" 6AB x 1" 7 8 DRYWALL Drywall Anchor 6AB x 1" GANG BOX 6-32 x 1"

17 HARDWARE HARDWARE Insulated Staple (Not Shown) 1 2 7/16" (11 mm) Clevis Pin 5/16" x 2-3/4" Ring Fastener Ring Fastener Staple Clevis Pin 5/16" X 2-3/4" 3 RED WHITE WHITE GREY

18 Safety Reversing Sensor 6" (15 cm) max. above floor Invisible Light Beam Protection Area Safety Reversing Sensor 6" (15 cm) max. above floor

19 HARDWARE Carriage Bolt 1/4"-20 x 1/2" Wing Nut 1/4" (Not provided) No more than 6 inches (15 cm) Inside Garage Wall (Not provided) No more than 6 inches (15 cm) Carriage Bolt 1/4"-20 x 1/2" Wing Nut 1/4"-20 Lens Carriage Bolt 1/4"-20 x 1/2" Wing Nut 1/4"-20

20 D 1 2 (Not provided) Inside Garage Wall HARDWARE Insulated Staple (Not Shown) 3 4 Carriage Bolt 1/4"-20 x 1/2" Wing Nut 1/4" Staple 7/16" (11 mm) 3 RED W

21 R D 1 Safety reversing sensor wires 3 Safety reversing sensor wires White White/Black Pre-installed wires 2 7/16" (11 mm) Not Provided Pre-installed wires Yellow (for example) Purple (for example) 4 Yellow 5 Yellow (for example) Purple (for example) Purple 7/16" (11 mm) RED WHITE WHITE GREY To insert or remove the wires from the terminal, push in the tab with a screwdriver tip.

22 TYPICAL WIRING PERMANENT WIRING Ground Tab Green Ground Screw Ground Wire White Wire Black Wire Black Wire

23 1 2 3 If the receiving sensor is in direct sunlight, switch it with sending sensor so it is on the opposite side of the door. 1 2 RED WHITE WHITE GREY (invisible light beam) Amber LED SENDING SENSOR Green LED RECEIVING SENSOR

24 PROGRAMMING BUTTONS UP Button Adjustment Button DOWN Button UP (Open) DOWN (Close)

25 PROGRAMMING BUTTONS UP Button Adjustment Button DOWN Button

26

27

28

29 Learn Button LED An LED on the garage door opener will indicate Wi-Fi status. See table below. Learn Button Command LED

30 Push Bar SERVICE LED LEARN Button LOCK Button COMMAND LED LIGHT Button

31 Command LED LOCK Button LOCK Button LIGHT Button Service LED LEARN Button LIGHT Button Command LED

32 4GHI 5JKL 7PRS 8TUV 9WXY 0 QZ * # ENTER 6 MNO 1 2 LEARN LED LEARN Button click click 1 LEARN button Command LED 2 0 QZ * # OR ENTER???? PIN

33 NOTICE LEARN Button Black Adjustment Button NOTICE

34 Maintenance Maintenance Schedule EVERY MONTH Manually operate door. If it is unbalanced or binding, call a trained door systems technician. Check to be sure door opens and closes fully. Adjust if necessary, see page 25. Test the safety reversal system. Adjust if necessary, see page 26. EVERY YEAR Oil door rollers, bearings and hinges. The garage door opener does not require additional lubrication. Do not grease the door tracks. EVERY TWO TO THREE YEARS Use a rag to wipe away the existing grease from the garage door opener rail. Reapply a small layer of white lithium grease to the top and underside of the rail surface where the trolley slides. NOTICE: Thisdevice complieswith Part15 ofthe FCCrulesand IndustryCanada slicense-exemptrsss. Operation issubjectto the following two conditions: (1)thisdevice maynotcause harmfulinterference, and (2)thisdevice mustacceptanyinterference received, including interference thatmaycause undesired operation. Anychangesormodificationsnotexpresslyapproved bythe partyresponsible forcompliance could void the user sauthorityto operate the equipment. Thisdevice mustbe installed to ensure a minimum20 cm(8 in.)distance ismaintained between users/bystandersand device. Thisdevice hasbeen tested and found to complywith the limitsfora ClassBdigitaldevice, pursuantto part15 ofthe FCCrulesand IndustryCanada ICESstandard. These limitsare designed to provide reasonable protection againstharmfulinterference in a residentialinstallation. Thisequipmentgenerates, usesand can radiate radio frequencyenergyand, ifnotinstalled and used in accordance with the instructions, maycause harmfulinterference to radio communications. However, there isno guarantee that interference willnotoccurin a particularinstallation. Ifthisequipmentdoescause harmfulinterference to radio ortelevision reception, which can be determined byturning the equipmentoffand on, the userisencouraged to tryto correctthe interference byone ormore ofthe following measures: Reorientorrelocate the receiving antenna. Increase the separation between the equipmentand receiver. Connectthe equipmentinto an outleton a circuitdifferentfromthatto which the receiverisconnected. Consultthe dealeroran experienced radio/tvtechnician forhelp. The Remote Control Battery To prevent possible SERIOUS INJURY or DEATH: NEVER allow small children near batteries. If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: Replace ONLY with 3V CR2032 coin batteries. DO NOT recharge, disassemble, heat above 212 F (100 C) or incinerate. To replace the battery, pry open the case in the middle, then at each side with the visor clip. Insert replacement battery positive side up (+). Replace the batteries with only 3V CR2032 coin cell batteries. Dispose of old batteries properly. 34

35

36

37 Accessories MAX ACCESSORIES Compatible with Raynor garage door openers manufactured since MGX 893RGX MAX Wireless Keyless Entry: For use outside of the home to enable access to the garage using a 4-digit PIN. 3-Button MAX Remote Control: Includes visor clip. MyQ ACCESSORIES 823LM Remote Light Switch: Automatically control your lights using your garage door opener, a Security+ 2.0 remote control or a MyQ Internet Gateway. Simply replaces your current wired wall switch. 825LM 829LM Remote Light Control: Automatically control your lights using your garage door opener, a Security+ 2.0 remote control or a MyQ Internet Gateway. Plugs into any interior outlet. Garage and Gate Monitor: Monitor open/closed status for up to 4 MyQ compatible garage door openers or gate operators and close them from anywhere in the home. STANDARD ACCESSORIES 041A A Extension Brackets: (Optional) For safety reversing sensor installation onto the wall or fl oor. Security+ 2.0 Wireless Door Control: Push bar, light feature and auxiliary button. Includes battery. Security+ 2.0 compatible. 37

38

39 Automatic Garage Door Opener Safety & Maintenance Guide Garage Door Opener Safety An Automatic Decision A garage door is the largest moving object in the home. An improperly adjusted garage door and opener can exert deadly force when the door closes which could lead to entrapment of children or adults and subsequent injury or death. Proper installation, operation, maintenance, and testing of the garage door and automatic opener are necessary to provide a safe, trouble-free system. Careless operation or allowing children to play with or use garage door opener controls are also dangerous situations that can lead to tragic results. A few simple precautions can protect your family and friends from potential harm. Please review the safety and maintenance tips in this guide carefully and keep it for reference. Check the operation of your garage door and opener to ensure they function in a safe and trouble-free manner. Be sure to read all Important Safety Information found in your garage door opener s manual as it provides more details and safety considerations than can be supplied with this guide. Garage Door Openers are Not Toys Discuss garage door and opener safety with your children. Explain the danger of being trapped under the door. Stay away from a moving door. The wall-mounted push button should be out of reach of children, at least 5 feet from the nearest standing surface and away from all moving parts. Mount and use the button where you can clearly see the closing garage door. Keep transmitters and remote controls out of reach of children. Do not let children play with or use transmitters or other remote control devices. Keep the door in sight until it completely closes when using the wall-mounted push button or transmitter. 39

40 Routine Maintenance Can Prevent Tragedies Make monthly inspection and testing of your garage door and opener system a part of your regular routine. Review your owner s manual for both the door and door opener. If you don t have the owner s manuals, contact the manufacturer(s) and request a copy for your specifi c model(s). Look for the opener model number on the back of the power unit. WARNING Springs are under high tension. Only qualified individuals should adjust them. Visually check the door and installation: Starting with the door in the closed position, use the manual disconnect on the opener to disconnect the door. Look for signs of wear or damage on hinges, rollers, springs, and door panels. These parts may require periodic lubrication. Check the owner s manual for suggested maintenance. If any signs of damage are evident, contact a trained door systems technician for assistance. Verify the photoeye height is no higher than 6" from the garage fl oor. Test the door for proper operation: Open and close the door manually using handles or suitable gripping points. The door should move freely and without diffi culty. The door should balance and stay partially open 3 4 feet above the fl oor. If you detect any signs of improper operation, contact a trained door systems technician for assistance. Test the opener safety features: 2 1 Reconnect the opener to the door using the manual disconnect and open the door. Place a 2x4 board fl at in the path of the door (1) and try to close it (2). The door should stop when it comes in contact with the 2x4 and then reverse direction. Block the photoelectric sensor by waving an object in front of the sensor and attempt to close the door. The door should not close unless the wall-mounted push button is manually held during operation. If the opener does not perform as described, contact a trained door systems technician for assistance. 40

41 Repair Parts Rail Assembly Parts Installation Parts Description Part Number 1 Belt - for 7 foot door 041A A Belt - for 8 foot door Belt - for 10 foot door 041A A 041A A 2 Belt Pulley Bracket 041B Master Link 004A One-Piece Rail G feet (2.1 m) One-Piece Rail G feet (2.4 m) One-Piece Rail G feet (3 m) 5 Trolley Assembly 041B3869-3A Includes: Master Link (2) Clevis Pin (1), Ring (1), Belt Clip (1), Threaded Shaft (1), Tensioner Assembly (1) 6 Tensioner Assembly 041B4103 Not Shown Owner s Manual 114A Description Part Number 1 Curved Door Arm 041B0035B 2 Door Bracket with Clevis 041A Pin and Fastener 3 Emergency Release Rope 041A2828 and Handle 4 Header Bracket with 041A Clevis Pin and Fastener 5 Remote Control Visor K029B0137 Clip 6 Safety Sensor Bracket 041A Safety Sensor Kit 041A5034 Receiving and sending sensors with 2-conductor wire 8 Straight Door Arm 4178B0034B 9 White and Red/White 041B Wire 10 3V CR2032 Lithium K010A0020 Battery 11 Remote Control 893RGX 12 Multi-function Door Control 882RGDW

42 Repair Parts Garage Door Opener Parts - Aviator II 1 Description Part Number 1 Sprocket Cover 041A Gear and Sprocket Assembly 041A Drive and Worm Gear 041A Line Cord 041B End Panel 041A Light Socket 041C Light Lens 041A Capacitor 030B Capacitor Bracket K012A Motor with Travel Module 041A Travel Module 041D Cover 041D Receiver Logic Board 050ACTWF 14 Logic Board End Panel 041D8198 Not Shown Terminal Block 041A3150 Contact Information 12 Address repair parts order to: RAYNOR GARAGE DOORS 1101 East River Road Dixon, IL For installation and service information call: Or visit us online at: Before calling, please have the model number of the garage door opener. If you are calling about a Troubleshooting issue, it is recommended that you have access to your garage door opener while calling. If you are ordering a repair part please have the following information: part number, part name, and model number. 42

43 Notes 43

44 114A4912B Wi-Fi is a registered trademark of Wi-Fi Alliance. App Store is a service mark of Apple Inc. Google Play is a trademark of Google Inc. 2016, LiftMaster All Rights Reserved