ALLDATA Online Cadillac DeVille V8-4.6L VIN Y - Lower Crankcase Installation. Lower Crankcase Installation
|
|
- Rose Patterson
- 5 years ago
- Views:
Transcription
1 Page 1 of 7 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1998 Cadillac DeVille V8-4.6L VIN Y Conversion Calculator Vehicle Level Engine, Cooling and Exhaust Engine Service and Repair Engine Overhaul (Unit Repair) Lower Crankcase Installation Lower Crankcase Installation Notes Tools Required J Torque Angle Meter 1. Wipe all sealing surfaces clean with a dry, lint-free cloth. 2. Work the upper-to-lower crankcase seal into its groove starting at both ends and working the seal towards the center. The seal must not be torn, nicked, or out of the groove over its entire length on both sides of the crankcase.
2 Page 2 of 7 3. Apply a thin bead (2) of Gasket Maker, GM P/N or equivalent, to the upper crankcase. The bead should run parallel to the silicone seal (1) and through the centerline of the bolt holes but not through the bolt holes. Starting from the front of the block, the bead should be about 1 mm thick until the first bolt hole. Expand to mm thick from the first to the third bolt hole. After the third bolt hole the bead should be reduced to 1 mm until running off the end of the crankcase. Do not continue the bead all the way to the rear crankshaft seal. 4. Align the lower crankcase with the dowel pins in the upper crankcase. 5. Install the lower crankcase onto the upper crankcase slowly until feeling a positive stop. 6. Inspect the upper-to-lower crankcase joint in order to make sure the lower crankcase is fully seated on the cylinder block.
3 Page 3 of 7 7. Install the oil manifold plate. 8. Install the oil manifold plate retaining bolts. Tighten the oil manifold plate bolts to 10 Nm (89 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions. 9. Place the crankshaft oil scraper in position on the oil manifold. Align the holes with the main bearing bolt holes. 10. Install the main bearing bolts. The single stud-head bolt (1) used for oil pump pick-up mounting goes in the inboard position of the third set of main bearing bolts from the front of the engine.
4 Page 4 of Install the left side upper-to-lower crankcase perimeter bolts. 12. Install the right side upper-to-lower crankcase perimeter bolts.
5 Page 5 of Install the lower crankcase bolts First Pass Tighten the lower crankcase bolts (numbers 1 through 20) to 20 Nm (15 ft. lbs.) in the proper sequence Final Pass Tighten the lower crankcase bolts (numbers 1 through 20) an additional 65 in the proper sequence using the J Tighten the upper-to-lower crankcase perimeter bolts (numbers 21 through 28). Tighten the upper-to-lower crankcase perimeter bolts (numbers 21 through 28) to 30 Nm (22 ft. lbs.).
6 Page 6 of Lubricate the silicone seal in the oil manifold plate. With a twisting motion, install the end of the oil pump pick-up tube (1). 16. Install the oil pump pick-up retaining bolt (3) and nut (2). Tighten the oil pump pick-up tube nut to24 Nm (18 ft. lbs.). Tighten the oil pump pick-up tube bolt to 10 Nm (89 inch lbs.). 17. Install the two crankshaft position sensors (1). Tighten the crankshaft position sensor retaining bolts to 10 Nm (89 inch lbs.). 18. Rotate the crankshaft until the number one piston is at Top Dead Center (TDC) and the crankshaft key way is approximately at the 7 o'clock position.
7 Page 7 of Place the transaxle brace (1) in position on the cylinder block. 20. Install the transaxle brace retaining bolts. Tighten the transaxle brace retaining bolts to 50 Nm (37 ft. lbs.) 2010 ALLDATA LLC. All rights reserved. Terms of Use
Vehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationALLDATA Online Hummer H2 V8-6.0L - Brake Pads Replacement - Rear. Brake Pads Replacement - Rear
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Hummer H2 V8-6.0L Conversion Calculator Vehicle Level Brakes
More informationALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair
ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationAR05.20-P-6020AU Set the Basic Position of Camshafts
1 of 6 4/9/2008 9:57 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1999 Mercedes Benz E 320 4MATIC Sedan (210.082) V6-3.2L
More informationLocations. Select Vehicle New TSBs Technician's Reference Isuzu Truck Rodeo LS 2WD V6-3.2L
1 of 4 5/16/2008 1:06 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2001 Isuzu Truck Rodeo LS 2WD V6-3.2L Conversion Calculator
More informationHeater/Vent Module Replacement
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Conversion
More informationRemoval and Replacement
Page 1 of 10 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Suzuki Forenza L4-2.0L Conversion Calculator
More informationALLDATA Online Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K - Steeri... Steering Column
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K Conversion Calculator
More informationService and Repair. Fig. 1 Starter Motor Replacement
Motor / ALLDATA Online - 1995 Pontiac Firebird V6-204 4L VIN S... http://www.motoralldata.com/alldata/motor~v71595976~c21288~... 1 of 3 5/15/2008 10:45 PM Home Account Contact ALLDATA Log Out Help Select
More informationTesting and Inspection. Diagnostic Procedure Step 1-2
1 of 4 5/22/2008 7:54 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Nissan-Datsun Altima 2.5 S L4-2.5L (QR25DE) Vehicle
More informationALLDATA Online Chevy Truck TrailBlazer 2WD L6-4.2L VIN S - Service and R... Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Conversion Calculator
More informationService and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.
1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling
More informationALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
More informationALLDATA Online Lexus Truck RX 330 FWD V6-3.3L (3MZ-FE) - Headlight As... Page 1 of 10. Headlight Assembly. LH Headlamp Assy Part 1
ALLDATA Online - 2005 Lexus Truck RX 330 FWD V6-3.3L (3MZ-FE) - Headlight As... Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationFuel Injector Replacement (Right Bank) EN Injector Bore and Sleeve Cleaning Kit J Fuel Injector Removal Tool
Page 1 of 7 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Chevy Truck C 2500 Truck 2WD V8-6.6L DSL Turbo
More information2001 Chevrolet Corvette V8-5.7L VIN G
1 of 14 2/21/2013 10:34 AM 2001 Chevrolet Corvette V8-5.7L VIN G Vehicle» Engine, Cooling and Exhaust» Engine» Oil Pan» Service and Repair Oil Pan Replacement Removal Procedure 1. 2. 3. Remove the front
More informationService and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference
1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,
More informationALLDATA Online - 1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L - Servi... Page 1 of 22 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
More informationALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Transaxle Disassembly... Transaxle Disassembly and Reassembly
ALLDATA Online - 2002 Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Transaxle Disassembly... Page 1 of 21 Home Account Contact ALLDATA Log Out Help BEST FORD BEST FORD00001 Select Vehicle New TSBs Technician's
More informationValve Rocker Arm and Push Rod Installation (6.2L LS3)
9. Tighten the cylinder head bolts: 10.1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N m (22 lb ft). 10.2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence
More informationDISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY DISCONNECT CAM POSITION SENSOR CONNECTOR
1 of 12 4/26/2008 1:50 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1987 Toyota Supra L6-3.0L DOHC Turbo (7M-GTE) Conversion
More informationService and Repair REPLACING TIMING BELT/IDLER PULLEY/BELT TENSIONER. Special Tools:
1 of 9 6/18/2008 8:48 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1999 Volvo V70 XC AWD L5-2.4L Turbo VIN 56 B5254T Vehicle
More informationALLDATA Online Toyota Camry L4-2.4L (2AZ-FE) - Rear Strut Assembly. Rear Strut Assembly
Page 1 of 11 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Toyota Camry L4-2.4L (2AZ-FE) Conversion Calculator Vehicle
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
More informationA: Removing/Installing Camshaft
1 of 6 4/9/2008 9:39 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1995 Mercedes Benz E 320 Cabriolet (124 Chassis) L6-3199cc
More informationALLDATA Online Buick Regal V L VIN L SFI - HVAC Blower Motor -... HVAC Blower Motor - Noise/Vibration
Page 1 of 6 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1995 Buick Regal V6-231 3.8L VIN L SFI Conversion Calculator Vehicle
More informationDistributor: Service and Repair Distributor Replacement REMOVAL PROCEDURE
2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W Copyright 2007, ALLDATA 9.50 Page 1 Distributor: Service and Repair Distributor Replacement REMOVAL PROCEDURE NOTE: There are two procedures available
More informationEngine Removal and Installation
Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
More informationVehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair. Service and Repair
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Suzuki Verona L6-2.5L Conversion Calculator Vehicle
More informationALLDATA Online Mazda MX-5 Miata L4-1597cc 1.6L DOHC - Service and Rep... Service and Repair
Page 1 of 8 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1992 Mazda MX-5 Miata L4-1597cc 1.6L DOHC Conversion Calculator Vehicle
More informationCatalytic Converter: Service and Repair
2007 GMC Truck Envoy 4WD V8-5.3L Copyright 2009, ALLDATA 10.10 Page 1 Catalytic Converter: Service and Repair Catalytic Converter Replacement (5.3L and 6.0L Engines) Removal Procedure 1. Raise and suitably
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More information2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat.
31. Remove the 3 bolts, thermostat housing and thermostat. 32. Remove the 2 bolts, stud bolt and the A/C compressor. 33. Remove the bolt and the KS. 34. Remove the 8 bolts and the crankcase vent oil separator.
More informationAssembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
More informationCAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet
More informationRemoval Procedure. Remove the timing chain tensioner. 1 of 32 12/17/ :42 AM
1 of 32 12/17/2011 11:42 AM Removal Procedure 1. 2. 3. 4. 5. 6. Remove the camshaft cover. Raise and support the vehicle. Remove the No. 1 cylinder spark plug. Rotate the crankshaft in the engine rotational
More information8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
More information2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
More informationPart 1. CAUTION : Release established test pressure before beginning the next test step.
1 of 16 4/29/2008 4:35 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1998 Mercedes Benz SL 500 (129.067) V8-5.0L (119.982)
More informationALLDATA Online Buick Truck Rendezvous V6-3.4L VIN E - Draining and Fillin... Draining and Filling Cooling System
Page 1 of 8 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Buick Truck Rendezvous V6-3.4L VIN E Conversion Calculator Vehicle
More informationALLDATA Online Dodge Truck RAM 1500 Truck 4WD V8-5.7L - Service and R... Page 1 of 10. Service and Repair
ALLDATA Online - 2009 Dodge Truck RAM 1500 Truck 4WD V8-5.7L - Service and R... Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationFT - Function Test. Figure 1
1 of 6 4/8/2008 1:57 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1995 Mercedes Benz SL 500 (129.067) V8-5.0L (119.972)
More informationEngine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
More informationVehicle Level Engine, Cooling and Exhaust Cooling System Water Pump Service and Repair Removal. Removal
1 of 7 4/5/2008 11:18 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1994 Jeep Truck Wrangler L6-242 4.0L VIN S MFI Conversion
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More informationTurbo Boost Pressure Test
1 of 3 6/16/2008 9:07 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1992 Volvo 740 L4-2320cc 2.3L SOHC Turbo VIN 87 B230FT
More informationRemoval & Installation of Hydraulic Cylinder For Soft Top Bow
1 of 4 4/29/2008 9:59 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1997 Mercedes Benz SL 500 (129.067) V8-5.0L (119.982)
More informationService and Repair. NOTE: Before proceeding, review all Steering Column and Airbag Warnings and Cautions.
ALLDATA Online - 2003 Chrysler Truck Town & Country V6-3.8L VIN L - Service and... Page 1 of 10 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More informationRemoving and Installing Battery
ALLDATA Online - 2005 Porsche 911 GT3 (996) F6-3.6L - Removing and Installing Bat... Page 1 of 13 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's
More informationEngine Oil Leak at Crankshaft Rear Main Oil Seal (Replace with Revised Crankshaft Rear Main Oil
Document ID# 1706007 2004 Cadillac CTS Engine Oil Leak at Crankshaft Rear Main Oil Seal (Replace with Revised Crankshaft Rear Main Oil Seal) #05-06-01-019A - (Sep 22, 2005) Engine Oil Leak at Crankshaft
More information1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
More informationTiming Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
More informationASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More informationService and Repair. Material. Timing chain
ALLDATA Online - 1999 Mercury Cougar V6-153 2.5L DOHC VIN L SFI - Service and... Page 1 of 16 Service and Repair Notes Material Timing chain 1. Remove and discard the camshaft seal. 2. Remove the engine
More information2005 Cadillac CTS BRAKES Disc Brakes - CTS
Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid
More informationInstallation Instructions & Information
VP44 Installation Instructions & Information VP44 Pump General Information The fuel injection pump (VP44) is an electronic rotary distributor pump. The pump performs four basic functions: 1. 2. 3. 4. Producing
More informationOil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More informationTiming Chain Replacement and Riveting. Numbers in parentheses ( ) indicate a component or tool in the associated illustration.
1 of 5 4/9/2008 6:41 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1995 Mercedes Benz E 320 Cabriolet (124 Chassis) L6-3199cc
More informationALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front
Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle
More information1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder
Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection
More information2005 Cadillac CTS BRAKES Disc Brakes - CTS
Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid
More information2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
More informationA/T - 4T65E Harsh Shifts/Shudders/Slips/DTC's Set
Page 1 of 5 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 2000 Pontiac Bonneville V6-3.8L VIN K Conversion
More informationCAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
More informationSMU - Revised Timing Chain, Sprockets, Tensioner Installation Procedure # (Feb 9, 2000)
1998 Pontiac Grand Am SMU - Revised Timing Chain, Sprockets, Tensioner Installation Procedure #00-06-01-002 - (Feb 9, 2000) Revised Timing Chain, Sprockets, Tensioner Installation Procedure 1998-1999 Chevrolet
More informationfile://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More information2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
More informationALLDATA Online Honda Civic DX Sedan L4-1668cc 1.7L SOHC MFI - Remova... Removal and Replacement
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Honda Civic DX Sedan L4-1668cc 1.7L SOHC MFI Conversion Calculator
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More information1 of 5 1/10/2017 5:10 PM
1 of 5 1/10/2017 5:10 PM Shock Module Yoke Replacement ^ Tools Required - J 24319-B Steering Linkage and Tie Rod Puller Removal Procedure 1. Raise and support the vehicle. Refer to Vehicle Lifting. 2.
More information3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]
1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove
More informationService Bulletin
Service Bulletin 12-087 Applies To: See VEHICLES AFFECTED August 17, 2013 2008 11 Accord L4: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-087, dated April 30, 2013,
More informationService Bulletin TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption
Applies To: 2009 10 TSX L4 with M/T ALL Service Bulletin 13-006 February 22, 2013 2009 10 TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption SYMPTOM The engine oil level is low on the
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More informationPage 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
More information2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension.
2011 > G 1.6 DOHC > Language Removal Engine removal is not required for this procedure. 1. Disconnect the battery negative terminal. 2. Loosen the water pump pulley bolt and the drive idler mounting bolt.
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationPiston diameter should be measured at normal room temperature of 70 F (21 C).
Piston & Rod Assembly 1. Pistons are not interchangeable from bank to bank. Pistons are marked L and R (left and right) and must be installed with arrow on top of piston pointing toward front of engine.
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More information1 of 15 1/26/2017 8:57 AM
1 of 15 1/26/2017 8:57 AM Timing Belt and Balancer Belt Removal Special Tools Required ^ Holder Handle 07JAB-001020A ^ Holder Attachment, 50 mm, Offset 07MAB-PY3010A ^ Socket, 19 mm 07JAA-001020A or a
More information2004 Chevy Truck Silverado WD V6-4.3L VIN X
1 of 14 10/17/2013 8:32 PM 2004 Chevy Truck Silverado 1500 2WD V6-4.3L VIN X Vehicle» Powertrain Management» Ignition System» Distributor» Service and Repair» Distributor Replacement DISTRIBUTOR REPLACEMENT
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More informationPage 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required
More information2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
More informationDiagnostic Trouble Code (DTC) Information
1 of 3 7/20/2008 8:35 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1999 Mercedes Benz Truck ML 430 (163.172) V8-4.3L (113.942)
More informationNOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
More informationALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Input Shaft. Input Shaft
Page 1 of 16 Home Account Contact ALLDATA Log Out Help BEST FORD BEST FORD00001 Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI Conversion
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More informationService Bulletin
Service Bulletin 12-089 Applies To: See VEHICLES AFFECTED April 30, 2013 2010 CR-V: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-089, dated April 3, 2013, to revise
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More informationCylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
More informationTruckmount Repairs Cat 290 Pump Repair
Cat 290 Pump Repair COMMON STOCKED PARTS 3 PST101802 Cylinder CAT 290 3 PST26112 Cylinder CAT 280 1 PHY027-004 Oil Filler Cap Black (old 280 & 290 s) 1 PST43211 Oil Filler Cap - Red 1 PST14177 O-ring Oil
More information