The TR8 TPS (Throttle Potentiometer Switch ERC 3619 NLA)
|
|
- Lambert Simon
- 5 years ago
- Views:
Transcription
1 The TR8 TPS (Throttle Potentiometer Switch ERC 3619 NLA) My TR8 Efi had been running odd for some time with on occasions a very strong HC smell. Unfortunately with its MOT looming it was fairly obvious it wasn t going to pass so I was going to have to do something about it. Strange how when a cars performance and driveability slowly deteriorates over time you tend to instinctively live with it. In this case driving the car was becoming increasingly less pleasurable with often a jerky ride and fuel consumption becoming horrendous. The heavy rains here in Yorkshire seemed to make the issue worse having driven back from Manchester on the worst day of the rains. I d previously moded my TR8 to run with a piggy back ecu to improve its performance so I decided to take the car back to Denis Vessey who did the mod to put it on his rolling road. It took less than 20 mins to see the fuel was all over the place and then another two to find that when you moved the TPS (Throttle Potentiometer Switch) plug it all changed. That immediately pointed to either a faulty plug or the TPS its self. Changing the plug didn t fix it so we were left with the TPS which is now no longer available. Two options then remaining; take it apart and try and fix it, or try and find a new TPS that would fit in its place. We tried option one first. The top of the TPS has been sealed where the screws are so we carefully drilled out the plastic sealant as it s a quite hard material. Then the screws can be easily undone.
2 What you see next when the two parts come apart are the carbon tracks that the wiper arm moves over to indicate to the ECU what position the accelerator is in. You ll note from this picture we found that the carbon tracks had in effect almost worn through the carbon. This isn t always the end of the story as it s possible to remove the plastic welds on the wiper arm and move it to a new piece of carbon using small screws to re-secure it. See picture below. Unfortunately in this case the RED wire we discovered after cutting through the plastic sleeve was in fact only hanging on by a thread. We had a go at re-soldering it to the remaining stub and sealing it all back up with some sealant but in this case once back on the rolling road it wasn t successful.
3 So to plan B Denis has a motor sport TPS that he uses as a generic replace all sort of part made by Lumenition part number TPS001. Main problem is that the spindle holder is set recessed as opposed to the original TPS spindle holder that sticks out (See picture below) and the TR8 adaptor plate is modified for this with a raised circle platform. So two choices here make a new adaptor plate or machine the original to fit the new. Given I had a spare anyway we machined the original down by 4 millimetres off the face (not including the raised platform that fits in the circle recess you can see above which was removed prior). Two new adjustment screw holes need to be tapped plus one cable holder screw hole as well. Point to note when modifying the original plate is that it s actually two metals, aluminium and a steel circle in the centre. The wires are exactly the same as the original RED, YELLOW and GREEN.
4 So all you have to do is to fit the new style plug to the harness. The spindle is a very tight fit so to avoid breaking the new spindle holder you will need to gently file a very small amount off to make a snug fit as opposed to a tight never get it off again fit. See Picture below. Notice it s about 2/3rds the size of the original!
5 Once back on the road WOW what an improvement very very responsive now a totally different car to drive very very smooth! Nice neat fit and works so much better than the original! Richard Connew. World Wide TR7 TR8 Owners Club
My Hawk build Part 8 by Stuart Clarke
My Hawk build Part 8 by Stuart Clarke Front hubs, brakes and brake lines. There was still no news on my rear springs so I thought I d find something else to get on with. I had the front hubs, brake calipers
More informationRostra Electronic Cruise Control Install On a Stratoliner or Roadliner
Rostra Electronic Cruise Control Install On a Stratoliner or Roadliner MATERIALS LIST: 1 - Rostra Part # 250-1223 (www.brandondist.com/products/cruise1223.htm) 1 - Signal Splitter part # 250-4369 1 - Engagement
More informationTip: LED Lighting for the 3098 Locomotive and 4392 Coach Set Date: , ,
Hi All, Over the past few months I have been working at a steady pace to install LED lighting in my passenger coaches. The coach lighting must have LED lights to reduce power consumption on the layout
More informationMGB V8 Roadster restoration project Report 128
20th March 2017. Sorry to keep you in suspenders between report 127 and report 128, with regards to the indicator stalk switch. INDICATOR & HORN STALK SWITCH - continued After removing all the internal
More informationFitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE
Fitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE Before I describe how I did this, I must first thank other members of the Disco3.co.uk forum (namely J,moore
More information4TH GEN SEATS IN A 3RD GEN TRUCK
4TH GEN SEATS IN A 3RD GEN TRUCK by Flopster843 02 Oct 2016 If you drive a 3rd generation Dodge Ram truck, I am sure you have discovered that the OEM seats are not the greatest (Figure 1.) They are extremely
More informationMID-MOTOR EBIKE KITS: INFORMATION FOR INSTALLERS
MID-MOTOR EBIKE KITS: INFORMATION FOR INSTALLERS Tips for evaluating bikes for conversion Consider the age, condition and value of the bike. Is it worthwhile using it as a donor? For reference, a good
More informationAir Compressor/Water Pump III - Making the Steam Valves
Page 1 of 14 Air Compressor/Water Pump Part III Making the Steam Valves Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 1/09/04 Last Revised: 0 The cylinders pistons and water valves were completed
More informationTroubleshooting Guide for Dewert Systems
Troubleshooting Guide for Dewert Systems Dewert electronics aren t as common as Okin systems as they re mainly used by one manufacturer (Pride). However, Pride is the largest lift chair manufacturer in
More informationTriumph Street Triple VSM Grip Heater Install
Triumph Street Triple VSM Grip Heater Install Introduction: With winter fast approaching and with painful memories of last winter riding with the club it was time to do something about getting some grip
More informationSmart Opener Retrofit by Richard Bevan (bimmerfest riku2)
Smart Opener Retrofit by Richard Bevan (bimmerfest riku2) Document history V 1.0 02.04.2015 Document created. Introduction This document tells how to retrofit the smart opener to a 2011 BMW 5 series (F10).
More informationPYRTE. Building The Front Axle, Fork and Steering
PYRTE Building The Front Axle, Fork and Steering The front axle on this traction engine is a very simple affair, in that it is a rectangular steel rod, sat on edge, with a pivot in the centre, which is
More informationESS INSTALL. The donor car /6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9
ESS INSTALL The donor car.. 1997 540/6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9 The install went in several stages. Disconnect the battery Stage 1 Remove
More informationTip: Axle Bearing Replacement Date:
Hi All, Some time ago I came into possession of some Donnerbüchsen or Thunder Boxes, Märklin items 4313,4314 and 4315 which were no longer usable as the axle bearings had worn out causing the wheels to
More informationMy Hawk build part 24 by Stuart Clarke. Getting ready to turn the key.
My Hawk build part 24 by Stuart Clarke Getting ready to turn the key. Things had moved on quite nicely now and the end was virtually in sight. It was getting to that do or die moment when I find out if
More informationWiring Harness Relocation by Flopster Mar 2012
Wiring Harness Relocation by Flopster843 21 Mar 2012 On my 2008 Ram, there is a gigantic blob of electrical wiring that Dodge decided to put between the engine and the brake master cylinder, just behind
More informationLooking up the front of the engine from under the radiator. (Picture taken with belt under tension.)
8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationTRIUMPH ST ROSTRA ELECTORNIC CRUISE CONTROL
TRIUMPH ST 1050 - ROSTRA ELECTORNIC CRUISE CONTROL There have been a number of threads discussing the pros and cons of electronic vs throttle lock cruise controls. Living in Texas can require some long
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationb o o s t r e t a i n e r v a l v e
b o o s t r e t a i n e r v a l v e i n s t a l l a t i o n i n s t r u c t i o n s For questions or tech support, CONTACT US! Email: greg@hiperformancestore.com sales@hpsimotorsports.com Sites: www.hiperformancestore-fiat.com
More informationBrake master cylinder replacement
Brake master cylinder replacement 8-25-2010 I had replaced the front brake master cylinder a few years ago when it developed a bad leak, at that time, I ordered a new master cylinder from Spartan, very
More informationAttached Images. Attached Images
Results from May 9 th : I'm sorry to say... I should have stayed home!.. Well, actually I'm glad I went, but the day was NOT a success from a competitive standpoint. It's always risky to take an untested
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More informationSteelmate TP-90 Review July 2016 OVERVIEW I needed a TPMS (Tire Pressure Monitoring System) to monitor the tires on my LeesureLite trailer. I have an existing TPMS system on it however the monitoring device
More informationTools & Parts I Used. Here's everything that comes with the kit.
Ford Super Duty Power Tailgate Lock Install 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page This page describes the steps to install the Pop & Lock PL8250 power tailgate lock kit. This kit
More informationREPAIR for: Sidelamp Bulb(s) Faulty, Left Tail Lamp Faulty, Right Tail Lamp Faulty, Directional Indicator Faulty, Left Hand Stop Bulb Faulty
REPAIR for: Sidelamp Bulb(s) Faulty, Left Tail Lamp Faulty, Right Tail Lamp Faulty, Directional Indicator Faulty, Left Hand Stop Bulb Faulty DIFFICULTY LEVEL: ***** Drilling, Wire Crimping, Tight Spaces,
More informationMikuni RS Carburetor Conversion
Mikuni RS Carburetor Conversion After putting your carbies on the bench or the kitchen table if the wife is out, you will see that the linkages may be in different positions depending on which brand of
More informationINSTALLATION OF A WARN M8000 WINCH IN A HIDDEN MOUNT ON THE 2001 EXPLORER SPORT TRAC
INSTALLATION OF A WARN M8000 WINCH IN A HIDDEN MOUNT ON THE 2001 EXPLORER SPORT TRAC By: Kyle Schwulst Email: bigmellon@yahoo.com BACKGROUND I have always wanted a winch on my vehicle. There is just something
More informationWhy I like the IRC GP110 Tire on a KLR
Why I like the IRC GP110 Tire on a KLR I know, I know, discussing tires is like discussing oil or chain lube. It always fires up the crowd. We all have opinions and here are the reasons that I like the
More informationHidden Savings in Modern Manufacturing
JARVIS CUTTING TOOLS CAPABILITIES Hidden Savings in Modern Manufacturing Five lessons from companies that found millions in hidden savings through simple, previously-overlooked changes to their manufacturing
More informationBMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
More informationS1 Sequential. T56 Magnum. Sequential shifter. Contents and assembly instructions
S1 Sequential Sequential shifter T56 Magnum Contents and assembly instructions Parts List Sequential shifter x1 Base plate x1 Base spacer x1 Drill Square x1 Shaft fitting x1 Square washer x1 8mm Aluminium
More informationUsing your Digital Multimeter
Using your Digital Multimeter The multimeter is a precision instrument and must be used correctly. The rotary switch should not be turned unnecessarily. To measure Volts, Milliamps or resistance, the black
More informationONYX VALVE CO MODEL CHR & CHP Installation & Maintenance
ONYX VALVE CO MODEL CHR & CHP Installation & Maintenance OPERATION: (05-011) The Onyx series CHR and CHP are hand operated pinch valves. A simple hand-operated mechanism drives a direct acting pinch bar
More informationREAR STEEL BUMPER INSTALLATION INSTRUCTIONS Runner
REAR STEEL BUMPER INSTALLATION INSTRUCTIONS 2010+ 4Runner Version 2.1.0 - September 2016 Thank you for purchasing the Southern Style OffRoad Toyota 4Runner 5 th Gen Modular Rear Plate Steel Bumper. It
More informationShay Steam Brake Valve
Shay Steam Brake Valve Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 10/26/2003 Last Revised: 06/05/2004 Update 10/28/2003: The day after I published this page Mike Green from up in Ontario emailed
More informationCHECKING THE ELECTRONIC FUEL INJECTION SYSTEM.
CHECKING THE ELECTRONIC FUEL INJECTION SYSTEM. IMPORTANT:- No checks can be carried out without the use of the Special Bosch EF AW 220 Test Unit, which enables every part of the Electronic Fuel Injection
More informationMGB V8 Roadster restoration project Report 130
1 st April 2017. I promise I won t add in any April Fool jokes into this report. But of course anything is possible! Yesterday, I only managed an hour on the MG, as I helped Jaymic with their stock take.
More informationSW20 Coolant System Maintenance.
SW20 Coolant System Maintenance. This article contains information on how to change and bleed the coolant, as well as flushing the system. It is based on information in the service manual, tips gathered
More information13 October, 2014 Page 1
13 October, 2014 In my second and last Helicycle I want to make everything better than the first one. That includes not only a transmission chip detector, but one for the tail rotor as well. The transmission
More informationMGB V8 Roadster restoration project Report 67
19th August 2016. This report jumps a bit from one subject to another. If I need to put some thought into a certain aspect of the rebuild I tend to get on with another job and sleep on the problem until
More informationNISSAN FIGARO NIGGLES PART 4 I CAN T SEEM TO FIND NEW TYRES FOR MY FIGARO
NISSAN FIGARO NIGGLES PART 4 I CAN T SEEM TO FIND NEW TYRES FOR MY FIGARO There were two sizes of tyres fitted to the Figaro originally: 155SR12 or 165 70 12. Don t mix these sizes on the car all four
More informationAir Compressor/Water Pump IV - Pilot Valve Stem, Test & Installation
Page 1 of 8 Air Compressor/Water Pump Part IV Pilot Valve Stem, Test & Installation Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 1/13/04 Last Revised: 0 Valve Test: I decided to test the steam valves
More informationMGB V8 Roadster restoration project Report 86
2 nd November 2016. There seems to be so much to do, odds and ends to order, not enough space to do stuff. This morning I think I better start writing down a list of things to do that are easier while
More informationTroubleshooting Guide for Limoss Systems
Troubleshooting Guide for Limoss Systems NOTE: Limoss is a manufacturer and importer of linear actuators (motors) hand controls, power supplies, and cables for motion furniture. They are quickly becoming
More informationBendix Hydroboost Repair
Bendix Hydroboost Repair Report this image Pic 1 the leaky power piston seal... (probably master cyl too.) Pic 2 PS fluid after spider removal and MC actuator rod Pic 3 Removing the accumulator (note 1/8
More informationDisconnect the negative battery cable!
Understanding Mod-3 on a C90 With Wiring Diagrams By DrJones18LC I do not have a C90 at my disposal (or audio/video equipment for that matter) so I can't make a live step by step how-to on doing Mod-3.
More informationMGB V8 Roadster restoration project Report 138
24th May 2017. FITTING THE CARPETS - continued I have included quite a lot of detail and photographs on the carpet and trim fitting, as it may help those who decide to do this job on their own car. The
More informationTip: LED Lighting for the 4367 SBB Euro City Set, 4366 and 4368 Cars Date: , Corrections Modified , Photos
Hi All, I have had the 4367 SBB Euro City set with extra cars 4366 and 4368 since 1998, apart from a test run on the layout they have stayed in storage ever since. I decided to change some rolling stock
More informationPeugeot 406 Coupe: Delocking your boot V.1 April 2005
This is a first stab at a DIY guide to de-locking your 406 Coupe. It isn t a hard modification to do yourself, but you do need to be confident working on your cars electrics and removing and refitting
More informationTip: 3652 and 3756 Crocodiles with LP4.0 and LED Lighting Date:
Hi All, My friend Adrian asked me to convert two crocodiles 3652 and 3756 using LokPilot 4.0 decoders. Adrian wanted to run both locomotives as a double headed configuration so this would require that
More informationTONY S TECH REPORT. Basic Training
TONY S TECH REPORT (Great Articles! Collect Them All! Trade them with your friends!) Basic Training OK YOU MAGGOTS!! Line up, shut up, and listen good. I don t want any of you gettin killed because you
More informationMAIN ROTOR TRANSMISSION CHIP DETECTOR
MAIN ROTOR TRANSMISSION CHIP DETECTOR 13 October, 2014 In my second and last Helicycle I want to make everything better than the first one. That includes not only a transmission chip detector, but one
More informationUB2. ZENA Universal Power Generator Mounting Bracket Assy. General Recommendations for Field Use
UB2 I N C O R P O R A T E D 330 Club Springs Road Elmwood, Tennessee 38560 Phone: (615) 897-2011 Fax: (615) 897-2023 Internet: www.zena.net ZENA Universal Power Generator Mounting Bracket Assy. General
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationMemories of a Power Brakes conversion on a 1971 Corvette
Memories of a Power Brakes conversion on a 1971 Corvette I did the job all by myself, except for the brake bleeding. Looks like an easy job but its not, you definitely need some experience to avoid screw
More informationMGB V8 Roadster restoration project Report 159
29th July 2017. MG DRIVES OUT OF THE GARAGE FOR THE FIRST TIME. I started my reports on the 15 th January 2015 when I pushed the Yellow Peril into the workshop. Little did I realise that it would be this
More informationPlumbing Part VI - Blowdown Valve Nelson Riedel Initial: 9/28/03 Last Revised: 04/24/2006
Page 1 of 8 Plumbing Part VI - Blowdown Valve Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 9/28/03 Last Revised: 0 When I started to think about the blowdown I realized that I'd never seen the actual
More informationDodge Ram 09-Current CS-DTR SERIES BACKUP CAMERA INSTALLATION
Dodge Ram 09-Current CS-DTR SERIES BACKUP CAMERA INSTALLATION Thank you for your purchase! These instructions cannot possibly cover every option group for every model year of RAM trucks so you may find
More informationLJ20 Distributor - Disassembly Inspection Repair
LJ20 Distributor - Disassembly Inspection Repair Old Codger New To Old Suzuki Jeeps The odometer on this 1972 LJ20 indicated the distributor had less than 10,000 miles of wear but during that time it had
More informationCanems Engine Management Solutions. +44 (0) Scotter Road Scunthorpe DN15 7EH UK
DRH Performance ECU Porsche 911 3.2 MAP sensor conversion kit Kit Contents A) 1 x Green Filters cotton gauze air filter B) 1 x Air intake pipe / air temperature sensor C) 1 x MAP sensor D) 1 x CNC MAP
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationTip: and Orient Express LED Light Upgrade Date: Correction
Hi All, I have since inherited my friend Rudolf s 42755 Orient Express with the extra 42760 car set and wanted to complete the LED light upgrade as we had planned. Side view of the Restaurant car with
More information*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.
www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not
More informationHasse Mods for the Ampeg J20 Guitar Amp
Hasse Mods for the Ampeg J20 Guitar Amp The following is adapted from a post I put up on The Gear Page, in the Amp Techincal forum. It shows the mods I did to my Ampeg J20. Okay, here s my mods for this
More informationSunFlower Helicopter Rocket LUNAR Build Session: 9/25/08 By Tom Desmarais
SunFlower Helicopter Rocket LUNAR Build Session: 9/25/08 By Tom Desmarais Contents of Kit: A. 3 1/16 x1 x11 basswood rotors B. 3 1/16 x2 x2 basswood fins C. 3 1/16 x5/16 x1/2 basswood hold spacer D. 3
More informationArrow Shark 2013 Outboard Dragon Drive Owner Manual. Introduction
Arrow Shark 2013 Outboard Dragon Drive Owner Manual Introduction Our purpose in designing the Dragon Drive is to offer a high quality, sleek looking and durable outboard drive for the growing RC F1 (Formula
More informationInternal battery 1.5AH Li-ion battery placed in battery holder
Elecraft KX1 HT By, Edward R. Breneiser, WA3WSJ I love to hike the AT and activate SOTA Summits. I built my Elecraft KX1 and have used it for hiking, but the idea came to me to use it as an HT. I could
More informationPart # C-10 Level 1 Air Suspension System
350 S. St. Charles St. Jasper, In. 47546 Part # 11330199 63-72 C-10 Level 1 Air Suspension System Front Components: 1 11331099 Front CoolRide Kit for Stock Lower Arms 1 11330509 RQ Series Front Shock Kit
More informationPage1. ISF Stainless Steel Headers // Part# HDR-004
Congratulations on the purchase of your ISF Stainless Steel Headers and thank you for choosing Sikky Manufacturing. This installation manual is intended to guide you through the removal of the factory
More informationWH Ford 2WD Steering System #2013/2015 Date 02/15/04 rev. 1
Phone (209) 400-7200 Fax (209) 943-7923 www.wildhorses4x4.com WH Ford 2WD Steering System #2013/2015 Date 02/15/04 rev. 1 Basic system notes: This system works on 1966-1977 Broncos with manual steering
More informationThe information below was obtained from measurements made on five cylinder heads in December 2001.
Bristol Austin 7 Club - technical article www.ba7c.org The majority of these tips have appeared in club newsletters over the years. Please note that you use them at your own risk as neither the Bristol
More information"Everyone who builds a DIY project has their own set of goals and constraints which they work with."
racesim BUILD K E Y F E AT U R E S Named "MRAP Seatmover" Made almost entirely from MDF, Rope And Pulleys Uses common materials and no special tools required 3 rd DOF for traction loss easily added Electronics
More informationRear Girling Shock Absorber Renewal
Rear Girling Shock Absorber Renewal Larry Shoer, Massachusetts, USA, larryshoer@comcast.net Posted 19 July 2004 at 02:13:14 UK time This spring I renewed the rear Girling shock absorbers on my MG TD. I
More informationTroubleshooting Guide for Okin Systems
Troubleshooting Guide for Okin Systems More lift chair manufacturers use the Okin electronics system than any other system today, mainly because they re quiet running and usually very dependable. There
More informationHow to replace or adjust the altitude clutch of the NexStar N11GPS
Langenbrettach/Germany, February 10 th 2004 Matthias Bopp How to replace or adjust the altitude clutch of the NexStar N11GPS Table of content How to replace or adjust the altitude clutch of the NexStar
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationSpecialist Components. SPi 5 Port EFI Kit
Specialist Components SPi 5 Port EFI Kit Version 1.1 Sept 2012 Congratulations on the purchase of your SPi 5 port EFI Kit! Kit Content:- Alloy inlet manifold gasflowed to suit 45/50mm throttle body Injector
More informationRenovering af vinkelgear
Renovering af vinkelgear Angle-Drive for the Speedo a simple part but a real nuisance During the evolution from the TR4 to the TR4A a number of changes were made, that didn't work very well in the long
More informationCabin Light. Hi All, 1
Hi All, My friend Rudolf set me a challenge for his 36331 electric locomotive, wanting Telex couplers fitted. When I opened up the locomotive I discovered there is very little room to add extra components
More informationTotal installation time for the cruise control was approximately 8 hours.
The following summary highlights the start-to-finish install of an Audiovox cruise control on stellarpod s (Steve) ST1300. Fred D (Fred) and ChucksKLRST (Chuck) primarily performed the install (Steve did
More informationThank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible
More informationSteering Damper for FLH Harley-Davidson Bikes/Trikes
Steering Damper for FLH Harley-Davidson Bikes/Trikes I have spoken with several HD Touring model trikers, who are looking for increased feel in the steering department. Some want to cure a slight wobble
More informationYamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions
OFTRacing.com Email Scott Moto 2006-2011 Yamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions Included Parts: 1 Moto-r Kill wiring harness including Pro Armor tether switch, Jacobsen
More information100E into E83W will go (just)
100E into E83W will go (just) (The story of how Noddy, an E83W pick-up, received a 100E engine) After much blood sweat and tears Noddy s heart transplant has been successfully carried out, he is now powered
More informationStep 1: Preparing the rear end of the car for the trailing arm replacement.
Introduction to the Trailing Arm Replacement Procedure I had been noticing some strange behaviour in my 1979 Corvette for at least a year or so. It is difficult to describe but the rear end felt loose,
More informationInstalling AMP-wiring in a New Beetle
Installing AMP-wiring in a New Beetle Vehicle used: New Beetle 2.0i Type 9C (1999) Used set of cables: Dietz 35mm² power cable, double shielded Dietz chinch cable ( 35mm² Professional Line ) First of all:
More informationSteeda Sport Mustang Lowering Springs (2005+) - Installation Instructions
Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions The below installation instructions work for the following products: Steeda Sport Mustang Lowering Springs (2005+) Please read
More informationSelf-Concept. The total picture a person has of him/herself. It is a combination of:
SELF CONCEPT Self-Concept The total picture a person has of him/herself. It is a combination of: traits values thoughts feelings that we have for ourselves (self-esteem) Self-Esteem Feelings you have for
More informationRebuilding the HE-120 Redrive
Rebuilding the HE-120 Redrive Rick Cavallaro Disclaimer: I am NOT an expert mechanic. If something looks or sounds wrong in these directions, it probably is. I d be happy to receive any tips or feedback
More informationWOT Box Installation Instructions VW / Audi
Connector Pinout Pin Color AWG Name WOT Box Installation Instructions VW / Audi Description 1 Yellow 18 RPM Connect to Fuel Injector Drive Signal or Ignition Control Signal (varies by car model) 2 Black
More informationInstructions for Assembling Driving Wheels, Axles and Crankpins
Instructions for Assembling Driving Wheels, Axles and Crankpins (Version 1; October 2008) Introduction These instructions explain how to assemble Exactoscale 4mm scale driving wheels, axles and crankpins
More informationShay Plumbing VIII - Steam Turret & Associated Plumbing
Shay Plumbing VIII - Steam Turret & Associated Plumbing Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 11/24/03 Last Revised: 06/06/2004 Note: This page has been revised several times to reflect advice
More informationDigifant Ignition Basics, Eurovan Or, what to look for if your 5 Cylinder Eurovan won t start due to no spark
Digifant Ignition Basics, 1992-96 Eurovan Or, what to look for if your 5 Cylinder Eurovan won t start due to no spark The story: In the spring of 2007, I started to have hard starting issues with my 93
More informationXRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS
XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS The use of NFU (No Further use) and REUSE (Re Use) relates to the individual parts storage when performing the upgrade. Also note that all
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationUltra-micro Yak-55 by Dynamic Foamy Review
Ultra-micro Yak-55 by Dynamic Foamy Review About myself: This is my first official review. Bert Wilson, from Dynamic Foamy was looking for somebody to review his latest kit offering, the micro Yak-55.
More informationInstallation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies
Installation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies Getting started with the removal of your existing Jeep body. Trust nothing to memory; take photos of everything at different
More information