Spring Bearing Rocker Replacement Installation [Kit # ] for Elevance Continental-Style Delivery Unit

Size: px
Start display at page:

Download "Spring Bearing Rocker Replacement Installation [Kit # ] for Elevance Continental-Style Delivery Unit"

Transcription

1 Spring Bearing Rocker Replacement Installation [Kit # ] for Elevance Continental-Style Delivery Unit Note Use this kit to replace one or more Spring Bearing Rockers in an Elevance Continental-Style Delivery. Applies to Models: Special Tools: none Language of origin: English Step 1: Identify Kit Components A) Familiarize yourself with the components you will be replacing. Note Right s are marked with RED. Bearing Rocker Left Right Spring Installed in Bearing Rocker Bearing Rocker Tower Assembly 2016 Midmark Corp. 60 Vista Drive Versailles, OH USA TP FO Rev A1 C2169 Rev. A (mm/yy)

2 Step 2: Remove lids and move tubing to access delivery unit. A) Turn off air and water using the Shut Offs in the J-Box. B) Unplug Power Supply from electrical mains in the J-Box. C) Turn Water Bottle counter-clockwise to release the air pressure in the water tubing. D) Remove Magnetic Lid. E) Remove two screws and lift off the Metal Cover. F) Slide tubing out of each arm roller and allow handpieces (not shown) to hang over the back of the unit. G) Push arm forward to access screw, remove it and pull up to remove the arm. Remove all arms. H) Pull handpiece tubing from tower indentation; leave Strain Relief on tubing. Magnetic Lid Metal Cover Arm Roller WARNING Always disconnect power from electrical mains before removing any covers. Failure to do so may result in personal injury. Water Bottle J-Box Strain Relief Shut Offs Electrical Mains 2

3 Step 3: Remove the Top Cover Assembly. A) Remove ten screws from the bottom, then lift and rotate the Top Cover Assembly forward. B) Unplug all wiring connections from the ICM (Integration Control Module ). Tip: Leave all tubing connected to the actuators. C) Remove two screws and lift out the first actuator. D) Rotate the actuator lever backwards. E) Turn the actuator counter-clockwise so that you can work the actuator free from the linkage for positions 1, 2 & 3. You will turn the actuator clockwise to work it free of the linkage for positions 4, 5 & 6. F) Remove all the actuators. ICM Top Cover Assembly 3

4 Step 4: Remove the Tower Assembly. A) Remove two screws from the bottom side of the Tower Assembly. B) Remove two screws from the top side of the Tower Assembly. C) Remove two screws from the Tower Assembly mount plate. D) Lift off the Tower Assembly with the Mount Plate. Tower Assembly Mount Plate 4

5 Step 5: Access the Spring Bearing Rockers. A) Rotate Tower Assembly 180 to access the screws on the bottom. Tip: Cut a 1-1/2 x 15 inch slot into a box and use to support the Tower Assembly as you work on the bottom of it. B) Make note of the Tension Adjustment for each position, then turn all screws to the LOW tension (screw fully IN) setting. (Use chart on the next page.) C) Remove 10 screws and the Mount Plate. D) Make note of which positions have linkages, then remove each one by rotating the Bearing Rocker until you can work the linkage free of it (See F.) E) Remove 8 screws and the tension plate (Only remove the Tension Plate on the side of the Bearing Rocker(s) you are replacing.) F) Remove and discard the Spring Bearing Rocker you are replacing. G) Repeat until all of the Spring Bearing Rockers are replaced. Tension Adjustment Mount Plate High (no groove is visible) Low (groove is visible) Tower Assembly Tension Plate Spring Bearing Rocker with (shown with linkage for reference) 5

6 Step 6: Reassemble the Tower with the new Spring Bearing Rockers in place. A) Reference Steps 5 through 3, working in reverse to reassemble the Tower Assembly with the new Spring Bearing Rockers in place. B) Be sure to return the linkages and adjust the tension at each handpiece position to their original settings. Place an X in the chart below to note high or low tension and or No for each handpiece position. Position High Tension Low Tension No Installation Tips: The Arm Mounting Screw Access should face the Strain Relief Cutout. Rotate the Spring Bearing Rocker a little to install linkages. Spring legs Strain Relief Cutout Arm mounting hole Arm Mounting Screw Access Spring legs Installation Tip: Spring legs must extend through the slots on the Tension Plate. Tension Plate Slots 6

7 Step 7: Replace Covers. A) Route handpiece tubing through each arm roller. B) Install zip ties below the Strain Reliefs to help keep handpieces aligned across the front of the unit. C) Install the Metal Cover back onto the unit with two screws. D) Install the Magnetic Cover back onto the unit. E) Make certain that the water bottle is pressurized (turned clockwise fully). F) Turn ON air and water Shut-Offs in the J-box. G) Plug the Power Supply into the electrical mains. H) Turn the Master Switch ON and pull each handpiece individually to verify operation. J-Box Keep Handpieces Aligned Zip Tie below Strain Relief 7

Cylinder Rod End Replacement Kit [ ]

Cylinder Rod End Replacement Kit [ ] Cylinder Rod End Replacement Kit [002-2068-00] Contents: Installation...1 Special Tools: none Language of origin: English Step 1: Inspect components. Step 2: Position chair. A) Move the back section to

More information

Product Name Chair Conversion Kit (to Console Delivery Unit) Installation [Kit # xx]

Product Name Chair Conversion Kit (to Console Delivery Unit) Installation [Kit # xx] Elevance Product Name Chair Conversion Kit (to Console Delivery Installation Unit) Installation [Kit #002-1965-xx] Attention: Use this kit to convert an Elevance Chair to a Chair with an Elevance Console

More information

Knee Crutches / Cladding [9A410 / 9A411 / 9A412 / 9A413]

Knee Crutches / Cladding [9A410 / 9A411 / 9A412 / 9A413] Knee Crutches / Cladding [9A40 / 9A4 / 9A42 / 9A43] Intended Use: To support patient s knees / legs during examinations. Requirements: 604 / 622 / 623 models require a special cladding kit to accommodate

More information

Master Slave Converter [ VAC & VAC]

Master Slave Converter [ VAC & VAC] Master Slave Converter [002-1590-00-115 VAC & 002-1590-01 230 VAC] Contents: Installation...1 Wire Diagram...4 Exploded View...6 Intended Use: To provide simultaneous operation of up to five Midmark compressors

More information

Side Delivery Unit Installation

Side Delivery Unit Installation Side Delivery Unit Installation CONTENTS Mounting Location... 1 Minimum Cabinet Size Requirements... 1 Mounting Requirements... 1 Regulator Installation... 2 Cabinet Mount Bracket Installation... 2 Wall

More information

Chexit/RCM/DE5300. Chexit/RCM/DE5300 Service Parts. Chexit Field Wiring Cable. DE5300/RCM Field Wiring Cable. Table of Contents

Chexit/RCM/DE5300. Chexit/RCM/DE5300 Service Parts. Chexit Field Wiring Cable. DE5300/RCM Field Wiring Cable. Table of Contents *941316-00* 941316-00 Service Parts Replacement Chexit/RCM/DE5300 Special Instructions Chexit Service Parts Chexit/RCM/DE5300 Service Parts Chexit Module Key Switch RX Switch Chexit Field Wiring Cable

More information

630 (-010 thru -013, -020 thru -023)

630 (-010 thru -013, -020 thru -023) 60 (-00 thru -0, -00 thru -0) Headrests Actuators: Back Tilt Foot Upholstery: Premium UltraPremium Controls: Corded Hand Ctrl Corded Foot Ctrl Wireless Fuses Product Overview Headlock Components Seat Section

More information

Product Name Chair Conversion Kit (to LR Delivery Unit) Installation [Kit # xx]

Product Name Chair Conversion Kit (to LR Delivery Unit) Installation [Kit # xx] Elevance Product Name Chair Conversion Kit (to LR Delivery Unit) Installation Installation [Kit #002-1966-xx] Attention: Use this kit to convert an Elevance Chair to a Chair with an Elevance LR mounted

More information

Loose Components. VetPro 5000 Wall / Cabinet Mount Installation. Applies to Models:

Loose Components. VetPro 5000 Wall / Cabinet Mount Installation. Applies to Models: VetPro 5000 Wall / Cabinet Mount Installation warning Equipment not suitable for use in the presence of a flammable anesthetic mixture. Applies to Models: 8001-001 8001-002 8001-005 8001-006 Loose Components

More information

Troubleshooting Guide: Elevance Delivery Systems

Troubleshooting Guide: Elevance Delivery Systems Troubleshooting Guide: Elevance Delivery Systems FOR USE BY MIDMARK TRAINED TECHNICIANS Contents Description / Links Troubleshooting Charts ICM Screens Assistant s Unit Instruments (Elevance & European)

More information

Mirage Dental Delivery Unit MSP3500/3550 Installation Instructions

Mirage Dental Delivery Unit MSP3500/3550 Installation Instructions ! Mirage Dental Delivery Unit MSP3500/3550 Installation Instructions TPC 851 S. Lawson St. City Of Industry, CA 91748 P626-810-4337 Fax 626-810-4245 REV. 1-1-13 Table on Contents: Page GENERAL INFORMATION

More information

Procenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation

Procenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation Procenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation Electrical Requirements: 24 VAC, 3.2 Amp 13VAC, 2 Amp Attention These instructions apply to Midmark cabinetry. For other

More information

2016 Wand Handle Repair Instructions & Parts List

2016 Wand Handle Repair Instructions & Parts List 2016 Wand Handle Repair Instructions & Parts List Updated 9/11/18 2018 by Crafco, Inc. All Rights Reserved 2016 New Style Wand Assembly - Part Number 52200 This style wand assembly is field serviceable.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-448B (Blue Finish) 21-448C (Gun Metal Grey Finish) 21-448P (Vauum Metalized Chrome-VMC) 21-448R (Red Finish)

More information

Installation Manual. Model T680A/B Engine Brakes. For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines. Engine Brakes

Installation Manual. Model T680A/B Engine Brakes. For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines. Engine Brakes Engine Brakes Installation Manual Model T680A/B Engine Brakes For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines TecBrake P.O. Box 27822 Houston, Texas 77227 INSTALLATION MANUAL TECBRAKE T680A

More information

Procenter Delivery, Console Mounted on an Elevance Chair Installation Guide

Procenter Delivery, Console Mounted on an Elevance Chair Installation Guide Procenter Delivery, Console Mounted on an Elevance Chair Installation Guide Language of origin: English Equipment Alert Do not remove wraps or packaging from the delivery flex arm assembly until it is

More information

E-LIFT II+ SYSTEM WITH SPRING LEVER FOR A-SERIES AND FULL FRAME LOOMS

E-LIFT II+ SYSTEM WITH SPRING LEVER FOR A-SERIES AND FULL FRAME LOOMS Congratulations on your purchase of the E-Lift II+ system. This system replaces the action of treadling, eliminating leg strain and fatigue. When you activate the Foot Switch, the motor turns, and selected

More information

Trike Conversion Kit. KAWASAKI 1700 Vulcan Voyager Vulcan Vaquero Vulcan Nomad. Installation Instructions

Trike Conversion Kit. KAWASAKI 1700 Vulcan Voyager Vulcan Vaquero Vulcan Nomad. Installation Instructions BY Trike Conversion Kit KAWASAKI 1700 Vulcan Voyager Vulcan Vaquero Vulcan Nomad Installation Instructions REVISED 1-2015 California Sidecar Parts & Technical Support 434.263.8866 Table of Contents: 1.

More information

Performance Inlet Manifold

Performance Inlet Manifold Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with

More information

Gate Valve Maintenance & Adjustment Procedures

Gate Valve Maintenance & Adjustment Procedures Gate Valve Maintenance & Adjustment Procedures 1 Table of Contents I. GATE AND BONNET O-RING 1.5-21 GATE VALVES...3 II. BELLOWS, PNEUMATIC STANDARD 1.5-21 GATE VALVES...5 III. ACTUATOR O-RING 1.5-21 GATE

More information

Discount-Equipment.com

Discount-Equipment.com REQUIRED TOOLS LS Series Remix Shaft Installation Instructions /8", /6", /2" Allen Wrenches Snap Ring Pliers (Light Duty) /" Combination Wrench Loctite #22 Blue /" Socket w/ /8" Ratchet Electric Drill

More information

AmTryke Adult Recumbent Model JT2000 #50-FC-2000

AmTryke Adult Recumbent Model JT2000 #50-FC-2000 AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

AMAYA XT/BRAVO X-Cable Tension Gauge User Instructions

AMAYA XT/BRAVO X-Cable Tension Gauge User Instructions AMAYA XT/BRAVO X-Cable Tension Gauge User Instructions The following instructions will guide you through checking and, if necessary, adjusting the X-Cable tension on your AMAYA XT or BRAVO machine. The

More information

GATE VALVE MAINTENANCE AND ADJUSTMENT PROCEDURES

GATE VALVE MAINTENANCE AND ADJUSTMENT PROCEDURES GATE VALVE MAINTENANCE AND ADJUSTMENT PROCEDURES Valve Maintenance Manual 1 May 15, 2001 Table of Contents TABLE OF CONTENTS... 2 I. GATE AND BONNET O-RING 0.625" - 21" GATE VALVES... 3 II. BELLOWS, PNEUMATIC

More information

Crestline Dampening System. Installation Instructions. Hamada RS34 & VS34 Satellite Unit. For Presses Originally Equipped With. Integrated Dampeners

Crestline Dampening System. Installation Instructions. Hamada RS34 & VS34 Satellite Unit. For Presses Originally Equipped With. Integrated Dampeners Crestline Dampening System Installation Instructions Hamada RS34 & VS34 Satellite Unit For Presses Originally Equipped With Integrated Dampeners X88-113 01/2001 Rev-A GENERAL INFORMATION ATTENTION CRESTLINE

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT ODYSSEY AII 22030 Issue Date AUG 2000 PARTS LIST CD Changer Attachment Kit: P/N 08B12-S0X-100 Right side rail

More information

Assembly and disassembly instructions for WP-Dynamic

Assembly and disassembly instructions for WP-Dynamic Assembly and disassembly instructions for WP-Dynamic 40... 125 Tools required: Size 19 open-ended or ring spanner (WPD DN40 125) Size 7 open-ended spanner Size 4 Allen key Flat screw-driver with 4mm blade

More information

IMO-517 (7027) ISSUE 3/97 ERA12, 25, 50, 83, 125, 167, 208 AND 250 ELECTRIC ACTUATORS INSTALLATION, MAINTENANCE AND OPERATING INSTRUCTIONS

IMO-517 (7027) ISSUE 3/97 ERA12, 25, 50, 83, 125, 167, 208 AND 250 ELECTRIC ACTUATORS INSTALLATION, MAINTENANCE AND OPERATING INSTRUCTIONS ERA12, 25, 50, 83, 125, 167, IMO-517 (7027) ISSUE 3/97 208 AND 250 ELECTRIC ACTUATORS INSTALLATION, MAINTENANCE AND OPERATING INSTRUCTIONS 2 Table of Contents 1 GENERAL...........................................

More information

Contents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment

Contents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment Contents Section 5: Adjustments... 5-3 1. Ball Detect Adjustment... 5-3 2. Transport Band Tension Adjustment... 5-5 3. Transport Band Drive Belt Tension Adjustment... 5-7 4. Ball Cushion Adjustment...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 30230 2006 RSX P/N 08U96-S6M-200 Issue Date JULY 2005 PARTS LIST Cigarette lighter 3. Turn the two knobs counterclockwise, and remove

More information

FINA SUSPENDED INSTALLATION INSTRUCTIONS

FINA SUSPENDED INSTALLATION INSTRUCTIONS FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation... 2-4 AC Cable to Hub Mounting (AH4) Installation... 5-7 Pendant Pipe Mounting Installation... 8-9 Canopy Detail... 10-11

More information

INSTALLATION INSTRUCTIONS DOCUMENT REVISION : /17/2014

INSTALLATION INSTRUCTIONS DOCUMENT REVISION : /17/2014 INSTALLATION INSTRUCTIONS DOCUMENT REVISION : 1.0 10/17/2014 LPF COMPONENT LIST LPF W/ WIRE & GROMMET ( 1 ) M6 X 20MM SCREW ( 2 )* LPF DRIVER BOX ( 1 ) REVERSE CIRCUIT WIRE ( 1 ).25 THICK LICENSE PLATE

More information

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market 1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter

More information

Assembly Instructions

Assembly Instructions ZBX-540E Safety Cover Assembly Instructions This document provides instructions for service personnel. These procedures should not be performed by the end user. Important Notes on Assembly Operations WARNING

More information

Assault Air Bike Assembly Instructions

Assault Air Bike Assembly Instructions Assault Air Bike Assembly Instructions Tools Needed: Box Cutter 6mm Hex Wrench Phillips Screw Driver 13mm Wrench 22mm Wrench 15mm Wrench Step 1: Lay the Assault Airbike Bike box on the ground. Step 3:

More information

Always wear safety glasses when working on your vehicle.

Always wear safety glasses when working on your vehicle. 90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively

More information

Track Light with Monitor Installation Guide

Track Light with Monitor Installation Guide Track Light with Monitor Installation Guide This installation requires at least two service technicians. Track with light and monitor weight (max.) is 157 Lbs. (71 kgs). Applies to Models: 1531017 (-000

More information

Cummins 6.7 Litre 2500/3500 Diesel EGR System. Always wear gloves and safety glasses when performing this service

Cummins 6.7 Litre 2500/3500 Diesel EGR System. Always wear gloves and safety glasses when performing this service Cummins 6.7 Litre 2500/3500 Diesel EGR System Always wear gloves and safety glasses when performing this service EGR System Consists of: Cold side EGR valve (after EGR cooler) controls exhaust gases for

More information

Crestline Dampening System. Installation Instructions. Ryobi 500N X /98

Crestline Dampening System. Installation Instructions. Ryobi 500N X /98 Crestline Dampening System Installation Instructions Ryobi 500N X88-33 7/98 GENERAL INFORMATION ATTENTION CRESTLINE DAMPENER OWNER! Accel Graphic Systems provides parts and service through its authorized

More information

Ford Focus Zetec SVT Timing Belt

Ford Focus Zetec SVT Timing Belt 2000-2004 Ford Focus Zetec SVT Timing Belt Replacement This guide will show you how to replace the timing belt on the 2.0L DOHC Zetec with VCT on a 2002 Ford Focus SVT. This is an interference motor. Written

More information

AirHawk Gauge and Alarm Assembly

AirHawk Gauge and Alarm Assembly AirHawk Gauge and Alarm Assembly MAINTENANCE AND REPAIR MSA 511 (L) Rev. 4 MSA 2015 Prnt. Spec. 10000005389 (I) Mat. 10079636 Doc. 10079636 AIRHAWK GAUGE AND ALARM ASSEMBLY AIRHAWK GAUGE AND ALARM COMPONENTS

More information

AmTryke Adult Recumbent Model HP1000 #50-HC-1000

AmTryke Adult Recumbent Model HP1000 #50-HC-1000 AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

BMW/Isuzu 3.0 Liter Diesel EGR Cleaning Instructions

BMW/Isuzu 3.0 Liter Diesel EGR Cleaning Instructions BMW/Isuzu 3.0 Liter Diesel EGR Cleaning Instructions EGR System Consists of: 2 Cold side EGR valves (after EGR coolers), high pressure loop and a low pressure loop which controls exhaust gases for proper

More information

P44 Stepper. User Manual

P44 Stepper. User Manual P44 Stepper User Manual Table of Contents Introduction 1 Safety Warning 2 Overview of Parts 2 Attaching to Chair 3 Manoeuvring Around 4 Setting Pedal Stops 4 Getting On 5 Setting the Resistance (models

More information

Installation Instructions for Model CityFix

Installation Instructions for Model CityFix INTERLIFT Interlift, Inc. 15939 Piuma Ave. Cerritos, CA 90703 Tel: 888-774-5844 Fax: 562-924-8318 Installation Instructions for Model CityFix www.interlift.net 1. LIFT LOCATION The installation surface

More information

4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368

4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368 4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368 DEVICES COVERED IN THESE INSTRUCTIONS: RX Request to Exit ELECTRICAL SPECIFICATIONS Note: SPDT mechanical

More information

Model 579 Curtain Machine Manual. General Information. Unpacking:

Model 579 Curtain Machine Manual. General Information. Unpacking: Model 579 Curtain Machine Manual. General Information The Model 579 curtain machine is designed for use with most light duty commercial and residential drapery tracks. The 579 curtain machine is designed

More information

Mercedes Sprinter 3.0 Liter ( ) Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service

Mercedes Sprinter 3.0 Liter ( ) Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service Mercedes Sprinter 3.0 Liter (2007-2013) Diesel EGR Cleaning Instructions Always wear gloves and safety glasses when performing this service EGR System Consists of: Cold side EGR valve (after EGR cooler)

More information

Installation Manual. Model T675A Engine Brakes. For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines.

Installation Manual. Model T675A Engine Brakes. For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines. Engine Brakes Installation Manual Model T675A Engine Brakes For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines TecBrake P.O. Box 27822 Houston, Texas 77227 INSTALLATION MANUAL TECBRAKE

More information

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.

More information

EGR Adapter Ford 6.7 L

EGR Adapter Ford 6.7 L EGR Adapter Ford 6.7 L Part No. 069-3390 CAUTION: Always wear gloves and safety glasses when performing this service EGR System Consists of: Hot side EGR valve (before EGR cooler) controls exhaust gases

More information

Asepsis 21 Delivery Unit

Asepsis 21 Delivery Unit INSTALLATION INSTRUCTIONS for the Console Mounted TM Asepsis 21 Delivery Unit SECTION I - REQUIREMENTS 1. PHYSICAL REQUIREMENTS... 1 2. ELECTRICAL REQUIREMENTS... 1 3. WATER SUPPLY REQUIREMENTS... 1 4.

More information

CHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS

CHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS Chemical Mixing System Operating and Installation Instructions for Focus II Mid-Size Walk-Behind Kit #11363A CHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips Screwdriver

More information

SECTION C Engine 5.4L (4V)

SECTION C Engine 5.4L (4V) 303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing

More information

ASSEMBLY INSTRUCTIONS / OWNERS MANUAL AIR BIKE AB-1

ASSEMBLY INSTRUCTIONS / OWNERS MANUAL AIR BIKE AB-1 AIR BIKE AB- ASSEMBLY INSTRUCTIONS / OWNERS MANUAL IMPORTANT : READ ALL ASSEMBLY INSTRUCTIONS AND SAFETY PRECAUTIONS BEFORE USING THIS PRODUCT. REFERENCE ALL SAFETY GUIDELINES AND WARNING LABELS. RETAIN

More information

N/S= Not Shown Bold = Part available for purchase. Italic = Part not available for purchase, listed and shown for reference only.

N/S= Not Shown Bold = Part available for purchase. Italic = Part not available for purchase, listed and shown for reference only. Media Rewind Upgrade Installation Instructions Prepare for Installation This kit includes the parts and documentation necessary to install the media rewind option kit into the 105SL printers. Read these

More information

Setting the World s Performance Standards

Setting the World s Performance Standards Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Forced Air Hot Air Elimination Kit (Bed Fan Kit) For 800 RZR-4 P/N 67-165 Kit Contents:

More information

200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge

200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge 200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 642E Centrifuge MODEL 642E SERVICE MANUAL REV: Original Issue 1 CONTENTS

More information

Halogen NiMH. Evolution USER GUIDE

Halogen NiMH. Evolution USER GUIDE Halogen NiMH Evolution USER GUIDE DISCOVER THE NIGHT! Thank you for choosing the Evolution system from NiteRider, the innovator in technical lighting systems. The Evolution is an easy-to-use, high-intensity

More information

Service Bulletin. HIITMill (X) Brake Lever Drift

Service Bulletin. HIITMill (X) Brake Lever Drift HIITMill (X) Brake Lever Drift Applies to: HIITMill (9-4590) + HIITMIll X (9-4640) On some HIITMill and HIITMill X units, the brake lever can drift when the user is Rev. A applying load to the belt. This

More information

Lift N Go [Model 210] Electric Carrier For use with power chairs & scooters Installation Guide & Owners Manual

Lift N Go [Model 210] Electric Carrier For use with power chairs & scooters Installation Guide & Owners Manual 203 Matzinger Road Toledo, OH 43612 Phone: 1-800-541-3213 Fax: (419) 478-4425 www.wheelchaircarrier.com E-mail: admin@wheelchaircarrier.com Lift N Go [Model 210] Electric Carrier For use with power chairs

More information

Contents. Overview Pinsetter Orientation...1-4

Contents. Overview Pinsetter Orientation...1-4 Contents Overview...1-3 Pinsetter Orientation...1-4 Pinsetter Description...1-5 Ball Pit...1-5 Ball Cushion...1-5 Transport Band...1-7 Ball Accelerator...1-8 Pin Elevator...1-10 Distributor...1-14 Setting

More information

RIGHT HYDRAULIC PUMP. Right Hydraulic Pump Replacement. Right Hydraulic Pump Removal. 5. Remove the pump belt from around the pump pulleys (Fig. 002).

RIGHT HYDRAULIC PUMP. Right Hydraulic Pump Replacement. Right Hydraulic Pump Removal. 5. Remove the pump belt from around the pump pulleys (Fig. 002). Right Hydraulic Pump Replacement Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all exposed surfaces prior to any type of maintenance. Cleaning all parts

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application 2012 CIVIC 2 AND 4-DOOR Publications No. AII 45605 Issue Date APR 2011 PARTS LIST Attachment Kit P/N 08V03-TR0-100 Automatic day/night mirror harness Automatic

More information

Mercedes GLK250 ( ) 2.1L Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service

Mercedes GLK250 ( ) 2.1L Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service Mercedes GLK250 (2013-2015) 2.1L Diesel EGR Cleaning Instructions Always wear gloves and safety glasses when performing this service EGR System Consists of: Hot side EGR valve (before EGR cooler) controls

More information

Discount-Equipment.com

Discount-Equipment.com LS40D, LS40TD, LS50TD, LS60TD LS-Series Remix Shaft Coupler Retrofit Kit Installation Instructions The following instructions are intended to assist the user in the installtion of the LS-Series Remix Shaft

More information

INSTALLATION GUIDE. Kawasaki KLR Manual Revision:

INSTALLATION GUIDE. Kawasaki KLR Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Kawasaki KLR650 191-640 Manual Revision: 030308 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714

More information

RAM Rail Mount Kit RAM 201UD 5 Arm RAM 2461U Base RAM 235U Base, Double U-Bolt

RAM Rail Mount Kit RAM 201UD 5 Arm RAM 2461U Base RAM 235U Base, Double U-Bolt Note: Indented items indicate parts included in an assembly listed above. Part Name/Description Part Number Quantity Direct Command Kit 4100514 1 Installation Instructions 2005690 1 CAN Y-Splice 4000137

More information

INSTALLATION INSTRUCTIONS for the LR Chair

INSTALLATION INSTRUCTIONS for the LR Chair INSTALLATION INSTRUCTIONS for the LR Chair SECTION I - REQUIREMENTS 1. PHYSICAL REQUIREMENTS... 1 2. ELECTRICAL REQUIREMENTS... 1 SECTION II - INSTALLATION 1. UNPACKING THE CARTONS... 2 2. UNPACKING THE

More information

Flex Work Station Delivery Units Installation Guide

Flex Work Station Delivery Units Installation Guide Flex Work Station Delivery Units Installation Guide Special Tools Level 1/4" Deep Well Socket 3/8" Masonary Bit 9/32" Wood Bit Hammer Drill Remove any packaging from the skid and the floor or wall mount

More information

T-630 with John Deere Electronic Engines Troubleshooting

T-630 with John Deere Electronic Engines Troubleshooting T-630 with John Deere Electronic Engines Troubleshooting The T-630 is equipped with a digital readout located in the Gray Box on the right side of the engine compartment. This diagnostic gauge gives hours,

More information

Upgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki.

Upgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki. SeeMeCNC Guides Upgrade v3 to v3.2 Rostock Max v3 Uprgade to v3.2 Written By: SeeMeCNC 2018 seemecnc.dozuki.com/ Page 1 of 34 INTRODUCTION This guide is intended to Upgrade a Rostock Max v3 to a Rostock

More information

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission

More information

CJRK Tactical Riflescope Mount

CJRK Tactical Riflescope Mount USER MANUAL CJRK Tactical Riflescope Mount SM34004 English ENGLISH FEATURES: Quick detach weaver/picatinny mount Quick detach provides return to zero Cantilever design provides proper eye relief on various

More information

Tooling Assistance Center

Tooling Assistance Center Safeguards are designed into this application equipment to protect operators and maintenance personnel from most hazards during equipment operation. However, certain safety precautions must be taken by

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-448 2005 CHEVROLET Cavalier Ecotec L4-2.2L SEE * NOTE 2005 PONTIAC Sunfire L4-2.2L C.A.R.B. E.O. # D-392-28 2003-2004

More information

Instruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents

Instruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents Instruction Sheet Kit Numbers: 5600, 5700, 5800 & 5300 CRANK PULLEY KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand, and follow all safety

More information

EGR Adapter Mercedes Sprinter 3.0L ( )

EGR Adapter Mercedes Sprinter 3.0L ( ) EGR Adapter Mercedes Sprinter 3.0L (2007-2013) Part No. 069-3388 CAUTION: Always wear gloves and safety glasses when performing this service EGR System Consists of: Cold side EGR valve (after EGR cooler)

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram 1500 Crew Cab 2009 - Current : 75138-15 Dodge Ram 2500/3500 & HD Crew Cab 2010 - Current : 75138-15

More information

OFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION

OFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION OFS 400A FIBER OPTIC INTERCONNECT 636-299-109-01 Instruction Sheet UNIT (FOIU) Comcode 846 586 212 INSTALLATION This instruction sheet covers the 400A1 (106266901) and 400A2 (106414170) Fiber Optic Interconnect

More information

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax) INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing

More information

491 Harness Installation Kit

491 Harness Installation Kit 491 Harness Kit 002-0759-00 Kit Components: Qty Harness Assy... 1 Wire Clip... 2 Wire Tie (7 1/2 )... 5 Wire Tie (7 1/4 )... 4 Instruction... 1 Remove Back Cover Warning Disconnect Power before removing

More information

Mandatory X Information Recommended Change. Series/Parts Affected: LS40D, LS40TD, LS50TD and LS60TD Concrete Pumps

Mandatory X Information Recommended Change. Series/Parts Affected: LS40D, LS40TD, LS50TD and LS60TD Concrete Pumps Service Bulletin No. CP20060428 Subject: Remix Shaft Coupler Retrofit Kit Model: LS40D, LS40TD, LS50TD & LS60TD Product Group: Concrete Pump Date: April 28, 2006 SERVICE BULLETIN Group: CP Mandatory X

More information

INSTALLATION INSTRUCTIONS 8" CONTINUOUS FLOW/TRANSFER AUGER QUICK RELEASE POWERHEAD 702B-001A AND 702E-001A

INSTALLATION INSTRUCTIONS 8 CONTINUOUS FLOW/TRANSFER AUGER QUICK RELEASE POWERHEAD 702B-001A AND 702E-001A INSTALLATION INSTRUCTIONS 8" CONTINUOUS FLOW/TRANSFER AUGER QUICK RELEASE POWERHEAD 702B-001A AND 702E-001A SHIVVERS MANUFACTURING, INC. 614 W. ENGLISH STREET CORYDON, IA 50060 PH (641) 872-1005 **FAX

More information

Classic Light Bar Mustang

Classic Light Bar Mustang Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket

More information

FLEETWOOD TRAVEL TRAILER SLIDEOUT SYSTEM OWNER S MANUAL

FLEETWOOD TRAVEL TRAILER SLIDEOUT SYSTEM OWNER S MANUAL FLEETWOOD TRAVEL TRAILER SLIDEOUT SYSTEM OWNER S MANUAL 82 S0150 01 REV. 1 April, 2002 TABLE OF CONTENTS PAGE # OPERATIONS MANUAL... 1 1. SYSTEM DESCRIPTION... 1 1.1 MAJOR COMPONENTS... 1 2. HOW TO OPERATE

More information

CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT

CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.

More information

L Ford Power Stroke Intercooler Pipe Upgrade

L Ford Power Stroke Intercooler Pipe Upgrade Rev: 10.30.14 TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email

More information

Part# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source)

Part# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source) Part# 18-1819 JL AIR IT UP 4 Tire On Board Air Delivery System (Requires External Air Source) The most up-to-date instructions always visit www.updownair.com www.updownair.com 833-226-4863 I M P O R T

More information

LEFT HYDRAULIC PUMP. Left Hydraulic Pump Replacement. Left Hydraulic Pump Removal. 5. Remove the pump belt from around the pump pulleys (Fig. 002).

LEFT HYDRAULIC PUMP. Left Hydraulic Pump Replacement. Left Hydraulic Pump Removal. 5. Remove the pump belt from around the pump pulleys (Fig. 002). Left Hydraulic Pump Replacement Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all exposed surfaces prior to any type of maintenance. Cleaning all parts

More information

ADVANTAGE Annual Preventive Maintenance Instructions

ADVANTAGE Annual Preventive Maintenance Instructions ADVANTAGE Annual Preventive These instructions should be followed to perform preventive maintenance on the Advantage reprocessor. Before commencing work on the reprocessor, ensure that you have the appropriate

More information

HAND THROTTLE KIT For Workman 3000 Series

HAND THROTTLE KIT For Workman 3000 Series FORM NO. 7 6 MODEL NO. 0746 INSTALLATION INSTRUCTIONS HAND THROTTLE KIT For Workman 000 Series. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition

More information

SECTION C Engine 5.4L (3V)

SECTION C Engine 5.4L (3V) 303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Timing

More information

SERVICE MANUAL. Chairman HD3

SERVICE MANUAL. Chairman HD3 SERVICE MANUAL Chairman HD3 US How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Edition no.3, 2009-08 Article no.: 201161-US-0 Contents Contents

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AUTOMATIC AII 27160 2005 CR-V Issue Date ATTACHMENT KIT SEP 2004 PARTS LIST Automatic Day/Night Mirror Attachment Kit (sold separately)

More information

Parts Catalog SLICING MACHINES

Parts Catalog SLICING MACHINES Parts Catalog 00N Slicer SLICING MACHINES MODELS: 00N, 0N & 9N -- IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF SLICER. GLOBE FOOD EQUIPMENT COMPANY

More information

ASSEMBLY AND SET-UP INSTRUCTIONS

ASSEMBLY AND SET-UP INSTRUCTIONS TOTAL GYM POWERTOWER TM ASSEMBLY AND SET-UP INSTRUCTIONS TOTAL GYM POWERTOWER BOX CONTENTS: Tower, Rail and Glideboard Assembly Bars and Arm Pulley Cable Assembly Folding Platform Telescoping Squat Stand

More information

MANUAL. Tyr MOT 250 English

MANUAL. Tyr MOT 250 English MANUAL Tyr MOT 250 English Manual for Tyr MS 250 Before bolting the machine into position, install the launching arm guard, the magazine and the launching arm. Connect the wiring. Load a small amount of

More information