Electrical Testing in the Operating Room; Part 6

Size: px
Start display at page:

Download "Electrical Testing in the Operating Room; Part 6"

Transcription

1 DOCTORDOCTOR It hurts when I shift! by Randall Schroeder Electrical Testing in the Operating Room; Part 6 IIn the operating room, doctors are faced with precise test procedures that are challenging and need to be done correctly to prevent damage. If done incorrectly, these procedures not only waste time, but can also be costly in unnecessary parts replacement or circuit damage. So far, here is what we have covered in this series: Part 1 The importance of power and grounds, and how to check them properly (GEARS January/February 2002). Part 2 Testing temperature sensors and throttle position sensors; starting tests at the sensor and confirming them at the computer (GEARS March 2002). Part 3 Park/neutral switches and accelerator switches. Along with the park/neutral switches, we led into range selectors, which are a very important input, not only for line rise in electronicallycontrolled transmissions, but also how they tie in with the range the driver has selected (GEARS October 2002). Part 4 Speed sensing devices and pressure switches. We covered the similarities in the different speed sensors and how to check them. We looked at pressure switches and their uses, and learned that the name switch is exactly what the name implies: an onoff device, like a light switch (GEARS JanuaryFebruary 2003). Part 5 Shift solenoids; how the computer takes the inputs we covered earlier, and uses that information to control the shift solenoids to create an upshift or downshift at perfect speeds (well, in theory). Basically, shift solenoids have taken the place of governor pressure to move the shift valves, when valves are used; and in some instances Figure 1 taken the place of the valves altogether (GEARS April 2003). In this issue of Doctor, Doctor, we re going to look at line pressure solenoids, governor solenoids (42RE/47RE), and modulating shift solenoids (32 4L60E). When you understand how these solenoids work, it is easier to see how they affect shift feel and timing. The theory is simple: Solenoids can be used to alter shift feel (accumulator solenoid), control governor pressure (shift timing), and most commonly, take the place of the TV oil (throttle valve or modulator) that was used for line rise (pressure regulation). This is called managed oil flow into a circuit. Figure 2 78 GEARS September 2003

2 The computer uses a solenoid to achieve this managed oil flow by pulsing the solenoid on and off (duty cycle) to regulate a supplied oil pressure. This pressure either moves a shift valve or sends oil directly into the pressure control valve boost circuit. This is similar to the valve control in nonelectronic transmissions, but uses electrical signals to achieve the same results. Common names for these solenoids are: EPC Electronic Pressure Control (line pressure) Force Motor Variable pressure control (line pressure) Pressure Control Solenoid Line pressure Modulated TCC Solenoid Torque converter 32 Shift Solenoid Modulated downshift Solenoid Block 41TE/42LE Governor Pressure Solenoid 42RE/47RE Shift Solenoids Many imports and Chryslers Line Pressure Control Solenoids Line pressure solenoids have taken the place of the TV or vacuum modulator used on earlier transmissions to boost pressure. As line pressure (regulated through a valve or not) goes through the solenoid, it sends a regulated amount of pressure to act on the boost valve through its sleeve in the regulator valve lineup. This pressure supplies the extra force needed to move the boost valve against the regulator valve, causing line rise (figure 1). If everything was perfect, the oil pressure from the solenoid at idle would be 0 PSI. Since things aren t always perfect, there will usually be about 5 to 10 PSI feeding the boost circuit at idle, and the pressure goes up from there. The oil from the solenoid (called conventional TV oil pressure) is directed to the pressure boost valve (figure 2). This moves the PR valve toward boost pressure. Line pressure boosts when the PR valve moves down toward the bottom of its bore. IMPORTANT: If there s a problem with balance oil on the PR valve, line pressure will be high, even if the solenoid is doing its job correctly. Testing these solenoids can be Expertise to help steer you in the right direction. Throughout the years, Fred Burkhart and Brent Funk have built up the RoadMaster name with the knowledge and skill that only comes through industry experience. But you can never have too many experts on the job and that s why we are pleased to welcome Bill Anthony as Director of R&D and Jeff CollinsworthSales Manager, into our family. With decades of industry experience among us, we know this decision will give us the advantage and expertise to keep providing you with the most dependable parts on the market. Having the parts you need is essential. Knowing what you need is the difference. RoadMaster offers a complete line of parts that deliver the quality and performance you demand. And now we ve added over 50 new solenoid, actuator, and sensor part numbers to our growing line. So when you need reliable parts backed by the experts, remember RoadMaster. Contact us today for prices and a distributor near you. CORPORATE: 1016 Dixie Highway, Suite B, Rossford, OH Phone: Fax: fburkttxe@inetmail.att.net DISTRIBUTION CENTER: 416 Justice St., Fremont, OH Phone: Fax: ttxeinc@nwonline.net GEARS September

3 Electrical Testing in the Operating Room; Part 6 tricky, but they all work basically the same way. GM varies the current flow to the solenoid, from 1.1 amps at normal operation, down to 0.0 amps for maximum pressure. Since the system controls pressure by varying current flow through the solenoid, the best way to monitor system operation is with an ammeter in series with the solenoid (figure 3). Scan tools will usually provide the amperage signal that the computer provides. This solenoid operates from a duty cycle signal in the positive circuit of about Hz (figure 4). At minimum throttle (idle), the signal ontime increases, so the current flow approaches 1.1 amps. This keeps the armature forced back against the plunger, compressing the spring, and holding the valve plunger up. In this condition, there s no filtered actuator feed oil flow (figure 5). As the load increases, current decreases, which lowers the field force pulling on the spring. At full throttle, current flow drops to 0.0 amps, and the plunger settles to the bottom of the solenoid. This allows maximum actuator oil flow, which creates maximum pressure (figure 6). Sound simple? Once you understand it, it really is. Let s look at the Ford VPS (Variable Pressure Solenoid). Many people refer to this as the EPC solenoid, or Electronic Pressure Control solenoid. Ford regulates the ground side of the EPC to increase current flow through the solenoid, and raise system pressure. At idle, this circuit should have 7 volts on the ground side, and it should drop to almost zero volts at hard throttle. This is how you may have seen it on your scan tools. It s often easier to test these solenoids by connecting your voltmeter s positive lead to the solenoid positive wire, and the negative lead to the solenoid negative wire (figures 7A,7B). This will provide a different measurement than the one you see on your scan tool; in fact, you ll see the opposite reading altogether. Instead of voltage rising with line pressure, the voltage drops as line pressure increases. With this setup, voltage is usually around 5 volts at idle, and drops to almost 0.0 volts at hard Force Motor amps Figure 3 throttle. This is no different than unplugging the transmission to create maximum pressure. IMPORTANT: While we use 12 volts to describe system voltage in this discussion, don t forget that system voltage will usually be somewhat higher; about 14 volts or so with the engine running. Which means the idle voltage may be a bit higher than discussed; maybe 6 volts or more. Always compare the solenoid feed voltage with the system voltage. Any substantial difference indicates unwanted resistance in the circuit. The working voltage for the pressure control solenoid should be around 5V for 0 PSI boost pressure in the TV circuit. When the working voltage drops to 0 volts, TV pressure should boost Figure 4 Figure 6 PRESSURE CONTROL SOLENOID Figure 5 EPC Voltage Decreases from 5v to 0v DC EPC Voltage Increases from 6v to 13v DC Ignition Trans. relay Gov. Solenoid Figure 7A Figure 7B Figure 8 80 GEARS September 2003

4

5 Electrical Testing in the Operating Room; Part 6 upwards of 90 PSI (EPC pressure boost pressure can go as high as 120 PSI). This would be the same as if you d unplugged the solenoid. If the vehicle you re working seems to be slipping, install a pressure gauge and disconnect the power to the solenoids; the system should jump to maximum line pressure. If the line pressure doesn t rise to maximum, look for a leaking solenoid or internal transmission problems. Disconnecting the solenoid is a simple check to make sure the transmission line rise is working properly. To help with diagnoses, test the signals on every vehicle that come into your shop, and keep a chart for future use. Record keyoff voltages, keyon voltages, and enginerunning voltages. Having these voltage measurements available makes diagnoses a snap if you suspect you re dealing with an electrical failure. Governor Solenoid The governor solenoid in the Chrysler 4247RE rear wheel drive unit works similar to the EPC solenoid, with one exception: It isn t used for line rise. Just like the EPC solenoid, the governor solenoid is ground controlled; that is, the positive feed to the solenoid remains at full system voltage. This voltage comes from a power relay supplying system voltage directly. The control unit controls the ground side of the circuit to raise and lower governor pressure. Test this solenoid the same way you did the Ford EPC solenoid: Connect your positive voltmeter lead to the positive solenoid wire, and the negative lead to the negative wire (figure 8). There should be around 5 to 6 volts with 0 PSI in the governor circuit. As the voltage drops, governor pressure increases. This system has a very sensitive system of checks and balances, so the computer knows exactly how much governor pressure there is at all times. If line pressure to the governor solenoid is high a common situation after a performance modification to line pressure the computer will set an offset code and turn the system relay off. Unlike regular pressure control solenoids, governor pressure is only used to stroke the shift valves. For more information on testing the governor circuit, refer to the articles in the 2001 September and October issues of GEARS. They explain in detail how to check this system. Modulating Shift Solenoids Modulated shift solenoids receive a varying voltage during the shift. They are still onoff solenoids, but the current builds slowly until the solenoid is fully energized. This type solenoid allows the computer to regulate shift feel. The advantage to this type of solenoid is that it works like an orifice or accumulator: By controlling the apply rate of the solenoid, the computer can slow down or speed up a shift, depending on driver s needs. An example of this type of solenoid would be the 32 solenoid (figure 9) used on early 4L60E transmissions. The PCM modulates the current (duty cycle) to control the 32 solenoid on the ground side (figure 10), the same way it does for many other modulating solenoids. The 32 solenoid is off in first gear. In other gears, the 32 solenoid is energized to 90% (figure 11). When the transmission downshifts 32, the signal duty cycle will drop to about 20%. This regulates hydraulic pressure to release the 34 clutch and apply 2 4 band smoothly during the 32 downshift. The computer monitors circuit voltage on these systems when it energizes the solenoid (grounded). If the voltage stays high for 4 seconds, the computer will set a code for that solenoid. You will find this type of solenoid in many units, so make sure you understand the difference between an onoff solenoid and one that is dutycycle controlled. Understanding these electrical tests, and differences between them, can make your job easier. With electrical systems testing, the preset voltages will always be either within spec or they won t. The job is to know where to look when the voltages are out of range, and how the effects will be used in transmission control. Until next time, keep those transmissions in good health! The Doctor Figure 9 Figure 10 Figure GEARS September 2003

In the operating room, transmission

In the operating room, transmission DOCTOR DOCTOR It hurts when I shift! REPRINT FROM MARCH 2005 SEE PART 2 ON PAGE 24 by Randall Schroeder In the operating room, transmission surgeons are often faced with split-second decisions regarding

More information

In the last issue of Let s LET S PLAY BALL. Every code represents a perceived failure to the computer. by Lance Wiggins

In the last issue of Let s LET S PLAY BALL. Every code represents a perceived failure to the computer. by Lance Wiggins LET S PLAY BALL by Lance Wiggins A Look at the 450-43LE (Aisin Seiki), Part 2 Please note: In the April issue of GEARS, Aisin Seiki was spelled incorrectly. The correct spelling is listed above. Our apologies

More information

Chronic Valve Body Wear

Chronic Valve Body Wear Chronic Valve Body Wear by Larry Frash Every penny I ve earned in my life has been from the automotive industry. For that, I am thankful. If the manufacturers made a perfect vehicle, all we could hope

More information

VW 09G. Bumping. Welcome back to another TALES FROM THE BENCH. TCC Valves. by Jarad Warren members.atra.com

VW 09G. Bumping. Welcome back to another TALES FROM THE BENCH. TCC Valves. by Jarad Warren members.atra.com Bumping VW 09G TALES FROM THE BENCH Bumping VW 09G by by Jarad Warren members.atra.com Welcome back to another addition of Tales from the Bench. In this issue of GEARS, we re going to look at a 2005 Volkswagen

More information

Educating the AF33-5. As 2007 quickly approaches its end and 2008 is in LET'S PLAY BALL. by Lance Wiggins

Educating the AF33-5. As 2007 quickly approaches its end and 2008 is in LET'S PLAY BALL. by Lance Wiggins LET'S PLAY BALL Educating Spe aker the AF33-5 by Lance Wiggins As 2007 quickly approaches its end and 2008 is in sight, it occurred to me that my 20th high school reunion is coming up next year. 20 years

More information

Ford. After rebuilding a 5R55W/S model transmission, during the road test you may encounter a are on the 2 3 shift.

Ford. After rebuilding a 5R55W/S model transmission, during the road test you may encounter a are on the 2 3 shift. 112 Erratic Transmission Operation After rebuilding a model transmission, during the road test you may encounter a are on the 2 3 shift. This concern can be caused by a new solenoid pack. Over the years,

More information

A Fresh Take. on Chrysler s Pressure. Figure 1

A Fresh Take. on Chrysler s Pressure. Figure 1 A Fresh Take on Chrysler s Pressure Boost System BEYOND THE BASICS A Fresh Take on Chrysler s Pressure by Dennis Madden members.atra.com Boost System Boost Valve Exhaust Boost Tube Figure 1 Ifind some

More information

Torque Convertor Control System

Torque Convertor Control System 22 September 2015 PN#1030395 TorqLoc (I-00208) 1 BD TorqLoc Torque Convertor Control System Part# 1030395 Installation Manual for the following applications: BD Brakes for Dodge, Ford and Chevrolet Pac

More information

Interchanges are a fact of life for. Interchanges for the E4OD and 4R100 STREET SMART. by Mike Brown

Interchanges are a fact of life for. Interchanges for the E4OD and 4R100 STREET SMART. by Mike Brown STREET SMART by Mike Brown Interchanges for the E4OD and 4R100 Figure 1 Figure 2 Interchanges are a fact of life for transmission repair. Maybe you can t get the original part anymore; maybe you just can

More information

In the first part of this series on

In the first part of this series on by Mike Van Dyke In the first part of this series on diagnosing ECUs, we went over some basic visual diagnosis of common failures. In this, the second part of the series, we re going to go over some basic

More information

The AW55-50SN transmission

The AW55-50SN transmission TECHNICAL TRAINING Shift Pointers Author: Jesse Zacarias Subject: Drive and Reverse engagement problems Unit: AW55-50SN (Nissan RE5F22A, GM AF33-5) Vehicle Applications: 2005 Nissan Altima Essential Reading:

More information

VAGABOND S HANDBOOK TRANSMISSION

VAGABOND S HANDBOOK TRANSMISSION 03/24/07 TRANSMISSION Transmission won t engage into Gear This is caused usually by too low a Voltage to get into the ECM. This unit requires a minimum of 9VDC in order to operate at all. Almost all erratic

More information

In the last two issues of GEARS, we

In the last two issues of GEARS, we Diagnosing Pressure Control Circuits Part 3 of a 3-Part Series by Steve Bodofsky In the last two issues of GEARS, we looked at how solenoids can be used to control pressures. We examined the signals that

More information

Selected excerpts from the book: Lab Scopes: Introductory & Advanced. Steven McAfee

Selected excerpts from the book: Lab Scopes: Introductory & Advanced. Steven McAfee Selected excerpts from the book: Lab Scopes: Introductory & Advanced Steven McAfee 1. 2. 3. 4. 5. 6. Excerpt from Chapter 1 Lab Scopes How do they work? (page 6) Excerpt from Chapter 3 Pattern Recognition

More information

How Regenerative Braking Works

How Regenerative Braking Works Feature How Regenerative Braking Works The regenerative braking systems on Nissan hybrid vehicles can be confusing and misunderstood. Let s take a look at how these systems really work. 26 Nissan TechNews

More information

Throttle Body Instruction Sheet

Throttle Body Instruction Sheet Throttle Body Instruction Sheet Thank you for purchasing our modified O.E.M. or new Billet throttle body. They have proven to give considerable power increases when properly adjusted and used alone on

More information

New Problems Facing the 09G

New Problems Facing the 09G Fun with Transmissions New Problems Facing the 09G by Bill Brayton www.atra.com Back in 2008 Dave Skora wrote a series of articles introducing the VW 09G 6-speed transmission. That was before most shops

More information

46RE, 46RH, 47RE, 47RH ZIP KIT

46RE, 46RH, 47RE, 47RH ZIP KIT 46RE, 46RH, 47RE, 47RH ZIP KIT PART NUMBER 46-47RHE-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. installation Diagram 7 1 Separator

More information

We hear a lot of questions

We hear a lot of questions Common Codes and Corrections for the Allison LCT by Steve Garrett 1000 We hear a lot of questions about diagnostic trouble codes for Allison s Light Commercial Truck (LCT) 1000 transmission. Many of the

More information

The Toyota A750E was first

The Toyota A750E was first A Closer Look at the Toyota A750E Valve Body by Mike Brown members.atra.com Figure 1 The Toyota A750E was first introduced in the 2003 4-Runner and Land Cruiser, and the Lexus LX400 and GX470. Since then

More information

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2015 CLOVER SYSTEMS All Rights Reserved

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2015 CLOVER SYSTEMS All Rights Reserved DR310 TM Electronic Dynamo Regulator INSTRUCTION MANUAL COPYRIGHT 2015 CLOVER SYSTEMS All Rights Reserved INTRODUCTION The Clover Systems DR310 is an allelectronic voltage and current regulator for dynamos

More information

Troubleshooting Guide for Limoss Systems

Troubleshooting Guide for Limoss Systems Troubleshooting Guide for Limoss Systems NOTE: Limoss is a manufacturer and importer of linear actuators (motors) hand controls, power supplies, and cables for motion furniture. They are quickly becoming

More information

Honda Accord/Prelude

Honda Accord/Prelude Honda Accord/Prelude 1984-1995 In Tank Fuel Pumps TEST 1. Turn the ignition OFF. 2. On the Accord, remove the screws securing the underdash fuse box to its mount. Remove the fuel cut off relay from the

More information

DESCRIPTION. Chrysler NCV3 Service Info Section 08 > Electronic Modules > MODULE, Transmission Control Information

DESCRIPTION. Chrysler NCV3 Service Info Section 08 > Electronic Modules > MODULE, Transmission Control Information DESCRIPTION The transmission control module (TCM) receives, processes and sends various digital and analog signals related to the automatic transmission. In addition, it processes information received

More information

Troubleshooting Guide for Okin Systems

Troubleshooting Guide for Okin Systems Troubleshooting Guide for Okin Systems More lift chair manufacturers use the Okin electronics system than any other system today, mainly because they re quiet running and usually very dependable. There

More information

Servo and Proportional Valves

Servo and Proportional Valves Servo and Proportional Valves Servo and proportional valves are used to precisely control the position or speed of an actuator. The valves are different internally but perform the same function. A servo

More information

CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS

CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS ZG CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS page GENERAL INFORMATION OVERVIEW... 1 DESCRIPTION AND OPERATION BATTERY TEMPERATURE SENSOR... 2 CHARGING SYSTEM OPERATION... 1 ELECTRONIC VOLTAGE REGULATOR...

More information

E4OD/4R100. Check Ball Identification and Symptom Chart. Early 1989 E4ODs The first E4OD had 16 checkballs.

E4OD/4R100. Check Ball Identification and Symptom Chart. Early 1989 E4ODs The first E4OD had 16 checkballs. 110 FORD Check Ball Identification and Symptom Chart Repeated failures are caused by only two types of problems: parts or technique. If a part is causing the failure, it should be no surprise that using

More information

Torque Convertor Control System

Torque Convertor Control System 1 BD AutoLoc Torque Convertor Control System Part# 1030390 Installation Manual for the following applications: BD Brakes for Dodge, Ford and Chevrolet Pac Brake for Dodge & Ford Jacobs E-Brake for 1994-98

More information

chart for this unit. Let s look at some of the gear

chart for this unit. Let s look at some of the gear by David Skora recently began seeing a new 6- speed automatic transmission in some Beetle and Passat vehicles. Built by Aisan, this transmission uses the Leppeletier planetary design. All shift timing

More information

What is it that makes that. LET S PLAY BALL Time to Shift Gears. by Lance Wiggins. Typical 4 Speed Mitsubishi

What is it that makes that. LET S PLAY BALL Time to Shift Gears. by Lance Wiggins. Typical 4 Speed Mitsubishi LET S PLAY BALL Time to Shift Gears Typical 4 Speed Mitsubishi by Lance Wiggins What is it that makes that grinding noise in my transmission? I just had it serviced and that noise started shortly after

More information

Surge Brake Troubleshooting Tips

Surge Brake Troubleshooting Tips Surge Brake Troubleshooting Tips Surge Brake Troubleshooting Tips Think Safety!! Don t attempt working on your brakes if you aren t experienced with brake systems. These troubleshooting tips assume a person

More information

Parts Interchange, and Immediate Failure after Rebuild

Parts Interchange, and Immediate Failure after Rebuild LET'S PLAY BALL 4L60/65/70E: Parts Interchange, and Immediate Failure after Rebuild by Lance Wiggins Sometimes parts interchanges can be the death of you whether it s about the cost, the headache, or the

More information

In the previous article we discussed KEEP THOSE TRANNYS ROLLING. P codes indicate an Engine Performance System or Transmission System problem.

In the previous article we discussed KEEP THOSE TRANNYS ROLLING. P codes indicate an Engine Performance System or Transmission System problem. KEEP THOSE TRANNYS ROLLING The NVG246 Transfer Case, Part 2: System Diagnosis and Repair by Pete Huscher The first place to start with any diag- nosis is to duplicate the symptom. If you can t duplicate

More information

Tuning A Walbro Carb. Walbro Carb TUNE UP & Illustrated Guide

Tuning A Walbro Carb. Walbro Carb TUNE UP & Illustrated Guide Tuning A Walbro Carb Walbro Carb TUNE UP & Illustrated Guide by M. B. Fuess Walbro carbs aren t too difficult to tune up if you know what you re doing. First of all, you need to know how the carb works

More information

Which one? All are capable of doing the job

Which one? All are capable of doing the job TM9-4910-509-10 Which one? All are capable of doing the job Now is the time to get it off the shelf and get acquainted with it. The LVCT can make you a topnotch vehicle electrical troubleshooter It s a

More information

TRANSMISSION PARTS Instructions. Solenoid Regulator Valve Retainer Shim. Main Pressure Regulator Valve

TRANSMISSION PARTS Instructions. Solenoid Regulator Valve Retainer Shim. Main Pressure Regulator Valve TRANSMISSION PARTS Instructions Sure Cure Kit Part No. SC-AODE NOTE: This kit is fully compatible with '91 '95 only. Identified by alignment pins 13mm heads. This kit will not work on '96 Later units.

More information

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved DRM TM DRM-HP TM Electronic Dynamo Regulator INSTRUCTION MANUAL COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved INTRODUCTION The Clover Systems DRM is a state-of-the art all-electronic voltage and current

More information

JATCO RE5R05A. Figure 1

JATCO RE5R05A. Figure 1 LET'S PLAY BALL Controlling the JATCO RE5R05A Part 2 of 3 by Lance Wiggins So you re back for more good. In this issue of GEARS, we re going to go through the valve body, TCM and solenoids of the JATCO

More information

GM 4L80-E, 4L85-E SURE CURE KIT

GM 4L80-E, 4L85-E SURE CURE KIT GM 4L80-E, 4L85-E SURE CURE KIT PART NUMBER SC-4L80E INSTALLATION GUIDE Parts are labeled here in order of installation. See page 2 for details on Sure Cure kit contents. See Sure Cure instruction booklet

More information

AODE ( 96 & LATER) SC-AODE-1. Transmission Reconditioning Kit FULL COMPATIBILITY IMPORTANT VALVE BODY PARTS REASSEMBLY PARTS

AODE ( 96 & LATER) SC-AODE-1. Transmission Reconditioning Kit FULL COMPATIBILITY IMPORTANT VALVE BODY PARTS REASSEMBLY PARTS AODE ( 96 & LATER) Transmission Reconditioning Kit FULL COMPATIBILITY SC-AODE-1 Full compatibility with 1996 and later units. Identified by alignment pins with 10mm head and.173" pin diameter. IMPORTANT

More information

4L80E Updates. Transmission: Subject: Application: Issue Date: Chevrolet L80E. Updates ACTUATOR FEED LIMIT FLUID SPOOL VALVE SPRING

4L80E Updates. Transmission: Subject: Application: Issue Date: Chevrolet L80E. Updates ACTUATOR FEED LIMIT FLUID SPOOL VALVE SPRING Transmission: Subject: Application: Issue Date: Technical Bulletin #266 4L80E Updates Chevrolet 1995 4L80E Updates Many electrical changes have occurred in the 4L80E transmission for the 1994 model year,

More information

BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines

BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines BSR BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines Features Digital Advance The main feature of the Magic Box is the digital advance that replaces conventional weights and springs.

More information

STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS

STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS TJ STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS page DESCRIPTION AND OPERATION STARTER MOTOR... 2 STARTER RELAY... 3 STARTING SYSTEM... 1 DIAGNOSIS AND TESTING STARTER MOTOR... 8 STARTER MOTOR NOISE

More information

Dealing with customer concerns related to electronic throttle bodies By: Bernie Thompson

Dealing with customer concerns related to electronic throttle bodies By: Bernie Thompson Dealing with customer concerns related to electronic throttle bodies By: Bernie Thompson In order to regulate the power produced from the gasoline internal combustion engine (ICE), a restriction is used

More information

MSD 7AL-3, Ignition Control PN 7230

MSD 7AL-3, Ignition Control PN 7230 MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,

More information

Photoillustration: Harold A. Perry; images: Thinkstock & Ford

Photoillustration: Harold A. Perry; images: Thinkstock & Ford 30 March 2014 WHAT S NEW IN EVAP Photoillustration: Harold A. Perry; images: Thinkstock & Ford TESTING BY BOB PATTENGALE Automotive technology evolves. Changes may improve the ownership experience or allow

More information

by Steve Garrett for operating tools and appliances.

by Steve Garrett for operating tools and appliances. The Shock of SPEAKER Your Life, PART 1 by Steve Garrett As we re all aware, changes in the automotive industry are occurring at an alarming rate. The pressure on OEMs to meet changes in the federal fuel

More information

Driving a vehicle with the Lightning Hybrids Energy Recovery System JUNE 2016

Driving a vehicle with the Lightning Hybrids Energy Recovery System JUNE 2016 Driving a vehicle with the Lightning Hybrids Energy Recovery System JUNE 2016 Welcome to Lightning Hybrids Driver Training Lightning Hybrids hydraulic hybrid system saves fuel and reduces emissions. It

More information

RE5R05A. A Last Look at the. Welcome back to the final part in our series covering. Part 3 of 3 LET'S PLAY BALL. by Lance Wiggins

RE5R05A. A Last Look at the. Welcome back to the final part in our series covering. Part 3 of 3 LET'S PLAY BALL. by Lance Wiggins LET'S PLAY BALL A Last Look at the RE5R05A Part 3 of 3 by Lance Wiggins Figure 1 Welcome back to the final part in our series covering the JATCO RE5R05A transmission. So far, we ve covered the computer

More information

GM 4L60-E, 4L65-E, 4L70-E Vacuum Test Plate Kit

GM 4L60-E, 4L65-E, 4L70-E Vacuum Test Plate Kit Vacuum Test Plate Kit PART NUMBER 77754-VTP INSTRUCTION BOOKLET Alignment Hole Key Red = Alignment Pins Black = Push Pin Locations Blue = Optional Bolt Locations 2017 Sonnax Industries, Inc. 77754-VTP-IN

More information

Troubleshooting A Vintage Distributor Ignition System

Troubleshooting A Vintage Distributor Ignition System Troubleshooting A Vintage Distributor Ignition System -Henry P. Olsen When the owners of vintage carburetor- and distributor-equipped vehicles see that a shop has a big-box engine analyzer, they believe

More information

Throttle Setup by Jason Priddle

Throttle Setup by Jason Priddle Throttle Setup by Jason Priddle This article is written around JR Radio convention. The numbers noted are for illustrative purposes, and the same principles apply to all radios Ever feel like all your

More information

RELEASING PRESSURE IN THE HYDRAULIC SYSTEM,

RELEASING PRESSURE IN THE HYDRAULIC SYSTEM, Testing And Adjusting Introduction NOTE: For Specifications with illustrations, make reference to SPECIFICATIONS for 225 EXCAVATOR HYDRAULIC SYSTEM, Form No. SENR7734. If the Specifications are not the

More information

Late Model Honda. Remember when you had a FUN WITH TRANSMISSIONS

Late Model Honda. Remember when you had a FUN WITH TRANSMISSIONS FUN WITH TRANSMISSIONS Late Model Honda by Bill Brayton Today s late model Accords have changed; removing the unit from the car isn t always necessary to correct a shift problem. Remember when you had

More information

Roehrig Engineering, Inc.

Roehrig Engineering, Inc. Roehrig Engineering, Inc. Home Contact Us Roehrig News New Products Products Software Downloads Technical Info Forums What Is a Shock Dynamometer? by Paul Haney, Sept. 9, 2004 Racers are beginning to realize

More information

Honda Accord. Maintenance Schedule ebook Lake Worth Rd., Greenacres, FL BramanHondaPB.com

Honda Accord. Maintenance Schedule ebook Lake Worth Rd., Greenacres, FL BramanHondaPB.com Honda Accord Maintenance Schedule ebook 5200 Lake Worth Rd., Greenacres, FL 33463 BramanHondaPB.com 561-790-8570 BramanHondaPB.com 561-790-8570 1 Just as you would visit the doctor s office every year

More information

Solutions to Common Problems

Solutions to Common Problems TECH-BRIEF by Larry Frash Solutions to Common Problems CD4E: Oil out of the vent. The 94-96 CD4E side cover originally came with a vent that was located too close to the solenoid body (figure 1). With

More information

FORD 6R80 UPDATES Presented by: David Chalker ATRA Technical Advisor 6R80

FORD 6R80 UPDATES Presented by: David Chalker ATRA Technical Advisor 6R80 FORD UPDATES Presented by: David Chalker ATRA Technical Advisor Welcome To Today s Presentation Sponsored By: Any Questions Or Comments Please Send Emails To webinars@atra.com Any Questions That You

More information

Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT

Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT PART NUMBER SC-46-47RHE-OS INSTALLATION GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Sure Cure kit contents.

More information

GM 4L80-E, 4L85-E SURE CURE KIT

GM 4L80-E, 4L85-E SURE CURE KIT GM 4L80-E, 4L85-E SURE CURE KIT PART NUMBER SC-4L80E INSTRUCTION BOOKLET Parts are labeled here in order of installation. See page 2 for details on Sure Cure kit contents. See Sure Cure instruction booklet

More information

Technical Bulletin Listing 2009

Technical Bulletin Listing 2009 Technical Bulletin Listing 2009 May, 2009 Transmission Bulletin # # Pages Subject January U140E/U241E 1225 1 Harsh 2-3 Shift After Overhaul GM MP T-Case 1226 10 Introduction 6T70/75 1227 1 Transfer Bolt

More information

Technical Bulletin Listing 2010

Technical Bulletin Listing 2010 Technical Bulletin Listing 2010 January, 2010 Transmission Bulletin # # Pages Subject January Allison LCT 1000 1300 1 Sets P0872, No 4th, 3rd Gear Start 4L80E 1301 4 Shift Shuttle/No Line Rise RE4F04A

More information

HWH Online Technical School Lesson 10: Air Suspension and HWH (Filename: ML DOC Revised: 23APR16) Click Here for Printable PDF File

HWH Online Technical School Lesson 10: Air Suspension and HWH (Filename: ML DOC Revised: 23APR16) Click Here for Printable PDF File CHAPTER 1 - Preface HWH Online Technical School Lesson 10: Air Suspension and HWH (Filename: ML57000-018.DOC Revised: 23APR16) Click Here for Printable PDF File CHAPTER 2 - Hydraulic Leveling and Air Suspensions

More information

Fuel System (Central SFI)

Fuel System (Central SFI) Page 1 of 6 1997 GMC Truck GMC K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Engine Engine Controls - 5.0L, 5.7L, and 7.4L Description and Operation Document

More information

Series circuits. The ammeter

Series circuits. The ammeter Series circuits D o you remember how the parts of the torch on pages 272 3 were connected together? The circuit contained several components, connected one after the other. Conductors, like the metal strip

More information

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved DRM TM DRM-HP TM Electronic Dynamo Regulator INSTRUCTION MANUAL COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved INTRODUCTION The Clover Systems DRM is a state-of-the art all-electronic voltage and current

More information

2/24/ K Excessive Parasitic Draw? Check If the B-CAN System Is Awake 2006 Honda Ridgeline MotoLogic. ServiceNews Article

2/24/ K Excessive Parasitic Draw? Check If the B-CAN System Is Awake 2006 Honda Ridgeline MotoLogic. ServiceNews Article ServiceNews Article July 2008 Helping you fix it right the first time - every time Excessive Parasitic Draw? Check If the B-CAN System Is Awake Currently Applies To: All models equipped with the B-CAN

More information

Once in a while an opportunity

Once in a while an opportunity Once in a while an opportunity comes along that compels you to share your experiences with others dealing with the same issues. In this case we had a number of issues with a late Volkswagen Beetle and

More information

70 psi x 1 sq. in. = 70 lbs of force 70 psi x 9 sq. in. = 630 lbs of force. Figure 1 Figure 2

70 psi x 1 sq. in. = 70 lbs of force 70 psi x 9 sq. in. = 630 lbs of force. Figure 1 Figure 2 BASIC HYDRAULICS What is Pressure? In hydraulics, it can be defined as force applied uniformly over a contained area and is measured in force per unit of area. by Larry Frash 70 psi x 1 sq. in. = 70 lbs

More information

Nissan GTR Alpha Fuel System

Nissan GTR Alpha Fuel System Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs

More information

Installation Manual for Dodge 24V Cummins Version 3.1. Please read all instructions before the installation of the ATS Co-Pilot

Installation Manual for Dodge 24V Cummins Version 3.1. Please read all instructions before the installation of the ATS Co-Pilot 10/1/12 601-900-2218-INST Installation Manual for 1998.5-2002 Dodge 24V Cummins Version 3.1 Please read all instructions before the installation of the ATS Co-Pilot Thank you for purchasing the ATS Co-Pilot

More information

Fuel System Diagnosis

Fuel System Diagnosis 1996 Chevrolet Impala Caprice, Impala, Roadmaster (VIN B) Service Manual Engine Engine Controls - 4.3L (Caprice Only) and 5.7L Diagnostic Information and Procedures Document ID: 37723 Fuel System Diagnosis

More information

A/C Generator Systems

A/C Generator Systems A/C Generator Systems What is the function of the charging system? Provide power for all electrical loads Recharge the starting battery What happens if the charging systems puts out too much power? Voltage

More information

by David Skora These pressure readings are based on the computer reacting to the load conditions of the vehicle. Pressures may vary

by David Skora These pressure readings are based on the computer reacting to the load conditions of the vehicle. Pressures may vary Looking inside the Volkswagen 09G 6-Speed; Part 3 Looking inside the Volkswagen 09G 6-Speed; by David Skora PART 3 I n past issues we looked at the design and operation of the VW 6-speed transmission.

More information

TONY S TECH REPORT. Basic Training

TONY S TECH REPORT. Basic Training TONY S TECH REPORT (Great Articles! Collect Them All! Trade them with your friends!) Basic Training OK YOU MAGGOTS!! Line up, shut up, and listen good. I don t want any of you gettin killed because you

More information

Technical Bulletin # 1251

Technical Bulletin # 1251 Transmission: Subject: Application: Issue Date: CD4E TCC Slip Code Diagnosis Ford, Mercury and Mazda May 2009 CD4E TCC Slip Code Diagnosis Once the check engine light illuminates, the transmission will

More information

Troubleshooting Guide for Dewert Systems

Troubleshooting Guide for Dewert Systems Troubleshooting Guide for Dewert Systems Dewert electronics aren t as common as Okin systems as they re mainly used by one manufacturer (Pride). However, Pride is the largest lift chair manufacturer in

More information

4 Wire Wide Band Oxygen Sensors by Jim Gilmour Blue Print Technical Consultant

4 Wire Wide Band Oxygen Sensors by Jim Gilmour Blue Print Technical Consultant 4 Wire Wide Band Oxygen Sensors by Jim Gilmour Blue Print Technical Consultant Blue Print Technical Consultant Jim Gilmour, takes a look at 4 Wire Wide Band Oxygen Sensors, how they work and how to correctly

More information

The Life of a Lifter, Part 2

The Life of a Lifter, Part 2 Basics Series: The Life of a Lifter, Part 2 -Greg McConiga Last time we looked at some complicated dynamics and compared flats to rollers. Now for the hands-on. 6 FEATURE This off-the-shelf hydraulic lifter

More information

Before we get started, it s

Before we get started, it s Let s Play Ball with the Nissan s RE5F22A LET'S PLAY BALL Understanding the Diagnostics for SPEAKER Nissan s RE5F22A 5-Speed by Lance Wiggins Before we get started, it s important to understand that World

More information

I ve had lots of requests recently for

I ve had lots of requests recently for The right picture can be worth a thousand words. Here, circuit diagrams and oscilloscope patterns aid in visualizing the effects of resistance at two locations in a series circuit. Mark Warren smwarren@motor.com

More information

ZF4HP16. Technical Bulletin # Signal Combination L1 L2 L3 L4 P R N D

ZF4HP16. Technical Bulletin # Signal Combination L1 L2 L3 L4 P R N D Transmission: Subject: Application: Issue Date: Technical Bulletin # 1308 ZF4HP16 Electronical Components Description 2005 Suzuki Forenza L4-2.0L February, 2010 ZF4HP16 Electronical Components Description

More information

TEST CHART. Voltage Supply

TEST CHART. Voltage Supply ALL MEASUREMENTS ARE MADE ON THE TERMINALS OF THE DISCONNECTED WIRING HARNESS PLUG TO THE CONTROL UNIT (ECU) WITH IGNITION OFF UNLESS OTHERWISE INDICATED. Voltage Supply Ignition Voltage supply to the

More information

AISIN AW 60-41SN (AF-17)

AISIN AW 60-41SN (AF-17) AISIN AW 60-41SN (AF-17) zip Kit PaRT NUMBER AW60-41SN-ZIP Installation & TESTING BOOKLET Torque Specifications Manual Shaft Detent Spring Bolt 89 in-lb Manual Shift Shaft Retaining Nut 61 in-lb Transmission

More information

INSTRUCTIONS. #82028 Diesel Nitrous System. Thank you for choosing ZEX products; we are proud to be your manufacturer of choice.

INSTRUCTIONS. #82028 Diesel Nitrous System. Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. 1 INSTRUCTIONS #82028 Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Why our nitrous system is better: 2 Performance enthusiasts know the potential

More information

Understanding the Modern Automotive Air Conditioning System. Trainer: Grant Hand

Understanding the Modern Automotive Air Conditioning System. Trainer: Grant Hand Understanding the Modern Automotive Air Conditioning System Trainer: Grant Hand AUTOMOTIVE TRAINING SOLUTIONS PTY LTD Training for the future... Automotive Training Solutions IMPORTANT NOTE Copyright The

More information

4 fuel-efficient driving

4 fuel-efficient driving 4 fuel-efficient driving This chapter focuses on fuel-efficient driving techniques for large dieselpowered commercial vehicles. Many of these techniques can also be applied to smaller commercial vehicles

More information

BATTERY DISCONNECT SERVICE MANUAL

BATTERY DISCONNECT SERVICE MANUAL Battery Disconnect provides a simple and safe means of remotely disconnecting batteries of an RV or boat. With a touch of a remote switch, the batteries will be completely disconnected, preventing unwanted

More information

In the last issue of GEARS, we

In the last issue of GEARS, we Shortcuts to GM Solenoid Electrical Diagnosis, i s, Part 2 by Steve Garrett In the last issue of GEARS, we looked at the theory behind GM s transmission solenoid control systems. This time, we ll examine

More information

The Borg Warner Overdrive

The Borg Warner Overdrive The Borg Warner Overdrive by Tom Endy For the Model A Ford: Over the last 30 years the addition of an overdrive to a Model A Ford drive train has become a popular and practical convenience. The very first

More information

A device that measures the current in a circuit. It is always connected in SERIES to the device through which it is measuring current.

A device that measures the current in a circuit. It is always connected in SERIES to the device through which it is measuring current. Goals of this second circuit lab packet: 1 to learn to use voltmeters an ammeters, the basic devices for analyzing a circuit. 2 to learn to use two devices which make circuit building far more simple:

More information

A4BF2/A4AF3. It s Monday morning: A. Problems Before. and After Rebuild. No Forward in Drive; Manual Low and Reverse Okay.

A4BF2/A4AF3. It s Monday morning: A. Problems Before. and After Rebuild. No Forward in Drive; Manual Low and Reverse Okay. A4BF2/A4AF3 Problems Before SPEAKER and After Rebuild by Mike Souza It s Monday morning: A customer arrives at your shop in a 2000 Elantra and a harsh 4-3 coastdown and kickdown shift complaint. It uses

More information

FAULT CLASSIFICATION & TEST SELECTION Resisted Short to Ground

FAULT CLASSIFICATION & TEST SELECTION Resisted Short to Ground Ford Five Hundred No HVAC & Lack of Power A 2005 Ford Five Hundred came in to a shop with complaints of no A/C system operation and low engine power. The technician noted low refrigerant high side pressure

More information

TCI TRANS-SCAT

TCI TRANS-SCAT Page 1 of 9 Return to Instruction Sheet index TCI 360000 TRANS-SCAT Installation Instructions for FORD C-6 Transmissions TCI s TRANS-SCAT kit will allow you to calibrate the performance of your transmission.

More information

2001 Cougar Workshop Manual

2001 Cougar Workshop Manual Page 1 of 7 SECTION 303-06: Starting System 2001 Cougar Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 09/14/2001 Starting System Refer to Wiring Diagrams Section 303-06 for schematic and

More information

Advanced Auto Tech Worksheet Auto Trans & Transaxle Chapter 40 Pages Points Due Date

Advanced Auto Tech Worksheet Auto Trans & Transaxle Chapter 40 Pages Points Due Date Advanced Auto Tech Worksheet Name Auto Trans & Transaxle Chapter 40 Pages 1173 1215 107 Points Due Date 1. Automatic transmissions are operated by hydraulics as well as electronics to select according

More information

CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS

CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS TJ CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS page DESCRIPTION AND OPERATION BATTERY TEMPERATURE SENSOR... 2 CHARGING SYSTEM OPERATION... 1 ELECTRONIC VOLTAGE REGULATOR... 2 GENERATOR... 1 DIAGNOSIS

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1993 Mitsubishi Montero 1993 ACCESSORIES & EQUIPMENT Mitsubishi Cruise Control Systems Montero DESCRIPTION & OPERATION The cruise control system is electronically and vacuum controlled.

More information

The All-New BIG97 Tri-Power. In Detail.

The All-New BIG97 Tri-Power. In Detail. The All-New BIG97 Tri-Power. In Detail. The all-new Stromberg BIG97. On the outside, it s Genuine 97 all the way. But on the inside, we re talking 250cfm, new improved fuel circuits, ported distributor

More information