Parts and Accessories Installation Instructions

Transcription

1 Parts and Accessories Installation Instructions connector retrofit for external audio sources BMW Series (E 46), 5 Series (E 9) from 9/ X5 (E 5) from / These installation instructions are only valid for cars with SA 6/69/66+65 from 9/ Important information Subject to technical modifications. Target group These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies. In any event the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. Installation information Ensure that the cables/lines are not kinked or damaged as you install them in the car. The installed cables are to be secured with cable ties. Installation time Approx.,5 hours, but this may vary depending on the condition of the car and the equipment in it. Pictograms denotes instructions that draw your attention to special features. denotes the end of the instruction or caution text. List of special equipment The following special equipment must be taken into consideration when installing the retrofit kit. The various sections contain corresponding information. SA 6 On-board monitor SA 69 Navigation system SA BMW Business radio with CD drive Retrofit kit No

2 Special tools required E46 installation wedge ( 9 ) E9 radio puller (65 ) Special E46 radio tool (65 ) for SA 6 only EN/

3 Contents Section Page. Preparations Parts list To install and connect the AUX connector wiring harness in E46 cars To install and connect the AUX connector wiring harness in E9 cars To install and connect the AUX connector wiring harness in E5 cars Concluding work and coding Circuit diagram EN/

4 . Preparations TIS instruction No. Conduct a brief test Disconnect the negative pole of the battery... The following components must be removed first of all: Glove compartment on the right Radio receiver (cars with SA only) 65 Multi Information Display (E9/E5 cars with SA only) 65 8 On-board monitor (cars with SA 6/69 only) 65 5 EN/4

5 . Parts list E46 with SA only A D E F G 46 5 Z E9/E5 with SA only B D E F 46 6 Z E9/E46/E5 with SA 6/69 only C D E F 46 7 Z Legend A E46 AUX wiring harness with SA B E9/E5 AUX wiring harness with SA C E46/E9/E5 AUX wiring harness with SA 6/69 D Mounting plate E Philips screw (x) F Cable tie (5x) G Locking bar (E46 with SA only) EN/5

6 . Connection diagram E46 with SA only A A A 46 8 Z Item Description Signal Cable colour / Crosssection Connection location in the car Abbreviation / Slot A AUX connector wiring harness E46 with SA only --- A Pawl socket.5 mm In glove compartment --- A -pin GR socket casing To radio plug X86 X885 E9/E5 with SA only B B B 46 9 Z Item Description Signal Cable colour / Crosssection Connection location in the car Abbreviation / Slot B AUX connector wiring harness E9/E5 with SA only --- B Pawl socket.5 mm In glove compartment --- B SW -pin socket casing To radio plug X86 X598 E9/E46/E5 with SA 6/69 only C C C 46 Z Item Description Signal Cable colour / Crosssection Connection location in the car Abbreviation / Slot C AUX connector wiring harness E9/E46/E5 with SA 6/69 only --- C Pawl socket.5 mm In glove compartment --- C SW -pin plug casing To plug X48 X48 EN/6

7 . To install and connect the AUX connector wiring harness in E46 cars All holes must be drilled precisely as shown in the illustration. Drill a hole () in the rear of the glove compartment () with an 8 mm twist drill bit. Drill the holes () using a mm twist drill bit Z Insert branch A/C in the glove compartment () and secure it to the mounting plate D with a knurled nut (). A/C D Secure the mounting plate D to the glove compartment () using Philips screws E. E 46 5 Z Drill a hole () in the trim () with a mm twist drill bit through which you can thread the AUX connector wiring harness. Dimension a 4 mm Dimension b 45 mm b Enlarge the hole () to a diameter of mm. a 46 6 Z X86 Cars with SA only Connect branch A to plug X86 and secure it with the locking bar G. G A 46 Z EN/7

8 . To install and connect the AUX connector wiring harness in E46 cars X48 C Cars with SA 6/69 only Connect branch C to tied back plug X48. AUTO 46 7 Z EN/8

9 4. To install and connect the AUX connector wiring harness in E9 cars All holes must be drilled precisely as shown in the illustration. Drill a hole () in the rear of the glove compartment () with an 8 mm twist drill bit. Drill the holes () using a mm twist drill bit Z Insert branch B/C in the glove compartment () and secure it to the mounting plate D with a knurled nut (). B/C Secure the mounting plate D to the glove compartment () using Philips screws E. E D 9 58 Z X86 Cars with SA only Connect branch B to plug X86. B If the plug X is already in the car, the cables from branch B must be disconnected and connected to the same pins in the plug in the car X. 9 Z Cars with SA 6/69 only X48 C Connect branch C to tied back plug X Z EN/9

10 5. To install and connect the AUX connector wiring harness in E5 cars All holes must be drilled precisely as shown in the illustration. Drill a hole () in the trim () through the rear of the glove compartment with an 8 mm twist drill bit. Open the glove compartment and enlarge the hole () to a diameter of mm Z Insert branch B/C in the glove compartment () and secure it to the mounting plate D with a knurled nut (). B/C Mark the mounting holes and drill them with a mm twist drill bit. Secure the mounting plate D to the glove compartment () using Philips screws E. D E 5 9 Z X86 Cars with SA only Connect branch C to plug X86. C If the plug X is already in the car, the two cables from branch C must be disconnected and connected to the same pins in the plug in the car X. 9 Z X48 C Cars with SA 6/69 only Connect branch C to tied back plug X Z EN/

11 6. Concluding work and coding This retrofit system does not require coding. - Connect battery - Conduct a brief test with DIS/GT - To conduct a function test - Connect an external audio source to the pawl socket in the glove compartment - Press the "MODE" button several times until "AUX" appears in the display - Start the playback of the external audio source The volume and sound settings can be adjusted using the radio. If traffic bulletins from the radio have been activated, the audio signals from the external audio source will be interrupted when any such bulletins are broadcast. - Re-assemble the car EN/

12 7. Circuit diagram E46 with SA only A WS/BL,5 WS/GE,5 WS/BR,5 C=,µF Audio-R+ R=kΩ Audio-L+ C=,µF Audio-GND X Z E9/E5 with SA only B WS/BL,5 WS/GE,5 WS/BR,5 C=,µF Audio-R+ R=kΩ Audio-L+ C=,µF Audio-GND 4 X Z E9/E46/E5 with SA 6/69 only C WS/BL,5 WS/GE,5 WS/BR,5 C=,µF Audio-R+ R=kΩ Audio-L+ C=,µF Audio-GND X Z Legend A X885 B X598 C X48 Pawl plug.5 mm -pin GR socket casing Pawl plug.5 mm SW -pin socket casing Pawl plug.5 mm SW -pin plug casing Cable colours BL BR GE GR SW WS blue brown yellow grey black white EN/