MODEL 1200LB 1200 POUND MAGNETIC LOCK WITH LED, BOND SENSOR & DOOR STATUS SENSOR
|
|
- Helena Page
- 5 years ago
- Views:
Transcription
1 MODEL 1200LB 1200 POUND IC LOCK WITH LED, BOND SENSOR & STATUS SENSOR U.L. LISTED, LISTING NUMBER R POUND MINIMUM HOLDING FORCE SIZE: 10-1/2 L x 2-7/8 H x 1-1/2 W SIZE: 7-3/8 L x 2-3/8 W x 9/16 D 12 OR 24 VOLTS DC, JUMPER SELECTABLE VDC, VDC BI-COLOR LED, S.P.D.T. 3A. RELAY CONTACTS VDC, VDC SIGNALS A POWERED & SECURELY SEALED CLEAR ANODIZED U.S. 28 FINISH STANDARD DURONIC US 40 FINISH AVAILABLE ALARM CONTROLS CORPORATION 19 BRANDYWINE DRIVE DEER PARK, NY INFO@ALARMCONTROLS.COM
2 IC LOCK INSTALLATION INSTRUCTIONS PLEASE READ BEFORE INSTALLATION ALARM CONTROLS CORPORATION OFFERS A COMPLETE LINE OF IC LOCKS AND ACCESSORY ITEMS TO ASSIST THE INSTALLER IN MANAGING EVERY APPLICATION. THE IC LOCK IS DESIGNED TO MOUNT TO THE FRAME ON THE STOP SIDE OF THE IN A TYPICAL OUTSWINGING INSTALLATION,(SEE PAGE 2 FOR INSWINGING INSTALLATION). SUFFICIENT HEADER SPACE MUST BE AVAILABLE TO MOUNT THE IC LOCK TO INSURE A SAFE AND SECURE INSTALLATION. 1. NOTE TYPE OF FRAME HEADER AND INSTALL FILLER OR ANGLE BRACKET AS REQUIRED TO PROVIDE A FLAT MOUNTING SURFACE ON THE HEADER THE ENTIRE LENGTH OF THE IC LOCK. OUTSWINGING INSTALLATION HEADER FILLER HEADER HEADER HEADER ANGLE BRACKET OUT SWINGING SOLID OUT SWINGING OUT SWINGING 2. FOLD TEM ON DOTTED LINE TO FORM A 90 DEGREE ANGLE. TAPE TEM AGAINST HEADER WITH IN A CLOSED POSITION 1 FROM FRAME OPPOSITE HINGE SIDE OF JAMB. FOR A PAIR OF DOUBLE S PLACE TEM AT THE CENTER OF THE OPENING. TRANSFER HOLE LOCATIONS TO AND FRAME HEADER, (SEE TEM INSTRUCTIONS). 3. FOLLOW TEM INSTRUCTIONS FOR HOLE SIZES. USE THE ILLUSTRATIONS BELOW TO DETERMINE THE PROPER HOLE PREPARATION FOR THE ACCCORDING TO THE TYPE IN THE INSTALLATION. THE INCLUDED HARDWARE PACKAGE CONTAINS ALL NECESSARY ITEMS TO COMPLETE THE INSTALLATION. TO REMOVE THE HEADER INSERT HEX KEY INTO HOLES LOCATED AT THE BOTTOM OF LOCK ON THE RIGHT AND LEFT SIDE AND UN-SCREW THE CAP SCREWS HOLLOW STEP 2 FOLLOW WITH 1/2 DIA. HOLE THRU STEP 1 DRILL 1/4 DIA. HOLE THRU SIDE OF STEP 2 DRILL 1/2 DIA. HOLE THRU SEX BOLT SIDE OF STEP 1 DRILL 21/32 DIA. HOLE THRU SIDE OF ONE THICKNESS ONLY ONE THICKNESS ONLY MUST ROCK ON MUST ROCK ON ALARM CONTROLS CORPORATION 19 BRANDYWINE DRIVE P.O. BOX 280 DEER PARK, NY
3 INSWINGING INSTALLATION WITH L- Z BRACKET FRAME STEP 1 FASTEN THE L BRACKET ON THE FRAME IN A SUITABLE LOCATION. MOUNT THE IC LOCK TO THE L BRACKET. MAKE SURE THAT THE IC LOCK DOES NOT OBSTRUCT THE CLOSING OF THE. L BRACKET CONNECT THE CORRECT VOLTAGE TO THE. ADJUSTABLE Z BRACKET STEP 2 ASSEMBLE THE Z BRACKET WITH THE SOCKET HEAD CAP SCREWS PROVIDED. DO NOT TIGHTEN THE CAP SCREWS AT THIS TIME. THE Z BRACKET MUST BE ADJUSTABLE. BOLT RUBBER WASHER METAL WASHERS STEP 3 MOUNT THE TO THE ADJUSTABLE SECTION OF THE Z BRACKET WITH THE BOLT. DO NOT REMOVE THE RUBBER WASHER ATTACHED TO THE BOLT. USE ONE RUBBER WASHER BETWEEN TWO METAL WASHERS ON THE BOLT. THE WASHER ASSEMBLY MUST BE BETWEEN THE AND THE ADJUSTABLE SECTION OF THE Z BRACKET. APPLY THE SCREW LOCKING AGENT TO THE BOLT. DO NOT OVER TIGHTEN. MUST ROCK TO ALIGN WITH THE. ADJUSTABLE SECTION OF Z BRACKET WITH ATTACHED Z BRACKET ASSEMBLY STEP 4 CLOSE THE AND ALIGN THE TO THE AND APPLY POWER TO THE. LET THE BOND TO THE. BE SURE THE Z BRACKET ASSEMBLY IS FIRMLY AGAINST THE CLOSED. TIGHTEN THE CAP SCREWS HOLDING THE Z BRACKET ASSEMBLY. FASTEN THE Z BRACKET ASSEMBLY TO THE WITH THE SCREWS SUPPLIED. COMPLETED INSWINGING INSTALLATION STEP 5 CHECK THE COMPLETED ALIGNMENT AND INSTALLATION OF THE AND BY OPENING AND CLOSING THE BY ENERGIZING AND DE-ENERGIZING THE IC LOCK SEVERAL TIMES. THIS WILL INSURE THAT THE CORRECT OPERATION AND ALIGNMENT OF THE IC LOCK HAS BEEN PROPERLY INSTALLED.
4 IC LOCK L / Z BRACKETS FOR INSWINGING S AM2370 FOR 300 POUND IC LOCK AM3370 FOR ALL 600 POUND MODELS OF SINGLE IC LOCKS AM6370 FOR ALL 1200 POUND MODELS OF SINGLE IC LOCKS AM3375 FOR ALL 600 POUND MODELS OF DOUBLE IC LOCKS AM6375 FOR ALL 1200 POUND MODELS OF DOUBLE IC LOCKS IC LOCK CARE AND MAINTENANCE IC LOCKS HAVE NO INTERNAL MOVING PARTS AND REQUIRE A MINIMUM AMOUNT OF MAINTENANCE. IT IS RECOMMENDED THAT THE FACE OF THE AND BE WIPED CLEAN AND A L IGHT COATING OF A SUITABLE SILCONE LUBRICANT BE APPLIED TO EACH SURFACE TO PREVENT RUST ALTHOUGH THE MATING SURFACES HAVE BEEN D. THIS ONLY NEEDS TO BE DONE WHEN DIRT BUILD-UP IS NOTICED. THE BOLT AND THE HEX HEAD SCREWS HOLDING THE TO HEADER SHOULD BE CHECKED EVERY THREE MONTHS TO INSURE A SAFE AND SECURE INSTALLATION. IC LOCK ELECTRICAL SPECIFICATIONS 300 POUND MODEL SINGLE IC LOCK, VDC, VDC ALL 600 POUND MODELS OF SINGLE IC LOCK, VDC, VDC ALL 1200 POUND MODELS OF SINGLE IC LOCK, VDC, VDC ALL 600 POUND MODELS OF DOUBLE IC LOCKS, VDC, VDC, EACH LOCK ALL 1200 POUND MODELS OF DOUBLE IC LOCKS, VDC, VDC, EACH LOCK ALL IC LOCKS ARE SET AT THE FACTORY FOR 24 VDC TYPICAL IC LOCK WIRING POSITIVE FILTERED DC POWER SUPPLY N/C REX BUTTON DIGITAL KEYPAD PIR + - IC LOCK NEGATIVE
5 WIRE GAUGE CHART DISTANCE FROM POWER SUPPLY TO IC LOCK 12 VDC 24 VDC MA. D C 300 MA. C U R R E N T 400 MA. 600 MA. 800 MA. 8 GA. 1 AMP. 8 GA. TROUBLE SHOOTING GUIDE PROBLEM CAUSE SOLUTION LOCK BUZZES INSUFFICIENT HOLDING FORCE DOES NOT LOCK AC VOLTAGE CONNECTED TO LOCK AC RIPPLE IN POWER SUPPLY INCORRECT INPUT VOLTAGE LOW INPUT VOLTAGE MISALIGNMENT OF SCREWED TIGHT TO WRONG HARDWARE ASSEMBLY NO POWER TO SUPPLY DC VOLTAGE TO LOCK REPLACE POWER SUPPLY CHECK VOLTAGE JUMPER POSITION FOR CORRECT VOLTAGE SETTING LOCK SET AT FACTORY FOR 24 VDC CHECK POWER SUPPLY VOLTAGE WIRE GAUGE INCORRECT FOR WIRE RUN MUST COVER ALL IC POLES OF LOCK MUST ROCK ON TO ALIGN WITH LOCK A METAL WASHER,RUBBER WASHER AND METAL WASHER MUST BE BETWEEN AND CHECK POWER AT LOCK CHECK POWER SUPPLY CHECK ALL CONNECTIONS STATUS SENSOR NOT WORKING (APPLICABLE MODELS) IN NOT ALIGNED WITH LOCK ALIGN IN WITH STATUS SENSOR DOT ON LOCK
6 IC LOCK WIRING INSTRUCTIONS MODELS WITH BOND SENSOR & STATUS SENSOR 600LB, 600DLB, 1200LB, 1200D IMPORTANT ON ALL MODELS REMOVE TERMINAL COVER SCREW TO ACCESS HEADER MOUNTING SCREW BOND SENSOR V+ V- N/O COM N/C WIRING INSTRUCTIONS CONNECT POSITIVE LOCK POWER TO V+ TERMINAL CONNECT NEGATIVE LOCK POWER TO V+ TERMINAL P1 P2 OPERATION OF BOND SENSOR AND LED THE BOND SENSOR DETECTS WHEN THE IC LOCK IS POWERED AND IS CLOSED. OPEN, LOCK NOT POWERED: RELAY OFF LED OFF CLOSED, LOCK POWERED: RELAY ON LED GREEN CLOSED, LOCK NOT POWERED: RELAY OFF LED OFF OPEN, LOCK POWERED: RELAY OFF LED RED VOLTAGE SELECTION FOR 12 V FOR 24 V P1 P2 VOLTAGE IS FACTORY SET FOR 24 VDC ANTI-ROTATION PIN STATUS SENSOR BOLT HOLE ORIENTATION OF THE AND A B ANTI-ROTATION PIN PERMANENT INSTALL THE AND AS SHOWN. IF NOT POSITIONED AS SHOWN THE OPERATION OF THE SENSOR OUTPUT WILL BE AFFECTED. STATUS SENSOR THE STATUS SENSOR,(REED SWITCH), IS NORMALLY-OPEN. WHEN THE IS AGAINST THE THE CONTACTS ARE CLOSED. THE TWO WHITE/GREEN LEADS,(A,B),ARE FOR THE STATUS SENSOR. WHEN MOUNTING ON RUBBER WASHER MUST BE PLACED BETWEEN METAL WASHERS. DO NOT EXCESSIVLY TIGHTEN SEX BOLT. MUST FLOAT ON.THREAD LOCKING AGENT SHOULD BE USED. ALARM CONTROLS CORPORATION DEER PARK, NEW YORK PH: FAX: INFO@ALARMCONTROLS.COM WEBSITE:
MODEL 600LB 600 POUND SINGLE MAGNETIC LOCK WITH LED, BOND SENSOR & DOOR STATUS SENSOR SPECIFICATIONS
MODEL 600LB 600 POUND SINGLE MAGNETIC LOCK WITH LED, BOND SENSOR & STATUS SENSOR SPECIFICATIONS U.L. LISTED, LISTING NUMBER R16759 600 POUND MINIMUM HOLDING FORCE MAGNET SIZE 9-7/8 L x 1-11/16 H x1 W SIZE
More informationMODEL 1200S MAGNETIC LOCK
MODEL 1200S MAGNETIC LOCK SPECIFICATIONS U.L. LISTED, LISTING NUMBER R16759 1200 POUND MINIMUM HOLDING FORCE MAGNET SIZE 10-1/2 L x 2-7/8 H x1-1/2 W 12 OR 24 VOLT DC OPERATION, JUMPER SELECTABLE CURRENT
More informationMODEL 600S 600 POUND SINGLE MAGNETIC LOCK SPECIFICATIONS
MODEL 600S 600 POUND SINGLE MAGNETIC LOCK SPECIFICATIONS U.L. LISTED, LISTING NUMBER R16759 600 POUND MINIMUM HOLDING FORCE MAGNET SIZE 9-7/8 L x 1-11/16 H x1 W SIZE 5-1/2 L x 1-1/4 W x 7/16 D 12 OR 24
More informationMODEL 600LB 600 POUND SINGLE MAGNETIC LOCK WITH LED, BOND SENSOR & DOOR STATUS SENSOR SPECIFICATIONS
MODEL 600LB 600 POUND SINGLE MAGNETIC LOCK WITH LED, BOND SENSOR & STATUS SENSOR SPECIFICATIONS U.L. LISTED, LISTING NUMBER R16759 600 POUND MINIMUM HOLDING FORCE MAGNET SIZE 9-7/8 L x 1-11/16 H x1 W SIZE
More informationMODEL 1200S MAGNETIC LOCK
MODEL 1200S MAGNETIC LOCK SPECIFICATIONS U.L. LISTED, LISTING NUMBER R16759 1200 POUND MINIMUM HOLDING FORCE MAGNET SIZE 10-1/2 L x 2-7/8 H x1-1/2 W 12 OR 24 VOLT DC OPERATION, JUMPER SELECTABLE CURRENT
More informationV2M1200/1290 Series Maglock Installation Instructions
Securitron Phoenix, AZ 85044 Tel: 1-800-624-5625 Mon-Fri: 6:00am - 4:00pm PDT Fax: 1-800-232-7329 www.securitron.com V2M1200/1290 Series Maglock Installation Instructions 1 Table of Contents Product Information...
More informationINSTALLATION INSTRUCTIONS 1576DE DELAYED EGRESS EMLOCK
801 Avenida Acaso, Camarillo, Ca. 930 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS 1576DE DELAYED EGRESS EMLOCK PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED
More informationINSTALLATION INSTRUCTIONS E300 SERIES MAGNETIC CABINET/DISPLAY CASE LOCK
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS E300 SERIES MAGNETIC CABINET/DISPLAY CASE LOCK The E300 Series magnetic
More informationSecurity Door Controls
Security Door Controls 801 Avenida Acaso, Camarillo, ca. 930 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com 1575-1576 EMLOCK R INSTALLATION INSTRUCTIONS During installation,
More informationInstallation Instructions
I N S T A L L A T I O N 8310/8320 8330/8340 Electromagnetic Locks Pre-Installation Instructions 1. This product must be installed according to all applicable building and life safety codes. 2. Due to the
More information1-3/4" MOUNTING INSTRUCTIONS: 1150 SERIES SURFACE MOUNTED 1500 LB. ELECTROMAGNETIC LOCK
MOUNTING INSTRUCTIONS: 1150 SERIES SURFACE MOUNTED 1500 LB. ELECTROMAGNETIC LOCK FULL WIDTH STOP WITH SURFACE MOUNT ARMATURE Model Numbers: 1150, 1152 & 1155 READ THOROUGHLY BEFORE INSTALLING HEADER STOP
More information8. Do not install this product on the exterior of buildings. 9. Do not use as a doorstop. This will void warranty. Installation Instructions
INSTALLATION 8310-IQ/8320-IQ IntelliMag Electromagnetic Locks Pre-Installation Instructions 1. This product must be installed according to all applicable building and life safety codes. 2. Due to the variety
More informationINSTALLATION DESCRIPTION
The Series 2011xTJ20 / 3000LCxTJ20 is a 1200 pound holding force top jamb-mounted electromagnetic lock designed to secure a single-inswinging door. The lock requires both installation procedures as described
More informationHANDLING MECHANICAL INSTALLATION
2 INSTALLATION DESCRIPTION The and 2 Delay Egress Systems are 1500 pound holding force (holding force not evaluated by UL) per leaf electromagnetic locks, electronically controlled to provide a 15 or 30
More informationPre-Installation Instructions
BML-8371 and BML-8372 Electromagnetic Locks Spanish and French translations are available on www.bestaccess.com Traducciones al español y francés están disponibles en www.bestaccess.com Des traductions
More informationEMLock 1500 Series. MEA Listed
EMLock 1500 Series SDC s patented EMLock design represents the pinnacle of magnetic lock evolution. The modular EMLock assembly makes them easy to stock, install, upgrade and maintain. Patented SDC 1500
More informationINSTALLATION 8310/8320
INSTALLATION 8310/8320 Electromagnetic Locks Pre-Installation Instructions 1. This product must be installed according to all applicable building and life safety codes. 2. Due to the variety of mounting
More informationM670/M680BD MAGNALOCK SERIES Installation Instructions
Securitron www.securitron.com Tel 800.624.5625 techsupport@securitron.com M670/M680BD MAGNALOCK SERIES Installation Instructions Page 1 Rev. D, 12/14 Table of Contents Package Contents... 3 Mounting Hardware...
More information* * M400 Series. Features. Models. Trims. UL Requirements. Single Electromagnetic Locks: M420, M450, M490. Installation Instructions
*44487296* M400 Series 44487296 Single Electromagnetic Locks: M420, M450, M490 Installation Instructions M420/M450 Armature plate assembly M490 Armature plate assembly Features Automatic Voltage Selection
More informationINSTALLATION INSTRUCTIONS MINI EXIT CHECK DELAYED EGRESS EMLOCK 1581S
SECURITY DOOR CONTROLS 3580 Willow Lane, Westlake Village, CA 91361-4921 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS MINI EXIT CHECK
More informationWith LED, Bond Sensor E-941SA-600PQ 600-lb. (272kg) E-941SA-1K2PQ 1200-lb. (545kg) Weatherproof E-941SA lb.
Electromagnetic Lock E-941SA-600 600-lb. (272kg) E-941SA-1200 1200-lb. (545kg) With LED, Bond Sensor E-941SA-600PQ 600-lb. (272kg) E-941SA-1K2PQ 1200-lb. (545kg) Weatherproof E-941SA-300 300-lb. (136kg)*
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
More informationDynaLock 705 Emmett Street Bristol, CT Phone:(860) Fax:(860)
ELECTROMAGNETIC GATELOCK INSTALLATION INSTRUCTIONS PLEASE READ BEFORE INSTALLATION Familiarize yourself with the gate and post conditions prior to installation. The lock must rigidly mount to the gate
More informationInstallation Instructions for ROFU Key Hole Mount Magnetic Locks
ROFU For Outswing Doors Installation Instructions for ROFU Key Hole Mount Magnetic Locks 808-LC, 808-B, 8-LC, 8-B, 8--LC, 8--B, 8-099 *See page for model specifications 009 S. Tacoma Way, E- -800--768
More informationInstallation Instructions for Slide Mount Magnetic Locks
ROFU For Outswing Doors Installation Instructions for Slide Mount Magnetic Locks 8606, 8608 and 8612 Series *See page 2 for model specifications R Find the paper installation template included with the
More informationINSTALLATION EML375. Pre-Installation Instructions. Electromagnetic Locks
INSTALLATION EML375 Electromagnetic Locks Pre-Installation Instructions PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO THE END-USER UPON COMPLETION OF THE INSTALLATION. 1. This product must be installed
More informationACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-8 Features: ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS Filtered/Regulated 24 Volts DC Up to Full 2 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit
More informationPLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLING THE ELECTROMAGNETIC LOCK.
575 Birch Street, Forestville, CT 06010 Phone (866) 322-1237 Fax (866) 322-1233 WWW. LOCKNETICS.COM 390/390-2 DEL INSTALLATION AND PROGRAMMING 390DEL DELAYED EGRESS General Description... 2 Technical Specifications...
More informationPackage Contents. Mounting Hardware
Securitron Magnalock Corp. www.securitron.com Tel 800.624.5625 techsupport@securitron.com M680BDCX MAGNALOCK SERIES Installation Instructions Table of Contents Specifications 2 Configuring Options 3 Installation
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More information5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE
5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE MODEL# 505 ( AMP @ VDC OR 4VDC) MODEL# 5500 ( AMP @ VDC OR AMPS @ 4VDC) MODEL# 5600- (0 AMPS @ VDC) MODEL# 5600-4 (5 AMPS @ 4VDC) IMPORTANT SAFETY INSTRUCTIONS
More informationAL600ULX Series. Power Supply/Charger Installation Guide
AL600ULX Series Power Supply/Charger Installation Guide Models Include: AL600ULX - Single Output AL600ULPD4 AL600ULPD4CB - Four (4) Fused Outputs - Four (4) PTC Outputs AL600ULPD8 AL600ULPD8CB - Eight
More informationMagForce+ The Positive Force in Electromagnetic Locks
MagForce+ The Positive Force in Electromagnetic Locks 390+ 320+ 350+ The MagForce+ Family 390+ 320+ 350+ MADE IN THE USA MEA 11-95-E Locknetics new MagForce Plus generation of electromagnetic locks is
More informationMODEL 3002xTJ32 ELECTROMAGNETIC LOCK INSTALLATION INSTRUCTIONS
The Series 3002xTJ32 is a 1500 pound holding force top jamb mounted electromagnetic lock designed to secure a double inswing door. The lock requires both installation procedures as described herein and
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions
More informationE-941SA-300RQ. Manual. 300-lb Single-Door Electromagnetic Lock with Reversible Magnet
E-941SA-300RQ 300-lb Single-Door Electromagnetic Lock with Reversible Magnet Manual Reversible magnet for left or right-swing doors. Perfect for cabinets, small enclosures, or pedestrian gates. Selectable
More information8. Do not install this product on the exterior of buildings. 9. Do not use as a doorstop. This will void warranty.
INSTALLATION 8375 Surface MicroMag Electromagnetic Lock Pre-Installation Instructions 1. This product must be installed according to all applicable building and life safety codes. 2. Due to the variety
More informationInstructions For PG-1200RC Magnetic Locking Devices
Instructions For PG-1200RC Magnetic Locking Devices (Remote control distance up to 10 meters) Ver. 18.1 Please Read Carefully Before Installing Magnetic Lock A. Carefully for handling to prevent damage
More information2904 Power Supply Installation Instructions I-EA00041
FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and
More informationACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery
More informationSTANDARD / DOUBLE STANDARD MAGNETIC LOCK
STANDARD / DOUBLE STANDARD MAGNETIC LOCK INSTALLATION MANUAL INDOOR ELECTROMAGNETIC LOCK SERIES Spec/Model GEM-300 Single GEM-600 GEM-800 GEM-1200 Double GEM-D600 GEM-D800 GEM-D1200 Holding Force 300lbs
More informationInstalling the gate post bracket with the cardboard arm template
......... Installing the gate post bracket with the cardboard arm template... Installing gate posts brackets and arms for Push-to-Open or Pull-to-Open gates... Connection of Power Source 240Vac or Solar...
More informationInstalling the gate post bracket with the cardboard arm template
......... Installing the gate post bracket with the cardboard arm template... Installing gate posts brackets and arms for Push-to-Open or Pull-to-Open gates... Connection of Power Source 240Vac or Solar...
More informationME217PIB / ME503PIB SMART INTERLOCK TECHNOLOGY ACME ADAPTER INTERLOCK BRACKET INSTALLATION AND OPERATING INSTRUCTIONS
ME217PIB / ME503PIB SMART INTERLOCK TECHNOLOGY ACME ADAPTER INTERLOCK BRACKET INSTALLATION AND OPERATING INSTRUCTIONS ME825-16 / ME825-10 (Not Included) ME217PIB / ME503PIB ME229F5-1 / ME449F8-1 (Not Included)
More informationINSTALLATION INSTRUCTIONS SHEAR LOCKING MAGNET 1561TJ MAX. HOLDING FORCE 2000 lbs.
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS SHEAR LOCKING MAGNET 1561TJ MAX. HOLDING FORCE 2000 lbs. REFER TO THE
More informationLCN AUTOMATIC OPERATORS
LCN AUTOMATIC OPERATORS SENIOR 9530 SENIOR 9540 SENIOR 9550 SENIOR 9560 8310 ACCESSORIES LCN ELECTROMECHANICAL POWERED SYSTEMS ELECTROMECHANICAL AUTOMATIC OPERATORS LCN s electromechanical products are
More informationCARE-C Light Curtain Installation Instructions.
The Next Generation of Freight Elevator Doors www.couriondoors.com CARE-C Light Curtain Installation Instructions For Immediate Help Call 1-800-533-5760 q Install Mounting Brackets If your Gate Guides
More informationAlarm Controls Product Guide
Alarm Controls Product Guide Manufacturers of Quality Security Products Since 1971 19 BRANDYWINE DRIVE DEER PARK, NY 11729 WWW.ALARMCONTROLS.COM 800-645-5538 www.alarmcontrols.com 1 About ABOUT ALARM CONTROLS
More information2965 Magnetic Shear Lock Installation Instructions
MAGNETIC SHEAR LOCK 2965 INSTALLATION INSTRUCTIONS REFER TO THE PROPER TEMPLATE ACCORDING TO THE TYPE OF DOOR AND FRAME APPLICATION. READ THESE INSTRUCTIONS AND STUDY THE TEMPLATE THOROUGHLY BEFORE BEGINNING
More informationSECURITY DOOR CONTROLS
CR4 FOUR STATION CONTROL MODULE The CR4 module operates on 12V or 24V DC and provides control of four (4) stations. Each CR4 station accepts a Dry () trigger input and provides one (1) Fused 2 Amp SPDT
More informationMEP801PIK / MEP801PIKL / MEP801PIH / MEP801PIHL SMART INTERLOCK TECHNOLOGY HOSE END VALVE HOLSTER INSTALLATION AND OPERATING INSTRUCTIONS
MEP801PIK / MEP801PIKL / MEP801PIH / MEP801PIHL SMART INTERLOCK TECHNOLOGY HOSE END VALVE HOLSTER INSTALLATION AND OPERATING INSTRUCTIONS Application: Designed to provide a durable and convenient receptacle
More informationMOUNTING INSTRUCTIONS FOR TJ1000 SERIES INSWINGING DOORS ******READ THOROUGHLY BEFORE INSTALLING******
MOUNTING INSTRUCTIONS FOR TJ1000 SERIES INSWINGING DOORS ******READ THOROUGHLY BEFORE INSTALLING****** Handle Electro-Magnets carefully. Any damage to the mating surface may significantly reduce the holding
More informationCOOKSON OWNER'S MANUAL
COOKSON OWNER'S MANUAL FD-2A AUTOMATIC RESETTING FIRE DOOR HOIST OPERATOR R US RECOGNIZED COMPONENT CONFORMS TO UL 325 3040233 9045.DWG ECN 0986 REV 2 PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENTS:
More informationINSTALLATION MANUAL ACL 5500 COMBUSTION SAFETY CONTROLLER
5500 COMBUSTION SAFETY CONTROL INSTALLATION MANUAL FOR 5500 COMBUSTION SAFETY CONTROLLER WARNING This manual must be read in its entirety before installation of this controller. Installation must be performed
More information50 1/50 2 Directional Contactor Installation
50 1/50 2 Directional Contactor Installation Thank you for purchasing our 5091 or 5092 Directional Contactor. We take great pride in our products and feel certain that this Contactor will offer you many
More information* * M400 Series Double Locks. Double Electromagnetic Locks: M422, M452, M492. Installation Instructions. Mounting Bracket (2)
*44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Mounting Bracket (2) Inside Mounting Bracket Screws** (4) Mounting Bracket Screws**
More informationMODEL SCA Installation and Operation Manual Important:
MODEL SCA Installation and Operation Manual Important: This manual contains specific cautionary statements relative to worker safety. Read this manual thoroughly and follow as directed. It is impossible
More informationSECURITY DOOR CONTROLS 801 Avenida Acaso, Camarillo, Ca (805) Fax: (805)
SECURITY DOOR CONTROLS 801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com HI-SHEAR EMLOCKS 1565 & 1566 INSTALLATION INSTRUCTIONS
More informationGateCrafters Automatic Gate Lock Instruction Manual GCLOCK
GateCrafters Automatic Gate Lock Instruction Manual GCLOCK Introduction The GateCrafters Automatic Gate Lock is designed to provide extra security and stability to your gate opener system. There are numerous
More information1.0 Features and Description
1.0 Features and Description The is an intelligent actuator designed for precise control of quarter turn valves and dampers. Using stepper motor technology, the SmartStep proportionally positions valves
More informationGeneral Information. Notations and Conventions. Compatibility Check. Kit Description. Call-Outs. Part Lists Great Plains Manufacturing, Inc.
Part Lists Great Plains Manufacturing, Inc. 1 Installation Instructions Loup Shaft Monitor Used with Drill models: Compatible with most 1995 and later, two- and three-box drills with 5 8 -inch square main
More informationTop-of-Pole Mount for 6 Modules (TPM6) For Module Type D
Top-of-Pole Mount for 6 Modules (TPM6) For Module Type D ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 2, Rev D PCN 121712-29 Top-of-Pole Mount for 6 Modules (TPM6) For Module Type
More informationModels: DC Electric Vibrators. Operating Instructions CEG CEG CEG CEG CEG CEG
DC Electric Vibrators Operating Instructions Global External bin & hopper 12 & 24 Volt DC Electric Vibrators Models: CEG-400-12 CEG-800-12 CEG-1200-12 CEG-400-24 CEG-800-24 CEG-1200-24 Global Manufacturing
More informationInstallation, Operation, and Maintenance Manual. Automatic Fire Damper
Installation, Operation, and Maintenance Manual Automatic Fire Damper Part # 458295 Designed to close in fire situations. Reset by activating the reset switch. UL Listed Constructed in Accordance with
More informationSunwize Water Pumping Kit Quick Start
Document # 310014 Sunwize Water Pumping Kit Quick Start The purpose of this guide is to assist you in setting up your system quickly and efficiently. Important! Prior to field installation Determine and
More informationSunwize Power Ready Express Quick Start
Document # 310002 Sunwize Power Ready Express Quick Start The purpose of this guide is to assist you in setting up your system quickly and efficiently. Important! Prior to field installation Determine
More informationME868PIB SMART INTERLOCK TECHNOLOGY TURBO FLO LE PROXIMITY INTERLOCK BRACKET INSTALLATION AND OPERATING INSTRUCTIONS
ME868PIB SMART INTERLOCK TECHNOLOGY TURBO FLO LE PROXIMITY INTERLOCK BRACKET INSTALLATION AND OPERATING INSTRUCTIONS ME868-16 Turbo-Flo LE Adapter (Not Included) ME441F8 Cap (Not Included) ME868PIB Application:
More informationGE Sensing & Inspection Technologies
GE Sensing & Inspection Technologies Modus Model RPM-1 Room Pressure Monitor Installation and Setup Guide 1. GENERAL The RPM-1 monitors either positive or negative room pressures (see the Datasheet for
More informationUSERS GUIDE LO-21U LOCKOUT RELAY
USERS GUIDE LO-21U LOCKOUT RELAY PRODUCT DESCRIPTION The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with BEA s Bodyguard or DK-12 overhead
More informationINSTALLATION MANUAL FSS1 HIGH SECURITY DOOR MONITORING SENSOR
INSTALLATION MANUAL 1. INTRODUCTION The FSS1 is a patented device designed to provide a high security door position monitoring solution. It is the ideal higher security replacement for traditional balanced
More information280+ SHEARLOCK INSTALLATION AND WIRING MODELS: 280+ and 280+TRD TRD
INSTALLATION AND WIRING MODELS: 280+ and 280+TRD 280+ Standard model is a concealed electromagnetic shear lock designed to fit standard hollow metal doors and frames. In cases where the top of the door
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model M38 and M68 Magnalocks (Versions L, S and LS with D and T Options)
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model M38 and
More informationA1500, A1500NF SPEED SWITCH SINGLE SET POINT - SELF CONTAINED. Introduction
A186-05, Page 1 952-361-3026, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 A1500, A1500NF SPEED SWITCH SINGLE SET POINT - SELF CONTAINED Introduction The MAXIGARD A1500
More informationLOCKNETICS MagForce+ Series. Locknetics MagForce Traffic Control Magnet MEA
Locknetics MagForce+ Locknetics new MagForce Plus generation of electromagnetic locks is the evolution of the industry leading 390 Series.The MagForce Plus family consists of the 390+ with 1650 lbs of
More informationAccessories 286 SDC SECURITY DOOR CONTROLS
8 Security Door Controls From wireless remote controls to durable door holding & release devices, to REX sensors, timers, ball and magnetic switches, and from concealed contact to universal mounting enclosure
More information8. Do not install this product on the exterior of buildings. 9. Do not use as a doorstop. This will void warranty. Installation Instructions
INSTALLATI DE8310 Delayed Egress Electromagnetic Locks Pre-Installation Instructions 1. This product must be installed according to all applicable building and life safety codes. All installations must
More informationProcedure Replacing a Cover
Procedure 7.1 - Replacing a Cover Cover Removal 1. Remove two screws, one each side, from the front of the top cover. Remove the top cover. See Diagram 7.1. Diagram 7.1 - RBK 815 Covers Top Cover Left
More informationTop-of-Pole Mount for 6 Modules (TPM6) For Module Types A, B, & C
Top-of-Pole Mount for 6 Modules (TPM6) For Module Types A, B, & C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation YOUR DISTRIBUTOR SOLIGENT 800-967-6917 www.soligent.net Version 2, Rev D PCN
More informationLCN 9740 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9740 series operator is shipped with motor gearbox, control box, regular arm, header, and mounting hardware. Actuators available separately, see
More information30GX AIR-COOLED LIQUID CHILLER
30GX-5SB 30GX080-265 AIR-COOLED LIQUID CHILLER PERFORMANCE DATA FIELD WIRING DIAGRAM 1998 Carrier Corporation Syracuse, New York 13221 Form 30GX-5SB Supersedes 30GX-4SB Printed in U.S.A. 5-98 Catalog No.
More informationEMLock Magnetic Locks
EMLock EMLock Lifetime Warranty NSI/HM 156.23 Grade 1 CSFM 3774-0324:100 ME City of New York 768-80-S 1510 Series Grade 1 1650 lb / 748 Kg Holding Force ELECTRICL SPECIFICTIONS Single: 350m @ 24VDC; 670m
More informationThe Complete System Solution! Highest Grade Electronic Components RoHS Compliant.
Advantages of the 72 Alternating Relay The Complete System Solution! Highest Grade Electronic Components RoHS Compliant. The Model 72 series Alternating Relay is designed for duplex pumping systems where
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FORCE 10 SPORT R1 REAR DISC CONVERSION KIT A126-50 2005-10 Chevrolet Silverado and GMC Sierra Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationRETRO SOLUTIONS PRODUCT CATALOG
RETRO SOLUTIONS PRODUCT CATALOG 4634 S. Presa Street, San Antonio, TX 78223 Phone 210-533-1231 Fax 210-533-2211 www.southernfolger.com See who we are. See all we do. T A B L E O F C O N T E N T S RETRO
More informationD24-53 Series Electric Non-Spring Return Actuators 53 lb in Models (6 N m)
Installation Instructions D24-53 Issue Date November 4, 23 D24-53 Series Electric Non-Spring Return Actuators 53 lb in Models (6 N m) Installation IMPORTANT: The D24-53 Series actuator is intended to control
More informationEM101 LOW FLOW MAGNETIC FLOWMETER INSTRUCTIONS
Spec Tech Industrial 203 Vest Ave. Valley Park, MO 63088 Phone: 888 SPECTECH Email: sales@spectechind.com www.spectechind.com EM101 EM101 LOW FLOW MAGNETIC FLOWMETER INSTRUCTIONS LOW FLOW MAGNETIC FLOWMETER
More informationVehicle Rear Observation System With Integrated Parking Sensors
Vehicle Rear Observation System With Integrated Parking Sensors Model: CAMSBAR Installation/User Manual Features: 2.5" LCD Color Display 2 Ultra Sonic Rear Obstacle Sensors On-screen Display Function Automatically
More informationSIGNETMARINE. Livewell Bait Pump Alarm. No Dead Bait.
B A I T WAT C H SIGNETMARINE Livewell Bait Pump Alarm No Dead Bait. The SIGNETMARINE BaitWatch System alerts you to a livewell pump problem before your fishing trip turns into one. The loud alarm and dual-color
More informationE-S Allegiant Series Single Swing and Dual Swing Gate Opener
Estate Swing brand gate openers are a Sequoia Brands, Inc. product. Please visit www.estateswing.com for manual updates and other product information This gate opener is low voltage and bolt on specifically
More informationcel SECURITY DOOR CONTROLS Value Engineered Access Hardware sdcsecurity.com Power Supplies Exit Switches
Security Door Controls cel TM Value Engineered Access Hardware Excel E1200 Excel E600 Excel E300 Excel Series Value Engineered Access Hardware from SDC Economically Priced Alternative to Low Cost Imports
More informationOFFICE PARTITIONS. Data Port Openings. Use cable tie bracket to dress data cables under panels. STEP 1
N Power Box Opening Data Port Openings Rear View Front View Remove opening blanks on raceway cover for power and data. If panel contains no electric or data and is used as a pass-thru, leave opening blanks
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationMODEL MSD MOTION CONTROL INSTALLATION AND OPERATION
CONVEYOR COMPONENTS COMPANY 130 Seltzer Road, PO Box 167 Croswell, MI 48422 USA PHONE: (810) 679-4211 TOLL FREE (800) 233-3233 FAX: (810) 679-4510 Email: info@conveyorcomponents.com http://www.conveyorcomponents.com
More information12V Central Lock Universal Remote For Keyless Entry p/n
12V Central Lock Universal Remote For Keyless Entry p/n 900.550 Kit include: Functions: Qty Description 1 Electronic Control Box 3 Remote Control 1 Siren 1 Main Loom 12 wires 1 LED Loom 2 wires 1 Input
More information9540 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9540 SERIES The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated,
More informationExcel Series Value Engineered Access Hardware
Excel Series Value Engineered Access Hardware Excel E1200 Economically Priced Alternative to Low Cost Imports Quality and Flexibility for Commercial Applications. The Excel product line is designed for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationVertical Housing EMLock Discount Code GK LIST. Retrofit Kit for Discontinued Locknetics 390+ PLUS
EMLock Vertical Housing EMLock LIST Vertical Housings - Side jamb mount, aprovides 2,400 or 3,300 lbs. of holding force. 1572VV82 Vertical Housing for 1572 EMLock, 8 length, for 84" opening - INCLUDES
More informationEMLock Magnetic Locks
EMLock EMLock Lifetime Warranty NSI/HM 156.23 Grade 1 CSFM 3774-0324:100 ME City of New York 768-80-S GWXT uxiliary Locks CVXJ urglary Resistant Electrically Operated Door Lock UL10C Positive Pressure
More information