DOLPHIN INFRARED TAP DB800 / DB825 TECHNICAL HELPLINE DOLPHINSOLUTIONS.CO.UK DIAMETER PROJECTION TO SPOUT

Transcription

1

2 Ø38 Min 23 Max º 95 Min 2 Max 40 Power Source DB800 / DB825 DOLPHIN INFRARED TAP WRAS approved product Touch Free Tap for ultimate hygiene prevents cross contamination Quality polished or brushed chrome plated brass finishes available from stock other finishes available to special order Water Supply: Single inlet cold or pre-mixed a TMV2 or TMV3 thermostatic mixing valve is recommended for premixed applications Flow rate 5 litres/minute (1.89 litres/ minute also available please specify) Power Source: Plug-in 9 Volt transformers or 9 Volt Battery (with low battery warning) for other power source options see page Auto adjusting sensor range mm Sensor range and tap settings including optional hygiene flush and security time can be adjusted manually or by using remote control (DB51) Mandatory Hygiene Flush feature can be specified to combat Legionella 2 year manufacturer s warranty Interchangeable TJ M18 Neoperl Cache Aerator We recommend our Dolphin Blue DB61 TMV3 be used in conjunction with this Dolphin Blue tap Exceeds the BREEAM requirements for taps for a maximum flow rate of less than 6 litres per minute (LPM) at a water pressure for 0.3 mega pascals (MPA) HEIGHT DIAMETER PROJECTION TO SPOUT 15 MM 38 MM 95 MM Power Source: Plug-in 9 Volt transformers or 9 Volt Battery Power connections: tap: female / power source: male Maximum water temperature 70ºC Operating pressure bar (7 116PSI) Counter Hole: diameter 2-40mm Minimum/maximum thickness: 23-40mm PRODUCT CODES BATTERY POWERED Polished Chrome Plate DB800C Brushed (Satin) Chrome Plate DB800S-2 TRANSFORMER POWERED Polished Chrome Plate DB825C Brushed (Satin) Chrome Plate DB825S-2 TECHNICAL HELPLINE DOLPHINSOLUTIONS.CO.UK

3 Ø38 Min 23 Max º 95 Min 2 Max 40 Power Source DB800 / DB825 DOLPHIN INFRARED TAP Touch Free Tap for ultimate hygiene prevents cross contamination Quality polished or brushed chrome plated brass finishes available from stock other finishes available to special order HEIGHT DIAMETER PROJECTION TO SPOUT 15 MM 38 MM 95 MM Water Supply: Single inlet cold or pre-mixed a TMV2 or TMV3 thermostatic mixing valve is recommended for premixed applications Flow rate 5 litres/minute (1.89 litres/ minute also available please specify) Power Source: Plug-in 9 Volt transformers or 9 Volt Battery (with low battery warning) for other power source options see page Power Source: Plug-in 9 Volt transformers or 9 Volt Battery Power connections: tap: female / power source: male Maximum water temperature 70ºC Operating pressure bar (7 116PSI) Counter Hole: diameter 2-40mm Minimum/maximum thickness: 23-40mm Auto adjusting sensor range mm Sensor range and tap settings including optional hygiene flush and security time can be adjusted manually or by using remote control (DB51) Mandatory Hygiene Flush feature can be specified to combat Legionella 2 year manufacturer s warranty Interchangeable TJ M18 Neoperl Cache Aerator We recommend our Dolphin Blue DB61 TMV3 be used in conjunction with this Dolphin Blue tap Exceeds the BREEAM requirements for taps for a maximum flow rate of less than 6 litres per minute (LPM) at a water pressure for 0.3 mega pascals (MPA) PRODUCT CODES BATTERY POWERED Polished chrome plated DB800C Brushed chrome plated DB800S-2 TRANSFORMER POWERED Polished chrome plated DB825C Brushed chrome plated DB825S-2 TECHNICAL HELPLINE DOLPHINSOLUTIONS.CO.UK

4 DB800/DB825 Tap Range - Parts Diagram 11 Item Description Part No. Item Description Part No. - Seals and Screws Kit DB Solenoid Valve Kit DB Screw 6 Solenoid valve 4 O-ring 5 Diaphragm 3 O-ring 5 Diaphragm DB Nano sensor DB Battery Box (IP67 version) DB83M - Solenoid BS-Housing Kit DB Battery Box DB82M 7 S 8 Filter 11 9V Transformer (100mA) DB70M 9 Nipple 11 9V Transformer (300mA) DB85M T: F: E: info@dolphindispensers.co.uk

5 INSTALLATION AND MAINTENANCE GUIDE DB 800 and DB 825 Dolphin Blue Counter Mounted Electronic Infra-Red Tap Important: Read carefully before installing product September 2010

6 CONTENTS Important: Please read page 6-7 before commencing installation 3 Technical Data 4 Pack Contents DB 800C DB 825C 5 Pre Installation information 6-7 Tap Installation 8-10 Settings Adjustment 11 Battery Replacement Instructions How to replace the battery at BC 800C 12 Maintenance Filter cleaning instructions Care and cleaning of chrome and special finishes 13 Trouble-Shooting 14 Spare Parts List 15 Limited Warranty 2 Dolphin Blue 800 Series

7 TECHNICAL DATA DB 800C Electronic tap for cold or premixed water to be powered by battery. DB 825C Electronic tap for cold or premixed water to be powered by electricity. Power Supply: Operating Water Pressure: Sensor Range: Minimum Sensor Range: Maximum Sensor Range: Security time: 9V battery or 9V transformer Optional: IP 67 battery box for 6 x 1.5 V AA batteries bar ( PSI) With water pressure of more than 8 Bars, use a pressure reducing valve for reduction. Self adjusting sensor. Adjustable with remote control 50 mm. 160 mm. 90 seconds. Adjustable with remote control. 24 hours hygiene flush: optional, to be enabled with DB 51 remote control. Hot Water Supply: Max 70 C. 800 Series Dolphin Blue 3

8 PACK CONTENTS Familiarize yourself with the parts names and confirm that the parts are included. DB 800C 1. 1x Tap and attachments 2. 1x Solenoid valve, housing, filter and adapter 3. 1x Transformer 4. 1x Allen key DB 825C 1. 1x Tap and attachments 2. 1x Solenoid valve, housing, filter and adapter 3. 1x Battery box 4. 1x Allen key 4 Dolphin Blue 800 Series

9 PRE INSTALLATION INFO Check contents Separate all parts from the packaging and check each part with the Pack contents section. Pay attention to the different models variations. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to install your electronic tap until you obtain the missing parts. Warnings: Do not install the system facing a mirror or any other electronic system operated by an infra-red sensor. To prevent reflection problems, it is recommended to keep a minimum distance of 1.50 meters between the tap and any other objects. Shut off water supply O Ring Gasket Disk Hexagonal Nut Preparation for Installation Flush water supply lines thoroughly before installing the tap. Do not allow dirt, Teflon tape or metal particles to enter the tap. Shut off water supply. Important: All plumbing is to be installed in accordance with applicable codes and regulations. Bell-Chem recommend that DB 800C and DB 825C Dolphin Infra-red taps are connected to a water supply which is temperature regulated by a TMVE Thermostatic valve or TMV3 Thermostatic valve for medical applications. (Please call the Dolphin Blue Technical Helpline should you have any queries +44 (0) ). 800 Series Dolphin Blue 5

10 TAP INSTALLATION Step 1 Remove all mounting hardware Shut off the water supply and remove the hexagonal nut, the disk and the gasket. Do not remove the O-ring from the base of the tap. Step 2 Installing the tap 1. Place the tap with O-ring into the hole in deck or lavatory. Make sure the O-ring is located between the deck or lavatory and the bottom of the tap. 2. Slide gasket over the flexible hose. 3. Secure the tap to deck or lavatory with the hexagonal nut and the disk. Step 3 Connecting the water supply 1. Fit the pipe to the housing of the solenoid valve. Important: inlet and outlet should follow the indicating arrow at the solenoid housing. 2. Fit the water supply inlet to the adapter at the solenoid valve housing. Note: Make sure that the filter is assembled between the housing of the solenoid valve and the adapter. Important: this tap was supplied with the new Self Adjusting Sensor. The ideal sensor range for the specific location will be set automatically. Hexagonal Nut O Ring Gasket Disk Water Outlet Filter Water inlet Before proceeding to step 3 check that no objects are in front of the sensor besides the washbasin. Now remove the protecting sticker that covers the sensor. 6 Dolphin Blue 800 Series

11 TAP INSTALLATION Step 4 Connecting the power source 1. For DB 800C: Install the Battery version Transformer version battery box at the wall under the sink using the two sided adhesive foam tape. Important: The cable connection must point down. (You can use an extension cable in order to Transformer assemble the battery box up to 10 meters away from the sink). 2. For DB 825C: Plug the Transformer in to the electricity socket and connect the connectors. 3. After you have connected the power source (Battery or Transformer) wait 10 seconds in order to allow the system to set the ideal sensor range. Then the product will be ready for use. 4. Turn on the central water supply and the shut-off valves. 5. Check for leaks. Note: this tap includes a special aerator that allows you to adjust the water stream direction on site in order to prevent water splashing if needed. To change the angle of the water stream, simply move the adjustable tilting plate by pressing it smoothly. 6. If the automatically adjusted sensor settings is not satisfactory, please refer to the section entitled Settings adjustment. 7. We recommend that the temperature of the water at outlets is regulated to 40-41ºC or in accordance with current regulations. 800 Series Dolphin Blue 7

12 SETTINGS ADJUSTMENT Adjusting the sensor range with the remote control This tap was supplied with the new Self Adjusting Sensor. The ideal sensor range for the specific location will be set automatically. Only if necessary, use the DB 51 remote control to adjust the sensor range as follows: Shut off the water supply. In order to adjust the sensor with the remote control hold the remote control straight in front of the sensor in a distance of about 4 (10cm). Choose the function you want to adjust by pressing once on one of the function buttons. After pressing once on a specific function button, a quick flashing of the red light at the front of the sensor will occur. At this stage, you can change the setting by pressing the (+) or the (-) buttons, every push will increase or decrease one level. After finishing the adjustment, turn the water supply back on Detection Range: Press + to increase detection range and to decrease the detection range of the sensor. Entrance to manual range adjustment: This mode allows you to adjust the sensor range using your hand to indicate the desired distance. Press the AD J button. Wait until a quick flashing of the red light of the sensor eye is perceived. Place your hand at the desired distance. The range will be adjusted when the light will stop blinking. For other settings using the DB 51 Remote Control, please see the DB 51 Remote Control Instructions booklet. 8 Dolphin Blue 800 Series

13 SETTINGS ADJUSTMENT Adjusting other settings with the remote control Security time: The Security time, prevents continuous flushing of water due to reflections or vandalism. By default, if the sensor is covered for more than 90 seconds the water flow will shut automatically. To resume regular operation any obstruction must be removed. Press the SEC button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then, press + to increase the security time and to reduce it. Delay in time: The delay in time prevents unwanted activations. It is recommended to change the delay in time for flush valves for urinals or toilets only. If required, the delay in time can be modified also in taps as follows: Press the IN button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then, press + to increase the delay in time and to reduce it. Delay OUT time: This button allows modifying the water flow time after the user removes his hands from the tap. A delay out time close to 0 will save more water. An increased delay out time will make the user experience more comfortable. If required, the delay out time can be modified as follows: Press the OUT button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then, press + to increase the delay out time and to reduce it. 24 hour hygiene flush: This function is ideal to maximize hygiene and prevent Legionella and other diseases. It also helps to prevent pipes from freezing, keeping the water moving through the pipes every 24 hours. The optional 24 hours hygiene flush is disabled by default. To activate the hygiene flush, press the clock button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then press + to activate the hygiene flush or to deactivate it. 800 Series Dolphin Blue 9

14 SETTINGS ADJUSTMENT Lock out time: It is possible to program a lock out time in these products upon request. This lock out time allows a user to activate the tap, only after a specific amount of time has passed. If a specific lock out time was preset in a The product as default, and you would like to deactivate it, press the lock button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then press + to activate the lock out time or to deactivate it. To activate it again, press the lock button and without releasing it, press the + button once. Temporary Off function: This function is ideal to perform any kind of activity in front of the sensor without operating the system (for example, cleaning). Taps will remain shut for 1 minute when this button is pressed once. To cancel this function and to return to normal operation press the On/Off button again or wait 1 or 2 minutes depending on the product. Reset buton: This function allows the sensor to return to the original factory preset settings. If required, press the Reset button and without releasing it, press the + button once. Note: After the reset function is performed, the Self Adjusting Sensor will set again the ideal sensor range for the specific location. Check that there are no objects in front of the sensor and wait 10 seconds in order for the product to be ready for use. 10 Dolphin Blue 800 Series

15 BATTERY REPLACEMENT Battery models only When the battery weakens, the red indicator light will blink at a constant rate. The battery must be replaced within two weeks. To replace the battery at battery models: 1. Carefully open the battery s box. 2. Remove the old battery. 3. Replace the used battery with a new 9V battery (Lithium battery is recommended). 4. Close the box. Important: This tap was supplied with the new Self Adjusting Sensor. The ideal sensor range for the specific location will be set automatically again after changing the battery. Check that there are no objects in front of the sensor after the battery replacement was completed. After you have connected the power source wait 10 seconds in order to allow the system to set the ideal sensor range. Then the product will be ready for use. 800 Series Dolphin Blue 11

16 MAINTENANCE Filter cleaning instructions This tap is provided with a stainless steel filter preventing foreign particles to enter the lines. If the water flow has decreased, this may be because the filter is clogged. The filter can be cleaned as follows: 1. Shut-off the water shut off valve. 2. Disconnect the water supply pipe from the adaptor and disassemble the filter from it. a. Wash the filter under running water. b. Reassemble the parts. c. Restore the incoming water supply. d. Make sure that there is no water leakage. Care and cleaning of chrome and special finishes DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. Use of any prohibited cleaning or maintenance products or substances could damage the surface of the tap. For surface cleaning of taps use ONLY soap and water, then wipe dry with clean cloth or towel. When cleaning bathroom tile, the taps should be protected from any splattering of harsh cleansers. 12 Dolphin Blue 800 Series

17 TROUBLE SHOOTING PROBLEM INDICATOR CAUSE SOLUTION Sensor flashes continuously when user s hands are within the sensor s range Low batteries Replace batteries Range is too short Increase the range with remote No water comes out of the tap Red light in the sensor does not flash once when user s hands are within the sensor s range Range is too long ie tap has gone into security mode Batteries are completely used up Sensor is picking up reflections ie tap has gone into security mode Decrease the range with remote Replace batteries Decrease the range or eliminate cause of reflection Red light in the sensor flashes once when user s hands are within the sensor s range Connectors between the electronic unit and the solonoid are disconnected Debris or scale in solonoid The central orifice in the diaphragm is plugged or the diaphragm is torn Connect the electronic unit connectors to the solonoid Unscrew solonoid, pull out the plunger and the spring from the solonoide and clean them. Use scale remover material if needed. When replacing the plunger,please make sure that the spring is in vertical position Unscrew solonoid and clean the orifice and/or replace diaphragm The water supply pressure is higher than 8 bars Reduce the water supply pressure Water flow from spout does not stop Sensor flashes once when user s hands are within the sensor s range Red light in the sensor does not flash when user s hands are within the sensor s range Debris or scale in diaphragm Sensor is dirty or covered Sensor is picking up reflections from the washbasin or another object Unscrew solonoid, remove diaphragm and clean or replace. Use scale remover if needed. Clean or eliminate cause of interference Decrease the range or eliminate case of reflection Water flow diminished Filter or aerator is clogged Remove, clean and reinstall 800 Series Dolphin Blue 13

18 SPARE PARTS LIST Self adjusting sensor kit Cat.No. DB Solenoid valve kit Cat. No. DB Solenoid housing kit Cat. No. DB Battery box (Battery models only) Cat. No. DB Transformer (Transformer models only) Cat. No. DB Optional accessories: Extension cable (Battery models only) Cat. No. DB Remote control Cat. No. DB IP 67 Battery box with 6 x 1.5V AA batteries Cat.No. DB IP 67 Transformer box with 300 ma transformer Cat.No. DB Battery Back up device Cat.No. DB Power splitter (2 ways) Cat.No. DB Power splitter (3 ways) Cat.No. DB Power splitter (4 ways) Cat.No. DB Dolphin Blue 800 Series

19 LIMITED WARRANTY This product is covered by a limited warranty of two years from date of purchase. During this period, Bell-Chem Products undertakes, at its option, to repair or replace any faults caused by defective materials or manufacturer defaults that may arise (see Limited Warranty). The guarantee does not cover faults, labour costs or damage caused by incorrect installation and/or maintenance, wear and tear, battery, or water composition. This includes, but is not limited to the following: Incorrect installation, inversions of supply pipes. Pressures or temperatures exceeding recommended limits. Improper manipulation, tampering, bad or lapsed maintenance. Foreign bodies, dirt or scale introduced by the water supply. 800 Series Dolphin Blue 15

20 Request your 400 page catalogue today on Bell-Chem Products Company Haywood Way, Hastings TN35 4PL Tel: +44 (0) Fax: +44 (0) Part of the Dolphin Range

21 Dolphin Blue Infrared Systems Important Design Tips DOLPHIN

22 Dolphin Blue Infrared Systems Designing a washroom including Dolphin Blue Infrared Systems Dolphin Blue Infrared Taps, Shower Controls and Urinal Flush Valves offer significant water and energy savings. However, there are some simple DO s and DON Ts and TIPs which will help avoid 99% of the situations often associated with infrared systems for washrooms. It should be noted that these details are not exhaustive but will help eliminate 99% of situations. It is recommended that for larger projects especially where design restraints will result in taps being set on minimum or maximum settings, we would advise a very simple mock-up be set with materials to be used to ensure infrared device operates as desired. DO s Battery Back up DO include a battery back-up device when installing a transformer powered infrared tap in an accessible washroom. Security Time DO ensure security time is set at approximately 20 seconds on infrared taps especially in locations susceptible to vandalism. Also important: to be set at 20 seconds to comply with ECA/WTL scheme. Flow Rate DO specify what flow rate is required when placing your order. Taps - 6 litre / minute is standard. 4 litre / minute is readily available. Shower head - 9 litres/ minute is standard, 8 litres / minute is available. Please speak to the Dolphin Technical Helpline for other flow rates if required. Pressure DO ensure the static and dynamic pressure at the Dolphin Blue device is within the tolerances stated on the product literature / data sheet (please ask if you cannot find it). Most devices are tested to operate between 0.5 and 8 bar. If pressures are outside the stated tolerances please contact the Technical Helpline on Filters Do ensure filters supplied with the Dolphin Blue device are installed. It may not be sufficient to rely on the filters often included with thermostatic mixing valves as the gauge of the filter mesh may not be fine enough. It is also important to ensure pipes are flushed prior to connection and filters are inspected on a regular basis. Time between inspections will depend on hardness and quality of water. Distance from Transformer It is recommended you ensure the maximum distance between a Dolphin Blue Infrared Tap and its power source is 5 metres.

23 DON Ts Mirrors It is not advisable to locate a Dolphin Blue Infrared device directly opposite a mirror where the infrared eye faces the mirror in such a way that it could reflect itself as this can cause false activations even if the mirror is 2-4 metres away from the infrared eye. Panel Mounted Infrared Taps It is very important to ensure the distance between the sensor and the bottom of basin when installing a panel mounted Dolphin Blue Tap with an integral sensor is a minimum of 300mm above the bottom of the basin. Two Infrared Taps It is not advisable to locate infrared taps directly opposite each other where the infrared eyes face each other as this can also cause false activations even when there is a fair distance between them. TIPs High Visibility Clothing Avoid polished/ chrome strainers It is a feature of most infrared devices in the washroom market that the reflective strips on high visibility clothing may cause the device to operate, even if someone just walks past, with no intention of using it. The DB51 Dolphin Blue Remote Control can be used to reduce the range of a device to reduce these false activations but may not eliminate the phenomena completely. Minimum 300mm distance critical Polished Traps and Sink Surfaces When installing a Dolphin Blue Panel Mounted Tap with an integral sensor it is recommended that you avoid a highly polished chrome trap or sink surface it will act like a mirror to the tap sensor, potentially causing false activations and wasted water Tall Version Taps and Spout Lengths Consider the position of the water outlet / aerator in relation to the basin. Please feel free to discuss spout lengths with the Dolphin Technical Helpline on

24 washrooms worth experiencing Bell-Chem Products Company Haywood Way, Hastings, TN35 4PL DOLPHIN

25 Dolphin Blue Infrared Taps The majority of Dolphin Infrared Taps are now equipped by default with Neoperl Cascade PCA aerator which incorporates a 3.8 litre per minute flow regulator. Flow rate graph for Dolphin Blue Taps 8 7 Flow rate (Litres / Minute) Line Pressure (Bar) Pressure Range for Dolphin Blue Taps bar (7-116 PSI). For areas where the pressure is greater than 8 bar, use a pressure reducing valve. Other flow rate regulators are available on request. Please call the Dolphin Blue Technical Helpline on for assistance. Flow rate graph for Dolphin Blue Taps 8 7 Flow rate (Litres / Minute) Line Pressure (Bar) A 6 L/M aerator and flow regulator is still fitted to some models of the Dolphin Blue infrared tap range. DOLPHIN Bell-Chem Products Co Haywood Way Hastings East Sussex TN35 4PL Tel: Fax: info@dolphindispensers.co.uk

26

27 This certifies that DOLPHIN SOLUTIONS LTD has had the undermentioned product examined, tested and found, when correctly installed, to comply with the requirements of the United Kingdom Water Supply (Water Fittings) Regulations and Scottish Water Byelaws. DOLPHIN BLUE DB800 & DB825 COMBINATION TAP ASSEMBLIES The certificate by itself is not evidence of a valid WRAS Approval. Confirmation of the current status of an approval must be obtained from the WRAS Directory ( The product so mentioned will be valid until the end of: May Certificate No. Secretary Chairman, Product Assessment Group October 2014

28

29 DOLPHIN POWER SUPPLIES AND CONNECTORS TAPS, URINALS, WC AND SHOWERS (POWER CONSUMPTION 100mA PER DEVICE) DDEFAULT (SUPPLIED AS STANDARD) SWITCHING TRANSFORMERS 3 PIN PICTURE CONNECTOR DESCRIPTION INPUT VOLTAGE OUTPUT VOLTAGE FREQUENCY OUTPUT CURRENT CODE NUMBER UK transformer with 5 metre and cable male waterproof connector v 9v 50/60 Hz 300 ma DB85M MALE UK transformer with 5 metre and cable female waterproof connector v 9v 50/60 Hz 300 ma DB85F FEMALE DIP68 SWITCHING ENCAPSULATED TRANSFORMERS FOR HARDWIRE PICTURE CONNECTOR DESCRIPTION INPUT VOLTAGE OUTPUT VOLTAGE FREQUENCY OUTPUT CURRENT CODE NUMBER MALE IP68 switching transformer with 5 metre cable and water proof male connector unterminated (no plug) v 9v 50/60 Hz 300 ma DB69M FEMALE IP68 switching transformer with 5 metre cable and water proof female connector unterminated (no plug) v 9v 50/60 Hz 300 ma DB69F SOAP DISPENSERS (POWER CONSUMPTION 500mA PER DEVICE) DDEFAULT (SUPPLIED AS STANDARD) SWITCHING TRANSFORMERS 3 PIN PICTURE CONNECTOR DESCRIPTION INPUT VOLTAGE OUTPUT VOLTAGE FREQUENCY OUTPUT CURRENT CODE NUMBER UK 12V switching adaptor with 5 meter cable and male waterproof connector v 12v 50/60 Hz 500mA BC MALE DIP68 SWITCHING ENCAPSULATED TRANSFORMERS FOR HARDWIRE PICTURE CONNECTOR DESCRIPTION INPUT VOLTAGE OUTPUT VOLTAGE FREQUENCY OUTPUT CURRENT CODE NUMBER MALE IP68 Encapsulated switching transformer with 5 meter cable and male waterproof connector unterminated (no plug) v 12v 50/60 Hz 1.0A DB MULTIPLE PRODUCTS DIP68 SWITCHING ENCAPSULATED TRANSFORMERS FOR HARDWIRE PICTURE CONNECTOR DESCRIPTION INPUT VOLTAGE OUTPUT VOLTAGE FREQUENCY OUTPUT CURRENT CODE NUMBER IP68 Encapsulated switching transformer with 5 meter cable and male waterproof connector PICTURE MALE CONNECTOR unterminated (no plug) DESCRIPTION MALE IP68 Encapsulated switching transformer with 5 meter cable and male waterproof connector unterminated (no plug) v INPUT VOLTAGE v 12v OUTPUT VOLTAGE 12v 50/60 Hz FREQUENCY 50/60 Hz 1.0A OUTPUT CURRENT 2.5A DB CODE NUMBER BC68M Technical Helpline:

30 D10 WAY JUNCTION BOX TRANSFORMER FOR HARDWIRE DRAWING DESCRIPTION INPUT VOLTAGE OUTPUT VOLTAGE FREQUENCY OUTPUT CURRENT CODE NUMBER Junction box with transformer 12v Connection point of up to 10 products. Includes a 12VDC 4.2 Amp power supply transformer Requires cables as below : male /female 3m/10m v 12v 60 Hz 4.2A DB87 MALE Cable Male 3 metre Output for junction box including 3m cable male connector N/A N/A N/A N/A DB FEMALE Cable Female 3 metre Output for junction box including 3m cable female connector N/A N/A N/A N/A DB MALE FEMALE Cable Male 10 metre Output for junction box including 10m cable male connector Cable Female 10 metre Output for junction box including 10m cable female connector N/A N/A N/A N/A N/A N/A N/A N/A DB DB BATTERY BOXES DFOR TAPS, URINALS AND SHOWERS PICTURE CONNECTOR DESCRIPTION CONNECTOR CODE NUMBER MALE IP67 Black battery box Male waterproof connector DB83M PICTURE FEMALE CONNECTOR IP67 Black battery box Female waterproof connector DB83F MALE IP67 Black battery box Male waterproof connector DB82M FEMALE IP67 Black battery box Female waterproof connector DB82F DFOR SOAP DISPENSERS PICTURE CONNECTOR DESCRIPTION CONNECTOR CODE NUMBER Battery box for soap dispensers 6 x DD batteries Male waterproof connector DB PICTURE MALE CONNECTOR Technical Helpline:

31 POWER SPLITTERS D100 RANGE CONNECTOR DESCRIPTION CODE NUMBER Power splitter 2 ways F-M2 Cable length to product 100mm Cable length to power supply 100mm DB76-F-M2 Power splitter 2 ways M-F2 Cable length to product 100mm Cable length to power supply 100mm DB76-M-F2 Power splitter 3 ways F-M3 Cable length to product 100mm Cable length to power supply 100mm DB77-F-M3 Power splitter 3 ways M-F3 Cable length to product 100mm Cable length to power supply 100mm DB77-M-F3 D100 RANGE CONNECTOR DESCRIPTION CODE NUMBER Power splitter 2 ways F-M2 Cable length to product 1500mm Cable length to power supply 100mm DB76/15-F-M2 Power splitter 2 ways M-F2 Cable length to product 1500mm Cable length to power supply 100mm DB76/15-M-F2 Power splitter 3 ways F-M3 Cable length to product 1500mm Cable length to power supply 100mm DB77/15-F-M3 Power splitter 3 ways M-F3 Cable length to product 1500mm Cable length to power supply 100mm DB77/15-M-F3 DOLPHIN SOLUTIONS LTD Southpoint, Compass Park, Bodiam, Robertsbridge TN32 5BS. Technical Helpline: info@dolphinsolutions.co.uk

32 SOUTHPOINT, COMPASS PARK, BODIAM, ROBERTSBRIDGE, TN32 5BST, UNITED KINGDOM + 44 (0) TEL + 44 (0) FAX hello@dolpinsolutions.co.uk dolphinsolutions.co.uk