PARTS BOOK FLAIL HEADS 75 CUT 3PT HITCH SWING ARM

Transcription

1 PARTS BOOK FLAIL HEADS 75 CUT 3PT HITCH SWING ARM DIAMOND MOWERS, LLC 350 E 60 th St. North Sioux Falls, SD 5704 FOR WARRANTY CALL DIAMOND MOWERS DIRECT: OUR TECHNICIANS WILL DIAGNOSE YOUR SITUATION OVER THE PHONE TO GET YOU UP AND RUNNING QUICKLY. Phone: Fax: DIAMOND MOWERS, LLC

2 Page 2 Foreword This manual contains the parts breakdown and identification of the various components and structures that make up your mower implement. The illustrations, drawings, and diagrams in this manual are based on the latest information available at the time of publication. Your machine may have product improvements and features not yet contained in this parts manual. Diamond Mowers, LLC reserves the right to make changes at any time without notice or obligation. Diamond Mowers, LLC and Wetblade are trademarks of Diamond Mowers, LLC. This manual should be consulted prior and while assembling the unit, and anytime parts or assembly clarification is needed. Copyright 206 Diamond Mowers, LLC All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher assumes no responsibility for errors or omissions. No part of this book covered by the copyrights heron may be reproduced or copied in any form or by any means graphic, electronic, or mechanical, including photocopying, taping, or information storage and retrieval systems without written permission of the publisher.

3 Page 3 Table of Contents FLAIL HEADS 4 SWING FLAIL HEAD - 75 CUTTER ASSEMBLY 5 SWING FLAIL HEAD - 75 DRIVE ASSEMBLY 6 SWING FLAIL HEAD - DECAL IDENTIFICATION 7 FRAME ASSEMBLIES 8 SWING ARM ASSEMBLY - 3-POINT HITCH 9 SWING ARM ASSEMBLY - ROTATOR DECK ASSEMBLIES GEAR BOX ASSEMBLY DRIVE LINE ASSEMBLY 4 LIFT ASSEMBLIES X2 WELDED CYLINDER, SLUGGED X0 WELDED CYLINDER, W/2 SLUG 7 MISCELLANEOUS ASSEMBLIES 8 BEARING - GROUND ROLLER,

4 FLAIL HEADS

5 FLAIL HEADS Page 5 SWING FLAIL HEAD - 75 CUTTER ASSEMBLY CUTTERSHAFT BEARING GROUND ROLLER BEARING ASSY /8 LOCK WASHER /8 FLAT WASHER /2 LOCK WASHER /2 FLAT WASHER GR /2 H.S. LOCK WASHER KNIFE MOUNTING BOLT /2 X 2 NC PLOW BOLT /8 X NC HEX CAPSCREW /8 X -/4 NC HEX CAPSCREW /2 X -/2 NC HEX CAPSCREW /2 X -3/4 NC HEX CAPSCREW /2 X NC HEX CAP /2 X 2 H.S. NF HEX CAPSCREW /8 X H.S. NC SKT HEAD /8 NC HEX NUT /4-6 ACME HEX NUT /2 NC HEX NUT /6 NYLOCK JAM NUT CLEVIS SHOULDER BOLT " FLAP GREASE ZERK HOSE /8" GREASE ZERK BONNET - RIGHT SWING BONNET - LEFT SWING GROUND ROLLER BLOCK LOCK PLATE ADJUSTMENT ROD RIGHT ADJUSTMENT ROD LEFT " TRASH GUARD " FLAP BAR CUTTERSHAFT GUARD GROUND ROLLER BRACKET OUTER SKID SHOE - RIGHT SWING OUTER SKID SHOE - LEFT SWING DRIVE SIDE SKID SHOE - RIGHT SWING DRIVE SIDE SKID SHOE - LEFT SWING BEARING GUARD " GROUND ROLLER /8" BRASS COUPLER ****CUTTER SHAFTS COMPLETE**** 75" CUTTER SHAFT, SMOOTH CUT KNIVES Opt " CUTTER SHAFT, 3/6" HD KNIVES ****FLAIL KNIVES**** SMOOTH CUT FLAIL KNIFE /6" HD FLAIL KNIFE BLADE KITS Includes -0506, -46, & (smooth) Includes -0506, -46, & (HD)

6 FLAIL HEADS Page 6 SWING FLAIL HEAD - 75 DRIVE ASSEMBLY SHEAVE SHEAVE /6" TAPERLOCK BUSHING SHEAVE 6.3 IDLER ASSEMBLY /8 LOCK WASHER GR /8 FLAT WASHER GR /2 LOCK WASHER GR /8 SAE FLAT WASHER GR /6 LOCK WASHER MM LOCK WASHER H.S /4 FLAT WASHER GR MM LOCK WASHER GR MM LOCK WASHER /4 SAE FLAT WASHER GR /2 SAE FLAT WASHER GR /2 X 2 NC HEX CAPSCREW /8 X NC HEX CAPSCREW MM X 20MM X.25 HEX CAPSCREW /4 X 3-/2 NC HEX CAPSCREW MM X 40MM X 2.0 HEX CAPSCREW MM X 40MM X.75 HEX CAPSCREW /2 X 2 NC CARRIAGE BOLT /8 X H.S. NC SKT HEAD /2 X -3/4 NC CARRIAGE BOLT /6 X 2 NC HEX CAPSCREW /4 NC NYLOCK NUT /2 NC HEX NUT /2 NC NYLOCK NUT DOUBLE 630 V-BELT GEAR BOX ROSTA TENSIONER INPUT CONNECTION SHIELD PTO DRIVE SHAFT SLIP CLUTCH ASSEMBLY CLUTCH DISC TENSION SPRING NYLON BUSHING UPPER GEAR BOX BRACKET IDLER SPACER TAPERLOCK BUSHING, 6 SPLINE INPUT PTO SHAFT GUARD GEARBOX MOUNT REAR BELT COVER FRONT BELT COVER

7 DEMAND BRILLIANCE. FLAIL HEADS SWING FLAIL HEAD - DECAL IDENTIFICATION Page 7

8 FRAME ASSEMBLIES

9 FRAME ASSEMBLIES Page 9 SWING ARM ASSEMBLY - 3-POINT HITCH

10 FRAME ASSEMBLIES Page 0 SWING ARM ASSEMBLY - 3-POINT HITCH GARLOCK BUSHING HORIZONTAL BEARING PAD LOAD BEARING MD NYLON PAD /4 SAE FLAT WASHER GR /6 X 3-/4 NC HEX CAPSCREW GR /4 X 3/4 FLAT SKT HEAD CAPSCREW /6 NC NYLOCK NUT /4 NC NYLOCK NUT /4 X 2 ROLL PIN /4 DOUBLE HOSE CLAMP X 0 WELDED CYLINDER W/ 2" SLUG /2 MALE QUICK COUPLER HOSE /4 X 85 (/2MORB-90DEG X /2MP) /4 GREASE ZERK, STRAIGHT /4 X 90 DEG. GREASE ZERK CLEVIS PIN UPPER 3-PT PIN LOWER 3-PT PIN SWING ARM PIN BREAKAWAY PIN LYNCH PIN (LARGE) STAND PIN LYNCH PIN (SMALL) BUSHING GA BUSHING (LARGE) GA BUSHING (SMALL) GA BUSHING SPRING REST MOUNT PIVOT SWING ARM STATIONARY BREAKAWAY ARM PIVOT ARM ADJUSTMENT BRACKET

11 SWING ARM ASSEMBLY - ROTATOR FRAME ASSEMBLIES Page PIVOT THRUST BEARING GREASELESS BUSHING BEARING /8 LOCK WASHER GR /8 X -/2 NC HEX CAPSCREW /4 X 2 ROLL PIN X 2 WELDED CYLINDER W/ 2" SLUG /2 MALE QUICK COUPLER HOSE /4 X 48 (/2MORB-90DEG X /2MP) /4 GREASE ZERK CLEVIS PIN SWING FLAIL PIVOT COVER BUSHING GA BUSHING SWING FLAIL PIVOT

12 DECK ASSEMBLIES

13 GEAR BOX ASSEMBLY DECK ASSEMBLIES Page 3 PLUG /2" GAS GEAR BOX HOUSING SNAP RING MM - 25MM BOLT GEAR BOX COVER SHIM BEARING GEAR PARALLEL KEY OIL FILL PLUG SHAFT SPRING WASHER SHIM BEARING LOCK NUT PINION BEARING OIL SEAL DOUBLE LIP SEAL

14 DRIVE LINE ASSEMBLY DECK ASSEMBLIES Page 4 BEARING SET GUARD YOKE, QUICK DISCONNECT, -3/8" X 6 SPLINE CROSS & BEARING KIT YOKE, INNER TUBE YOKE, OUTER TUBE OUTER TUBE INNER TUBE ROLL PIN

15 LIFT ASSEMBLIES

16 LIFT ASSEMBLIES Page X2 WELDED CYLINDER, SLUGGED PISTON ROD CLEVIS ASSEMBLY BUTT & TUBE ASSEMBLY GLAND PISTON LOCKNUT SLUG SEAL KIT SET SCREW -2007

17 LIFT ASSEMBLIES Page X0 WELDED CYLINDER, W/2 SLUG PISTON ROD CLEVIS ASSEMBLY BUTT & TUBE ASSEMBLY GLAND PISTON LOCKNUT SEAL KIT SLUG SET SCREW -2007

18 MISCELLANEOUS ASSEMBLIES

19 MISCELLANEOUS ASSEMBLIES Page 9 BEARING - GROUND ROLLER, Rev 000 REF# PARTS DESCRIPTION TAPER BEARING TAPER BEARING RACE ROLL PIN 5/6 X -3/4 NC SHCS THRUST WASHER 2.00 OD X.26 ID CASTLE NUT /8 NPT PLUG O RING 2-7/8 OD SEAL TCM 3273TC ASSY GROUND ROLLER SHAFT SERVICE KIT, GROUND ROLLER (NOT SHOWN) GROUND ROLLER INSERT GROUND ROLLER END CAP REQ PART# TORQUE (ft-lbs) 28.7 TORQUE (Nm) 38.9

20 00% SATISFACTION GUARANTEE GET IT, LOVE IT, or LEAVE IT! 72-HOUR PARTS SHIPPING GUARANTEE