Charger, Magnum, 300C 5.7L & 6.1L Supercharger Installation Manual

Size: px
Start display at page:

Download "Charger, Magnum, 300C 5.7L & 6.1L Supercharger Installation Manual"

Transcription

1 Charger, Magnum, 300C 5.7L & 6.1L Supercharger Installation Manual Arizona Speed and Marine, Inc W. Commonwealth Ave, Chandler, AZ Phone: Fax:

2

3 1. Table of Contents 1. Table of Contents 1 2. Fuel and Spark timing Computer Programming Unit (CPU) 2 3. Warranty Information 3 4. Optional 36 Month / 36,000 mile engine Warranty 3 5. Installation Component Removal Spark Plug Installation Fuel Injector Installation Radiator Overflow Tank & Air Intake Installation Charge Cooling System & Plumbing Oil Drain Assembly Oil Feed Plumbing Throttle Body Spacer Installation Intercooler and Discharge Duct Installation Supercharger Installation Spark and Fuel Control Box and Wiring Fan & Traction Control Optional Final Inspection and Testing Operational Information Appendix Supercharger/Bracket Assembly Belt Routing Diagram Plumbing Diagram Electrical Diagram Coolant Pump Unichip Module Wiring Diagram Revision History 40 Rev B September 21,

4 2. Fuel and Spark timing Computer Programming Unit (CPU) The Unichip CPU is programmed to provide the proper spark timing and fuel enrichment under boost conditions. This additional control unit works with the stock ECU and does not effect the operation of the emission controls or demand on displacement feature of your vehicle, as designed by the manufacture. The CPU is plug-and-play, wired into the factory wiring harness and electronically resides between the cars ECU and engine. The CPU is solid state multiple highspeed processors, about the size of a MP3 player, and makes fine tuning adjustments as needed. The CPU has several advanced features to use input values from the sensors and communicates with the ECU to perform adjustment automatically. The programs are carefully designed based off dyno tested results and are to be used with factory OEM components as delivered by the vehicle manufacture. Any changes to the vehicles exhaust system or power adding components can have an effect on tune up needed by the engine. If you want to install additional performance items manufactured by Arizona Speed & Marine contact your authorized dealer to get the CPU updated with the proper program. Unichip spark and fuel management control box is warranted providing it was installed properly to be free of manufacturing defects and materials for a period of one year after the date of delivery to the original purchaser. Unichip spark and fuel map controller (CPU) has pre-programmed tables that were developed on a stock 5.7L HEMI engine and engine control module (ECU) without any modification to the vehicle. Any modifications to the stock ECU such as power programmers that increase spark timing or raise RPM limits can result in damage to your engine. Any additional modifications such as aftermarket exhaust require a different calibration. Any vehicle required for towing must also be required to have the Unichip CPU calibration modified by Arizona Speed & Marine. Arizona Speed & Marine, Inc. neither implies nor guarantees the calibration is correct for after market exhaust, towing or racing applications. Arizona Speed & Marine, Inc. does offer an optional 36,000 mile 36 month warranty on oil lubricated engine parts. To purchase the engine warranty see your dealer for details. Rev B September 21,

5 3. Warranty Information Vortech Superchargers warrantees their supercharger providing it was installed properly to be free of manufacturing defects in materials and workmanship for a period of one year after the date of delivery, to the original purchaser. Arizona Speed & Marine, Inc warrantees fuel injectors are free from defects for a period of one year after product installation. 4. Optional 36 Month / 36,000 mile engine Warranty Arizona Speed & Marine, Inc. offers an optional 36,000 mile 36 month warranty on oil lubricated engine parts. Contact your dealer or Arizona Speed & Marine, Inc. for additional information. Arizona Speed & Marine Inc. / Vortech Superchargers warranty registration must be completely filled out and registered according to the date and mileage at time of installation. Fill out the form below and return to Arizona Speed & Marine, Inc. Arizona Speed & Marine 6313 W. Commonwealth Chandler, AZ Arizona Speed & Marine, Inc. will process any claims related to the supercharger with Vortech Superchargers providing the warranty registration was filled out and processed as instructed above. Rev B September 21,

6 5. Installation Important: Read over the entire installation instruction before starting to give you a better understanding of how to install the parts. If you are missing any parts, have questions concerning the installation or need technical assistance, please call us at (480) NOTE: These instructions assume you are a qualified technician and have working knowledge of hand tools, their operation and that of the automotive engine, which you are working on. If these assumptions are not correct, it is recommended that you take the parts to a qualified facility for the installation of these parts. It is recommended you have access to a factory shop manual for installation. Arizona Speed & Marine, Inc. accepts no responsibility for improper or faulty installation of the parts, or for the accuracy or omissions in these instructions. This manual covers installation for multiple model vehicles with various engine types. Consequently, the photos shown may not represent the exact installation details for all variations. Furthermore, this supercharger kit is being continuously updated and some of the components may be different than shown in the photos. It is expected that any qualified technician will be able to understand the procedures necessary to accomplish the tasks described in the installation steps and be able to adapt the steps as needed to suit his vehicle type. Rev B September 21,

7 5.1 Component Removal Remove the negative battery cable located in the trunk Remove pans under vehicle by removing four bolts from the front and rear of the plastic pans. Then remove the row of 7MM bolts located along the front edge of the fascia Using a screwdriver or plastic rivet removal tool, remove push rivets along the inner fender well that secures the plastic pans in place. Slide pan out of the way Remove all the push rivets along the radiator support and wheel wells, these are one time use rivets, when assembling, use new rivets provided in the kit Remove the 10-mm bolts next to the fenders, these can be accessed from under the vehicle Rev B September 21,

8 5.1.6 Remove 10-mm bolt and nut located behind the headlamp Remove 10-mm nut accessible by reaching through the wheel well opening Remove 8 large push rivets from top of fascia, then remove the front fascia Rev B September 21,

9 5.1.9 Remove factory air filter box assembly from drivers side frame rail Remove factory serpentine drive belt. The belt tensioner idler pulley can be swung out of the way by using a 3/8 drive ratchet Disconnect wiring from intake air temperature sensor (IAT) and remove the sensor from the factory air intake duct. The sensor will be reused in the new supercharger intake ductwork Open radiator petcock and drain coolant Rev B September 21,

10 5.2 Spark Plug Installation Remove the 10- mm bolts and remove one coil pack Remove spark plug wire next to coil pack if necessary Remove both spark plugs Install new spark plugs and torque to 12 ft-lbs Reinstall spark plug wire and coil. 2 Plug Connections per Coil Pack Repeat process for all 8 coil packs (16 spark plugs) Rev B September 21,

11 5.3 Fuel Injector Installation New (larger) fuel injectors are supplied. These provide fuel enrichment needed to accommodate the increased air charge density from the supercharger. Spacers are installed under the fuel rail to accommodate the longer injectors on the 6.1L engine only. NO SPACERS are required for the 5.7L engine Remove screws retaining fuel rails from both sides of engine. Remove Ball Studs Unplug electrical connectors from all fuel injectors Release pressure from the fuel rail Remove clips retaining fuel rails to injectors. Unplug electrical connectors Remove old injectors and install new injectors Reinstall fuel rails. Install spacers as shown on the 6.1L engine. Spacers are not required for the 5.7L engine Reconnect all clips and electric plugs Reinstall ball studs on passenger side only. New bolts are used on drivers side as described in following sections. Spacers between Fuel Rail Tab and Manifold Rev B September 21,

12 5.4 Radiator Overflow Tank & Air Intake Installation Remove the power steering reservoir from the radiator overflow tank by pushing the locking tab towards the passenger fender and sliding the unit straight up. Remove stock overflow tank Remove the 2-10 mm bolts attaching the overflow tank Remove the clamps and both the upper and lower hoses from the overflow tank. Elevate or clamp off the lower hose to minimize coolant loss Remove the overflow tank Attach the air intake plate/welded tube assembly into the stock air intake hole just behind and below the driver s side headlight using sheet metal screws Affix the block-off plate to left inner 0 Air filter Tube Block-Off Plate 0 Rev B September 21,

13 frame with sheet metal screws Attach the air filter to the lower tube in the wheel well and affix with provided clamp Attach the supplied hose to the oil breather fitting at the oil filler neck Route the hose down to and insert on the nipple at the air intake plate. 0 Oil Filler Neck Oil Breather Hose 0 Oil Breather Hose Rev B September 21,

14 Install the new aluminum radiator overflow tank using factory screws. Power Steering Reservoir Attach both upper and lower hoses and install clamps. Use a hose mender fitting and short piece of hose to lengthen the lower hose as necessary Install a 15 length of 5/16 hose to the radiator cap vent and route it down the fender. This hose vents to atmosphere Install the power steering reservoir onto the overflow tank brackets Remove the stock thermostat and install the new 180 thermostat. Vent Hose Hose Mender Splice New 180 Thermostat Rev B September 21,

15 5.5 Charge Cooling System & Plumbing NOTE: Refer to the Plumbing and Electrical Diagrams in the Appendix for the following sections. From Pump Mounting Brackets To Intercooler Attach mounting brackets to radiator as shown with nuts and bolts. Center radiator and position it as far back as possible on the frame rail. Otherwise it will interfere with the grill. Mark and drill holes for the mounting brackets Using self-tapping screws, secure the radiator brackets to the frame rail Apply thread sealant and Install 2 brass 90 elbows in the radiator Enlarge opening in radiator support for hose clearance Install brass 90 elbows in the top and bottom of the triangular shaped reservoir using thread sealant. P-Clamp 90 Brass Elbows Rev B September 21,

16 5.5.6 Mount the circulating coolant pump to the reservoir using a rubber lined P-clamp Connect the small molded elbow from the end of coolant pump to bottom elbow of reservoir. Secure hoses with clamps Connect a 40 length of ¾ hose to the outlet side of the coolant pump and secure with clamp. Other end will be connected later Cut the existing electrical connector off the pump. Strip the ground wire and crimp an electrical ring connector to the wire. Strip the red wire and add a 7-foot piece of red wire using a splice terminal. Route the red wire to the fuse box where it will be connected later. Locate outward for air cleaner clearance Attach the mounting bracket to the top of the triangular shaped coolant reservoir Remove the three screws that secure the driver s side headlamp and swing out of the way to allow room to drill holes in the frame rail. Locate the coolant reservoir assembly to the frame rail, mark, drill and attach with sheet metal screws. Note: Locate reservoir sufficiently outboard to provide 90 Elbow space for the air cleaner. Attach the pump ground wire with one of the screws. Reinstall the headlamp Install a 90 elbow fitting to the side and a straight fitting to bottom of Straight Fitting Rev B September 21,

17 the coolant fill unit. Use thread sealant on the threads. Coolant Fill Unit Locate the coolant fill unit and bracket next to the brake reservoir as shown Locate the bracket on the fender, mark, drill holes and attach with sheet metal screws. Attach coolant fill unit to bracket Install 5 molded hose from driver s side of radiator through the firewall and up to intercooler location. Secure at radiator with clamp. Intercooler end will be attached later. Brake Reservoir Coolant Fill Bracket Cut to fit hose from bottom of coolant fill to top of coolant reservoir. Secure both ends with clamps Route hoses neatly alongside of engine and secure with tie wraps Remove screw from top left of Brake Reservoir Rev B September 21,

18 power distribution block and attach the coolant pump relay with a washer under the mounting tab of the relay. Hose from Bottom of Water Fill to Top of Reservoir Crimp a spade terminal on the red wire from the coolant pump and attach to the relay Crimp a ring terminal to one end of the in-line fuse wire and attach to the +12V lug next to fuse box Crimp a splice connector to the other end of the inline fuse wire and attach the splice to the red wire from the relay Route the yellow wire from the relay to the fuse box. Crimp a spade terminal on the wire and connect it to a fuse using an adapter terminal. Verify the connection is hot with ignition switch turned ON and OFF when the ignition switch is OFF. Trim the fuse box lip so the yellow wire is not Coolant Pump Relay Mounting Rev B September 21,

19 pinched when the cover is installed Crimp a ring terminal to the ground wire from the relay. Attach the ring terminal to the bolt at the passenger side fender well Dress wires neatly and install split sleeving over wires. Tape ends of sleeving to secure. Ring Terminal Inline Fuse Wire Connect to Switched Hot Fuse Attach to +12V Lug Trim Relay Box Lip Rev B September 21,

20 5.6 Oil Drain Assembly Drain engine oil Insert oil drain adapter into oil pan and attach the 90 AN fitting to oil drain adapter Insert nylon braided hose onto the barbed AN fitting and secure with A CV style clamp. If available, tighten clamp with crimp tool. A set of diagonal cutting pliers may also be used Route the nylon braided hose to the location of the supercharger. It is installed in the bottom of the supercharger later. 90 AN Adapter Oil Drain Adapter Braided Nylon Hose Rev B September 21,

21 5.7 Oil Feed Plumbing Remove alternator mounting bolts. Swing alternator to side to allow access to the oil pressure sending unit. Remove Alternator for access to Oil Pressure Sender Depress the release mechanism and slide the electrical connection off the oil pressure sending unit Remove Oil Pressure Sending Unit from Engine Block Remove the oil pressure sending unit using a 1-1/16 deep well socket Apply thread sealant and install the 1/8 NPT 4AN 90 elbow to the block. Be sure the elbow is tight to prevent oil leaks. Install 90 Elbow into Engine Block Rev B September 21,

22 5.7.5 Attach the 12 SS braided line to the elbow and tighten. 12 Braided Oil Line Pre-assemble the T-fitting as shown with a 45 adapter in one end and a straight adapter in the opposite end. Apply thread sealant to all pipe threads Insert sending unit through the mounting bracket and thread into the center port of the T-fitting. Use thread sealant on the threads and tighten the sending unit. 45 Adapter Straight Adapter Bolt the bracket to the engine block oriented as shown Attach the SS line coming from the engine block to the 90 elbow. Mounting Bracket Bolt Bracket to Block Attach the long SS braided line to the 45 fitting and route to the supercharger location Re-connect the electrical connector to the oil pressure sending unit. Rev B September 21,

23 5.8 Throttle Body Spacer Installation Remove the 4 throttle body bolts and remove the throttle body Position the Throttle Body Spacer against the intake manifold with the O-Ring groove facing away from the manifold NOTE: The spacer has three ports. One connects to the blowoff valve (¼ tube), one connects to the 2 Bar MAP sensor (1/8 tube). The third (upper) port may be used for an optional boost gauge or must be plugged. Install O-Ring in groove Install the O-Ring and position the Throttle Body against the Throttle Body Spacer. Install the supplied longer 10 mm bolts and tighten. CAUTION: Do not overtighten. Plugged Port 1/8 Tube Fitting ¼ Tube Fitting Rev B September 21,

24 5.9 Intercooler and Discharge Duct Installation Apply thread sealant and install one 90 elbow fitting and one straight fitting in the end of the Intercooler as shown Install the intercooler bracket, fuel rail and spacers with two bolts as shown. Spacers are only required for the 6.1L engine. 90 Elbow Fitting Intercooler Assembly Straight Fitting Attached the lower intercooler bracket to the engine using two bolts as shown. Note: The bracket is slotted to fit either the 5.7L engine or the 6.1L engines with spacers Rev B September 21,

25 5.9.4 Attach Intercooler assembly to engine. Position studs on bottom of intercooler through the support bracket. Install two nuts to the studs and tighten Cut-to-fit hose from 90 fitting at coolant filler to the 90 fitting at rear of intercooler. Attach and tighten hose clamps. See Plumbing Diagram in Appendix. Intercooler Cut-to-fit hose from the 90 elbow on driver s side of radiator to the straight fitting on the rear of the intercooler. Attach and tighten hose clamps at each end. Two Nuts Under Bracket Install two rubber sleeves and four hose clamps on the long, curved air tube. Position the long air tube between the intercooler and the throttle body. Slide the rubber sleeves onto the intercooler and throttle body. Position all Install tube, sleeves and clamps Rev B September 21,

26 clamps and tighten securely Install the Blow-Off Valve to the flange on the long curved air tube Cut-to-fit a piece of ¼ vacuum line from the throttle body spacer plate to the Blow-Off Valve Optionally, the engine cover may be trimmed to fit around the new intercooler and ducting as shown, or it may be omitted. Vacuum Hose Rev B September 21,

27 5.10 Supercharger Installation Remove the 10 mm power steering bolts and move the unit to the side Remove the auto tensioner bolt and the tensioner assembly from the front of the block Assemble the supercharger bracket and tensioner parts. Adjust tension to full loose position and leave the idler pulley bolt loose until belt tension is set. See Appendix for assembly drawing. NOTE: Do not attach supercharger to bracket until bracket is installed on engine. Remove Tensioner Power Steering Pump Rev B September 21,

28 Position the bracket assembly on the face of the engine block and bolt in place using 2 bolts 100-mm long, 1 bolt 90-mm long and 1 bolt 50- mm long. Be sure to include the small spacer between the bracket and engine block on the lower mounting bolt Reinstall the automatic tensioner Reinstall the power steering pump The supercharger is pre-aligned before shipment. However, it may be necessary to tweak the alignment to optimize final installation. Loosen the 6 clamping screws that secure the compressor to the gear case. Leave the screws snug but loose enough to allow rotation of the compressor outlet Temporarily mount the supercharger to the rear of the Small Spacer Behind Loosen 6 clamping screws to adjust clocking Rev B September 21,

29 bracket using only 2 bolts as shown. Rotate the compressor outlet so it aligns properly with the intercooler as shown in photo Remove the supercharger and tighten the 6 clamping screws Install oil drain fitting to bottom of supercharger. Attach the hose from the oil pan and install a CV boot style clamp. Crimp the clamp with crimping tool if available or use a diagonal cutting pliers for crimping Mount the supercharger to the rear of the bracket using bolts as shown. Oil Drain in bottom of Supercharger 45 Fitting Oil Input Line Apply thread sealant to the male threads of a 45 elbow fittings and thread the fitting into the oil input of the supercharger. Use a back-up wrench on the supercharger fitting to prevent over-tightening and breakage Apply thread sealant to the male threads of the 1/8 NPT to 4AN Male adapter fitting. Thread the AN fitting into the 45 elbow. Attach the SS braided oil feed line installed previously to the AN fitting. Orient the elbow down and rearward for best oil line routing Screw the SS braided oil feed line from the Oil Pressure Sensor T-Fitting onto the AN fitting and tighten. Rev B September 21,

30 Install the new belt. See Appendix for Belt Routing Diagram Adjust the manual belt tensioner until the belt is tight and the automatic tensioner is approximately in mid-position. Tighten the idler pulley bolt to lock the belt tensioner Securely tie hoses away from belt Secure the power steering pump lines away from the belt Attach the inlet tube to the rear of the supercharger and secure with clamp Attach the flexible rubber air intake hose between the inlet tube and the air filter welded tube assembly. Secure both ends with clamps Air Inlet Hose to back of Supercharger Flexible Air Inlet Hose Rev B September 21,

31 Install two rubber sleeves and four hose clamps on the short aluminum air tube. Position the tube between the supercharger and intercooler. Slide the rubber sleeves onto the intercooler and supercharger tubes and tighten clamps. Install tube, sleeves and clamps Rotate compressor to align with intercooler if necessary Rev B September 21,

32 5.11 Spark and Fuel Control Box and Wiring Remove plastic retainers and remove grill cover over PCM module. Remove plastic rivets and grill Remove bolt from bracket and remove PCM module. PCM mounting bolt Disconnect the Black C1 and Orange C2 connectors from the PCM Orange C2 Black C Rev B September 21,

33 Layout and prepare the Unichip PnP harness. NOTE: See Appendix for wiring details Plug the Black C1 and Orange C2 connectors from the vehicle harness into the Unichip Junction Box. Plug the respective connectors from the Unichip harness into the vehicle PCM Install 2 Bar MAP sensor to the engine. Cut to fit a piece of ¼ hose from the sensor to a vacuum port on the throttle spacer. Route wires to PCM area Note: Kits are supplied with various versions of MAP sensors so the picture and installation may not apply. Mount the sensor to the engine as required Rev B September 21,

34 Install the Unichip computer to the inner fenderwell using one sheet metal screw. Position the junction box and wiring in the fenderwell and then reinstall the stock PCM and cover grill Unichip Module attached to fenderwell Note: Installing the Unichip module components and all the wiring into the vehicle fenderwell can be challenging due to the space available. By carefully dressing the wiring, everything will fit neatly. Rev B September 21,

35 5.12 Fan & Traction Control Optional An optional kit is available to provide improved control of the engine cooling fan to assist cooling of the boosted engine. The kit also provides features to control the factory traction control system. Contract Arizona Speed and Marine regarding pricing and availability for your vehicle Final Inspection and Testing Re-fill engine with factory specified engine oil Re-fill engine cooling system with approved coolant Add coolant to the intercooler fill system. Add coolant slowly and toggle the ignition switch periodically to jog the pump to assist filling and purge air from the system. Check for leaks With ignition switch ON, check for fuel leaks Check all hose clamps for tightness Start the engine and let the engine warm up to operating temperature. Ensure oil has been circulated through the superchargers oiling system and there are no oil leaks Using an OBD II scan tool ensure the engines ECU displays no trouble codes and there is no timing retard present as a result of the detonation under boost pressure. If detonation is present, ensure fuel pressure is at factory specification under boost conditions and the fuel in the vehicle is fresh and has not been stored for an extended period Reassemble the front end of the vehicle by reversing the disassembly steps. Rev B September 21,

36 5.14 Operational Information It is recommended to remove the front crankshaft balancer bolt, apply Loctite or equivalent thread lock material and torque to 245 Ft-Lbs. Use minimum 91 octane fuel to minimize detonation. Do not use E85 fuel, as the fuel system cannot support the volume of fuel required under boost conditions. The OEM computer will remove timing and fuel to decrease power during gear changes, this is feature to minimize transmission wear, and is part of the torque management system. Some noise will be transmitted through the drive belt at idle when the air conditioning compressor is engaged, and will disappear in off idle conditions, this is normal. Some whining noise will be heard as the supercharger spins at higher speeds, this is normal. The lubrication system for the supercharger is supplied by the engines oil pump, and drains out of the supercharger back into the engine oil pan where it will be recirculated and filtered. Use NGK TR5-1 V power spark plugs that are a colder range than the OEM spark plugs. Use coolant in the air/liquid after cooler to prevent corrosion and freezing in cold climate. Check fuel pressure every 6 months of operation to ensure the pressure does not drop from PSI under wide open throttle. A drop in fuel pressure can lean the engine out and cause damage. Check the compression and leak down of the cylinders every 12 months of operation as a part of record keeping and maintenance. Perform maintenance on the vehicle as described in the owner s manual. Your kit is supplied with eight new fuel injectors of a larger size. The stock intake manifold is designed to move air, and keep the inlet noise down. It has a tube that extends nearly half way into the manifold from the throttle valve flange. This manifold design does not lend itself to simply install auxiliary injectors placed behind the throttle valve in the air stream. In order to get proper fuel distribution, we install larger injectors in each port as intended by the factory engineers. Rev B September 21,

37 6. Appendix 6.1 Supercharger/Bracket Assembly Rev B September 21,

38 6.2 Belt Routing Diagram Rev B September 21,

39 6.3 Plumbing Diagram Rev B September 21,

40 6.4 Electrical Diagram Coolant Pump Rev B September 21,

41 6.5 Unichip Module Wiring Diagram Rev B September 21,

42 6.6 Revision History Rev 0, Fall Initial release for Dodge Charger vehicle with 5.7L engine Rev A, April Expanded info to cover Magnum and 300C models with 5.7L and 6.1L engines. Changed header from Charger 5.7L to HEMI. Section 5: Added comment about various vehicle models and that photos may not representing all variations. Section : Changed photo showing orientation of bracket. Section 5.11: Changed mounting bolt description for intercooler bracket. Section 5.12: Changed photos and description to incorporate the Unichip Plug and Play wiring harness. Section 5.14: Added recommendation to add thread lock and torque crankshaft bolt. Section 6.4: Changed Unichip Wiring Diagram to represent Plug and Play harness Rev B, September 21, 2007 Reordered and renumbered to improve assembly efficiency. Removed references to tape thread sealant. Removed references to auxiliary fuel injectors. Section 3 & 4: Revised for clarity. Reference optional Fan & Traction Control kit. Added instructions to drain coolant. Added instructions to refill coolant. Revised instructions about supercharger installation with information for clocking compressor. Moved battery cable removal to first step. Updated photos of overflow tank. Added hose mender splice. Added instructions to install 180 thermostat. Clarified photos of throttle body spacer ports. Revised Setrab radiator mounting. Clarified oil pressure sender mounting. Added information about fuel injector spacers. Updated Plumbing Diagram. Added Supercharger/Bracket Assembly Drawing. Rev B September 21,

05-08 GT. Hellion Power Systems Mustang Kit Instructions

05-08 GT. Hellion Power Systems Mustang Kit Instructions Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo

More information

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT Part Number: 00602-17620-260 00602-17620-261 00602-17620-263 00602-17620-264 00602-17620-274 00602-17620-275 00602-17620-276 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description

More information

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,

More information

SHELBY GT500

SHELBY GT500 2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

Always wear safety glasses when working on your vehicle.

Always wear safety glasses when working on your vehicle. 90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively

More information

Edelbrock E-Force Supercharger Part #1538: Dodge 1500 Truck 5.7L V8 HEMI

Edelbrock E-Force Supercharger Part #1538: Dodge 1500 Truck 5.7L V8 HEMI Edelbrock E-Force Supercharger Part #1538: 2009-2014 Dodge 1500 Truck 5.7L V8 HEMI 2009-14 Dodge 5.7L Hemi 1500 Truck INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2009-15

More information

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side 2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and

More information

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit # 2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009

More information

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located

More information

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit 2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is

More information

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2004.5-2007 Dodge 5.9L Figure 1 - Full Kit Photo 25 Figure 2 - Hardware Kit Please read all instructions before installation. This kit is not emissions

More information

Installation Instructions

Installation Instructions 2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL F-SERIES DUAL ALTERNATOR VERSION 10/07 Blackbird Installation Supplement for Ford 6.0. Liter Dual Alternator Parts included in the 6.0

More information

V1 Truck Manifold Turbo Kit for F-body

V1 Truck Manifold Turbo Kit for F-body V1 Truck Manifold Turbo Kit for 98-02 F-body Prep: -Remove all A/C Components, Alternator and brackets, tensioner, front bumper, front bumper foam, and front bumper support. Remove radiator and cooling

More information

Special Note About The JDM High Performance Water Pump:

Special Note About The JDM High Performance Water Pump: Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering

More information

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration

More information

C40008 & C40009 EXHAUST BRAKES

C40008 & C40009 EXHAUST BRAKES EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the

More information

Phone Fax

Phone Fax Directions for Installation of ECS Paxton Supercharger Kit Disconnect battery Remove stock serpentine belt Remove stock belt tensioner, save the 2 bolts for later use on supercharger bracket Remove alternator

More information

C FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY

C FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.

More information

3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B

3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B 3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ

More information

Installation Instructions for: Radix. INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha

Installation Instructions for: Radix. INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha Installation Instructions for: Radix INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha Step-by-step instructions for installing the best in supercharger systems. ATTENTION! Your MAGNA CHARGER intercooler

More information

4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions

4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions 4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions

More information

2016+ NISSAN TITAN XD

2016+ NISSAN TITAN XD PARTS LIST AND PARTS INCLUDED 1PC MISHIMOTO INTERCOOLER 2PC SILICONE BOOTS WITH DURACORE TECHNOLOGY 4PC CONSTANT-TENSION T-BOLT CLAMPS 2PC ALUMINUM SPACERS MOUNTING HARDWARE CAUTION Never work on the cooling

More information

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L 04/05/2012 Dodge 2010-2011 6.7L Twin CP3 701-900-2356-INST Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2010-2011 Dodge 6.7L Figure 1 - Full Kit Photo 29 Figure 2 - Hardware Kit (800) 949-60002

More information

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Scion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #

Scion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6

More information

407500_ 2000 Maxima SC.doc rev.07/31/01 Page 1 of 15

407500_ 2000 Maxima SC.doc rev.07/31/01 Page 1 of 15 Materials supplied: 1- VORTECH SUPERCHARGER & MOUNTING PLATE ASSY. 1ea. Supercharger assy. with pulley 1ea. Aluminum mounting plate 2ea. M6-1.0 x 55mm bolts in plate assy. 1ea. 6-Rib drive belt 1- AIR

More information

INSTALL MANUAL D o d g e 1 2 v 6 B T A PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.

INSTALL MANUAL D o d g e 1 2 v 6 B T A PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. PN#1045310 12V Dodge Twin Turbo Kit (I-00273) 1 INSTALL MANUAL BD Twin Turbo Kit 1994-1 9 9 8 D o d g e 1 2 v 6 B T A Part# 1045310 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. * Picture as shown

More information

ENGINE DEVELOPMENT INC.

ENGINE DEVELOPMENT INC. 2003 Ford Expedition 4.6L& 5.4L We encourage you to read this manual thoroughly before you begin work, and perform the following: 1. A quick parts check to make certain your kit is complete. If you discover

More information

Edelbrock E-Force Supercharger Dodge/Chrysler 5.7L and 6.4L HEMI Part #1534, 1535, and 15350

Edelbrock E-Force Supercharger Dodge/Chrysler 5.7L and 6.4L HEMI Part #1534, 1535, and 15350 Edelbrock E-Force Supercharger 2011-2013 Dodge/Chrysler 5.7L and 6.4L HEMI Part #1534, 1535, 15340 and 15350 PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger

More information

Edelbrock Hemi Supercharger Part #1530, 1531, 1532, 1533, 1536 & 1537

Edelbrock Hemi Supercharger Part #1530, 1531, 1532, 1533, 1536 & 1537 Edelbrock Hemi Supercharger INTRODUCTION Thank you for purchasing the Edelbrock Hemi Supercharger System for various Chrysler/Dodge vehicles. The Edelbrock E-Force Supercharger System for the 2005 to 2010

More information

BD TrackMaster S D o d g e H P C R Installation Instructions

BD TrackMaster S D o d g e H P C R Installation Instructions 7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge

More information

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Installation Manual v2.2: Twin CP3 Fuel Injection Kit Dodge 5.9L

Installation Manual v2.2: Twin CP3 Fuel Injection Kit Dodge 5.9L 12/13/11 ATS Twin CP3 Kit 701-900-2272-INST Installation Manual v2.2: Twin CP3 Fuel Injection Kit 2003-2004 Dodge 5.9L Figure 1 - Full Kit Photo 26 Figure 2 - Hardware Kit 1 Please read all instructions

More information

DODGE SRT-4 PART NUMBER P (with Turbo Toys) P (without Turbo Toys) P (Stage 2 to Stage 3R Upgrade Kit)

DODGE SRT-4 PART NUMBER P (with Turbo Toys) P (without Turbo Toys) P (Stage 2 to Stage 3R Upgrade Kit) INFORMATION SHEET Stage 3R Turbo Upgrade Kit Components (1) Stage 3R PCM (4) 682 cc/min Fuel Injectors* (1) 3.0 bar MAP Sensor* (1) 3.0 bar TIP Sensor* (1) Block-off Connector for PCM (1) Mopar TD05HR

More information

Weistec M113K Supercharger System Installation Guide

Weistec M113K Supercharger System Installation Guide Weistec M113K Supercharger System Installation Guide WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 55 USES AN ELECTRONIC THROTTLE CONTROL (ETC), WHICH

More information

INSTALLATION INSTRUCTIONS FUEL RAIL

INSTALLATION INSTRUCTIONS FUEL RAIL INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:

More information

TURBOCHARGER L INSTALLATION GUIDE

TURBOCHARGER L INSTALLATION GUIDE 1 TURBOCHARGER INSTALLATION GUIDE TABLE OF CONTENTS Chapter Page 1 Intake and Cooling System Preparation 04 2 Intake Plenum and Manifold 08 3 Turbocharger Lubrication 11 4 Fuel Injectors 13 5 Re-installing

More information

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter

More information

Ford F-100 Evaporator Kit (751153)

Ford F-100 Evaporator Kit (751153) an ISO 9001:2015 Registered Company 1968-72 Ford F-100 Evaporator Kit (751153) 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

INSTALLATION INSTRUCTIONS STILLEN SUPERCHARGER KIT Nissan 350Z P/N &

INSTALLATION INSTRUCTIONS STILLEN SUPERCHARGER KIT Nissan 350Z P/N & Equipment needed: 1. Assorted sockets and wrenches 2. +,- Screwdrivers 3. Assorted pliers/ Clamps 4. Wire cutting/crimping tools 5. Thread locking compound (blue) 6. Solder gun/ shrink wrap (optional)

More information

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support: INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger

More information

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions 96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove

More information

YOU WILL BLOW YOUR MOTOR UP IF YOU MOUNT A SUPERCHARGER TO THIS KIT AND DRIVE AWAY WITHOUT INTEGRATING A RELIABLE TUNING METHOD!!!!!!

YOU WILL BLOW YOUR MOTOR UP IF YOU MOUNT A SUPERCHARGER TO THIS KIT AND DRIVE AWAY WITHOUT INTEGRATING A RELIABLE TUNING METHOD!!!!!! NOTICE This supercharger mounting kit is sold with NO supercharger head unit and is intended for use with Vortech supercharger head units exclusively. DO NOT attempt to adapt any other manufacturer s supercharger

More information

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM

More information

Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589

Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589 Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589 INTRODUCTION Edelbrock 5.0L Ford Supercharger System Thank you for purchasing the Edelbrock 5.0L Ford Supercharger System for the Mustang GT. The

More information

Keeping You Cool Under Pressure

Keeping You Cool Under Pressure Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal

More information

Slingshot Rotrex Supercharger Kit

Slingshot Rotrex Supercharger Kit Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you

More information

SALEEN SERIES VI SUPERCHARGER FOR MUSTANG

SALEEN SERIES VI SUPERCHARGER FOR MUSTANG SALEEN SERIES VI SUPERCHARGER FOR 2005-07 MUSTANG MAINTENANCE SCHEDULE Very little maintenance is required for your Series VI supercharger. There are two key fluids involved in the kit which you should

More information

Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS

Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for install Jack Jack

More information

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support: INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger

More information

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,

More information

Edelbrock E-Force Supercharger. Part #1538: Dodge 1500 Truck 5.7L V8 HEMI

Edelbrock E-Force Supercharger. Part #1538: Dodge 1500 Truck 5.7L V8 HEMI Edelbrock E-Force Supercharger : 2009-2014 Dodge 1500 Truck 5.7L V8 HEMI 2009-14 Dodge 5.7L Hemi 1500 Truck INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2009-15 Dodge

More information

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE

More information

ALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions

ALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions ALL AMERICAN BILLET Front Drive System - Small Block Ford Installation Instructions Small Block Ford with AC & PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for

More information

Edelbrock E-Force Supercharger Ford F L Lincoln Mark LT 5.4L Part #1581

Edelbrock E-Force Supercharger Ford F L Lincoln Mark LT 5.4L Part #1581 Edelbrock E-Force Supercharger 2004-08 Ford F-150 5.4L Part #1581 INTRODUCTION Thank you for purchasing the Edelbrock 5.4L Ford Supercharger System for the 2004-2008 F-150 and 2006-2008 Lincoln Mark LT.

More information

INTERCOOLED SUPERCHARGER SYSTEM FORD 5.4L 3V F-150 TRUCK

INTERCOOLED SUPERCHARGER SYSTEM FORD 5.4L 3V F-150 TRUCK Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2004-2006 FORD 5.4L 3V F-150 TRUCK Step-by-step instructions for installing the best in supercharger systems. 89-89-65-001 Rev C Magnuson

More information

JBR MAZDASPEED

JBR MAZDASPEED Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps

More information

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace

More information

Z06 Corvette Lingenfelter High Flow Air Intake

Z06 Corvette Lingenfelter High Flow Air Intake 2006-2007 Z06 Corvette Lingenfelter High Flow Air Intake LN4233 1557 Winchester Road Decatur, Indiana 46733 260 724 2552 phone 260 724 8761 fax www.lingenfelter.com Parts List # Part number Description

More information

SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2 SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2 WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 63 USES AN ELECTRONIC THROTTLE

More information

SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT

SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT = SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,

More information

LChevrolet Camaro Supercharger Kit

LChevrolet Camaro Supercharger Kit PART #92000A Important Notes: 2010-2013 6.2LChevrolet Camaro Supercharger Kit The use of fuel additives (ie. octane boosters) is not recommended. There is a possibility that these chemicals can damage

More information

Edelbrock E-Force Supercharger JEEP WRANGLER JK 3.6L V6 Part #1527 and 15270

Edelbrock E-Force Supercharger JEEP WRANGLER JK 3.6L V6 Part #1527 and 15270 Edelbrock E-Force Supercharger 2012-14 JEEP WRANGLER JK 3.6L V6 Part #1527 and 15270 INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the Jeep Wrangler with 3.6L V6 Pentastar.

More information

Performance Inlet Manifold

Performance Inlet Manifold Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with

More information

INSTRUCTIONS E36 SUPERCHARGER WITH C38 BLOWER.

INSTRUCTIONS E36 SUPERCHARGER WITH C38 BLOWER. INSTRUCTIONS 1996-1999 E36 SUPERCHARGER WITH C38 BLOWER. 1 Introduction Congratulations on your purchase of an Active Autowerke Supercharger, and welcome to the AA Tuning family. Your supercharger kit

More information

SALEEN SPEEDLAB SUPERCHARGER

SALEEN SPEEDLAB SUPERCHARGER SALEEN SPEEDLAB SUPERCHARGER R INSTALLATION MANUAL: 1999-2000 Mustang 4.6L 2V Saleen Performance, Inc. 1225 East Maple Rd. Troy, MI 48083 248-743-4800 www.saleen.com Saleen Speedlab Supercharger Installation

More information

Shotgun Single Barrel HPFP install guide

Shotgun Single Barrel HPFP install guide Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective

More information

ENGINE ASSEMBLY STOCK TO 250 HP

ENGINE ASSEMBLY STOCK TO 250 HP GM SPORT COMPACT Performance Build Book 25 ENGINE ASSEMBLY STOCK TO 250 HP Fig. 3 The stock ECOTEC engine has proven reliable to 250 hp.(fig. 3) Performance upgrades are available from GM Performance Parts

More information

All cores due 30 days after invoice date - no credit after 60 days.

All cores due 30 days after invoice date - no credit after 60 days. NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.

More information

Installation Instructions for: Radix. Intercooled Supercharger System GM 4.8L & 5.3L SUV S Only

Installation Instructions for: Radix. Intercooled Supercharger System GM 4.8L & 5.3L SUV S Only Installation Instructions for: Radix Intercooled Supercharger System 07-10 GM 4.8L & 5.3L SUV S Only Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED *

More information

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS #TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When

More information

MAZDASPEED3 Intercooler Instructions

MAZDASPEED3 Intercooler Instructions MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through

More information

Edelbrock E-Force Supercharger Dodge 1500 Truck 5.7L V8 HEMI Part #1538

Edelbrock E-Force Supercharger Dodge 1500 Truck 5.7L V8 HEMI Part #1538 Edelbrock E-Force Supercharger 2009-2014 Dodge 1500 Truck 5.7L V8 HEMI INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2009-14 Dodge 1500 Truck with 5.7L V8 Hemi. The utilizes

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT 2008 GM 2500 AND 3500 6.6 DURAMAX DIESEL VERSION 5-08 Parts Included in Installation Kit Before beginning installation, check the parts kit thoroughly against the parts

More information

Installation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output)

Installation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output) Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output) PN L300080607 Revision - 1.1 Lingenfelter Performance Engineering

More information

Shotgun Double Barrel HPFP install guide

Shotgun Double Barrel HPFP install guide Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective

More information

Installation manual BMW E TS1/TS2

Installation manual BMW E TS1/TS2 Installation manual BMW E46 330 TS1/TS2 Technical support Europe: +4741558555 Technical support USA: (858)314-2954 Email support: support@esstuning Installation manual BMW E46 330 TS1/TS2 Remove and send

More information

These instructions were written for reference only and the use of a factory service manual is recommended.

These instructions were written for reference only and the use of a factory service manual is recommended. Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2 CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2 WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 63 USES AN ELECTRONIC THROTTLE

More information

Installation Manual for VMAC System V900095

Installation Manual for VMAC System V900095 Installation Manual for VMAC System V900095 GMC/Chevrolet 1999 2002 6.0L Sierra and Silverado CK2500 and CK3500HD General Information... 3 Before You Start... 3 Additional Requirements... 4 Part 1: Preparing

More information

Installation Instructions for: Toyota 4Runner and FJ Cruiser

Installation Instructions for: Toyota 4Runner and FJ Cruiser Installation Instructions for: 2010-2017 Toyota 4Runner and 2010-2014 FJ Cruiser Step-by-step instructions for installation of the supercharger system. * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION! Your

More information

Single Barrel Shotgun HPFP Install Guide

Single Barrel Shotgun HPFP Install Guide Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should

More information

G2 INSTALLATION MANUAL

G2 INSTALLATION MANUAL PERFORMANCE ENGINEERED SYSTEMS G2 INSTALLATION MANUAL FOR RACING OR OFF ROAD USE 1 INTRODUCTION PLEASE PURCHASE AUDI- ONLY POWER STEERING FLUID (PENTOSIN CHF 11S) Please note this an older version, and

More information

Installation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output)

Installation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output) Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output) PN L300090607 Revision - 1.1 Lingenfelter Performance Engineering

More information

SLP Camaro ZL1 STAGE 3 (650 HP)

SLP Camaro ZL1 STAGE 3 (650 HP) SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

Edelbrock E-Force Supercharger Complete Competition Ford Mustang 5.0L Part # s: 15896

Edelbrock E-Force Supercharger Complete Competition Ford Mustang 5.0L Part # s: 15896 Edelbrock E-Force Supercharger Complete Competition Part # s: 15896 Introduction Thank you for purchasing the Edelbrock Complete Competition Supercharger System for the 2011-2013 5.0L Ford Mustang GT.

More information

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi These instructions are based on a vehicle with an OEM turbocharger and top-mount intercooler. If a front-mount

More information

Installation Instructions for: RAM 5.7 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM

Installation Instructions for: RAM 5.7 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM Installation Instructions for: 2014-2015 RAM 5.7 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL REQUIRED *

More information

Edelbrock 5.4L F-150 Supercharger Part #1583

Edelbrock 5.4L F-150 Supercharger Part #1583 Edelbrock 5.4L F-150 Supercharger INTRODUCTION Edelbrock 5.4L Ford Supercharger System Thank you for purchasing the Edelbrock 5.4L Ford Supercharger System for the F-150. The Edelbrock E-Force Supercharger

More information

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following

More information

These instructions were written for reference only and the use of a factory service manual is recommended.

These instructions were written for reference only and the use of a factory service manual is recommended. Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The

More information

LSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body)

LSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) LSX Intake Manifold #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) Thank you for your purchase of the most innovative and powerful Gen III (LS1 and LS6) manifold ever developed. We are

More information

ADM Performance 6079 Mapleshade Lane Dallas, Texas (214)

ADM Performance 6079 Mapleshade Lane Dallas, Texas (214) 1) Disconnect Battery Ground 2) Raise front end of Vehicle FAN INSTALL INSTRUCTIONS 3) Remove lower Radiator hose and drain coolant into a pan. (you will reuse coolant later) 4) Remove Air Intake piping

More information

FAX

FAX INSTALLATION INSTRUCTIONS 6299 Air Suspension Kit (pat. pending) 2009+ Dodge 1500 Pickup with Rear Coil Springs Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY

More information