ASSA ABLOY MPI (Infinite Hold Open Range) Support Unit Models. Multi-Point Electromechanical Overhead Concealed Closer Holder Releasing Device
|
|
- Arleen Daniel
- 3 years ago
- Views:
Transcription
1 Overhead Concealed Closer Holder Releasing Device with Rigid Slide Arm For wood or metal doors 1-3/4 to 2-1/4" (45-57mm) thick Hung in a hollow metal frame Standard butt hinges Typical Installation One track & closer position for all door opening angles Easy arm attachment Removable Frame Stop Required*-Not Shown Support Unit Models 7290 MPI (Infinite Hold Open Range) 7290 MPS (Selective Hold-Open Range) CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment. Hinge or Pivot Left Hand Door-LH Right Hand Reverse-RHR Right Hand Door-RH Left Hand Reverse-LHR Hinge or Pivot *Not required when frame rabbet exceeds 2-3/16" (56mm). Norton is a registered trademark of Yale Security Inc., an Group company. Copyright 2002, 2014 Yale Security Inc., an Group company. All rights reserved.
2 Model 7290MPI/7290MPS Overhead Concealed With Rigid Slide Arm Templa- te Standard Butt Hinges Viewed From Above 4 Holes for Closer Fasteners 3/8 (9.5) 2 (50.8) 3/8 (9.5) 2 (50.8) 22-1/4 (565.2) 23 (584.2) 1-1/4 (31.8) 7/8 Dia. Hole (22.2) (Conduit) 1" (25.4) 20-1/4 Ref. (514.4) C L Conduit Conduit Box Dust Box (By frame mfr.) Reinforcement (By frame mfr.) 1/8 Ref. (3.2) C L Closer 5/32 to Centerline (4.0) Of Conduit Hole C L 3-3/4 (95.3) 1" (25.4) 1" (25.4) C L Hinge Viewed From Above 11/16 (to edge of cutout) (17.5) 8 (203.2) 24 (609.6) 21 (533.4) Frame Reinforcements 14 (355.6) 4 Holes for Track Fasteners 22 (558.8) 3/8 (9.5) deep cutout in shaded area 24 (609.6) 1-1/4 (31.8) 5/8 (15.9) Removable Frame Stop (By frame mfr.) 1-3/16 3/8 C L Door and Track Min. 1-3/4 (44.5) Max. 2-1/4 (57.2) (30.2) LEFT HAND DOOR 1/8 (3.2) Hinge 1/4 (6.4) C L Door and Track (9.5) 2-1/2 (63.5) NOTES: Do not scale drawing. Left hand door shown. Hardware dimensions shown (not cutouts). Dimensions are in inches (mm). Minimum door width 27" (685.8). Track 24" (609.6) long. Maximum width hinge is 5" (127). Fastener Use Preparation 1/4-20 machine screw #14 wood screw Track Installation Door Angle With Cushion and stop block metal frame and metal door wood door Without Cushion and Stop block #7 (.201" dia.) or 5.10mm. drill 1/4-20 tap 7/32" or 5.5mm. drill Auxiliary Door Stop Required Opening greater than 110º See installation sequence on pages 4 & 5. Norton is a registered trademark of Yale Security Inc., an Group company. Copyright 2002, 2014 Yale Security Inc., an Group company. All rights reserved. Page 2
3 Model 7290MPI/7290MPS Overhead Concealed With Rigid Slide Arm Hinge Components Closer Assembly Cam Plug (MPS Unit only) Plug (MPS & MPI Unit) Conduit Box Cover Conduit Knockout (5) Dress Plate Mounting Screws 6-32 x 3/8 long L S S/D P B Spring Tube Conduit Box Short Dress Plate Positioning Screw Self Clinching Studs Mounting Plate Track Cushion and Stop Block Arm Flat Washer with countersink (4) Mounting screws x 5/8 long (4) Track screws 1/4-20 x 7/16 or x 1-1/4 long wood screws (2) Arm/track screw 1/4-20 x 3/4 long Hex drive with thread lock Long Dress Plate Arm Slider This end of slider (short side) toward cushion and stop block. Align Squares Stud Slider Screw Pack Norton is a registered trademark of Yale Security Inc., an Group company. Copyright 2002, 2014 Yale Security Inc., an Group company. All rights reserved. Page 3
4 Installation Sequence Note: Read instructions entirely prior to installation. Door/Frame Prep: Determine hand of door from illustration on page 1. Closer are handed. Hand of closer must match hand of door. Using template dimensions on page 2, locate holes and cutouts in frame and door, unless a separate template has been supplied for your application. Door: Prepare door for track. Drill and tap (4) holes for 1/4-20 machine screws. Frame: Prepare the frame for mounting closer. Drill and tap (4) holes for 1/4-20 machine screws or #14 wood screws Note: Generally on new construction hardware cutouts are made by suppliers at their shop. Wiring: Wiring of switch must be in compliance with N.E.C. Class 2 wiring specifications. Voltage to unit must be the same as shown on the unit: 24 Volts AC/DC or 120 Volts AC, 60hz. Voltage must be within a range of plus 10% and minus 15% of the unit's stated voltage. Pull hook-up box off mounting plate's self clinching studs, disconnect plugs and remove hook-up box cover. TEST SWITCH Terminal Block (+) (-) VI FUSE 0.75 AMPS (+) (-) 3 2 ALARM PANEL 1 DOOR HOLDER CIRCUIT Anchor conduit at 1 or 2 hook-up box knockouts. Secure power input leads to terminal lock, positions #1 and #2 as shown. SPECIFICATIONS 120VAC 24VAC 24VDC Voltage Current 132V MAX. 102V MIN. 26.4V MAX. 20.4V MIN. 120V 24V 24V 26.4V MAX. 20.4V MIN..035 AMPS.070 AMPS.070 AMPS OPTIONAL SELECTIVE HOLD OPEN SWITCH SOLENOID COIL FUSE Test switch (Push) Pos. (+) Black Neu. (-) white Reconnect sockets a. Connect plug with white leads from solenoid for MPI and MPS units. b. Connect plug with black leads from cam switch if used. Replace hook-up box cover and secure with (2) screws. Reattached hook-up box to mounting plate by aligning (2) holes at bottom of hook-up box with (2) self clinching studs. See illustration on page 3. Norton is a registered trademark of Yale Security Inc., an Group company. Copyright 2002, 2014 Yale Security Inc., an Group company. All rights reserved. Page 4
5 Installation Sequence con't Determine door opening angle See page 2 and below. Series 7290MPI: Infinite Hold Open units will hold door at virtually any degree of door opening from 5 to 175. Series 7290MPS: Selective Open Hold units are shipped with hold open set at approximately 85. Hold open can be set from 5 to 175. The hold open position can be increased or decreased by loosening the cam screw, rotating the cam to the new setting and tighten cam screw. See chart below for cam settings where hold open range will start. Align letters on hold open cam with V centerline of switch rocker. Choose row of letters on cam that are closest to the hinge side face of door. Mount closer to frame. Position spring tube away from hinge and mounting plate flush with frame rabbet. Secure to frame reinforcements with (4) 1/4-20 x 5/8 screws. Use care to avoid damaging or pinching wires. Install arm on closer pinion (see illustration below) Position arm counterbore facing down with index mark aligned with pinion index mark. Install onto pinion. Secure with washer and flat head arm screw with thread lock (see page 3). Left hand Arm in position (Bottom View) Pinion Mark Arm Index Mark Right hand Setting G H J K L M Door Angle 15º 30º 45º 60º 90º NOTE: Verify setting of cam before mounting closer to the frame. 135º Install track in door. Place the assembled track into door cutout with open side up, cushion andstop block if used, toward the hinge. Move slider to the opposite end of track (see illustration, page 3). Secure track with (4) 1/4-20 machine screws. Connect arm to track. Open door to approximately 5" (127mm), rotate arm to slider and place end on stud. Use a screw driver to align the square on slider s stud with the arm square (see illustration on page 3). Push down on arm to seat stud and to prevent stud from rotating. Secure with arm/track screw, 1/4-20 x 5/8 long flat head hex drive with thread lock. Norton is a registered trademark of Yale Security Inc., an Group company. Copyright 2002, 2014 Yale Security Inc., an Group company. All rights reserved. Page 5
6 Model 7290MPI/7290MPS Overhead Concealed With Rigid Slide Arm Closer Adjustment CAUTION: Do not back valves out of closer or a leak will result. Standard Door Closer Door Closing Controls "L" Range "S" Range Door Opening Controls "BC" Range Never Close Completely Closing Power Adjustment MODEL SIZE HAND RH LATCH SWEEP BC POSITION BC INCREASE POWER ADJUST DECREASE Mounting Base Plate Closing Controls Opening Controls Latch Sweep Delayed Action Backcheck Closer Controlsaccessible through mounting plate for closer adjustment: Use 1/8" (3mm.) hex-key for valve adjustments. Use standard screwdriver for power adjustment. Power Adjustmentpermits increasing door closing force. Controlled by slotted screw marked "P.A." Closing Speedcontrolled by valves marked "SWEEP" and "LATCH". Attention: Adjust closing speed time to between 4 to 7 seconds from 90. Use of the door by handicapped, elderly, or small children may require greater closing time. Backcheckcushions or slows the opening of a door that is forced to travel faster than conditions require. Backcheck controlled by valves marked "BC POSITION" (open for backcheck start at a greater door opening angle) and "BC" (for adjusting backcheck intensity). Never close "BC" valve completely. Optional Enhanced Backcheckprovides adjustable backcheck intensity beginning at approximately 15 of the door opening cycle. Backcheck positioning valve is omitted when this feature is provided. Hold Open Check. Turn power to the unit On. Open door to the hold open position. Manually pull door out of hold open and release, door should close. FUSE Test switch (Push) Pos. (+) Black Neu. (-) white Hook-Up Box Testing. Open door to the hold open position. Depress Test Switch button on Hook-up Board, accessible through cutout in hook-up box and mounting plate (see illustration at right). Door should close. Install short and long dress plates with (5) 6-32 screws Highway 74 East Monroe, NC Tel: (877) Fax: (800) Norton is a registered trademark of Yale Security Inc., an Group company. Copyright 2002, 2014 Yale Security Inc., an Group company. All rights reserved. Page 6
Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO
Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions
Series 9540 J9540. Installation Instructions Multi-Sized 1 to 6 Non-Hold Open. Regular Arm Applications. Parallel Arm Applications
Series 940 J940 ASSA JL940 ABLOY Installation Instructions Multi-Sized to 6 Non-Hold Open Regular Arm Applications Left Hand Regular Arm Application Contents Page Template Template with 984-8 Drop Plate
Installation Instructions Series 78-B/FHA Hold Open
Installation Instructions Series 78-B/FHA Hold Open Traditional Style Door Closers Read these instructions before proceeding with the installation. Make sure that the door opens the full angle desired
Hinge (Pull) Side Door Application DC6230 Series Multi-Sized 1 thru 6 DC6430 Series Half-Size 1 thru 6. Door Mounted DC6230 & DC6430
Installation Instructions Universal Door Closers Slide Track Application (0 Maximum Door Swing) (standard)- N.H.O. Bumper Stop A - H.O. Bumper Stop Track - Pull Side See pages 2 & Hinge (Pull) Side Door
7100SZ Series SafeZone Installation and Instruction Manual
7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 80-9371-0081-00 (10-10) Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 5 for template) 3 1 Push Side Applications
ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
Concealed overhead closer for high-end applications DOOR CLOSERS CATALOG
Concealed overhead closer for high-end applications 7900 S E R I E S DOOR CLOSERS CATALOG INTRODUCTION The 7900 Series Overhead Concealed Closers offer extremely durable operation with the vandal resistance
ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
Installation Instructions (07-08) CAUTION
Hinge Edge of Hinge Edge of 7500 eries Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should
Installation Instructions CAUTION
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
ASSA ABLOY Universal Door Closers
Installation Instructions For Non-Hold Open or A Hold Open Arm Options DC6200 Series DC6400 Series Multi-Sized thru 6 Half-Size thru 6 Regular Arm Parallel Arm Universal Door Closers Jamb Mount See pages
DC3210 Series. Multi-Sized 1 thru 6 DEEP REVEAL APPLICATION WITH M103 OPTION(615F59 CLAMP KIT) Recommended Closer Size
DC310 Series Multi-Sized 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH DEEP REVEAL APPLICATION WITH M103
5600 Series Power Operator Installation and Instruction Manual
5600 Series Power Operator Installation and Instruction Manual 80-956-000-00 (08-) 5 ASSA ABLOY 6 Item No. Description Motor (5600M) Cover (5600COV) Control Inverter (5600IN) Power Supply VDC (5600PS)
ASSA ABLOY Series Multi-Point Hold Open Installation and Instruction Manual
Pull Side Applications with Slide Track (7210, 7250) (see page 7 for template) 7200 Series Multi-Point Hold Open Installation and Instruction Manual 3 1 Push Side Applications with Double Lever Arms (7220,
ASSA ABLOY Universal Door Closers with Heavy Duty Spring Stop Parallel Arms
DC610 Series Multi-Sized 1 thru 6 DC610 Series Half-Size 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH
7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor
7100SZ Series SafeZone Multi-Point Closer/Holder with Motion Sensor INTRODUCTION Designed with safety in mind, SafeZone takes door closers to a higher level. SafeZone uses a multi-point, electromechanical
7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor
7100SZ Series SafeZone Multi-Point Closer/Holder with Motion Sensor Page Revised Electronically 8/11 7100SZ Series SafeZone INTRODUCTION Designed with safety in mind, SafeZone takes door closers to a higher
5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY
5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY 80-957-000-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 6 5 0 8 7 9 Item No. Description Back plate Door Closer
TS93 EMF T/PT/TDE. Surface applied door closer
TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress
5700 Series Power Operator Stop (Push) Side Mount Installation and Instruction
5700 Series Power Operator Stop (Push) Side Mount ASSAManual ABLOY Installation and Instruction 80-957-0005-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 5 6 0 8 7 9 -/8 () Item No. Description Back plate Door
TS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall)
TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall) TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer
7100SZ SERIES. Multi-Point Closer/Holder with Motion Sensor
safezone Multi-Point Closer/Holder with Motion Sensor introduction Designed with safety in mind, SafeZone takes door closers to a higher level. SafeZone uses a multi-point, electromechanical closer and
*24771* 4040SE DE Sentronic. 1 Voltage. 7 Regulation. 2 Track. 8 Door Closer Cover. 3 Spring Power. 4 Arm Installation. 5 Arm Screw.
*2477* 2477 SE Egress 4040SE DE Sentronic Installation Instructions This closer features mounting options for both standard and step-down double egress frames. Before beginning, determine which type of
TS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH)
Surface applied door closer Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) TABLE OF CONTENTS Technical specifications Size selection chart 2 Closer setup
Multi-point closer/holder with motion sensor 7100SZ DOOR CLOSER CATALOG
Multi-point closer/holder with motion sensor 7100SZ S E R I E S DOOR CLOSER CATALOG INTRODUCTION The 7100 Series SafeZone door closer safeguards occupants throughout a variety of facilities with the detection
Power drill Center punch Wire stripper
Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 7 for template) 7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 3 1 Push Side Applications with Double Lever
Electromagnetic Door Holder/Releases
Electromagnetic Door Holder/Releases Table of Contents introduction Rixson offers a wide range of electromagnetic door holders/releases. Designed for virtually any remote door release application, electromagnetic
Installation Instructions
eft Hand Door H ight Hand everse H ight Hand Door H eft Hand everse H ight Hand Door H eft Hand everse H egular rm ee Page Top Jamb ee Page 5 Parallel rm ee Pages & Instructions CUTION n Incorrectly installed
These door closers should NOT be installed on the exposed side (weather side) of exterior doors.
500 Series Non-Hold Open Door Closer Instructions vailable in Sizes,, and 5 Regular rm See Page n incorrectly installed or improperly adjusted door closer can cause property damage or personal injury.
ROFU TJ 152-A. Y ALE SECURITY GROUP 50BC Series Door Closer. 50BC Series Door Closers. Sizing Chart for Installations. Ordering Information
ROFU 50BC Series Door Closers Specifications U.L. Listing All Yale 50 Series Door Closers with non-hold-open arms are listed by Underwriters Laboratories, Inc. for use on labeled fire doors. Tri-Pack Closer
* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION
*921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications
*24213* 4040-SE Sentronic. 1 Voltage. 6 Adjusting Hold-Open Door Position. 7 Regulation. 2 Tracking. 8 Door Closer Cover.
*223* 223 00-SE Sentronic Installation Instructions This closer features two mounting options. Before beginning, determine which type of mounting best applies to your application, or had been specified
FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE
FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke barrier doors.
Closer with traditional styling for low to moderate traffic openings 78-B/F DOOR CLOSER CATALOG
Closer with traditional styling for low to moderate traffic openings 78-B/F S E R I E S DOOR CLOSER CATALOG Introduction The 78-B/F Series is a surface closer with traditional styling that offers multiple
78-B/F Series. Traditional Door Closers
78-B/F Series Traditional Door Closers introduction The Norton Series 78-B/F Traditional Surface Closers represent a combination of traditional styling and modern closer features. All closer sizes are
*24191* 4040SEL Sentronic. 35 ft-lbs 48 N-m 62 N. Installation CAUTION. Customer Service. Installation Instructions
*24191* 24191 4040SEL Sentronic Installation Instructions Backcheck = Maximum Opening Force 35 ft-lbs 48 N-m 62 N Latch Backcheck Main To Increase Power 5/32 Hex Wrench Main Latch 1a 1b 1c 1d This closer
KEANE MONROE a member of the record group
SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke
9540 SERIES. Cast Iron Door Closer
Cast Iron Door Closer Introduction The Norton 9540 s provide an ideal retrofit solution for retail, office, government and other commercial facilities. Certified to ANSI/BHMA Grade 1 requirements for long
Multi-sized cast iron closer for high use applications DOOR CLOSER CATALOG
Multi-sized cast iron closer for high use applications 9500 S E R I E S DOOR CLOSER CATALOG INTRODUCTION Ideal for high use openings, the Norton 9500 Series Cast Iron door closer offers the durability,
* * Maintenance Kit
*941079-00* 941079-00 Maintenance Kit Page: TOC-1 Table of Contents Description: Page Number: Pictorial Index to Parts (immediatey follows Table of Contents )...PIP-1, PIP-2 1. Center Case Parts Insert-98/99
HIGH SECURITY CLOSERS SERIES
HIGH SECURITY CLOSERS SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide
HOW TO TELL HAND OF DOOR:
*15022* 4410ME Series 15022 Door closer with electronic release & Multi-point hold open Installation Instructions 1 Closer Installation 1a Closer Information Closer is handed at the factory. The hand of
HIGH SECURITY SERIES
HIGH SECURITY SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide is based
51 Series Door Closers. An ASSA ABLOY Group brand
51 Series Door Closers An ASSA ABLOY Group brand Introduction CONTENTS Features & Benefits...3 Overview...4 Fasteners...4 Features...5 Finishes...6 How to Order...7 Applications...8 Technical Details...9-11
*ININST.1002* 1690 Touchbar. Index:
*ININST.1002* ININST.1002 Concealed Vertical Rod Panic Device 1690 Touchbar Installation Instructions Index: : The door prep for the 1690 Hex Bottom Rod is different than for the RL bottom rod. Please
Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG
Full-featured operator with slim profile for moderate to high traffic applications 6300 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The Norton 6300 Series Low Energy Operator offers a broad set
6900 PowerMatic Low Energy Power Operator Installation Instructions CAUTION CAUTION WARNING
CUTION 80-99-0110-00 (09-08) 900 PowerMatic Low Energy Power Operator Installation Instructions Hinge (Pull) Side of Door Installation for Door Openings 8 to 110 Use Series 910 Rigid rm and Slide Track
WARNING: Make sure that (120V, 60Hz) input power is turned off at facility s main circuit breaker before proceeding with installation.
6000 Series Operator Installation and Instruction Manual ASSA ABLOY 6020 1 7 (up to 110 opening) 3 4 5 6 6030 2 (110 to 180 opening) 5 8 Item No. Description 1 2 Motor (6000M) Cover (6000COV) 3 4 Control
D O O R C L O S E R S
DOOR CLOSERS DOOR CLOSER Philadelphia Hardware Group, Inc. is presenting the finest ADVANTAGE surface mounting door closers certified by BHMA including: Multi-size door closer: 9000, 8000, 6000, 6000S
51 Series Door Closers. An ASSA ABLOY Group brand
51 Series Door Closers An ASSA ABLOY Group brand Introduction contents Features & Benefits...3 Overview...4 Fasteners...4 Features...5 Finishes...6 How to Order...7 Applications...8 Technical Details...9-11
8000 Series Tri-Style Non Handed Door Closer
8000 eries Trityle Non Handed Do Closer eft Hand Do H ight Hand everse H eft Hand Do H ight Hand everse H eft Hand Do H ight Hand everse H egular rm ee Page ee Page 5 Parallel rm ee Pages 3 & 4 Instructions
Connected To Control Box Series. Closer. Set Screw. Arm Screw. Right Hand Shown. 1/8" I.D. Air Inlet Tubing Connected To Control Box
*19963* 19963 Auto-Equalizer Low Energy Door Operator 1/8" I.D. Air Inlet Tubing Connected To Control Box Closer 2610 Series Set Screw Arm Screw Track Roller Track Installation Instructions Top Of Door
626F Exit Device Trim Installation Instructions
626F Exit Device Trim Installation Instructions For use with all Yale 7000, 2100, 1800 and 1500 Series Exit Devices (Wood and Metal Doors) Attention Installer Any retrofit or other field modification to
Installation Instructions. Non Hold Open Models. Sized (Sizes 2,3,4,5) Weaker BC 9303BC 9304BC 9305BC. Stronger +
O Right Hand RH eft Hand Reverse HR eft Hand H Right Hand Reverse RHR eft Hand H Right Hand Reverse RHR Regular rm ee Page Top Jamb ee Page Parallel rm ee Pages 3 & UTION Instructions Non Hold Open Models
CONCEALED CLOSER SERIES
CONCEALED CLOSER SERIES APPLICATIONS n For aluminum, hollow metal, or wood doors and frames. n Can be used with hinge or pivot mounted door. n Closers for 4 or minimum 1-3/4 head frame or 4 top rail. n
9000 Series Trinity The world's most intelligent door closer
9000 Series Trinity The world's most intelligent door closer INTRODUCTION Designed for doors that are subject to changing conditions, the Norton 9000 Series Trinity offers customers an intelligent door
D o o r C l o s e r s
Door Closers DOOR CLOSER Philadelphia Hardware Group, Inc. is presenting the fi nest ADVANTAGE surface mounting door closers for your various application demands. There are Multi-size door closer: 9000,
Norton ABS-AMERICAN BUILDING SUPPLY, INC Series Multi-Sized Closers - Packed 6 per case
ABS-AMERICAN BUILDING SUPPLY, INC. 1601 Series Multi-Sized Closers - Packed 6 per case Features Two Power Ranges: Each series can be adjusted through a range of sizes: Series 1601 Normal Power Range Closers,sizes
ARCHITECTURAL DOOR HARDWARE DOOR STOPS & HOLDERS THRESHOLDS & GASKETING CATALOG
ARCHITECTURAL DOOR HARDWARE DOOR STOPS & HOLDERS THRESHOLDS & GASKETING CATALOG January 1, 2017 v3 West Coast Office (800) 544-4422 East Coast Office (800) 225-6737 intldoorclosers.com Index DOOR STOPS
CONCEALED CLOSER SERIES
CLOSER SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of
Headline. Overhead Door Holders/Stops
Headline Overhead Door Holders/Stops Quality hardware for superior door control 2 Glynn-Johnson has been providing the highest quality door control hardware for 75 years. Known in the industry as the overhead
Copyright , 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express
over he ad conce aled closer s o v e r h e a d c o n c e a l e d c l o s e r s i n t r o d u c t i o n i n t r o d u c t i o n Rixson Overhead Concealed closers offer an aesthetically appealing way to
2904 Power Supply Installation Instructions I-EA00041
FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and
ASSA ABLOY. 7100SZ Series SafeZone External Sensor. Installation and Instruction Manual ASSA ABLOY. Patent Pending
700SZ Series SafeZone External Sensor Installation and Instruction Manual Patent Pending.76 (0). (79.8) Tools required:.0 (0.8) Allen wrench set (inch) Flat blade screwdriver (potentiometer & terminal
7570 SERIES Security Door Closer
7570 SERIES Security Door Closer INTRODUCTION Norton High Security Closers are designed for use in prisons, government buildings, schools, financial institutions, or any installation where vandalism, abuse,
DOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM
SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of the closer.
CRAFTMASTER HARDWARE CO., INC Architectural. Product Guide
Architectural Product Guide INTRODUCTION Norton Door Controls offers a comprehensive line of door controls designed and manufactured to ensure superior performance, reliability and application breadth.
Door Closers. DC8000 Series
Door Closers DC8000 Series Introduction Applications High-quality product and innovative design are the foundations of Corbin Russwin s long history and reputation. That tradition continues with the new
* * M400 Series. Features. Models. Trims. UL Requirements. Single Electromagnetic Locks: M420, M450, M490. Installation Instructions
*44487296* M400 Series 44487296 Single Electromagnetic Locks: M420, M450, M490 Installation Instructions M420/M450 Armature plate assembly M490 Armature plate assembly Features Automatic Voltage Selection
D-1610/D-1611 SERIES: DOOR CLOSERS. D-1610/D-1611 Series. Door Closers. Trusted experts. Proven reliability. Simply STANLEY.
D-1610/D-1611 SERIES: DOOR CLOSERS D-1610/D-1611 Series Door Closers Trusted experts. Proven reliability. Simply STANLEY. TABLE OF CONTENTS General Information...2, 3 Standard Application...4 Parallel
6900 Series PowerMatic Low Energy Power Operator
6900 Series PowerMatic Low Energy Power Operator INTRODUCTION Norton's 6900 Series PowerMatic is a low energy power door operator designed to automatically open and close doors with a lower energy opening
An ASSA ABLOY Group brand Series. Architectural Door Closer
An ASSA ABLOY Group brand 3000 Series Architectural Door the perfect choice The Yale 3000 Series Architectural Door s offer the perfect combination of reliability, appearance and durability in today s
*ININST.1039* 2390 Touchbar
*ININST.1039* ININST.1039 Concealed Vertical Rod Panic Device 2390 Touchbar Installation Instructions Index Parts List... 2 Before Installation... 5 Installation... 5 RX Device Wiring... 12 EL Device Wiring...
Superior door control for rigorous, high-use applications 6000 LOW ENERGY OPERATOR CATALOG
Superior door control for rigorous, high-use applications 6000 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The 6000 Series low energy operator is a heavy-duty unit designed for rigorous, high-use
ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-8 Features: ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS Filtered/Regulated 24 Volts DC Up to Full 2 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit
High Security Closers Series
High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can
JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
Series. Non Hold Open Door Closers Parallel Arm. * conditions permitting. Parts. Mark and Drill Holes. Installation Sequence.
Instructions CUTION n Increctly installed improperly adjusted do closer can cause property damage personal injury. These installation instructions should be followed to avoid the possibility of misapplication
High Security Closers Series
High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can
RTS88. Overhead Concealed Door Closer
RTS88 Overhead Concealed Door Closer RTS88 OVERHEAD CONCEALED CLOSER DORMA RTS88 OVERHEAD CONCEALED DOOR CLOSER Invisible door control Dependable and easy to install Architects are often challenged to
5300 Series 5300 SERIES
5300 Series Hager 5300 Series Grade 1 door closer is ideal for schools, hospitals, and other high abuse and high traffic environments. It is constructed of an aluminum alloy and provides smooth door control.
MAx-305 & MAx-318 Series MAx-405 Through MAx-419 Series Two-Position Actuators
MAx-305 & MAx-38 Series MAx-405 Through MAx-49 Series Two-Position Actuators General Instructions Application For two-position operation of dampers, valves, and other equipment which require the return
6900 Series PowerMatic. Low Energy Power Operator
6900 Series PowerMatic Low Energy Power Operator INTRODUCTION Norton's 6900 Series PowerMatic is a low energy power door operator designed to automatically open and close doors with a lower energy opening
9700/F9700 SERIES RIM EXIT DEVICE
INSTALLATION INSTRUCTIONS 9700/F9700 SERIES RIM EXIT DEVICE Index: Screw chart Tools required Outside trim options "03" Additional door prep Device installation Options available 5300 retro-fit preparation
NON-SIZED SIZED HANDED
4410ME SERIES TOP JAMB (PUSH SIDE) MOUNTING The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.
S6100 SERIES REVERSIBLE PANIC/FIRE EXIT RIM DEVICES INSTALLATION INSTRUCTIONS
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com S6100 SERIES REVERSIBLE PANIC/FIRE EXIT RIM DEVICES INSTALLATION INSTRUCTIONS These instructions
KAWNEER 1686 EL CONCEALED EXIT DEVICE
FEBRUARY, 2012 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl
DC3000 Series. Door Closers
Door Closers Table of Contents Applications 2 Features 3 & 4 Mountings 5 & 6 Door Closer Arms 7 & 8 Mounting Brackets 9 Brackets and Covers 10 Size and Handing 11 How to Order 12 Quick Codes 13 Helpful
DC5000 Series. Cam Action Door Closer
Series Cam Action Door Closer Introduction Table of Contents Introduction...2 Features... 3 Mountings... 4 Accessories... 5 How to Order... 6 Quick Codes... 6 Helpful Terms... 7 Specifications... 8 Applications
268, 269 & 278. Concealed Door Closers
268, 269 & 278 Concealed Door Closers Copyright 2004-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents General Information....3 268 Features and Benefits...4
LCN 4310ME SERIES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled. closer/holder designed to provide
HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide FEATURES infinitely adjustable hold-open for fire and smoke barrier doors. Door
Multi-feature closers with compact design, ideal for application on interior doors DOOR CLOSER CATALOG
Multi-feature closers with compact design, ideal for application on interior doors 1700BC E R I E DOOR CLOER CATALOG 1700BC ERIE LIGHT COMMERCIAL DOOR CLOER INTRODUCTION Norton 1700BC eries Door Closers
An ASSA ABLOY Group brand. 400/4400 Series. Institutional Door Closer
An ASSA ABLOY Group brand 400/4400 Series Institutional Door Closer the engineer s choice Yale s 400/4400 Series Institutional Door Closers offer customers the ideal combination of superior performance,
Patient Care Facility
ISIMET Patient Care Facility DLA Controller Individual Room Configuration Style 1 W/ Ver 4.41 pcb & Pulse Relay pcb Installation, Operations, Start-up and Maintenance Instructions Meets all Standards for
Drug Testing Labs. Style 2 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions
ISIMET Drug Testing Labs DLA Controller Style 2 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions Meets all Standards for Canadian Industrial Control
NON-SIZED SIZED HANDED
4040SE SERIES n Standard 4040SE Series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks are optional,
*28101* 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT. Table of Contents.
*28101* 28101 4630, 4640 Electric Auto Equalizer Series 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT Table of Contents General Information...2
LCN 4310ME SERIES FEATURES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled
HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for FEATURES fire and smoke barrier doors. Door