2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID:
|
|
|
- Clyde Chambers
- 5 years ago
- Views:
Transcription
1 xtooltipelement Service Information 2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID: Engine Front Cover Replacement Removal Procedure 1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. 2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement. 3. Install the engine support fixture. Refer to Engine Support Fixture. 4. Remove the drive belt. Refer to Drive Belt Replacement. 5. Drain the cooling system. Refer to Cooling System Draining and Filling. 6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. 7. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement. 8. Remove the lower belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Lower. 9. Remove the engine oil pan. Refer to Oil Pan Replacement. 10. Lower the vehicle. 11. Remove the left belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Left Side.
2 12. Remove the right engine mount bracket bolts (2 4). 13. Remove the right engine mount bracket (1). 14. Remove the water pump. Refer to Water Pump Replacement. 15. Remove the thermostat bypass hose adapter. Refer to Thermal Bypass Fitting Replacement. 16. Remove the radiator outlet hose from the engine front cover. Refer to Radiator Outlet Hose Replacement. 17. Remove the engine front cover bolts (2 4). 18. Remove the engine front cover (1).
3 19. Remove the engine front cover gasket (1). 20. Clean the engine block and front cover gasket sealing surfaces. Installation Procedure 1. Apply sealer to the lower tabs of the engine front cover gasket. Refer to Adhesives, Fluids, Lubricants, and Sealers for the correct part number. Uniformly apply the sealer to both sides of the gasket lower tabs with the sealant bead being no less than 5.0 mm (0.20 in) wide as shown. Torque front cover immediately after installation of sealer coated gasket.
4 2. Install the gasket (1) to the engine block positioning the gasket on the locating pins (2). 3. Install the engine front cover (1) to the engine block aligning the cover with the locating pins. Notice: Refer to Fastener Notice. 4. Install the engine front cover bolts (3, 4). the bolts to 55 Y (41 lb ft). 5. Install the engine front cover bolts (2). the bolts to 27 Y (20 lb ft). 6. Install the radiator outlet hose to the engine front cover. Refer to Radiator Outlet Hose Replacement. 7. Install the thermostat bypass hose adapter. Refer to Thermal Bypass Fitting Replacement. 8. Install the water pump. Refer to Water Pump Replacement.
5 9. Install the right engine mount bracket (1). 10. Install the right engine mount bracket bolts (2 4). the bolts to 55 Y (41 lb ft). 11. Install the engine mount bracket bolts (3). the bolts to 25 Y (18 lb ft). 12. Install the left belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Left Side. 13. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. 14. Install the engine oil pan. Refer to Oil Pan Replacement. 15. Install the lower belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Lower. 16. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement. 17. Lower the vehicle. 18. Install the drive belt. Refer to Drive Belt Replacement. 19. Remove the engine support fixture. 20. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement. 21. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. 22. Fill the cooling system. Refer to Cooling System Draining and Filling. You are about to leave the website of General Motors and view the content of an external website. That website is not owned or controlled by, or affiliated with General Motors or its subsidiaries, and it is subject to its separate terms and conditions and other agreements, as well as its privacy policies. General Motors cannot be held responsible for the content of external websites. OK
6 Cancel Warning 2018 General Motors. All rights reserved.
Page 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative
Control Solenoid Valve and Transmission Control Module Assembly Replacement Removal Procedure
xtooltipelement Service Information 2010 Cadillac CTS CTS VIN D Service Manual Transmission Automatic Transmission - 6L45/6L50/6L80/6L90 Repair Instructions - On Vehicle Document ID: 2103542 Control Solenoid
Water Pump Replacement (L4)
2011 Chevrolet Equinox Equinox, Terrain VIN L Service Manual Water Pump Replacement (L4) Special Tools EN-43651 Water Pump Holding Tool For equivalent regional tools, refer to Special Tools. Removal Procedure
2001 Chevrolet Corvette V8-5.7L VIN G
1 of 14 2/21/2013 10:34 AM 2001 Chevrolet Corvette V8-5.7L VIN G Vehicle» Engine, Cooling and Exhaust» Engine» Oil Pan» Service and Repair Oil Pan Replacement Removal Procedure 1. 2. 3. Remove the front
The numbers below refer to the step numbers on the diagnostic table.
xtooltipelement Service Information 2004 Chevrolet C Silverado - 2WD Sierra, Silverado VIN C/K Service Manual Body Wipers/Washer Systems Diagnostic Information and Procedures Document ID: 815265 Wipers
Vehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
Lower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
Water Pump Replacement (L4)
1 of 9 9/5/2017, 3:07 PM 2014 Chevrolet Captiva (VIN C) Antara, Captiva Service Manual 5565211 Engine/Propulsion Engine Cooling Repair Instructions Document ID: 2643411 Water Pump Replacement (L4) Special
1994 Ford Mustang - Engine Mechanical > Engine Mechanical Components > Timing Chain Cove...
Page 1 of 6 1994 Ford Mustang : Engine Mechanical > Engine Mechanical Components > Timing Chain Cover & Seal > Removal & Installation > 5.0L Engine 5.0L Engine 1. Disconnect the negative battery cable
1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
CYLINDER HEAD REPLACEMENT - R... CYLINDER HEAD REPLACEMENT - RIGHT SIDE (ENGINE MECHANICAL - 4.8L, 5.3L, AND 6.0L) Document ID#
CYLINDER HEAD REPLACEMENT - R... CYLINDER HEAD REPLACEMENT - RIGHT SIDE (ENGINE MECHANICAL - 4.8L, 5.3L, AND 6.0L) Document ID# 1524388 Cylinder Head Replacement - Right Side Tools Required J 42385-200
2014 Dodge Challenger R/T. The water pump (1) is mounted directly to the timing chain cover and is equipped with a non serviceable integral pulley.
Fig. 73: Water Pump A centrifugal water pump (2) circulates coolant through the water jackets, passages, intake manifold, radiator core, cooling system hoses and heater core. The pump is driven from the
Cylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
2012 Chevrolet Volt Chevrolet Volt Owner Manual Document ID:
xtooltipelement Service Information 2012 Chevrolet Volt Chevrolet Volt Owner Manual Document ID: 2263658 Jump Starting Jump starting is connecting jumper cables between the two vehicles to enable vehicle
Oil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
1 of 8 12/12/2012 6:08 PM 1999 Chevrolet Express - 2WD Express, Savana VIN G Service Manual Engine Engine Mechanical - 6.5L Repair Instructions Engine Replacement Removal Procedure Tools Required J 36857
Small Block Chevrolet Serpentine Drive System with & without Power Steering
an ISO 9001:2008 Registered Company Small Block Chevrolet Serpentine Drive System with & without Power Steering 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-3113 www.vintageair.com
This information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773
1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
2000 Nissan Altima SE
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses,
Engine Oil Cooler Hose/Pipe Replacement (4WD)
Page 1 of 9 1998 Chevrolet Blazer - 4WD Blazer, Bravada, Jimmy, S10 Pickup, Sonoma (VIN S/T) Service Manual Engine Engine Mechanical - 4.3L Repair Instructions Document ID: 179331 Engine Oil Cooler Hose/Pipe
Timing Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
Vehicle Level Engine, Cooling and Exhaust Cooling System Water Pump Service and Repair Removal. Removal
1 of 7 4/5/2008 11:18 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1994 Jeep Truck Wrangler L6-242 4.0L VIN S MFI Conversion
MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner
Page 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
HOLLEY LS-SWAP WATER PUMPS WATER PUMP INSTALLATION INSTRUCTIONS FOR GM LS-ENGINE APPLICATIONS:
HOLLEY LS-SWAP WATER PUMPS WATER PUMP INSTALLATION INSTRUCTIONS FOR GM LS-ENGINE APPLICATIONS: Holley LS- Swap cast water pumps are designed for street/performance applications and provide optimum performance
Some customers may comment on one or more of the following conditions: These conditions may be caused by one or all of the following:
xtooltipelement Service Information 2007 GMC Truck Envoy - 2WD Envoy, Rainier, TrailBlazer, Ascender VIN S/T Service Manual Body Systems Fixed and Moveable Windows Schematic and Routing Diagrams Document
Ford 6.8L, w/spider, 2000+
DewEze Aiir Compressor Kiit 700554 Ford 6.8L, w/spider, 2000+ INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Drain the radiator. 3. Remove the air cleaner assembly. 4. Remove the upper radiator
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
![1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6](/thumbs/95/124411779.jpg "1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6")
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
1999 Nissan Altima GLE
TIMING CHAIN CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves. NOTE: Following procedure
SECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY.
SERVICE V8 XJ Series DATE 12/02 TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump 100-21 MODEL 2002 MY V8 XJ Series VIN F44114 - F55936 Issue: Some 2002
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
OIL PUMP (G306709) DISCOVERY 3, ENGINE - TDV6 2.7L DIESEL SPECIAL TOOL(S) Crankshaft Front Seal Remover PUMP - OIL - RENEW
2005.0 DISCOVERY 3, 303-01 ENGINE - TDV6 2.7L DIESEL OIL PUMP (G306709) IN-VEHICLE REPAIR 12.60.26 PUMP - OIL - RENEW 2700 CC 4.3 USED WITHINS SPECIAL TOOL(S) 303-1120 Crankshaft Front Seal Remover 303-1122
Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 1 Technical Service Bulletin # 98-107 Date: 990111 Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009 Reference:
2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
WATER PUMP INSTALLATION INSTRUCTIONS WEIAND WATER PUMPS ACTION PLUS & TEAM G APPLICATIONS FOR SMALL BLOCK & BIG BLOCK CHEVROLETS
WATER PUMP INSTALLATION INSTRUCTIONS WEIAND WATER PUMPS ACTION PLUS & TEAM G APPLICATIONS FOR SMALL BLOCK & BIG BLOCK CHEVROLETS APPLICATIONS: Weiand Action Plus aluminum water pumps are designed for street/performance
2014 RAM C/V Tradesman
Fig. 91: Suction Hose Ball Valve NOTE: View typical 14. Open the suction hose's ball valve to begin refilling the cooling system. 15. When the vacuum gauge reads zero, the system is filled. NOTE: On some
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
ALLDATA Online - 1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L - Servi... Page 1 of 22 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
![1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder](/thumbs/95/123571962.jpg "1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder")
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43
Page 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
Front Fog Lamp Package Installation
Page 1 of 9 2016 Chevrolet Colorado (VIN 4) Colorado, S10, Trailblazer Accessory Installation Manual Accessories Electrical Accessories Accessories Document ID: 2671978 Front Fog Lamp Package Installation
Exhaust Manifold - Remove and Install
14 RENR7458-09 i02228217 Exhaust Manifold - Remove and Install SMCS Code: 1059-010 Illustration 25 g01124147 1. Apply ing (A) to the outside diameter of the male ends of exhaust manifold (2). Assemble
Engine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
PARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
Disconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
Big Block Chevrolet Serpentine Drive System with & without Power Steering
an ISO 9001:2008 Registered Company Big Block Chevrolet Serpentine Drive System with & without Power Steering 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-3113 www.vintageair.com
Draining and Filling Cooling System
2001 Chevrolet Impala Draining and Filling Cooling System Ethylene glycol/water fill ratios have been established to ensure a minimum of 50 percent ethylene glycol. Ensure that all the engine block drains
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
Intake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
1.6L 4-CYL - VIN [E]
![1.6L 4-CYL - VIN [E]](/thumbs/81/84172348.jpg "1.6L 4-CYL - VIN [E]")
1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES
TSI Date Group No. Supp. Page
Volvo Trucks North America, Inc. Greensboro, NC USA Timing Gear Cover TSI Date Group No. Supp. Page 11.2001 215 006 1(7) Timing Gear Cover D12C Fig. 1: VOLVO D12C Engine W2003244 This information covers
DISASSEMBLY. 1. INSTALL ENGINE TO ENGINE STAND FOR DIS- ASSEMBLY 2. REMOVE CYLINDER HEAD (See page EM 29)
DISASSEMBLY EM67 EM9Q0. INSTALL ENGINE TO ENGINE STAND FOR DIS- ASSEMBLY. REMOVE CYLINDER HEAD (See page EM9). REMOVE WATER BYPASS PIPE Remove the nuts, bolts, water bypass pipe and gasket.. REMOVE THERMOSTAT
Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
SECTION 1D2 M161 ENGINE COOLING
SECTION 1D2 M161 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
Removal Procedure. Remove the timing chain tensioner. 1 of 32 12/17/ :42 AM
1 of 32 12/17/2011 11:42 AM Removal Procedure 1. 2. 3. 4. 5. 6. Remove the camshaft cover. Raise and support the vehicle. Remove the No. 1 cylinder spark plug. Rotate the crankshaft in the engine rotational
5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS
5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
2/25/2018 Engine, 4.0l Cylinder Head Removal 2008 Chrysler Town and Country (4.0L) - RT MotoLogic
2008 Town and Country (4.0L) - RT REMOVAL - CYLINDER HEAD(S) Labor Operations: Click to display a list of Labor Operations associated with this procedure Special Tools: Click to display a list of tools
TIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
FUEL PUMP CAMSHAFT TIMING CHECK
PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,
EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
Engine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
Distributor Replacement
Page 1 of 11 2002 Chevrolet Chevy K Silverado - 4WD Sierra, Silverado (VIN C/K) Service Manual Document ID: 690165 Distributor Replacement Removal Procedure Notice: There are two procedures available to
Page 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover
ALLDATA Online Buick Truck Rendezvous V6-3.4L VIN E - Draining and Fillin... Draining and Filling Cooling System
Page 1 of 8 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Buick Truck Rendezvous V6-3.4L VIN E Conversion Calculator Vehicle
3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT
Part Number: 00602-17620-260 00602-17620-261 00602-17620-263 00602-17620-264 00602-17620-274 00602-17620-275 00602-17620-276 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description
1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
Small Block Ford Serpentine Drive System with & without Power Steering
an ISO 9001:2008 Registered Company Small Block Ford Serpentine Drive System with & without Power Steering 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-3113 www.vintageair.com
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
IN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
Timing Chain: Service and Repair
1996 Nissan-Datsun Truck D21 Hardbody 2WD L4-2389cc 2.4L SOHC MFI (KA24E) Copyright 2013, ALLDATA 10.52 Page 1 Timing Chain: Service and Repair *** THIS ARTICLE INCLUDES UPDATES MADE BY TSB 95027, DATED
IN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION
EG1485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1486 EG1487 EG1488 OIL PUMP REMOVAL (See Components for Removal and Installation) HINT: When repairing the oil pump, the oil pan an^ strainer should