Epoxy and Rilsan Coated Aluminum. Low Cost Corrosion Resistant Long Cycling Life. Features

Transcription

1 PDF Published January 0, 7 PA Series Pneumatic Actuators Chemline PA Series are quarter turn pneumatic actuators for all sizes of ball and butterfly valves. These actuators are epoxy and Rilsan coated for high corrosion resistance and long cycling life. Normal working temperatures are - o C to 90 o C. They may be actuated with air, water, natural gas or nonaggressive fluids up to 0 psi pressure. P Series is one in a range of actuators specially selected for ball and butterfly valves. Hardware kits are available for mounting of actuators in the field. Chemline also offers complete actuated valves, fully assembled and bench tested. Your Pipeline To Quality Epoxy and Rilsan Coated Aluminum SERIES: PASR PADA CONTROL PRESSURE: to 0 psi OUTPUT TORQUES : Up to 0,6 in.-lb. and 5, in.-lb. Low Cost Corrosion Resistant Long Cycling Life Features Long Cycling Life Rated for million cycles Self-lubricating Rilsan coating on inner contact surfaces for better wear than epoxy coating or anodizing Self-lubricating O-Rings Double O-Ring Shaft Seals Minimal backlash with no play in parts Massive tooth engagement between racks and pinion Corrosion Resistant* Low friction coefficient Rilsan coating inside and out for very smooth and durable finish as well as outstanding chemical and abrasion resistance Application Diversity Normal working temperatures are - o C to 90 o C Can be actuated with air, water, natural gas or non-aggressive fluids up to 0 psi pressure Standard ISO and NAMUR Dimensions Permits easy mounting of control accessories to actuator and of actuator to valve Standardized mounting kits/brackets are readily available Compact, Simple Design Double piston, double rack and pinion design supplies constant torque output Balanced Internal Forces High torque-to-weight ratio All porting is integral Concentric Nested Springs Standardized ISO Bolt Pattern for mounting to valve Standardized ISO Bolt Pattern for mounting to valve Standard NAMUR dimension Shaft and Bolt Pattern for mounting limit switch box or positioner Standard NAMUR Pad for flush mounting of solenoid valve PA Series on Type True Union Ball Valve Position Indicator PA Series on Type 57 Butterfly Valve Largest unit will power up to 4". Largest unit will power up to 8". * See page for details of coating process/specs. 0/07 Chemline Plastics Limited 7 Chemline is a registered trade mark of Chemline Plastics Limited

2 PA Series Pneumatic Actuators Self Lubricating Rilsan Coating Double O-Ring Shaft Seals Standard ISO Bolt Pattern for mounting to valve Self Lubricating O-Rings PROPERTIES OF THE COATING PROCESS The aluminium actuator bodies and end caps undergo a 4-step pre-treatment to guarantee a perfect finish and superior corrosion resistance. The next step is painting by cationic electro deposition (cataphoresis). A 0 micron layer of hydro soluble priming paint is applied to create the smoothest possible base coat for the Rilsan coating. OPERATION Pressure to Port A moves pistons inward, turning output shaft 90 o clockwise, as viewed from top of actuator. Pressure to Port B moves pistons outward, compressing springs (on spring return models only) and turning output shaft 90 o counter-clockwise, as viewed from top of actuator. The final step is the application of a 0 micron thick coat of Rilsan polyamide. Rilsan is a fully polymerized thermoplastic which provides outstanding corrosion resistance to effluents, sea water, sea mist, hydrocarbons, solvents and a large number of chemicals. It has excellent mechanical and physical properties, exceptionally smooth finish, extremely low friction coefficient which ensure a longer cycling life than competitors products. EIGHTS, AIR CONSUMPTIONS AND CYCLE TIMES eight Lbs. Air Consumption Open Port A Close Port B Cycle Time (Sec.) Open Port A Close Port B eight Lbs. Air Consumption (Standard Cubic Inches) Cycle Time (Sec.) Open Port A Close Port B PADA PASR PADA PASR PADA PASR PADA PASR PADA PASR PADA PASR PADA PASR PADA PASR PADA PASR PADA PASR

3 PA Series Pneumatic Actuators K A B J L N M F E Q øc ød BOTTOM VIE DETAIL P H (ISO-5) T R /4" NPT.7" O Port A Closed I BOTTOM SHAFT DETAIL G S U 0.95" 4 M5 TOP VIE DETAIL M5 Port B Open NAMUR MOUNTING PAD TOP SHAFT DETAIL 4 DIMENSIONS INCHES DA SR PADA PASR PADA PASR PADA05 PASR05 PADA0 PASR0 PADA5 PASR5 PADA0 PASR0 PADA5 PASR5 PADA0 PASR0 PADA PASR PADA PASR A SR B DA Bottom Mount Detail C D Dia. Thread Depth Dia. Thread Depth.65 (F04).97 (F05).97 (F05).97 (F05).97 (F05).97 (F05).76 (F07).76 (F07) M (F07).76 (F07).76 (F07).76 (F07) 4.0 (F0) 4.0 (F0) 4.9 (F) 5.5 (F4) M0 M0 M Bottom Shaft Detail E F G H I DIMENSIONS INCHES DA SR J PADA PASR PADA PASR PADA05 PASR05 PADA0 PASR0 PADA5 PASR5 PADA0 PASR0 PADA5 PASR5 PADA0 PASR0 PADA PASR PADA PASR Top Shaft Detail K L (ISO-) 0.4 (ISO-) 0.4 (ISO-) 0.4 (ISO-) 0.4 (ISO-) 0.4 (ISO-) 0.4 (ISO-) 0.4 (ISO-) (ISO-4) (ISO-4) M N O P Q R S T U

4 PA Series Pneumatic Actuators 9 0 a b PARTS Recommended Spare Parts No. Part Pcs. Materials a Snap Ring to5 Steel coated b Allen Screw 0 04 SS to 6 04 SS to 5 Aluminum Alloy coated Cap 0 to Aluminum Alloy coated and cataphoresis Cap O-Ring to Nitrile Buna-N 4 Piston to 5 Polyarilamide 0 to Aluminum Alloy 5 Cylinder to Aluminum Alloy coated and cataphoresis 6 asher to Polyamide 6 7 Spring Clip Stainless Steel to 0 Steel coated with Nickel-PTFE to Steel coated 8 Position Polyacetal Indicator to 0 Polyamide to Polypropylene 9 Piston Guide to 5 Polyacetal 0 to 4 PTFE-Bronze 4 Nylon PARTS No. Part Pcs. Materials 0 Guide Ring Polyacetal + Mb to 5 Polyacetal 0 to PTFE-Bronze Piston O-Ring to 5 Nitrile Buna-N 0 to 4 Nitrile Buna-N Upper Shaft to Nitrile Buna-N O-Ring Lower Shaft to Nitrile Buna-N O-Ring 4 Springs Set to DIN-7-C coated 5 to 5 Aluminum Alloy coated Cap 0 to Aluminum Alloy coated and cataphoresis 6 Shaft Polyamide and SS Insert to 0 0 SS 5 to Steel coated 7 Gear 0 to Aluminum Alloy coated 8 ater Tightness 0 to Nitrile Buna-N Plane Gasket 9 Threaded Pin 0 to 04 SS Recommended Spare Parts

5 TORQUE DOUBLE ACTING INCH POUNDS Model No ,47 0,045,60 5,757 4,9 5,67 0 Supply Pressure (psi) Model No. PADA0 PADA5 PADA0 PADA PADA 978,74,804 7,4,57,4,4,789 9,549 6,697,689,948 4,770,96, ,8,8 4,708 8,0 80 Supply Pressure (psi) PADA PADA PADA05 PADA0 PADA ,87 PA Series Pneumatic Actuators TORQUE SPRING RETURN INCH POUNDS Model No. Number of Springs Start Start End Spring 60 Supply Pressure (psi) PASR PASR PASR05 End Start End 80 Start End Start End 0 PASR0 PASR5 PASR0 PASR5 PASR0 PASR PASR 4 5* ,97,57 8,5,799,4,47 4, 5,569 6,787,049 5,84 7,9 0, , ,46,59,566,785,89 4,5,80,049 4,574 6, ,5, ,,975,560, 5,56 4,4,95,780 0,5 9,5 7,78 5, , ,975,490,7 8 4,69,, , 7,80 5,07,697 Start End , , ,8,75,48,0,04,957,544,96 7,98 6,760 5,77 5, 4,860,648,8 0, ,09, ,958,47,990,66 7,0 5,54,977,764,6,5 9,7 6, ,467,4,95,,75,,058,94 4,87,9,57,8 0,0 9,78 8, 7,60 9,88 7,98 6, ,9, ,65,964,578,0,94,455,97, 9, 7,960 6,99 5,8 7,968 5,846,709 0, ,,47,09,,698,55,476,98,678,547 4,9 4,5 4,65,597 0,56 0,0,4 0,790 8, ,09, 90 8,45,9,0,57,97,0 4,48,957,4 0,78 8,8 7,60 0,80 8,046 4,690 * Standard Spring set.

6 P Series Accessories SOLVDA is a CSA/UL- Approved 5/-way pilot-operated, bubble-tight solenoid valve designed to mount directly to any NAMUR-compliant actuator. Its complement of features includes a reinforced polyamide body; nitrile seals and o-rings; nickel plated ports and mounting hardware; epoxy encapsulated coil; threaded actuator and pilot vent ports; manual override; easy AC/DC interchangeability; low minimum main air line pressure operation due to high Cv factor; breather block capability; multi-million cycle life and -pin DIN connection in conduit, grommet and LED grommet versions.0-0vac/60- Hz supplied standard; 0-VAC/60-Hz, VAC, 4VAC, VDC, 4VDC and explosion-proof units also available on request. PLSYT4 is a CSA-approved -position limit switch box designed for standoff mounting to any VDI/VDE845 (NAMUR) compliant rotary actuator. Its complement of features includes a quick-access cover; high visibility position indicator/beacon; compact design; quick-setting switch cams; million-cycle single-pole double-throw switches; dual electrical inlets for solenoid and/or ground connections; vapor-tightneess and submersibility. It is most effective in on-off applications on spring-return actuators but is available with any number of options, including hazardous area enclosures, intrinsical safety, reed or inductive proximity switches and BUS communication modules. F/R-A is an effective -piece air filter/regulator with pressure gauge. Its complement of features includes a brass body; Acetal valve components; Nitrile bushings/o-rings; polycarbonate filter bowl and polyethylene filter element; manual filter bowl drain valve. It is available with x /8" gauge ports so the gauge can be oriented correctly, regardless of airflow direction. The additional port is capped off. MO-Series is a manual declutchable gear override designed to fit between any ISO-compliant valve and rotary actuator. It offers simple and reliable manual positioning of valves, dampers and other quarter-turn devices when overriding existing pneumatic actuators. All MO units are suitable for indoor and outdoor use and combine rugged construction, light weight and modular design to provide the most efficient and cost-effective solution to a full range of manual override requirements. The self-locking worm gear design means safe and easy operation, positive manual positioning and extremely long life. The MO-series override can be adapted to any quarter-turn actuator and may even be installed in the field on existing valves. POS-Series positioners are designed to mount directly to any VDI/VDE845 (NAMUR) compliant rotary actuator. Its complement of features includes die-cast aluminum enclosure; inlets for electrical, air and gauge connections; visual position indication; and a temperature rating of -0ºC to 70ºC. It is available in - 5 psi pneumatic, 4-0 ma electro-pneumatic, digital or BUS communication versions. It can be fitted with extra mechanical or proximity switches and a potentiometer for position feedback.

7 PA Series Accessories END CAP TRAVEL STOPS Two adjustable bolts are integrated into the actuator end caps and act as travel stops for the open travel only. These bolts act as stops for both pistons to apply balanced stopping pressure and are adjustable for the full length of travel. INTEGRAL TRAVEL STOPS Two adjustable bolts are integrated into the actuator body and act as travel stops for both the open and close travel. These bolts act as stops for a cam mounted onto the output shaft and are adjustable for the last 5 degrees of travel. RETAINED SPRING SET The Retained Spring Set is used to keep the spring sets from overextending and causing a sudden release of spring tension during actuator end cap removal, which could lead to actuator damage or personal injury. This system is available as an option only on larger actuators, where the spring tension is greater and an added safety factor can be favourable. OPTION ITEM NUMBERS LP-S LP-05S LP-0S LP-5S LP-0S LP-5S LP-0S LP-S LP-S End Cap Travel Stops LP- LP-05 LP-0 LP-5 LP-0 LP-5 LP-0 LP- LP- Integral Travel Stops TR0 TR5 TR0 TR TR Retained Spring Set SM0 SM5 SM0 SM SM

8 P Series Pneumatic Actuators PP Series Plastic * The plastic body units compliment Chemline valves in an all-plastic actuated valve package. PG Series 80 o Rotation * These half turn actuators are designed to operate all sizes of -way ball valves. These actuators are epoxy and Rilsan coated for high corrosion resistance. SIZES 0 0 PPDA PPDA PPDA0 PPDA0 Operating Torque ,4 PPSR PPSR PPSR0 PPSR0 Operating 80 psi air Operating Torque Spring End Air Start SIZES PGDA0 PGDA0 PGDA0 Operating Torque 7,866 PGSR0 PGSR0 PGSR0 Operating 80 psi air Operating Torque Spring End Air Start 6 8,08 P Series Stainless Steel * These actuators are designed to withstand highly corrosive environments, underwater and marine applications. Normal working temperatures are - o C to 90 o C. They may be actuated with air or non-aggressive fluids up to 0 psi pressure. PH Series High Temperature * These actuators are designed to operate in ambient temperatures up to 65 o C on kilns, boilers, furnaces, process vessels and heat exchangers. They are actuated by air or non-aggressive fluids up to 0 psi pressure. SIZES PDA Operating Torque 0 PSR 0 PDA0 57 PSR0 0 PDA0,4 PSR0 0 PDA0,789 PSR0 * Dimensions are similar to PA Series. See individual data pages for specifics. Operating 80 psi air Operating Torque Spring End ,59 Air Start ,99 SIZES PHDA PHDA0 PHDA0 PHDA0 PHDA PHDA Operating Torque 0 57,4,789 9,549 6,697 PHSR PHSR0 PHSR0 PHSR0 PHSR PHSR Operating 80 psi air Operating Torque Spring End ,44 4,5 6,4 Air Start ,56 6,764 6,80 55 Guardsman Road, Thornhill, Ontario, Canada, LT 6L Tel: info@chemline.com Fax: Your Pipeline To Quality Valves, Piping, Flow Meters and Controls