SE8300 Series Installation Guide 24 Vac Low Voltage
|
|
- Harold Richardson
- 5 years ago
- Views:
Transcription
1 SE00 Series Installation Guide Low Voltage mercial and Hotel/Lodging HVAC Fan Coil Applications CONTENTS Installation Terminal Identification & Function Terminal identification Wiring Typical Applications pipe systems cooling and/or heating pipe systems cooling and heating pipe systems cooling or heating with reheat Remote Sensor Accessories Home Screen Display How to Enter Setup Screen Appendix Support Version
2 INSTALLATION Location Do not install on outside wall. Do not install in areas with direct heat source. Do no install near any air discharge grill. Do not install in areas exposed to direct sunlight. Ensure Controller has sufficient air circulation. Ensure wall surface is flat and clean. Installation 1. Remove security screw (if any) on bottom of Room Controller cover.. unit by pulling on bottom side of Room Controller (Figure 1).. Read FCC ID and IC label installed in cover before installing any wireless product.. Ensure correct side of base faces up.. Pull cables in (1cm) out from wall.. Align base and mark location of two mounting holes on wall.. Install anchors in wall (Figure ).. Insert cable in central hole of base.. Insert screws in mounting holes on each side of base.. Strip each wire 1/in ( 0.cm) from end.. Insert each wire and screw according to wiring chart.. Gently push excess wiring back into hole. 1. Gently align cover to top of base and snap in place from bottom (Figure ). 1. Install security screw. Figure-1 the cover Figure- Install the base If replacing an existing Room Controller, label wires before removal of Controller. Electronic controls are static sensitive devices. Discharge yourself correctly before manipulating and installing Room Controller. A short circuit or wrong wiring may permanently damage Room Controller or equipment. All SE00 series controls are designed for use as operating controls only and are not safety devices. Tampering with the devices or unintended application of the devices will result in a void of warranty. This device must be installed to provide a separation distance of at least in (0cm) from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Figure- Reinstall cover
3 CLEANING SE00 ROOM CONTROLLER Use a soft, pre-moistened lint-free cloth for cleaning. Avoid getting moisture in openings. Do not spray anything directly on SE000 Room Controller or use compressed air. Do not use caustic/corrosive products, ammonia, solvents or any cleaning product containing alcohol or grit. Never use tools directly on the touchscreen. Never use paint on SE000 Room Controller. Do not drop or crush SE000 Room Controller, or allow SE000 Room Controller to come into contact with liquids. Do not use a damaged device (such as one with a cracked screen). Functionality guarantees are no longer valid if the glass on the screen is broken. Failure to comply with these recommendations will result in damage to the unit and void the manufacturer s warranty.
4 TERMINAL IDENTIFICATION AND FUNCTION Terminal identification SExxU Description / Application Used in applications & Pipe & Pipe & Pipe Control Type = On/Off Control Type = Floating Control Type = Analog Internal Temperature X X X Internal Humidity Model Dependent Model Dependent Model Dependent 1- BO1 Not used Not used Not used - BO Fan-L Fan-L Fan-L - BO Fan-M Fan-M Fan-M - BO Fan-H Fan-H Fan-H - RC / V~ Hot V~ Hot V~ Hot V~ Hot - C / V~ V~ V~ V~ - Aux Heat Aux Heat Aux Heat - BO Aux Heat Aux Heat Aux Heat - Normally Cool Cool Not used - Normally Heat Heat Not used - Normally Cool Cool Analog Heat valve - Normally Heat Heat Analog Cool 1- RS + BACnet MS-TP + BACnet MS-TP + BACnet MS-TP + 1- RS - BACnet MS-TP - BACnet MS-TP - BACnet MS-TP - 1- RS Ref BACnet MS-TP Ref BACnet MS-TP Ref BACnet MS-TP Ref 1- UI1 UI1 Function UI1 Function UI1 Function 1- UI1 UI1 Function UI1 Function UI1 Function 1 Scom mon mon mon 1- UI1 UI1 Function UI1 Function UI1 Function 0- UI0 Remote Room Sensor Remote Room Sensor Remote Room Sensor 1 Scom mon mon mon - UI Remote Supply Sensor Remote Supply Sensor Remote Supply Sensor - UI Not used Not used Not used - UI Not used Not used Not used
5 Wiring Power & Fan ( All models ) Speed Speed Single speed Transformer RC ( ) C (mon) BO Auxiliary output wiring Dry contact to end device maximum power to relay RC ( ) RC ( ) C (mon) C (mon) R R Main outputs wiring Pipe Applications Pipe Applications Pipe Applications Pipe Applications Pipe Applications Control type = On-Off Heating / Cooling valve OR NC NO UO 0 NC NO OR OR Heating valve Cooling valve Floating control Heating / Cooling valve Heating valve Cooling valve Analog control Heating / Cooling valve Heating valve Cooling valve Schneider Electric II-S00-A.EN.0.01.v April 01
6 TYPICAL APPLICATIONS Schematic Wiring Settings Normally d On/Off pipe system cooling and/or heating Control type = On / Off RC ( ) fan relays Pipe no = pipes CntrltTyp = On/Off Fan Menu = 0 (L-M-H) FL time = N/A Sensor Cooling / Heating 1 1 C (mon) NC mon UI 1 Optional supply water temperature sensor Transformer Normally d pipe system cooling and/or heating Control type = Floating If cooling only set: SeqOpera = Cooling only If heating only set: SeqOpera = Heating only If heat / cool auto-changeover with a local water temperature sensor set: SeqOpera = Cooling only UI1 = COS
7 Schematic Wiring Settings Pipe no = pipes CntrltTyp = Floating Fan Menu = (L-M-H) FL time = as per actuator fan relays RC ( ) C (mon) Modulating Floating Cooling / Heating Sensor 1 mon 1 UI1 Transformer If cooling only set: SeqOpera = Cooling only If heating only set: SeqOpera = Heating only Normally d If heat / cool auto-changeover with a local water temperature sensor set: SeqOpera = Cooling only UI1 = COS Optional supply water temperature sensor pipe system cooling and/or heating Control type = Analog Pipe no = pipes CntrltTyp = Analog Fan Menu = (L-M-H) RA/DA = as per actuator fan relays Modulating Analog Cooling / Heating Sensor RC ( ) C (mon) Transformer If cooling only set: SeqOpera = Cooling only If heating only set: SeqOpera = Heating only 0 to 1 mon 1 UI 1 Normally d Optional supply water temperature sensor If heat / cool auto-changeover with a local water temperature sensor set: SeqOpera = Cooling only UI1 = COS pipe system cooling and heating Control type = On / Off Normally d On/Off Cooling Heating fan relays RC ( ) C (mon) NC NC Transformer Heating Schneider Electric II-S00-A.EN.0.01.v Pipe no = pipes CntrltTyp = On/Off Fan Menu = (L-M-H) SeqOpera = Cool/Heat Cooling Normally d April 01
8 Schematic Wiring Settings pipe system cooling and heating Control type = Floating Modulating Floating Cooling Heating fan relays RC ( ) C (mon) Transformer Heating Pipe no = pipes CntrltTyp = Floating Fan Menu = (L-M-H) FL time = as per actuator SeqOpera = Cool/Heat Cooling pipe system cooling and heating Control type = Analog Modulating Analog Cooling Heating fan relays RC ( ) C (mon) Transformer 0 to 0 to Heating Cooling Pipe no = pipes CntrltTyp = Analog Fan Menu = (L-M-H) RA/DA = as per actuator SeqOpera = Cool/Heat pipe system cooling or heating with reheat Control type = Floating fan relays Modulating Floationg Cooling / Heating Electric Reheat Sensor Schneider Electric II-S00-A.EN.0.01.v RC ( ) C (mon) 1 S 1 UI 1 Transformer Electric Reheat Normally d Pipe no = pipes CntrltTyp = Floating Fan Menu = (L-M-H) FL time = as per actuator SeqOpera = Cool/Reheat UI1 = COS Optional supply water temperature sensor April 01
9 REMOTE SENSOR ACCESSORIES Model no. S0W00 S00W00 Description Wall mounted temperature sensor Wall mounted temperature sensor with override button and occupancy status LED The SE00 Room Controller is compatible with remote mount temperature sensors using K type NTC thermistors. Note: If one or multiple sensor(s) is/are connected into the RS terminal, the internal temperature sensor is automatically disabled. Disconnecting the sensor(s) in the RS terminal will re-activate the internal sensor. Features: Each sensor can be configured for various averaging combinations (refer to S000 series remote sensors for more details) Optional occupancy led Optional override key Wiring example of single remote room sensor: SE00 Series Controller S00W Remote wiring 1 sensor S-1= On, S-=On S0W Remote wiring 1 sensor S-1= On, S-=On mon UI 0 S RS OR S RS BO UI1 Aux C DI Dip switch setting for: 1 sensor ON 1 S-1 = ON S- = ON Temperature vs. resistance chart for Kohm NTC thermistor (R C = KΩ±%, B/ C = K±1.%) ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm
10 HOME SCREEN DISPLAY Hospitality User Interface Shown Date Short Network Message Occupancy Status Time System Status Fan Status Room Indoor Temperature Room Indoor Humidity Outdoor Temperature Up Arrow Raise Temperature Setpoint Actual Setpoint Down Arrow Lower Temperature Setpoint System Mode Select system mode Fan Mode Select fan mode Temperature Units Select Celsius or Fahrenheit Language Select preferred language Help Enter help screen Note: User HMI is configurable and allows display functions such as Date, Time, Humidity, Outdoor Temperature, Setpoint, and others to be enabled or disabled by setting various parameters.
11 HOW TO ENTER SET-UP SCREEN Touch and hold this point for seconds to enter set-up mode Note: If a configuration/installer password is activated to prevent unauthorised access to the configuration menu parameters, a password entry prompt shows to prevent access to device configuration components. For more information on using and configuring the functions of the HMI, refer to the following document: SE00 User Interface Guide SET-UP SCREEN DISPLAY 1/ Setup Network Configuration Setpoints - Display Service view Test outputs Language selection Enter BACnet & ZigBee network settings Enter parameter configuration menu Enter setpoint & display settings Enter status and service view Enter output testing mode Enter language selection General Note: Return to home screen Discover Mode The Controller becomes discoverable on the wireless ZigBee network for 1 minute (this button is hidden if ZigBee settings are not configured) Adjustable parameter Non-adjustable parameter
12 APPENDIX A TERMINAL CORRESPONDENCE The terminals of a SE00 are identified differently and have a wider range of possible functions compared to those of any of the SE000 series Room Controllers. Nonetheless, there is a direct correspondence of functions between the terminals of the SE000 series and the SE00 series. Consult the table below to verify the appropriate terminal when replacing a SE000 Room Controller with a SE00 Room Controller. SE000 SE00 Terminal name Terminal ID Terminal name Terminal ID Binary Input 1 BI1 Universal Input 1 UI1 Binary Input BI Universal Input 1 UI1 Universal Input UI Universal Input 1 UI1 Sensor mon Scom Terminal 1 mon COM Remote Sensor RS Universal Input 0 UI0 - RS Sensor mon Scom Terminal 1 mon COM Mix/Supply Sensor MS Universal Input UI - SS APPENDIX B POWER OUTAGE CLOCK RESET In the event of a power outage, SE00 Room Controllers retain the correct time as long as the duration of the power outage is not prolonged. Depending on the duration of the power outage, the Room Controllers internal clock may need to be updated or reset completely. The following table gives an indication of the expected clock performance after a power outage of a given duration. Outage duration Room Controller behavior 0 - hours Clock functions are normal - hours Clock accuracy not guaranteed, time may need to be adjusted - hours Clock no longer increments and will need to be adjusted when power is restored. + hours Clock functions are fully reset, and will need to be reinitialized as per a new installation.
13 1 Technical Support For any issues with SmartStruxure Solution or SmartStruxure Lite, contact Schneider Electric Technical Support according to your region. North America (NAM) Product Support Building Management Systems Field Devices Global Product Support Building Management Systems Field Devices Schneider Electric is the global specialist in energy management and automation. With revenues of ~ billion in FY01, our 10,000+ employees serve customers in over 0 countries, helping them to manage their energy and process in ways that are safe, reliable, efficient and sustainable. From the simplest of switches to complex operational systems, our technology, software and services improve the way our customers manage and automate their operations. Our connected technologies reshape industries, transform cities and enrich lives. At Schneider Electric, we call this Life Is On.
SE8300 Series Installation Guide 24 Vac Low Voltage
Installation Guide 24 Vac Voltage mercial and Hotel/Lodging HVAC Fan Coil Applications CONTENTS Installation 2 Configurable BI/UI Universal Inputs Overview 3 Setup Screen Display 3 Terminal Identification
More informationSE7200 Series Installation Guide
SE7200 Series Installation Guide 24 VAC Low Voltage Zoning Terminal Equipment Controller For Commercial HVAC Applications CONTENTS Installation 2 Preparation 2 Location 2 Installation 2 Configurable BI/UI
More informationPIR Ready VT7200 Series 24 Vac Low Voltage Zoning Thermostats For Commercial HVAC Applications (Issue Date June 12, _R2)
Product overview PIR Ready VT7200 Series Low Voltage Zoning Thermostats For mercial HVAC Applications (Issue Date June 12, 2008 028-0190_R2) The VT7200 PI thermostat family is specifically designed for
More informationModbus Integration Integration for Modbus Functionality for VT8600 Series
Modbus Integration Integration for Modbus Functionality for VT8600 Series Building Management System *For data visualization and analysis Modbus Controller VT8000 Series room controllers 2 TABLE OF CONTENTS
More informationSC3000 Series Line Voltage Switching Relay Pack Controllers Installation Guide
SC3000 Series Line Voltage Switching Controllers Installation Guide Commercial and Hotel/Lodging HVAC Fan Coil Applications CONTENTS Disclaimers 2 Installation 3 Communication Wiring to SERX3xxA 4 SC3xxx
More informationBAPI-Stat 3 Room Sensor
Overview and Identification The BAPI-Stat 3 is a multiple output transmitter for temperature and humidity with setpoint capability for both and occupied/unoccupied override switching. The large easy-to-read
More informationFan Coil Thermostat. Specification & Installation instructions TFC54F3X1. Technical Data
Fan Coil Thermostat Feature: Selectable analog & digital output Selectable fan speed contact Selectable Fahrenheit or Celsius scale Manual Night Set Back override (programmable) Multi level lockable access
More informationMetasys Zoning Package Installation
Technical Bulletin Issue Date August 28, 2002 Metasys Zoning Package Installation Metasys Zoning Package Installation...2 Introduction... 2 Key Concepts... 3 Installation Overview... 3 Metasys Zoning Package
More informationTC62D Installation Instructions
TC62D Installation Instructions January 2007 This TC62D has a return water low temperature limit option. Using the low limit precludes using a room sensor because both sensors plug into the same port.
More informationSMT-AZC INSTALLATION / OPERATION MANUAL
SMT-AZC INSTALLATION / OPERATION MANUAL 22o OFF VERSION 2.0 www.smarttemp.com INTRODUCTION The SMT-AZC thermostat is designed to work with the Smart Temp 24Volt Zone Dampers TERMINAL DESIGNATIONS The SMT-AZC
More informationBAPI-Stat Quantum Temperature Sensor with Display, Button Setpoint, Fan or System Mode Control
Product Identification and Overview The BAPI-Stat Quantum style room temperature sensor features a large format LCD and pushbutton setpoint adjustment. Additional options include pushbutton override, fan
More informationSE7000 Series Room Controllers
SE7000 Series Room Controllers Make the most of your energy SM Powerfully simple temperature control Efficient building control You can now take full control of your building s HVAC whether retrofitting
More informationCombined Ventilation Controller RVWS-T-224HA
Combined Ventilation Controller RVWS-T-224HA 8-stage Control for Power/Natural Applications 2 variable speed stages, 2 curtain winch stages, 2 fixed speed ventilation stages, 1 thermo/mister cycle stage
More informationschneider-electric.com/sg K60 Circuit Breakers The affordable way to stay safe from electrocution and electrical overloads schneider-electric.
K0 Circuit Breakers The affordable way to stay safe from electrocution and electrical overloads Overview K0 Circuit Breaker Technical Specification MCB RCCB K0 Circuit Breaker K0N K0H ID K Number of poles
More informationSignet Pressure Transmitter
Signet 80 Pressure 80.090 80.090 Rev. J 0/ English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents. Installation.
More informationBAPI-Stat Quantum Temperature Sensor with Display and Slider Setpoint
Product Identification and Overview The BAPI-Stat Quantum style room temperature sensor features a large format LCD and slider setpoint adjustment. Additional options include button override and communication
More informationInlet Controller TC5-ITA USER'S MANUAL. M rev. 02 K rev. 00
Inlet Controller TC5-ITA USER'S MANUAL M 890-00047 rev. 02 K 895-00458 rev. 00 TABLE OF CONTENTS PRECAUTIONS... 3 FEATURES... 4 LOCATION OF THE CONTROLS... 5 Status Leds...5 Internal Switches...6 INSTALLATION
More informationSignet Temperature Transmitter
Signet 80 Temperature English 80.090 80.090 Rev. G /0 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents.
More informationFactory Packaged Controls. OE (AAON Part No. V12090) MODGAS-X Controller Field Technical Guide
Factory Packaged Controls OE377-26-00058 (AAON Part No. V12090) MODGAS-X Controller Table of Contents GENERAL INFORMATION... 3 Overview...3 Features...3 INSTALLATION & WIRING... 4 Supply Air Temperature
More information32XR. 3 Phase Duplex Pump Control Panel (Level Transmitter Based) Quick Start Guide
32XR 3 Phase Duplex Pump Control Panel (Level Transmitter Based) Quick Start Guide RED ALARM LIGHT LEVEL CONTROLLER H-O-A SWITCHES HORN SILENCE INNER DOOR MOTOR STARTERS WITH INTERCHANGEABLE OVERLOAD MODULES
More informationThe PowerLogic wireless range is designed to retrofit existing switchboards, and enhance energy efficiency of buildings in operation for many years.
em4300 series The PowerLogic wireless range is designed to retrofit existing switchboards, and enhance energy efficiency of buildings in operation for many years. It achieves this by monitoring energy
More informationRemote Temperature Controllers. Quick Selection Guide
Remote Temperature Controllers Quick Selection Guide A Complete Selection For A Wide Range Of Applications Electronic Standalone Controllers T775 Provide on/off, modulating, or reset control in applications
More informationZoneTouch V2 Zone Control System Installation Manual
ZoneTouch V2 Zone Control System Installation Manual www.polyaire.com.au 2014 Polyaire Pty Ltd TABLE OF CONTENTS 1) Application 2 2) Features 2 3) Components 3 4) Configuration 4 5) Pre-Installation 6
More informationPerfectTilt RF Motorized Shutter User Manual
PerfectTilt RF Motorized Shutter User Manual Pictured: PerfectTilt RF Solar with auxiliary solar panels and auxiliary battery pack INTRODUCTION The PerfectTilt RF motorization system features a remote
More informationBurden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM
Contents Section Page 1.0 Introduction 1 2.0 Specification 1-4 3.0 Installation 5-8 4.0 Programming 9-10 5.0 Menus 10-12 6.0 Fault Finding/Diagnostics 12-13 7.0 Communication 13 8.0 Setting Up 13-16 1.0
More informationEngineering Bulletin. IntelliPak RTM (Rooftop Module, 1U48) Subject: Generic Building Automation System (GBAS, UCM Module, 1U51)
Engineering Bulletin IntelliPak RTM (Rooftop Module, 1U48) Subject: Generic Building Automation System (GBAS, UCM Module, 1U51) Issued By: Clarksville Marketing and Sales Support Order No. UN-PRB001-EN
More informationELECTRONIC THERMOSTAT: T901
μnistδt ELECTONIC THEMOSTAT: T One contact output DESCIPTION The T series proportional thermostats are microcomputer based, proportional and integral (PI) devices with one contact time proportioning output.
More informationCO 2 Room Sensor in the BAPI-Stat 3 Enclosure with Common Ground Configuration
Identification and Overview The BAPI CO 2 Sensor is an accurate and reliable way of incorporating demand controlled ventilation into a building s HVAC strategy. It measures the CO 2 in a range of 0 to
More informationBAPI-Stat 4 Room Humidity Sensor (BA/ B4 -H200 Series)
Overview The BAPI-Stat 4 Style room unit is available as a humidity only sensor or as a combination temperature and humidity sensor with optional LCD display, temperature setpoint adjustment and occupant
More informationHardware Installation. Tracer AH541 Version 2 Air-Handler Controller CNT-SVN02B-EN
Hardware Installation Tracer AH541 Version 2 Air-Handler Controller CNT-SVN02B-EN Hardware Installation Tracer AH541 Version 2 Air-Handler Controller CNT-SVN02B-EN February 2004 CNT-SVN02B-EN Tracer AH541
More informationSLIMZONE CLASSIC /
SLIMZONE CLASSIC 2701-001 / 2701-006 ZONE CONTROL SYSTEM INSTALLATION AND OPERATION MANUAL TABLE OF CONTENTS 1. INTRODUCTION...1 1.1 IMPORTANT NOTE...1 1.2 FEATURES...1 1.3 SAFETY INSTRUCTIONS...1 2. APPLICATION
More informationZIP Economizer Fault Detection and Diagnostics (FDD) Table
Fault Detection and Diagnostics (FDD) Table Fault Detection Problem Diagnostic ction (in addition to alarm stored / transmitted) Potential Cause C Fault Code OT sensor predetermined range O damper returns
More informationSignet Pressure Transmitter
Signet 8450 Pressure English 8450.090 8450.090 Rev. G /06 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents
More informationThermometer models / 00831A
Instruction Manual Thermometer models 00822 / 00831A CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries...
More informationInduction Power Supplies
Induction Power Supplies 7.5kW; 135 400kHz 480V version (Integral Heat Station) User s Guide Model 7.5-135/400-3-480 SMD Control Brds Rev. D 5/08 Table of Contents 1. Specifications and features...3 2.
More informationECL Apex 10. User Guide. ECL Apex 10 *087R9745* Installation and configuration. *vijem102*
User Guide ECL Apex 10 *087R9745* *vijem102* Installation and configuration VI.JE.M1.02 Danfoss 11/2004 DH-SMT VI.JE.M1.02 Danfoss 11/2004 DH-SMT ECL Apex 10 VI.JE.M1.02 Danfoss 11/2004 DH-SMT VI.JE.M1.02
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.
Technical Information Electric Slide-In Range JES9750AAB/S/W JES9800AAB/Q/S/W JES9860AAB/S/W Due to possibility of personal injury or property damage, always contact an authorized technician for servicing
More informationSB 2000 PUSH TO SEARCH NEXT STAG E. Aerotech, Inc. FORM: QM 1320
Inlet Controller SB 2000 USER'S MANUAL AUTO OPEN MANUAL PUSH TO SEARCH NEXT STAG E CLOSE Aerotech, Inc. FORM: QM 1320 4215 Legion Dr. Mason, MI 48854-1036 USA Rev. 3, Sept. 1997 Ph. (517) 676-7070 Fax
More informationMicroTech II Applied Rooftop Unit Controller
Installation and Maintenance IM-696-2 Group: Applied Systems Part Number: IM696 Date: March 2004 MicroTech II Applied Rooftop Unit Controller Used with McQuay models: RPS, RFS, RCS, RDT, RPR, RFR, RPE,
More informationQUICK START GUIDE VAV CONTROLLERS & WALL SENSORS rue Charles, Suite 100, Mirabel, QC, J7J 1X9
QUICK START GUIDE VAV CONTROLLERS & WALL SENSORS www.proloncontrols.com info@proloncontrols.com 17 510 rue Charles, Suite 100, Mirabel, QC, J7J 1X9 REV 1.0 PL-QCK-WSENSOR/VC2000-EN Copyright 2018 Prolon.
More informationSetPoint 501 and 501s Controllers Installation and Operation Manual
SetPoint 501 and 501s Controllers and Operation Manual SetPoint 501s SetPoint 501 Setpoint 501 and 501s Controllers and Operation Manual is published by Uponor Wirsbo, Inc. 5925 148th Street West Apple
More informationAir Conditioner. Installation manual. Wired remote controller MWR-WE11N
Air Conditioner Installation manual Wired remote controller MWR-WE11N Thank you for purchasing this Samsung Product. Before operating this unit, please read this installation manual carefully and retain
More informationRC-DO. Room controllers with display and manual forced ventilation function
revision 10 2017 RC-DO Room controllers with display and manual forced ventilation function RC-DO is a room controller from the Regio Mini series intended to control heating and cooling in a single zone.
More informationApplication Guide Paragon TM Control Module (PCM) Slide Valve and Protection Control 10/25/2016 Rev 1. Carlyle Controller Part No.
Application Guide 575-012 Paragon TM Control Module (PCM) Slide Valve and Protection Control 10/25/2016 Rev 1 Carlyle Controller Part No. 2BSB000928 1 General Description The PCM is part of Paragon Compressor
More informationDescription. functions including single duct pressure dependent or pressure independent systems.
Description The Meridian Basic control system converts a single zone HVAC unit into a variable air volume/variable air temperature multiple zone system. The microprocessor based Zone Manager calculates
More informationOperations Manual OM
Operations Manual OM 1063-2 Daikin BACnet VAV Controller Model 2508024 Group: Applied Air Systems Part Number: OM 1063 Date: January 2017 Supercedes: OM 1063 Owner s Manual Table of Contents Introduction....
More informationCooling mode. Temperature adjustment button. Override button. 24 VAC COM AN1 COM OPEN CLOSED T2/AN2 T2/COM T3 T3 COM SENSOR COM C-Over COM NSB
TB6980/TB7980 1. Introduction The TB6980/TB7980 digital thermostats provide proportional plus integral individual space temperature control in zoned commercial HVAC systems such as hydronic and pressure
More informationWIRELESS WALL ADJUSTER INSTALLATION, OPERATION AND MAINTENANCE
FORM 040.202 REV 106 WIRELESS WALL ADJUSTER INSTALLATION, OPERATION AND MAINTENANCE Models: ADJ-W Wireless Wall Adjuster Compatible with all Type HC, CW and C Therma-Fuser Diffusers CONTENTS ORDERING...
More informationBACnet MS/TP Networking Flow Balancing Control Valves
VFB30 Series Revision Date May 8, 2013 BACnet MS/TP Networking Flow Balancing Control Valves Establishes a flow coefficient (Cv) similar to globe valves, eliminating the need for pipe size correction tables
More informationVARIABLE SPEED USER MANUAL. Premium Efficiency Variable Speed Motor
VARIABLE SPEED USER MANUAL Premium Efficiency Variable Speed Motor SAFETY Safety is emphasized throughout the user manual. These are safety alert symbols. They alert the user to potential personal injury
More informationBAPI-Com, Two Wire Multifunction Sensor with Setpoint Slider (BA/BS4SCOM) Temperature/Humidity Sensor
Product Identification and Overview Power and Communication on Just Two Wires Available with Temperature Sensing, Temperature Setpoint, Optional Occupant Override, Optional Display and Optional %RH Sensing
More informationDigital Room Thermostats with Touch Screen LCD
TC40 Touch Series Digital Room Thermostats with Touch Screen LCD Revision Date February 22, 2013 Features Wall-mount Display Control to match any decor Extra large easy-to-read Liquid Crystal Display (LCD),
More informationAPPLICATION GUIDE. Simplicity LINC GATEWAY OVERVIEW. 24 must be grounded close to the Simplicity LINC
APPLICATION GUIDE Simplicity LINC GATEWAY OVERVIEW The Simplicity LINC Gateway operates as a Modbus Client providing an interface between a MS/TP control system and devices that communicate using the Modbus
More informationWireless Remote System RC-12v & 24v Standard RF Remote Control System INSTALLATION MANUAL AND OWNERS GUIDE Table of Contents:
Wireless Remote System RC-12v & 24v Standard RF Remote Control System INSTALLATION MANUAL AND OWNERS GUIDE Table of Contents: Page: 1 Important Safety Instructions/Overview. Pages: 2 Quick Reference Specifications.
More informationCO 2 Room Sensor in the BAPI-Stat Quantum Prime Style Enclosure
Identification and Overview The BAPI CO 2 Sensor is an accurate and reliable way of incorporating demand controlled ventilation into a building s HVAC strategy. It measures the CO 2 in a range of 0 to
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.
Technical Information Gas Slide-In Range JGS8750ADB/S/W JGS8850ADB/Q/S/W Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this
More informationSMT-150 Installer Manual
SMT-150 Installer Manual 3 Stage Digital HVAC Controller Version 1.0 Version History January 2019 Version 1 - Original Document Thank you for your purchase of this premier product. Please take the time
More informationMicroTech Applied Rooftop Unit Controller
Installation & Maintenance Manual IM 483-6 Group: Applied Systems Part Number: 571477Y-02 Date: December 1996 MicroTech Applied Rooftop Unit Controller Used with McQuay models: RPS, RFS, RCS, RDT, RDS
More informationINSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
More informationACCUVALVE MODEL AVC6000 SUBMITTAL MATERIALS MODEL CODE. AccuValve Model AVC6000 AVC6 - - DWG. NO: REVISION: REV. DATE:
ACCUVALVE MODEL AVC6000 SUBMITTAL MODEL CODE WARNING: NOT FOR USE WITH PERCHLORIC ACID MATERIALS VALVE HOUSING MATERIAL 2 = 304SS, 20 GAUGE 3 = 316SS, 20 GAUGE 4 = ALUMINUM, 16 GAUGE 6 = HIGH TEMP 304SS,
More informationM u l t i P o w e r. CM MultiPower. Installation and Operating Manual
M u l t i P o w e r CM MultiPower Installation and Operating Manual Index 1. Introduction of the 4HS submersible pumps range... 3 2. Safety Instructions... 4 3. CM MP installation... 5 3.1 Electric wiring...
More informationStorEdge Wiring Guide & On Site Checklist - Europe, Australia & South Africa
StorEdge Wiring Guide & On Site Checklist - Europe, Australia & South Africa This document contains a battery wiring guide and on site checklist with steps for post-installation verification of a StorEdge
More informationInstallation and Operation Manual Back-UPS BX800CI-ZA/BX1100CI-ZA
Installation and Operation Manual Back-UPS BX800CI-ZA/BX1100CI-ZA Inventory Safety and General Information bu001c This unit is intended for indoor use only. Do not operate this unit in direct sunlight,
More informationGENERAL INFORMATION MECHANICAL INSTALLATION PRESSURE INDEPENDENT VALVES 2-1/2"-10" MVP INSTALLATION & OPERATION INSTRUCTIONS UNION CONNECTIONS
GENERAL INFORMATION INSTALLATION & OPERATION INSTRUCTIONS 1. Clean the lines upstream of valve particles larger than 1/16" diameter (welding slag, pipe scale and other contaminants). Griswold Controls
More informationWireless Thermometer model 00380
Instruction Manual Wireless Thermometer model 00380 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries...
More informationA419ABG-3C Electronic Temperature Control
Installation Instructions Issue Date June 16, 2003 A419ABG-3C Electronic Temperature Control Application IMPORTANT: Use this A419ABG-3C Electronic Temperature Control only as an operating control. Where
More informationInstruction Manual. Digital Panel Meter Model 3126 CAUTION. Code Type of T/C Measuring Range Display Range Accuracy
Instruction Manual Digital Panel Meter Model 3126 I-01861 1. Preface Thank you for purchasing our digital panel meter 3126 series. Before use, read this manual carefully and thoroughly, and keep this manual
More informationWe reserve the right to alter data according to improvements made. Previous documents become invalid with the issue of this document.
General information Actuator controls AC 01.2 for controlling multi-turn actuators of the SA/SAR type range and part-turn actuators of the SQ/SQR.2 type range. Features and functions Power supply Standard
More informationSERIES 700 ANALOG ELECTRONIC CONTROLS
SERIES 700 ANALOG ELECTRONIC CONTROLS with ACT24 Actuator Supplement INSTALLATION & OPERATION MANUAL Stock ID: IOM-700 October, 2000 2000 Environmental Technologies, Inc. Largo, FL 1.0 DEFINITIONS AND
More informationPowerView PV380-R2 Mechanical Configuration
PowerView PV380-R2 Mechanical Configuration Operations Manual *Products covered in this document comply with European Council electromagnetic compatibility directive 2004/108/EC and electrical safety directive
More informationStart-Up, Operation and Service Instructions
Article I. Krueger Proportional LineaHeat W/ Discharge Temperature Start-Up, Operation and Service Instructions SAFETY NOTE Air-handling equipment will provide safe and reliable service when operated within
More informationA419 Series Electronic Temperature Controls with NEMA 1 or NEMA 4X Watertight Enclosures
Installation Instructions Issue Date April 8, 2008 A419 Series Electronic Temperature Controls with NEMA 1 or NEMA 4X Watertight Enclosures Application IMPORTANT: The A419 Series Electronic Temperature
More informationRDG160TU Commercial Thermostat
Document No. 129-588 RDG160TU Commercial Thermostat Selecting Location Install the thermostat about 4 feet (120 cm) above the floor on an inside wall. Ensure that there is free airflow around the thermostat.
More informationCENTRIFLOW METER and ELECTRONICS WIRING and INSTALLATION MANUAL REV 01/16 ORIGINAL LANGUAGE Copyright 2016 Eastern Instrument Laboratories, Inc. All Rights Reserved. TABLE OF CONTENTS SAFETY Safe Operation...
More informationMANUAL INSTALLATION. Tracking Controller. TC Series. v100 Issue Date: 02/25/ Price Industries Limited. All rights reserved. Firmware: 1.3.
MANUAL INSTALLATION Tracking Controller TC Series v100 Issue Date: 02/25/16 2016 Price Industries Limited. All rights reserved. Firmware: 1.3.0 TABLE OF CONTENTS Product Overview General...1 Tracking Controller
More informationRELAY BOX PRODUCT MANUAL IMPORTANT
RELAY BOX PRODUCT MANUAL IMPORTANT Installer: This manual is the property of the customer and must be retained with the product for maintenance and operational purposes. 1 TABLE OF CONTENTS Page INTRODUCTION
More informationBAPI-Com, Two Wire Multifunction Sensor BA/BS4SCOM Temperature/Humidity Sensor Installation and Operating Instructions
Product Identification Fig 1. BAPI-Com Communication Output Module Fig 2. BAPI-Com Room Sensor, BA/BS4SCOM Operations Overview The BAPI-Com sensor is designed to be used in retrofit applications on just
More informationVisionPRO 8000 Thermostats
VisionPRO 8000 Thermostats INSTALLER SETUP AND SYSTEM TEST POCKET GUIDE 62-0266 INSTALLER SETUP 1. Press SYSTEM. FAN ON AUTO Inside SYSTEM HEAT AM SCHED HOLD M24079 2. Press and hold these two blank buttons
More informationTS , -850 Series TS , -850 Series TS-57031, TS
TS-5711-770, -850 Series TS-57011-770, -850 Series TS-57031, TS-57031-850 Electronic Room Temperature Sensors General Instructions Application These sensors provide electronic sensing of room temperature
More informationUL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD
UL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD Safety Precautions Read this manual thoroughly before proceeding with installation, connections (wiring), or maintenance and inspection. Ensure you
More informationTROUBLESHOOTING TP. Index
TROUBLESHOOTING TP Index E1 POWER CUT DETECTED... 2 E2 LOCK ERROR... 3 E3 DRAINAGE FAILURE / WATER IN TUB... 6 E4 MAXIMUM WATER LEVEL REACHED... 6 E5 FAULT WATER INLET... 6 E6 HEATING FAULT... 6 E7 MAXIMUM
More informationThermometer model 00826
Instruction Manual Thermometer model 00826 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries... 4 Set
More informationECON-ZIP-DETF; ZIP PACK
71765-00001_A INSTUTION MANUAL EON-ZIP-DETF; ZIP PAK EON-ZIP-DETF; ZIP PAK Differential Enthalpy with DV apability and TF Spring eturn Actuator ontains: Application This kit offers all the components to
More informationSTRA-24 for chilled beams
STRA- Installation and commissioning manual STRA- for chilled beams STRA- is the room controller for the pressure independent (Pi) and constant air volume chilled beams. It is possible to set different
More informationWireless Thermometer model 00782W
Instruction Manual Wireless Thermometer model 00782W CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries...
More informationThermometer models 02023, 02028, 02029
Instruction Manual Thermometer models 02023, 02028, 02029 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Set the Time, Date & Units...
More informationApplication. Tek-Air Systems, Inc. 41 Eagle Road Danbury, CT (203) FAX: (203) SALES FAX: (203)
TEK-AIR TECHNICAL PRODUCT DATA SHEET FVC2600 SASH SENSING VAV FUME HOOD SYSTEM MODEL 2600: Variable volume control based on sash position utilizes microprocessor based electronics and linear air control
More informationIMC SOLAR EAGLE 2 DIFFERENTIAL TEMPERATURE CONTROLLERS
DIFFERENTIAL TEMPERATURE CONTROLLERS MAIN FEATURES - Microprocessor programed specifically for optimal performance of WARM AIR systems - Large easy-to-read 40 character (x0) backlit LCD display showing
More informationEZvav Digital Controls
EZvav Digital Controls www.nailor.com CONTENTS SECTION 1: About the controllers.... 4 Specifications... 5 Safety considerations... 7 SECTION 2: Installing the controllers... 7 Setting the rotation limits...
More informationHeating Cable. Description
ITLS Base Panel Heat Tracing Control Panel for Ordinary Areas 10 VGA Touch Screen HMI 40 Amps/Loop @ 100 600 VAC 6 Loops to 72 Loops NEMA 4 or NEMA 4X Enclosure SCR Control Optional Wireless Temperature
More informationSP-32 & SP-32D SP-33, SP-33D SP-34, SP-34D. Description. Specifications. Single Stage Temperature Control
SP-32, SP-32D SP-33, SP-33D SP-34, SP-34D Single Stage Temperature Control Description The SP-3x and SP-3xD series of controls are single stage, general purpose, temperature controls with wide application
More informationMicroTech II Applied Rooftop Unit Controller
( Installation and Maintenance IM-696 Group: Applied Systems Part Number: IM696 Date: April 21 MicroTech II Applied Rooftop Unit Controller Used with McQuay models: RPS, RFS, RCS, RDT, RPR, RFR, RDS, RAR
More informationT500 Series. Applications. Features. Applicable Literature. Non-Digital, On/Off Thermostat General Instructions
T500 Series Non-Digital, On/Off Thermostat General Instructions Applications The T500 series thermostats are available in four basic models for low and line voltage control of valves, relays, and fan motors
More informationFD6209B LIABILITY DISCLAIMER
VEHICLE CONFIGURATION SETTINGS CHART Use the chart below to navigate through the different settings the Setup touch button has to offer. Also use the chart to see the different configuration settings offered
More informationSP PRO KACO Managed AC Coupling
SP PRO KACO Managed AC Coupling Introduction The SP PRO KACO Managed AC Coupling provides a method of linking the KACO Powador xx00 and Powador xx02 series grid tie inverters to the SP PRO via the AC Load
More information2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE
REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause
More informationAC drive has detected too high a Check loading
Fault code Fault Name Fault type Default Possible Cause Remedy 1 Over Current Fault AC drive has detected too high a Check loading current (>4*IH) in the motor cable: Check motor Sudden heavy load increase
More informationWelcome to ABB machinery drives training. This training module will introduce you to the ACS850-04, the ABB machinery drive module.
Welcome to ABB machinery drives training. This training module will introduce you to the ACS850-04, the ABB machinery drive module. 1 Upon the completion of this module, you will be able to describe the
More informationINSTALLATION AND OPERATION INSTRUCTION
INSTALLATION AND OPERATION INSTRUCTION ATi Max 2-1/2-6, 65-150mm Install the ATi Max valve either in the supply or return pipework for the unit. It is recommended that a strainer be installed prior to
More informationThermometer models 02023/02028/02053/02054
Instruction Manual Thermometer models 02023/02028/02053/02054 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Set the Time & Units...
More information