BORDEREAU DE TRANSMISSION DESSINS D'ATELIER & FICHES TECHNIQUES. Vitrerie LC Inc. Courriel , #202

Transcription

1 BORDEREAU DE TRANSMISSION DESSINS D'ATELIER & FICHES TECHNIQUES PROJET : Centre de formation Duchesnay N/D : SOUS-TRAITANT / FOURNISSEUR : Spécialité : Vitrerie Contact : Alexandra Lemieux Vitrerie LC Inc. Courriel :alexandra@vitrerielc.com Tél. : , #202 IDENTIFICATION DU MATÉRIEL SOUMIS (X) RESOUMIS (X) Description : Fiche technique quincaillerie Dessin(s) d'atelier Fiche(s) technique(s) Échantillon(s) LEED Section de devis et article(s) : Fournisseur : Selon produit Nombres de feuille(s) : Fabricant : Selon produit Produit(s) soumis : Raison(s) de l'équivalence : Tels que plans et devis Équivalence Si les produits soumis sont différents des documents de soumission, remplir la section "raisons de l'équivalence" et en démontrer l'équivalence. SIGNATURE DU SOUS-TRAITANT : MATÉRIEL SOUMIS À : Date : 16 janvier 2017 Architecte ing. civil Ing. structure Ing. mécanique Ing. électrique Laboratoire SUIVI DES DOCUMENTS Reçus sous-traitant Transmis professionnel Retour professionnel Retour sous-traitant Révision COMMENTAIRES DU PROFESSIONNEL VÉRIFICATION DU PROFESSIONNEL À l'essai : F-22-03

2 PRODUCT SPECIFICATIONS For more information visit XHD Extra Heavy Duty Concealed Leaf Hinge Application: - Lead lined model for hospital x-ray room doors with double row of screws to straddle lead (Specify "LL") - Frame and door leaf alignment ribs for proper hinge and door location PRODUCT SPECIFICATIONS CLEARANCE: - 15/32" (12 mm) hinge side plus standard lockside clearance FASTENERS: - 1/4"-20 Dril-Kwik screws or optional 1/-14 x 11/2" wood screws LENGTH OPTIONS: - Standard sizes include: - 83" (2108 mm) - 95" (2413 mm) - 119" (3023 mm) - Custom lengths available DOOR REINFORCEMENT: - None required to 200 lbs, use 16 gauge channel at higher weight FRAME REINFORCEMENT: - Frame reinforcement recommended for doors in excess of 200 lbs and 3 feet in width WARRANTY: - All Roton products have a lifetime warranty. When ordering electric Roton, the electric portion of the hinge has a one-year warranty. MATERIAL: - Aluminum 6063-T6 ELECTRIC MODIFICATIONS: - Power Transfer Preparation (EPT 2) or (EPT 10) - Electric Through-Wire (ETW) DOOR: - 1-3/4" to 2-1/4" thick

3 or K, RETW ROTON ELECTRICAL MODIFICATIONS or K, RETW For ease of ordering, Hager Companies has established standard locations for power transfer cutouts. All standard location dimensions are referenced from the top edge of the door to the centerline of the power transfer cutout. Please specify handing. NOTE: Full surface hinges are not available with preps. Opening Door Height Actual Hinge Length EMN ETM ETW EPT E1S E RETW 79 SD / / /2 41-1/ / /2 42-1/2 79 HD / / /2 40-7/ /4 24-3/ /2 42-1/2 41-7/8 83 SD / /2 43-7/8 42-3/4 28-7/ /2 46-1/2 83 HD / /2 45-1/ / /2 46-1/2 44-1/16 85 SD / /2 47-1/ / /2 48-1/2 85 HD / / / /4 30-7/ /2 48-1/2 45-1/16 95 SD /8 95-1/ /4 56-7/ /2 59-3/4 59-3/4 95 HD /8 95-1/ /4 56-7/ /2 59-3/4 59-3/4 56-1/2 119 SD / / / /8 83-3/4 83-3/4 119 HD / / / /8 83-3/4 83-3/4 80 SD = Standard Duty HD = Heavy Duty 139 Victor Street St. Louis, MO

4 ROTON ELECTRICAL MODIFICATIONS Von Duprin EPT 2 or EPT 10 Power Transfer Preparation Exposed Electric Contacts Exposed Electric Switches Concealed Electric Through-Wire Concealed Electric Monitoring Concealed Electric Through-Wire and Monitoring Part Number EPT E E1S ETW EMN ETM RETW HD HD HD HD HD HD LL HD LL HD LL HD LL HD LL HD Removable Electric Through-Wire 139 Victor Street St. Louis, MO

5 STANDARD LOCATIONS FOR ALL STAINLESS STEEL CONTINUOUS ELECTRICAL MODIFICATIONS Opening Door Height 79-1/8 83-1/8 85-1/8 95-1/ /8 Hinge Length 79-3/ /8 85-1/ /4 ETW 41-1/2 43-1/2 45-1/2 55-3/8 79-1/8 EPT 24-1/2 28-7/ / /2 64-7/16 E1S 41-1/2 43-1/2 45-1/2 55-3/8 79-1/8 139 Victor Street St. Louis, MO

6 Manual Flush Bolts Metal Doors Meets ANSI/BHMA A156.16, L UL Listed 3 Hour Fire Doors 8'0" x 10'0" FB457 Top or Bottom Bolts When the active door is opened, the lever can be moved to the up position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the down position, projecting the bolt into the strike and securely locking the inactive leaf. Simplified installation in metal frames. Round bolt head requires only a punched hole. Use of strike optional. Special design of guide and flat sided bolt tip to prevent bolt rotation. Non-handed. Bolt tip is 1/2" Diameter. Bolt throw is 3/4" with a 7/8" vertical adjustment. Bolt backset is 3/4" Standard Rod Length is 12", which is measured from the center of the flush bolt body to the bolt tip. Optional rod lengths available - 6", 9", 18" and 24" for fire rated doors. Optional rod lengths available - 6", 9", 18", 24", 30", 36" and 48" for non-fire rated doors. DP1 or DP2 optional dust proof strike available, see page C11. A Hinges & Pivots B Pulls & Plates C9 Flush Bolts & Coordinators Dimensions Body Size: 1-1/4" Wide x 6-3/4" Long x 1-1/8" Deep Guide Size: 1" Wide x 2" Long x 5/64" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick Finishes Ives Number US3 US4 US10 US10B US15 US26 US26D BHMA D Latches, Catches & Bolts E F Stops Exterior Hardware G Miscellaneous Hardware Ives Architectural hardware products C9

7 98/99 Rim exit device The 299 Strike ships standard, optional strikes available 98 and 99 Rim exit devices for all types of single and double doors with mullion, UL listed for panic exit hardware. Devices are ANSI A Grade 1. The 98 device has a smooth mechanism case and the 99 device has a grooved case. The rim device is non-handed except when the following device options are used: SD (special dogging), -2 (double cylinder) or SS (signal switch). See Opposite page for available outside trim and device functions. Covers stock hollow metal doors with 86 or 161 cutouts on single doors (may cover cutouts on pairs consult template). Hex key dogging comes standard on 98/99 Rim exit devices Finishes US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. 98/99 Rim exit device Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. Device lengths 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size Device centerline from finished floor Center case dimensions Mechanism case dimensions Projection Latch bolt Fasteners & sex bolts (SNB) /16" (1011 mm) /16" (1008 mm) with mullion 8" x 2 3 /4" x2 3 /8" (203mm x 70mm x 60mm) 2 1 /4" x 2 1 /4" (57mm x 57mm) Pushbar neutral 3 13 /16" (97 mm) Pushbar depressed 3 1 /16" (78 mm) Deadlocking, 3 /4" (19mm) throw Includes screw pack for 1 3 /4" (44mm) and 2 1 /4" (57mm) thick metal or wood doors. Optional 425 SNB available, see page 9 for quantities. Electric options LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric locking & unlocking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect Mechanical -2 Double cylinder options AX Accessible device GBK Glass bead kit PN Pneumatic latch retraction XP Extra protection SNB Sex bolts SEC Security screws Dogging feature Hex key dogging standard Dogging options CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Strikes 299 Dull black XP Extra protection 90 latch-tostrike contact Force resistance of 2,000+ lbs. QEL Quiet electric latch retraction Bolt retraction via switch Converts exit door to push-pull operation CX Chexit delayed exit Meets NFPA 101 requirements Self-contained controls, locking, alarm EL Electric latch retraction Enables remote unlatching Alternative to manual dogging PN Pneumatic latch retraction For areas where electrical devices banned Special linkage for mechanical or pneumatic dogging CD Cylinder dogging Replaces hex key dogging Requires 1 1 /4" mortise cylinder with inverted cam RX Pushpad monitor switch Signals use of an opening SPDT switch to monitor pushpad AX Accessible device UL certified to meet new 5 lb. maximum operating force requirement Exceeds ANSI/ BHMA requirements ALK Alarm exit kit Unauthorized opening triggers 85-decibel horn Set in armed or disarmed mode by key CON Allegion Connectors Common connectors to connect various door hardware all the way to the power supply 8 Von Duprin 98/99 Series

8 Standard trim EO DT NL NL-OP Product description Trim description Escutcheon plate size No outside trim Exit only 98EO 99EO Dummy trim Pull when dogged 98DT 99DT Night latch Key retracts latchbolt 98NL 99NL 990DT 990NL-R/V 3" x /16" x 3 /32" (76x360x2mm) 3" x /16" x 3 /32" (76x360x2mm) Pull center to center 5 1 /2" (140mm) 5 1 /2" (140mm) Projection 2" (51mm) 2" (51mm) ANSI function Cylinder type Rim Rim Handing Optional trim x990eo x996eo Optional #425 SNB quantity for device Product description x996k-dt x996l-dt x696dt x697dt x996k-nl x996l-nl x696nl x697nl Lever Key locks & unlocks 98L 99L Lever night latch Key retracts latchbolt 98L-NL 99L-NL Lever blank escutcheon Always operable (no cylinder) 98L-BE 99L-BE Night latch Key retracts latchbolt optional pull required 98NL-OP 99NL-OP 110NL-MD 110NL-WD Lever dummy trim pull when dogged 98L-DT 99L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size L L-NL L-BE L-DT 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) Pull center to center Projection 2 7 /8" (73mm) 2 7 /8" (73mm) 2 7 /8" (73mm) 2 7 /8" (73mm) ANSI function Cylinder type Rim Rim Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device * Electrified lever operation available 98/99 Rim exit device Notes Von Duprin 98/99 Series 9

9 9847/9947 Concealed vertical rod device Top Latch 338 Top Strike 9847/9947 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A Grade 1. The 9847 device has a smooth mechanism case and the 9947 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions. Finishes US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only. 385A Bottom Strike 9847/9947 Concealed vertical rod device Specifications Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. Device lengths 2' 2' (610 mm) Door size 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size Device centerline from finished floor 39 5 /8" (1006 mm) Standard Adjustable from 35 5 /8" (905mm) to 49 5 /8" (1260mm) Center case 8" x 2 3 /4" x2 3 /8" (203mm x 70mm x 60mm) dimensions Mechanism case 2 1 /4" x 2 1 /4" (57mm x 57mm) dimensions Projection Pushbar neutral 3 13 /16" (97 mm) Pushbar depressed 3 1 /16" (78 mm) Latch bolt Deadlocking top & bottom bolt, 5 /8" (16mm) throw Door undercut 1 /4" (7mm) recommended Top & bottom 4 1 /2" x 2 1 /8" x 1 1 /2" (114mm x 54mm x 38mm) Latch case Vertical rods Round 2-piece adjustable rods Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5 /8" (905 mm) to 49 5 /8" (1260 mm). Extension rod kits available for doors over 8'4" (2533mm). Fasteners & sex bolts (SNB) Includes screw pack for 1 3 /4" (44mm) to 2 1 /4" (57mm) thick metal doors. Optional 425 SNB available. Electric options LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect Mechanical GBK Glass bead kit options PN Pneumatic latch retraction LBR Less bottom rod PL Pullman latch SNB Sex bolts SEC Security screws Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Strikes Top Unfinished, Bottom 385A - Unfinished QEL Quiet electric latch retraction Bolt retraction via switch Converts exit door to push-pull operation CX Chexit delayed exit Meets NFPA 101 requirements Self-contained controls, locking, alarm EL Electric latch retraction Enables remote unlatching Alternative to manual dogging E (E996L) Electrified breakaway lever Electrified remote locking/unlocking Standard in fail safe condition PN Pneumatic latch retraction For areas where electrical devices banned Special linkage for mechanical or pneumatic dogging Bottom Latch Hex key dogging comes standard on 9847/9947 Concealed vertical rod devices RX Pushpad monitor switch Signals use of an opening SPDT switch to monitor pushpad CON Allegion Connectors Common connectors to connect various door hardware all the way to the power supply ALK Alarm exit kit Unauthorized opening triggers 85-decibel horn Set in armed or disarmed mode by key LX Latchbolt monitor switch Signals use of an opening SPDT switch to monitor latch bolt DI Dogging indicator Monitor dogging status without a control panel Red indicator light shows visibility to dogging from over 75 feet 28 Von Duprin 98/99 Series

10 Standard trim EO DT NL NL-OP TL TL-BE Product description No outside trim Exit only 9847EO 9947EO Dummy trim Pull when dogged (not recommended for fire device) 9847DT 9947DT Night latch Key retracts latchbolt 9847NL 9947NL Night latch Key retracts latchbolt optional pull required 9847NL-OP 9947NL-OP Thumbturn Key locks & unlocks (use with DT trim) 9847TL 9947TL Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9847TL-BE 9947TL-BE Trim description 990DT 990NL-R/V 110NL-MD 376T X 990DT 374T-BE X 990DT Escutcheon plate size 3" x /16" x 3 /32" (76x360x2mm) 3" x /16" x 3 /32" (76x360x2mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) Pull center to center 5 1 /2" (140mm) 5 1 /2" (140mm) Projection 2" (51mm) 2" (51mm) 2" (51mm) 2" (51mm) ANSI function or Cylinder type Rim Rim 1 1 /4" Mortise Handing Optional trim x990eo x996eo Optional #425 SNB quantity for device Product description x996k-dt x996l-dt x696dt x697dt x996k-nl x996l-nl x696nl x697nl Lever Key locks & unlocks 9847L 9947LF Lever night latch Key retracts latchbolt 9847L-NL 9947L-NL Lever blank escutcheon Always operable (no cylinder) 9847L-BE 9947L-BE Lever dummy trim pull when dogged 9847L-DT 9947L-DT Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT Escutcheon plate size L L-NL L-BE L-DT 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) 2 3 /4" x 10 3 /4" x 27 /32" (70x273x21mm) Pull center to center Projection 2 7 /8" (73mm) 2 7 /8" (73mm) 2 7 /8" (73mm) 2 7 /8" (73mm) ANSI function Cylinder type Rim Rim Handing Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible Optional #425 SNB quantity for device * Electrified lever operation available 9847/9947 Concealed vertical rod device Notes Von Duprin 98/99 Series 29

11 98/99 Strike information Strikes for rim devices F 499F 1408 Projection 9 /16" (14mm) Projection 13 /16" (21mm) Projection 13 /16" (21mm) Projection 15 /16" (24mm) One per pair of doors 1439 Blade stop 1410 Integral stop Projection 1 /2" (13mm) Projection 1 /2" (13mm) Projection 3 /8" (10mm) Panic devices only Requires coordinator For panic exit application only, not fire rated XP Strikes for rim devices Projection 13 /16" (21mm) Projection 7 /8" (22mm) - For fire rated double door applications Strikes for vertical rod devices 248L-4 260U-Flush transom panic only 260U-F-Flush transom fire only Strikes for vertical cable devices Top 249 strike Bottom strike 1" (25 mm) ⁹ ₁₆" (14 mm) 1¹ ₂" (38 mm) ¹ ₈" (3 mm) Projection 9 /16" (14mm) Projection 3 /8" (10mm) Projection 3 /8" (10mm) Projection 13 /16" (21mm) 1¹⁹ ₃₂" (40 mm) ¹ ₈" (3 mm) 2³ ₄" (70 mm) Projection 1 /8" (3mm) F 499F Projection 13 /16" (21mm) Projection 15 /16" (24mm) Strike options / Dogging options 304L A 283 Projection 13 /16" (21mm) Mortise 5 /8" (16mm) Mortise 2 1 /2" (64mm) For use with WDC devices when used with wood frames Strikes for mortise lock devices A 576B. Not for use with astragals For use on wood doors, contact door manufacturer Acceptable for 90 minute pair of hollow metal doors Von Duprin 98/99 Series 59

12 98/99 Electrical options RX Request to exit The RX (2xit) feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the pushpad. The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. The RX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resisitive maximum). The RX switch is available in a low current (LC) switch. Most commonly used in computer operated monitoring systems. To order, specify: Standard use prefix RX, example RX99EO Low Current use prefix RX-LC, example RX-LC98EO RX2 Double request to exit The RX2 feature uses two RX switches. To order, specify: Standard Use prefix RX2, example RX299EO WP-RX Waterproof request to exit LX Latchbolt monitoring The LX feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the latch bolt. The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. The LX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resistive maximum). SS Signal switch Monitors pushpad and latch bolt The SS feature is used to signal the unauthorized use of an opening. This device is equipped with two internal SPDT switches. One switch monitors both the pushpad and the latch bolt assembly, making the latch bolt tamper resistant, for positive security. An additional SPDT switch is connected to the 1 1 /4" (32mm) mortise cylinder with straight cam for alarm bypass. (Schlage cam reference B ). The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. Pushpad reads: Emergency Exit ONLY Push To Open And Sound Alarm. Pushpad is only available in US32D finish with red silk-screened lettering. The SS mortise lock device is furnished with both the signal switch device and the SS7500 mortise lock. The SS7500 mortise lock has the versatility and advantages of the 7500 lock with the addition of signalling functions to monitor latch bolt operation and the trim locking function. The SS7500 mortise lock is supplied standard with the SS mortise lock device. To order, specify: 1. Prefix SS, example SS99L. 2. Handing required, LHR or RHR. Electrical ratings: Up to VDC Popular SS application Unauthorized use of this opening will activate the local horn. The key switch permits inhibiting this system for authorized entry. Electrical options & accessories The LX switch is available in a low current (LC) switch. Most commonly used in computer operated monitoring systems. To order, specify: Standard Use prefix LX, example LX99EO Low Current Use prefix LX-LC, example LX-LC98EO Electrical rating for all switches: Standard 2 Amp 24VDC Low Current (LC) - below 50 24VDC Note: All switches can be either factory or field installed 61 Von Duprin 98/99 Series 61

13 Electrical options & accessories 98/99 Electrical options EL Electric latch retraction The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging. If manual hex-key dogging is required, specify HD-EL. If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-EL. SD-EL is not available on the 9875 or 9975 devices. EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system. UL approved for Class II circuit applications. The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply. The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information. Solenoid specifications: Continuous duty 24 VDC Current inrush 16 Amps Current holding 0.3 Amps Solenoid resistance: -grn-yel OHMS -grn-org OHMS To order, specify: Standard use prefix EL, example EL99L. Hex Key dogging Use prefix HD-EL, example HD-EL99L. Special center case dogging Use prefix SD-EL, example SD-EL99L Minimum door opening widths: Application Surf. vert. Con. vert. Mortise Rim Min. door opening 28 1/4" 28 1/4" 28 3/4" 29 1/4" 120/240 VAC SC I1 O1 I2 O2 GND Von Duprin exit device a* b* a* b* Popular EL application Power supply PS914-2RS Electric power transfer EPT-2 or EPT-10 EPT-2 EPT-2 EL #2 EL #1 EL Wire length (feet) 1 Input #2 (Required for independent operation only). Input # EL 98/99 Rim a * All other 98/99EL device types b * Control Switch Wire gauge (AWG) 1. Wire lengths include an EPT, Door loop, electric hinge or pivot and are measured one way between the PS914/option board and the device. 2. Table is applicable to devices that have shipped after August Von Duprin 98/99 Series QEL Quiet electric latch retraction The QEL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. Different than the popular EL, the QEL quiet operation is achieved using an electric drive motor which retracts the latch bolt either momentary unlatching or for extended periods of time. This feature is an alternative to manual dogging. If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-QEL. SD-QEL is not available on the 9875 or 9975 devices. QEL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system. UL approved for Class II circuit applications. The QEL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS902 or 914 power supply. The PS902/914 with the 2RS, 4RL or 4R board is the minimum required. Other option boards available for other functions, see PS902/914 power supply for additional information. The QEL has a low in rush current, so it can be used with standard Schlage power supplies. Calculate the peak current draw of all devices in the system to determine the required amperage of the supply. Schlage PS902 Schlage PS904 Schlage PS906 up to 2 amps up to 4 amps up to 6 amps QEL Electrical load Voltage 24VDC Current 1.0 A Inrush (0.5 sec.) / 0.14 A Holding The -2RS option board is designed to control two electric latch retraction devices and provide time delay between the firing of outputs is required. The power transfer is also sold separately. To order, specify: Standard use prefix QEL, example QEL99L. Special center case dogging use prefix SD-QEL, example SD-QEL99L 120/240 VAC SC I1 O1 I2 O2 GND a* b* a* Popular application Power supply PS902-2RS Electric power transfer EPT-2 or EPT-10 EPT-2 EPT-2 QEL #2 QEL #1 Input #2 (Required for independent operation only). Input #1 b* a * Distance (one-way) Wire gauge AWG AWG AWG AWG b * Wire selection Switch wire size 1200 ft. Max. 18 gauge standard

14 98/99 Electrical options EPT Electrical power transfer PNT Pneumatic transfer Electric Power Transfer provides a means of transferring electrical power from a door frame to the edge of a swinging door. The units are completely concealed when the door is in the closed position, and are ideal for installations involving abuse or heavy traffic. E Electric mortise lock device Electrical options & accessories Two models are available; EPT-2, two 18 gauge wires and EPT-10, ten 24 gauge wires. The EPT-2 and EPT-10 are U/L listed as miscellaneous door accessory. UL Listed for use on firedoors Degree of opening Hinge type Door thickness Up to 5" butt hinges 1 3/4" Up to 3/4" offest pivots 1 3/4" /2" butt hinges 1 3/4" " butt hinges 1 3/4" 0-90 Swing clear hinges 1 3/4" Finishes SP28 (sprayed aluminum) SP313 (sprayed duranodic). Dimensions Housing 9" x 1¹ ₄" x 1⁵ ₈" (229mm x 32mm x 38mm) EPT-2 Two 18 gauge wires, Up to 2 24VDC, with a 16 AMPS Maximum Surge EPT-10 Ten 24 gauge wires, Up to 1 24VDC, with a 16 AMPS Maximum Surge PNT-1 ⁵ ₃₂" Tubing To order, specify: 1. EPT-2,EPT-10 or PNT Finish, SP28 or SP313. E996L Electrified breakaway lever E996L Electrified lever trim provides remote locking and unlocking. Furnished standard in fail safe (FS) condition, can be field converted to fail secure (FSE) where allowed. E996L is furnished standard with cylinder operation for nightlatch (NL) function, or with blank escutcheon (BE). Specification: Solenoid continuous duty 24VDC Solenoid draw 0.22 amp. To order, specify: 1. Use E prefix, example E996L. When ordering with the exit device specify trim series with prefix E, example 9927L-BE 3' US26D E Device type, R/V (rim/surface vertical rod/concealed vertical rod) or M (mortise). 3. RHR furnished standard if not specified, field reversible. 4. Lever style (06 lever furnished standard). Other levers, no extra charge. The electric mortise lock device has all the versatility and advantages of the standard mortise lock device, plus the advantage of being electrically controlled by a remote switching device, an access control system or an automatic fire alarm system. The device features the E7500 mortise lock. The E7500 controls the locking of the outside trim. When unlocked, the door remains latched, preserving the fire rating of the door and making it particularly useful where codes permit locking but require unlocking during a fire emergency. The outside trim cylinder retracts the latch bolt for mechanical override, night latch function. Only available with TP, K or L functions. The E7500 lock contains a SPDT signal to monitor the outside trim condition (locked or unlocked) and a second SPDT signal switch to monitor the latch bolt. Standard features: Field reversible handing 24 VDC continuous duty solenoid Optional features: Fail safe (locked when energized, unlocked when deenergized or during power failure). Specify with suffix FS. Fail secure (unlocked when energized, locked when deenergized or during power failure). Specify with suffix FSE 24 VAC (with SO option) 12 VDC 12 VAC (with SO option) Note: Some Fire codes will require Fail Safe (FS) operation for stairwell doors.be sure to specify the correct operation for your application. Electrical specifications: Solenoid.60 12VDC.30 24VDC Each switch Up to VDC Maximum The E option does not include the power transfer from door to frame, the power supply or the control operator. (Refer to EPT-10 and PS902 or PS914 power supply) To order, specify: 1. Use prefix E, example E FS or FSE 3. Voltage and current. Electric mortise lock device Adaptable for openings where continuous latching is required while the trim may be electrically locked or unlocked from a remote location stairwells, exterior doors, etc. Minimum system requirements: PS902 EPT Von Duprin 98/99 Series

15

16

17 4040XP Series Features The 4040XP is LCN s most durable and flexible heavy duty closer designed for institutional and other demanding high traffic applications. Certifications Body Construction Fluid Handing Grade 1 - ANSI A156.4, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act n Cast Iron Body n Full Complement Bearings n 1-1/2 Diameter Piston n 3/4 Diameter Double Heat Treated Pinion Journal All Weather Liquid X Fluid Non-Handed Templating Peel-n-Stick templates - 2-1/4 x 5 Mounting Hole Pattern Size Warranty Adjustable Spring Size 1-6, includes Patented Green Dial 30 years Cover Fasteners Mounting Arms Finishes/Colors/ Powder Coat n Plastic, Standard n Metal, Optional Self Reaming and Tapping Screws (SRT) Hinge (Pull Side), Top Jamb (Push Side), Parallel Arm (Push Side) Regular Arm n Aluminum (689) n Statuary Bronze (690) n Light Bronze (691) n Black (693) n Dark Bronze (695) n Brass (696) n Custom colors optional n Optional SRI primer - powder coat only n Optional plated finishes Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. HINGE (PULL) SIDE TOP JAMB (PULL) TOP JAMB (PUSH) MOUNTING PARALLEL ARM STOP FACE POWDER COAT PLATED FINISH PLASTIC METAL COVER NON-HANDED NON-SIZED ACCESSIBILITY CYLINDER DELAYED ACTION*** AVB** REGULAR (DOUBLE) STANDARD (SINGLE) HOLD-OPEN FUSIBLE LINK *ARM FUNCTION EDA/HEDA CUSH/HCUSH SCUSH/SHCUSH DOUBLE EGRESS AVAILABLE NOT AVAILABLE Closer available with less than 5.0 lbs. opening force on 36 door. * Maximum opening/hold-open point with standard template. ** Advanced Variable Backcheck. *** Delay feature incorporates standard 4040 cylinder (not XP). LCN Door Control Catalog phone: n fax: n n rev. 11/16 B37

18 EDA mount 4" 102 mm 4040XP Series 2-1/4" 57 mm 3-1/2" 89 mm 5-1/4" 133 mm Mounting details B 14-1/16" 357 mm A 12-1/4" 311 mm EDA and CUSH Mounting 5-1/4" 133 mm 4040XP-18PA CUSH mount 4" 102 mm 2-1/4" 57 mm 3-1/2" 89 mm 5-1/4" 133 mm B 14-1/16" 357 mm 6" 152 mm A 12-1/4" 311 mm 5-1/2" 140 mm 4040XP-18PA Clearance Head Frame CUSH ARM Delayed Action Maximum Opening 4040XP-62EDA is 5-1/2 (140 mm) from door face. 6 (152 mm) for CUSH Flush or rabetted requires CUSH FLUSH PANEL ADAPTER, 4040XP-419 Requires SHOE SUPPORT, 4040XP-30 for fifth screw anchorage for narrow frames n Incorporates standard 4041 cylinder, without XP cylinder. n Delays closing from maximum opening to ; 115 with 180 template, 95 with 110 template, 85 with 100 template, 75 with 90 template. Delay time adjustable up to approximately 1 minute. EDA arm can be templated for points at: 110 : A = 6-3/8 (162 mm) B = 7-3/4 (197 mm) or 180 : A = 2-7/8 (73 mm) B = 4-1/4 (108 mm) Hold-open points up to maximum opening with HEDA arm Notes: 4040XP Series closers ordered with EDA or CUSH arms include 4040XP-201 FIFTH HOLE SPACER to support the shoe Spring Cush stop points are approximately 5 more than templated stop point Hold open at templated stop points CUSH arms can be templated for opening/hold-open point at: 85 : A = 7-15/16 (202 mm) B = 9-1/8 (232 mm) 90 : A = 7-3/16 (183 mm) B = 8-1/2 (216 mm) 100 : A = 6-1/16 (154 mm) B = 7-1/4 (184 mm) or 110 : A = 5-1/16 (129 mm) B = 6-3/8 (162 mm) LCN Door Control Catalog phone: n fax: n n rev. 11/16 B41

19 4040XP Series Accessories Cylinders Covers 4040XP-3071 Cast Iron Cylinder Assembly DEL Cast Iron Cylinder Assembly 4040XP-72 Plastic Cover 4040XP-72MC Metal Cover n Non-handed n Heavy duty n Used for delayed action closing n Non-handed n Includes 4040XP-54 snap-on cover clip n Non-handed n Handed n Required for plated finishes and custom powder coat finishes n Heavy duty n Standard n Optional Installation Accessories 4040XP-18 Plate 4040XP-18G Plate 4040XP-18TJ Plate 4040XP-18PA Plate n Required for hinge side mount where top rail is less than 3-3/4 (95 mm) n Requires minimum 2 (51 mm) minimum top rail n Locates top jamb mounted closer flush with top of head frame face in flush ceiling condition n Requires 1-3/4 (44 mm) minimum head frame n Centers top jamb mounted closer vertically on head frame where face is less than 3-1/2 (89 mm). Plate requires 1-3/4 (44 mm) minimum head frame n Required for parallel arm mounting where top rail is less than 5-1/2 (140 mm), measured from the stop n Requires 2 (51 mm) minimum top rail 4040XP-62PA PA Shoe n Required for parallel arm mounting B42 LCN Door Control Catalog phone: n fax: n n rev. 11/16 5/16

20 100 Series concealed overhead door holders/stops Reduced door prep Durable Improved corrosion resistance Function conversion kits are available Materials and finishes 100 Series heavy-duty Glynn-Johnson offers a complete line of overhead door holders and stops, accommodating virtually all openings with solutions for even the most complex door control problems. These concealed holders and stops provide the most attractive and reliable heavy-duty door control available. Glynn-Johnson 100 Series holders and stops provide the most reliable and versatile concealed overhead door control. They are designed for installation on virtually all types of doors mounted on conventional type butt hinges, pivots, continuous hinges, swing clear hinges and numerous other specialty hinges. When used in conjunction with many surface-applied door closers, 100 Series holders and stops provide the most effective control for entrance doors and vestibule doors of all types, as well as heavy or often used interior doors. Templates provided allow for variable mounting positions, ranging from of opening. Five models: 100H Series hold-open model 100HP Series internal hold-open model 100F Series friction hold-open model 100S Series stop-only model 100SE Series special stop-only model Six sizes: Each model comes in six sizes. Simple Standardized Three options: ADJ Adjustable jamb bracket CJ Jamb Bracket for use with LCN 5030 closer SOC Pin-in-socket security screw package Unmatched convenience: Non-handed Improved compatibility with door closers Single/double-acting doors Interior/exterior applications In heavy gauge brass or 300 Series stainless steel, these models offer the broadest range of finishes in the industry, complementing any design and offering the highest resistance to corrosion. Available in the following finishes: Finishes Description US3 Polished brass US4 Satin brass US10 Satin bronze US10B Oil rubbed bronze US32 Polished stainless steel US32D Satin stainless steel SP4 Powder coat brass SP10 Powder coat bronze SP28 Powder coat aluminum SP313 Powder coat dark bronze SPBLK Powder coat black Models These models provide a wide range of optional features, and are ideal for use on entrance and vestibule doors, large doors, doors opened frequently, or doors subject to abuse. These models are also furnished with an offsetstyle jamb bracket. Designed for heavy-duty applications, 100 Series models will provide long-lasting protection to doors, frames, hinges, related hardware and surrounding walls or obstructions. 100H Series hold-open (Suffix H) The hold-open function should be used where it is desired to hold a door open at a predetermined position for short or long periods of time, permitting an unobstructed traffic flow through the opening. These models are both selective and adjustable, featuring the most reliable hold-open mechanism available. They feature a control knob which protrudes from the face of the door and turns the hold-open function on or off. Set in the inactive position, the unit acts as a stop and shock absorber. The tension on the hold-open mechanism can be adjusted using an allen wrench to offset air currents or other exterior conditions. The hold-open tension adjustment is located in the bottom of the track in the top of the door. 18 Glynn-Johnson Door holders and stops

21 100HP Series internal hold-open These models provide a hold-open unit with the hold-open mechanism built into the channel, thus reducing the door prep. The 100HP have a preset hold-open force that is not adjustable. The hold-open feature is not selectable in these units, so the doors are always held open. 100F Series friction hold-open (Suffix F) Friction hold-open models provide an alternative holding method, ideal for heavy patient room doors, closet doors or similar applications where multiple hold-open positions are desired. The friction tension is adjusted using an allen wrench and an open end wrench. The friction tension adjustment is located on the top of the slider in the channel. 100S Series stop-only (Suffix S) When the hold-open function is not required, the stop-only function provides the same effective door control minus the hold-open feature. The stop-only model may be used on fire doors. 100SE Series special stop-only (Suffix SE) When stop-only models are used in conjunction with single point hold-open electronic door closers, they may be ordered without the shock-absorbing mechanism. Used as an auxiliary stop with these closers, they will prolong the life of the closer. The stop location is adjusted using an allen wrench on the stop block located in the channel. Note: Caution should be taken when using this option in other applications, as the elimination of the shock-absorbing spring can put added stress on the door and frame. Application Information UL Classification The 100 Series stop-only models are classified by Underwriters Laboratories (UL) as miscellaneous fire door accessories. This classification applies to use on either hollow metal fire doors or wood fire doors. Where wood door manufacturer s listing allows for the cutout required for installation, concealed overhead stops may be used on those wood fire doors. These units may be used on doors of any rating. As a reminder, the miscellaneous fire door accessories (GVUX) section is defined by UL as: Miscellaneous fire door accessories are intended in the individual listings. The accessories have been investigated to determine that when installed in accordance with the manufacturer s instructions, the accessories do not adversely affect the fire rating of the fire door and/or fire door frames." Dead stop templating If a wall or similar obstruction is in place at 110 or less opening angle (i.e. doors that open back-to-back), dead stop templating should be used. This includes all hold-open, friction and stop-only models, except when the SE option is used. The dead stop position is reached when the shock-absorbing spring is fully compressed, the initial degree of opening will be 5 to 7 less than the dead stop opening. Example: If the holder is templated to a 100 dead stop, the door will hold open at an angle between 93 and 95 but no further than 100. Note: Do not use dead-stop templating on the 100SE Series since there is no shock-absorbing spring. Environmental considerations Environmental factors should always be considered when specifying overhead holders and stops. Doors that are positioned on a building s exterior or subject to corrosive conditions should be equipped with a holder constructed primarily of stainless steel or brass materials. For interior applications, steel is acceptable, though brass substrates generally provide a more attractive architectural-grade finish. Options Suffix ADJ (adjustable jamb bracket) An additional option on the 100 Series is the adjustable jamb bracket, which allows the degree of hold-open or stop angle to be adjusted after installation. Suffix ADJ is available in all functions, but only in sizes 3, 4, 5 & 6. ADJ jamb bracket requires additional frame prep. The ADJ option cannot be added to an existing unit, it must be factory ordered. Suffix CJ (closer jamb bracket) Provides a special jamb bracket needed for 100 Series units used with LCN 5030 closers. These special jamb brackets are handed, so handing will need to be specified when ordering the CJ option, CJLH for a left hand door and CJRH for a right hand door. The CJ option cannot be added to an existing unit, it must be factory ordered. Suffix SOC (Pin-in-socket security screw package) A screw package with pin-in-socket screws for mounting the jamb bracket to the frame is provided instead of the standard screw package. Glynn-Johnson Door holders and stops 19

22 100 Series concealed overhead door holders/stops 3/4" 1/4" 2" 1" 1-1/4" 1" 1-1/4" 4-1/4" 3/4" 1-1/4" 1" 1/4" 3/8" 1/4" 2-3/8" 5-1/2" 3-1/2" 1/2" 12" 1-1/4" 3/8" 100 Series sizing chart Butts/offset pivots Center hung BHMA/ANSI, A156.8 & Fed. spec. cross reference G-J model BHMA * Fed. spec. Size Door opening Stop only Hold open Friction Note: This chart illustrates the most common types of hinging and door opening sizes. For unusual door details, contact Glynn-Johnson for availability. * These sizes are not available for use with offset pivots. Also not available with the ADJ option. * Wood doors with automatic flush bolts or roller latches, consult factory. Door opening Stop only Hold open Friction 1 18" - 23" 101S * 101H * 101F * " - 27" 102S * 102H * 102F * " - 33" 103S 103H 103F " - 39" 103S 103H 103F " - 39" 104S 104H 104F " - 45" 104S 104H 104F " - 45" 105S 105H 105F " - 51" 105S 105H 105F " - 51" 106S 106H 106F " - 59" 106S 106H 106F H C S C F C * First numeral (0) designates optional material. To specify: Brass material, change 0 to 1 (i.e. C11511) Stainless steel material, change 0 to 5 (i.e. C51511) BHMA: All 100 Series models are designed for heavy-duty applications and far exceed BHMA cycle test and force test requirements for Grade 1 holders and stops. The template information on this page is for reference only and is not intended to serve as an installation template. For complete dimensional information, refer to Glynn-Johnson template book. 20 Glynn-Johnson Door holders and stops

23 How to order 10 4 H US26D ADJ Overhead Series: 10 Size (door opening using butts or offset pivots): 1 (18" - 23") 2 ( " 27") 3 ( " 33") 4 ( " 39") 5 ( " 45") 6 ( " 54") Function: H HP F S SE Finishes: US3 US4 US10 US10B US32 US32D SP4 SP10 SP28 SP313 SPBLK Options: ADJ CJLH CJRH SOC Hold-open Internal hold-open Friction hold-open Stop-only Special stop-only Polished brass Satin brass Satin bronze Oil rubbed bronze Polished stainless Satin stainless steel Powder coat brass Powder coat bronze Powder coat aluminum Powder coat dark bronze Powder coat black Adjustable jamb bracket Special jamb bracket for LCN 5030 closer, LH door Special jamb bracket for LCN 5030 closer, RH door Pin-in-socket security screws Glynn-Johnson Door holders and stops 21

24 290_SSTOP Copyright 2008 Pemko Manufacturing Co. All rights reserved. Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited. 290_SSTOP_PDF Rev

25 SEUILS D ALUMINIUM SÉRIE AB HOMOLOGATIONS: 1/2'' [12.7mm] 6 7/8" [174.6mm] Descrip on: NOM: SEUIL AB7 MATÉRIEL: ALUMINIUM ALLIAGE 6063 T5 FINIS DISPONIBLE: ALUMINIUM NATUREL SEULEMENT LARGEUR: 6 7/8 LONGUEUR DISPONIBLE: 3, 42,4, 5, 6, 7, 8, 9, 10 & 12 COUPÉ SEUL. OU COUPÉ, PERCÉ AVEC VIS

26 SEUILS D ALUMINIUM SÉRIE AB HOMOLOGATIONS: 1/2'' [12.7mm] 2 7/8'' [73mm] Descrip on: NOM: SEUIL AB3 MATÉRIEL: ALUMINIUM ALLIAGE 6063 T5 FINIS DISPONIBLE: ALUMINIUM NATUREL SEULEMENT LARGEUR: 2 7/8 LONGUEUR DISPONIBLE: 3, 42,4, 5, 6, 7, 8, 9, 10 & 12 COUPÉ SEUL. OU COUPÉ, PERCÉ AVEC VIS

27 SEUILS D ALUMINIUM SÉRIE AB HOMOLOGATIONS: 1/2'' [12.7mm] 2 3/4'' [69.8mm] Descrip on: NOM: SEUIL AB33 MATÉRIEL: ALUMINIUM ALLIAGE 6063 T5 FINIS DISPONIBLE: ALUMINIUM NATUREL SEULEMENT LARGEUR: 2 3/4 LONGUEUR DISPONIBLE: 3, 42,4, 5, 6, 7, 8, 9, 10 & 12 COUPÉ SEUL. OU COUPÉ, PERCÉ AVEC VIS

28 SEUILS D ALUMINIUM BRIS THERMIQUE HOMOLOGATIONS: 1/4'' [6.4mm] Descrip on: NOM: ABBT MATÉRIEL: PVC (POLYCHLORURE DE VINYLE) FINIS DISPONIBLE: BLANC LARGEUR: 1/4 LONGUEUR DISPONIBLE: 3, 42,4, 5, 6, 7, 8, 9, 10 & 12 COUPÉ SEUL.

29

30

31