Dual-Rod Cylinder Compact Type

Transcription

1 CAT.EUS20-7 B -UK Dual-Rod Cylinder Compact Type New Made to Order additionally released. (For details, refer to page 22.) Auto switch can be installed from 3 directions. Reverse Series CXSJ/ø, ø0, ø,, ø2, ø32 Dimensions/Weight CXSJ CXS Height (CXSJ) Height (CXS) Symmetric mounting Width (CXSJ) Width (CXS) Full length (CXSJ) Full length (CXS) Reverse mounting mechanism Reversible Bolt holder Auto switch Mounting bolt Bolt holder Axial piping available (ø, ø0) Since the bolt holder is movable, the mounting bolt does not interfere with the auto switch no matter what direction it is mounted from. Bore size Dimensions (mm) Series (mm) Height Width Full length ø CXSJ Stroke CXS Stroke ø0 CXSJ0 2 + Stroke CXS Stroke ø CXSJ Stroke CXS Stroke CXSJ Stroke CXS Stroke ø2 CXSJ Stroke CXS Stroke ø32 CXSJ Stroke CXS Stroke Note) Slide bearing, 20 mm strokes Note) Weight (kg) Allowable kinetic energy, allowable load and non-rotating accuracy are equivalent to those of the CXS basic type.

2 Dual-Rod Cylinder Compact Type Series CXSJ ø, ø0, ø,, ø2, ø32 How to Order TN TF Port thread type M thread ø to ø2 Rc/ NPT/ ø32 G/ Piping P Standard (ø to ø32) Axial (ø, ø0) Standard piping Port location Axial piping Port location CXSJ M P 0 M9BW S Compact type M L Bearing type Slide bearing Ball bushing bearing Number of auto switches S n 2 pcs. pc. n pcs. Auto switch Without auto switch (with built-in magnet) Refer to the table below for auto switch model numbers. Made to Order (Refer to page 2 and 22.) Bore size / Stroke (mm) Bore size Standard stroke 0, 20, 30, 0, 0 0 0, 20, 30, 0, 0, , 20, 30, 0, 0, 7, Applicable Auto es/refer to page for detailed auto switch specifications. Type Reed switch Solid state switch Special function Electrical entry Grommet Grommet Indicator light Yes None Yes Wiring Load voltage Auto switch model (output) DC AC Perpendicular In-line 3-wire (NPN equiv.) V A9V A9 2-wire 2 V 00 V A93V A93 2 V V, 2 V 00 V or less A90V A90 3-wire (NPN) M9NV M9N V, 2 V 3-wire (PNP) M9PV M9P 2-wire 2 V M9BV M9B 3-wire (NPN) 2 V M9NWV M9NW V, 2 V M9PWV M9PW M9BWV M9BW M9BA Diagnostic indication 3-wire (PNP) (2-color display) 2-wire 2 V Water resistant (2-color display) Lead wire length symbols 0. m... Nil (Example) M9N m... M M9NWM 3 m... L M9NL m... Z M9NZ Since there are applicable auto switches other than listed, refer to page for details. For details about switch with pre-wired connector, refer to SMC S Best Pneumatics catalogue. Auto switches are included when shipped (but not assembled). Lead wire length (m) 0. (M) 3 (L) (Z) Pre-wired connector Applicable load IC circuit IC circuit IC circuit IC circuit Solid state switches marked with are produced upon receipt of order. Relay, PLC Relay, PLC

3 Dual-Rod Cylinder Compact Type Series CXSJ Specifications Bore size (mm) Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Piston speed Cushion Stroke adjustable range Port size Air (Non-lube).0 MPa 0.7 MPa 0. MPa 0. MPa 0.0 MPa 30 to 00 mm/s 0 to 0 C (No freezing) 30 to 700 mm/s 30 to 00 mm/s Rubber bumper on both ends 0 to mm compared to the standard stroke M3 M Rc (NPT, PF) / Standard Stroke (mm) Model Standard stroke Manufacturable stroke range CXSJ CXSJ0 0, 20, 30, 0, 0 0, 20, 30, 0, 0, 7 0 to 00 0 to 0 CXSJ 0 to 0 0, 20, 30, 0, 0, 7, 00 CXSJ20, 2, 32 0 to 200 Strokes beyond the standard stroke range are available as a special order. Made to Order (For details, refer to page 22.) Symbol Specifications XB Heat resistant cylinder ( 0 to 0 C) XB3 Low speed cylinder ( to 0 mm/s) XC Note) Made of stainless steel Intermediate stroke (with mm width XC9 spacer) XC22 Fluoro rubber seals Note) Slide bearing type only Theoretical Output Bore size Rod size Operating Piston area Operating pressure (MPa) (mm) (mm) direction (mm 2 ) CXS CXS0 CXS CXS20 CXS2 CXS OUT OUT OUT OUT OUT OUT IN IN IN IN IN IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) (N) Weight Model Standard stroke (mm) CXSJM CXSJL CXSJM0 CXSJL0 CXSJM CXSJL CXSJM20 CXSJL20 CXSJM2 CXSJL2 CXSJM32 CXSJL Note) For axial piping of CXSJP- and CXSJ0P-, please add the following weight. CXSJP-: kg, CXSJ0P-: 0.0 kg (kg)

4 Series CXSJ Model Selection Caution Theoretical output must be confirmed separately, referring to the table on page 2. Vertical Mounting L L Mounting orientation m m Max. speed (mm/s) Stroke (mm) Selection graph ø ø0 ø ø2 ø32 Up to 200 Up to 00 Up to 00 Up to 00 All strokes z x c v Horizontal Mounting L Mounting orientation m m Refer to the caution notes below. Stroke (mm) Max. speed (mm/s) Selection graph ø ø0 ø ø2 ø32 Caution Up to 0 Up to 30 Up to 0 Up to 00 Over 00 Up to 00 Over 00 Up to 00 Over 00 b n m, If the cylinder is horizontally mounted and the plate end does not reach the load s center of gravity, use the formula below to calculate the imaginary stroke L' that includes the distance between the load s center of gravity and the plate end. Select the graph that corresponds to the imaginary stroke L'. Imaginary stroke L' = (Stroke) + k + L k: Distance between the center and end of the plate ø 2.7 mm ø0 mm ø mm ø2 mm ø32 mm (Example) q When using CXSJM-0 and L = mm: Imaginary stroke L' = = 27.7 Therefore, the graph used for your model selection should be the one for CXSJM-30 n). w When using CXSJL2-0 and L = 0 mm: Imaginary stroke L' = = 7 Therefore, the graph used for your model selection should be the one for CXSJL2-7 ). Up to 7 Up to 00 Over 00 The maximum speeds for ø to ø32 are: ø, ø0: up to 00 mm/s; ø, : up to 700 mm/s; ø2, ø32: up to 00 mm/s L k Up to 00 Up to 00 Over 00 3

5 Dual-Rod Cylinder Compact Type Series CXSJ Vertical Mounting Graphz V = 200 (mm/s) CXSJM CXSJL Graphx V = 00 (mm/s) CXSJM CXSJL 20 0 ø32 ø32 ø2 Weight m (kg) ø2 ø Weight m (kg) ø ø0 ø ø ø Overhang L (mm) Overhang L (mm) Graphc V = 00 (mm/s) CXSJM CXSJL Graphv V = 00 (mm/s) (V = 700 mm/s for ø, ) CXSJM CXSJL ø32 ø2 0. ø 0. ø Weight m (kg) ø0 Weight m (kg) 0. ø0 0. ø ø Overhang L (mm) Overhang L (mm) Note) V = 700 mm/s for ø,.

6 Series CXSJ Horizontal Mounting Graphb Up to 0 mm stroke 0.2 V = Up to 00 mm/s V = Up to 00 mm/s Graphn Up to 30 mm stroke 0.2 V = Up to 00 mm/s V = Up to 00 mm/s Weight m (kg) Weight m (kg) CXSJM CXSJL CXSJM CXSJL Overhang L (mm) Overhang L (mm) Graph, V = Up to 00 mm/s; Up to 0 mm stroke CXSJM CXSJL Graph. V = Over 00 mm/s; Up to 0 mm stroke CXSJM CXSJL Weight m (kg) 0. ø32 ø2 Weight m (kg) 0. ø32 ø2 ø ø ø Overhang L (mm) Overhang L (mm) ø0 Graph 2 V = Up to 00 mm/s; Up to 0 mm stroke CXSJM CXSJL Graph 3 V = Over 00 mm/s; Up to 0 mm stroke CXSJM CXSJL Weight m (kg) 0. ø32 ø2 Weight m (kg) 0. ø32 ø2 ø ø ø Overhang L (mm) Overhang L (mm) ø0

7 Dual-Rod Cylinder Compact Type Series CXSJ Graphm Up to 0 mm stroke 0.2 V = Up to 00mm/s 0. Weight m (kg) CXSJM CXSJL Overhang L (mm) 0 Graph 0 V = Up to 00 mm/s; Up to 30 mm stroke CXSJM CXSJL Graph V = Over 00 mm/s; Up to 30 mm stroke CXSJM CXSJL Weight m (kg) 0. ø32 ø2 Weight m (kg) 0. ø32 ø2 ø ø ø ø0 Overhang L (mm) Overhang L (mm) Graph V = Over 00 mm/s; Up to 7 mm stroke CXSJM CXSJL Graph V = Over 00 mm/s; Up to 00 mm stroke CXSJM CXSJL Weight m (kg) ø ø32 ø2 ø Weight m (kg) ø32 ø2 ø Overhang L (mm) Overhang L (mm)

8 Series CXSJ Construction: Standard Piping CXSJM (Slide bearing) CXSJM CXSJL (Ball bushing bearing) @ t! y!0! e u!7 o i!3 CXSJM0 r u!7 o i!3 o o i Rod cover Piston rod B-side piston Rod cover Piston rod B-side piston Component Parts: Standard Piping No. Description Material Note No. Description Material Note 2 3 Housing Piston rod A Piston rod B Aluminium alloy Carbon steel Note) Carbon steel Note) Hard anodised Hard chromium electroplated Hard chromium electroplated 7 Bumper B Piston seal Rod seal Polyurethane NBR NBR Rod cover Aluminium bearing alloy 9 O-ring NBR Head cover Aluminium alloy anodised 20 O-ring NBR Plate Aluminium alloy Glossy, self-colouring hard anodised 2 Seal retainer Stainless steel 7 Piston A Aluminium alloy Chromated 22 Retaining ring B Special steel Nickel plated Piston B Aluminium alloy Chromated 23 Bolt holder Stainless steel 9 Magnet Magnetic material 2 Bearing spacer Aluminium bearing alloy 0 Bumper bolt Carbon steel Nickel plated 2 Ball bushing Hexagon nut Carbon steel Nickel plated 2 Piston rod A Special steel Hard chromium electroplated 2 Bumper Polyurethane 27 Piston rod B Special steel Hard chromium electroplated 3 Hexagon socket head cap screw Chromium steel Nickel plated 2 O-ring NBR Hexagon socket head set screw Chromium steel Nickel plated 29 Piston C Stainless steel Retaining ring Special steel Nickel plated 30 Bumper holder Resin Note) Stainless steel for CXSJM. Replacement Parts: Seal Kit Model Seal kit no. CXSJM CXSJM-PS CXSJL CXSJL-PS CXSJM0 CXSJM0-PS CXSJL0 CXSJL0-PS Contents Items!7,!, from the chart above 7

9 Dual-Rod Cylinder Compact Type Series CXSJ Construction: Standard Piping CXSJM (Slide bearing) CXSJM!2!!0 r! i o u!7 t! CXSJL (Ball bushing io u!7 t! y! e q!3 q!3 CXSJM20 to 32 CXSJL20 to r! i o u!7 #0! i o u!7 t! Rod cover Head cover Rod cover Head cover Component Parts: Standard Piping No. Description Material Note No. Description Material Note Housing Aluminium alloy Hard anodised Bumper B Polyurethane 2 Piston rod A Carbon steel Hard chromium electroplated 7 Piston seal NBR 3 Piston rod B Carbon steel Hard chromium electroplated Rod seal NBR Rod cover Aluminium bearing alloy 9 O-ring NBR Head cover Special steel 20 O-ring NBR Plate Aluminium alloy Glossy, self-colouring hard anodised 2 Seal retainer Stainless steel 7 Piston A Aluminium alloy Chromated 22 Retaining ring B Special steel Nickel plated Piston B Stainless steel 23 Bolt holder Stainless steel 9 Magnet Magnetic material 2 Bearing spacer Resin 0 Bumper bolt Carbon steel Nickel plated 2 Ball bushing Hexagon nut Carbon steel Nickel plated 2 Piston rod A Special steel Hard chromium electroplated 2 Bumper Polyurethane 27 Piston rod B Special steel Hard chromium electroplated 3 Hexagon socket head cap screw Chromium steel Nickel plated 2 O-ring NBR Hexagon socket head set screw Chromium steel Nickel plated 29 Piston C Stainless steel Retaining ring Special steel Nickel plated 30 Bumper holder Resin Replacement Parts: Seal Kit Model Seal kit no. CXSJM CXSM-PS CXSJM20 CXSM20-PS CXSJM2 CXSM2-PS CXSJM32 CXSM32-PS CXSJL CXSLAPS CXSJL20 CXSL20APS CXSJL2 CXSL2APS CXSJL32 CXSL32APS Contents Items!7,!, and!9 from the chart above

10 Series CXSJ Construction: Axial Piping CXSJP, CXSJ0P e r w t q o i y u Component Parts: Axial Piping No. Description Material Note Cover Adapter Hexagon socket head cap screw Hexagon socket head plug O-ring O-ring Steel ball Steel ball Steel ball Aluminium alloy Aluminium alloy Chromium steel Chromium steel NBR NBR Special steel Special steel Special steel Hard anodised Anodised Nickel plated Nickel plated Hard chromium electroplated Hard chromium electroplated Hard chromium electroplated Parts other than those listed above are the same as those of CXSJ basic type. Clean Series There are two types of cylinders, relieving type and vacuum type, available for a clean room environment. The relieving type specification with the double-seal construction of the rod section allows the cylinder to channel exhaust through the relief port directly to the outside of a clean room environment. The vacuum type specification allows the application of vacuum on the rod section while forced exhaust of air takes place through the vacuum port to the outside of a clean room environment. How to Order CXSJ M Bore size Stroke Auto switch Bore size / Stroke 0, 20, 30, 0, 0 0 0, 20, 30, 0, 0 Bearing type M Slide bearing L Ball bushing bearing Only ball bushing bearing is Specifications available for clean room Bore size (mm) 0 specification 2-. Proof pressure.0 MPa Maximum operating pressure 0.7 MPa Clean room specifications Minimum operating pressure 0. MPa 0. MPa Vacuum type 2 Relieving type (with specially treated sliding parts) Ambient and fluid temperature 0 to 0 C (No freezing) Piston speed 30 to 00 mm/s Stroke adjustable range 0 to mm compared to the standard stroke Bearing type Slide bearing, Ball bushing bearing Refer to SMC Clean Series catalogue for dimensions. 9

11 Dual-Rod Cylinder Compact Type Series CXSJ Dimensions: ø Standard Piping 2 x M3 through 2.7 (2) ( + Stroke) Stroke Stroke 32 + Stroke 2 + Stroke Bolt holder x M3 through Stroke -M3 thread depth ± ± ø 2 ±0.2 2 x M3 through ø3. through ø. counterbore with depth (Opposite side: Same) M3 thread depth 3 (Piping port) For bolt holder, refer to back page, Mounting. 0

12 Series CXSJ Dimensions: ø0 Standard Piping 2 x M3 through () ( + Stroke) Stroke + Stroke Stroke 3 + Stroke Bolt holder 2 + Stroke x M3 x thread depth ± ±0.2 ø 33 ±0.2 2 x M3 through ø3. through ø. counterbore with depth. (Opposite side: Same). 2 x M through 2. 2 x M thread depth (Piping port) For bolt holder, refer to back page, Mounting.

13 Dual-Rod Cylinder Compact Type Series CXSJ Dimensions: ø, ø0 Axial Piping CXSJP.7 ST (9 + Stroke) 2 + Stroke 32 + Stroke 2 + Stroke 7 Steel balls ST (. + Stroke) + Stroke. + Stroke + Stroke Steel balls x M. x L 2 x M3 thread depth 3 (Piping port) OUT 3. IN Stroke CXSJ0P. 2 + Stroke x M. x L 20 2 x M thread depth (Piping port) OUT IN 2

14 Series CXSJ Dimensions: ø to 32 Standard Piping N (i) (L) (Z) Stroke ZZ + Stroke J K SS + Stroke I L Z M Q (G) H A G ± 0.2 NN C (G) B D N U E F (Through) R T Bore size (mm) A B ZZ C D E F 2 x M 2 x M 2 x M 2 x M G H I J K 2... L M 2 x 2 x ø.3 through 2 x 2 x ø counterbore with depth.3 2 x 2 x ø. through 2 x 2 x ø9. counterbore with depth.3 2 x 2 x ø. through 2 x 2 x ø counterbore with depth.3 2 x 2 x ø. through 2 x 2 x ø counterbore with depth.3 N 2 x M with thread depth 2 x M with thread depth 2 x M with thread depth 7. 2 x M with thread depth 7. NN ø ø0 ø2 ø Q R 3 T U 2 x M with thread depth 2 x M with thread depth 2 x M with thread depth 2 x Rc/ with thread depth SS Bore size (mm) Symbol Stroke Z

15 Dual-Rod Cylinder Compact Type Series CXSJ Auto Proper Mounting Position for Stroke End Detection CXSJ, 0 A B C D Operating Range Auto switch model D-A9, D-A9V D-M9BAL D-M9, D-M9V D-M9W, D-M9WV Bore size The operating ranges are provided as guidelines including hystereses and are not guaranteed values (assuming approximately ±30% variations). They may vary significantly with different environments. (mm) CXSJ to 32 B D Bore size (mm) D-A90, D-A9 A B 9. C D A D-A93 B 9. C D D-M9, D-M9W, D-M9V, D-M9WV, D-M9BA D-M9BAV A B C D A B C D A Electrical entry direction: Inward C Electrical entry direction: Outward Note ) ø: D-A90, A9, A93, M9BAL ø0: D-A90, A9, A93 Only outward electrical entry (D dimension) is available. Note 2) Minus value in D column (ø,, ø2, ø32) means that the auto switches are to be mounted beyond the cylinder body edges. Note 3) When setting an auto switch, confirm the operation and adjust its mounting position. Auto switch mounting dimensions CXSJ, 0 A D-A9 (Reed switch) B D-M9W D-M9 (Solid state switch) C C3 D-A9V (Reed switch) C2 D D2 D-M9V D-M9WV (Solid state switch) Auto switch model D-A9 D-M9, D-M9W, D-M9BA D-A9V D-M9V, D-M9WV D-M9BAV Symbol A B C, D C2, C3, D2 C, D C2, C3, D2 (mm) Bore size 0.. CXSJ to 32 A D-A9 (Reed switch) D-M9 (Solid state switch) D-M9W C C3 C2 D-A9V (Reed switch) D-M9WV (Solid state switch) Auto switch model D-M9, D-M9W, D-M9BA D-A9V, D-M9BAV D-M9WV Symbol A C C2 C3 Bore size (mm) 32..

16 Series CXSJ Auto Mounting Watchmaker s screwdriver Set screw Auto switch Use a watchmaker s screwdriver with a handle to mm in diameter when tightening the auto switch mounting screw. Tightening torque should be approximately 0.0 to 0.20 N m. Caution q Avoid proximity to magnetic objects. When magnetic substances such as iron (including flange brackets) are in close proximity to an auto switch cylinder (switch mounting side), be sure to provide a clearance between the magnetic substance and the cylinder body as shown in the drawing below. If the clearance is less than 0 mm, the auto switch may not function properly. w For CXSJ/0, the switch cannot be attached or detached from the plate side if the middle groove (indicated by arrows in the figure on the right) is used. (It will interfere with the bumper bolt at the end of the groove.) 0 mm 0 mm Apart from the applicable auto switches listed in How to Order, the following auto switches can be mounted. Normally closed (N.C. = b contact), solid state switches (D-F9G and D-F9H type) are also available. For details, refer to Best Pneumatics catalogue.

17 Series CXSJ Auto Specifications Auto Common Specifications Type Leakage current Operating time Impact resistance Insulation resistance Withstand voltage Ambient temperature Enclosure Standard Reed switch Solid state switch None 3-wire: 00 µa or less 2-wire: 0. ma or less.2 ms 300 m/s 2 up to ms 000 m/s 2 0 MΩ or more at 00 VDC Mega (between the lead wire and the case) 00 VAC for minute (between the lead wire and the case) 000 VAC for minute (between the lead wire and the case) 0 to 0 C IEC29 standard IP7, JIS C 0920 waterproof construction Conforming to CE Standards Lead Wire Length Lead wire length indication (Example) D-M9BW L Lead wire length 0. m M m L 3 m Z m Contact Protection Boxes: CD-P, CD-P2 <Applicable switch model> D-A9/A9V type The auto switches below do not have a built-in contact protection circuit. Therefore, please use a contact protection box with the switch in any of the following cases: q Where the operation load is an inductive load. w Where the wiring length to load is greater than m. e Where the load voltage is 00 VAC. The contact life may be shortened (due to permanent energising conditions). Since the solid state auto switch is a semiconductor switch which has no contacts, no contact protection box is needed. Note ) Applicable auto switch with m lead wire Z Solid state switch: Manufactured upon receipt of order as standard. Note 2) To designate solid state switches with flexible specifications, add - after the lead wire length. Flexible cable is used for D-M9(V), D- M9W(V) as standard. There is no need to place the suffix - to the end of part number. Specifications Part no. Load voltage Max. load current CD-P 00 VAC 200 VAC 2 ma 2. ma Lead wire length connection side 0. m Load connection side 0. m CD-P2 2 VDC 0 ma Internal Circuit CD-P Surge absorber Choke coil OUT OUT CD-P2 Zener diode Choke coil OUT (+) OUT ( ) Dimensions Connection To connect a switch unit to a contact protection box, connect the lead wire from the side of the contact protection box marked SWITCH to the lead wire coming out of the switch unit. Keep the switch as close as possible to the contact protection box, with a lead wire length of no more than meter.

18 Basic Wiring Auto Connections and Examples Solid state 3-wire, NPN main circuit Load Solid state 3-wire, PNP main circuit Load 2-wire (Solid state) main circuit Load 2-wire (Reed) Indicator light protective circuit etc. Load (Power supplies for switch and load are separate.) main circuit Load main circuit Load Indicator light protective circuit etc. Load Example of Connection to PLC (Programmable Logic Controller) Sink input specification 3-wire, NPN Input Source input specification 3-wire, PNP Input Connect according to the applicable PLC input specifications, since the connection method will vary depending on the PLC input specifications. 2-wire COM Input PLC internal circuit 2-wire COM Input PLC internal circuit COM PLC internal circuit COM PLC internal circuit Example of AND (Serial) and OR (Parallel) Connection 3-wire AND connection for NPN output (using relays) 2 Relay Relay Load Relay contact AND connection for NPN output (performed with switches only) Load 2 OR connection for NPN output 2 Load The indicator lights will illuminate when both switches are turned ON. 2-wire with 2-switch AND connection 2-wire with 2-switch OR connection When two switches are connected in series, the load (Solid state) When two switches Load may malfunction because Load are connected in parallel, a malfunction may the load voltage could decrease when beign in the ON occur because the state. load voltage could increase when beign in The indicator lights will illuminate if both of the switches 2 2 the OFF state. are in the ON state. Power supply Residual Load voltage at ON = x 2 pcs. voltage voltage = 2 V - V x 2 pcs. = V Example: The Power supply is 2 VDC. The Internal voltage drop in the switch is V. Load voltage at OFF = Leakage current x 2 pcs. x Load impedance = ma x 2 pcs. x 3 kω = V Example: The Load impedance is 3 kω. The Leakage current from the switch is ma. (Reed) Because there is no current leakage, the load voltage will not increase when turned OFF. However, depending on the number of switches in the ON state, the indicator lights may sometimes dim or not light because of the dispersion and reduction of the current flowing to the switches. 7

19 Reed : Direct Mounting Style D-A90(V)/D-A93(V)/D-A9(V) Grommet Caution Operating Precautions Fix the switch with the existing screw installed on the switch body. The switch may be damaged if a screw other than the one supplied is used. Auto Internal Circuit D-A90(V) Reed switch Contact protection box CD-P CD-P2 OUT (±) OUT (±) Auto Specifications PLC: Programmable Logic Controller D-A90/D-A90V (Without indicator light) Auto switch part no. D-A90 D-A90V D-A90 D-A90V D-A90 D-A90V Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Applicable load IC circuit, Relay, PLC Load voltage 2 VAC/DC or less VAC/DC or less 00 VAC/DC or less Maximum load current 0 ma 0 ma 20 ma Contact protection circuit None Internal resistance Ω or less (including lead wire length of 3 m) Standard Conforming to CE Standards D-A93/D-A93V/D-A9/D-A9V (With indicator light) Auto switch part no. D-A93 D-A93V D-A93 D-A93V D-A9 D-A9V Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Applicable load Relay, PLC IC circuit Load voltage 2 VDC 00 VAC to VDC Load current range and max. load current to 0 ma to 20 ma 20 ma Contact protection circuit None Internal voltage D-A93 2. V or less (to 20 ma)/3 V or less (to 0 ma) drop D-A93V 2.7 V or less 0. V or less Indicator light Red LED illuminates when turned ON. Standard Conforming to CE Standards Lead wires D-A90(V)/D-A93(V) Oilproof heavy-duty vinyl cable: ø2.7, 0. mm 2 x 2 cores (, ), 0. m D-A9(V) Oilproof heavy-duty vinyl cable: ø2.7, 0. mm 2 x 3 cores (,, ), 0. m Note ) Refer to page for reed switch common specifications. Note 2) Refer to page for lead wire lengths. Weight Unit: g D-A93(V) Reed switch LED diode Resistor Zener diode Contact protection box CD-P CD-P2 OUT (+) OUT ( ) Auto switch part no. Lead wire length 0. (m) 3 Dimensions D-A90/D-A93/D-A9 2. D-A90(V) 30 2 ø2.7 D-A93(V) 30 D-A9(V) Unit: mm D-A9(V) Note) q In case the operation load is an inductive load. w In case the wiring load is greater than m. e In case the load voltage is 00 VAC. Use the auto switch with a contact protection box in any of the above mentioned cases. (For details about the contact protection box, refer to page.). M2. x l Slotted set screw D-A90V/D-A93V/D-A9V 22 (2.) Indicator light D-A90 type comes without indicator light. 0 M2. x l Slotted set screw Most sensitive position ø2.7 ( ): Dimensions for D-A93 Indicator light D-A90V type comes without indicator light. 9. DC (+) LED diode Resistor Load Reverse OUT current prevention diode Reed switch DC ( ) (+) DC power supply ( ). 0 Most sensitive position

20 Solid State : Direct Mounting Style D-M9N(V)/D-M9P(V)/D-M9B(V) Grommet 2-wire load current is reduced (2. to 0 ma). Lead-free UL certified lead cable (style 2) is used. Flexibility is. times greater than the conventional model (SMC comparison). Using flexible cable as standard spec. Auto Specifications PLC: Programmable Logic Controller D-M9/D-M9V (With indicator light) Auto switch part no. D-M9N D-M9NV D-M9P D-M9PV D-M9B D-M9BV Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Wiring type 3-wire 2-wire Output type NPN PNP Applicable load Power supply voltage Current consumption IC circuit, Relay, PLC, 2, 2 VDC (. to 2 V) 0 ma or less 2 VDC relay, PLC Load voltage 2 VDC or less 2 VDC (0 to 2 VDC) Load current Internal voltage drop 0 ma or less 0. V or less 2. to 0 ma V or less Leakage current 00 µa or less at 2 VDC 0. ma or less Indicator light Standard Red LED illuminates when turned ON. Conforming to CE Standards Lead wires Oilproof flexible heavy-duty vinyl cable: ø2.7 x 3.2 ellipse D-M9B(V) 0. mm 2 x 2 cores D-M9N(V), D-M9P(V) 0. mm 2 x 3 cores Note ) Refer to page for solid state switch common specifications. Note 2) Refer to page for lead wire lengths. Weight Unit: g Caution Operating Precautions Fix the switch with the existing screw installed on the switch body. The switch may be damaged if a screw other than the one supplied is used. Auto Internal Circuit D-M9N(V) Auto switch part no. Lead wire length (m) Dimensions D-M D-M9N(V) D-M9P(V) Mounting screw M2. x l Slotted set screw Indicator light D-M9B(V) Unit: mm DC (+) main circuit OUT D-M9P(V) main circuit DC ( ) DC (+) OUT DC ( ) D-M9V Most sensitive position 22 Mounting screw M2. x l Indicator light Slotted set screw D-M9B(V) OUT (+) 2. Most sensitive position 20 main circuit OUT ( ) 9

21 2-Colour Indication Solid State : Direct Mounting Style D-M9NW(V)/D-M9PW(V)/D-M9BW(V) Grommet 2-wire load current is reduced (2. to 0 ma). RoHS compliant UL certified lead cable (style 2) is used. Flexibility is. times greater than the conventional model (SMC comparison). Using flexible cable as standard spec. The optimum operating position can be determined by the colour of the light. (Red Green Red) Auto Specifications PLC: Programmable Logic Controller D-M9W/D-M9WV (With indicator light) Auto switch part no. D-M9NW D-M9NWV D-M9PW D-M9PWV D-M9BW D-M9BWV Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Wiring type Output type 3-wire NPN PNP 2-wire Applicable load Power supply voltage Current consumption IC circuit, Relay, PLC, 2, 2 VDC (. to 2 V) 0 ma or less 2 VDC relay, PLC Load voltage 2 VDC or less 2 VDC (0 to 2 VDC) Load current 0 ma or less 2. to 0 ma Internal voltage drop Leakage current 0. V or less at 0 ma (2 V or less at 0 ma) 00 µa or less at 2 VDC V or less 0. ma or less Indicator light Standard Operating position... Red LED illuminates. Optimum operating position... Green LED illuminates. Conforming to CE Standards Lead wires Oilproof flexible heavy-duty vinyl cable: ø2.7 x 3.2 ellipse D-M9BW(V) 0. mm 2 x 2 cores D-M9NW(V), D-M9PW(V) 0. mm 2 x 3 cores Note ) Refer to page for solid state switch common specifications. Note 2) Refer to page for lead wire lengths. Weight Unit: g Auto Internal Circuit D-M9NW(V) main circuit DC (+) OUT DC ( ) Auto switch part no. Lead wire length (m) Dimensions D-M9W 0. 3 D-M9NW(V) Mounting screw M2. x l Slotted set screw D-M9PW(V) D-M9BW(V) Unit: mm D-M9PW(V) DC (+) 2. Indicator light main circuit OUT D-M9BW(V) DC ( ) OUT (+) OUT ( ) Indicator light / Display method Operating range main circuit ON OFF D-M9WV 3.2 Most sensitive position 22 Indicator light Mounting screw M2. x l Slotted set screw Most sensitive position Display Red Green Red Optimum operating position

22 Water Resistant 2-Colour Indication Solid State : Direct Mounting Style D-M9NA(V)/D-M9PA(V)/D-M9BA(V) Grommet Water (coolant) resistant type 2-wire load current is reduced (2. to 0 ma). RoHS compliant UL certified (style 2) lead cable is used. Auto Internal Circuit D-M9NA(V) D-M9PA(V) D-M9BA(V) DC (+) OUT DC ( ) DC (+) OUT DC ( ) OUT (+) OUT ( ) Indicator light / Display method Operating range main circuit main circuit main circuit ON Display Red Green Red OFF Optimum operating position Auto Specifications PLC: Programmable Logic Controller D-M9A/D-M9AV (With indicator light) Auto switch part no. Electrical entry direction D-M9NA In-line D-M9NAV Perpendicular D-M9PA In-line D-M9PAV Perpendicular D-M9BA In-line D-M9BAV Perpendicular Wiring type 3-wire 2-wire Output type Applicable load NPN PNP IC circuit, Relay, PLC 2 VDC relay, PLC Power supply voltage Current consumption, 2, 2 VDC (. to 2 V) 0 ma or less Load voltage Load current 2 VDC or less 0 ma or less 2 VDC (0 to 2 VDC) 2. to 0 ma Internal voltage drop Leakage current 0. V or less at 0 ma (2 V or less at 0 ma) 00 µa or less at 2 VDC V or less 0. ma or less Indicator light Solid State Specifications Leakage current 3-wire: 00 µa or less 2-wire: 0. ma or less Operating time Impact resistance Insulation resistance Withstand voltage Ambient temperature Enclosure ms or less 000 m/s 2 0 MΩ or more at 00 VDC Mega (between lead wire and case) 000 VAC for minute (between lead wire and case) 0 to 0 C IEC029 standard IP7, JIS C 0920 waterproof construction Weight Auto switch part no. Lead wire length (m) 0. 3 Model no. D-M9 Wiring/Output type N P B Operating position... Red LED illuminates. Optimum operating position... Green LED illuminates. Lead wires Oilproof heavy-duty vinyl cable: ø2.7 x 3.2 ellipse D-M9BA(V) 0. mm 2 x 2 cores D-M9NA(V), D-M9PA(V) 0. mm 2 x 3 cores D-M9NA(V) How to Order 3-wire NPN 3-wire PNP 2-wire N A Note ) 0. m, m, m are produced upon receipt of order. With pre-wired connector is also available. For details, refer to SMC Information 0-E27-. D-M9PA(V) V L - V - M L Z D-M9BA(V) Lead wire length 0. m Note ) m Note ) 3 m m Note ) In-line Perpendicular Unit: g Electrical entry direction 2

23 Made to Order Symbol Heat Resistant Cylinder ( 0 to 0 C) XB The air cylinder has been changed the seal material and grease, so that it could be used even at higher temperatures up to 0 C from 0 C. How to Order Standard model no. XB Heat resistant cylinder Specifications Ambient temperature range 0 to 0 C Seal material Fluoro rubber Grease Heat resistant grease Specifications other than above and external dimensions Note ) Operate without the lubrication of a pneumatic system lubricator. Note 2) Please contact SMC for details on the maintenance intervals for this cylinder, which differs from those of the standard cylinder. Note 3) It is impossible to make the built-in magnet type and the one with auto switch. (Please contact SMC for the availability with auto switch.) Note ) Piston speed is ranged from 0 to 00 mm/s. Warning Precautions Made of Stainless Steel Specifications Parts changed to stainless steel Specifications other than above and external dimensions Same as standard product Be aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. 3 How to Order CXSJM Standard model no. Piston rod Hexagon socket head cap screw Made of stainless steel Retaining ring Hexagon socket head set screw XC Symbol XC Piston rod, Retaining ring, Hexagon socket head cap screw, Hexagon socket head set screw, Bumper bolt, Hexagon nut Same as standard product Bumper bolt Hexagon nut Note) Spring steel is used for the retaining ring on the head cover for ø. (Stainless steel is not used.) Symbol Fluoro Rubber Seals XC22 The seal material is changed to fluoro rubber that has high chemical resistance. How to Order Standard model no. XC22 Symbol 2 Low Speed Cylinder XB3 Even if driving at lower speeds of to 0 mm/s (CY: 7 to 0 mm/s), there will be no stick-slip phenomenon and it will run smoothly. How to Order Standard model no. XB3 Low speed cylinder Specifications Piston speed to 0 mm/s External dimensions Same as standard product Specifications other than above Same as standard product Note ) Operate without the lubrication of a pneumatic system lubricator. Note 2) For speed adjustment, use speed controllers at lower speeds. (Series AS-FM/AS-M) Symbol Intermediate Stroke (Spacer type) XC9 The intermediate stroke is achieved by installing a spacer within the standard stroke cylinder. How to Order Standard model no. Applicable Stroke Intermediate stroke (Spacer type) XC9 ø, 2, 3, ø0, 2, 3,, 70 ø, 2, 3,, 70, 9 ø2 ø32 Dealing with it by installing a mm width spacer within the standard stroke cylinder. Specifications other than above are the same as those for standard type. External dimensions are the same as for the standard stroke products plus adding mm to the required stroke length. Please consult SMC when a stroke other than the applicable stroke is required. Fluoro rubber seals Specifications Rod seal, Piston seal, O-ring Fluoro rubber Specifications and dimensions other than above are the same as for the standard product. 22

24 Series CXSJ Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO Note ), JIS B 370 Note 2) and other safety practices. Explanation of the Labels Labels Danger Warning Explanation of the labels In extreme conditions, there is a possible result of serious injury or loss of life. Operator error could result in serious injury or loss of life. Caution Operator error could result in injury Note 3) or equipment damage. Note ) Note ) ISO : Pneumatic fluid power General rules relating to systems Note 2) JIS B 370: General Rules for Pneumatic Equipment Note 3) Injury indicates light wounds, burns and electrical shocks that do not require hospitalization or hospital visits for long-term medical treatment. Note ) Equipment damage refers to extensive damage to the equipment and surrounding devices. Selection/Handling/Applications. The compatibility of the pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or post analysis and/or tests to meet the specific requirements. The expected performance and safety assurance are the responsibility of the person who has determined the compatibility of the system. This person should continuously review the suitability of all items specified, referring to the latest catalogue information with a view to giving due consideration to any possibility of equipment failure when configuring a system. 2. Only trained personnel should operate pneumatically operated machinery and equipment. Compressed air can be dangerous if handled incorrectly. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators. (Understanding JIS B 370 General Rules for Pneumatic Equipment, and other safety rules are included.) 3. Do not service machinery/equipment or attempt to remove components until safety is confirmed.. Inspection and maintenance of machinery/equipment should only be performed once measures to prevent falling or runaway of the driven objects have been confirmed. 2. When equipment is removed, confirm that safety process as mentioned above. Turn off the supply pressure for this equipment and exhaust all residual compressed air in the system, and release all the energy (liquid pressure, spring, condenser, gravity). 3. Before machinery/equipment is restarted, take measures to prevent quick extension of a cylinder piston rod, etc.. If the equipment will be used in the following conditions or environments, please contact SMC first and be sure to take all necessary safety precautions.. Conditions and environments beyond the given specifications, or if the product is used outdoors. 2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and brake circuits in press applications, or safety equipment. 3. An application which has the possibility of having negative effects on people, and/or property, requiring special safety analysis.. If the products are used in an interlock circuit, prepare a double interlock style circuit with a mechanical protection function for the prevention of a breakdown. And, examine the devices periodically wether they function normally or not. Exemption from Liability. SMC, its officers and employees shall be exempted from liability for any loss or damage arising out of earthquakes or fire, action by a third person, accidents, customer error with or without intention, product misuse, and any other damages caused by abnormal operating conditions. 2. SMC, its officers and employees shall be exempted from liability for any direct or indirect loss or damage, including consequential loss or damage, loss of profits, or loss of chance, claims, demands, proceedings, costs, expenses, awards, judgments and any other liability whatsoever including legal costs and expenses, which may be suffered or incurred, whether in tort (including negligence), contract, breach of statutory duty, equity or otherwise. 3. SMC is exempted from liability for any damages caused by operations not contained in the catalogues and/or instruction manuals, and operations outside of the specification range.. SMC is exempted from liability for any loss or damage whatsoever caused by malfunction of its products when combined with other devices or software. Back page

25 Series CXSJ Auto es Precautions Be sure to read this before handling. Warning. Confirm the specifications. Read the specifications carefully and use this product appropriately. The product may be damaged or malfunction if it is used out of the range of specifications of current load, voltage, temperature or impact. We do not guarantee any damage in any case the product is used out of the specification range. 2. Pay attention to the time a switch is ON at an intermediate stroke position. When an auto switch is placed at an intermediate position of the stroke and a load is driven at the time the piston passes, the auto switch will operate. However if the speed is too high, the operating time will be shortened and the load may not operate properly. The maximum detectable piston speed is: V (mm/s) = Auto switch operating range (mm) Load operating time (ms) 3. Keep wiring as short as possible. <Reed switch> In case of an auto switch with no contact protection circuit: As the length of the wiring to the load gets longer, the rush current at switching ON becomes greater, and this may shorten the product s life. (The switch will stay ON all the time.) Use a contact protection box when the wire length is m or longer. <Solid state switch> Although the wire length should not affect the switch function, use a wire 00 m or shorter. If the wiring is longer it will likely increase noise although the length is less than 00 m. When the wire is long, we recommend attaching a ferrite core to both ends of the cable to prevent excess noise.. Do not use a load that generates surge voltage. If surge voltage is generated, the discharge occurs at the contact, possibly resulting in the shortening of product life. <Reed switch> If driving a load such as a relay that generates a surge voltage, use a contact protection box. <Solid state switch> Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load such as a relay or solenoid, which generates surge, is directly driven, use a type of switch with a built-in surge absorbing element. Since the solid state auto switch is a semiconductor switch which has no contacts, no contact protection box is needed.. Cautions for using in an interlock circuit When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by using another switch (sensor) together with the auto switch. Also perform periodic maintenance and confirm proper operation.. Do not make any modifications (including exchanging the printed circuit boards) to the product. It may cause injuries to humans and damage. Design and Selection x 000 Caution. Take precautions when multiple actuators are used close together. When two or more actuators are lined up in close proximity to each other, magnetic field interference may cause the switches to malfunction. Maintain a minimum cylinder separation of 0 mm. (When the allowable interval is specified for each cylinder series, use the indicated value.) The auto switches may malfunction due to the interference from the magnetic fields. 2. Take note of the internal voltage drop of the switch. <Reed switch> ) es with an indicator light (Except D-A9, A9V) If auto switches are connected in series as shown below, take note that there will be a large voltage drop because of the internal resistance in the light emitting diodes. (Refer to internal voltage drop in the auto switch specifications.) [The voltage drop will be n times larger when n auto switches are connected.] Even though an auto switch operates normally, the load may not operate. Load In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate. Therefore, the formula below should be satisfied after confirming the minimum operating voltage of the load. Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator light (Model D- A90, A90V). <Solid state switch> 3) Generally, the internal voltage drop will be greater with a 2- wire solid state auto switch than with a reed switch. Take the same precautions as in ). For details, refer to Example of AND (serial) and OR (parallel) connection on page 7. Also, note that a 2 VDC relay is not applicable. 3. Pay attention to leakage current. <Solid state switch> With a 2-wire solid state auto switch, current (leakage current) flows to the load to operate the internal circuit even when in the OFF state. Operating current of > Leakage current load (OFF condition) If the criteria given in the above formula are not met, it will not reset correctly (stays ON). Use a 3-wire switch if this specification is not be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. Refer to page 7. Back page 2

26 Series CXSJ Auto es Precautions 2 Be sure to read this before handling. Design and Selection Caution. Ensure sufficient clearance for maintenance activities. When designing an application, be sure to allow sufficient clearance for maintenance and inspections.. Use the cylinder and switch in proper combination. The auto switch is pre-adjusted to activate properly an autoswitch-capable SMC cylinder. If the auto switch is mounted improperly, used for another brand of cylinders or used after the alternation of the machine installation, the switch may not activate properly. Mounting and Adjustment Warning. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. 2. Do not drop or bump. Do not drop, bump or apply excessive impacts (300 m s 2 or more for reed switches and 000 m s 2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause malfunction. 3. Mount switches using the proper fastening torque. When a switch is tightened beyond the range of fastening torque, the mounting screws, mounting bracket or switch may be damaged. On the other hand, tightening below the range of fastening torque may allow the switch to slip out of position. (For mounting and moving auto switches, tightening torque, etc., refer to each series.). Mount a switch at the centre of the operating range. Adjust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting position shown in the catalogue indicates the optimum position at the stroke end.) If mounted at the end of the operating range (around the borderline between ON and OFF), operation will be unstable or the service life will be shortened. <D-M9(V)> When the D-M9(V) auto switch is used to replace an old series auto switch, it may not activate depending on the operating condition because of its shorter operating range. Such as Applications in which the stop position of the actuator may vary and exceed the operating range of the auto switch, for example, pushing, pressing, clamping operation, etc. Applications in which the auto switch is used for detecting an intermediate stop position of the actuator. (In this case the detecting time will be reduced.) In these applications, set the auto switch to the centre of the required detecting range. Mounting and Adjustment Caution. Do not carry an actuator by the auto switch lead wires. Never carry a cylinder (actuator) by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 2. Fix the switch with appropriate screw installed on the switch body. If using other screws, switch may be damaged. Wiring Warning. Confirm proper insulation of wiring. Be sure that there is no faulty wiring insulation (contact with other circuits, ground fault, improper insulation between terminals, etc.). Damage may occur due to excess current flow into a switch. 2. Do not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits, including auto switches, may malfunction due to noise from these other lines. Caution. Avoid repeatedly bending or stretching lead wires. Repeated bending or tensile force applied to the lead wire may cause the sheath to fall off or disconnection of the wire. If bending or tensile force are not avoidable, fix the lead wire close to the switch and allow a bend radius of R0 to 0 mm or larger. Please consult SMC for details. Stress and tensile force applied to the connection between the cable and switch increases the possibility of the sheath to fall off or disconnection. Fix the cable in the middle so that it is not movable in the area where it connects with the switch. 2. Be sure to connect the load before power is applied. <2-wire type> If the power is turned ON when an auto switch is not connected to a load, the switch will be instantly damaged because of the excess current. It is the same case as when the 2-wire brown cord (+, output) is directly connected to the (+) power supply terminal. Back page 3

27 Series CXSJ Auto es Precautions 3 Be sure to read this before handling. Wiring Caution 3. Do not allow short circuit of the loads. <Reed switch> If the power is turned ON with a load in a short circuited condition, the switch will be instantly damaged because of thr excess current flow into the switch. <Solid state switch> Model D-M9(V), M9BA and all PNP output type switch models do not have built-in short circuit prevention circuits. If loads are short circuited, the switches will be instantly damaged, as in case of reed switches. Take special care to avoid reverse wiring of the power supply line (brown) and the output line (black) on 3-wire type switches. The 2-wire type brown lead wire is the output, and the 3-wire type lead wire with the same brown colour is the + power supply line. If the 2-wire type brown lead wire is connected to a location where the 3-wire type brown lead wire has been wired, a load short (no load) will result, causing overcurrent and damage to the switch.. Avoid incorrect wiring. <Reed switch> A 2 VDC switch with indicator light has polarity. The brown lead wire is (+) and the blue lead wire is ( ). ) If connections are reversed, the switch will operate. However, the light emitting diode will not light up. Also note that a current greater than that specified will damage a light emitting diode and it will no longer operate. Applicable models: D-A93, A93V <Solid state switch> ) If connections are reversed on a 2-wire type switch, the switch will not be damaged if protected a protection circuit, but the switch will always stay in an ON state. However, it is still necessary to avoid reversed connections, since the switch could be damaged by a load short circuit in this condition. 2) If connections are reversed (power supply line + and power supply line ) on a 3-wire type switch, the switch will be protected by a protection circuit. However, if the power supply line (+) is connected to the blue wire and the power supply line ( ) is connected to the black wire, the switch will be damaged. <D-M9(V)> The D-M9(V) does not have built-in short circuit protection circuit. Be aware if the power supply connection is reversed (e.g. (+) power supply wire and ( ) power supply wire connection is reversed), the switch will be damaged.. When the cable sheath is stripped, confirm the stripping direction. The insulator may be split or damaged depending on the direction. (D-M9(V) only) Operating Environment Warning. Never use in an atmosphere of explosive gases. The construction of auto switches is not intended to prevent explosions. Never use in an atmosphere with an explosive gas since this may cause a explosion. 2. Do not use in where a magnetic field is generated. Auto switches will malfunction or magnets inside actuators will become demagnetised. 3. Do not use in an environment where the auto switch will be in water or constantly exposed to water. Although switches satisfy IEC standard IP7 construction (JIS C 0920: waterproof construction), do not use switches in applications in which they are constantly exposed to water splash or spray. Poor insulation or swelling of the potting resin inside switches may cause malfunction.. Do not use in an environment with oil or chemicals. Please consult SMC if auto switches will be used in an environment with coolants, cleaning solvents, various oils or chemicals. If auto switches are used under these conditions for even a short time, they may be adversely affected by improper insulation, malfunction due to swelling of the potting resin or hardening of the lead wires.. Do not use in an environment with temperature cycles. Please consult SMC if the switches are going to be used where there are temperature cycles other than normal temperature changes, as they may be adversely affected internally.. Do not use in an environment where there is excessive impact shock. <Reed switch> When excessive impact (300 m/s 2 or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off the signal momentarily ( ms or less). Please consult SMC regarding the need to use a solid state switch depending on the environment. 7. Do not use in an areas where surges are generated. <Solid state switch> When there are units (solenoid type lifter, high frequency induction furnace, motor, radio equipment etc.) which generate large surges or electromagnetic waves in the area surrounding the actuators with solid state auto switches, this may cause deterioration or damage to the switches. Avoid sources of surge generation and crossed lines. Recommended Tool Model name Wire stripper Model no. D-M9N-SWY Stripper for a round cable (ø2.0) can be used for a 2-wire type cable. Back page