IMMERSION. GE Lighting. OEM Installation Guide. imagination at work. LED Display Lighting
|
|
- Hilary Small
- 5 years ago
- Views:
Transcription
1 GE Lighting OEM Installation Guide IMMESION isplay Lighting efrigerated Vertical Cases V0 Series End Mullion Lights 750 mm (0-inch): GELT0050E-SY/-S (79778/79781), GELT0050EL-SY/-S (79779/7978), GELT000E-SY/-S (7978/79787), GELT000EL-SY/-S (79785/79788) 900 mm (6-inch): GELT0650E-SY/-S (79796/79799), GELT0650EL-SY/-S (79797/79800), GELT060E-SY/-S (7980/79805), GELT060EL-SY/-S (7980/79806) escription Code (Single Unit Product Number / 10-Pack Product Number) EFOE YOU EGIN ead these instructions completely and carefully. FO YOU SFETY ead and observe all CUTIONS and NINGS shown throughout these instructions. Installation to be performed by factory trained service personnel only. For use inside a commercial refrigeration case with packaged foods only. This device complies with part 15 of the FCC ules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and () this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class digital device, pursuant to part 15 of the FCC ules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This Class [] FL complies with the Canadian standard ICES-00. Ce EF de la classe [] est conforme à la NM-00 du Canada. NING / VETISSMENT isk of electrical shock. isconnect power before servicing or installing product. / isque de choc électrique. Couper le courant avant de réparer ou installer le produit. IVE COMPTIILITY This system is compatible with the GEPS000NCMUL-SY river. Please refer to the separate driver installation guide for appropriate wiring connections. CUTION / TTENTION isk of injury. hile performing installations described, gloves, safety glasses or goggles should be worn. / isque de blessure. Lors de l'exécution des installations décrites, des gants, des lunettes de sécurité ou des lunettes de protection doivent être portées.. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.. efore servicing or cleaning unit, switch power off at the service panel and follow appropriate lock out /tag out safety procedures. PEPE ELECTICL IING Electrical equirements The power supply must be supplied with VC, 50/60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 0 ampere circuit breaker or time delay fuse. iring must be wire with ground and rated for 75 C (167 F). o not overload driver, follow installation instructions for the GEPS000NCMUL-SY. Ensure that all connection points are sealed for damp location using the appropriate method per the NEC or local electrical code. imagination at work
2 Tools equired Components equired ire stripper/cutter Tape measure Screwdriver Cordless drill Hammer.8mm (7/6-inch) drill bit Center punch 1 light driver ire cover M.5 x 1. x 1 (#6- x 1/ inch) NING/VETISSEMENT Les pièces et câbles électriques risquent d être endommagés lors du perçage 1 Prepare for Installation of End Lights Measure 8 mm (1 /-inches) from the edge of the mullion nearest the door, and mark a vertical line near the top and bottom of the frame mullion. Left End Shield 8 mm (1 /") 8 mm (1 /") ight End Shield Prepare for the upper end of the End Light. Mark a horizontal line a minimum 5 mm ( 1/8-inches) from the top of the door opening, and another horizontal line 10 mm (/8-inches) below this line. river Leads 5 mm ( 1/8") 10 mm (/8") Prepare for the lower end of the End Light. For 750 mm (0-inch) Lights, mark a horizontal line 687 mm (7 1/-inches) beneath the first line drawn for the top Mounting Tab. For 900 mm (6-inch) Lights, mark a horizontal line 86 mm ( 9/-inches) beneath the first line drawn for the top Mounting Tab. Then mark another line 10 mm (/8-inches) below this line. For 750 mm (0-inch) Lights: 687 mm (7 1/") For 900 mm (6-inch) Lights: 86 mm ( 9/") Point the center punch directly at the intersection of the horizontal lines and the vertical line (top and bottom) and establish a dimple. Use power drill and.8 mm (7/6-inches) drill bit to drill holes at the intersection of the vertical center line and the horizontal lines. epeat these steps for the mullion on the other end of the case. Center Punch at Intersection and drill a.8 mm (7/6") hole End Mullion - Left End Mullion - ight View from inside the case looking out 10 mm (/8")
3 ire ire 1 Identify End Light - ight from Left EL E Verify s are directed towards the center of the case before installing. NOTE: Installing the Light on the wrong side will result in very low light level inside the refrigerated case. View from inside the case looking out NING / VETISSMENT isk of electrical shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. o not leave any other open holes in an enclosure of wiring or electric components / isque de choc électrique. Seuls les trous ouverts indiqués dans les photos et / ou les dessins peuvent être faites ou modifiés à la suite du montage du kit. Ne pas laisser autres trous ouverts dans l'enceinte du câblage électrique ou composants. Install End Lights Place proper End Light against the face of the mullion near the two holes drilled at the top. NOTE: efer to proper End Light orientation depicted in Step 1. End Light Power Leads river Output Leads Insert a M.5 x 1. x 1 (#6- x ½-inch) sheet metal screw into the slot of the Mounting Tab on the End Light, and into the first hole that was drilled in the end mullion. Use a screwdriver to start threading the screw into the drilled hole. epeat for the second screw, and for the bottom of the End Light. efer to the manufacturing manual for door frame to ensure there are no components contained inside the mullion that could be drilled through. Use a M.5 x 1. x 1 (#6 - /-inch) self-drilling screw to attach the End Light into one or two of the additional mounting holes located near the center of the Light. Mounting Tab epeat these steps for the mullion on the other end of the case. Make sure the orientation is correct and proper Light is used. efer to wiring diagram on page 5. Connect the red and black output wires from the Light to the red and black wires on the river using the twist lock splice wire connectors provided.
4 CUTION / TTENTION isk of injury. o not overload river, 60-watts maximum per driver. For 0-inch and 6-inch Lights, do not exceed 5 Center Lights per driver loading limit. ( End Lights is equivalent to 1 Center Light). isque de blessure. Ne pas surcharger le driver, 60-watts maximum par driver. ans le cas des lampes de 0"-75 cm et de 6"/90 cm, ne pas dépasser 5 lampes centrales par limite de charge du driver. ( lampes latérales équivalent à 1 lampe centrale). 6-oor Case river Configuration Options The diagrams below represent wiring configurations for each river. IVE IVE 5-oor Case -oor Case -oor Case IVE IVE IVE -oor Case Parts Needed Per Case IVE 6-oor 5-oor -oor -oor -oor Center Lights 5 1 End Light Sets rivers ire Covers 7 6 5
5 NING / VETISSMENT isk of electrical shock. Ensure that all connection points are sealed for damp location using the appropriate method per the NEC or local electrical code. isque de choc électrique. S assurer que les points de raccordements sont scellés pour emplacement humide en employant une méthode permise par le NEC ou par le code électrique local. Connection Configurations For information on,, C,, see Steps, 5 and 6. One End Set ( & L) Lights SITCH Note: Lights are polarity insensitive Two Center Lights SITCH Note: Lights are polarity insensitive One Center Light SITCH Note: Lights are polarity insensitive IGHT EN LIGHT LEFT EN LIGHT CENTE LIGHT CENTE LIGHT CENTE LIGHT C C C IVE C LCK (LINE) HITE (NEUTL) TEMINL LOCK TEMINL LOCK HITE (NEUTL) IVE C LCK (LINE) TEMINL LOCK TEMINL LOCK IVE C HITE (NEUTL) LCK (LINE) TEMINL LOCK TEMINL LOCK One End Set (ight and Left) & One Center Light One End Light (ight or Left) & One Center Light SITCH Note: Lights are polarity insensitive SITCH Note: Lights are polarity insensitive C IVE IGHT EN LIGHT LEFT EN LIGHT CENTE LIGHT C IVE EN ( or L) LIGHT CENTE LIGHT ire Cavities (C) Cavity 1 - Line 1 (lack) Cavity - Earth Ground (Green) Cavity - Neutral or Line (hite) (C) Cavity 1 - Output C (+) (red) Cavity - Output C (-) (black) Cavity - imming (Purple) Cavity - imming (Gray) C HITE (NEUTL) LCK (LINE) TEMINL LOCK TEMINL LOCK C HITE (NEUTL) LCK (LINE) TEMINL LOCK TEMINL LOCK 5
6 Connect river - Output Make output (C) connections using one of the two options below: OPTION 1 USING -Y CONNECTO Connect the river output leads to the Light leads using the appropriate mating connector (Molex P/N ). Terminals installed should be crimped using approved tooling and process per Molex specifications. Ensure that the connector cavities are correctly populated per the wire cavity table on page 5. OPTION USING TIST-ON IE CONNECTOS emove the -way connector from the river by cutting the wires near the connector and strip the output leads. Using the appropriate wiring diagram on page 5, connect the river output leads to the Light leads using wire connectors or other connection method approved for low temperature usage and stranded cable. () 5 6 Connect river - Input Make input (C) connections using one of the two options below: The river is required to be reliably bonded to the protective ground conductor. OPTION 1 USING -Y CONNECTO ttach the supplied green/yellow ground wire from the river to a grounded metal portion of the door frame. Connect the original Line and neutral wires (or Line 1 and Line wires for 0 nominal VC) to the -way connector for the river input wires using the appropriate matingconnector (Molex P/N ). Ensure that the connector cavities are correctly populated per the wire cavity table on page 5. C Connect imming Contacts Output (Optional) For non-dimming applications, cap the unused wires with mm (5/") twist on wire connectors. OPTION USING TIST-ON IE CONNECTO ttach the supplied green/yellow ground wire from the river to a grounded metal portion of the door frame. emove the -way connector from the river by cutting the wires near the connector and strip the input wires. Using the appropriate wiring diagram on page 5, connect the original Line and neutral wires (or Line 1 and Line wires for 0 nominal VC) to the river leads using twist lock wire connectors or other connection method approved for low temperature usage and stranded cable. Ensure that the connector cavities are correctly populated per wire cavity table on page 5. C To enable dimming operation, connect leads from occupancy sensor or control system (normally open contact) to the purple and gray leads of the power supply. Make output (contact closure) connections using one of the two options below: OPTION 1 USING -Y CONNECTO Connect the river dimming output leads to the occupancy sensor or control system using the appropriate mating connector (Molex P/N ). Terminals installed should be crimped using approved tooling and process per Molex specifications. Ensure that the connector cavities are correctly populated per the wire cavity table on page 5. () OPTION USING TIST-ON IE CONNECTOS emove the -way connector from the river by cutting the wires near the connector and strip the output leads. Using the appropriate wiring diagram on page 5, connect the river dimming output leads to the occupancy sensor or control system using wire connectors or other connection method approved for low temperature usage and stranded cable. () The river is capable of step dimming from 100% power to 0% power when used with a normally open contact closure occupancy sensor system. hen using the drivers for non-dimming applications, the dip switch setting must be set to #1 ON to disable the dimming feature and achieve 100% illumination. 6
7 7 ttach Covers to End Cap Tuck wires underneath ire Cover before placing it over the End Cap and Mounting Tab. ire Cover ttach ire Cover to Light End Cap by installing a M.9x10 pan head tapping screw (provided) through the hole in the End Cap and Mounting Tab using an installation torque 0. N-m ( lbf-in). NOTE: Tighten slowly until fully seated, do not over tighten or strip the threads. epeat these steps for the mullion on the other end of the case. End Cap M.9x10 pan head tapping screw CUTION / TTENTION isk of electrical shock. Plastic cover is needed to protect electrical wires from tampering and accidental contact. / isque de choc électrique. Le couvercle en plastique est requis pour assurer une protection adéquate contre l'accès aux fils et les contacts accidentels. 8 emoval Instructions Using a phillips screwdriver, remove screw and cover from wire end of Light and screw from opposite end of Light. Electrical connections can be removed to facilitate the removal of the Light. emove the M.5 x 1. x 1 inch sheet metal screws that hold the Light to the mullion. Make sure you support the End Light with your free hand. epeat these steps for the mullion on the other end of the case. ire Cap 7
8 NING / VETISSMENT isk of electrical shock. isconnect power to Lights before any cleaning operation. isque de choc électrique. ébranchez l'alimentation des éclairages à avant toute opération de nettoyage. 9 efigerated isplay Lights Cleaning Instructions The outer lens and the plastic housing should be cleaned periodically with a mild liquid dish detergent. o not wipe the lens with a soiled dish cloth or wet towel. These may leave a residue that can damage the finish. o not use chemical cleaners to clean the lens. Keep the outside clean. ipe with a clean cloth lightly dampened with mild liquid dish detergent. ry with a clean, soft cloth. o not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and damage the finish. This product is intended solely for the use of commercial refrigerated, display or case lighting and is not intended for use in any other application. GE Lighting Solutions MY-GE GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. Immersion is a trademark of GE Lighting Solutions, LLC. The GE brand and logo are trademarks of the General Electric Company. 01 GE Lighting Solutions, LLC. Information provided is subject to change without notice. ll values are design or typical values when measured under laboratory conditions
IMMERSION. imagination at work. Retrofit Installation Guide. GE Lighting. LED Refrigerated Display Lighting
GE Lighting etrofit Installation Guide IMMESION efrigerated isplay Lighting Vertical ases V0 Series End Mullion Lights 8-inch: GELT080E-SY/-S (6603/6606), GELT080E-SY/-S (6609/6612), GELT083E-SY/-S (661/6618),
More informationIMMERSION. imagination at work. LED Refrigerated Display Lighting. Vertical Cases RV40 Series LED Drivers GEPS4000NCMUL-SY
GE Lighting Solutions Installation Guide IMMESION efrigerated isplay Lighting Vertical ases V0 Series 7981 rivers GEPS000NMUL-SY EFOE YOU EGIN ead these instructions completely and carefully. FO YOU SFETY
More informationELV1abbccd-e. Color Temperature: 30 = 3000K White 35 = 3500K White 40 = 4000K White 45 = 4500K White 50 = 5000K White
GE Lighting Immersion TM Elite LED Refrigerated Display Lighting End Mullion Lights for Vertical Cases Installation Guide ELV1abbccd-e Prefix: EL = Elite V = Vertical FD = French Door 1 = Generation Light
More informationIMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
ZR-RK Series LED Retrofit Troffer Kit Includes: ZR22RK and ZR24RK Standard and Emergency Luminaires IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION
UR Series LED Upgrade Kit Includes: 24" Linear Option IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL
More informationLumination TM LED Luminaires LAL Series - Continuous Run Option
GE Lighting Installation Guide Lumination TM LED Luminaires LAL Series - Continuous Run Option BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC
More informationTetra minimax. LED Lighting System. BEFORE YOU BEGIN Read these instructions completely and carefully. Installation Guide
Installation Guide Volt Tetra minimax LED Lighting System GEMMRD-W, GEMMGL-W, GEMMBL-W BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSMENT RISK OF ELECTRIC SHOCK Turn
More informationAlbeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)
GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these
More informationWet Rated Batten LED Luminaire
Installation Guide Wet Rated Batten LED Luminaire LED Lighting System BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING / AVERTISSEMENT RISK OF ELECTRIC SHOCK Turn power off before
More informationWARNING/AVERTISSEMENT. Coupez l alimentation électrique à la boîte de fusibles ou au disjoncteur avant servicing or installing product.
Tetra Contour LS LED Lighting System GEXNLBL-1, GEXNLGL-1, GEXNLRD-1, GEXNL65-1, GEXNL32-1 Installation Guide 24 Volt BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT
More informationINSTALLATION INSTRUCTIONS LED RETROFIT ASSEMBLY (LRA) Rev F
SAFETY S IMPORTANT SAFETY INFORMATION SUITABLE FOR DRY OR DAMP LOCATIONS. NOT FOR USE WITH PHASE CUT DIMMERS. Risk of shock. Disconnect power before installation. DANGER CONVIENT AUX EMPLACEMENTS HUMIDES.
More informationLumination TM LED Luminaire RC/LRC/RX/LRX Series - New Construction Frame
Installation Guide Lumination TM LED Luminaire RC/LRC/RX/LRX Series - New Construction Frame BEFORE YOU BEGIN Read these instructions completely and carefully. RISK OF ELECTRIC SHOCK Turn power off before
More informationHorticulture Batten LED Luminaire
GE Lighting Installation Guide Horticulture Batten LED Luminaire LED Lighting System BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK Turn
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 2.5. Suspended. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 Suspended A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5S - Safety & Warnings! 1. Read all instructions. 2.
More informationCaptivate Illuminated Mirror Light
ENGLISH WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY FRANÇAIS MISES EN GARDE ET SÉCURITÉ: SE IL VOUS PLAÎT LIRE ATTENTIVEMENT WARNING: RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRE WIRING AND ELECTRICAL
More informationInstallation Guide for EcoBrite EndLite LED Light Fixtures
Installation Guide for EcoBrite EndLite LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product.
More informationINSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa.
Oakland, INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5 LP3.5 Suspended LED A 1035 22nd Avenue, Unit 1 n CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationSpecification Grade Contemporary Wall Mount/Technical Installation Data
AVAILABLE CONFIGURATIONS RECESSED MOUNT SURFACE MOUNT MOUNTING REQUIREMENTS A. Recessed Mount: Minimum 4-Gang Box, 1-5/8 in. Deep (72.8 Cubic Inches) with 4-Gang Box Cover (20.3 Cubic Inches) B. Surface
More informationINSTALLATION INSTRUCTIONS
INDIGO-CLEAN TECHNOLOGY RETROFIT KIT INSTALLATION INSTRUCTIONS 1 IMPORTANT SAFETY INFORMATION Risk of shock. Disconnect power before installation. DANGER- RISQUE DE CHOC- COUPER L ALIMENTATION AVANT L
More informationMOONRING 1.5 MOONRING 3
INSTALLATION INSTRUCTIONS MOONRING 1.5 MOONRING 3 MR1.5 & MR3 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings!
More informationINSTALLATION INSTRUCTIONS LED Canopy Retrofit Kit
INSTALLATION INSTRUCTIONS LED Canopy Retrofit Kit TRMUNV065ECxyyZ TRAUNV065ECxyyZ Installation Instructions subject to change without notice. Page 1 of 8 1.0 INSTALLATION WARNINGS 1. 2. 3. 4. 5. 6. "THIS
More informationCable Cubby 1202 and 1402 Installation Guide
Cable Cubby 0 and 40 Installation Guide IMPORTANT: Go to www.extron.com for the complete user guide, installation instructions, and specifications. This guide provides instructions for an experienced technician
More informationLS1 SERIES IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.
The LS1 Series of commercial and industrial LED fixtures is designed to be used in utility strip applications using suspension or surface mount installation. The LS1 Series is designed for use in 120 277V,
More informationINSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1
INSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationLumination TM LED Luminaire LUR Series
Installation Guide Lumination TM LED Luminaire LUR Series BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF FIRE OR ELECTRIC SHOCK Turn power off before inspection,
More informationLUNERA VERTICAL E26 LED FLOODLIGHT LED Replacement for E26 Medium Base Floodlights Type B Ballast Bypassed
Installation Guide LUNERA VERTICAL E26 LED FLOODLIGHT LED Replacement for E26 Medium Base Floodlights Type B Ballast Bypassed Installation Description The LUNERA VERTICAL E26 LED FLOODLIGHT is a line driven
More informationGETTING STARTED WITH IN-WALL DIMMER SWITCH
GETTING STARTED WITH IN-WALL DIMMER SWITCH This document is the property of Webee L.L.C. The data contained here, in whole or in part, may not be duplicated, used or disclosed outside the recipient for
More informationLumination TM LED Luminaires Suspended LED Fixture (Series EP14)
GE Lighting Solutions Installation Guide Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) Features Long life (50,000 hour rated life) 5 year warranty IP30 Dry location rated BEFORE YOU
More informationWARNING / AVERTISSEMENT
TM Arize LED Lighting System Lynk & Life Installation Guide BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING / AVERTISSEMENT RISK OF ELECTRIC SHOCK RISQUES DE DÉCHARGES ÉLECTRIQUES
More informationLED Recessed Troffer Retrofit Kit
Model # TRK series LED Recessed Troffer Retrofit Kit Installation Instructions PACKAGE CONTENTS A B E Part Item Name Qty. A Retrofit assembly 1 B Bracket 2 C Sheet metal screw 4 D Wire nuts 5 E Gap channel
More informationpoollux Power plx-pw60 & plx-pw100
poollux Power plx-pw60 & plx-pw100 ETL LISTED Conforms to UL STD 379; Certifi.ed.to.CSA.STD.C22.2.#218.1 5005508 Installation Instructions Read all instructions before attempting to perform installation
More informationINSTALLATION GUIDE Works in double and single ended wiring.
ISTAATIO GUIDE Works in double and single ended wiring. -1- Safety Precautions For your and others safety, please read the precaution carefully before installation: (1). Product should be installed by
More informationV9961 V9961
V9961 www.fisher-price.com Please keep this instruction sheet for future reference, as it contains important information. Adult assembly required. Requires one "AAA" battery (included). Tool required for
More informationSentinel Field Satellite Controller
WARNING HIGH VOLTAGE 115V M AP Sentinel Field Satellite Controller Installation Instructions Important: For your protection and the safety of the product user, please comply with all Caution and Warning
More informationCable Cubby 650 UT Installation Guide
e NT: RTA.com for thtion O P IM tron talla w.ex uide, ins ations. o ww Go t te user g specific nd ple com ctions, a u instr Cable Cubby 650 UT Installation Guide This guide provides instructions for an
More informationP
P7639 Please keep this instruction sheet for future reference, as it contains important information. Requires four AA batteries (included) for operation. Adult assembly is required. Tool required for assembly:
More informationwww.fisher-price.com P6246 R2772 P6248 P6247 Each sold separately and subject to availability. Vehicles shown in illustrations may be different than the vehicle included with your toy. 1 Battery Installation
More informationINSTALLATION INSTRUCTION Aether 2 Shallow Recessed Housing
SAFETY INSTRUCTIONS IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance
More informationCable Cubby 1200 and 1400 Installation Guide
e NT: R.com for thtion O P IM tron talla w.ex uide, ins ations. o ww Go t te user g specific nd ple com ctions, a u instr 00 and 400 Installation Guide This guide provides instructions for an experienced
More informationPlease keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries (included) for operation. Adult assembly is required. Tool required for battery
More informationRAPID SHUTDOWN COMBINER
RAPID SHUTDOWN COMBINER Installation and Operation Guide Revision B 2017, Yaskawa Solectria Solar IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 1. General Safety Information This manual contains
More informationM9109-GGx-5 Series Proportional Electric Non-spring Return Actuators
34-636- 1360, Rev. C Installation Instructions M9109-GGx-5 Issue Date March 2016 M9109-GGx-5 Series Proportional Electric Non-spring Return Actuators Installation IMPORTANT: Use this M9109-GGx-5 Series
More informationUser s Manual. Wave to Me Magic Wand. Years. Disney. Visit DisneyJunior.com VTech Printed in China US F.P.
User s Manual Wave to Me Magic Wand Disney F.P.O Visit DisneyJunior.com 2-5 Years 2013 VTech Printed in China 91-009664-000 US INTRODUCTION Thank you for purchasing the VTech Wave to Me Magic Wand! Your
More informationOPTIMAX RADIANT FIELD RETROFIT INSTRUCTIONS
OPTIMAX RADIANT FIELD RETROFIT INSTRUCTIONS 99-24283-I001 Table of Contents 1. 24V LED Approved Drivers 5 1.1. 24V LED Driver (60-19910-0002).. 5 2. Optimax Radiant 24V LED Lighting. 6 2.1. OP30 6 2.2.
More informationLearn & Discover Driver TM
User s Manual Learn & Discover Driver TM 2012 VTech Printed in China 91-002724-000US TM INTRODUCTION Thank you for purchasing the VTech Learn & Discover Driver TM learning toy! Take a spin down the learning
More informationIMPORTANT: SAFETY INSTRUCTIONS Important: Instructions de securité
MUV-401H MultiVoltage Germicidal Air Purifier Installation & Maintenance Instructions UNPACKING THE UNIT Each MUV-401H germicidal air purifier is shipped with the germicidal lamp placed in a lamp box.
More informationAnthony LED Lighting System Retrofit Installation Instructions For Models 101X and 101A
Anthony LED Lighting System Retrofit Installation Instructions For Models 101X and 101A 99-16999-0000 Table of Contents 1. Removing Fluorescent Lighting... 4 1.1. Detach the lens assembly... 4 1.2. Remove
More informationInstallation Instructions
Installation Instructions FHEZ10A24 FHEZ17A48 Page 1 of 7 IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 1. Do not mount near gas or electric heaters. 2. Do not attempt to service the battery.
More information(SB2) (SB1) (SB3) (SB5) (SB4) Cylindrical Installation Instructions. A. CHECKLIST (4 each AA Batteries Included) (SB1) (SB4) (SB2) (SB6) (SB6) (SB3)
A. CHECKLIST (4 each AA Batteries Included) FOR DOOR AND FRAME PREPARATION INSTRUCTIONS, SEE APPENDIX A OR GO TO PROXESS.COM Parts List: Each Proxess C-Series lockset includes Exterior lock assembly (include
More informationLED FLUSHMOUNT CEILING FIXTURES
Project Source is a registered trademark of LF, LLC. ll Rights Reserved. ITEM #0806942 0806941 LED FLUSHMOUNT CEILING FIXTURES MODEL #CLL11-2BNK CLL11-2WW Français p. 9 Español p. 17 TTCH YOUR RECEIPT
More informationQuick Installation Guide. Affinium LED Modules LFM300 for Refrigerated Display Cases
Quick Installation Guide Affinium LED Modules LFM300 for Refrigerated Display Cases Important Please take the time to read this installation guide before you install the Affinium LED modules and LED power
More informationVR44-MU-xxx-8yy-xxxxA
44 UNIVERSAL INPUT LINEAR LED RETROFIT KITS Suitable for 2 x 4 luminaires Suitable for use in retrofit rebate programs Kitted for ease of Installation with provided harness Universal Voltage with 0-0V
More informationUser s Manual HORNS THE TRICERATOPS TM VTech Printed in China US
User s Manual TM HORNS THE TRICERATOPS TM 2012 VTech Printed in China 91-002679-005 US Hi Friend, You re about to embark on a dino-mite adventure with me, Horns the Triceratops! Just so you know, I ve
More informationCable Cubby 500 and 700 Installation Guide
e NT: R.com for thtion O P IM tron talla w.ex uide, ins ations. o ww Go t te user g specific nd ple com ctions, a u instr 500 and 700 Installation Guide This guide provides instructions for an experienced
More informationParent s Guide. This guide contains important information. Please keep it for future reference US
Parent s Guide This guide contains important information. Please keep it for future reference. 91-003324-000 US INTRODUCTION The Stack & Tumble Elephant TM provides a silly twist on the classic ring stacker.
More informationUNPACKING THE UNIT. Alcohol cleaning pad
MUV-403H MultiVoltage Oxidizing UVC System Installation & Maintenance Instructions UNPACKING THE UNIT Each unit is shipped with the 5 lamp installed and the germicidal lamp placed in a box with protective
More informationUser s Manual ATTILA THE ANKYLOSAURUS TM VTech Printed in China US
User s Manual ATTILA THE ANKYLOSAURUS TM TM 2012 VTech Printed in China 91-002772-000 US Hi Friend, You re about to embark on a dino-mite adventure with me, Attila the Ankylosaurus! Just so you know, I
More informationINSTALLATION INSTRUCTIONS
6400 Vehicle Dock INSTALLATION INSTRUCTIONS " " " " " " " " " " " " " " " " " " " " " " " " " " " " PN: 962-020-006 Revision B August 1998 " NOTICE The information contained herein is proprietary and is
More informationFan Relay Board (FRBii) Assembly
Fan Relay Board (FRBii) Assembly Installation, Operation, and Maintenance Instructions PK-FCU030-0, PK-FCU050-0 Part No. 24-10143-1221, Rev. A Issued February 2017 Application Refer to the QuickLIT website
More informationCHARGING FOLIO. for iphone 6 USER GUIDE
CHARGING FOLIO for iphone 6 USER GUIDE GETTING STARTED Welcome Congratulations on your recent purchase of a Case-Mate charging folio! The charging folio gives your iphone 6 up to 125% extra battery life*
More informationUser s Manual. Cruise & Learn CarTM VTech Printed in China US
User s Manual Cruise & Learn CarTM 2015 VTech Printed in China 91-002992-000 US INTRODUCTION Thank you for purchasing the VTech Cruise & Learn Car! Hop in and learn with the Cruise & Learn Car. Your child
More informationCV41. Vehicle Mounting Kit. Reference Guide
CV41 Vehicle Mounting Kit Reference Guide CV41 Vehicle Mounting Kit Reference Guide........... 3 Secure the Smart Dock to a Vehicle.................... 3 Supply Power to the Smart Dock......................
More informationX0056. fisher-price.com
X0056 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Requires three button cell (LR44) alkaline batteries (included). Batteries
More informationW3599
www.fisher-price.com W3599 Please keep this instruction sheet for future reference, as it contains important information. Requires two "AAA" batteries (included) for vehicles. Requires six "AAA" (LR03)
More informationR
R3858 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tools required for assembly: Phillips Screwdriver, Hammer and Scrap Block
More informationMAXLITE RKT LED Retrofit Kit
MAXLITE RKT LED Retrofit Kit Description and Intended Use The RKT LED Retrofit Kit is a high performance LED Fixture upgrade kit designed to replace the original components inside 2 x2 and 2 x4 fluorescent
More informationAcme Conduit Entry. String Combiner/Pass-Through. FOR PHOTOVOLTAIC INSTALLATION Installation Manual
Acme Conduit Entry String Combiner/Pass-Through FOR PHOTOVOLTAIC INSTALLATION Installation Manual Table of Contents Important Safety Instructions -----------------------------------------------------------------------------------------------------------
More informationINSTALLATION INSTRUCTIONS FOR Owner's Copy FILTERED AND REGULATED POWER SUPPLY VOLTS DC INPUT: Hz.
103158 March 9, 2011 FOR INDOOR USE ONLY Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045 (830)629-2900 / 1-800-729-3839 / Fax (830)620-6711 E-MAIL: detex@detex.com INTERNET: www.detex.com
More informationM9109 Series Electric Non-spring Return Actuators
34-636- 1190, Rev. D Installation Instructions M9109 Issue Date 03/1/16 M9109 Series Electric Non-spring Return Actuators Installation IMPORTANT: Use this M9109 Series actuator only to control equipment
More informationWASP-P PRESSURE SENSOR
WASP-P PRESSURE SENSOR USER MANUAL VERSION 03.22 15/03/2016 WASP is a registered trademark owned by BossPac Engineering & Technology WASP is a PATENT PENDING technology owned by BossPac Engineering & Technology
More informationROPE LIGHT ITEM # MODEL #UCL48L. Français p. 8. Español p. 15 ATTACH YOUR RECEIPT HERE. Purchase Date
ITEM #0879887 ROPE LIGHT MODEL #UCL48L Français p. 8 Español p. 15 TTCH YOUR RECEIPT HERE E237798 Purchase Date Questions, problems, missing parts? efore returning to your retailer, call our customer service
More informationPlease keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries for operation (included).
Please keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries for operation (included). Adult assembly is required. Tool required for battery
More informationW9740. fisher-price.com. 2 Ride. 1 Sit. 3 Walk
W9740 2 Ride 1 Sit 3 Walk Please keep this instruction sheet for future reference, as it contains important information. For ages 9 36 months and up to 44 lbs (20 kg). Adult supervision is required. Never
More informationW9740. Ride. Sit. Walk. fisher-price.com
W9740 Ride Sit Walk Please keep this instruction sheet for future reference, as it contains important information. For ages 9 36 months and up to 44 lbs (20 kg). Adult supervision is required. Never use
More informationY9854. fisher-price.com
Y9854 Please keep this instruction sheet for future reference, as it contains important information. Requires two AA (LR6) alkaline batteries for operation (not included). Adult assembly is required. Tool
More informationUser s Manual BRONCO THE RC TRICERATOPS VTech Printed in China US
User s Manual BRONCO THE RC TRICERATOPS 2014 VTech Printed in China 91-002928-006 US Hi Friend, You re about to embark on a dino-mite adventure with me, Bronco the RC Triceratops! Just so you know, I ve
More informationW
W0275 Actual product may vary from the photos. Please keep this instruction sheet for future reference, as it contains important information. Requires four "AA" (LR6) alkaline batteries (not included)
More informationPowerware Vdc Extended Battery Cabinet User s Guide.
Powerware 9125 48 Vdc Extended Battery Cabinet User s Guide www.powerware.com FCC Part 15 Class A EMC Statements NOTE This equipment has been tested and found to comply with the limits for a Class A digital
More information100A 225A 400A PATENT PENDING
HomeRun Combiner Boxes Installation and Operation Manual 100A 225A 400A PATENT PENDING TABLE OF CONTENTS 1.0 Overview 2.0 Introduction 3.0 Important Safety Instructions 4.0 Disconnecting Combiner Box Electrical
More informationSpun Bay Installation Standard Version (non dimmable), Hook Mount
Spun Bay Installation Standard Version (non dimmable), Hook Mount WARNING: Make sure that all power is turned off while installing fixture. Do not turn power on until fixture is completely installed. Turn
More informationPress the buttons for fun sounds and music! fisher-price.com
K7189 Press the buttons for fun sounds and music! fisher-price.com Please keep these instructions for future reference, as they contain important information. Requires three button cell (LR44) batteries
More informationUser s Manual VTech Printed In China US CA Manual new.indd /6/6 10:41:57
User s Manual 2013 VTech Printed In China 91-002805-014 US CA 6700-201 Manual new.indd 1 2013/6/6 10:41:57 Dear Parent, Smart Wheels fun as well. Go! Go! Smart Wheels Go! Go! Go! Go! Smart Wheels features
More informationInstallation Instructions RF4510-EA
Installation Instructions RF4510-EA HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 1 Product Description Dimensions Orientation Compatibility Access Control Systems Proximity Cards Frequency
More informationINSTALLATION INSTRUCTION Aether 3.5 Color Tunable LED Downlight
SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance
More informationOptimax Pro Retrofit Instructions
Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in examples herein are fictitious unless otherwise noted. No part
More informationSystem 350 S350C Temperature Slave Stage Module
FANs 930, 930.5, 125, 121 Product/Technical Bulletin Issue Date April 8, 2014 System 350 Temperature Slave Stage Module The Temperature Slave Stage Module is used in conjunction with the A350 Temperature
More informationParent s Guide Mickey Ramps Fun House
Parent s Guide Mickey Ramps Fun House Disney www.disney.com 91-003532-000 INTRODUCTION Thank you for purchasing the VTech Go! Go! Smart Wheels Mickey Ramps Fun House! Little racers can rearrange the tracks
More informationTM-11x1 Series Room Temperature Module
24-10225- 4, Rev. C TM-11x1 Series Installation Instructions Part No. 24-10225-4, Rev. C Issued March 16 Applications The TM-11x1 Series of s are designed for use with the TC-9102 Direct Digital Control
More informationCONTENTS DESCRIPTION UNPACKING DIMENSIONS
INSTALLATION INSTRUCTIONS Recessed Luminaire ModelNo.FV-NLF6RES CONTENTS GENERAL SAFETY INFORMATION DESCRIPTION UNPACKING SUPPLIED ACCESSORIES DIMENSIONS WIRING DIAGRAM INSTALLATION (BETWEEN JOISTS MOUNTING)
More informationX2916. fisher-price.com WARNING. Overhead Gym. Tummy Time Fun
X2916 Overhead Gym Tummy Time Fun WARNING To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym. Please keep this instruction sheet
More informationBear s Baby Laptop TM
User s Manual Bear s Baby Laptop TM 2013 VTech Printed in China 91-002821-000US INTRODUCTION Thank you for purchasing the VTech Bear s Baby Laptop TM learning toy! Bear s Baby Laptop TM encourages little
More informationT
T4262 Please keep this instruction sheet for future reference, as it contains important information. Maximum weight: 44 lbs. (20 kg). For ages between 9 months and 3 years. Requires three AA batteries
More informationParent s Guide. Touch & Discover Sensory Turtle
Parent s Guide Touch & Discover Sensory Turtle 91-003520-000 INTRODUCTION Thank you for purchasing the VTech Touch & Discover Sensory Turtle. This cute plush toy converts from a turtle to a ball. The large
More informationP Volt Charger Each sold separately and subject to availability.
P6828 6-Volt 4 Amp/Hr Battery P6829 6-Volt Charger Each sold separately and subject to availability. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS. For use with a Power Wheels toddler vehicle
More informationPRODUCT DESCRIPTION SPECIFICATIONS
PRODUCT DESCRIPTION The Ranco ETC is a microprocessor based electronic temperature control designed to provide on/off control for commercial heating, ventilating, air conditioning and refrigeration. The
More informationBFK51 CFD40 CHM41. fisher-price.com
BFK51 CFD40 CHM41 Please keep this instruction sheet for future reference, as it contains important information. Requires three AA (LR6) alkaline batteries (not included). Adult assembly is required. Tool
More informationT Overhead Gym. Tummy Time Fun. On-the-Go Fun
T6339 Please keep this instruction sheet for future reference, as it contains important information. Requires four AA (LR6) alkaline batteries for operation (not included). Tool required for battery installation:
More informationOSQ Series IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. LED Area Light TO INSTALL:
OSQ Series LED Area Light Direct Pole Mount IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY
More informationWARNING. To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym.
X7299 WARNING To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym. Please keep this instruction sheet for future reference, as it
More informationEnclosure for AMP1 Series Energy Meters with Swing Panel Kit
GE Industrial Solutions DET-809 Installation Instructions AMP1N4 Enclosure for AMP1 Series Energy Meters with Swing Panel Kit Safety FCC PART 15 INFORMATION NOTE: This equipment has been tested by the
More information