Investigation of Diffuser Concept for Four Strokes C.I. Engine Exhaust System Development

Size: px
Start display at page:

Download "Investigation of Diffuser Concept for Four Strokes C.I. Engine Exhaust System Development"

Transcription

1 Investigation of Diffuser Concept for Four Strokes C.I. Engine Exhaust System Development #1 Gaurav Tiwari, #2 Riyaz Kazi #1 PG Student,Heat Power Engg.,MCOERC,Nashik, SPPU,India #2 Asst. Professor, Head of Mechanical Department, MCOERC, Nashik, SPPU, India Abstract The global warming and air pollution are big issue now a days in the world. The major part of air pollution is due to emissions from an internal combustion engine. Exhaust system plays a vital role in reducing harmful gases, but the presence of after treatment systems increases the exhaust back pressure. To minimize the exhaust emissions from C.I. engines, it is very important to study the overall effects of Devices attached in the exhaust system. Back pressure on engine is found as an important parameter having a strong influence on engine efficiency and it need to be minimized for maximum fuel efficiency. This work deals with the investigation of exhaust system through experimentation and CFD (Fluent), a compromise between two parameters namely, increase in brake thermal efficiency with limited back pressure was aimed at. In experimental analysis, different convergent divergent exhaust diffuser system (EDS) models with different angels are analyzed. The back pressure variations in six models and the flow of the gas in the substrate are discussed. Finally, the performance of the engine and the exhaust diffuser systems are discussed. Keywords: Exhaust Diffuser system (EDS), Computational Fluid Dynamics (CFD), Backpressure, Fuel Consumption I. INTRODUCTION To get less fuel consumption energy efficient exhaust system development is required and to reduce the exhaust emissions maximum utilization of exhaust energy is to be required and also for effective waste energy recovery system such as in turbocharger, heat pipe etc. from C.I. engine. To analyze the exhaust energies obtainable at different engine operating conditions then to improve an exhaust system for maximum utilization of available energy at the exhaust of engine cylinder is studied. After the end of power stroke and the exhaust stroke starts when the piston changes from bottom Dead Centre to top Dead Centre, pressure increases and the engine performance should not be affected poorly for this purpose the design of every device shall have least pressure drop through the device gases are pressed into exhaust pipe. Therefore the power essential to drive exhaust gases is called exhaust stroke loss and rise in speed increases the exhaust stroke loss. The total work output per cycle from the engine is reliant on the pumping work spent, which is directly relative to the backpressure. To reduce the pumping work, backpressure must be as minimum as possible. The back-pressure is directly related to the exhaust diffuser system design. The profile of the inlet cone of exhaust diffuser system contributes the backpressure. This increment in backpressure causes rise in fuel consumption. Actually, an amplified pressure drop is a very key challenge to overwhelmed (Heywood, 1988), (Silvers et al, 1991).This work treat with the study of flow of an exhaust diffuser system. Computational fluid study is carried to conclude the pressure profile. Computational fluid study is done using two software CATIA V5 and ICEM CFD are used to prepare the model and mesh it and ANSYS FLUENT 14.5 is used to do the velocity, temperature and pressure analysis. This total investigation is called as Computational fluid dynamics analysis. Before carrying out the analysis it is vital to have an outline of what fluent is and how it works (Navale et al, 2014) II. LITERATURE REVIEW Since last 3 to 4 decades after treatment techniques are being increasingly utilized and research work is well under progress. Effective after treatment system, specifically for I.C. engines, requires critical analysis of the overall effect of backpressure on each particular I.C. engine performance. More efforts are required for the analysis of the after treatment System, by further study of the theory of operation of each device related to I.C. engines. Search on diesel particulate filters as a modern technology is very active because particulate matter is designated as a major cancer material. Regeneration phenomenon in after treatment devices is a subject of special concern for design and development of particulate matter emission control actions. The Backpressure acting on engine is most significant factor which mostly depreciates the engine and emission control performance. In the present work, dimensional analysis method is used for finding out the relationship between operating variables of internal combustion engines, then validation of the effect of back-pressure generated on a C.I. engine, with and without the usage of a particularly designed diesel particulate filter is done (Modak et al, 2010). To offer an estimation of the potential effect of substrate and exhaust system backpressure on engine performance is the objective of this work. Factors contain fuel consumption, CO 2 emissions, and HP. Results were gained on an engine test standpoint, and then statistical analysis was used to know the relations between variables. 2015, IERJ All Rights Reserved Page 1

2 Trade-offs among catalyst substrate selection and engine performance for the particular engine used in this study are labeled. Lastly, the potential impact of exhaust system backpressure on actual world driving situations is deliberated (Jonathan et al, 2009). To find out the optimum geometry for decreasing emissions work is done on CFD analysis of exhaust manifold of multicylinder S.I. engine, The most critical components of an I.C. engine is exhaust manifold. The designing of exhaust manifold is a complex process and is reliant on various parameters viz. back pressure, exhaust velocity, mechanical efficiency etc. Liking for any of this parameter varies as per designer s desires. Generally fuel economy, emissions and power requirement are three separate thought about exhaust manifold design. The study widely analyses 8 separate models of exhaust manifold and then determines the best likely design for minimum emissions and complete combustion of fuel to ensure least pollution (Rajagopal et al, 2013).It is well known that a accurately designed intake manifold is important for the optimal performance of an I.C. engine. This work will present 3-D simulation of a 1.6L MPFI engine intake manifold by using the FLUENT code and the results will be talk over. Both steady and unsteady state simulations have been consummate for this case. For validation steady state simulation results are compared with flow bench rig data. From 1-D WAVE code boundary condition for unsteady state simulation was found. Lastly according to the results of steady and unsteady simulations, some ideas are recommended to advance the performance of this intake manifold (Nasirtosi et al,2003).during the investigation on optimization of exhaust systems, the abstract is given here. Some design optimization work of automotive exhaust systems are taken out using numerical simulation. This numerical simulation includes computational fluid dynamics for fluid flow and temperature distribution and finite element analysis (FEA) for following structural analysis. The importance is given to optimization associated to exhaust system design parameters such as shape and shape of manifold, catalyst inlet tube, inlet cone, exit cone, and exit tube under a given exhaust gas conditions. Numerous cases of optimization including study of design parameters on the index of flow evenness and backpressure are explained. Another part of this study includes finite element calculation of stresses and strains. In structural analysis due to high temperatures involved in the exhaust system both material and geometric non-linearity are measured. Precisely, the work involves the calculation of material response behavior under numerous thermal cycles, every cycle involving a heating and a cooling stages, and finally comparative study of suitability of cast steel and fabricated steel for exhaust manifolds are debated (Keck Et al, 2002).During the investigation in the result of intake manifold runners length on the volumetric efficiency by 3D CFD Model, the abstract is given here. It is quite known that a correctly designed intake manifold is important for the optimal performance of an I.C. engine. 3-D Simulation of a XU7 engine intake manifold is to be studied in present work and the results will be debated. Boundary condition for unsteady state simulation was gained. From 1-D WAVE code With the help of 3D CFD models at separate speeds are analyzed in the current investigation of the effect of length of runners on the volumetric efficiency.three hypothetical models have been prepared that all of their runner s length is increased to 110,120 and 130% of initial value. In the model with 20% extended runners, the volumetric efficiency rises at 3500 rpm and 4500 rpm. Lastly according to the results of steady and unsteady simulations, some suggestions are suggested to progress the performance of this intake manifold (Negin et al,2006) III. METHODOLOGY The study has been done out on six designs a current one that is EDS I with 0 inlet cone angle besides a improved one that is EDS VI by 90 inlet cone angle, outcomes are afterward compared. It was observed that the brake thermal efficiency enriched drastically upon modification in exhaust geometry. Physical models of the similar these two systems are afterward manufactured and exhaustive experiments are done on them. The outcomes gained through CFD analysis are experimentally checked. For analyzing its performance using CFD the Exhaust system data for the same engine output condition that is at 0.5 to 5 kg load at ten levels and 1500 rpm is given. The EDSEDS I to EDS VI are developed.the major objective of analyzing such a systems are to determine the pressure drop across the exhaust diffuser system geometry using experimentation and CFD analysis. 3.1 Construction of the Model The coordinates are shown for the development of the 2D model of the exhaust system. Then the model is rotated about 360⁰ to get the 3D profile. The diffuser can be seen as an assembly of three distinct sections operating in series a short parallel section and the diverging section for design solution. The short parallel section of the system to the engine acts as a casing. To reduce the non-uniformity of flow the straight portion of the diffuser helps and the pressure recovery takes place in the diverging section. The geometrical specifications of the diffuser have selected somewhat arbitrarily. Diameter of diffuser inlet is m and diameter of the engine outlet is 0.15m. The model of exhaust diffuser system is shown in Fig.1 Fig.1 Model of Exhaust Diffuser System-III Then all the parts are well-defined i.e. inlet is defined as Inflow, outlets as Outflow, and wall. 2015, IERJ All Rights Reserved Page 2

3 IV. THREE DIMENSIONAL CFD STUDY A 3D model of exhaust diffuser system is made in CFD Fluent for the study. 4.1 Modeling and Meshing The meshing used for geometry of the element is made as tetrahedral mesh, with an advanced mesh near the wall. With standard wall functions for near-wall treatment for analysis of Exhaust system the K-E turbulence model is used. 4.2 Boundary Conditions Boundary conditions used are applied at inlets mass flow rates and temperatures of fluid and at outlets pressure outlet is applied. Domain surface is used as a wall with No Slip condition and heat transfer coefficient of 45 w/m2⁰k and wall surface roughness as 5.08 micron is used (Anderson, 1995). V. CFD RESULTS & DISCUSSION The main aim of this CFD analysis is to invent out the correct form of system for the exhaust system which can offer least backpressure [6]. Fig.2 Shows the Pressure Contour which indicates the change of Pressure along the X- Axis for EDS III at Continuous Load of 5 Kg. Fig.3 Shows that variation in backpressure on engine during the flow through EDS III along its length at Constant Load 5 Kg It is seen that the back pressure at inlet of EDS- III is found to be Pa, as shown in Fig.2 and In Fig.3 the back pressure is found to be rise with the increase in length of EDS for the similar inlet pressure. Likewise the back pressure study is done for further EDS. The back pressure is found to be reducing with the rise in inlet cone angle of EDS for the similar inlet pressure (Navale, 2014). VI. EXPERIMENTAL RESULT & DISCUSSION The experimentation was conducted with the six diffuser systems in single cylinder four stroke diesel engines. On the engine exhaust flange the exhaust system was fitted. Then the performance study was conducted and Figs are plotted against the brake thermal efficiency. 2015, IERJ All Rights Reserved Page 3

4 Fig.4 Schematic view of experimental set up 1 Fuel Flow Measurement 2 U- Tube Manometers 3 Dynamometer 4 Air Flow Meter 5 C.I. Engine 6 Exhaust Gas Calorimeter 7 Exhaust System X-X: Inlet to Exhaust Diffuser System Y-Y: Inlet to Exhaust Diffuser System. All dimensions are in cm Fig.5 Schematic view of exhaust diffuser system It is observed from the Fig.6 variations in brake thermal efficiency vs. backpressure on engine for different load conditions using EDS. It is found that when the load is kept constant load at different level viz. 0.5 kg to 5 kg the backpressure on engine reduces, brake thermal efficiency rises. The backpressure on engine reduces and brake thermal efficiency rises, because of rise in the brake power for EDS I to EDS VI. During the change of EDS I to EDS VI the rise in the brake thermal efficiency from 9 to 14% is observed by keeping all other parameters constant. The value of brake thermal efficiency and backpressure for EDS I is rising, as load is increasing. 2015, IERJ All Rights Reserved Page 4

5 Fig.6 Brake thermal efficiencies vs. backpressure on engine Fig.7 Heat carried by exhaust gases vs. backpressure on engine It is observed from the Fig.7, variation in heat carried by exhaust gases verses back-pressure on engine for different load conditions using EDS shows that when the load is kept constant at separate level viz. 0.5 to 5 kg the backpressure on engine reduces and heat carried away by exhaust gases decreases. It is also observed that during the change of EDS I to EDS VI backpressure on engine reduce and heat carried away by exhaust gases also reduces. Heat carried away by exhaust gases cuts approximately 4 percentages for EDS VI system as compared to EDS I. Value for heat carried away by exhaust gases for EDS I is reducing, as load is rising. It is observed from the Fig.8, heat balance sheet for different EDS at constant load 5 kilogram; the heat balance sheet parameters that are heat equivalent of brake power, heat carried by the jacket cooling water, heat carried by exhaust gases and heat unaccounted for. When the EDS are varies during the change from EDS - I to EDS - VI the heat equivalent of brake power increases and heat carried by exhaust gases reduces. After testing it is observed that around 30 to 40 % of fuel energy is wasted, this part is of great concerned so as to maximize consumption of exhaust energy. Fig.8 Heat balance sheet at constant load 5 Kg It is important to utilize the exhaust energy through proper exhaust system design. Optimum energy utilization means that the fuel energy which is otherwise going to be wasted must be utilized in such a manner that it must not affect the engine performance adversely, which basically occurs because of increase in back pressure on the engine. The variation in the exhaust energy carried away by exhaust gases is found to be directly proportional to backpressure on the engine. 2015, IERJ All Rights Reserved Page 5

6 Fig.9 Back-pressure on engine by experimentation vs. different load conditions As observed from the Fig.9 variation back-pressure on engine using values observed during experimentation verses different load conditions with EDS; when the load is kept constant load at separate levels viz. 0.5 to 5 kg the backpressure on engine reduces. It is also found that when the exhaust diffuser system is varied during the change of EDS I to EDS VI backpressure on engine reduces. Backpressure on engine reduces which results raise in brake power of engine. Value for backpressure on engine for EDS I is rising, as load is increasing. The back pressure is found to be increased with the decrease in length of taper for the same inlet conditions. It is observed from the Fig 10 variation of backpressure on engine using CFD Fluent analysis vs. different load conditions with EDS, when the load is kept constant at different level viz. 0.5 to 5 kg the backpressure on engine reduces. It is also found that when the exhaust diffuser system is varied during the change of EDS I to EDS VI, backpressure on engine reduces. Value for backpressure on engine for EDS I is increasing, as load is increasing Fig.10 Back-pressure on engine by means of CFD vs. different load conditions. By means of observed from the Fig.11, pressure difference using EDS. It is found that during the change of EDS I to EDS VI pressure difference using exhaust systems on engine increases. The load on engine is varied at different level viz.0.5 kg to 5 kg, the pressure difference using exhaust systems on engine increases for EDS I to EDS VI. At EDS I i.e. inlet cone angle 0 the volume is m3 and EDS VII i.e. inlet cone angle 90 the volume is m3. Change in volume because of diffuser angle change is the basic cause of reduction in backpressure on engine. Fig.11 Load range vs. Pressure difference VII. CONCLUSIONS The following conclusions is be drained from the present study. The Exhaust system is effectively designed using diffuser concept. By CFD analysis using ANSYS FLUENT 14.5, the backpressures of EDS are learned. The decrease in inlet cone angle increases the velocity of the flow which leads to increase circulation at after treatment section. The increase in outlet cone angle of diffuser raises the pressure of the flow which leads to reduce the recirculation zones. Installation of the EDS VI increases the brake thermal efficiency and decreases the backpressure. 2015, IERJ All Rights Reserved Page 6

7 REFERENCES 1. J.B.Heywood,(1988),Internal Combustion Engine Fundamentals,McGraw Hill, ISBN R.G. Silver,J. C. Summers and W. B. Williamson,(1991), Design and Performance Evaluation of Automotive Emission Control Catalysts, Envier Science Publishers B. V. Amsterdam. 2. Desmond E Winter Bone & Richard J Pearson,(2000), Theory of Engine Manifold Design, Professional Engineering Publishing. 3. G.Venkatesh,(2006),Power Production Technique Using Exhaust Gas From Present Automobiles via Convergent-Divergent Nozzle, /06 IEEE. 4. John D. Anderson, Jr., (1995), Computational Fluid Dynamics - The Basic with Applications, McGraw - Hill International Editions. 5. Meda Lakshmikantha & Mathias Keck,(2013), Optimization of Exhaust Systems, SAE Paper No , Atul A. Patil, Dr. L. G. Navale, Dr. V. S. Patil, Simulative Analysis of Single Cylinder Four Stroke C.I. Engine Exhaust System, Pratibha International Journal of science, Spirituality, Business and Technology (IJSSBT), Vol. 3, ISSN (print) , D.S.Deshmukh, J.P.Modak and K.M. Nayak,(2010), Experimental Analysis of Backpressure Phenomenon Consideration for C.I. Engine Performance Improvement, SAE Paper No , International Powertrains, Fuels & Lubricants Meeting, Rio De Janeiro, Brazil, on dated A.A. Patil, D.S. Deshmukh, L.G. Navale and V.S. Patil,(2011), Experimental Investigation of a C.I. Engine Operating Parameters For Energy Efficient Exhaust System Development, International Journal of Innovations In Mechanical & Automobile Engineering (IJIMAE), ISSN (Print), Issue I, Vol. -II, Atul A. Patil, L. G. Navale, V. S. Patil, (2014), Experimental Investigation and Analysis of Single Cylinder Four Stroke C. I. Engine Exhaust System, International Journal of Energy and Power (IJEP) Volume 3 Issue, Atul A. Patil, L. G. Navale and V. S. Patil,(2014), Design, Analysis of Flow Characteristics of Exhaust System and Effect of Back Pressure on Engine Performance, International Journal of Engineering, Business and Enterprise Applications (IJEBEA)14-165, ISSN (Print): , ISSN (Online): , D.S. Deshmukh, M.S. Deshmukh and J.P. Modak,Experimental Investigation of the Effect of Backpressure on an I.C. Engine Operating Performance, International Journal of Emerging Technologies and Applications in Engineering, Technology and Sciences, ISSN: , 1 April 2010, pp Jonathan D. Pesansky, Nathan A. Majiros, The effect of three-way catalyst section on component pressure drop and system performance, SAE Paper NO K. S. Umesh, V. K. Pravin& K. Rajagopal,CFD Analysis of Exhaust Manifold of Multi-Cylinder SI Engine to Determine Optimal Geometry for Reducing Emissions, International Journal of Automobile Engineering Research and Development, ISSN Vol. 3, Issue 4, Oct 2013, pp M. Safari & M. Ghamari, A. Nasirtosi,Intake Manifold Optimization by using 3-D CFD Analysis, SAE Paper No MedaLakshmikantha& Mathias Keck, Optimization of Exhaust Systems, SAE Paper No NeginMoffouni& Reza Ebrahimi, SiamacHossein Pour,The effect of Intake Manifold Runners Length on the volumetric Efficiency by 3D CFD Model, SAE Paper No, , IERJ All Rights Reserved Page 7

Experimental Verification and CFD Analysis of Single Cylinder Four Strokes C.I. Engine Exhaust System

Experimental Verification and CFD Analysis of Single Cylinder Four Strokes C.I. Engine Exhaust System Experimental Verification and CFD Analysis of Single Cylinder Four Strokes C.I. Engine Exhaust System Atul A. Patil 1,L.G. Navale 2,V.S. Patil 3 1 (Research student, North Maharashtra University, Umavi

More information

DESIGN OF EXHAUST MANIFOLD TO IMPROVE PERFORMANCE OF IC ENGINE- A REVIEW

DESIGN OF EXHAUST MANIFOLD TO IMPROVE PERFORMANCE OF IC ENGINE- A REVIEW International Journal of Recent Innovation in Engineering and Research Scientific Journal Impact Factor - 3.605 by SJIF e- ISSN: 2456 2084 DESIGN OF EXHAUST MANIFOLD TO IMPROVE PERFORMANCE OF IC ENGINE-

More information

CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump

CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump ISSN 2395-1621 CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump #1 SuhasThorat, #2 AnandBapat, #3 A. B. Kanase-Patil 1 suhas31190@gmail.com 2 dkolben11@gmail.com 3 abkanasepatil.scoe@sinhgadedu.in

More information

CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate

CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate Sandeep M, U Sathishkumar Abstract In this paper, a study of different cross section bundle arrangements

More information

Experimental and CFD Analysis of Exhaust Manifold to Improve Performance of IC Engine

Experimental and CFD Analysis of Exhaust Manifold to Improve Performance of IC Engine International Research Journal of Engineering and Technology (IRJET e-issn: 2395-56 Experimental and CFD Analysis of Exhaust Manifold to Improve Performance of IC Engine Mr. SACHIN G. CHAUDHARI 1, Mr.

More information

Chapter 7: Thermal Study of Transmission Gearbox

Chapter 7: Thermal Study of Transmission Gearbox Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational

More information

CONJUGATE HEAT TRANSFER ANALYSIS OF HELICAL COIL HEAT EXCHANGE USING CFD

CONJUGATE HEAT TRANSFER ANALYSIS OF HELICAL COIL HEAT EXCHANGE USING CFD CONJUGATE HEAT TRANSFER ANALYSIS OF HELICAL COIL HEAT EXCHANGE USING CFD Rudragouda R Patil 1, V Santosh Kumar 2, R Harish 3, Santosh S Ghorpade 4 1,3,4 Assistant Professor, Mechanical Department, Jayamukhi

More information

CFD Analysis and Comparison of Fluid Flow Through A Single Hole And Multi Hole Orifice Plate

CFD Analysis and Comparison of Fluid Flow Through A Single Hole And Multi Hole Orifice Plate CFD Analysis and Comparison of Fluid Flow Through A Single Hole And Multi Hole Orifice Plate Malatesh Barki. 1, Ganesha T. 2, Dr. M. C. Math³ 1, 2, 3, Department of Thermal Power Engineering 1, 2, 3 VTU

More information

Back pressure analysis of an engine muffler using cfd and experimental validation

Back pressure analysis of an engine muffler using cfd and experimental validation Back pressure analysis of an engine muffler using cfd and experimental validation #1 Mr. S.S. Mane, #2 S.Y.Bhosale #1 Mechanical Engineering, PES s Modern College of engineering, Pune, INDIA #2 Mechanical

More information

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine Available online atwww.scholarsresearchlibrary.com Archives of Applied Science Research, 2016, 8 (7):31-40 (http://scholarsresearchlibrary.com/archive.html) ISSN 0975-508X CODEN (USA) AASRC9 Comparison

More information

ABSTRACT I. INTRODUCTION III. GEOMETRIC MODELING II. LITERATURE REVIW

ABSTRACT I. INTRODUCTION III. GEOMETRIC MODELING II. LITERATURE REVIW 2017 IJSRSET Volume 3 Issue 5 Print ISSN: 2395-1990 Online ISSN : 2394-4099 Themed Section: Engineering and Technology Performance Analysis of Helical Coil Heat Exchanger Using Numerical Technique Abhishek

More information

Thermal Stress Analysis of Diesel Engine Piston

Thermal Stress Analysis of Diesel Engine Piston International Conference on Challenges and Opportunities in Mechanical Engineering, Industrial Engineering and Management Studies 576 Thermal Stress Analysis of Diesel Engine Piston B.R. Ramesh and Kishan

More information

Design and Development Of Opposite Piston Engine

Design and Development Of Opposite Piston Engine ISSN (Online) : 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology Volume 3, Special Issue 3, March 2014 2014 IEEE International Conference

More information

Analysis of Exhaust System using AcuSolve

Analysis of Exhaust System using AcuSolve Analysis of Exhaust System using AcuSolve Abbreviations: CFD (Computational Fluid Dynamics), EBP (Exhaust Back Pressure), RANS (Reynolds Averaged Navier Stokes), Spalart Allmaras (SA), UI (Uniformity Index)

More information

INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE

INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE 1. UNIVERSITY OF RUSE, 8, STUDENTSKA STR., 7017 RUSE, BULGARIA 1. Simeon ILIEV ABSTRACT: The objective of this paper is to

More information

DESIGN OF THROTTLE BODY: A COMPARATIVE STUDY OF DIFFERENT SHAFT PROFILES USING CFD ANALYSIS

DESIGN OF THROTTLE BODY: A COMPARATIVE STUDY OF DIFFERENT SHAFT PROFILES USING CFD ANALYSIS Int. J. Chem. Sci.: 14(S2), 2016, 681-686 ISSN 0972-768X www.sadgurupublications.com DESIGN OF TROTTLE BODY: A COMARATIVE STUDY OF DIFFERENT SAFT ROFILES USING CFD ANALYSIS M. BALAJI *, K. AMAL SATEES,

More information

INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING

INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING Journal of KONES Powertrain and Transport, Vol. 7, No. 4 200 INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING Emil Toporcer, Peter Tunik University of Žilina, Faculty of Mechanical Engineering Department

More information

CFD ANALYSIS ON LOUVERED FIN

CFD ANALYSIS ON LOUVERED FIN CFD ANALYSIS ON LOUVERED FIN P.Prasad 1, L.S.V Prasad 2 1Student, M. Tech Thermal Engineering, Andhra University, Visakhapatnam, India 2Professor, Dept. of Mechanical Engineering, Andhra University, Visakhapatnam,

More information

DESIGN OF A NEW IMPROVED INTAKE MANIFOLD FOR F-SAE CAR Abhishek Raj 1, J.C. Mohanta 2, Bireswar Paul 3, Mohd. Nayab Zafar 4 1

DESIGN OF A NEW IMPROVED INTAKE MANIFOLD FOR F-SAE CAR Abhishek Raj 1, J.C. Mohanta 2, Bireswar Paul 3, Mohd. Nayab Zafar 4 1 DESIGN OF A NEW IMPROVED INTAKE MANIFOLD FOR F-SAE CAR Abhishek Raj 1, J.C. Mohanta 2, Bireswar Paul 3, Mohd. Nayab Zafar 4 1 pg Scholar, 2 assistant Professor, 3 assistant Professor, 4 research Scholar

More information

Designing & Validating a New Intake Manifold for a Formula SAE Car

Designing & Validating a New Intake Manifold for a Formula SAE Car Designing & Validating a New Intake Manifold for a Formula SAE Car Arpit Singhal 1 1 (M.Tech (Computational Fluid Dynamics) University of Petroleum &Energy Studies, India Abstract This paper gives the

More information

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4

More information

IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 07, 2016 ISSN (online):

IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 07, 2016 ISSN (online): IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 07, 2016 ISSN (online): 2321-0613 Design, Optimization and Analysis of Exhaust Muffler to Reduce Exhaust Noise Level and

More information

e t Performance of Extended Inlet and Extended Outlet Tube on Single Expansion Chamber for Noise Reduction

e t Performance of Extended Inlet and Extended Outlet Tube on Single Expansion Chamber for Noise Reduction e t International Journal on Emerging Technologies 7(1): 37-41(2016) ISSN No. (Print) : 0975-8364 ISSN No. (Online) : 2249-3255 Performance of Extended Inlet and Extended Outlet Tube on Single Expansion

More information

Manufacturing Elements affecting the Performance & Durability Characteristics of Catalytic Converter

Manufacturing Elements affecting the Performance & Durability Characteristics of Catalytic Converter Manufacturing Elements affecting the Performance & Durability Characteristics of Catalytic Converter Mylaudy Dr.S.Rajadurai 1, R.Somasundaram 2, P.Madhusudhanan 2, Alrin M Victor 2, J.Y. Raja Shangaravel

More information

Effect of Helix Parameter Modification on Flow Characteristics of CIDI Diesel Engine Helical Intake Port

Effect of Helix Parameter Modification on Flow Characteristics of CIDI Diesel Engine Helical Intake Port Effect of Helix Parameter Modification on Flow Characteristics of CIDI Diesel Engine Helical Intake Port Kunjan Sanadhya, N. P. Gokhale, B.S. Deshmukh, M.N. Kumar, D.B. Hulwan Kirloskar Oil Engines Ltd.,

More information

PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE

PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE V. S. Konnur Department of Mechanical Engineering, BLDEA s Engineering College, Bijapur, Karnataka, (India) ABSTRACT The automotive

More information

Research in hydraulic brake components and operational factors influencing the hysteresis losses

Research in hydraulic brake components and operational factors influencing the hysteresis losses Research in hydraulic brake components and operational factors influencing the hysteresis losses Shreyash Balapure, Shashank James, Prof.Abhijit Getem ¹Student, B.E. Mechanical, GHRCE Nagpur, India, ¹Student,

More information

[Rohith, 5(1): January, 2016] ISSN: (I2OR), Publication Impact Factor: 3.785

[Rohith, 5(1): January, 2016] ISSN: (I2OR), Publication Impact Factor: 3.785 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY COMPARING DIFFERENT VALVE LIFTS IN AN IC ENGINE USING COLD FLOW SIMULATION Rohith S, Dr G V Naveen Prakash Mechanical Engineering,

More information

CFD Flow Analysis and Optimization of Exhaust Muffler

CFD Flow Analysis and Optimization of Exhaust Muffler CFD Flow Analysis and Optimization of Exhaust Muffler Saumil Mahesh Trivedi 1, Sangita Bansode 2, Pankaj Pawar 3 1 Mtech CAD-CAM & Robotics Student Somaiya college of engineering 2 Professor, Department

More information

ANALYSIS OF BLADES OF AXIAL FLOW FAN USING ANSYS. Mahajan Vandana N.,* Shekhawat Sanjay P.

ANALYSIS OF BLADES OF AXIAL FLOW FAN USING ANSYS. Mahajan Vandana N.,* Shekhawat Sanjay P. Research Article ANALYSIS OF BLADES OF AXIAL FLOW FAN USING ANSYS. Mahajan Vandana N.,* Shekhawat Sanjay P. Address for Correspondence Department of Mechanical Engg. S.S.B.T s College of Engg. and Technology,

More information

SOLAR FLAT PLATE COLLECTOR HEAT TRANSFER ANALYSIS IN THE RAISER WITH HELICAL FINS Mohammed Mohsin Shkhair* 1, Dr.

SOLAR FLAT PLATE COLLECTOR HEAT TRANSFER ANALYSIS IN THE RAISER WITH HELICAL FINS Mohammed Mohsin Shkhair* 1, Dr. ISSN 2277-2685 IJESR/May 2015/ Vol-5/Issue-5/352-356 Mohammed Mohsin Shkhair et. al./ International Journal of Engineering & Science Research SOLAR FLAT PLATE COLLECTOR HEAT TRANSFER ANALYSIS IN THE RAISER

More information

Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics

Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics Yasser Abdel Mohsen, Ashraf Sharara, Basiouny Elsouhily, Hassan Elgamal Mechanical Engineering

More information

GEOMETRICAL PARAMETERS BASED OPTIMIZATION OF HEAT TRANSFER RATE IN DOUBLE PIPE HEAT EXCHANGER USING TAGUCHI METHOD D.

GEOMETRICAL PARAMETERS BASED OPTIMIZATION OF HEAT TRANSFER RATE IN DOUBLE PIPE HEAT EXCHANGER USING TAGUCHI METHOD D. ISSN 2277-2685 IJESR/March 2018/ Vol-8/Issue-3/18-24 D. Bahar et. al., / International Journal of Engineering & Science Research GEOMETRICAL PARAMETERS BASED OPTIMIZATION OF HEAT TRANSFER RATE IN DOUBLE

More information

Modal analysis of Truck Chassis Frame IJSER

Modal analysis of Truck Chassis Frame IJSER Modal analysis of Truck Chassis Frame 158 Shubham Bhise 1, Vaibhav Dabhade 1, Sujit Pagi 1, Apurvi Veldandi 1. 1 B.E. Student, Dept. of Automobile Engineering, Saraswati College of Engineering, Navi Mumbai,

More information

NUMERICAL INVESTIGATION OF EFFECT OF EXHAUST GAS RECIRCULATION ON COMPRESSIONIGNITION ENGINE EMISSIONS

NUMERICAL INVESTIGATION OF EFFECT OF EXHAUST GAS RECIRCULATION ON COMPRESSIONIGNITION ENGINE EMISSIONS ISSN (Online) : 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology An ISO 3297: 2007 Certified Organization, Volume 2, Special Issue

More information

A Study on Performance Enhancement of Heat Exchanger in Thermoelectric Generator using CFD

A Study on Performance Enhancement of Heat Exchanger in Thermoelectric Generator using CFD IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 10 March 2016 ISSN (online): 2349-6010 A Study on Performance Enhancement of Heat Exchanger in Thermoelectric

More information

NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT

NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT BALAKRISHNAN RAJU, CFD ANALYSIS ENGINEER, TATA CONSULTANCY SERVICES LTD., BANGALORE ABSTRACT Thermal loading of piston

More information

Finite Element Analysis on Thermal Effect of the Vehicle Engine

Finite Element Analysis on Thermal Effect of the Vehicle Engine Proceedings of MUCEET2009 Malaysian Technical Universities Conference on Engineering and Technology June 20~22, 2009, MS Garden, Kuantan, Pahang, Malaysia Finite Element Analysis on Thermal Effect of the

More information

THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS

THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS Pushpandra Kumar Patel 1, Vikky Kumhar 2 1 BE Student, 2 Assistant Professor Department of Mechanical Engineering, SSTC-SSGI, Junwani, Bhilai,

More information

Thermal Analysis of Shell and Tube Heat Exchanger Using Different Fin Cross Section

Thermal Analysis of Shell and Tube Heat Exchanger Using Different Fin Cross Section Thermal Analysis of Shell and Tube Heat Exchanger Using Different Fin Cross Section J. Heeraman M.Tech -Thermal Engineering Department of Mechanical Engineering Ellenki College of Engineering & Technology

More information

CFD ANALYSIS OF EXHAUST BACKPRESSURE FOR FOUR-STROKE CI ENGINE

CFD ANALYSIS OF EXHAUST BACKPRESSURE FOR FOUR-STROKE CI ENGINE CFD ANALYSIS OF EXHAUST BACKPRESSURE FOR FOUR-STROKE CI ENGINE Nandkumar Patil 1, Dr.Sharad Chaudhary 2 1 PG Scholar, 2 Professor Mechanical Engineering Department Devi Ahilya Vishwavidyalaya, Indore,

More information

International Journal of Engineering & Science Research

International Journal of Engineering & Science Research International Journal of Engineering & Science Research CFD ANALYSIS AND EXPERIMENTAL VERIFICATION OF EFFECT OF MANIFOLD GEOMETRY ON VOLUMETRIC EFFICIENCY AND BACK PRESSURE FOR MULTI- CYLINDER SI ENGINE

More information

Analysis of Air Flow and Heat Transfer in Ventilated Disc Brake Rotor with Diamond Pillars

Analysis of Air Flow and Heat Transfer in Ventilated Disc Brake Rotor with Diamond Pillars International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2016 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Analysis

More information

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY CFD ANALYSIS OF GAS COOLER FOR ASSORTED DESIGN PARAMETERS B Nageswara Rao * & K Vijaya Kumar Reddy * Head of Mechanical Department,

More information

AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER

AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER E.Saravanapprabhu 1, M.Mahendran 2 1E.Saravanapprabhu, PG Student, Thermal Engineering, Department of Mechanical Engineering,

More information

Investigation for Flow of Cooling Air through the Ventilated Disc Brake Rotor using CFD

Investigation for Flow of Cooling Air through the Ventilated Disc Brake Rotor using CFD International Journal of Thermal Technologies E-ISSN 2277 4114 2015 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijtt/ Research Article Investigation for Flow of Cooling Air

More information

Experimental Investigation on Modification of Inlet poppet valve of single cylinder Direct Ignition Four stroke Diesel Engine

Experimental Investigation on Modification of Inlet poppet valve of single cylinder Direct Ignition Four stroke Diesel Engine Experimental Investigation on Modification of Inlet poppet valve of single cylinder Direct Ignition Four stroke Diesel Engine Dr. Hiregoudar Yerrennagoudaru 1, Shiva prasad Desai 2, Mallikarjuna. A 3 1

More information

Analysis Of Vehicle Air Compressor Mounting Bracket

Analysis Of Vehicle Air Compressor Mounting Bracket Analysis Of Vehicle Air Compressor Mounting Bracket Murtaza Goawala 1,Rahul Giri 2,Niket Phalke 3,Krishna Singh 4,Prof. Nitin Sall 5 1,2,3,4,5 Automobile Engineering Dept., Theem College Of Engineering,

More information

Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny. Turbomachinery 2015, Design of HP and LP turbine connection

Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny. Turbomachinery 2015, Design of HP and LP turbine connection Turbostroje 2015 Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny Turbomachinery 2015, Design of HP and LP turbine connection J. Hrabovský 1, J. Klíma 2, V. Prokop 3, M. Komárek 4 Abstract:

More information

Design and Analysis of Restricted Air Intake for Performance Optimization of Single-Cylinder Engine

Design and Analysis of Restricted Air Intake for Performance Optimization of Single-Cylinder Engine RESEARCH ARTICLE OPEN ACCESS Design and Analysis of Restricted Air Intake for Performance Optimization of Single-Cylinder Engine Darshit Jangid 1, Akshay Sharma 2, Vaibhav Dhama 3 1(Mechanical Engineering,

More information

Simulation Studies on the Effect of Porous Twisted Plate Inserts on the Performance of Fire Tube Steam Packaged Boiler

Simulation Studies on the Effect of Porous Twisted Plate Inserts on the Performance of Fire Tube Steam Packaged Boiler Simulation Studies on the Effect of Porous Twisted Plate Inserts on the Performance of Fire Tube Steam Packaged Boiler S. Hassan *,a, M. K. Roslim b and R. M. Zain c Mechanical Engineering Department,

More information

Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car

Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car Journal of Physics: Conference Series PAPER OPEN ACCESS Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car To cite this article: A Norizan et al 2017

More information

Generation of Air Swirl through Inlet Poppet Valve Modification and To Enhance Performance on Diesel Engine

Generation of Air Swirl through Inlet Poppet Valve Modification and To Enhance Performance on Diesel Engine IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 6 Ver. VI (Nov. - Dec. 2015), PP 55-65 www.iosrjournals.org Generation of Air Swirl through

More information

Effect of Stator Shape on the Performance of Torque Converter

Effect of Stator Shape on the Performance of Torque Converter 16 th International Conference on AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 16 May 26-28, 2015, E-Mail: asat@mtc.edu.eg Military Technical College, Kobry Elkobbah, Cairo, Egypt Tel : +(202) 24025292

More information

CFD analysis of heat transfer enhancement in helical coil heat exchanger by varying helix angle

CFD analysis of heat transfer enhancement in helical coil heat exchanger by varying helix angle CFD analysis of heat transfer enhancement in helical coil heat exchanger by varying helix 1 Saket A Patel, 2 Hiren T Patel 1 M.E. Student, 2 Assistant Professor 1 Mechanical Engineering Department, 1 Mahatma

More information

Design & Thermal Analysis of I.C. Engine Poppet Valves using Solidworks and FEA

Design & Thermal Analysis of I.C. Engine Poppet Valves using Solidworks and FEA Design & Thermal Analysis of I.C. Engine Poppet Valves using Solidworks and FEA Ch. Mani Kumar 1 P. Rajendra Babu 2 1,2Asst. Professor, Dept. of Mechanical Engineering, Sasi Institute of Technology and

More information

Flow Simulation of Diesel Engine for Prolate Combustion Chamber

Flow Simulation of Diesel Engine for Prolate Combustion Chamber IJIRST National Conference on Recent Advancements in Mechanical Engineering (RAME 17) March 2017 Flow Simulation of Diesel Engine for Prolate Combustion Chamber R.Krishnakumar 1 P.Duraimurugan 2 M.Magudeswaran

More information

Computational Investigation of Normal and Hybrid Cooling Fins of Internal Combustion Engine

Computational Investigation of Normal and Hybrid Cooling Fins of Internal Combustion Engine Computational Investigation of Normal and Hybrid Cooling Fins of Internal Combustion Engine Aswin Mohan, R. Titus, Adarsh Kumar.P.S Abstract In this research work a hybrid material (Aluminium-Copper) compound

More information

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Vikas Kumar Agarwal Deputy Manager Mahindra Two Wheelers Ltd. MIDC Chinchwad Pune 411019 India Abbreviations:

More information

Exhaust Gas Waste Heat Recovery and Utilization System in IC Engine

Exhaust Gas Waste Heat Recovery and Utilization System in IC Engine IJIRST International Journal for Innovative Research in Science & Technology Volume 1 Issue 11 April 2015 ISSN (online): 2349-6010 Exhaust Gas Waste Heat Recovery and Utilization System in IC Engine Alvin

More information

Experimental Investigation and Analysis of Single Cylinder Four Stroke C.I. Engine Exhaust System

Experimental Investigation and Analysis of Single Cylinder Four Stroke C.I. Engine Exhaust System International Journal of Energy and Power (IJEP) Volume 3 Issue 1, February 2014 www.ijep.org Experimental Investigation and Analysis of Single Cylinder Four Stroke C.I. Engine Exhaust System Atul A. Patil

More information

FEM Analysis of Combined Paired Effect on Piston & Connecting Rod using ANSYS

FEM Analysis of Combined Paired Effect on Piston & Connecting Rod using ANSYS FEM Analysis of Combined Paired Effect on Piston & Connecting Rod using ANSYS Kunal Saurabh Assistant Professor, Mechanical Department IEC Group of Institutions, Greater Noida - India kunalsaurabh.me@ieccollege.com

More information

Analysis Of Gearbox Casing Using FEA

Analysis Of Gearbox Casing Using FEA Analysis Of Gearbox Casing Using FEA Neeta T. Chavan, Student, M.E. Design, Mechanical Department, Pillai Hoc, Maharashtra, India Assistant Prof. Gunchita Kaur-Wadhwa, Mechanical Department Pillai Hoc,

More information

Thermal Analysis on 4 1 Tubular Type IC-Engine Exhaust Manifold through Anysis

Thermal Analysis on 4 1 Tubular Type IC-Engine Exhaust Manifold through Anysis International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume 4, Number 7 (2014), pp. 755-762 Research India Publications http://www.ripublication.com Thermal Analysis on 4 1 Tubular

More information

IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online):

IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online): IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online): 2321-0613 Effect of Aspiration Pressure on Convergent Nozzle Employed for Gas Atomization of Liquid

More information

Optimization of Seat Displacement and Settling Time of Quarter Car Model Vehicle Dynamic System Subjected to Speed Bump

Optimization of Seat Displacement and Settling Time of Quarter Car Model Vehicle Dynamic System Subjected to Speed Bump Research Article International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347-5161 2014 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Optimization

More information

MULTI-BODY DYNAMIC ANALYSIS OF AN IC ENGINE PISTON FOR SHAPE OPTIMIZATION

MULTI-BODY DYNAMIC ANALYSIS OF AN IC ENGINE PISTON FOR SHAPE OPTIMIZATION Int. J. Mech. Eng. & Rob. Res. 2014 Shivayogi S Hiremath and I G Bhavi, 2014 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 4, October 2014 2014 IJMERR. All Rights Reserved MULTI-BODY DYNAMIC

More information

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 1.852

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 1.852 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY Design Analysis and Optimization of Piston and Determination of its Thermal Stresses Using CAE Tools Deovrat Vibhandik *1, Ameya

More information

Keywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION

Keywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION Finite Element Analysis of IC Engine Piston Using Thermo Mechanical Approach 1 S.Sathishkumar, Dr.M.Kannan and 3 V.Raguraman, 1 PG Scholar, Professor, 3 Assistant professor, 1,,3 Department of Mechanical

More information

EFFECT OF SPOILER DESIGN ON HATCHBACK CAR

EFFECT OF SPOILER DESIGN ON HATCHBACK CAR EFFECT OF SPOILER DESIGN ON HATCHBACK CAR Ashpak Kazi 1 *, Pradyumna Acharya 2, Akhil Patil 3 and Aniket Noraje 4 1,2,3,4 Department of Automotive Engineering, School of Mechanical Engineering, VIT University,

More information

COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A.

COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A. COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report 412509-1R0 By Kimbal A. Hall, PE Submitted to: WESTFALL MANUFACTURING COMPANY May 2012 ALDEN RESEARCH

More information

Corresponding Author, Dept. of Mechanical & Automotive Engineering, Kongju National University, South Korea

Corresponding Author, Dept. of Mechanical & Automotive Engineering, Kongju National University, South Korea International Journal of Mechanical & Mechatronics Engineering IJMME-IJENS Vol:15 No:04 62 A Study on Enhancing the Efficiency of 3-Way Valve in the Fuel Cell Thermal Management System Il Sun Hwang 1 and

More information

Stress Analysis of Engine Camshaft and Choosing Best Manufacturing Material

Stress Analysis of Engine Camshaft and Choosing Best Manufacturing Material Stress Analysis of Engine Camshaft and Choosing Best Manufacturing Material Samta Jain, Mr. Vikas Bansal Rajasthan Technical University, Kota (Rajasathan), India Abstract This paper presents the modeling

More information

International Journal of Scientific & Engineering Research, Volume 7, Issue 3, March ISSN DESIGN AND ANALYSIS OF A SHOCK ABSORBER

International Journal of Scientific & Engineering Research, Volume 7, Issue 3, March ISSN DESIGN AND ANALYSIS OF A SHOCK ABSORBER International Journal of Scientific & Engineering Research, Volume 7, Issue 3, March-2016 19 DESIGN AND ANALYSIS OF A SHOCK ABSORBER Johnson*, Davis Jose, Anthony Tony Abstract: -Shock absorbers are a

More information

NUMERICAL INVESTIGATION OF FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS ON THE AERODYNAMICS OF VENTILATED DISC BRAKE ROTOR USING CFD

NUMERICAL INVESTIGATION OF FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS ON THE AERODYNAMICS OF VENTILATED DISC BRAKE ROTOR USING CFD THERMAL SCIENCE: Year 2014, Vol. 18, No. 2, pp. 667-675 667 NUMERICAL INVESTIGATION OF FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS ON THE AERODYNAMICS OF VENTILATED DISC BRAKE ROTOR USING CFD by Thundil

More information

Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics

Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics M. Metwally Lecturer, Ph.D., MTC, Cairo, Egypt Abstract Modern offset printing machine, paper

More information

Design and Performance Analysis of Louvered Fin Automotive Radiator using CAE Tools

Design and Performance Analysis of Louvered Fin Automotive Radiator using CAE Tools Design and Performance Analysis of Louvered Fin Automotive Radiator using CAE Tools Vishwa Deepak Dwivedi Scholar of Master of Technology, Mechanical Engineering Department, UCER, Allahabad, India Ranjeet

More information

Comparison Of Multibody Dynamic Analysis Of Double Wishbone Suspension Using Simmechanics And FEA Approach

Comparison Of Multibody Dynamic Analysis Of Double Wishbone Suspension Using Simmechanics And FEA Approach International Journal of Research in Engineering and Science (IJRES) ISSN (Online): 232-9364, ISSN (Print): 232-9356 Volume 2 Issue 4 ǁ April. 214 ǁ PP.31-37 Comparison Of Multibody Dynamic Analysis Of

More information

Development of Shape of Helmholtz Resonator Cavity for Attenuation of Low Frequency Noise of Pure Reactive Muffler

Development of Shape of Helmholtz Resonator Cavity for Attenuation of Low Frequency Noise of Pure Reactive Muffler Development of Shape of Helmholtz Resonator Cavity for Attenuation of Low Frequency Noise of Pure Reactive Muffler Amit Kumar Gupta 1, Nirmal Gupta 2 1 Assistant Professor, 2 M.E. Scholar Mechanical Engineering

More information

International Journal of Advance Engineering and Research Development

International Journal of Advance Engineering and Research Development Scientific Journal of Impact Factor (SJIF): 3.134 International Journal of Advance Engineering and Research Development Volume 2, Issue 12, December -2015 e-issn (O): 2348-4470 p-issn (P): 2348-6406 An

More information

Design Optimization of Catalytic Converter to reduce Particulate Matter and Achieve Limited Back Pressure in Diesel Engine by CFD

Design Optimization of Catalytic Converter to reduce Particulate Matter and Achieve Limited Back Pressure in Diesel Engine by CFD Research Article International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347-5161 2014 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Design

More information

2.61 Internal Combustion Engines Spring 2008

2.61 Internal Combustion Engines Spring 2008 MIT OpenCourseWare http://ocw.mit.edu 2.61 Internal Combustion Engines Spring 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. Engine Heat Transfer

More information

DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION

DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION N. A. Mohamad Shafie 1, M. F. Muhamad Said 1, Z. Abdul Latiff 1 and S. Rajoo 2 1 Automotive

More information

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings Research Article International Journal of Current Engineering and Technology ISSN 2277-4106 2013 INPRESSCO. All Rights Reserved. Available at http://inpressco.com/category/ijcet Simulation of Performance

More information

Comparison of Velocity Vector Components in a Di Diesel Engine: Analysis through Cfd Simulation

Comparison of Velocity Vector Components in a Di Diesel Engine: Analysis through Cfd Simulation IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X PP. 55-60 www.iosrjournals.org Comparison of Velocity Vector Components in a Di Diesel Engine: Analysis

More information

Engine Heat Transfer. Engine Heat Transfer

Engine Heat Transfer. Engine Heat Transfer Engine Heat Transfer 1. Impact of heat transfer on engine operation 2. Heat transfer environment 3. Energy flow in an engine 4. Engine heat transfer Fundamentals Spark-ignition engine heat transfer Diesel

More information

THE STUDY ON EFFECT OF TORQUE ON PISTON LATERAL MOTION

THE STUDY ON EFFECT OF TORQUE ON PISTON LATERAL MOTION THE STUDY ON EFFECT OF TORQUE ON PISTON LATERAL MOTION Vinay V. Kuppast 1, S. N. Kurbet 2, A. M. Yadawad 3, G. K. Patil 4 1 Associate Professor, 2 Professor & Head, 4 Associate Professor, Department of

More information

EXPERIMENTAL INVESTIGATION OF THERMAL PERFORMANCE OF PETROL ENGINE USING FUEL CATALYST

EXPERIMENTAL INVESTIGATION OF THERMAL PERFORMANCE OF PETROL ENGINE USING FUEL CATALYST EXPERIMENTAL INVESTIGATION OF THERMAL PERFORMANCE OF PETROL ENGINE USING FUEL CATALYST Sagar.A.Patil 1, Priyanka.V.Kadam 2, Mangesh.S.Yeolekar 3, Sandip.B.Sonawane 4 1 Student (Final Year), Department

More information

Static Structural and Thermal Analysis of Aluminum Alloy Piston For Design Optimization Using FEA Kashyap Vyas 1 Milan Pandya 2

Static Structural and Thermal Analysis of Aluminum Alloy Piston For Design Optimization Using FEA Kashyap Vyas 1 Milan Pandya 2 IJSRD - International Journal for Scientific Research & Development Vol. 2, Issue 03, 2014 ISSN (online): 2321-0613 Static Structural and Thermal Analysis of Aluminum Alloy Piston For Design Optimization

More information

Noise Reduction in a Reciprocating Compressor by Optimizing the Suction Muffler

Noise Reduction in a Reciprocating Compressor by Optimizing the Suction Muffler Noise Reduction in a Reciprocating Compressor by Optimizing the Suction Muffler Katakama Nagarjuna ¹ K.Sreenivas² ¹ M.tech student, ²Professor, dept of mechanical engineering kits, markapur, A.P, INDIA

More information

DESIGN AND ANALYSIS OF MUFFLER TO REDUCE THE BACK PRESSURE

DESIGN AND ANALYSIS OF MUFFLER TO REDUCE THE BACK PRESSURE 470 DESIGN AND ANALYSIS OF MUFFLER TO REDUCE THE BACK PRESSURE Ch.Indira Priyadarsini 1, Madhav Modali 2, Sangepu Vamshi Krishna 3, N Dinesh Reddy 4 1 Assistant Professor, Mechanical Engg. Dept., Chaitanya

More information

International Journal of Engineering Research and General Science Volume 5, Issue 3, May-June, 2017 ISSN

International Journal of Engineering Research and General Science Volume 5, Issue 3, May-June, 2017 ISSN HEAT TRANSFER AND FLUID FLOW ANALYSIS OF CIRCULAR RECEIVER TUBE OF SOLAR COLLECTOR Swati Patel 1, M.A.Kadam 2 1 P.G. Student, Department of Mechanical Engineering, Bharati Vidyapeeth Deemed University,

More information

Heat Transfer Enhancement for Double Pipe Heat Exchanger Using Twisted Wire Brush Inserts

Heat Transfer Enhancement for Double Pipe Heat Exchanger Using Twisted Wire Brush Inserts Heat Transfer Enhancement for Double Pipe Heat Exchanger Using Twisted Wire Brush Inserts Deepali Gaikwad 1, Kundlik Mali 2 Assistant Professor, Department of Mechanical Engineering, Sinhgad College of

More information

Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications

Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications TAEWOO KIM 1, SULMIN YANG 2, SANGMO KANG 3 1,2,4 Mechanical Engineering Dong-A University 840 Hadan 2 Dong, Saha-Gu,

More information

CFD Analysis of a Gasoline Engine Exhaust Pipe

CFD Analysis of a Gasoline Engine Exhaust Pipe CFD Analysis of a Gasoline Engine Exhaust Pipe Pengyun Xu*, Haiyong Jiang, Xiaoshun Zhao College of Mechanical & Electronical Engineering Agricultural University of Hebei Baoding, Hebei, China Abstract

More information

Plastic Ball Bearing Design Improvement Using Finite Element Method

Plastic Ball Bearing Design Improvement Using Finite Element Method 2017 Published in 5th International Symposium on Innovative Technologies in Engineering and Science 29-30 September 2017 (ISITES2017 Baku - Azerbaijan) Plastic Ball Bearing Design Improvement Using Finite

More information

CFD ANALYSIS OF PRESSURE DROP CHARACTERISTICS OF BUTTERFLY AND DUAL PLATE CHECK VALVE

CFD ANALYSIS OF PRESSURE DROP CHARACTERISTICS OF BUTTERFLY AND DUAL PLATE CHECK VALVE CFD ANALYSIS OF PRESSURE DROP CHARACTERISTICS OF BUTTERFLY AND DUAL PLATE CHECK VALVE Adarsh K M 1, Dr. V Seshadri 2 and S. Mallikarjuna 3 1 M Tech Student Mechanical, MIT-Mysore 2 Professor (Emeritus),

More information

PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF

PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF PROJECT REFERENCE NO. : 37S1036 COLLEGE BRANCH GUIDES : KS INSTITUTE OF TECHNOLOGY, BANGALORE

More information

6340(Print), ISSN (Online) Volume 3, Issue 3, Sep- Dec (2012) IAEME AND TECHNOLOGY (IJMET)

6340(Print), ISSN (Online) Volume 3, Issue 3, Sep- Dec (2012) IAEME AND TECHNOLOGY (IJMET) INTERNATIONAL International Journal of Mechanical JOURNAL Engineering OF MECHANICAL and Technology (IJMET), ENGINEERING ISSN 0976 AND TECHNOLOGY (IJMET) ISSN 0976 6340 (Print) ISSN 0976 6359 (Online) Volume

More information

DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS

DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS GAJENDRA G 1, PRAKASHA A M 2, DR NOOR AHMED R 3, DR.K.S.BADRINARAYAN 4 1PG Scholar, Mechanical department, M S Engineering College,

More information