Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches
|
|
- Shona Knight
- 5 years ago
- Views:
Transcription
1 Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools Required: Personal Protective Equipment (Gloves and Eye Protection) Properly rated voltage sensing device. 1/4" Torque Controlled Driver with magnetic socket. 5/16" Torque Controlled Driver with magnetic socket. Small work table and screw bin. Reference Pictures & Comments 1 Turn OFF and lock out all power supplying this switch before installing base kit. 2 Turn switch to "OFF" position. 3 Verify there is NO voltage present at the line and load terminals using a properly rated voltage sensing device. 1 of 8
2 4 Remove fuses. 5 Remove yellow arc shield using a 1/4" driver. (1 screw) 6 For fusible switches remove middle load side fuse clip connector screw with 1/4" driver. Keep screw for reinstallation. 7 Remove insulator screw with 1/4" driver and remove insulator. Keep parts for reinstallation. Insulator used only on 60 amp and 30 amp Canadian models. 2 of 8
3 8 Remove two screws with 5/16" driver from the lower fuse base and lower it out of the way. Keep screws for reinstallation. x2 9 If equipped with a neutral or control pole, loosen mounting screw with 5/16" driver and slide to the left. Screw is captivated by plastic base and does not need removed. 10 Mark the line side lugs before removing so they can be reinstalled back in their original phase locations. 11 Remove screws from line side lugs using 5/16" driver. Move wires to the side for base removal. Keep screws for reinstallation on new base. x3 3 of 8
4 12 Remove switch base with 5/16 driver. (3 screws, 2 on bottom, 1 on top) Keep screws for reinstallation on new base. 13 Slide base to left to disengage shaft from mechanism. Remove insulator. Keep insulator if present for reinstallation on new base. Insulator used only on 60 amp models. 14 Verify there is no foreign material left in the mechanism shaft coupling. This could cause misalignment and premature failure of the new base. 15 Remove three fuse clips with 5/16" driver and keep for reinstallation. x3 16 Remove three fuse puller straps with 1/4" driver and keep for reinstallation. 4 of 8
5 17 Remove universal base and hardware from box verifying the following contents. 1-Universal Base 3-Lug Stops - *Not used for fusible devices. 3-Lug Stop Screws - *Not used for fusible devices. 18 Reinstall three fuse clips from original base with 5/16" driver on new base assembly. Make sure retainer tang is up as shown in picture. Torque to in-lbs. x3 19 Reinstall three fuse puller straps from original base with 1/4" driver on new base assembly. Torque to in-lbs. 20 Rotate switch base shaft counter-clockwise to put switch blades in open/off position. Place insulator on mechanism. *Insulators used only on 60 amp models. 5 of 8
6 21 Align base mounting holes and install 3 screws with 5/16" driver. (1 on top, 2 on bottom) Torque to 20 to 25 in-lbs. 22 Align fuse base and install 2 mounting screws with 5/16" driver. Torque to 20 to 25 in-lbs. x2 23 Reinstall insulator and and retainer screw with 1/4" driver. The right side of the insulator wraps around the switch base wall as shown. Torque to 20 to 30 in-lbs. Insulator used only on 60 amp and 30 amp Canadian models. 24 Position load side fuse clip connector onto the locator tabs and fasten with screw using 1/4" driver. Torque to in-lb. LOCATORS 6 of 8
7 25 Remove arc shield mounting screw with 1/4" driver. Remove arc shield. Keep screw and arc shield for reinstallation. x1 26 Reattach line side lugs using 5/16" driver. Torque to in-lbs. x3 NIB 27 If device has a neutral or control pole, reinstall. Note : Two nibs on the side fit into notches on the side of the base. Tighten mounting screw to 20 to 25 in-lbs. NIB 28 Reattach arc shield. Torque to in-lbs. x1 7 of 8
8 29 Install fuses. 30 Verify all parts are in place and screws torqued to specification. 31 Hold in mechanism-defeat lever and actuate switch 3-4 times verifying switch blades are opening and closing properly. 32 Prior to energization remove any loose materials or tools from the switch enclosure. Close cover before turning power on ahead of switch. 8 of 8
Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches
Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools Required: Personal Protective
More informationInstallation Instructions for Replacement Mechanism Kit
s Siemens Industry,Inc. Item: Replacement Switch Kit Catalog Numbers HM6123 & HM6123S For use with: 30-100 Amp VBII Safety Switches Page 1 of 5 SAFETY INSTRUCTIONS NOTE: This instruction outlines the recommended
More informationBulletin 1494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 1494C- _ Series 2 : 600A)
Bulletin 494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 494C- _ Series : 600A) ATTENTION: To prevent electrical shock, disconnect from power source before installing or
More informationBulletin 1494C Cable Operated Disconnect Switch Kit (400A) Installation Instructions (Cat 1494C- _ Series 2 : 400A)
Bulletin 494C Cable Operated Disconnect Switch Kit () Installation Instructions (Cat 494C- _ Series : ) ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
More informationBulletin 1494V Variable Depth Disconnect Switch Installation Instructions (Cat 1494V-DS400; -DSX400 - Series D)
Bulletin 494V Variable Depth Disconnect Switch Installation Instructions (Cat 494V-DS400; -DSX400 - Series D) ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
More informationFord Racing GT500 Style Strut Mount Upgrade (05-12 All):
Ford Racing GT500 Style Strut Mount Upgrade (05-12 All): Required tools: (2) Jack stands Floor jack (1 is required but 2 is preferred) Torque wrench Spring compressor tool (can be rented at your local
More informationEibach Pro-Damper Shocks & Struts (05-09 All):
Eibach Pro-Damper Shocks & Struts (05-09 All): Required tools: 3/8 and 1/2 drive ratchets 7, 8, 10, 15, 16, 17, 18, 21 & 22 mm open ended wrenches 8 & 10 mm box end wrenches 10mm socket 13, 15 & 18 mm
More informationBulletin 1494V Variable Depth, Flange Operated Disconnect Switch Kits for 400 and 600 Amperes (Series A) Switches
Bulletin 494V Variable Depth, Flange Operated Disconnect Switch Kits for and Amperes (Series A) Switches ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
More informationInstruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents
Instruction Sheet Kit Numbers: 5600, 5700, 5800 & 5300 CRANK PULLEY KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand, and follow all safety
More information920 Remote Control Switches
920 Remote Control Switches REMOTE CONTROL SWITCHES Service Bulletin This service bulletin for ASCO 920 Remote Control Switches explains how to replace the main s, operator coil, control s, and how to
More informationThe steering column is of a modular construction and features easy to service electrical switches.
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationDigitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers
Supersedes IL 33-858-4 Dated 05/02 Digitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers Digitrip Retrofit System for ITE K-3000, Digitrip Retrofit System for ITE K-3000, K-3000
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationCable-Operated Disconnect Switches. Accessories
Cable-Operated Disconnect Switches Accessories Description For Use With Auxiliary Contacts 1 N.O. Contact 1494C, 1494F, 1494V, and 1494G ( 1495-N8 1 N.O. Contact (low-level switching) A) Disconnect Switches
More informationTable of Contents. Quick Installation Guide 2 - Disconnect Switch Installation - Disconnect Handle Installation - Cutting Connecting Rod
ulletin 494V Variable Depth Disconnect Switch Installation Instructions (Cat 494V-DS30; -DSX30 - Series D; 494V-DS; -DSX - Series D) (Cat 494V-DS00; -DSX00 - Series D; 494V-DS00; -DSX00 - Series D) TTENTION:
More information918 Remote Control Switches
98 Remote Control Switches Remote Control Switches This service bulletin explains how to replace the coil, control circuit board, miniature switch, and the contact block(s) in ASCO 98 remote control switches.
More informationIntake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter)
Intake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter) Year/Make/Model/Engine 2012-17 Ford Focus 2.0L Parts List 1- Intake tube 1- Heat shield, Side 1-
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationINSTALLATION INSTRUCTIONS FORD SUPER DUTY NOTE: (Vehicle Retains Tow Hook) PART # P3064
INSTALLATION INSTRUCTIONS 2011-14 FORD SUPER DUTY 250-550 NOTE: (Vehicle Retains Tow Hook) PART # P3064 PARTS LIST: Qty Description Qty Description 1 Grill Guard 2 10mm x mm Hex Bolts 1 Driver/Left Lower
More informationTEC Actuator Package. Product and Part Numbers. Product Description. Installation Instructions Document No October 27, 2010 CAUTION:
Document No. 550-00 TEC Actuator Package AUTOZERO MODULE (OPTIONAL) CABLE TIE TEC00R BASE-PLATE Figure. TEC Actuator Package, with Optional Autozero Module. DO NOT CUT CABLE TIE FASTENED AROUND ACTUATOR
More informationEffective June 2016 New Issue
Voltage Regulators MN225035EN Effective June 2016 New Issue COOPER POWER SERIES QD8 Quik-Drive Tap-Changer Switch Assembly Kit 5740785B13 and Switch Neutral Stationary Assembly Kit 5791646A48 Installation
More informationService Manual. Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Service Manual Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY This Service Manual is not a substitute for the Operator s Manual. You must read, understand and
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS APPLICATION: DODGE CHARGER POLICE PUSH BAR (2011 & UP) APP PART # 36-2035 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 PUSH BAR ASSEMBLY RATCHET 2,3 2
More informationInstruction Sheet Kit Number:
Instruction Sheet Kit Number: 7914400 POWERED DECK LIFT KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand and follow all safety practices
More informationVan Rack Installation Manual Ford Transit Connect
1.888.772.8400 Big to small... We do it all Van Rack Installation Manual Ford Transit Connect Thank you for your purchase of an Unruh Fab Van rack. We have designed and built this rack so that you can
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationCOOKSON OWNER'S MANUAL
COOKSON OWNER'S MANUAL FD-2A AUTOMATIC RESETTING FIRE DOOR HOIST OPERATOR R US RECOGNIZED COMPONENT CONFORMS TO UL 325 3040233 9045.DWG ECN 0986 REV 2 PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENTS:
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2007-2017 Chevy Silverado / GM Sierra / 1500-2500-3500 Ext. / Double / Crew Cab PART NUMBER: 56-13715, 56-13725 ITEM QUANTITY DESCRIPTION
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1963-67 Corvette P/N: 121620 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More informationINSTALLATION & OPERATION MANUAL. Fan Powered Terminals VAV TERMINALS. Redefine your comfort zone.
INSTALLATION & OPERATION MANUAL Fan Powered Terminals VAV TERMINALS IOM FAN POWERED TERMINALS Receiving Inspection After unpacking the terminal, check it for shipping damage. If any shipping damage is
More informationUniversal Super Shield & Ultimate Aluminum w/electric Drive Conversion Kits , , Installation Instructions
WLH 09/19/16 111-0215 & 112-0215 607-0026 For technical support call us at (800) 368-3075 or visit our website at PullTarps.com. TABLE OF CONTENTS ***Assembly*** Conversion Kit-Universal Super Shield ***Wiring,
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationDisconnect Switches Type VBII (30-600A) with Flange Mounted Operating Handle
Features 30-600A, 600VAC and DC ratings UL Recognized (file # E121152 vol. 3) and CSA Certified under file number 15852 Visible blade quick make and break switching action Panel and Flange mounted assemblies
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationDo not have any open flame or heat sources close to the installation
March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew
More information8mm Bolt Plate. (15) 8mm U-Clip Nuts. Passenger/right front Upper Bracket
PARTS LIST: 2 T-6 Side Bars 8 8mm Double Bolt Plates 1 Passenger/right Upper Bracket (all incl. DEF) 17 8-1.25mm x 25mm Hex Bolts 1 Passenger/right Lower Bracket (all incl. DEF) 33 8mm x 24mm x 2mm Flat
More information1.5 WIPER MOTOR INSTALLATION INSTRUCTIONS (ITEM # S: 71081, 71011, 71082, 71012, 71182, 71112)
1.5 WIPER MOTOR INSTALLATION INSTRUCTIONS (ITEM # S: 71081, 71011, 71082, 71012, 71182, 71112) The Marinco 1.5 Wiper Motor features: Fully sealed base and housing which allows installation in wet locations.
More informationInstallation Instructions For Motor Control Center (MCC) Units
s Page 1 of 8 Installation Instructions December, 2013 Installation Instructions For Motor Control Center (MCC) Units Hazardous voltage. Will cause death or serious injury. Always de-energize and ground
More informationConflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio
TOYOTA YARIS SEDAN 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: JBL Audio, Factory Navigation,
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationTOYOTA COROLLA L, LE FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814
TOYOTA COROLLA L, LE 2014-16 FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog
More informationDODGE RAM QUAD CAB. Vehicle Specific Subwoofer Enclosure. Made in the USA
DODGE RAM QUAD CAB Vehicle Specific Subwoofer Enclosure Made in the USA READ ALL DIRECTIONS CAREFULLY BEFORE BEGINNING MOUNTING LOCATION: The enclosure mounts under the rear seat on Dodge Quad Cab Trucks.
More informationMINI COOPER HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT DESIGNED FOR USE WITH BALL MOUNT # D-19 / 45519
10/8/2012 PAGE 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED RATCHET TORQUE WRENCH 12" EXTENSION 12mm SOCKET 8mm SOCKET OFFSET SCREWDRIVER FLAT BLADE
More informationEPLX and D2LX lighting panelboards Installation & maintenance information IF 1813 APPLICATION D2LX/EPLX IF SHEET TABLE OF CONTENTS WEIGHTS
EPLX and D2LX lighting panelboards Installation & maintenance information APPLICATION EPLX and D2LX panelboards provide a centrally controlled switching system and short circuit protection for feeder or
More informationInstalling the Boxer fan upgrade kit
Installing the Boxer fan upgrade kit To reduce projector noise and improve cooling install the fan upgrade kit. Affected products The following products are affected: Boxer 4K30 Mirage 304K Parts list
More informationM9206-Bxx-2S Series On/Off Electric Spring Return Actuators
Installation Instructions M9206-Bxx-2S Issue Date May 14, 2003 M9206-Bxx-2S Series On/Off Electric Spring Return Actuators Installation IMPORTANT: Use this M9206-Bxx-2S Series actuator to control equipment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS.
TITAN pt. no.: 02 0000 0209 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS Gen6 Extended Capacity Replacement
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationAnti-Sway Bars Installation Instructions For Mazda MX-5 PART #
Anti-Sway Bars Installation Instructions For 2006+ Mazda MX-5 PART # 920-330 Tools required: A jack and jack stands, 5mm Allen wrench, ratchet, 10mm, 12mm and 14mm, combination wrenches and sockets, 21mm
More informationTOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation
TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More informationLAMP BULB SERVICE TABLE OF CONTENTS
8L - 6 LAMPS XJ LAMP BULB SERVICE TABLE OF CONTENTS AND FRONT POSITION LAMP BULB...6 SIDE REPEATER LAMP BULB...6 AND FRONT POSITION LAMP BULB REAR FOG LAMP BULB...7 LICENSE PLATE LAMP BULB...7 (3) Pull
More informationBulletin 1494F Fixed-Depth Flange-Mounted Disconnect Switches. Selection Guide
F Fixed-Depth Flange-Mounted Disconnect Switches Selection Guide F Fixed-Depth Flange-Mounted Disconnect Switches Product Cat. No. 1494F-N Disconnect Switch with Cat. No. 1494F-F Fuse Block Adapter Plate
More informationCHEVY SILVERADO CREW CAB RX3 Includes models equipped with DEF tank
2007-2017 CHEVY SILVERADO 1500-3500 CREW CAB RX3 Includes models equipped with DEF tank HARDWARE INCLUDED RECOMMENDED TOOLS 1 Passenger Side Front Support Plate 13mm Wrench 1 8-1.25 x 40mm Hex Bolt 13mm
More informationPARTS LIST: VIEWPOINT RUNNING BOARD NISSAN MURANO EXCLUDES 2dr CROSSCABRIOLET CONVERTIBLE
PARTS LIST: VIEWPOINT RUNNING BOARD Qty Description Qty Description 1 Driver/Left Running Board 14 10-1.5mm x 35mm Bolt Plates 1 Passenger/Right Running Board 6 10-1.50mm x 30mm Hex Bolt 1 Driver/Left
More informationPARTS LIST: HEAVY DUTY FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: HEAVY DUTY FRONT BUMPER 1 Heavy Duty Bumper Assembly 18 12-1.75mm x 50mm Hex Bolts 1 Driver/Left Frame Mounting Bracket 36 12mm x 32mm x 3mm Flat Washers 1 Passenger/Right Frame Mounting Bracket
More information3/8 Universal Joint Phillips Head Screwdriver
Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER 2018 FORD F150
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 28 12mm x 37mm x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 4 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 12
More informationGLACIER PRO RANGER MID SIZE MOUNT KIT
GLACIER PRO RANGER MID SIZE MOUNT KIT P/N 2880261 APPLICATION FOR USE WITH THE GLACIER PRO MID SIZE PLOW SYSTEM (P/N 2880260) ON 2010 AND NEWER RANGER MID SIZE MODELS BEFORE YOU BEGIN Read these instructions
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
More informationFeeder Circuit Breaker Units Secure Support Pan and Change Door Latch
Installation Instructions Feeder Circuit Breaker Units Secure Support Pan and Change Door Latch Catalog Numbers 2193FZ Topic Page About This Publication 1 Required Tools 1 Important User Information 2
More informationCONTENTS: 1EA. SUBWOOFER HARNESS 2PIECE TOOLS REQUIRED:
CONTENTS: 1EA. SUBWOOFER ENCLOSURE 1EA. SUBWOOFER HARNESS 2PIECE 2EA. T-TAP 1EA. FUSE 30 AMP 6EA. WIRE TIES 1EA. INSTRUCTIONS P/N 77KICK14SUBASSEMBLY P/N RHPM1 P/N RFTTAPB P/N RFUSE30 P/N RFZIP6 P/N RBI77KICK14
More informationPart Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short 2000105-2 1 PFadvantage Bracket PF3000 Pro 2000773 1 Cable Kit
More informationSERVICE BULLETIN SB.DSL rev02
DSL 505 Rear Delt / Pec Fly Cable Repair Applies to DSL 505 Rear Delt / Pec Fly built prior to 5/16/2017 Issue/Symptoms On some machines using the 1/8 diameter lift cables, the cam cables may twist and
More informationIsolation Switch (behind barrier & inspection window) Power Fuses. Load Cable Connection Box. Contactor. Control Power Transformer Secondary Fuse
Instruction Bulletin Class 8198 ISO-FLEX Medium Voltage Controller Model 3, Series B Installation and Maintenance Bulletin No. 50006-376-01 August, 1995 Raleigh, NC, USA TABLE OF CONTENTS Introduction...
More informationConflicts NOTE: XLE, LE, AND SE MODELS
TOYOTA SIENNA 2011- REARSIGHT Part Number: 00016-00085 Accessory Code: MC9 Conflicts NOTE: XLE, LE, AND SE MODELS KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA
More information10260 Retrofit to 10260A Non-Contact Sensor Instructions Kits through -512
10260 Retrofit to 10260A Non-Contact Sensor Instructions Kits 51404974-501 through -512 Document Number Form: 62-86-33-16D Effective: 3-1-01 Supersedes: 11-00 Summary Retrofitting your 10260 actuator from
More informationP3066 INSTALLATION MANUAL
P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket
More information8mm Bolt Plate. Passenger/right front only Upper Mounting Bracket
4 SIDE STEPS PARTS LIST: 1 Driver/left Side Step 13 8-1.25mm x 25mm Hex Bolts 1 Passenger/right Side Step 13 8mm x 24mm x 2mm Flat Washers 1 Passenger/right Upper Bracket (all incl. DEF) 13 8mm Lock Washers
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 29191 CIVIC AM/FM CD TUNER 2 and 4 DOOR (DX) Issue Date SEP 2005 PARTS LIST Pocket Attachment Kit P/N 08B60-SCV-100 AM/FM CD Tuner P/N
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationTOYOTA CAMRY FOG LIGHT (Halogen and LED) Part Number: TCA-312 / TCA-812
Part Number: TCA-312 / TCA-812 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light Bezels 3 1 Switch Assembly 4 1 Fog Light Operation Guide 5 1 Harness Bag Hardware Bag Contents
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24664-25319 SYSTEM 2003 CR-V Issue Date MAY 2003 PARTS LIST Security System (sold separately) P/N 08E51-EP4-100 Security System Attachment
More information8G Brake Assembly Alignment
8G Brake Assembly Alignment 8G (9-5250) This document explains how to do the 8G (9-5250) brake assembly alignment in order to eliminate noise in the drive system coming from the mis-aligned brake plates.
More informationRetrofit Steering Column Installation Instructions
Retrofit Steering Column Installation Instructions for 1965-66 Mustangs www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 PH: (517) 424-0577 FAX: (517) 424-7293 Revised 3/22/2010 Instruction #: 8000000011
More informationPart Number: TCO-314 / TCO-814
Date: 05.02.2014 TOYOTA COROLLA L, LE 2014-15 FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Switch
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationInstruction Bulletin. Jockey Pump Controller
Instruction Bulletin Jockey Pump Controller Installation Start Up Service This instruction bulletin is a guide for personnel involved with maintenance, engineering and approval of Fire Pump equipment and
More informationTidland Internal Element Shaft
TIDLAND WINDING SOLUTIONS Tidland Internal Element Shaft Installation, Operation and Maintenance Manual EN Ultrashaft MI 27L132426 1 S IMPORTANT SAFETY INSTRUCTIONS When using this Tidland product, basic
More informationWheel Horse. 36 Tiller. Model No & Up. Operator s Manual
FORM NO. 8 9 Rev. A Wheel Horse 6 Tiller for Classic Garden Tractors Model No. 7970 690000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN GRILLE GUARD / HDX GRILLE GUARD APPLICATION: 2016 Chevrolet Silverado 1500 PART NUMBER: 40-3875, 45-3870, 57-3870, 57-3875 ITEM QUANTITY DESCRIPTION
More informationCM3000 SIGNAL TRANSMITTER. Introduction. The MAXIGARD CM3000 is designed to convert shaft speed into a 4/20 ma or 0-10 VDC analog output signal.
CM228-03, Page 1 952-935-4201, INC. (Fax) 952-935-9628 3947 MEADOWBROOK ROAD, MINNEAPOLIS, MN 55426 800-328-0738 CM3000 SIGNAL TRANSMITTER Introduction The MAXIGARD CM3000 is designed to convert shaft
More informationR8 Exhaust Installation Guidelines
STāSIS Engineering R8 Exhaust Installation Guidelines Exhaust Muffler support bracket bolt to muffler Muffler support bracket to chassis Muffler heat shield screws Heat shield bolt to chassis beneath anti
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/
INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4
More informationELECTRICAL. Contents - Wiring Diagrams
Contents - Wiring Diagrams T-Bar (Floating Deck - Hydro)............................................ 8-16 T-Bar (Fixed Deck - Gear)............................................... 8-17 T-Bar (Fixed Deck
More informationBX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler
Operator Manual & Installation Instructions ALLURE Tow Bar (10,000 lb) Pintle Coupler Hooking Up to Towed Vehicle 1. Position the towing vehicle on a level surface with a straight driveway ahead and engage
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationAIRTEK for Volvo Vehicles Single to Dual Height Control Valve Conversion Kit
Single to Dual Height Control Valve Conversion Kit SUBJECT: 60961-101 and 60961-102 LIT NO: 59310-026 DATE: January 2006 REVISION: A INTRODUCTION Prior to March 2005, some Volvo vehicle configurations
More informationQuik-Spec Coordination Panelboard
Read and retain for future reference Quik-Spec Coordination Panelboard Instruction Leaflet 3A1071 RevD Section TABLE OF CONTENTS Page Danger and warnings for installation of the equipment.............3-4
More informationCheck the wires going to the back of the computer, if the wires are secure and console will not start see step b.
ELECTRONIC TROUBLESHOOTING 1. PROBLEM: Console LED's will not light, console will not power up The bike must be pedaled at greater than 50 RPM while Check the wires going to the back of the computer, if
More informationTOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number
More informationWARNING Carefully Read These Instructions Before Use
DO NOT RETURN THIS SPRAYER TO STORE Call: 1-800-950-4458 Backpack Sprayer Use and Care Manual Manufactured for Northern Tool + Equipment Co., Inc. WARNING Carefully Read These Instructions Before Use Model
More information