NFPA501-A Seat Belt Monitoring System 2011 Ford F Series Crew Cab 6.2L, 6.7L, 6.8L

Size: px
Start display at page:

Download "NFPA501-A Seat Belt Monitoring System 2011 Ford F Series Crew Cab 6.2L, 6.7L, 6.8L"

Transcription

1 An ISO 9001:2008 Registered Company NFPA501-A Seat Belt Monitoring System 2011 Ford F Series Crew Cab 6.2L, 6.7L, 6.8L Introduction The NFPA501-A system acts as both a translator for chassis data as well as an input device for seat and seat belt sensors. All data collected either via OBDII (CAN) data stream or discretely from a sensor will be transmitted over a separate, proprietary InterMotive CAN network that adheres to the SAE J-1939 protocol. This will allow various Vehicle Data Recorders (VDR) from multiple manufacturers to simply read the NFPA501-A provided J1939 data without having to make significant changes to their VDR. The following are the specific chassis data provided by this translator: Accelerator Pedal Position - SPN91, PGN 0xF003 (61443) Engine RPM - SPN190, PGN 0xF004 (61444) Engine Coolant Temperature - SPN110, PGN 0xFEEE (65262) Transmission Fluid Temperature - SPN177, PGN 0xFEF8 (65272) Transmission Range - SPN163, PGN 0xF005 (61445) Engine Oil Pressure - SPN100, PGN 0xFEEF (65263) ABS State - SPN563, PGN 0xF001 (61441) Vehicle Speed - SPN84, PGN 0xFEF1 (65265) Parking Brake - SPN70, PGN 0xFEF1 (65265) Service Brake - SPN597, PGN 0xFEF1 (65265) Key Position - PGN 0xFEF1 (65265) VIN - SPN237, PGN 0xFEEC (65260) In addition, seat occupant / belt buckle status, along with optical warning system status are provided on the J1939 data stream for use with a Vehicle Data Recorder. The NFPA501-A acquires chassis data passively except during installation, so it will not interfere with other devices connected to the OBDII connector. Be sure the vehicle s battery is disconnected before proceeding with the installation. Installation Instructions Remove the lower dash panel below the steering column area and find a suitable location to mount the NFPA501-A module. Do not mount the module until all wire harnesses are routed and secure. (The last step of the installation is to mount the module). It is the installer s responsibility to route and secure all wiring harnesses where they cannot be damaged by sharp objects, mechanical moving parts and high heat sources. Failure to do so could result in damage to the system or vehicle and create possible safety concerns for the operator and passengers.

2 Data Link Harness (6-pin connector) Locate the vehicle s OBDII Data Link Connector. It will be mounted below the lower left dash panel. Remove the mounting screws for the OBDII connector. Plug the red connector from the NFPA501- A Data Link Harness into the vehicle s OBDII connector. Ensure the connection is fully seated and secure with the supplied wire tie. Mount the black connector from the Data Link Harness in the former location of the vehicle s OBDII connector. Leave the 6-pin Data Link connector unplugged from the 6-pin connector on the NFPA501-A module. NFPA501-A Translator Connection Output The NFPA501-A Data Link Harness has a 4-Pin White connector that provides J1939 data for connecting to a VDR. The pinout is as follows: Pin #1 Green Wire - J1939 CAN High. Pin #2 Red Wire - Battery Voltage. Pin #3 Blue Wire - J1939 CAN Low. Pin #4 Gray Wire - Ground. VDR Installation Install the VDR per manufacturer s instructions connecting the VDR J1939 signals to the 4 pin Data Link Harness connector. See pint out above. Use solder and heat shrink tubing to make these connections. Replacing the seatbelts - Red extended length Crew cab seat belts are part of the NFPA501-A kit. These will be used to replace the OEM seat belts front and rear. No belt is provided for the front center seat. Refer to Ford OEM service manuals for replacement details. The front and rear seats will need to be removed. Disconnect the large connector under the drivers seat to allow removal. Note that this connects to an airbag and pyrotechnic device contained inside the drivers seat. When replacing the seat belts and buckles (OEM driver buckle is not replaced) observe proper Ford OEM torque specs summarized below. (Note: Per Ford Motor Co. front seat bolts must be replaced when removed). Remove all seat belts and replace with the provided red NFPA seat belts. Observe location labels on the red seat belts which indicate the proper locations. Notes: The OEM driver s (left) buckle is NOT replaced, but is used by this system. Do NOT replace the seats until all harnesses have been installed. You can release the rear center seatbelt anchor by pushing in the latch using a straightened paper clip. Driver Front Center Front Rear Left Rear Center Rear Right Belt Assembly (all three bolts same) Not supported 30Nm (22ft-lbs) Buckle Assembly Do NOT remove Not supported 35Nm (26ft-lbs)

3 Installing the Seat Occupant Sensors Front Seats Invert front seats to expose serpentine springs and foam. Remove springs from their retainers and lay forward (Figure 5a). Place the 8.0 inch by 5.5 inch seat sensor and protective plastic guard between the seat springs and foam, with the plastic guard against the springs. Position it forward so the long side of the sensor meets the front metal pan. Sensor wires should exit toward the rear of the seat. Place four cable ties through the plastic guard holes and secure to the springs. Do not install front seats at this time. Front Metal Pan Rear Seats Fold rear seat bases up. Open the rear seat upholstery hook and loop at back to expose metal pan and foam. Place the 8.0 inch by 3.0 inch seat sensor and protective plastic guard between foam and metal pan, with the plastic guard against the metal pan and the long side in line with seat, as indicated in (Figure 5B), for each of the 3 rear seat positions. Exit sensor wires toward the rear of the seat. Close and reattach upholstery. Figure 5A Place Sensor Sensor Harness Installation Remove the front left kick panel below the left A-pillar. Figure 5B Remove the drivers side front and rear (under door) scuff plates. Harnesses will be routed under these. Starting from the rear right seat position, lay the rear seat portion of the sensor harness along the back wall toward the left side of the vehicle so the connector pairs are centered at each seat position. Lay the rear seat assembly in place, and connect each rear seat sensor and seat buckle sensor to the harness. Open the left side plastic cable enclosure that resides under the scuff panel. Continue laying the sensor harness forward in the plastic cable enclosure to beyond the B-pillar. Feed the front seat portion of the sensor harness under the carpet just behind the front seats toward the right of the vehicle.

4 Sensor Harness Installation Front Seats Feed the left front connector pair out of the carpet opening for the left floorboard vent under the driver seat. C311 Locate the C311 connector. (34-pin connector under the Driver s seat) connector Important: On the following wires use solder and heat shrink tubing to make all of the connections. Cut the C311 Pin #11 Green/Blue wire 1 from the connector. Attach the C311 Pin #11 Green/Blue harness side wire to the Purple blunt cut wire of the NFPA501-A Sensor Harness. Attach the C311 Pin #11 Green/Blue connector side wire to the Lt. Brown blunt cut wire of the NFPA501-A Sensor Harness. Cut the C311 Pin #12 Black wire 1 from the connector. Attach the C311 Pin #12 Black harness side wire to the Black blunt cut wire of the NFPA501-A Sensor Harness. Attach the C311 Pin #12 Black connector side wire to the Gray blunt cut wire of the NFPA501-A Sensor Harness. Feed the right front connector pair out of the carpet opening for the right floorboard vent under the passenger seat. Connect the respective sensor connectors to the harness. Continue laying the sensor harness forward in the plastic cable enclosure to the A-pillar. Feed the sensor harness upward, either along the A-pillar or forward of the park brake, to the left side vent panel. (Figure 6, detail 2). If the park brake route is selected ensure the harness does not interfere or entangle in the park brake mechanism. Finish harness placement so the two end connectors are accessible at opening below the vent at the left side vent panel. Adjust the harness as necessary so the wires are not pulled too tight. Tuck the harness into the floor at the rear wall (behind the rear seat). Close the plastic enclosures under the scuff panels. Reinstall the front seats. Torque seat mounting bolts to 70Nm (52 ft-lbs). Note: Front seat bolts must be replaced when removed, per Ford Motor Co. Technical Information. Connect the front seat sensors and seat belt switches to the NFPA501-A Sensor Harness. Reconnect the C311 connector halves. Reinstall the front left kick plate. Reinstall scuff plates. Figure #6

5 Warning Beeper Installation Find an appropriate location for mounting the warning beeper. Some vehicles have a vertical bracket just in front of the 4WD floor shifter which works well as a mounting bracket. Attach the 4 Pin Warning Beeper harness to the NFPA501-A Module s 4-Pin white connector. Attach the 12-Pin connector Pin #12 Orange wire to the Positive side (red painted terminal) of the Warning Beeper. LED Display Panel Installation Some upfitters simply leave the display connected, but un-mounted to allow the final stage manufacturer and all optional equipment such as radio s are installed. Suggested locations include the dash board within view of the driver and the front passenger (captain position), which must be able to see the LED panel should a laptop or other additional equipment is place on or at the center console. A common location is the space below the left A/C vent. The length of the display harness is 40. This is the maximum distance the display can be mounted from the NFPA501-A module. Attach the 4 Pin LED display harness to the NFPA501-A Module s 4-Pin Black connector. Attach the other end of the display harness to the LED Display Panel. Sensor Harness Connection Connect the sensor harness 10 pin connector to the NFPA501-A module. Connect the sensor harness 12 pin connector to the NFPA501-A module. Reconnect the battery Initial Installation Power-Up from factory: With the key ON and engine OFF, plug in the 6-pin Data Link harness connector to the white 6-pin connector on the NFPA501-A module. This "Hard Boot" will cause the module to go into a special "Install Routine". This routine runs functions that will assure the module is configured properly to the vehicle in which it is installed: 1. CAN detect: First, the module auto-detects the vehicle CAN communication network to verify it can read vehicle data. If the module fails to detect the CAN bus, module LED6 will turn ON and LEDs 1-4 will scroll. In addition, the far right 2 sets of LEDs (top & bottom row) on the external display will be "rotating". The module will not function if this happens. The most likely problem in this case is something wrong with either the vehicle OBDII connection or in the harness connecting to the module.

6 Initial Installation Power-Up (Continued) 2. Seat Selection: The module will try to establish which seat positions are active in the vehicle. It does this by reading seat belt sensors. The driver's seat is always enabled, but all other positions (4) can be set active or inactive to allow for custom configurations. If inactive, they will neither be displayed nor reported (to the VDR). In order for a specific position to be sensed and therefore deemed "active", it needs a proper harness connection to the module, and additionally the seat belt must be unbuckled. Make sure all positions that need to be active are set up this way prior to running the install routine. If there is ever a need to disable one or more seat positions, all that is needed is to plug in the belt of the seat to be deactivated prior to running the install routine. Having no Yellow Status LED buckle connection to the harness will give the same result. Once the seat selection is complete, the module will "flash out" the seat configuration using module LEDs 1-5. The LEDs will blink several times indicating (by being ON) which positions are active. Seats are represented as follows: LED1 Driver LED3 Rear Left LED5 Rear Right LED2 Front Right LED4 Rear Middle As stated above, the seat selection routine runs automatically the first time (from the factory) power is applied to the module. If seat selection is ever needed at a later time, a "special hard boot" needs to be run. To do this, make and hold a ground connection to the module test pad while plugging it in with the key on. The module will "see" this and run the seat selection routine. If seat selection fails, module LED7 will turn ON and LEDs 1-4 will scroll. If you see this indication, the problem is most likely the module itself. Contact Intermotive Technical Support VIN Capture: The first time (from the factory) the module is plugged in, it will try to read the vehicle VIN. It needs this to assure that vehicle data will be correctly received and interpreted. If it cannot acquire the VIN or if the acquired VIN is invalid, the module yellow Status LED will flash, and the external display LEDs will "dance". If VIN acquisition was successful, the module stores and uses it for future reference. If VIN cannot be acquired, the module will not function; contact Intermotive Technical Support Post Installation Test With vehicle in Park, Parking Brake applied, and Key OFF (module asleep): Turn Key ON. Verify all Display Panel LEDs come on together briefly (prove out). Sit in each seat location, and verify respective red LED illuminates on the panel. While sitting in the seat, buckle the seat belt, and verify red LED goes out and the green LED illuminates. While sitting in a seat (seat belt unbuckled, vehicle in Park, and Park Brake applied): Move transmission selector out of Park position, and verify audible beeper activates. Press Silence button (on Display Panel), and verify beeper stops. Shift back into Park position. Leave the seat for 3 sec, then sit back down again. This resets the alarm function. Release park brake, and verify audible beeper activates. Buckle seatbelt, and verify the beeper stops. Turn key off. If the system fails any step in the Post Installation Test, review the installation instructions and check all connections. If necessary, call InterMotive technical (530)

7 An ISO 9001:2008 Registered Company NFPA/Seat Belt Monitor NFPA501-A 2011 Ford F Series Crew Cab 6.2L, 6.7L, 6.8L Operating Instructions (leave in vehicle) The NFPA501-A system monitors up to five seats in a crew cab vehicle to ensure the occupants have their seat belts properly buckled. It flashes a red indicator identifying seat positions which are not buckled, and sounds a warning beeper. It requires the seat to be occupied before the belt is buckled to discourage spoofing the system. It also translates and sends vehicle chassis data, along with seat belt data to an optional Vehicle Data Recorder. Silence Button Left Front Seat Right Front Seat Left Rear Seat Center Rear Seat Right Rear Seat Operational Notes: When the key is turned on, all Display Panel LEDs will blink on briefly as a test. Sitting in each seat location will illuminate the respective Red LED on the panel. When sitting in an unbelted seat, moving the transmission selector out of the Park position will sound the beeper. Also when sitting in an unbelted seat, releasing the park brake will sound the beeper. Inserting the seatbelt into the buckle while sitting in each seat will illuminate the respective Green LED and the extinguish the respective Red LED. Inserting the seatbelt into the buckle without sitting in the seat will flash the respective Red LED. Removing the buckle from the seatbelt of the unoccupied seat will stop the beeper. Pressing the Silence button anytime the beeper is sounding will stop the beeper for that seat only. For technical support, call (530) NFPA501-A-02-OP

8 Submit product registration at If the NFPA 501-A fails any step in the System Operation Test, review the installation instructions and check all connections. If necessary, call InterMotive technical (530) NFPA501-A-02-CAD

Aftermarket Interface Module

Aftermarket Interface Module An ISO 9001:2008 Registered Company Aftermarket Interface Module (2015-2018 Ford Transit) AIM514-B High Side Solenoid type Coolant Valve Control AIM515-B Motor Reversing type Coolant Valve Control Introduction

More information

RCMP501-A Selective Chime Mute Module Ford Police Interceptors (Sedan and Utility)

RCMP501-A Selective Chime Mute Module Ford Police Interceptors (Sedan and Utility) An ISO 9001:2008 Registered Company RCMP501-A Selective Chime Mute Module 2013-2015 Ford Police Interceptors (Sedan and Utility) Introduction The RCMP501-A module aids in covert operations by selectively

More information

A-1939CM550-AP J1939 Translator Ford F53/F59

A-1939CM550-AP J1939 Translator Ford F53/F59 An ISO 9001:2008 Registered Company A-1939CM550-AP J1939 Translator 2016-2017 Ford F53/F59 Introduction The A-1939CM550-AP translator plugs into a vehicle s OBDII connector and acquires proprietary vehicle

More information

Idle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications

Idle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications An ISO 9001:2008 Registered Company Idle Timer Controller - ITC515-A 2015-2018 Ford Transit Contact InterMotive for additional vehicle applications Overview The ITC515-A system will shut off gas or diesel

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company An ISO 9001:2008 Registered Company Introduction Engine Monitor System 2009-2018 Ford E Series (EMS501-D) 2008-2010 Ford F250-550 6.2L, 6.8L (EMS506-D) 2011-2016 Ford F250-550 6.2L, 6.8L (EMS507-D) 2017

More information

Intelligent Lift Interlock ILISCT511-A (Manual Lift Door) Ford Transit Connect

Intelligent Lift Interlock ILISCT511-A (Manual Lift Door) Ford Transit Connect An ISO 9001:2000 Registered Company Intelligent Lift Interlock ILISCT511-A (Manual Lift Door) 2010-2013 Ford Transit Connect Introduction The ILISCT511 is a microprocessor driven system for controlling

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company Introduction An ISO 9001:2008 Registered Company 1939CM405-A J1939 Translator (for use with GTWY505/506/605, and HL510/550/610) 2005-2017 Ford E-Series & F250-F550 2014-2017 Ford Transit 2006-2017 Chevy

More information

ITCEMS950 Idle Timer Controller - Engine Monitor Shutdown Isuzu NPR 6.0L Gasoline Engine

ITCEMS950 Idle Timer Controller - Engine Monitor Shutdown Isuzu NPR 6.0L Gasoline Engine Introduction An ISO 9001:2008 Registered Company ITCEMS950 Idle Timer Controller - Engine Monitor Shutdown 2014-2016 Isuzu NPR 6.0L Gasoline Engine Contact InterMotive for additional vehicle applications

More information

Idle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750

Idle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750 An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC520-A 2009-2018 Ford E Series 2008-2016 Ford F250 - F550 2017-2018 Ford F250 - F550 (*B-ITC520-A) 2016-2018 F650/F750 *Uses the Ford 24-Pin

More information

HL515-B Fast Idle, Lift Interlock Ford Transit

HL515-B Fast Idle, Lift Interlock Ford Transit An ISO 9001:2008 Registered Company HL515-B Fast Idle, Lift Interlock 2015-2018 Ford Transit Introduction The HighLock 515-B is a wheelchair lift safety interlock which will only work with the ignition

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company An ISO 9001:2008 Registered Company CVC501-A HVAC & Fast Idle CAN Vehicle Controller CVC502-A HVAC Control without Fast Idle 2011-2016 Ford F250-F550 (CVC501/502-A) 2017 Ford F-250-F550 (B-CVC501/502-A)

More information

AFIS515VSX-B Fast Idle System Ford Transit 2015 American General MV-1 3.7L Engine

AFIS515VSX-B Fast Idle System Ford Transit 2015 American General MV-1 3.7L Engine An ISO 9001:2008 Registered Company AFIS515VSX-B Fast Idle System 2015-2018 Ford Transit 2015 American General MV-1 3.7L Engine Introduction The AFIS515VSX-B is a Fast Idle system that elevates engine

More information

GTWY505 Fast Idle, Shift Interlock, I/O Ford E-Series

GTWY505 Fast Idle, Shift Interlock, I/O Ford E-Series An ISO 9001:2008 Registered Company GTWY505 Fast Idle, Shift Interlock, I/O 2009-2018 Ford E-Series Introduction The Gateway 505 is a wheelchair lift safety interlock which will only work with the ignition

More information

Idle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana

Idle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana Introduction An ISO 9001:2015 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2019 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications The A-ITC620-A1 is an

More information

GTWY515, GTWY516* Fast Idle, Shift Interlock, I/O Ford Transit Introduction

GTWY515, GTWY516* Fast Idle, Shift Interlock, I/O Ford Transit Introduction An ISO 9001:2015 Registered Company GTWY515, GTWY516* Fast Idle, Shift Interlock, I/O 2015-2019 Ford Transit Introduction The Gateway 515 and 516 are wheelchair lift safety interlocks which allows lift

More information

Idle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana

Idle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2018 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications Introduction The A-ITC620-A1 is an

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company Introduction An ISO 9001:2008 Registered Company 1939CM401-A J1939 Translator (harness compatible with GTWY401 and HL201) 2005-2017 Ford E-Series & F250-F550 2014-2017 Ford Transit 2006-2017 Chevy Express,

More information

ILISC515-A Shift Interlock (Manual Lift Door) Ford Transit

ILISC515-A Shift Interlock (Manual Lift Door) Ford Transit An ISO 9001:2008 Registered Company ILISC515-A Shift Interlock (Manual Lift Door) 2015-2018 Ford Transit Introduction The ILISC515-A is a microprocessor driven system for controlling wheelchair lift operation.

More information

Idle Timer Controller - ITC Freightliner MT45 Contact InterMotive for additional vehicle applications

Idle Timer Controller - ITC Freightliner MT45 Contact InterMotive for additional vehicle applications An ISO 9001:2008 Registered Company System Operation Idle Timer Controller - ITC805 2013-2018 Freightliner MT45 Contact InterMotive for additional vehicle applications The ITC805 system shuts down idling

More information

GTWY605 Fast Idle, Shift Interlock, I/O Chevy 610 Van - 6.0L and 6.6L Engines Contact InterMotive for additional vehicle applications.

GTWY605 Fast Idle, Shift Interlock, I/O Chevy 610 Van - 6.0L and 6.6L Engines Contact InterMotive for additional vehicle applications. An ISO 9001:2008 Registered Company GTWY605 Fast Idle, Shift Interlock, I/O 2009-2017 Chevy 610 Van - 6.0L and 6.6L Engines Contact InterMotive for additional vehicle applications. Introduction The Gateway

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company Introduction An ISO 9001:2008 Registered Company GTWY506 Fast Idle, Shift Interlock, I/O 2011-2016 Ford F250-F550 2017 Ford F250-F550 (Uses the Ford 24-Pin Data Link Harness) 2016-2017 Ford F650/750* *Transmission

More information

Speed Sentinel II Programmable Road Speed Limiter

Speed Sentinel II Programmable Road Speed Limiter An ISO 9001:2008 Registered Company Speed Sentinel II Programmable Road Speed Limiter SS501-A, SS501-AX Ford E Series 2005-2008 Ford F250-F550 Series 2008-2010 Ford Crown Victoria 2005-2008 Contact InterMotive

More information

An ISO 9001:2015 Registered Company

An ISO 9001:2015 Registered Company Introduction An ISO 9001:2015 Registered Company HL550-B Fast Idle, Lift Interlock 2011-2016 Ford F250-F550 2017-2019 Ford F250-F550 (B-HL550*) 2016-2017 Ford F650/750** *Uses the Ford 24-Pin Data Link

More information

C-IDLE750 Idle-Lock Anti-Theft 2018 RAM Contact InterMotive for additional vehicle applications.

C-IDLE750 Idle-Lock Anti-Theft 2018 RAM Contact InterMotive for additional vehicle applications. An ISO 9001:2008 Registered Company C-IDLE750 Idle-Lock Anti-Theft 2018 RAM 2500-5500 Contact InterMotive for additional vehicle applications. Introduction Idle-Lock is an anti-theft system that allows

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company Overview An ISO 9001:2008 Registered Company AFIS422VSX-B Advanced Fast Idle System - Transit Application 2009-2017 Ford E-Series, all engines 2009-2010 Ford F-250 - F-550, all engines 2014-2018 Ford F53/F59,

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company An ISO 9001:2008 Registered Company IDLE6xx Idle Lock Anti-Theft 2015-2016 Chevy Tahoe (IDLE601) 2015-2016 Chevy Silverado (IDLE601) 2017-2018 Chevy Tahoe (IDLE654) 2017-2018 Chevy Silverado (IDLE654)

More information

HL610-B Fast Idle, Lift Interlock Chevy 610 Van 6.0L and 6.6L Contact InterMotive for additional vehicle applications

HL610-B Fast Idle, Lift Interlock Chevy 610 Van 6.0L and 6.6L Contact InterMotive for additional vehicle applications An ISO 9001:2015 Registered Company HL610-B Fast Idle, Lift Interlock 2009-2019 Chevy 610 Van 6.0L and 6.6L Contact InterMotive for additional vehicle applications Introduction The HighLock 610 is a wheelchair

More information

BOM560-BC Black Out Module Ford Interceptor Utility Contact InterMotive for additional applications

BOM560-BC Black Out Module Ford Interceptor Utility Contact InterMotive for additional applications An ISO 9001:2008 Registered Company BOM560-BC Black Out Module 2016-2018 Ford Interceptor Utility Contact InterMotive for additional applications Introduction The BOM560-BC module has the ability to eliminate

More information

SMM601-B Surveillance Mode Module Chevy Tahoe SSV and PPV (U.S. Vehicle Only) 2017* Chevy Tahoe PPV Only (U.S.

SMM601-B Surveillance Mode Module Chevy Tahoe SSV and PPV (U.S. Vehicle Only) 2017* Chevy Tahoe PPV Only (U.S. An ISO 9001:2008 Registered Company SMM601-B Surveillance Mode Module 2015-2016 Chevy Tahoe SSV and PPV (U.S. Vehicle Only) 2017* Chevy Tahoe PPV Only (U.S. Vehicle Only) * The SMM601 will only work properly

More information

PIM701 (Police Interface Module) Dodge Charger Pursuit

PIM701 (Police Interface Module) Dodge Charger Pursuit An ISO 9001:2008 Registered Company PIM701 (Police Interface Module) 2015-2017 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired

More information

Speed Sentinel Programmable Road Speed Limiter

Speed Sentinel Programmable Road Speed Limiter An ISO 9001:2008 Registered Company Speed Sentinel Programmable Road Speed Limiter SS531-A, SS531-AX, SS531-AND Ford E Series 2005-2012 Ford F Series 2008-2010 Ford Crown Victoria 2005-2008 Contact InterMotive

More information

ECO3-601/602 EcoStar III * Chevy Express/GMC Savana Contact Intermotive for additional vehicle applications

ECO3-601/602 EcoStar III * Chevy Express/GMC Savana Contact Intermotive for additional vehicle applications An ISO 9001:2015 Registered Company ECO3-601/602 EcoStar III 2009-2019* Chevy Express/GMC Savana Contact Intermotive for additional vehicle applications * In 2017-2018, the ignition switches on Chevy Express

More information

BOM505 Black Out Module Ford F-150 Contact InterMotive for additional applications

BOM505 Black Out Module Ford F-150 Contact InterMotive for additional applications An ISO 9001:2008 Registered Company BOM505 Black Out Module 2015-2016 Ford F-150 Contact InterMotive for additional applications Introduction The BOM505 module has the ability to eliminate all exterior

More information

C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit

C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit An ISO 9001:2008 Registered Company C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired functions

More information

IDG701 (IdleGuard ) Dodge Charger Pursuit

IDG701 (IdleGuard ) Dodge Charger Pursuit An ISO 9001:2008 Registered Company IDG701 (IdleGuard ) 2016-2018 Dodge Charger Pursuit Introduction Dodge Charger Pursuit vehicles are all equipped with the Secure Park feature, which locks the column

More information

ILISP610-A Shift Interlock Chevy/GMC Full Size Van Chevy/GMC Full Size Van L Contact InterMotive for specific applications

ILISP610-A Shift Interlock Chevy/GMC Full Size Van Chevy/GMC Full Size Van L Contact InterMotive for specific applications An ISO 9001:2008 Registered Company ILISP610-A Shift Interlock Chevy/GMC Full Size Van 2008-2018 Chevy/GMC Full Size Van 2008-2015 4.6L Contact InterMotive for specific applications Introduction The ILISP610-A

More information

BOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications

BOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications An ISO 9001:2008 Registered Company BOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications Introduction The BOM507-BC module has the ability to eliminate all exterior

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company An ISO 9001:2008 Registered Company BOM620-B Black Out Module 2017 Chevy Silverado SSV (U.S. Vehicles Only) 2017 Chevy Tahoe SSV (U.S. Vehicles Only) Contact InterMotive for additional applications Introduction

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company Introduction An ISO 9001:2008 Registered Company BOM620-C Black Out Module 2017, 2018 Chevy Silverado (SSV & non SSV U.S. Vehicles Only) 2017-2018 Chevy Tahoe SSV (U.S. Vehicles Only) 2018 Chevy Tahoe

More information

GRD502-B Flow Chart 02/05/09

GRD502-B Flow Chart 02/05/09 PINPOINT TEST A: NO PROVE OUT OF ANY LEDs prove out (all LED's light up) of the LED's when module power is applied or module "wakes up", indicates that: - the Guardian module does not have power. - the

More information

An ISO 9001:2008 Registered Company

An ISO 9001:2008 Registered Company An ISO 9001:2008 Registered Company BOM601-B Blackout Module 2015-2016 Chevy Tahoe SSV and PPV (U.S. Vehicles Only) 2017* Chevy Tahoe PPV Only (U.S. Vehicle Only) 2016 Silverado SSV (U.S. Vehicles Only)

More information

SYSTEM OPERATION IMPORTANT CAUTIONS

SYSTEM OPERATION IMPORTANT CAUTIONS SYSTEM OPERATION The system is turned on by placing the gear shift lever in the reverse position. The green light on the cab Control Box will illuminate to indicate the system is operating. When an object

More information

PART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)

PART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:

More information

Installation Instructions TRACKNET TN-4003/4004

Installation Instructions TRACKNET TN-4003/4004 Installation Instructions TRACKNET TN-4003/4004 TABLE OF CONTENTS TABLE OF CONTENTS Introduction... 2 Installation Caution and Warnings... 3 Control Module and Components... 3-4 Mounting Location...4-5

More information

HAWK401-A Reverse Assistance System

HAWK401-A Reverse Assistance System An ISO 9001:2008 Registered Company HAWK401-A Reverse Assistance System Introduction The HAWK401-A Reverse Assistance System is an ultrasonic distance monitoring system. When the vehicle is in reverse,

More information

Accessory Fuse Block. Please read this entire manual before proceeding with installation.

Accessory Fuse Block. Please read this entire manual before proceeding with installation. Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails

More information

PART NUMBER: H630SXC001. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)

PART NUMBER: H630SXC001. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Interface / Power Harness (1) C. Cable tie (8) F. Mounting Nuts (2) G. Replacement Front Speaker (2) H. Badge mounting

More information

TIP SHEET. Installation Tips for SP-404/SP EVO-ALL + SPDT Remote Start/Alarm T1642

TIP SHEET. Installation Tips for SP-404/SP EVO-ALL + SPDT Remote Start/Alarm T1642 TIP SHEET Installation Tips for SP-404/SP-502 + EVO-ALL + SPDT Remote Start/Alarm T1642 Nissan Armada: 2008-2012 Nissan Cube: 2009-2012 Nissan Frontier: 2008-2012 Nissan Pathfinder: 2009-2012 Nissan Quest:

More information

Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013

Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior

More information

Guardian GRD501-AR Adapter Matrix

Guardian GRD501-AR Adapter Matrix An ISO 9001:2008 Registered Company Guardian GRD501-AR Adapter Matrix Note: Based on vehicle age and transmission code, it may be necessary to use one of the adapters listed below along with the GRD501

More information

Conflicts. Camry L (ECO Grade) Security System with Keyless Entry. Part Number: Accessory Code: QK1

Conflicts. Camry L (ECO Grade) Security System with Keyless Entry. Part Number: Accessory Code: QK1 2013- Part Number: 00016-32905 Accessory Code: QK1 Conflicts Note: NOT FOR INSTALLATION ON VEHICLES WITH FACTORY THEFT DETERRENT SYSTEMS. Kit Contents Item # Quantity Reqd Description 1 1 Keyless Security

More information

TIP SHEET T0937. Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT

TIP SHEET T0937. Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT TIP SHEET T0937 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself installers

More information

PFSDC12. Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Stillwater Designs PFSDC12-A Subwoofer Enclosure

PFSDC12. Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Stillwater Designs PFSDC12-A Subwoofer Enclosure PFSDC12 Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Subwoofer Enclosure Amplifier/Bracket Assembly Subwoofer Power Harness Amplifier Harness Subwoofer Harness Amplifier Power Harness

More information

Gateway 505/605 Symptom Flow Chart Lift Interlock

Gateway 505/605 Symptom Flow Chart Lift Interlock An ISO 9001:2008 Registered Company Gateway 505/605 Symptom Flow Chart Lift Interlock Begin diagnosis by performing the system post installation instructions notating system operation while doing checks.

More information

Installation Tips - (Crimestopper RS1/RS2) & (Fortin EVO-ALL 5): *regular key & automatic transmission only*

Installation Tips - (Crimestopper RS1/RS2) & (Fortin EVO-ALL 5): *regular key & automatic transmission only* Installation Tips - (Crimestopper RS1/RS2) & (Fortin EVO-ALL 5): TIP SHEET T3385f, T3413f *regular key & automatic transmission only* Thank you for purchasing your remote start from MyPushcart.com - an

More information

Installation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( FIT), ( Pilot), ( Ridgeline) Acura: ( MDX)

Installation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( FIT), ( Pilot), ( Ridgeline) Acura: ( MDX) Installation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( 06-08 FIT), ( 05-08 Pilot), ( 06-13 Ridgeline) Acura: ( 03-06 MDX) TIP SHEET T0777 Thank you for purchasing your remote start from

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 501-20B-1 REMOVAL AND INSTALLATION 501-20B-1 Occupant Classification Sensor Item Part Number Description 7 61704 Seat track assembly Special Tool(s) 8 Safety belt buckle switch electrical connector (part

More information

2000 DODGE DURANGO INSTALLATION INSTRUCTIONS KIT #60053

2000 DODGE DURANGO INSTALLATION INSTRUCTIONS KIT #60053 WARNING This body lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the

More information

Paddle Shifter User s Guide

Paddle Shifter User s Guide Paddle Shifter User s Guide Included Parts List: 1 - Receiver Module 1 - Receiver Module Harness (5 length) 1 - Paddle Shifter Module 1 - Paddle Shifter Module Harness 1 ½ Spacer 2 ¼ Spacer 1 User s Guide

More information

Installation Tips for your Remote Start/Keyless Entry (for Mazda Vehicles) v3.1 Updated 9/22/2012

Installation Tips for your Remote Start/Keyless Entry (for Mazda Vehicles) v3.1 Updated 9/22/2012 Installation Tips for your Remote Start/Keyless Entry (for Mazda Vehicles) v3.1 Updated 9/22/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote

More information

Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles)

Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself

More information

Gentex by VOXX Corporation Installation Instructions

Gentex by VOXX Corporation Installation Instructions KIT CONTENTS: Item Qty Part Number Description 1 1: ADVGEN20A 7 Pin Auto-Dimming Mirror with Compass and Temperature 2 1 Gentex by VOXX Corporation Installation Instructions Contact VOXX Customer Service

More information

TIP SHEET. Installation Tips for your RS IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14. 1 P a g e

TIP SHEET. Installation Tips for your RS IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14. 1 P a g e Installation Tips for your RS-150 + IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14 TIP SHEET Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts

More information

Gentex Homelink Installation Instructions

Gentex Homelink Installation Instructions Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following

More information

WOT Box Installation Instructions VW / Audi

WOT Box Installation Instructions VW / Audi Connector Pinout Pin Color AWG Name WOT Box Installation Instructions VW / Audi Description 1 Yellow 18 RPM Connect to Fuel Injector Drive Signal or Ignition Control Signal (varies by car model) 2 Black

More information

ROADRELAY 5 Installation Guide

ROADRELAY 5 Installation Guide ROADRELAY 5 Installation Guide ROADRELAY 5 Installation Guide Bulletin No. 4971214 Revision A Copyright 2011, Cummins Inc. All rights reserved. Cummins Inc. shall not be liable for technical or editorial

More information

Installation Tips for your Remote Start/Keyless Entry (for Ford Vehicles) v3.3 Updated 1/13/2013

Installation Tips for your Remote Start/Keyless Entry (for Ford Vehicles) v3.3 Updated 1/13/2013 Installation Tips for your Remote Start/Keyless Entry (for Ford Vehicles) v3.3 Updated 1/13/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote

More information

Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.c) + 2 diodes

Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.c) + 2 diodes Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.c) + 2 diodes TIP SHEET T3093 + T3103 FOR: NISSAN ( 09-14 Cube), ( 11-14 Juke), & ( 07-11 Versa) automatic, regular key vehicles Thank you for purchasing

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description

More information

TOYOTA TUNDRA TVIP V4 Preparation

TOYOTA TUNDRA TVIP V4 Preparation Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM

More information

P/N S Tools Needed: Directions:

P/N S Tools Needed: Directions: P/N S197-850 2005-09 Illuminated Start Button Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the installation. A factory shop manual should be available

More information

Guardian GRD502-A Adapter Matrix

Guardian GRD502-A Adapter Matrix Guardian GRD502-A Adapter Matrix Note: Based on vehicle age and transmission code, it may be necessary to use one of the adapters listed below along with the GRD501 or GRD502 part number. Adapter Application

More information

PF150SC15. Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Stillwater Designs PF150SC15-A

PF150SC15. Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Stillwater Designs PF150SC15-A PF150SC15 Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs PF150SC15-A2-20160502

More information

Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.b)

Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.b) Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.b) TIP SHEET T3092 + T3102 FOR: NISSAN ( 08-14 Frontier), ( 08-12 Pathfinder), & ( 08-12 Xterra) Thank you for purchasing your remote start from MyPushcart.com

More information

Covers All 430, 440, 441 and CJ Series Advanced Security Systems.

Covers All 430, 440, 441 and CJ Series Advanced Security Systems. INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with

More information

INTERNATIONAL 3200 AND Freightliner MB

INTERNATIONAL 3200 AND Freightliner MB An ISO 9001:2000 Registered Company INTERNATIONAL 3200 AND Freightliner MB55 2002-2008 Intelligent Lift Interlock System (ILIS701-D) - Installation Instructions International & MB45/55 w/allison 2000 and

More information

RS4 / RS7 + (4) + SPDT

RS4 / RS7 + (4) + SPDT TIP SHEET Installation Tips for RS4 / RS7 + Honda-SL3 (4) + SPDT + Diode x2 T0776, T0731 Honda: ( 08-12 Accord), ( 12-13 Civic), 12-13 CRV), ( 11-13 Odyssey), ( 09-13 Pilot) Acura: ( 09-13 TSX) Thank you

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness

More information

Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System. M6 Bolt X 2

Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System. M6 Bolt X 2 SF150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System Subwoofer Assembly Amplifier Relocation Bracket (not used on non Sony trucks)

More information

REARSENTRY TM BASE KIT ROSTRA OBSTACLE SENSING SYSTEM CONTENTS

REARSENTRY TM BASE KIT ROSTRA OBSTACLE SENSING SYSTEM CONTENTS REARSENTRY TM ROSTRA OBSTACLE SENSING SYSTEM BASE KIT 250-1728 CONTENTS Parts List... 2 Parts Diagrams... 2 Before You Start... 5 Installation... 7 Troubleshooting Guide...11 Form #4713, Rev. B, 01-07-04

More information

* * APPLICABLE MODELS: 2016 > CX-3

* * APPLICABLE MODELS: 2016 > CX-3 PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart

More information

PN CHEVY TRI-FIVE. Kit Contents: Four panel Sequential LED Taillight kit installation guide

PN CHEVY TRI-FIVE. Kit Contents: Four panel Sequential LED Taillight kit installation guide Four panel Sequential LED Taillight kit installation guide Kit Contents: 2 tail light LED panels 2 tail light turn signal LED panels 1 rubber boot/sleeve kit 1 power wire with t-tap 1 driver side LED harness,

More information

TIP SHEET T0937. Installation Tips for RS00 + Passlock-sl2(4) + SPDT

TIP SHEET T0937. Installation Tips for RS00 + Passlock-sl2(4) + SPDT Installation Tips for RS00 + Passlock-sl2(4) + SPDT TIP SHEET T0937 Chevrolet (Astro 1998-2005) (Avalanche 2002-2006) (Blazer 1998-2005) (Express Van 1998-2007) (Impala 2000-2005) (Monte Carlo 2000-2005)

More information

Ford Econoline

Ford Econoline Guardian Lift Interlock (GRD0-BB) Installation Instructions Ford Econoline 009-00 It is not necessary to cut any Ford wires during the installation of the Guardian wire harnesses. Always disconnect the

More information

TIP SHEET T2352, T3396. Installation Tips for RS1 + EVO-ALL 1-BUTTON REMOTE STARTER FOR: Acura RDX PUSH-TO-START / AUTOMATIC

TIP SHEET T2352, T3396. Installation Tips for RS1 + EVO-ALL 1-BUTTON REMOTE STARTER FOR: Acura RDX PUSH-TO-START / AUTOMATIC Installation Tips for RS1 + EVO-ALL 1-BUTTON REMOTE STARTER FOR: Acura RDX 2013-2015 PUSH-TO-START / AUTOMATIC TIP SHEET T2352, T3396 Thank you for purchasing your remote start from MyPushcart.com - an

More information

INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT

INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT PART NUMBER: 0000-89-N30 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT APPLICABLE MODELS: 2016 > CX-9 PACKAGE CONTENTS: INSTALLATION INSTRUCTIONS QTY 1 CABLE TIE MOUNT QTY

More information

ECT Display Driver Installation for AP2 Module

ECT Display Driver Installation for AP2 Module ECT Display Driver Installation for AP2 Module Overview The ECT Display Driver is a small module with a removable wire harness that mounts behind the driver's foot well cover. All wiring connections are

More information

R-SE JK 4 DOOR Step Slider Install Instructions. *If any parts listed are missing or damages please call prior to install.

R-SE JK 4 DOOR Step Slider Install Instructions. *If any parts listed are missing or damages please call prior to install. R-SE JK 4 DOOR Step Slider Install Instructions Parts List: 1 Divers side slider assembly 1 Passenger side slider assembly 1 wiring harness 1 control box 2 spacers 2 LED lights (optional) 10 SS Button

More information

LCI Motorized Leveling - Unidirectional (2009-Present)

LCI Motorized Leveling - Unidirectional (2009-Present) LCI Motorized Leveling - Unidirectional (2009-Present) OWNER'S MANUAL Rev: 07.09.2018 LCI Motorized Leveling (2009 - Present) Owner's Manual TABLE OF CONTENTS SYSTEM 3 Prior to Operation 3 System Description

More information

PRAMCQ13. Designed for Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles

PRAMCQ13. Designed for Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles PRAMCQ13 Designed for 2013 2017 Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles Subwoofer Alternate Amplifier Bracket Amplifier Subwoofer Harness Subwoofer Amplifier

More information

Wired Real Time GPS Installation Instructions

Wired Real Time GPS Installation Instructions Wired Real Time GPS Installation Instructions This page intentionally left blank. TABLE OF CONTENTS 1. Introduction 2 2. Selecting the Mounting Location for the Device. 3 3. Mounting the Device 5 4. Optional

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:

More information

Essentials. Simple and Easy to Follow Installation Manual % Free Call! Expert Advice.

Essentials. Simple and Easy to Follow Installation Manual % Free Call! Expert Advice. Essentials Simple and Easy to Follow Installation Manual % Free Call! %800-745-5337 Expert Advice DVD Headrest JK Wrangler Installation Instructions Note: Be sure to read this entire instruction sheet

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Sedan (2013+) PART NUMBER: 999F4 AX010 - Universal Security Lighting Kit. KIT CONTENTS: Item QTY

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS OEM Tailgate Camera/Bezel Assembly with Chassis Harness 2014-current Chevrolet Silverado and GMC Sierra (Kit part number 9002-1005) Kit Contents: Chassis Harness 1 bubble bag containing: Tailgate Handle

More information

Installation Tips for your Add-on Remote Start (for GM vehicles with INTSL Install 2) v3.2 Updated 11/12/2012

Installation Tips for your Add-on Remote Start (for GM vehicles with INTSL Install 2) v3.2 Updated 11/12/2012 Installation Tips for your Add-on Remote Start (for GM vehicles with INTSL Install 2) v3.2 Updated 11/12/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing

More information

Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14

Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Thank you for purchasing your remote start from MyPushcart.com - an industry

More information

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:

More information

Installation instructions, accessories - Bluetooth, Mute kit XC / Volvo Car Corporation Göteborg, Sweden

Installation instructions, accessories - Bluetooth, Mute kit XC / Volvo Car Corporation Göteborg, Sweden XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 0.5/1.1 2006 11 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008, XC90 2009, XC90 2010 Page 1 of 15 Required tools A0000162 IMG-242205

More information