SHP90 Introductory Orientation

Size: px
Start display at page:

Download "SHP90 Introductory Orientation"

Transcription

1 SHP90 Introductory Orientation Introduction I. Walk-Around A. General Features & Terminology B. Material Flow through Machine II. III. Cab & Controls A. Cab Features B. Seat Adjustments C. Seat Mounted Controls D. Steering Column E. Gauge Panel F. Switch Panel Operation & Procedures A. Daily Inspection B. Starting Machine C. Getting Ready to Harvest 1. Initial settings 2. Bulk harvest mode 3. Sample harvest mode D. Clean out Features 1. Threshing cylinder reverser 2. Venturi access doors 3. Air delivery system 4. Unload auger door E. Unloading 1. Grain tank 2. Bag tank F. Transporting 1. Combine transport specifications 2. Transport locks, covers, lids 3. Frame loop locations Questions and Answers

2 ORIENTATION WALK-AROUND I. 4/2 RC Header A. Roto-shoes B. Sliced gathering belts C. Floating row units D. Hinged access panels E. Gearbelt drives time conveyors to gathering belts F. Spring loaded conveyor belts G. Throat mirror II. III. Chassis A. Covers and access panels 1. Side covers (front and rear) 2. Chamber access panels (front and rear) 3. Rear center access panel 4. Engine platform ladder, access panels, and radiator screen B. 127hp. 6 cyl. Water-cooled turbo diesel engine 1. Engine oil dipstick and fill location 2. Fuel filter and water separator locations 3. Radiator fill location C. 55 gallon hydraulic system 1. Hydraulic reservoir fill and sight glass location 2. Charge pressures and return filter locations 3. 4 wheel drive, 4 range hydrostatic drive 4. Independent threshing cylinder and header drive circuits 5. Pressure-compensated pump for aux. hydraulic functions D. V-belt and Gearbelt mechanical drives between chambers Threshing A. Threshing Cylinder (electrically adjustable) 1. Larger diameter for lower cylinder speed 2. Reverser for clean out feature 3. Hydraulic gearbelt drive B. Concave (electrically adjustable) C. Strawpullers 1. Gearbelt drive 2. Timed with threshing cylinder WALK-AROUND 2

3 ORIENTATION IV. Cleaning A. Straw walkers (2 per chamber) 1. Gearbelt drive 2. More efficiently handles threshed plant material, decreasing clean out time B. Sieves (1per chamber 19 x square inches) 1. Air assist front section 2. Large eccentric bearing drive C. Winnowing Air 1. High volume dual flow fans (2 per chamber) 2. 9-Position air dampers V. Air Delivery A. High Volume Cotton Picker style cyclone blower B. Dual 5 delivery tubes with quick clean out feature C. Y valves for bulk harvesting VI. Sample Handling A. Sample initially held in cyclone by cyclone valve B. ¼ bushel weigh hoppers with moisture probe C. Discard valves direct samples to packager or discard auger D. Discard auger transfers material to fountain auger in grain tank E. Automated Seed Packager (ASP) F. Bag conveyor G. Bucket elevator VII. Sample Storage A. Grain tank (58 bushels) hydraulic unload auger with 7 reach and 12 discharge height 2. Automatic 8 hydraulic cross auger 3. Tank cover disable switch to shut off unload, cross, and discard augers B. Bag tank (43 bushels) 1. Collapsing chute for unload auger clearance 2. Safety interlock with unload auger and bucket elevator WALK-AROUND 3

4 ORIENTATION CAB & CONTROLS I. CAB FEATURES A. Full view windshield with tinted glass B. Automotive style dome/map lights C. Top hatch for cyclone access and emergency exit D. Large mirrors for improved visibility E. Electrical panel with interior lighting F. Fold-up 2 nd seat II. SEAT ADJUSTMENTS SEAT (ONLY) SLIDE BACK REST TILT SEAT PLATE TILT SEAT AND ARM SLIDE ARMREST HEIGHT HEIGHT ADJUSTMENT WEIGHT ADJUSTMENT A. Mechanical suspension (4 stroke) with shock absorber 1. Height adjustment three 2-½ increments by lifting seat 2. Weight adjustment 110 to 285 lb. by turning the bottom knob B. Seat cushion and backrest 1. Seat plate tilt 8 to 12 by turning upper knob on front of seat 2. Backrest tilt 12.5 forward to 15 backward in 2.5 increments by lifting lever on back of seat (left side) 3. Seat (only) slide (relative to control carriers) 6 in ½ increments by lifting lever on right front of seat cushion C. Control carriers 1. Arm pivot pull up on front of carrier (right side will disable ground drive controller) 2. Seat and arm slide (carriers and seat) 6 in ½ increments by lifting on full-length bar in front of seat 3. Armrest height 6 variable by knob on outside of carrier CAB & CONTROLS 4

5 ORIENTATION III. SEAT MOUNTED CONTROLS (5) ASP STATUS LIGHT (4) ASP PROGRAM CYCLE (3) LOWER HEADER (2) RAISE (6) INCREASE (ON) THRESHING CYLINDER SPEED (7) DECREASE (OFF) (15) BAG TANK DUMP (14) UNLOAD AUGER RUN (13) UNLOAD AUGER FOLD (1) FORWARD / REVERSE CONTROL LEVER (12) BLANK IDLE HARVEST (8) ENGINE SPEED (11) GRAIN TANK AUGER (10) BLANK (9) GROUND SPEED RANGE Figure C-4 Seat Mounted Controls A. Right side front pad 1. Forward Reverse control lever a. neutral detent and friction control 2. F-R control handle a. head up switch b. head down switch c. ASP status light d. ASP cycle switch e. threshing cylinder speed increase switch f. threshing cylinder speed decrease switch B. Right side rear pad 1. Ignition switch 2. ENGINE SPEED switch a. IDLE position for start up and clutch engagement b. (middle range) position for some driving and aux. functions c. HARVEST position for harvesting, road gear, etc. d. GROUND SPEED switch a. position 1 lowest range for loading and unloading (0 to 7.5 mph) b. position 2 low range for harvesting (0 to 12 mph) c. position 3 high range for harvesting (0 to 14 mph) CAB & CONTROLS 5

6 ORIENTATION d. position 4 highest range for road driving (0 to 20 mph) 3. HEAD SPEED switch a. variable scale from 0 to 25 C. Left side front pad 1. BRAKE switch a. controls electric fail-safe parking brake (part of seat safety and neutral safety circuits) 2. CLUTCH switch The following are engaged and disengaged by the clutch switch: a. cyclone blower b. winnowing blower c. front and rear internal conveyors d. straw walkers e. shaker pans (sieves) D. Left side rear pad (unloading functions) 1. BAG TANK DUMP switch a. out to unload, in to load b. unload auger must be folded out and bucket elevator must be home 2. UNLOAD AUGER switch a. auger must be folded out b. head speed valve must be off c. grain tank lid must be closed 3. FOLD AUGER switch a. out to unload grain tank or bag tank b. in for harvesting and transport IV. STEERING COLUMN ADJUSTMENTS AND CONTROLS A. Column tilt (at floor) 5 forward to 15 back by pushing or pulling column (friction positioning) B. Steering wheel tilt 20 forward to 20 back in 10 increments by pulling tilt lever down toward operator C. Controls STEERING COLUMN TURN SIGNAL SWITCH HAZARD SWITCH CAB & CONTROLS 6

7 0 0 F C F C SHP 90 ORIENTATION 1. Turn signal lights lever a. right turn push lever up (cw), right indicator will flash b. left turn pull lever down (ccw), left indicator will flash 2. Hazard lights switch a. push switch indicator will light b. turn signals will over-ride hazard lights D. Shaft Monitor (only on this machine for testing) See monitor manual V. Gauge Panel THRESHING CYLINDER RPM 10 ENGINE RPM MAIN POWER AUXILIARY POWER FUEL 1/2 ENGINE HOURS THRESHING HOURS RPM x HOURS HOURS VOLTS + - VOLTS + - FUEL RPM ENGINE TEMP. SHUTDOWN ENGINE WATER TEMP. ENGINE OIL PRESSURE HYDRAULIC OIL TEMP. GROUND DR. CHARGE PRESSURE T/C DRIVE CHARGE PRESSURE psi low 100 bar psi bar psi bar TRANS TRANS WATER OIL TRANS OIL OIL CHECK AIR FILTER OPS SHUTDOWN TEMP PRESS TEMP PRESS PRESS 1. Threshing Cylinder Tachometer Displays speed in rpm (depends on crop and harvesting conditions) 2. Engine Tachometer Approx. engine speeds: Idle 900 rpm, Midrange 1800 rpm, Harvest 2500 rpm 3. Main Power Voltmeter Voltage supplied by main power alternator Normal operating range: 13.5 to 14.5 Volts at full engine rpm Should stay in the green range 4. Auxiliary Power Voltmeter Voltage supplied by auxiliary power alternator Normal operating range: 13.5 to 14.5 Volts at full engine rpm Should stay in the green range 5. Fuel Gauge Displays diesel fuel level in 66 gallon tank 6. Engine Hour Meter Displays hours of machine operation for maintenance procedures 7. Threshing Hour Meter Displays hours with clutch engaged for maintenance procedures 8. Check Air Filter Light Illuminates when air filter restriction reaches 20 H 2 O (5 kpa) Filter should be checked and cleaned or replaced as needed 9. Operator Presence Shutdown Light CAB & CONTROLS 7

8 ORIENTATION Illuminates when Operator Presence System has shut the engine off To restart the engine, the following conditions must be met: -Ground drive control must be in "NUETRAL" -Brake "ON" -Clutch "OFF" -Header "OFF" -Threshing cylinder "OFF" -Discard auger "OFF" -Unload auger "OFF" 10. Engine Temperature Shutdown Light Illuminates when engine has shut down because of overheating 11. Engine Water Temperature Gauge Displays engine coolant temperature Normal operating range: 170 to 225 F 12. Engine Oil Pressure Gauge with low pressure indicator light Displays engine oil pressure and indicates low pressure Normal operating range: 50 to 100 psi Indicator lights before engine starts and if pressure drops to 15 psi 13. Hydraulic Oil Temperature Gauge Displays Hydraulic Oil Temperature in reservoir Normal operating range: 100 to 150 F 14. Ground Drive Charge Pressure Gauge Normal operating range: 300 to 400 psi 15. Threshing Cylinder Drive Charge Pressure Gauge Normal operating range: 250 to 300 psi VI. Switch Panel SWITCH BANK #1 ASP SWITCH BANK SWITCH BANK #2 SWITCH BANK #3 WB RADIO (OPTIONAL) A. Switch Bank #1 1. Cyclone (manual override) Opens knife valve in cyclone and Y-valve until switch is released, then closes Up opens left row Down opens right row CAB & CONTROLS 8

9 ORIENTATION 2. Weigh Hopper (manual override) Opens valve in weigh hopper until switch is released, then closes Up opens left row Down opens right row 3. Elevator (manual override) Operates elevator that moves samples from conveyor to bag tank Up moves up until switch is released, then stops Down moves down until switch is released, then stops 4. Bucket Dump / Conveyor (manual overrides) Up tilts the bucket until switch is released, then tilts back Down runs the conveyor for 6 seconds or until switch is released, then stops 5. Threshing Cylinder Reverse Ramps T/C speed in reverse until switch is released, then ramps back (threshing cylinder must be stopped before reverser will engage) 6. Concave Clearance Up increases clearance Down decreases clearance B. Switch Bank #2 1. DC Electronics Powers DC Voltage electronics 2. ASP DC Power Powers DC components of Automated Seed Packager V AC Powers AC inverter for ASP and outlets 4. Discard Auger Operates auger to move discarded samples to grain tank 5. Bulk Harvest / Sample Harvest Positions air delivery Y-valves Bulk harvest sends both rows directly to grain tank Sample harvest sends both rows to cyclones 6. Grain Tank Auger Override Manually operates grain tank cross auger that feeds unload auger C. Switch Bank #3 1. Field Lights / Road Lights Field lights are all exterior harvest, unload, and rear lights Road lights are 2 headlights only (others off for highway driving) 2. ASP Service Lights / ASP Bag Lights ASP Service lights illuminate the entire packager area ASP Bag lights illuminate the bag filling area only 3. Mirror (optional) Up rotates right side mirror out for harvest and driving Down rotates mirror in for transport D. ASP Switch Bank 1. Left Row Operates left row of dual packager 2. Right Row Operates right row of dual packager 3. Left Row Bag Advance CAB & CONTROLS 9

10 ORIENTATION Feeds bags on left side of dual packager 4. Right Row Bag Advance Feeds bags on right side of dual packager 5. Start Cycle Starts the ASP cycle of bag fill, seal, drop, and ready next bag E. AM - FM - Stereo - WB Radio (optional) 1. On-Off / Volume Control Turn clockwise to turn on. Continued rotation increases volume If unit is off but ignition on, clock will display 2. Bass Control (pull knob) Pull knob out to bass position Turn left to increase and right to decrease bass response Press knob back in 3. Treble Control Turn knob left to increase and right to decrease treble response 4. Left-Right Speaker Balance Control Turn knob left or right to obtain desired speaker balance 5. Front-Rear Speaker Fader Control Not functional with 2 speaker system 6. AM-FM-WB Band Selector Press button to change radio band (FM1, FM2, AM, WB) If FM Stereo signal is received, STEREO will appear in display 7. Up-Down Tuning & Seek Tap DOWN or UP to change frequency by 1 digit Press and hold DOWN or UP to SEEK the next broadcasting station 8. Station Pre-set Memory To set the five pre-sets for the four broadcast bands: Turn on radio and select desired band Press and hold desired preset button until sound mutes and returns The corresponding CH number will display Note: memory pre-sets will be erased if battery is disconnected 9. Liquid Crystal Display (LCD) Graphically displays radio band, tuning frequency, or time 10. Time / Frequency Select (CALL) CAB & CONTROLS 10

11 ORIENTATION Sets the primary display (time or frequency) during operation SETTING THE CLOCK Turn ignition on and radio off Press and hold CALL button until time flashes Press UP to change minutes and DOWN to change hours Note: time setting will be lost if battery is disconnected VII. Environmental Controls HEAT control A/C control A/C switch FAN speed switch INCREASE TEMP OFF A. Heater (standard) 1. Heater valve on engine block must be open 2. Adjust HEAT control 3. Adjust FAN speed switch B. Air Conditioning (optional) 1. Heater valve on engine block must be closed 2. Turn on AIR CONDITIONING switch 3. Adjust AIR CONDITIONING control 4. Adjust FAN speed switch 5. Open Recirculation slide gate for maximum cooling CAB & CONTROLS 11

12 ORIENTATION OPERATION & PROCEDURES VII. VIII. DAILY INSPECTION Check engine oil level Check hydraulic fluid level Check radiator coolant level Check radiator screen STARTING THE ENGINE A. The following controls and switches must be set accordingly to start the engine: -Ground drive control must be in "NUETRAL" -Brake "ON" -Clutch "OFF" -Header "OFF" -Threshing cylinder "OFF" -Discard auger "OFF" -Unload auger "OFF" B. Set throttle to "IDLE" C. Turn key clockwise one click, wait for glow plug indicator to go out (depends on the engine temperature) D. Start the engine IX. GETTING READY TO HARVEST A. Determine initial settings of: 1. Header cutting height (set by position of roto-shoes) 2. Header float (position so header tin matches throat stripe) 3. Header gathering belt speed (depends on harvest ground speed) 4. Concave Clearance (depends on condition of soybeans) 3-1/2 on indicator is about 3/8 5. Threshing Cylinder Speed (depends on condition of soybeans) 300 to 400 RPM 6. Winnowing Air Dampers (depends on condition of soybeans) Position 4 (1 = minimum amount of air, 9 = maximum) B. Turn clutch "ON" with the engine at idle C. Select "BULK HARVEST" or "SAMPLE HARVEST" on diverter valve If "SAMPLE HARVEST" turn on the following functions in the order listed: -Turn DC ELECT. "ON" -Turn ASP DC POWER "ON" -Turn 110V AC "ON" D. For packaging, turn LEFT ROW & RIGHT ROW "ON" E. For discarding, turn DISCARD AUGER "ON" F. Set engine speed to "HARVEST" G. Set threshing cylinder speed H. Turn header on and set speed "0-25" to match ground speed OPERATION & PROCEDURES 12

13 ORIENTATION I. Adjust concave clearance J. Adjust winnowing air dampers on the sides of the machine as needed X. CLEAN OUT FEATURES A. Threshing Cylinder Reverser If threshing cylinder becomes plugged: 1. Change threshing cylinder speed control back to zero 2. Press and hold the Threshing Cylinder Reverser switch. The cylinder will start turning backwards and will increase in speed until switch is released. 3. Release Threshing Cylinder Reverser switch (The cylinder will automatically slow down to a stop) 4. Set threshing cylinder to previous speed B. Venturi Access Doors If the venturi areas become plugged: 1. Disengage clutch 2. Lift up the trash deflector 3. Release the holding pins 4. Clean out the area 5. Return access door to operating position C. Air Delivery System If the air delivery system (cross tubes) become plugged: 1. Disengage clutch (to stop cyclone blower) 2. Release quick-clamps and remove elbows on right side of machine 3. Remove front cross tube (if necessary) by removing pins and sliding tube out 4. Manually clean out blockage and save sample (if desired) CAUTION Do not use blower to clean out blockage. 5. Reinstall cross tube, elbows, and quick-clamps D. Unload Auger Door If it is necessary to clean out the grain tank: 1. Shut off machine 2. Release camloc latch and open clean out door 3. Open grain tank cover and blow out with compressed air (if desired) DANGER Do not enter grain tank with combine running. 4. Close clean out door before operating machine XI. UNLOADING GRAIN A. Grain Tank Unloading 1. Fold unload auger out 2. Secure manual clamp on auger 3. Shut off head (unload auger will not run with head on) 4. Engage unload auger (cross auger will run automatically as needed) 5. Disengage unload auger, Release clamp, Fold auger in B. Bag Tank Unloading 1. Fold unload auger out (bag tank will not move unless auger is out) 2. Bucket elevator must be in home position 3. Dump bag tank (out) 4. Retract bag tank (in) (Bucket elevator will not function with bag tank out) OPERATION & PROCEDURES 13

14 ORIENTATION 5. Fold unload auger in XII. TRANSPORTING MACHINE A. Combine Transport Specifications: 1. Weight: 22,500 lb. 2. Height: Width: Length: 26 5 with head 5. Wheel base: Ground clearance: Max. trailer ramp angle: 25 B. Before transporting machine: 1. Securely latch side covers 2. Securely latch and pin engine access panels 3. Rotate spring latches to secure engine access doors, rear ladder, and center access cover 4. Pin right side ladder platform and lock packager access door 5. Pivot right side power mirror in 6. Install solid cyclone covers C. Only use frame loops to chain combine to trailer. 1. Front frame loops front side of front axle 2. Rear frame loops above rear axle between trash deflectors IMPORTANT Do not wrap chain around rear axle, machine damage will result. HELP: ALMACO ( Normal Office Hours 7:30 AM to 5:30 PM ) Phone Main: (515) Phone Auto-Answer with Extension: (515) Fax: (515) Service Address: service@almaco.com Online Manuals: ALSO SEE TROUBLESHOOTING GUIDE IN MANUAL OPERATION & PROCEDURES 14

15 SECTION D TROUBLESHOOTING TROUBLESHOOTING D-1

16 D-2 TROUBLESHOOTING

17 TROUBLESHOOTING PROBLEM PROBABLE CAUSES ADJUSTMENT MACHINE HARVESTING PROBLEMS Threshing cylinder plugging Crop too green Harvest rate too high Concave clearance too tight Cylinder speed too slow Plant material hangs up on sieves or straw walkers Venturi tubes plugged Plant material in samples Drive belt loose or broken Other component failure Crop too green Material caught in sieve or walkers holding other material Plant material catching on curtains Cyclone lid is plugged Harvest rate too high Blower belt loose or broken Incorrect winnowing blower shutter setting Wait for crop to mature Reduce ground speed Increase concave clearance Increase threshing cylinder speed Tighten or replace belt Contact ALMACO Wait for crop to mature Clean off sieves Remove curtains Clean cyclone lid screen Replace transport lids Remove venturi elbow, clean venturi, reduce ground speed Repair or replace Increase shutter setting (more air) Threshing cylinder grinding up plant material Decrease threshing cylinder speed Increase concave clearance Unthreshed grain in the Incorrect threshing cylinder Increase threshing cylinder discharge (out rear of the speed speed machine) Incorrect concave clearance Decrease concave clearance Threshed grain in the Threshing cylinder throws grain Install or lengthen curtains discharge (out rear of out rear of machine machine) Incorrect winnowing blower setting MACHINE MECHANICAL PROBLEMS THRESHING CYLINDER / STRAWPULLER Threshing cylinder will not turn Threshing area plugged with material Drive belt loose or broken Pump cable broken or seized Fuse blown Actuator failure Bearing failure (worn, seized) Pump failure Motor failure Decrease shutter setting (less air) Use cylinder reverser OR turn off machine and remove slug manually Tighten or replace belt Replace control cable Replace fuse Replace actuator Replace bearings Repair or replace Repair or replace TROUBLESHOOTING D-3

18 Cannot adjust threshing cylinder speed SHAKER PAN DRIVES Shaker pans are not moving SHAKER PANS / SIEVES Shaker pans hitting sides of combine INTERNAL CONVEYORS Conveyor does not turn WINNOWING BLOWER Blower does not turn Blower makes unusual noise (vibrating) CYCLONE BLOWER Blower does not turn Fuse blown Control cable broken Cable sticky or binding Actuator failure Clutch not engaged Loose or broken drive belt Loose or broken drive sprocket Eccentric bearing failure Gearbox failure Shaker drive arm out of adjustment Cracked or missing rubber bushing(s) Clutch not engaged Conveyor belt is loose Lacing or pin broken Loose or broken drive belt Bearing failure Gearbox failure Clutch not engaged Loose or broken drive belt Blower fins plugged Bearing failure Broken blower fan Blower wheel loose and rubbing Clutch not engaged Loose or broken drive belt Bearing failure Upper jack shaft coupling failure Blower makes unusual noise Blower fins plugged Shaft nuts loose Bearing failure Broken fan blade D-4 TROUBLESHOOTING Replace fuse Replace control cable Replace control cable Replace actuator Turn clutch switch on at idle Check clutch fuse Tighten or replace belt Tighten set screws, replace key or sprocket Replace bearing Repair or replace Adjust shaker arms Replace rubber bushings Turn clutch switch on at idle Tighten belt (See conveyor adjustment) Fix or replace lacing, pin, or belt Tighten or replace belt Replace bearings Repair or replace Turn clutch switch on Check clutch fuse Tighten or replace belt Clean fins Replace bearing Replace blower fan Tighten clamps Turn clutch switch on at idle Check clutch fuse Tighten or replace belt Replace bearings Replace or repair coupling Clean fins Tighten nuts on both sides Replace bearing Replace blower fan

19 ENGINE Engine does not turn over Engine turns over but fails to start Engine starts, but runs rough or kills often Engine shut down, engine status light flashing 4 times. Engine shut down, engine status light not flashing. GROUND DRIVE Combine will not move with engine started Ground drive not in neutral Clutch, transfer auger, or unload auger switch is on Head speed control or threshing cylinder speed control not off Brake switch is off Dead battery Poor battery cable connections Faulty ignition switch Faulty starter Faulty neutral safety switch Bad starter relay Not getting fuel Air in fuel line Water in fuel Dirty fuel filter Plugged air cleaner Engine coolant temperature is too high. Engine oil pressure low. Operator Presence System shut engine down Out of Fuel Plugged fuel filter Other mechanical problems Parking brake switch engaged Torque hub(s) disengaged Parking brake is not releasing Component failure Position lever in neutral Move these switches to the off position Turn Head and threshing cylinder off Turn brake switch to on Charge battery or replace Clean battery posts and tighten cable connections Replace ignition switch Replace starter Replace switch Replace relay Fuel tank empty Fuel filter plugged Check fuel pump drive belt Check engine controller solenoid Check / replace fuel pump Check fuel lines / fittings, bleed air from return lines Drain water separator and Change fuel filter Replace fuel filter Clean air filter and pre-cleaner Coolant level too low. Fill to bottom of reservoir tube. Clean radiator, oil cooler, and condenser with compressed air or high pressure washer Check engine oil level and check for leaks Check gauge, call ALMACO Refer to engine starting procedure to restart engine Add Diesel, bleed air from system, and restart engine Replace filter Contact ALMACO Disengage parking brake switch Flip torque hub caps Check auxiliary pump pressure Contact ALMACO TROUBLESHOOTING D-5

20 ROW CROP HEAD HARVESTING PROBLEMS Plants pulled out of ground by Incorrect ground speed Increase ground speed belts before being cut Incorrect header speed Decrease header speed Plants pushed out of the Incorrect ground speed Decrease ground speed ground before being cut Incorrect header speed Increase header speed Unharvested grain remains Incorrect header height Lower header on plant in field Cutting height set too high Lower cutting height by raising shoes Snout not lifting fallen plants Lower snout Header conveyor belts stopping Conveyor belt too loose Tighten spring tightener just enough to run Material between concave lip and conveyor Stop machine and clear manually Header drive belt or conveyor drive belt loose or broken Tighten or replace drive belt Dirt in seed samples Header too low Raise header Raise cutting height by lowering Roto-Shoes or skids Gathering belt too fast Decrease header speed Gathering belt / knife jams Crop too green Allow crop to mature before harvesting ROW CROP HEAD MECHANICAL PROBLEMS Gathering belt / knife jams Incorrect knife clearance Adjust per JD Row Crop Manual Gathering belts / rotating Header speed control turned Turn on Header speed control knives will not turn off Jammed by rock, stalks, etc. Turn off machine, remove plug manually Rotary knife drive too tight Loosen spring tightener Hoses unattached to quick Reattach hoses coupler Valves of quick coupler closed Pull valve levers forward Gathering belt too tight Loosen gathering belts Header conveyor / pinch belts Header speed control turned Turn Header Speed control on will not turn off Conveyor belt too loose Tighten spring tightener just enough to run Material between concave lip and conveyor Tighten belt (see conveyor adjustment) Lacing or pin broken Fix or replace lacing, pin, or belt Header drive belt or conveyor drive belt loose or broken Tighten or replace belt If the problem does not appear in this section or if there are any questions on how to proceed with a solution contact ALMACO. D-6 TROUBLESHOOTING

21 SECTION E MAINTENANCE MAINTENANCE E-1

22 SPC 90 E-2 MAINTENANCE

23 GUIDELINES (See SECTION F COMPONENT SERVICE INFORMATION in the PARTS MANUAL for more information) Your new combine is intended to give you many years of problem-free harvesting. Preventive maintenance and regular service is the best way to avoid problems before they occur. Only properly trained personnel should service or repair the machine. Follow the guidelines before beginning any work on the combine: WARNING! Do not unload or service machine under high voltage lines. Contact with power lines can cause serious injury or death. WARNING! To prevent injury, never lubricate or service combine, header, or engine while it is running. Stop the machine, set parking brake, turn engine off, and remove key. WARNING! Shock hazards can cause serious injury or death. Only qualified personnel should service electrical systems. - Shut off the engine and disconnect the battery before opening electrical access panels to change fuses, relays, switches, etc. - Disconnect all electronic equipment (Seed Spector, printer, hand-held computer, Automated Seed Packager, etc.) before jump starting or welding on machine. WARNING! High pressure fluids can cause serious injury. Release pressure before disconnecting hydraulic lines or servicing system. WARNING! Chock wheels before working on ground drive hydraulic circuit. Torque hubs could free wheel causing serious injury or death. - Relieve hydraulic pressure before removing or replacing hydraulic lines. Contact ALMACO, if serious hydraulic system work is needed. NOTICE: Lubricate all relubricatable bearings, pivots, U-joints, and slip sleeves with lithium based E.P. grease meeting or exceeding N.L.G.I. grade 2 specifications. Do not over grease bearings, excessive grease will damage bearing seals causing early failure. Clean grease gun tip and zerk before lubricating. MAINTENANCE E-3

24 SPC 90 MAINTENANCE SCHEDULE Interval (in hours of operation) SERVICE POINT COMBINE Check chains for proper tension, sprocket wear, and lube. X Check all belt drives for wear and proper tension. X Check for oil, hydraulic fluid, and coolant leaks. X Grease header pivots, U-joints, slip sleeves, and upper X jackshaft bearings (one pump only). Invert and shake fire extinguisher to eliminate compaction. X Check cables and linkages for proper operation. A Check rubber shaker bushings condition and alignment. A Inspect blower impellers, Clean impellers and housings. X FRONT AND REAR AXLE Lubricate rear axle pivot, spindles, tie rods. X Check front and rear tire pressure (See tire side walls). A Retorque all wheel bolts and lug nuts. I A Change torque hub oil (90 wt.). ENGINE Clean radiator, oil cooler, A/C condenser, and fuel cooler. X Inspect, replace, clean cab air intake filter A Change engine oil and oil filter. I A Clean battery cables, posts, and cable ends. A Replace fuel filter (spin-on type). I A Check fuel prefilter (canister type). Drain water and replace I A element as needed. Drain, flush, and change engine coolant. HYDRAULIC SYSTEM Change hydraulic oil filters (charge pressure and return). A Change hydraulic oil. HEADER ROW CROP HEAD Check for wear on all sprockets, gears, idlers, and guides. X Check conveyor belts tension, tracking, and lacing. Check gearbelts for tension, alignment, and cracking. Check gathering and knife chains for tension, alignment, and wear. Grease U-joints and slip sleeves. Key: X = Requiredservice interval I = Initially,athour interval thereafter A = Annuallyor athour interval whichever comesfirst B = Biennially(everytwoyears) or athour interval X X X X X B X E-4 MAINTENANCE

25 DAILY MAINTENACE CHECKLIST Before starting and operating the combine complete this Daily Maintenance Checklist. 1. Check safety equipment. 2. Check engine oil level, check for leaks. 3. Check hydraulic oil level, check for leaks. 4. Check engine coolant level, check for leaks. 5. Check engine and cab air filters. Frequency of cleaning varies with conditions. 6. Grease straw walker bearing blocks. (1/2 pump only) 7. Remove plant material from head, sieves, and intake screen. 8. Check charge pressure gauges at full engine rpm. SERVICE RECORD DATE SERVICE PERFORMED MAINTENANCE E-5

26 SPC 90 SERVICE POINTS CAB AIR INTAKE FILTER #41250 FUEL FILL DIESEL ONLY FUEL PRE- CLEANER WATER SEPARATOR HYDRAULIC OIL RETURN FILTER #10278 AIR PRE-CLEANER AND FILTER MAIN FILTER #14196 SAFETY FILTER #14197 CHARGE FILTERS #10387 OIL FILL 15W40 OIL FILTER #39179 FUEL FILTER #40643 HYDRAULIC OIL FILL AND CHECK DEXRON III RADIATOR FILL AND LEVEL CHECK Figure E-1 Service Points E-6 MAINTENANCE

27 ELECTRICAL SYSTEM WARNING! Shut off engine and disconnect the battery before servicing electrical system. Electric shock will cause serious injury or death. This machine may have a 110 volt electrical system. The 110 volt system should only be serviced by qualified personnel. FUSES: See inside of electrical compartment for fuse size and location. If required to change a fuse, replace with fuse of same amperage rating and of the same style. CIRCUIT BREAKERS: A 6 amp auto-reset breaker (#17264) located in the electrical panel protects the concave clearance motor. A 20 Amp manual reset breaker (#18650) is located in the electrical panel and powers the engine starter solenoid and excess fuel start solenoid. An 80 Amp auto-reset breaker (#19237) supplies power to the glow plugs (when equipped). The glow plug breaker is located on the engine with the engine speed controller. RELAYS: These relays control some combine functions and are located in the electrical panel. To replace a single pole relay (#18284), push the spring clip (#18160) to the side, then pull the relay straight out of the socket (#18591). The double pole relay (#18479) is removed the same way. The double pole relay require a different spring clip (#18481) and socket (#18480). CUBE RELAYS: These relays are also used for combine functions and are located in the electrical panel. To replace a cube relay (#18916), pull the relay cube straight up to remove. Do not remove the white plastic retainer from the front of the socket (#18915). LIGHT SERVICE: If several lights go out at once, check the appropriate fuse(s). If only one light is out, it may be the bulb or a loose connection. The lights, bulbs, and part numbers used on the combine are in the following list or in the parts manual: 1. Headlights The headlights are a sealed beam halogen light that draws 4 amps. The lights can only be replaced as an assembly (#18570). 2. Running Lights The rear lights, tank lights, unload auger light, etc. are all sealed beam off-road lights. These lights draw 2.5 amps each. The light can only be replaced as an assembly (#18041). 3. Turn Signal / Hazard Lights These lights are located on the front and rear corners of the combine. Each light has one 3157 bulb and a reflective amber lens. The light can be ordered as an assembly (#28220). MAINTENANCE E-7

28 SPC Rear Marker Lights These red marker lights are located on the rear of the combine. Each light has one 3157 bulb and a reflective red lens. The light can be ordered as an assembly (#18216). 5. Switch / Gauge Lights The lights used in the switches and gages are unique to the manufacturer and replacements may be hard to find. The light for the SWF rocker switches can be purchased as an assembly (#18874) or replacement bulb (#18888). The replacement bulb for the Datcon gauge light is part number (#16049). For questionsconcerningspecificoptions,or for asistance on servicingyour equipment call ALMACO for asistance. E-8 MAINTENANCE

29 HYDRAULIC SYSTEM The ALMACO SHP 90 Combine utilizes hydraulic systems to provide power to the components used for threshing, ground drive, steering, header lift, and various options. Power is supplied directly by the engine, which drives two variable displacement pumps, a fixed displacement gear pump, and a pressure compensated piston pump. The first pump (closest to the engine) supplies power to the ground drive and is controlled by the ground drive controller actuator. The second pump (middle) supplies power to the threshing cylinder motor and is controlled by an actuator and cable system. The third pump powers the load sensing power steering, the head motor or the unload auger motor run through a stack valve. The piston pump is driven from the upper jackshaft and pressurizes the large valve stack. The header lift, transfer auger motor, transverse auger motor, auger fold, and other auxiliary functions are powered by this pump. HYDRAULIC RELIEF VALVES NOTE: All hydraulic relief valves are pre-set at the factory. Contact ALMACO before making any adjustments. RECOMMENDED HYDRAULIC RELIEF OIL PRESSURE SETTINGS: a. Ground drive: 5000 psi port A 5000 psi port B b. Threshing cylinder: 3500 psi c. Gear pump: 3000 psi d. Auxiliary pump: 2000 psi RETURN FILTER VALVE: Shuts off the hydraulic lines so the reservoir does not drain while changing the return filter. The valve must be opened before engine will start. Check return filter valve light, if illuminated valve is closed and combine will not start. Open for Operation Close to change filter Figure E-2 Return Filter Valve Positions MAINTENANCE E-9

30 SPC 90 ENGINE STARTING PROCEDURE WARNING! Do not start engine in enclosed unventilated area. Fumes could cause operator illness or death. WARNING! Make sure all people are in a safe position before starting. Sound horn and call CLEAR to warn others. BEFORE STARTING THE ENGINE 1. Put ground drive control lever in neutral. 2. Turn parking brake switch on. 3. Turn clutch switch off. 4. Turn head speed control off. 5. Turn threshing cylinder off. 6. Turn discard auger switch off. 7. Turn unload auger switch off. 8. Return filter valve open. Set the engine speed control to idle position. Insert key, rotate key clockwise one click for acc power. Threshing cylinder indicator will illuminate (green). Rotate key clockwise one more click to power on. OPS Status Light (blue) should be illuminated. If not recheck above conditions. Wait To Start light will illuminate in cold weather. Glow plugs will be activated dependant on engine temperature, so time will vary accordingly. When Wait To Start light goes out, turn key clockwise to the start position and hold until engine starts. Do not crank starter for more than 20 seconds. If engine fails to start, turn off key and wait one minute, then retry. If engine does not start on second attempt, See SECTION D TROUBLESHOOTING or the Deutz Operation Manual. E-10 MAINTENANCE

31 CONVEYOR BELT ADJUSTMENT All conveyor belts should run straight and evenly across roller surfaces without binding or scuffing the side frame. The belt tension should only be tight enough to prevent slipping. Before adjusting, determine the cause of the problem. New belts may stretch during the break-in period and may require a tension adjustment. NOTE: Over tightening the belt can cause laces to pull apart or rollers to break. The combine is equipped with spring loaded conveyor belt take-ups. The spring adjusters can handle the changes in belt length as the lacing travels around the rollers and as the belt stretches. There are two types of spring loaded adjusters. See Figure E-3 Pusher Conveyor Adjuster and Figure E-4 Puller Conveyor Adjuster for proper adjustment procedures. When installing replacement belts, clean the roller surfaces and V-guides. Build up on the roller surfaces can cause stretching, excessive wear, and misalignment. Position the V-guide on the inside of the belt so that it rides in the center of the V-groove in the roller. TENSION BOLT 1/8 CLEARANCE STOP NUT BOLT JAM NUT ADJUSTER JAM NUT Figure E-3 Pusher Conveyor Adjuster To Loosen Adjuster: 1. Locate the adjustment assembly on both sides of roller. 2. Loosen the bolt jam nuts and tension bolts to remove spring pressure. 3. Loosen adjuster jam nuts and stop nuts. Push the roller in to loosen the conveyor belt. To Tighten Adjuster: 1. Pull roller out to remove all slack from belt. Make sure belt V-guide is in the roller V-groove. 2. Tighten the stop nuts until there is an 1/8 clearance from stop nut washer to adjuster housing. 3. Tighten the tension bolts evenly until the belt stops slipping. If the belt does not track evenly, and rubs on the inside of the machine tighten the tension bolt on side the belt is rubbing. 4. Tighten all jam nuts securely. MAINTENANCE E-11

32 SPC 90 JAM NUT TENSION NUT Figure E-4 Puller Conveyor Adjuster To Loosen Adjuster: 1. Locate the adjustment assembly on both sides of roller. 2. Loosen the jam nuts and tension nuts to remove spring pressure. 3. Push the roller in to loosen the conveyor belt. To Tighten Adjuster: 1. Pull roller out to remove all slack from belt. Make sure belt V-guide is in the roller V-groove. 2. Tighten the tension bolts evenly until the belt stops slipping. If the belt does not track evenly, and rubs on the inside of the machine tighten the tension bolt on side the belt is rubbing. 3. Tighten jam nuts securely. E-12 MAINTENANCE

33 HIGH PRESSURE WASHING (Water and Mild Solvent) High pressure cleaning with water and mild solvent is advisable provided the following points are observed. 1. Lightly wash entire machine with solution to float abrasive particles off the machine, which might otherwise be blown into bearings and other critical surfaces as the cleaning procedure continues. A recommended safe distance is at least 2 to 3 feet between nozzle and machine. 2. Avoid close contact of nozzle to machine (less than 12" to 15"), as high pressure jet stream at this distance imparts a cutting action which will lift and remove paint. In addition, close nozzle contact may also damage seals, inject water into, or blow grease from bearings and other lubricated surfaces, leaving exposed parts susceptible to rust and wear. NOTE: Lubricate all bearings and other lubricated surfaces, after washing and run machine for a short period to aid in moisture removal. Paint bare metal surfaces as needed to prevent rust 3. Engine may be washed totally, but avoid trapping moisture in electrical components, and do not wash a "hot" engine with cold water, as the differential in temperature could cause cracking of exhaust manifold and other components. 4. Mild solvents of a non-flammable nature may be suitable for cleaning, provided manufacturer's specs are compatible with alkyd enamels, rubber and plastics as used on the combine. 5. Using steam as a cleaning agent is not recommended by ALMACO, as steam is viewed as a potentially destructive agent to plastics, paint and rubber and promotes rust and corrosion of components, which are not immediately protected after cleaning. MAINTENANCE E-13

34 SPC 90 E-14 MAINTENANCE

John Deere. MODEL: 4400 Combine JD-O-OMH86804

John Deere. MODEL: 4400 Combine JD-O-OMH86804 John Deere MODEL: 4400 Combine THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY

More information

TRUCKINGTRUTH.COM T T. Daniel B s Pre-Trip Inspection Checklist

TRUCKINGTRUTH.COM T T. Daniel B s Pre-Trip Inspection Checklist TRUCKINGTRUTH.COM T T Daniel B s Pre-Trip Inspection Checklist 1 My pre-trip begins as I approach the vehicle. I am looking for leaks, leaning one way or the other (which may indicate a low tire or bad

More information

SRT OPERATIONS MANUAL

SRT OPERATIONS MANUAL MAINTENANCE SECTION PAGE # VEHICLE DAILY INSPECTION.......................................1 P.M. INSPECTION #1.................................................3 P.M. INSPECTION #2.................................................6

More information

tRIPr Chief Grain Cart. Operator s Manual. Operator s Manual

tRIPr Chief Grain Cart. Operator s Manual. Operator s Manual 125-000-01 125-000-01 1tRIPr 1tRIPr Operator s Manual 1210 Chief Grain Cart Operator s Manual Operator s Manual TO THE DEALER Predelivery/Delivery Checklist 1210 Grain Cart PREDELIVERY/DELIVERY CHECKLIST

More information

As a safety precaution, remove keys from the ignition while working under or around the vehicle.

As a safety precaution, remove keys from the ignition while working under or around the vehicle. CAB AND CHASSIS As a safety precaution, remove keys from the ignition while working under or around the vehicle. 1. Approach Check the overall appearance of vehicle stance (not leaning). Check for signs

More information

Hanna Daily Preventive Maintenance Schedule

Hanna Daily Preventive Maintenance Schedule Hanna Daily Preventive Maintenance Schedule Location Location # Daily operation and inspection procedures to be performed by car wash personnel. Mark status in the spaces on the right after performing

More information

9895 Combine Parts Catalog EFF. S/N HSC8101

9895 Combine Parts Catalog EFF. S/N HSC8101 9895 Combine Parts Catalog EFF. S/N HSC8101 1 FORWARD ALPHABETICAL INDEX The complete alphabetical index appears at the beginning of this publication. It is used to locate major groups, assemblies and

More information

DUST COLLECTOR (BOTTOM REMOVAL BAG & CAGE) INSTALLATION AND OPERATING INSTRUCTIONS

DUST COLLECTOR (BOTTOM REMOVAL BAG & CAGE) INSTALLATION AND OPERATING INSTRUCTIONS 4080 SE International Way. Suite B110, Milwaukie, OR 97222 (503) 654-0867 Fax: (503) 654-4671 email: ftech@filtertechnologyltd.com www.filtertechnologyltd.com DUST COLLECTOR (BOTTOM REMOVAL BAG & CAGE)

More information

WHEEL LOADER 938H WHEEL LOADER 938H. Power Generation - Bulk Materials Standards I. GENERAL: DESCRIPTIONS FOR CATERPILLAR MODEL 938H WHEEL LOADER:

WHEEL LOADER 938H WHEEL LOADER 938H. Power Generation - Bulk Materials Standards I. GENERAL: DESCRIPTIONS FOR CATERPILLAR MODEL 938H WHEEL LOADER: Power Generation - Bulk Materials Standards I. GENERAL: This standard is intended to provide specifications for the procurement of Caterpillar Model 938H Wheel Loaders that meet specific area operational

More information

Portable Lighting Equipment Operating Instructions Table of Contents

Portable Lighting Equipment Operating Instructions Table of Contents Portable Lighting Equipment Operating Instructions Table of Generac Magnum Ingersoll Rand TEREX AMIDA TEREX GENIE Model: MLT3060 Model: LIGHTSOURCE Model: Amida AL4000 series Model: TML4000N Generac Magnum

More information

Troubleshooting Guide

Troubleshooting Guide Troubleshooting Guide P/N 0153180 July 1999 P.O. Box 1160 St. Joseph, MO 64502-1160 1-800-255-0317 Fax: 816-360-9379 www.snorkelusa.com GENERAL INFORMATION This manual contains procedures for locating

More information

CDL Series Pre-Trip Inspection AT-TC3TS T1-JA01. Pre-Trip Inspection Checklist

CDL Series Pre-Trip Inspection AT-TC3TS T1-JA01. Pre-Trip Inspection Checklist Pre-Trip Inspection Checklist This checklist covers different parts of the vehicle you would check before a trip. Note that some specifications described in the following content may not be the same as

More information

PowerLevel s e r i e s

PowerLevel s e r i e s Owner s Manual Hydraulic Leveling CONTENTS Introduction Operation Control Panel Automatic Leveling Manual Leveling Retracting Jacks Remote Operation Care & Maintenance Troubleshooting Error Codes 1 2 2

More information

SECTION 3.00 WARNING WARNING ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION

SECTION 3.00 WARNING WARNING ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION SECTION 3.00 ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION Be sure that the clutch, circuit breaker, or other main power transmission device is disconnected. Generators develop voltage as soon as the

More information

PNEUMATICS CONTENTS HST-TAMPER

PNEUMATICS CONTENTS HST-TAMPER CONTENTS Tamper Pneumatic Component Locations...2 Manually Releasing Air Brakes... 3 Releasing Air Pressure... 4 Removing Water from Air Tanks... 4 Adjusting Air Compressor Governor... 4 Check/Replace

More information

PRE-TRIP INSPECTION CDL SKILLS TEST

PRE-TRIP INSPECTION CDL SKILLS TEST CDL SKILLS TEST PRE-TRIP INSPECTION Engine Compartment +1 Axle Side and Back of Truck +1 Axle Connections and Trailer +1 Axle External Light Check In-Cab with Brake Check 1810 N WATKINS RD, WATKINS, CO

More information

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual FORM NO. 8 Rev A Wheel Horse Snowthrower for 5xi Lawn and Garden Tractors Model No. 7966 890050 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information

More information

LA County Fire Department Pre -Trip Inspection Class B Vehicles

LA County Fire Department Pre -Trip Inspection Class B Vehicles LA County Fire Department Pre -Trip Inspection Class B Vehicles Pre Trip Inspection This slide program was designed to assist firefighter s s with their pre trip inspection This slide program comes with

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

MODEL: 310A and 3108 Tractor, Loader and Backhoe Volume 1 of 2

MODEL: 310A and 3108 Tractor, Loader and Backhoe Volume 1 of 2 John Deere MODEL: 310A and 3108 Tractor, Loader and Backhoe Volume 1 of 2 THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS

More information

John Deere. MODEL: 4230 Tractor Volume 1 of 2 JD-S-TM1056

John Deere. MODEL: 4230 Tractor Volume 1 of 2 JD-S-TM1056 John Deere MODEL: 4230 Tractor Volume 1 of 2 THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR

More information

Department of Motor Vehicles Loudoun County Public Schools School Bus Inspection Study Guide Hand Out

Department of Motor Vehicles Loudoun County Public Schools School Bus Inspection Study Guide Hand Out Department of Motor Vehicles Loudoun County Public Schools School Bus Inspection Study Guide Hand Out During the actual tests, you will be expected to point or touch each of the parts of your vehicle.

More information

2016 EQUIPMENT CATALOG

2016 EQUIPMENT CATALOG 2016 EQUIPMENT CATALOG Side by Side Shaker We are the oldest existing manufacturer of Side by Side Harvesters in the United States. We have used a lifetime of farming and harvesting knowledge to develop

More information

Main Fire Pump Engagement. Shifting Into Pump 2006 / 2007 KME

Main Fire Pump Engagement. Shifting Into Pump 2006 / 2007 KME Main Fire Pump Engagement Shifting Into Pump 2006 / 2007 KME 1 Battery Switch Ensure battery switch is turned on to BOTH. 2 Ensure Maxi (Parking) Brake Set Maxi (Parking) Brake must be set or the Pump

More information

RMS. RMS18 Scaler SERIES -LP15 RMS SERIES SALES SPECIFICATIONS OPTIONS FEATURES & BENEFITS

RMS. RMS18 Scaler SERIES -LP15 RMS SERIES SALES SPECIFICATIONS OPTIONS FEATURES & BENEFITS RMS SERIES SALES SPECIFICATIONS RMS SERIES -LP15 RMS18 Scaler FEATURES & BENEFITS AT A GLANCE Weights & Dimensions: Operating Weight Overall Tramming Length Overall Width ~ 45,365lb (20,700kg) ~ 34 (10.3m)

More information

Maintenance and Repair

Maintenance and Repair Maintenance and Repair WARNING ALWAYS shut off the engine, remove key from ignition, make sure the engine is cool, and disconnect the spark plug and positive battery terminal from the battery before cleaning,

More information

A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS

A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS TYPE OF INSPECTION UNDER THE HOOD GASOLINE AND DIESEL 1 Fuel, oil, exhaust leaks - inspect 2 Oil and fuel lines inspect for kinks and wear 3 Automatic transmission

More information

PRICE LIST ITEM PRICE $ CORE

PRICE LIST ITEM PRICE $ CORE A/C Clutch $20.00 A/C Compressor $35.00 $10.00 A/C Condenser $25.00 $5.00 A/C Evaporator $15.00 A/C Hose(S) $15.00 Accelerator Cable $10.00 Air Bag $30.00 Air Bag Sensor $10.00 Air Cleaner $15.00 Air Filter

More information

TUFF TORQ TRANSAXLE. Tuff Torq Hydrostatic Transaxle. Transaxle Removal Tuff Torq

TUFF TORQ TRANSAXLE. Tuff Torq Hydrostatic Transaxle. Transaxle Removal Tuff Torq Tuff Torq Hydrostatic Transaxle Internal Service 3. Disconnect the cotter pin and the washer to the brake rod (Figure 63). Internal service information is contained in the Tuff Torq KGIA Transaxle Service

More information

145 HP, FRONT WHEEL ASSIST TRACTOR 3/17/15 Page 1. Mountrail County Road and Bridge SPECIFICATIONS FOR

145 HP, FRONT WHEEL ASSIST TRACTOR 3/17/15 Page 1. Mountrail County Road and Bridge SPECIFICATIONS FOR Page 1 Mountrail County Road and Bridge S FOR Bidder's Instructions: Indicate compliance to the specifications on the YES/NO line by each specification. Indicate any deviations from the specifications

More information

FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES

FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES 0747-506 1 2506-107 1 Rack, Front - Assembly (inc. 2) 2 0411-576 1 Decal, Warning - Load 3 0441-592 4 Bushing 4 8410-835 4 Screw, Cap 5 0423-669 4 Spacer

More information

MODEL: 6600, Sidehill 6600, and 7700 Combines

MODEL: 6600, Sidehill 6600, and 7700 Combines John Deere MODEL: 6600, Sidehill 6600, and 7700 Combines THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE

More information

John Deere. MODEL: 450-C Crawler JD-O-OMT71338

John Deere. MODEL: 450-C Crawler JD-O-OMT71338 John Deere MODEL: 450-C Crawler THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY

More information

REPAIR MANUAL AFX8010

REPAIR MANUAL AFX8010 REPAIR MANUAL AFX 1 27/05/2004 Contents INTRODUCTION DISTRIBUTION SYSTEMS POWER PRODUCTION POWER TRAIN TRAVELLING BODY AND STRUCTURE TOOL POSITIONING CROP PROCESSING A B C D E G K AFX 1 27/05/2004 INTRODUCTION

More information

Pre-Purchase Inspection Report

Pre-Purchase Inspection Report Inspecting Shop Name Address Phone Shop Foreman Mechanic Year Make Model Vin Color Miles Engine ECM Horsepower Torque Transmission Engine Brake 3 stage Rear Ends Model Ratio Differential Lock Steering

More information

Replacement parts to fit FORD ALPHABETICAL INDEX

Replacement parts to fit FORD ALPHABETICAL INDEX ALPHABETICAL INDEX A Adaptor, Hydraulic, 247, 249 to 250 Adaptor, PTO Shaft, 210 Air Cleaner, 157 to 158 Bowl, 157 Door, 273 Gasket, 159 Hose, 159 Spring, 158 Tube, 158 Air Conditioning Compressors, 282

More information

32 quarts Transmission Allison HT 740 Automatic Fluid

32 quarts Transmission Allison HT 740 Automatic Fluid BOOK: Blue Book I SECTION: E-One Engine (SGT) Page 1 of 6 E-ONE CYCLONE TABLE OF CONTENTS SPECIFICATIONS... 2 DAILY CHECKS... 2 SAFETY CHECKS... 3 START ENGINE... 3 STOP ENGINE... 3 EMERGENCY SHUTDOWN

More information

WEBER CARBURETOR TROUBLESHOOTING GUIDE

WEBER CARBURETOR TROUBLESHOOTING GUIDE This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful

More information

CLASS B PRE-TRIP VEHICLE INSPECTION

CLASS B PRE-TRIP VEHICLE INSPECTION Warren County ESC 320 E. Silver Street Lebanon, OH 45036 April 1, 2006 CLASS B PRE-TRIP VEHICLE INSPECTION A vehicle inspection test evaluates your ability to inspect important parts of a commercial vehicle.

More information

440 & 443 Skid Steer

440 & 443 Skid Steer Bobcat 440 & 443 Skid Steer THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF BOBCAT OR IT S SUCCESSORS. BOBCAT AND IT S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY

More information

GROUNDSMASTER. 52 Recycler. for 120 Traction Unit. Model No & UP. Operator s Manual

GROUNDSMASTER. 52 Recycler. for 120 Traction Unit. Model No & UP. Operator s Manual FORM NO. 8-980 Rev A GROUNDSMASTER 5 Recycler for 0 Traction Unit Model No. 077 79000 & UP Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety

More information

2. PREPARATION 1. SAFETY 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT Monosem Inc.

2. PREPARATION 1. SAFETY 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT Monosem Inc. TABLE OF CONTENTS 1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT For the initial preparation of the planter, lubricate the planter and row units. Make sure

More information

Commander 15i Container and Pallet Loader. Property of American Airlines

Commander 15i Container and Pallet Loader. Property of American Airlines Commander 15i Container and Pallet Loader Section 2. Operation BEFORE ATTEMPTING TO OPERATE OR MAINTAIN THE VEHICLE, COMPLETELY READ AND UNDERSTAND THE OPERATION AND MAINTENANCE MANUAL, INCLUDING ALL DANGER,,

More information

Deicer Operating Instructions Table of Contents

Deicer Operating Instructions Table of Contents Deicer Operating Instructions Table of Contents FMC FMC FMC/Trump FMC Global Premier Trump Model: LA1000 Model: LMD-2000 Model: T2000 Model: TM1800 Model: 2100TE Model: HC29050 Model: D240 Contents FMC

More information

133x152 TWO PRODUCT RAMBLER. 133x152 TRACK MOUNTED IMPACT CRUSHER. Two Bars Per Row. 150mm x 320mm Bearing With Big Cast Base. Each Hammer lbs.

133x152 TWO PRODUCT RAMBLER. 133x152 TRACK MOUNTED IMPACT CRUSHER. Two Bars Per Row. 150mm x 320mm Bearing With Big Cast Base. Each Hammer lbs. Construction Equipment Co. 2 5 1 x 3 3 1 Feeder Size 58 x 18 CAT 600hp Impactor 133x152 Track Mobile Impactor Features Heavy Duty Rotor 4 x 8 Backing Bar With Replaceable Seats 14 Steel Rotor Core Dual

More information

ProLine. 44 Mower. for 120 Traction Unit. Model No & Up. Operator s Manual

ProLine. 44 Mower. for 120 Traction Unit. Model No & Up. Operator s Manual FORM NO. 9 ProLine Mower for 0 Traction Unit Model No. 05 99000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety of others. Also become

More information

Troubleshooting Guide

Troubleshooting Guide Troubleshooting Guide diesel - gasoline - LPG P/N 0172021 June 1999 P.O. Box 1160 St. Joseph, MO 64502-1160 1-800-255-0317 Fax: 816-360-9379 www.snorkelusa.com GENERAL INFORMATION This manual contains

More information

DVX 90 MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM

DVX 90 MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM 2008 DVX 90 Illustrated Parts Manual MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM TABLE OF CONTENTS Black-Red (Model No. A2008KSB2BUSD) Black-Cat

More information

John Deere. MODEL: 2030 Tractor JD-S-TM10S1

John Deere. MODEL: 2030 Tractor JD-S-TM10S1 John Deere MODEL: 2030 Tractor THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY

More information

Universal Super Shield & Ultimate Aluminum w/electric Drive Conversion Kits , , Installation Instructions

Universal Super Shield & Ultimate Aluminum w/electric Drive Conversion Kits , , Installation Instructions WLH 09/19/16 111-0215 & 112-0215 607-0026 For technical support call us at (800) 368-3075 or visit our website at PullTarps.com. TABLE OF CONTENTS ***Assembly*** Conversion Kit-Universal Super Shield ***Wiring,

More information

PRE-TRIP Inspection. CDL Skills Test

PRE-TRIP Inspection. CDL Skills Test CDL Skills Test PRE-TRIP Inspection Engine Compartment +1 Axle Side and Back of Truck +1 Axle Connections and Trailer +1 Axle External Light Check In-Cab with Brake Check 7505 Dahlia St. Commerce City,

More information

WINDSHIELD WIPERS AND WASHERS

WINDSHIELD WIPERS AND WASHERS JA WINDSHIELD WIPERS AND WASHERS 8K - 1 WINDSHIELD WIPERS AND WASHERS CONTENTS page GENERAL INFORMATION MULTI-FUNCTION SWITCH... 1 WINDSHIELD WASHERS... 2 DESCRIPTION AND OPERATION WINDSHIELD WASHERS...

More information

Tests & Adjustments - General Machine. General Safety Hydraulic Tank Turbo Boost Regulator

Tests & Adjustments - General Machine. General Safety Hydraulic Tank Turbo Boost Regulator Section 8.1 Tests & Adjustments - General Machine General Safety......................................... 8.1.2 Hydraulic Tank Turbo Boost Regulator........................ 8.1.2 Hydraulic Tank Safety

More information

Pre-Trip Inspection Bus, School Bus.

Pre-Trip Inspection Bus, School Bus. Pre-Trip Inspection Bus, School Bus. CHECK OUTSIDE IN FRONT OF YOUR VEHICLE (Front of Vehicle, Lights/Reflectors, Engine Compartment & Steering Components) 1. Clearance lights, alternately flashing amber

More information

Other employees or individuals are not allowed to start, pre-trip, or drive the bus without permission from the Transportation Office.

Other employees or individuals are not allowed to start, pre-trip, or drive the bus without permission from the Transportation Office. Pre-Trip Inspection January 27, 2014 Drivers Pre-Trip Inspection The Virginia State Department of Education and Virginia Department of Motor Vehicles REQUIRE a pre-trip inspection. A check must be put

More information

Riding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09

Riding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09 Riding Mowers Z44 and Z52 Accu-Z Razor (S/N 472620 and above) 23802 357-044SM Service Manual 2006 Printed 9/24/09 Copyright 2006 All rights Reserved Land Pride provides this publication as is without warranty

More information

Vehicle Inspection Study Guide TRUCK/TRAILER (PINTLE HOOK)

Vehicle Inspection Study Guide TRUCK/TRAILER (PINTLE HOOK) Department of Motor Vehicles Vehicle Inspection Study Guide TRUCK/TRAILER (PINTLE HOOK) During the actual tests, you will be expected to point to or touch each of the parts of your vehicle listed below.

More information

Oregon Fuel Injection

Oregon Fuel Injection Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear

More information

Troubleshooting the Transmission Hydraulic System

Troubleshooting the Transmission Hydraulic System Testing and Adjusting IT28F INTEGRATED TOOLCARRIER POWER TRAIN Testing And Adjusting Introduction Reference: For Specifications with illustrations, refer to SENR5974, IT28F Integrated Toolcarrier Power

More information

Post Driver Attachment

Post Driver Attachment Attachment (Shown with Optional Power Cell Rotator) Models - 600, 850 Safety Instructions This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully

More information

Service Manual Trucks

Service Manual Trucks Service Manual Trucks Group 88 500 Cab Suspension VN, VHD PV776-TSP4552 Foreword The descriptions and service procedures contained in this manual are based on designs and methods studies carried out up

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all)

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all) HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number 500089, 500105, 500210, 500456, 500535 or no number at all) Visit us on the web at www.lci1.com 82-L0040-01 Rev. 1 WARNING

More information

951B Traxcavator S/n 79H, 32F, 69H & 86J Volume 1 of 2

951B Traxcavator S/n 79H, 32F, 69H & 86J Volume 1 of 2 Caterpillar Service Manual 91B Traxcavator S/n 79H, 2F, 9H & 8J Volume 1 of 2 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR

More information

User s Manual. Automatic Switch-Mode Battery Charger

User s Manual. Automatic Switch-Mode Battery Charger User s Manual Automatic Switch-Mode Battery Charger IMPORTANT Read, understand, and follow these safety rules and operating instructions before using this battery charger. Only authorized and trained service

More information

VPS SERIES. Vibratory Pick Scaler - LP15 AT A GLANCE. OPTIONS 12-8 (3.86 m) FEATURES & BENEFITS

VPS SERIES. Vibratory Pick Scaler - LP15 AT A GLANCE. OPTIONS 12-8 (3.86 m) FEATURES & BENEFITS VPS SERIES - LP15 Vibratory Pick Scaler 285 VP RIES VPS SE LP15 FEATURES & BENEFITS AT A GLANCE Weights & Dimensions: Operating Weight VPS16: 45,160 lb (20,527 kg) VPS25: 46,500 lb (21,136 kg) Overall

More information

H A R D E R D u m p B o x S p r e a d e r

H A R D E R D u m p B o x S p r e a d e r Serial Number: XXXXX O p e r a t o r s M a n u a l Model H A R D E R D u m p B o x S p r e a d e r Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 9 Pg. 10 Pg. 10 INDEX Hydraulic Requirements Safety Safety

More information

ATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 1 of 56 AIR INTAKE ASSEMBLY

ATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 1 of 56 AIR INTAKE ASSEMBLY 2011 ATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 1 of 56 AIR INTAKE ASSEMBLY 2011 ATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 2 of 56 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-705

More information

WHEEL LOADER WHEEL LOADER. ZW series Parallel linkage tool carrier version

WHEEL LOADER WHEEL LOADER. ZW series Parallel linkage tool carrier version ZW series Parallel linkage tool carrier version WHEEL LOADER WHEEL LOADER Model Code: ZW140PL / ZW150PL / ZW1PL Operating Weight: ZW140PL: 11 950-12 010 ZW150PL: 13 370-13 400 ZW1PL: 15 240-15 430 Bucket

More information

ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY

ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY 2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY 2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005

More information

Inline 6 series turbocharger with exhaust gas recirculation (EGR) and selective catalytic reduction (SCR) Valves per Cylinder 4

Inline 6 series turbocharger with exhaust gas recirculation (EGR) and selective catalytic reduction (SCR) Valves per Cylinder 4 SPECIFICATIONS Engine Manufacturer and Model John Deere PowerTech PSS 6090 Non-Road Emission Standards EPA Final Tier 4/EU Stage IV Configuration Inline 6 series turbocharger with exhaust gas recirculation

More information

Road Service Quick Reference Guide 2017 Land Rover Discovery. Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746

Road Service Quick Reference Guide 2017 Land Rover Discovery. Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746 Road Service Quick Reference Guide 2017 Land Rover Discovery Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746 March 31, 2017 Index Quick Specifications and Information 2

More information

RELEASING PRESSURE IN THE HYDRAULIC SYSTEM,

RELEASING PRESSURE IN THE HYDRAULIC SYSTEM, Testing And Adjusting Introduction NOTE: For Specifications with illustrations, make reference to SPECIFICATIONS for 225 EXCAVATOR HYDRAULIC SYSTEM, Form No. SENR7734. If the Specifications are not the

More information

Wheel Horse. 42 Mower. for Lawn and Garden Tractors. Model No & Up. Operator s Manual

Wheel Horse. 42 Mower. for Lawn and Garden Tractors. Model No & Up. Operator s Manual FORM NO. 9 559 Rev A Wheel Horse 4 Mower for Lawn and Garden Tractors Model No. 78 890000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the

More information

Operations Manual for the BJ Series Genco

Operations Manual for the BJ Series Genco Operations Manual for the BJ Series Genco 7 June 2009 Second Edition Genco Mine Service 630 North 400 East Huntington, Utah 84528 Phone 1-800-662-1257 fax 1-435-687-9256 7 8 Genco Pickup Operators Manual

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking

More information

FBC CODES AND TRANSLATIONS TRANSLATION

FBC CODES AND TRANSLATIONS TRANSLATION FBC CODES AND TRANSLATIONS CODE TRANSLATION 500 air cleaning system checked 501 air cleaner housing found cracked 502 repaired cracked air cleaner housing 503 renewed air cleaner housing 504 air intake

More information

BOLT-ON AND WELD-ON FLUSH FLOOR SLIDEOUT SYSTEMS OPERATION AND SERVICE MANUAL

BOLT-ON AND WELD-ON FLUSH FLOOR SLIDEOUT SYSTEMS OPERATION AND SERVICE MANUAL BOLT-ON AND WELD-ON FLUSH FLOOR SLIDEOUT SYSTEMS OPERATION AND SERVICE MANUAL TABLE OF CONTENTS SYSTEM...... Warning........ Description...... Prior to Operation OPERATION... Main Components... Mechanical...

More information

T6 Owners Manual. Basic Function

T6 Owners Manual. Basic Function T6 Owners Manual Basic Function The T6 is a frameless aluminum end dump trailer. It is used mainly for hauling sand, gravel and dirt. The material is discharged by extending the hoist which raises the

More information

Sofa Slideout Assembly OWNER'S MANUAL. Rev: Page 1 Sofa Slideout Owners Manual

Sofa Slideout Assembly OWNER'S MANUAL. Rev: Page 1 Sofa Slideout Owners Manual Sofa Slideout Assembly OWNER'S MANUAL Rev: 06.14.2016 Page 1 Sofa Slideout Owners Manual TABLE OF CONTENTS Warning, Safety, and System Requirement Information 3 Product Information 3 Prior to Operation

More information

2. PREPARATION 1. SAFETY 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT

2. PREPARATION 1. SAFETY 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT TABLE OF CONTENTS 1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT For the initial preparation of the planter, lubricate the planter and row units. Make sure

More information

X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY

X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,

More information

AIR BRAKES THIS SECTION IS FOR DRIVERS WHO DRIVE VEHICLES WITH AIR BRAKES

AIR BRAKES THIS SECTION IS FOR DRIVERS WHO DRIVE VEHICLES WITH AIR BRAKES Section 5 AIR BRAKES THIS SECTION IS FOR DRIVERS WHO DRIVE VEHICLES WITH AIR BRAKES AIR BRAKES/Section 5 SECTION 5: AIR BRAKES THIS SECTION COVERS Air Brake System Parts Dual Air Brake Systems Inspecting

More information

LIFT TRUCK SPECIFICATIONS

LIFT TRUCK SPECIFICATIONS LIFT TRUCK SPECIFICATIONS RT50 2-Wheel Drive 4-Wheel Drive RT60 2-Wheel Drive 4-Wheel Drive RT80 2-Wheel Drive 4-Wheel Drive TABLE OF CONTENTS RT50 / RT60 / RT80 2-WD / 4WD Specifications / Dimensions.

More information

LUBRICATION AND MAINTENANCE

LUBRICATION AND MAINTENANCE DN LUBRICATION AND MAINTENANCE 0-1 LUBRICATION AND MAINTENANCE TABLE OF CONTENTS LUBRICANTS... 1 MAINTENANCE SCHEDULES... 3 JUMP STARTING, TOWING AND HOISTING... 8 LUBRICANTS TABLE OF CONTENTS SERVICE

More information

ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY

ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY 2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY 2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005

More information

S/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly

S/N 1H019H - 1H310H Page 1 of 33 46 Cutting Deck Assembly 1180 S/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly 1180 S/N 1H019H - 1H310H Page 2 of 33 46" Cutting Deck Assembly 1 17982 1 S Reinforcement Spindle Plate 2 618-0430 1 S Spindle Assembly w/

More information

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5 Install Headlight (900, 0, 05) (Figure 5). Remove headlight from location under dash panel. Keep nut for installation.. Attach headlight to bolt on right side of the dash. Fasten with nut removed in step..

More information

TC Series Cooling Systems

TC Series Cooling Systems TC Series Cooling Systems Table of Contents Table of Contents...1 List of Figures...1 Safety...2 Introduction...2 General Specifications...2 Types of Coolant...2 Routine Maintenance...2 Surge Tank Coolant

More information

Section 3 Technical Information

Section 3 Technical Information Section 3 Technical Information In this Module: Engine identification Modes of operation Battery charging and heat manage operation Service and repair procedures Maintenance requirements Engine Identification

More information

Routine Compressor Maintenance

Routine Compressor Maintenance Establishing a regular, well-organized maintenance program and strictly following it is critical to maintaining the performance of a compressed air system. One person should be given the responsibility

More information

Pavement Services, Inc.

Pavement Services, Inc. MG68 Parts Manual Pavement Services, Inc. Page 30 29 30 29 25 25 24 30 4 26 29 4 25 26 4 Page 2 The Decal Kit for the Model MG68 Maintainer is Item Part # Description 056859 DECAL, ANTI-FREEZE (BLACK)

More information

PARTS AND SERVICE MANUAL FOR LEVELING SYSTEMS WITH TOUCH PAD PART NUMBERS , , , , or no number at all

PARTS AND SERVICE MANUAL FOR LEVELING SYSTEMS WITH TOUCH PAD PART NUMBERS , , , , or no number at all PARTS AND SERVICE MANUAL FOR LEVELING SYSTEMS WITH TOUCH PAD PART NUMBERS 500089, 500105, 500210, 500456, 500535 or no number at all Visit us on the web at www.powergearus.com! 82 L0051 00 Rev. 3 1 WARNING

More information

Illustrated Parts Manual

Illustrated Parts Manual 1 10 Illustrated Parts Manual 2 425 CR EFT Model Number A2011IRK4CETR (Red) S H A R E O U R PA S S IO N. TM TABLE OF CONTENTS 2011 ATV 425 CR EFT Red (A2011IRK4CETR) FRONT RACK, BODY PANEL, AND HEADLIGHT

More information

LOADING THE TDRT WARNING LOADING/UNLOADING OPERATION

LOADING THE TDRT WARNING LOADING/UNLOADING OPERATION 0012.3 00 LOADING THE TDRT WARNING LOADING/UNLOADING OPERATION All persons not involved in the loading or unloading operation must stand clear the full length of prime mover and Tilt Deck Recovery Trailer.

More information

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior

More information

NSGV PT-1000 PORTABLE WELDING STATION I, O & M MANUAL

NSGV PT-1000 PORTABLE WELDING STATION I, O & M MANUAL APPLICATION OF DUST CONTROL EQUIPMENT: CAUTION - Warning Improper operation of dust control system may contribute to conditions in the work area or facility that could result in severe personal injury

More information

INSPECTION/ADJUSTMENT

INSPECTION/ADJUSTMENT 3 3 INSPECTION/ADJUSTMENT SERVICE INFORMATION----------------------------------------------------------------------- 3-1 MAINTENANCE SCHEDULE-------------------------------------------------------------------

More information

Road Service Quick Reference Guide Jaguar XF. Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746

Road Service Quick Reference Guide Jaguar XF. Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746 Road Service Quick Reference Guide 2016-2017 Jaguar XF Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746 March 31, 2017 Index Quick Specifications and Information 2 Start/Stop

More information