ASSEMBLY INSTRUCTIONS FOR CHARGER AND THE BOSS QUICK ATTACH GRASS BAGGER
|
|
- Anne Hopkins
- 5 years ago
- Views:
Transcription
1 ASSEMBLY INSTRUCTIONS FOR CHARGER AND THE BOSS QUICK ATTACH GRASS BAGGER \ \ \ \ ~\ P P (7/2005)
2 TABLE OF CONTENTS SECTION PAGE WARNING 1 BLOWER PULLEY INSTALLATION 2 ENGINE GUARD REMOVAL BOSS 3 ACCESSORY MOUNT INSTALLATION BOSS 4 ENGINE GUARD REMOVAL CHARGER 5 ACCESSORY MOUNT INSTALLATION CHARGER 6 BAGGER PULLEY ASSEMBLY 7 BAGGER MOUNT ASSEMBLY 8 MOUNTING GRASS BAGGER TO LAWN MOWER 9 BAGGER DOOR DUMP HANDLE ASSEMBLY 10 BLOWER TO HOPPER & EXTENSION PIECES 11 BLOWER TO BAGGER MOUNT 12 BLOWER TO BAGGER MOUNT FRONT 13 BELT INSTALLATION & ADJUSTMENT 14 WIRING HARNESS INSTALLATION 15 CHARGER WIRING HARNESS TO HOUR METER 16 BOSS WIRING HARNESS TO HOUR METER 17 FRONT WEIGHT KIT INSTALLATION 18 TRANSITION MOUNTING 19 QUICK CHANGE OVER PROCEEDURE 20 BAGGER REMOVAL & MOUNTING 21 P-12102
3 Do not operate grass collector or mower without all guards and safety decals in place. Refer to the owners manual for safe and proper use of the mower. 1) Make sure all guards, shields, and deflectors are in place and in good working condition. 2) Make sure all decals are present and readable. Part no. s are listed in the parts book section located at the back of this manual. 3) Examine flexible tubing for rips or worn places before each use. Make sure hose clamps at each end of the flexible tubing are tight. 4) Make sure transition is properly mounted and locked into position. Proper attaching of transition to deck is explained in the operation section In this manual 1 P
4 BLOWER PULLEY INSTALLATION 1) First unplug the clutch wire from the wire harness and remove deck drive belt. 2) Then remove the bolt in the end of the crank shaft. When you remove the bolt, flat washer, and lock washer the clutch will slide off of the crank shaft. (NOTE where the stop pin lines up with the notch in the clutch.) 3) Drive the headed spacer out of the clutch. Carefully hang clutch by wires. 4) Check the diameter on the headed spacer and use the appropriate pulley and shaft extension supplied with bagger. 5) Next slide the clutch back on the crank shaft rotating it so the clutch stop pin lines up with the notch in the clutch. Block the clutch up with a wooden block. Put set screw in blower pulley. Clutch Blower Pulley Key 6) Slide the Shaft Extension up into the bore of the clutch, making sure the keyway in the shaft lines up with the key in the clutch. 7) While holding the Extension Shaft up in the Clutch, slide the Blower Pulley over the Shaft, with the set screw down. Insert the Key into the key way and tighten the Set Screw. Flat washer Lock Washer 10) If your mower exhausts to the side this ELBOW and CLAMP is needed to deflect the hot exhaust from the bagger frame. Keep from pointing elbow down as this will burn the grass when stopped and engine idling. Set Screw Shaft Extension Bolt Note: Use metric bolt on Liquid cooled Kawasaki. 8) Secure with (2) 7/16 Flat Washers first, then the Lock Washer, then the Bolt supplied with the kit. Or use existing flat washers. Note: On liquid cooled Kawasaki Engines use the metric bolt. 9) Torque Bolt to 50 foot lbs. NOTE: THERE ARE TWO DRIVE PULLEYS AND TWO EXTENSION SHAFTS TO CHOOSE FROM. USE PROPER PAIR TO MATCH YOUR CLUTCH. 2 P12102
5 ENGINE GUARD REMOVAL BOSS LAWN MOWER ONLY Raise deck to highest position and lock with handle. Loosen spring tension jam nut and remove from end of spring tension bolt. NOTE factory position of tension bolt so it can be returned after assembly of accessory mount. Loosen spring tension bolt until bolt is flush with nut welded to bracket. Their will still be some tension on spring, pull against tension and remove spring tension bolt. Remove 4 bolts holding engine guard on and remove guard. Bolts will be reused when accessory mount is assembled. 3 P-12102
6 ACCESSORY MOUNT INSTALLATION BOSS LAWN MOWER ONLY Assemble accessory mount to frame in lower holes with (4) existing bolts from engine guard, returning spring take up brackets to front bolt left hand side. Hook spring to bracket, pull bracket stretching spring and start tension bolt into bracket loose. Retighten bolt for spring tension to position as noted when removed or adjust until deck lifts up and down comfortably to your strength. Assemble jam nut to tension bolt, tighten while holding tension bolt with wrench. 4 P-12102
7 ENGINE GUARD REMOVAL CHARGER Raise deck to highest position and lock with handle. Use one of the dump rods as a pry tool to remove spring. Remove the clevis pin from the clevis and position clevis over spring under bolt, then reinsert pin and clamp over rod. Pry against bolt and outward until spring comes off end of bolt. Maintain a good grip on rod and keep fingers away from spring. Remove (4) bolts from engine guard and remove guard. Keep bolts to assemble accessory mount. Remove spring bolt for accessory mount application. 5 P-12102
8 ACCESSORY MOUNT INSALLATION CHARGER Assemble accessory mount to mower frame with the bolts from engine guard. Use upper holes in accessory mount for charger. Assemble spring bolt from engine guard to lowest hole in accessory mount. With deck in highest position assemble spring. Using the dump rod open tube end as a tool, position rod through spring end first. Position hollow end over bolt head, keeping pressure on rod pry spring rearward. Push spring down rod as you pry until spring snaps over bolt head. 6 P-12102
9 BAGGER PULLEY ASSEMBLY ACCESSORY MOUNT PULLEY REAR PULLYE BRACKET USE BOTTOM HOLES FOR BOSS MOWERS USE TOP HOLES FOR CHARGER MOWERS FRONT PULLEY BRACKET PULLEY (1) Attach FRONT and REAR PULLEY BRACKETS to the ACCESSORY MOUNT with 5/16 x ¾ long bolts and lock nuts. Secure the PULLEY BRACKETS together with a 5/16 x ¾ long bolt. Use top set of holes for Charger mowers and bottom set of holes for Boss mowers. (2) Install (2) PULLEYS, as shown, with long end of bearing toward brackets. Then a thin series ½ flat washer followed by ½ x 1-1/2 long bolt. The nuts go on the inside of the brackets. 7 P-12102
10 11 BAGGER MOUNT ASSEMBLY (1) Lay box on its side and slide bagger out on the ground. (2) Stand bagger on its top, making the underside reinforcements accessible. (3) Unpack parts box to get left and right hand mounts. (4) You will find hardware in a pack and will need (4) 3/8 flat washers and (4) lock nuts. (5) Assemble mounts as shown, and secure nuts with 9/16 socket or wrench. 8 P12102
11 MOUNTING GRASS BAGGER TO LAWN MOWER Back mower into bagger. Refer to air cleaner instructions before lifting bagger into place. Position lower mounting arms with U shaped mounts over bar of accessory mount attached to mower. Assemble clevis pins through holes in U shaped mounting arms and assemble, flat washer and rue pin. For safety purposes tie a rope or chain around bagger and tie or hook to arm rest brackets, while lifting bagger up into position. Tie or hook bagger before the upper arm bushing holes are to the holes on the accessory mount, giving you adjustment movement to be able to lift bagger and line up holes. Assemble T-Handle pins through bushings on upper mounting arms, into bushings on accessory mount, on lawn mower. Untie bagger. 9 P-12102
12 BAGGER DOOR DUMP HANDLE ASSEMBLY Install (2) dump handles, as shown, with 3/8 pins through the bottom holes in the door. Place the 2 nd hole in the dump handles over the 3/8 pins protruding from the dump rod, as shown. Adjust the dump handles, on the threaded end, until the door is tightly closed when the arms on the dump rod are parallel with the dump handles. Install a rue ring on each pin to hold the dump handle on. Adjust stop bolt until the dump rod locks over center to hold the door closed. Install plastic handle over left dump handle by putting some Rubbing Alcohol inside the handle. Hammer together FOAM TAPE STOP BOLT DOOR HINGE BOLT STOP PLATE PIVOT STUD DUMP HANDLE PLASTIC HANDLE RUE RING 10 P-12102
13 BLOWER TO HOPPER & EXTENSION PIECES Get blower & (2) bolts ¼-20x3/4 (2) nuts & position to hopper tipping edge into extension plate. Assemble bolt & nuts loose to hold blower up in position. Get blower extension top & (8) ¼-20x3/4 bolts & ¼-20 nuts. Assemble extension top to extension right & left & blower loose. With 7/16 socket & wrench secure blower to extensions right, left & top. Do not tighten the carriage bolts at the hopper until belt has been insalled. 11 P-12102
14 BLOWER TO BAGGER MOUNT Get a 5/16 bolt & flat washer. Secure bottom left side of blower to rear mount leg. ' /16-1 8x3/4" Flat Washer 5/16" DfT... ' " SGJIlE,,, 12 P-12102
15 Remove Top Belt Guard, ",1; Flat Washer I 0)" ' / ~ BLOWER TO BAGGER MOUNT FRONT * Assemble 5I16-18x314 boll & flat washer through RH front mount leg & through front bell guard. * Assemble 5116 nykx:k. nut loose. This will be tightened after belt is aslembled and tension is adjusted., // ;1, ~~yiock Nut Page 13 P-12102
16 BELT INSTALLATION & ADJUSTMENT 1) Install the Adjustment screw (5/16-18 x 4 ) and flat washer into the hole in the Adjustment tab and down through the rear belt guard. Install a flat washer and a lock nut on the bottom of the Adjustment screw 2) MAKE SURE THE DECK BELT IS ON NOW. 3) Install V-Belt over pulley on the Clutch and down around the (2) Idler pulleys. Route the belt around The Engine pulley as shown. Check for proper twist in belt from one v-pulley to the next. Note: 75 belt on Boss mowers and 72 belt on Charger mowers 4) Tighten the Adjustment screw until you can flex the belt 3/8 to 3/4 at the mid point. 5} When the belt tension is correct, tighten the (6) bolts and nuts that connect the blower to the frame and hopper. ADJUSTMENT TAB ADJUSTMENT SCREW CLUTCH V-BELT IDLERS 14 P-12102
17 WIRING HARNESS INSTALLATION 1) Remove nut from toggle switch. 2) Insert the Toggle switch through the hole in the right frame, as shown, with the groove in the threaded stud to the top and secure with nut. 3) Route the Clutch wire through the frame, as shown. Secure the clutch wire away from the belt By passing it through the Kurly loc. 4) The Bagger Connector is used only when installing and removing the bagger. 5) Unplug the red wire on the hour meter of the tractor. Plug the single red wire from the switch into the hour meter, where you removed the old wire. Plug the old wire into the tab on the new red wire. Use wire ties to fasten the red wire to the throttle cable. 6) Unplug the connector to the deck clutch, in front of the engine. Plug in the connectors from the switch wire harness into the (2) ends you just unplugged. Use wire ties to tie the wire harness away from the engine where possible. 7) Secure all loose wires with wire ties. 8) With wiring complete, secure the Belt cover over the Front and rear belt guards with (2) 1/4x3/4 bolts, locks Washers, and flat washers. TOGGLE SWITCH With groove in threaded stud to the top. NUT BAGGER CONNECTER TO DECK CLUTCH TO ENGINE TO HOUR METER See page 16 BELT COVER CLUTCH WIRE KURLY-LOC 15 P-12102
18 CHARGER WIRING HARNESS TO HOUR METER Remove cover under right hand armrest, (3) bolts. Pull red double wire from hour meter spade. Connect red single blower wire with jumper to hour meter. Reconnect double red to jumper connection on blower wire. Reassemble cover with (3) bolts and secure. Cover Hour Meter Red Double Wire on Hour Meter Blower Wire with Jumper 16 P-12102
19 BOSS WIRING HARNESS TO HOUR METER Remove cover under right hand arm rest, (4) bolts. Pull red double wire from hour meter spade. Connect red single blower wire with jumper to hour meter spade. Reconnect double red to jumper connection on blower wire. Reassemble cover with (4) bolts and secure. Cover Hour Meter Red Double Wire on Hour Meter Blower Wire With Jumper 17 P-12102
20 FRONT WEIGHT KIT INSTALLATION NOTE: MOWERS REQUIRE 3 WEIGHTS AND APPROPRIATE BRACKETS. 1) Mount (two) weight mount brackets to the axle behind the caster pivot tubes using (four) carriage bolts 3/8-16 x 3, (two) plate mounts and (four) 3/8-16 nyloc nuts. Locate these back away from the pivot tube far enough to allow it to caster properly. 2) Weights can be set into the brackets from the top and secured with (two) (3/8 bolts 6 long with nuts.) WEIGHTS 3/8-16 X 6 BOLT CARRIAGE BOLT, 3/8-16 X 3 BRACKET, WEIGHT MOUNT NUT PLATE, WEIGHT MOUNT NUT, 3/8-16 X NYLOC 18 P-12102
21 1) Rotate the discharge chute up as far as possible. TRANSITION MOUNTING 2) Remove, and discard, the bolts, washers, and nuts from the center (2) holes on the discharge stiffener. 3) Place the transition angle and the transition saddle over the (2) holes and lightly secure with (2) 5/16 x 1-1/4 carriage bolts, lock washers and plain nuts. The saddle goes on top of the angle. TRANSITION 4) While holding the transition with round hole to the back of the mower, lift the outside of the transition up slightly, and insert the lip of the transition under the open chute and into the angle and the saddle. 5) The adjustment plate allows the transition to fit either the 52 or the 60 deck. Lightly tighten the (2) ¼ bolts, lock washers, and washers with the adjustment plate as far back as it will go to start. After the adjustments on the transition are made, then adjust the adjustment plate forward until it comes in contact with the back of your deck. Tighten the bolts at this time. ADJUSTMENT PLATE 5) Once the lip on the transition is in the angle and saddle, rotate outside end down until the top of the transition is parallel with the top of the deck. The rod on the end of the transition should fall into the hole in deck at this point. If not, loosen the (2) nuts on the end of the transition, and move the rod around until it falls into the hole. Tighten the (2) nuts by the rod. If the nuts holding down the angle and saddle have been left loose, they should be located by now. Tighten the (2) nuts. The lip on the transition should fit tightly into the saddle and angle. If it is loose, adjust, and retighten. 6) Once the nuts are all tight, pull the rod out of the hole, and remove the transition. Reinstall the transition several times to make sure all adjustments are correct. Slight pressure up or down on the transition will help the rod fall into place easier. HOSE CLAMP LIP TRANSITION SADDLE DECK DISCHARGE STIFFENER HOSE TRANSITION LOOSEN THESE NUTS TO ADJUST ROD ASSEMBLY TRANSITION ANGLE ROD (2) HOLES HOLE IN DECK Place one of the hose clamps on each end of the hose. With the clamps loose, slide the hose on the transition, and the intake of the blower about 1-1/2. Tighten the clamps. Read and understand owners manual completely before using grass bagger. 19 P-12102
22 QUICK CHANGE OVER PROCEDURE To change from mowing with the grass bagger to mowing side discharge follow this procedure. HOLDING BRACKER FOR TRANSITION 1) Disengage the deck by pressing down the deck switch. 2) Remove the transition from the discharge end of the deck. 3) Swing the transition up and over the blower and slide the transition (opening facing up), onto the holding bracket mounted on the blower. (there are (2) slots in the transition that slide onto the (2) hooks on the bracket.) 4) Flip the discharge chute down to resume side discharge. 5) To go from side discharge to grass bagging reverse process. DUMPING AND CLEANOUT 1) When hopper is full, push dump handle down. Slight forward and reverse movement of the mower helps free debris that does not readily come out. To close door and resume mowing, lift dump handle up and lock over center. SLOTS IN TRANSITION 20 P-12102
23 BAGGER REMOVAL & MOUNTING A On models with Kohler engines, first remove the standard engine air cleaner before removing or Mounting BAGGER B PROCEDURE FOR REMOVING GRASS BAGGER 1) Disconnect the connector in the wire harness. 2) For safety purposes, before pulling T-Handle pins out, first tie a length of rope or chain around one side of the frame and over one of the seat arm rests to keep the bagger from falling over backwards. 3) Pull the (2) T-Handle pins out of the front of the bagger and mount. By forcing the bagger forward The belt can be rolled off of the engine pulley. 4) While holding the bagger in the up position, remove the rope, and simply lay the bagger down. 5) Remove the (2) Rue rings. Flat washers and Clevis pins and drive away. 6) Replace air cleaner. C TO MOUNT GRASS BAGGER 1) Back mower into bagger and reverse procedure. 2) On Boss mowers it may be necessary to place a 2 X 4 under bagger to help align legs with mounting bracket. RUE RING T-HANDLE PIN FLAT WASHER CLEVIS PIN 21 P-12028
POWER LIFT PARTS LIST ASSEMBLY INSTRUCTIONS SAFETY AND OPERATIONS P (02/15)
POWER LIFT PARTS LIST ASSEMBLY INSTRUCTIONS SAFETY AND OPERATIONS P-0 (0/) COUNTRY CLIPPER POWER LIFT Part Number: GI-00A Approved to be installed on the following Model Year 0 and newer models: * All
More informationCollection System. Please read the operator s manual carefully and make sure you understand the instructions before using the machine.
Collection System 967004601 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. 2012 All rights reserved. Swainsboro, GA. Printed in U.S.A.
More information62 Deck Idler Kit High Speed
Part No. 00 FORM NO. -899 6 Deck Idler Kit High Speed For Model 70 Serial No. 99000 to 99000 For Model 7 Serial No. 9900 to 99000 INSTALLATION INSTRUCTIONS Loose Parts Note: Use the chart below to identify
More informationSafety First. Please remember to always use SAFE shop practices when performing all service procedures.
Safety First Please remember to always use SAFE shop practices when performing all service procedures. 2006 Update Manual January 2006 Country Clipper 2006 Update Manual Index Joystick Kill Switch Oil
More informationGrass Catcher. Instructional / Parts Manual Part Number: January ( & ) & Drive Kits ( , , )
Grass Catcher Instructional / Parts Manual Part Number: January 200 5020 ( 507 & 5026 ) & Drive Kits ( 52030, 5203, 52032) Table of Contents Z RIDER GRASS CATCHER TWO PACKAGED ITEMS LIST 507 BLOWER ASSEMBLY
More informationDFS Vac Collection System 400 Series Z Master
Form No. 0 DFS Vac Collection System 00 Series Z Master Model No. 780 Serial No. 000000 and Up Operator s Manual Register your product at www.toro.com Original Instructions (EN/GB) Contents Page Introduction................................
More informationRepair Parts Manual For: SR-125. Zero Turn Radius Mower P (4/11)
Repair Parts Manual For: SR-125 Zero Turn Radius Mower P-12763 (4/11) COUNTRY CLIPPER WRANGLER - SR125 ZERO TURN RADIUS MOWER TABLE OF CONTENTS MOWER DECK... SPINDLE ASSEMBLY... RUBBER CHUTE ASSEMBLY...
More informationRepair Parts Manual for: SR-125. Zero Turn Radius Mower P (9/11)
Repair Parts Manual for: SR-125 Zero Turn Radius Mower P-12843 (9/11) COUNTRY CLIPPER WRANGLER - SR125 ZERO TURN RADIUS MOWER TABLE OF CONTENTS 41" MOWER DECK... 48" MOWER DECK... SPINDLE ASSEMBLY... RUBBER
More informationENCORE 52" X-TREME. 2-BAG GRASS CATCHER for units w/ S/N and above ASSEMBLY AND PARTS DIAGRAMS
ENCORE 52" X-TREME 2-BAG GRASS CATCHER for units w/ S/N 53138 and above ASSEMBLY AND PARTS DIAGRAMS Notes: ASSEMBLY INSTRUCTION Figure 1 Using 1/2" wrench, remove the discharge cover and the RH deck belt
More information52 inch Twin Bagger and Finishing Kit 200 Series Z Master
Form No. 9 68 inch Twin Bagger and Finishing Kit 00 Series Z Master Model No. 7898 Serial No. 000000 and Up Model No. 780 Operator s Manual English (EN) Contents Page Introduction................................
More informationAdjustments manual for: Gear Drive, ETS Gear Drive, Walk Hydro, ETS Walk Hydro, Mini Rider, Large Rider Gen 2
For Husqvarna Parts Call 66-678-96 or 66-56-98 Adjustments manual for: Gear Drive, ETS Gear Drive, Walk Hydro, ETS Walk Hydro, Mini Rider, Large Rider Gen MANUAL NO. 5957 REV. (//) For Husqvarna Parts
More informationINSTALLATION INSTRUCTIONS FOR: DECK LIFT KIT 629GN-001A
INSTALLATION INSTRUCTIONS FOR: DECK LIFT KIT 629GN-001A 1. SHUT OFF THE ENGINE AND SET THE PARK BRAKE. 2. ROTATE THE FRONT CASTER WHEELS AWAY FROM THE DECK. (SEE ILLUSTRATION 3) 3. REMOVE THE DECK HEIGHT
More informationParts Manual Zero Turn Mower / Z 248F
Parts Manual Zero Turn Mower / Z 248F 967262501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support
More informationPlease read the operator manual carefully and make sure you understand the instructions before using the machine.
967327901-00 Parts Zero Manual Turn Mower Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service
More informationAgri-Fab OWNERS MANUAL. Model No " ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-0362 CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts 42" ROUGH CUT TRAILMOWER NOTE: Your mower deck will
More informationCALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL
CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More information312000x98A Lawn Tractor (2002) Page 1 of 19 Chassis & Hood
312000x98A Lawn Tractor (2002) Page 1 of 19 Chassis & Hood 312000x98A Lawn Tractor (2002) Page 2 of 19 Chassis & Hood 1 690566 Seat 2 028X23 Cap, Push On 3 094057 Spring 4 26X229 Screw 5 1001054 Bolt,
More informationWorldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE Toll Free Number:
Operator s Manual R WYZ48/52/60CS BAGGER Worldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE 68310 Toll Free Number: 1-800-267-4255 OPERATOR S MANUAL This catcher manual is for
More informationItem No. Part Number Description Qty
36 Frame Assembly 1 336-001 Hood 36" 1 2 100-009 Saucer Nut 4 3 300-001 Rear Deck Weldment 1 4 200-006 Nylon Nut M10 GB889-86 9 5 200-003 Hexagon Bolt M10*25 GB5783-86 12 6 100-007 Chute Deflector 1 7
More informationOWNERS MANUAL. Model No. LST42G 42" SNOW THROWER. Safety Assembly Operation Maintenance Parts
OWNERS MANUAL Model No. LST42G 42" SNOW THROWER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com
More information107086_0607. Hustler Z BAC-VAC Owner s Manual
107086_0607 Hustler Z BAC-VAC Owner s Manual TABLE OF CONTENTS 1. General Information...Sect. 1 2. Safety Precautions...Sect. 2 3. Assembly Instructions...Sect. 3 4. Operation...Sect. 4 5. Maintenance...Sect.
More informationGRASS CATCHER PART S & OPERATORS MANUAL
GRASS CATCHER PART S & OPERATORS MANUAL WORLDLAWN POWER EQUIPMENT, INC. WORLDLAWN.COM 2415 ASHLAND AVE BEATRICE, NE 68310 800-267-4255 FAX 402-223-4103 2 3 4 OPERATORS MANUAL This catcher manual is for
More informationParts Manual MZ5225 /
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Parts Manual MZ5225 / 966690502 Please
More informationM-ZT 61. Parts Manual. Zero Turn Mower /
Parts Manual M-ZT 61 Zero Turn Mower / 967177008-01 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support
More informationWas Giant- Vac Part # Part # Description BAG- GRASS 15.4X16X22.5 WHITE POLY CLTH OBS HANGER- GRASS BAG HOOP 10GA TWIN -
Was Giant- Vac Part # Part # Description 1703764 484811 BAG- GRASS 15.4X16X22.5 WHITE POLY CLTH OBS 1703807 484880 HANGER- GRASS BAG HOOP 10GA TWIN - PLAIN 1703855 484881 HOOP-.500DIA 16.12X16.75 GRASS
More informationDIAMONDBACK/EDGE GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL
DIAMONDBACK/EDGE GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL GRASS CATCHER W/WEIGHT: TUBE KIT: BLOWER KIT: 48 5101305 632093 632078 52 5101305 542119 632074 60 632086 542120 632081 3 WORLDLAWN POWER
More informationINSTALLATION INSTRUCTIONS
PZ 60 inch Side Discharge Deck Kit - 966555302 Tools Required ½" socket or wrench (battery terminals, strut shaft). ½" breaker bar with 2-3" extension (relieve tension on idler arms). Refer to Operators
More informationMZ 52LE. Parts Manual. Zero Turn Mower /
Parts Manual MZ 52LE Zero Turn Mower / 9677406-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support
More informationParts Manual MZ52 /
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Parts Manual MZ52 / 962401 Please
More informationParts Manual Rev. A
115 96 28-27 Rev. A Parts Manual Z 242F / 967 271802-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More informationEasy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,
More informationParts Manual Rev. A
115 97 25-27 Rev. A Parts Manual Z 242F / 967 844702-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationParts Manual WH3615/ WH4817/ WH5217/ English
Parts Manual WH6/66400 WH48/664002 WH2/66400 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. English 2008 HTC. All rights reserved. Beatrice,
More informationKING COBRA/CALIBER GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL
KING COBRA/CALIBER GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL GRASS CATCHER W/WEIGHTS: TUBE KITS: BLOWER KITS: 52 542128 52 542119 5101002 60 542129 60 542120 5101003 2 WORLDLAWN POWER EQUIPMENT
More informationParts Manual Zero Turn Mower / Z 254i
Parts Manual Zero Turn Mower / Z 254i 967324201-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support
More informationParts Manual Rev. 3
114 08 93-27 Rev. 3 Parts Manual Z 254F / 967954001-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More information44 and 52 Twin Bagger 100 Series Z Master
Form No. 7 87 and 5 Twin Bagger 00 Series Z Master Model No. 7855 Serial No. 000000 and Up Operator s Manual English (CE) Contents Page Introduction................................ Safety.....................................
More informationQUICKSILVER 54 LAWN MOWER
1701 38TH AVE W PO BOX 229 SPENCER, IA 51301 FAX: 712-22-028 SERVICE: 800-81-2222 E-MAIL: ccac@cyclecountry.com QUICKSILVER 5 LAWN MOWER OWNER S AND OPERATORS MANUAL KIT NUMBER 30-0025 (Briggs Engine)
More informationAgri-Fab OWNERS MANUAL. Model No " ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-03071 45-0361 CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts 42" ROUGH CUT TRAILMOWER the fastest way
More information62ZB. 62 BEAST Zero Turn Riding Mower. Kawasaki FX850V Engine
62ZB 62 BEAST Zero Turn Riding Mower Kawasaki FX850V Engine 62ZB Deck Parts Diagram Key Item # Gxi Part Number Description 1 SP11-000063 Belt guard, 62ZB, set of 2 with rubber T-handle receivers 2 SP12-000229
More informationRM42G MOWER Deck and Chute... 5 Spindles, Belts and Pulleys... 7 Mounting Brackets and Axle... 9 Decals... 39, 41
RM42G RM38, RM44, RM48 R Ingersoll RM42G MOWER Deck and Chute... 5 Spindles, Belts and Pulleys... 7 Mounting Brackets and Axle... 9 Decals... 39, 41 RM38, RM44, RM44GR, RM48 MOWER Deck, Belts, Backside
More informationParts & Owner s Manual
Havener Enterprises, Inc. 368 S. Michigan Ave. Bradley, IL 60915 815.935.8383 32, 36, 48 & 52 Commercial Belt-Drive Mowers Parts & Owner s Manual Congratulations on the purchase of your new Bradley mower.
More informationOWNERS MANUAL. Model No. LST42D 42" SNOW THROWER. Safety Assembly Operation Maintenance Parts
OWNERS MANUAL Model No. LST42D 42" SNOW THROWER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com
More informationService Manual. Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Service Manual Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY This Service Manual is not a substitute for the Operator s Manual. You must read, understand and
More informationSCION tc STRUT TIE BAR Preparation
SCION tc 2005 - STRUT TIE BAR Preparation Part Number: 00016-80440 Code: YY1 Kit Contents 1 1 DS Mount Plate 2 1 PS Mount Plate 3 1 Cross Bar 4 1 Hardware Bag Hardware Bag Contents 1 4 8mm Screws 2 4 8mm
More informationParts Manual Zero Turn Mower / Z
Parts Manual Zero Turn Mower / Z 254 967324101-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support
More informationParts Manual PZ Please read the operator manual carefully and make sure you understand the instructions before using the machine.
Parts Manual PZ 60 967 045601-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service questions,
More informationStowe Cargo Management System
Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages
More informationLOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT
LOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT P/N 2881235; 2881236; 2881237 APPLICATION All AXYS and PRO RIDE chassis with stock Pro-Taper Bar BEFORE YOU BEGIN Read these instructions and
More informationParts Manual. Field and Brush Mower. 16HP Tractors. 13.5HP Tractors. 13HP Tractors. 15HP Tractors
Parts Manual Field and Brush Mower.5HP Tractors Mfg. No. Description 20.5HP, Walk-Behind Brush Mower (Simplicity) 25.5HP, Walk-Behind Brush Mower (Ferris GM25H) 25.5HP, Walk-Behind Brush Mower (Giant-Vac
More informationParts Manual Zero Turn Mower / Z
Parts Manual Zero Turn Mower / Z 246 967271501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support
More informationParts Manual Rev. A
115 97 79-27 Rev. A Parts Manual Z 248F / 967 844801-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More informationParts Manual Rev. A Z 246 /
115 97 16-27 Rev. A Parts Manual Z 246 / 967 844501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More information53cm Recycler Rear Bagger Walk Power Lawn Mower
Form No. 3327 713 53cm Recycler Rear Bagger Walk Power Lawn Mower Model No. 20789 210000001 and Up Model No. 20791 210000001 and Up Parts Catalog Ordering Replacement Parts To order replacement parts,
More informationHYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).
TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all
More informationParts Manual Rev. B RZT48 /
115 91 36-2 Rev. B Parts Manual RZT48 / 96 62001-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of 10%
More information57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions For Model: MR55H KUNZ ENGINEERING, INC. / MENDOTA, IL / PH (815) /07
57 ROUGH CUT OWNER S MANUAL With Assembly Instructions For Model: MR55H KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954 1/07 ASSEMBLY INSTRUCTIONS Read the complete assembly instructions
More information57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions For Models: MR55T, MR55B & MR55K
57 ROUGH CUT MR55K MR55B OWNER S MANUAL With Assembly Instructions For Models: MR55T, MR55B & MR55K KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954 1/05 ASSEMBLY INSTRUCTIONS Read the complete
More information57 ROUGH CUT WITH ELECTRIC CLUTCH BLADE ENGAGEMENT OWNER S MANUAL. With Assembly Instructions For Model: MR55KE
57 ROUGH CUT WITH ELECTRIC CLUTCH BLADE ENGAGEMENT OWNER S MANUAL With Assembly Instructions For Model: MR55KE KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954 01/05 ASSEMBLY INSTRUCTIONS
More information36 Tiller Wheel Horse Lawn and Garden Tractor Attachment
Form No. 9 6 Rev B 6 Tiller Wheel Horse Lawn and Garden Tractor Attachment Model No. 797 890000 and Up Operator s Manual English(En) Contents Page Introduction................................ Safety.....................................
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration
More information465606x692A Lawn Tractor (2001) Page 1 of 25 Drive Assembly
465606x692A Lawn Tractor (2001) Page 1 of 25 Drive Assembly 465606x692A Lawn Tractor (2001) Page 2 of 25 Drive Assembly 1 26X249 Screw 2 095315 Knob, Parking Brake 3 711691 Nut, Push 4 1001217 Z Rod, Parking
More informationMfg. No: P216020KWV, 21" 6 TP Steel Deck Series
Parts Manual Mfg. No: 7800557 P216020KWV, 21" 6 TP Steel Deck Series Copyright Briggs and Stratton. All Rights reserved 28-Sep-2018 Model Components Table Of Contents Page Accessory Recycling Kits..............................................................................
More information57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions. For Models: MR55T, MR55B-17.5HP, MR55B-22HP & MR55K
57 ROUGH CUT MR55K MR55B OWNER S MANUAL With Assembly Instructions For Models: MR55T, MR55B-17.5HP, MR55B-22HP & MR55K KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954 1/07 ASSEMBLY INSTRUCTIONS
More informationSection 5: Parts Replacement
Section 5: Parts Replacement Should the STAR TRAC 4500 Treadmill experience a problem requiring replacement of a specific part, the following procedures will help and instruct in the replacement of major
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Read the complete assembly instructions before starting the assembly. You should have: - one mower deck assembly - two carrier arm assemblies - two rear tire assemblies - one ATV
More informationFIELD & BRUSH MOWER SERIES 0
Parts Manual for SERIES 0 MODEL FB13250BS FB13250BV FB15250KW McDonough, GA, 30253 U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 1, 8/30/2005 Table Of Contents PAGE GROUP
More informationWARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.
WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationParts Manual
0-- JSE 0 0- Parts Manual Z F / 00-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of % ethanol (E) is
More informationPRO HYDRO WALK BEHIND MOWERS MID-SIZE SERIES 3
Parts Manual for MID-SIZE SERIES 3 POWER UNIT MODELS SPLH153KW SPLH173KW MOWER MODELS SPA361 SPA481 SPA521 SPA611 McDonough, GA, 30253 U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED.
More informationProcedure Replacing a Cover
Procedure 7.1 - Replacing a Cover Cover Removal 1. Remove two screws, one each side, from the front of the top cover. Remove the top cover. See Diagram 7.1. Diagram 7.1 - RBK 815 Covers Top Cover Left
More informationQuiet Collector. Model No & Up
FORM NO. -8GB Rev A Quiet Collector Model No. 795-890000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety
More informationPlease read the operator manual carefully and make sure you understand the instructions before using the machine.
967327801-00 Parts Zero Manual Turn Mower Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service
More informationQuiet Collector. Model No & Up
FORM NO. -0 Quiet Collector Model No. 79-990000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety of others.
More information235/245400, , 28N
Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters
More informationIt don t mean a thing If it ain t got the swing
SWING CHUTE SAND/SALT SPREADER INSTALLATION AND OPERATING INSTRUCTIONS SWING CHUTE SPREADER MODELS: 7, 8, 9, 9.5 & 10 MANUAL FOR SPREADER SERIAL NUMBERS AFTER # 20000 It don t mean a thing If it ain t
More informationCUTTER DECK. * Purchase part Shear Bolt Package to replace these parts. (4 of each per package)
0 0 0 0 CUTTER DECK 0 0S00 CUTTER DECK Foot Plate 00-0 Serr. Fl. Hex Nut, /- -0 Grease Fitting Frame, Cutter Deck Support (incl.,,) 00-0 Hex Locknut, Elastic Stop, /- 0 Rod, Deck Prop - L.H. 00- Serr.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationZ Master. 62 Mower. for Z Master Z 255 Traction Unit. Model No & UP. Operator s Manual
FORM NO. 9 88 Z Master 6 Mower for Z Master Z 55 Traction Unit Model No. 7408 89000 & UP Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety
More informationInstallation Guide. Stowe Cargo Management System. Table of Contents
Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages
More informationIllustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060
Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part #891-561C (Gandy Part #6245DS-GP) For Great Plains Turbo-Max 2400, 3000, 3500 & 4000 Models 45
More informationLawn Mower. 22in Recycler. Parts Catalog. Form Number Rev A. Model No and up.
Form Number 3358-999 Rev A 22in Recycler Lawn Mower Model No. 20067-280000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity, and
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More information72K850ZP PARTS MANUAL
7 2 K 8 5 0 Z P PARTS MANUAL 72 MID-CUT GAS ENGINE OPTION SECTION 72 MID-CUT DECK ASSEMBLY 72" Mid-Cut Deck Assembly # PART NO. QTY DESCRIPTION 1 582096 1 72" MC DECK WELDMENT 2 582098 1 72" DECK CHANNEL
More informationCollection System Operators Manual Model: Parts Manual
Collection System Operators Manual Model: 113706 Parts Manual Please read these instructions carefully and make sure you understand them before using the machine. MANUAL NO. 539 113763 REV 01 (09/18/06)
More informationMOWER HOUSING SUSPENSION
MODEL 000xA MOWER HOUSING SUSPENSION 0 0 0 0 F 00L MODEL 000xA MOWER HOUSING SUSPENSION Knob 00 Washer 0x Pad, Friction 0 Pin, Hanger 0 Link, Lift 00E00 Nut, Flange 0x Bolt, Shoulder 00x Bracket, Rear
More informationParts Manual SPEEDZTR 30 /
Parts Manual SPEEDZTR 30 / 966676201 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable
More informationCHASSIS & HOOD ASSEMBLY
- TS01906 CHASSIS & HOOD ASSEMBLY 25 5 4 19 8 9 9 11 4 11 3 10 11 5 11 2 11 11 1 17 21 18 16 11 3 21 12 22 3 7 2 CHASSIS REAR PG. ENGINE & CONTROL PG 24 3 1 23 6 7 KEY #22 344695A 1 CHASSIS & HOOD ASSEMBLY
More informationParts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODEL SPE1250KW SPE140KW SPE150KH SPE151KW SPEL150KH
Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODEL SPE10KW SPE0KW SPE10KH SPE11KW SPEL10KH MOWER UNIT MODEL SPE30 SPE480 SPE31 SPE481 IT IS POLICY OF SNAPPER TO
More informationPage1. ISF Stainless Steel Headers // Part# HDR-004
Congratulations on the purchase of your ISF Stainless Steel Headers and thank you for choosing Sikky Manufacturing. This installation manual is intended to guide you through the removal of the factory
More informationParts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 MODELS
Parts Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 18 PUSH MODELS 216518B PROPELLED MODELS EP217018BV ERP217018BV P216018KWV P216518B P217018BV P217018BVE RP216018KWV RP217018BV RP217018BVE McDonough,
More informationParts Manual Rev. A RZT54 /
115 93 37-27 Rev. A Parts Manual RZT54 / 967 672101-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More informationSuspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
More informationSTOP 42"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts
Operator's Manual STOP 42"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT Model No. 486.248381 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product,
More informationContents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment
Contents Section 5: Adjustments... 5-3 1. Ball Detect Adjustment... 5-3 2. Transport Band Tension Adjustment... 5-5 3. Transport Band Drive Belt Tension Adjustment... 5-7 4. Ball Cushion Adjustment...
More information25 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower
MMZ 2, 260 2 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower ILLUSTRATED PARTS LIST " Float Cutter Deck - Figure 1 3 1 27 32 17 6 1 11 31 36 3 19 7 23 1 33 38 18 37 22 3 20 2 10 2 12 21 30 39
More information