POE1824B. PoE 27,6V/4x0,4A/2x7Ah/PoE

Size: px
Start display at page:

Download "POE1824B. PoE 27,6V/4x0,4A/2x7Ah/PoE"

Transcription

1 v.1.0 PoE 27,6V/4x0,4A/2x7Ah/PoE Buffer switch mode power supply unit EN* Edition: 2 from Supercedes the edition: 1 from

2 Features: DC 27,6 V/4x0,4A uninterruptible power supply fitting battery: 2x 7Ah/12V wide range of mains supply: V high efficiency 77% battery charging and maintenance control excessive discharging (UVP) protection battery charge current 0,2A battery output full protection against short-circuit and reverse polarity connection intended for operation in 10Mbit/s and 100Mbit/s networks voltage control at the AUX1 AUX4 outputs AW output of the PSU failure, tripped by: short-circuit (SCP) overload (OLP) LED indication protections: SCP short-circuit protection OVP over voltage protection overtension protection against sabotage OLP overload protection warranty 2 year from the production date CONTENTS: 1. Technical description. 1.1 General description 1.2 Block diagram 1.3 Description of PSU components and connectors. 1.4 Specifications 2. Installation. 2.1 Requirements 2.2 Installation procedure 3. Operating status indication. 3.1 LED indication of operating status 3.2 Technical outputs 4. Operation and use. 4.1 Overload or short circuit of the PSU output 4.2 Disconnection of discharged battery 4.3 Maintenance 1. Technical description. 1.1 General description A buffer PSU is intended for an uninterrupted supply to mx. 4 net camcoders requiring stabilised voltage of 24 V DC (+/-15%). The PSU provides voltage of U=27,6 V DC with current capacity: I=4x0,4A + 0,2A battery charge. In case of power decay, a battery back-up is activated immediately. The PSU is constructed based on the switch mode PSU, with high energy efficiency. The PSU is housed in a metal enclosure (colour RAL 9003) which can accommodate two 2x7Ah/12V batteries. A micro switch indicates door opening (front cover). Supply to the camcorders is by means of network cabling, with twisted pairs 4/5 (+) and 7/8 (-), which, in accordance with the Ethernet network standard, are not intended for data transmission (data transmission uses 1/2 and 3/6 twisted pairs). The PSU cannot be used in Gigabit Ethernet networks, where all twisted pairs take part in a data transition. The power supply is also adapted to the mounting of the DCDC20 (5V 18V/2A 1,3A) converter. During normal operation, the total current drawn by the receivers may not exceed I = I,6 A. Maximum battery charging current: 0.2 A. Total device current + battery: 1,8 A max. 2

3 1.2 Block diagram. 1.3 Description of PSU components and connectors. Fig. 1. Block diagram of the PSU. Table 1. Elements of the PSU pcb (refer to Fig. 2). Element no. (Fig. 2). [1] [2] Description IN module supply AW - technical output of the PSU operating status OC type (open collector) level hi-z = status: failure level L = status: correct operation LED indication: green diode indicates voltage at the IN input red diode indicates AW failure [3] connector of the additional, external LED indication [4] network inputs (Ethernet) [5] network outputs (Ethernet + supply) for connecting the camcorders [6] L1 L4 green LEDs: indicate voltage in individual AUX outputs (under normal status, the diodes are permanently illuminated) [7] pins for melting fuse/ptc selection [8] F1, F2, F3, F4 fuses in the AUX (+) circuit Tab. 1. Description of the PoE module components. 3

4 Fig. 2. Lay-out of the elements. Fig.3. The view of the PSU. 4

5 Fig.3. The view of the PSU. Table 2. Elements of the PSU (refer to Fig. 3.) Element no. Fig. 3. Description [1] Switch-mode power supply unit [2] LED indicating PSU operation [3] P1 potentiometer, output voltage adjustment [4] PoE module [5] Battery connectors +BAT = red, - BAT = black [6] TAMPER against sabotage protection contact (NC) 1.4 Specifications: - electrical parameters (tab.3) - mechanical parameters (tab.4) - operation safety (tab.5) - operating parameters (tab.6) Electrical parameters (tab. 3) Mains supply V AC Current up to 0,6A@230V AC Power frequency 50 60Hz Supply power 50W max. Efficiency 77% Output voltage 27,6 V DC buffer operation 19V 27,0V DC battery-assisted operation Output current 4x 0,4A + 0,2A battery charge Output current t AMB <30 C 4x 0,4A + 0,2A battery charge - refer to chart 1 Output current t AMB =40 C 4x 0,25A + 0,2A battery charge - refer to chart 1 Voltage adjustment range 24 28V DC Ripple 150 mv p-p max. Battery charging current 0,2A 2x7Ah (± 5%) Short-circuit protection SCP electronic Overload protection OLP 4x F 0,5A or 4x PTC 0,5A Battery circuit protection OLP polymer fuse Overvoltage protection OVP 4x varistor Excessive discharge protection UVP <19,0 V (± 5%) disconnection of the battery terminal Power status LED indication Yes - OC type, 50mA max. Technical outputs: - AW - indicates fuse failure - TAMPER - indicates enclosure opening normal status: level L (0V), failure: level H (hi-z) (automatic recovery after a return to correct operation) - microswitch, NC contacts (enclosure closed), 0,5A@50V DC (max.) F1 F4 fuses F 0,5A /250V or PTC 0,5A Mechanical parameters (tab. 4). Enclosure dimensions 320 x 304 x 90+8 (325 x 309 x 98) (WxHxD) Fixing Refer to Fig. 3. Fitting battery 2 x 7Ah/12V (SLA) max. Net/gross weight 2,50kg / 2,80kg Enclosure Steel plate DC01, thickness: 0,8mm, colour: RAL 9003 Closing Cheese head screw (at the front), x2 Connectors Power-supply: Φ0,4-2,5 (AWG 26-10) Battery outputs : BAT: 6,3F-2,5, 50cm PoE module : Φ0,5-2,5 (AWG 24-12) AUX1...4 outputs: RJ45 8pin TAMPER output: Φ0,8, 50cm Notes The enclosure does not adjoin the assembly surface so that 5

6 cables can be led. Operation safety (tab.5). Protection class PN-EN :2007 I (first) Degree of Protection PN-EN 60529: 2002 (U) IP20 Electrical strength of insulation: - between input and output circuits of the PSU (I/P-O/P) 3000 V/AC min. - between input circuit and PE protection circuit (I/P-FG) 1500 V/AC min. - between output circuit and PE protection circuit (O/P-FG) 500 V/AC min. Insulation resistance: - between input circuit and output or protection circuit 100 MΩ, 500V/DC Operating parameters (tab.6). Operating temperature Storage temperature Relative humidity Vibrations during operation Impulse waves during operation Direct insulation Vibrations and impulse waves during transport -10ºC...+40ºC -20ºC...+60ºC 20%...90%, without condensation unacceptable unacceptable unacceptable Wg PN-83/T Chart 1. Acceptable output current of the PSU depending on ambient temperature. 2. Installation 2.1 Requirements The buffer PSU shall be mounted by a qualified installer with appropriate permissions and qualifications for 230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall be mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max. without condensation) and the temperature from -10 C to +40 C. The PSU shall operate in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the enclosure. Before installation, prepare a PSU load balance. During normal operation, the total current drawn by the device may not exceed I = 1,6A. Maximum battery charging current: 0,2 A. Total device current + battery: 1,8 A max. As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical system shall follow valid standards and regulations. The PSU is intended for operation in Ethernet networks, with capacity of 10Mbit/s or 100Mbit/s (so-called Fast Ethernet). It cannot bee used within the 1000Mbit/s capacity networks (so-called Gigabit Ethernet). The connection between the camcorder and the PSU is to be done with a cable of UTP-3 category (in a network where the data transmission speed amounts to 10Mbit/s) or UTP-5. Due to lower cable resistance, it is recommended to 6

7 use UUPT-5 type cables, also in the networks where the data transmission speed does not exceed 10Mbit/s (especially when there is a significant distance between the PSU and its receiver). 2.2 Installation procedure 1. Before installation, cut off the voltage in the 230V power-supply circuit. 2. Mount the PSU in a selected location and connect the wires. 3. Connect the power cables (~230Vac) to L-N clips of the PSU. Connect the ground wire to the clip marked by the earth symbol PE. Use a three-core cable (with a yellow and green PE protection wire) to make the connection. Lead the cables to the appropriate clips through the insulating bushing of the connection board. The shock protection circuit shall be performed with a particular care, i.e. the yellow and green wire coat of the power cable shall stick to one side of the terminal - marked with symbol on the PSU enclosure. Operation of the PSU without the properly made and fully operational shock protection circuit is UNACCEPTABLE! It can cause a device failure or an electric shock. 4. Connect the network cables (Ethernet) to the PoE module: the supply power appears only in the AUX power outlets, and that is where the camcorders are to be plugged. 5. With F1/PTC1 F4/PTC4 jumpers, select a sort-circuit or overload protection type. A jumper in the Fx position the melting fuse is active, PTCx position the PTC fuse is active. 6. If necessary, make technical connections: - AW - technical output of the PSU operating status, indicates voltage absence at any of the outputs (AUX1 AUX4) - TAMPER - indicates enclosure opening 7. Connect the battery in accordance with the markings (colours) - battery output (+V): BAT+ / red, - battery output (0V): BAT - / black 8. Check the PSU operation indicator: green LED (green on the PoE module) 9. Check the PSU output voltage: - the PSU voltage without load should amount to U=27, 6V DC. 10. Once the tests and operation control have been completed, the enclosure can be locked. 3. Operating status indication. 3.1 LED indication of operating status The PSU is equipped with seven diodes in the front cover. RED LED: on the PSU is supplied with 230V AC off no 230V AC supply RED LED: on DC at the output of the switch-mode PSU off no DC at the output of the switch-mode PSU RED LED: on fuse failure at one of the AUX1 AUX4 outputs off no failure GREEN LED: on DC at the AUX1 AUX4 output off no DC at the AUX1 AUX4 output 7

8 Additionally, the PSU is equipped with LEDs inside the enclosure Fig. 2 and 3. Operating status indication of the switch mode power supply: Green LED indicates correct operation of the switch mode power supply. Indication of voltage at the IN output of the PoE module green LED. Green diodes L1 L4 - indicate voltage at any of the module outputs (L1 for AUX1, etc.) If any of the Lx diodes is off, it means that the shot-circuit or overload protection of a given circuit has been activated. 3.2 Technical outputs: The PSU is equipped with indication outputs which inform about AC power failure or tampering inside the power supply. AW - technical output of the power supply: OC type indicates the PSU failure (short-circuit or overload). In a normal status (under proper operation), the output is fault to ground (status L 0V), in case of In case of power loss, the PSU output is switched into hi-z (high impedance) state. TAMPER - output indicates opening the power-supply unit: output as volt-free (potential-free) contacts which indicate power-supply unit door status, unit closed: NC, unit opened: NO 4. Operation and use. 4.1 Overload or short circuit of the PSU output The AUX1 AUX4 outputs of the connector strip is equipped with an independent short-circuit / overload protection due to melting or polymer fuses PTC (the selection of the fuse is done by a certain positioning of the Fx/PTCx jumper). If the load of the PSU exceeds I max (load 110% of the PSU power), the output voltage is automatically cut off and indicated by the Lx green diode off.. To restore the output power and to protect the PTC, cut off the output load for approximately 1 minute (this amount of time is necessary for the PTC fuse to cool down). If a melting fuse was used for the protection, it shall be replaced by a new one, of the same type and rated current. 4.2 Disconnection of discharged battery. The PSU is equipped with the discharged battery disconnection system. During the battery-assisted operation, reducing voltage below 19V at the battery terminals will cause battery disconnection. 4.3 Maintenance Any and all maintenance operations may be performed following the disconnection of the PSU from the power supply network. The PSU does not require performing any specific maintenance measures, however, in the case of significant dust rate, its interior is recommended to be cleaned with compressed air. Periodically, the battery condition ought to be checked. In case of any faults (capacity loss, too high internal resistance), the battery needs to be exchanged. In case of fuse replacement, use a replacement of the same parameters. 8

9 9

10 WEEE MARK According to the EU WEE Directive It is required not to dispose of electric or electronic waste as unsorted municipal waste and to collect such WEEE separately. The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled according to the applicable law. GENERAL WARRANTY CONDITIONS 1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a two-years warranty for the equipment, counted from the device s production date. 2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the manufacturer s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects, unless such defects have been reported within the warranty period (item 1). 3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the manufacturer. 4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect. 5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenienve, however not later that within 14 days from the delivery to the service centre of the manufacturer. 6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the equipment has been conditionally accepted, due to the breaking warranty terms by the claimant. 7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively. 8. The warranty does not cover the defects of the equipment, resulting from: - reasons beyond the manufacturer's control, - mechanical damage, - improper storage and transport, - use that violates the operation manual or equipment s intended use - fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents, - improper installation and configuration (in defiance with the manual), 9. The warranty is void in any of the following circumstances: - construction changes - repairs carried out by any unauthorized service center - damage or removal of warranty labels - modifications of the serial number 10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the wholesale prices suggested by the manufacturer on the day of purchase. 11. The manufacturer takes no reponsibility for the defects that result from: - the damaging, malfunctioning or inability to operate the equipment - defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the recommendations and requirements contained in the manual, or the use of the equipment. Pulsar K.Bogusz Sp.j. Siedlec 150, Łapczyca, Poland Tel. (+48) , Fax. (+48) biuro@pulsar.pl, sales@pulsar.pl

HPSB 2512B v.1.0 HPSB 13,8V/2A/7Ah Buffer, switch mode power supply unit.

HPSB 2512B v.1.0 HPSB 13,8V/2A/7Ah Buffer, switch mode power supply unit. HPSB 2512B v.1.0 HPSB 13,8V/2A/7Ah Buffer, switch mode power supply unit. EN* Edition: 5 from 05.06.2014 Supercedes the edition: 4 from 10.02.2014 Features: DC 13,8V/2A uninterruptible power supply* fitting

More information

AWZ 200. AWZ 13,8V/2A/7Ah/L

AWZ 200. AWZ 13,8V/2A/7Ah/L GREY POWER AWZ 200 v.2.4 AWZ 13,8V/2A/7Ah/L Linear, Buffer Power Supply Unit EN** Edition: 7 from 15.05.2014 Supercedes the edition: 6 from 13.02.2014 Features: 13,8VDC/2A uninterruptible supply fitting

More information

BNC08128C. BNC 13,8V/8x1A/17Ah. Switch mode buffer power supply unit for CCTV. v.1.0 EN** Edition: 1 from Supersedes the edition:

BNC08128C. BNC 13,8V/8x1A/17Ah. Switch mode buffer power supply unit for CCTV. v.1.0 EN** Edition: 1 from Supersedes the edition: BNC08128C v.1.0 BNC 13,8V/8x1A/17Ah Switch mode buffer power supply unit for CCTV. EN** Edition: 1 from 26.11.2013 Supersedes the edition: ------ GREEN POWER CCTV BNC PSU features: DC 13,8V/8x1A uninterruptible

More information

BNC BNC 12V/8x1A. Switch mode power supply unit for CCTV. v.1.0 EN** Edition: 1 from Supersedes the edition:

BNC BNC 12V/8x1A. Switch mode power supply unit for CCTV. v.1.0 EN** Edition: 1 from Supersedes the edition: BNC08128 v.1.0 BNC 12V/8x1A Switch mode power supply unit for CCTV. EN** Edition: 1 from 26.11.2013 Supersedes the edition: ------ GREEN POWER CCTV BNC PSU features: supply output 8x1A/12V DC output voltage

More information

PSDCB161220E. v.1.0. PSDCB 13,8V/20A/16x1A/65Ah. Buffer power supply for up to 16 HD cameras. EN** Edition: 3 from

PSDCB161220E. v.1.0. PSDCB 13,8V/20A/16x1A/65Ah. Buffer power supply for up to 16 HD cameras. EN** Edition: 3 from PSDCB161220E v.1.0 PSDCB 13,8V/20A/16x1A/65Ah Buffer power supply for up to 16 HD cameras. EN** Edition: 3 from 15.11.2017 Supercedes the edition: 2 from 24.04.2017 GREEN POWER CCTV Features: DC 13,8V/20A

More information

PSU-S-12V/L-1A/5/FTA/PTC-TR-MC AWZ v.1.0

PSU-S-12V/L-1A/5/FTA/PTC-TR-MC AWZ v.1.0 PSU-S-12V/L-1A/5/FTA/PTC-TR-MC AWZ 05121 v.1.0 Linear, stabilized power supply unit. Edition: 1 from the 2 nd February 2011 Supercedes edition: Features of the power supply unit: five outputs protected

More information

PSUPS10A12C. PSUPS 13,8V/12V/10A/17Ah. Buffer power supply for 8 HD cameras and recorder. v.1.0. Supercedes the edition: 1 from

PSUPS10A12C. PSUPS 13,8V/12V/10A/17Ah. Buffer power supply for 8 HD cameras and recorder. v.1.0. Supercedes the edition: 1 from v.1.0 PSUPS 13,8V/12V/10A/17Ah Buffer power supply for 8 HD cameras and recorder EN Edition: 2 from 15.11.2017 Supercedes the edition: 1 from 23.05.2017 GREEN POWER CCTV Features: DC 13,8V uninterruptible

More information

PSBSH 2012B. PSBSH 13,8V/2A/7Ah/HERMETIC

PSBSH 2012B. PSBSH 13,8V/2A/7Ah/HERMETIC PSBSH 2012B v.1.2 PSBSH 13,8V/2A/7Ah/HERMETIC Buffer switch mode power supply unit, EN** Edition: 7 from 02.11.2017 Supercedes the edition: 6 from 08.06.2017 Features: DC 13,8V/2A uninterruptible power

More information

PSU-S-12V/L-3A/9/FTA/PTC-TR-MC AWZ v.1.0

PSU-S-12V/L-3A/9/FTA/PTC-TR-MC AWZ v.1.0 PSU-S-12V/L-3A/9/FTA/PTC-TR-MC AWZ 09123 v.1.0 Linear, stabilized power supply unit. EN Edition: 1 from the 30 th January 2011 Supercedes edition: Features of the power supply unit: 3 groups (A, B, C)

More information

AWZ 110. AWZ 13,8V/1A/7Ah/LM

AWZ 110. AWZ 13,8V/1A/7Ah/LM AWZ 110 v.1.3 AWZ 13,8V/1A/7Ah/LM Linear buffer power supply unit Grade 2. EN* Edition: 9 from 02.11.2017 Supercedes the edition: 8 from 23.01.2017 GREY POWER plus Features: EN50131-6 compliance, 1 2 grades

More information

FIREMAN'S MICROPHONE POWER SUPPLY FOR THE VOICE ALARM SYSTEMS 24V

FIREMAN'S MICROPHONE POWER SUPPLY FOR THE VOICE ALARM SYSTEMS 24V DSOS24V v.1.0 FIREMAN'S MICROPHONE POWER SUPPLY FOR THE VOICE ALARM SYSTEMS 24V EN* Edition: 2 from 30.08.2017 Supercedes edition: 1 from 24.05.2016 PSU features. Compliant with the requirements of the

More information

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain

More information

The 4HR-UPS 220V ac output is provided via a Pure Sine Wave inverter, allowing it to be backed up by 2x 12V standby batteries.

The 4HR-UPS 220V ac output is provided via a Pure Sine Wave inverter, allowing it to be backed up by 2x 12V standby batteries. 1 Elmdene International Ltd Tel: +44 (0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk STANDBY 220V AC POWER SYSTEM IDEAL

More information

Dycon D2430 EN54-4 Fire Alarm Power Supply Series

Dycon D2430 EN54-4 Fire Alarm Power Supply Series Dycon D2430 EN54-4 Fire Alarm Power Supply Series Technical Description Installation and Operating Manual Construction Product Regulation 0359-CPR-00434 Page 1 of 14 Contents 1. General... 3 1.1 Product

More information

Features. Description. Table of Contents

Features. Description. Table of Contents Features Very low profile Very high efficiency (typically 90%) Single and dual output versions Input voltages from 24V to 110VDC nominal voltages from 5V to 48VDC -40 C to +71 C operation without de-rating

More information

Elmdene International Ltd

Elmdene International Ltd 1 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44(0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk 13.8Vdc Switch Mode Power Supply GEN3-08-y

More information

LS200 Series Instruction Manual

LS200 Series Instruction Manual LS200 Series Instruction Manual BEFORE USING THE POWER SUPPLY UNIT Pay attention to all warnings and cautions before using the unit. Incorrect usage may lead to an electrical shock, damage to the unit

More information

USER MANUAL. 10 January Certification of constancy of performance CNBOP No CPR-0454 Certificate of admittance CNBOP No.

USER MANUAL. 10 January Certification of constancy of performance CNBOP No CPR-0454 Certificate of admittance CNBOP No. User Manual ZSP100 Document No. 0658.00.95-03.2 Page 1/6 MERAWEX Sp. z o.o. Toruńska 8 44-122 Gliwice Poland tel. +48 32 23 99 400 fax +48 32 23 99 409 merawex@merawex.com.pl http://www.merawex.com.pl

More information

Switching DC Power Supply

Switching DC Power Supply 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Model 1693, 1694 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary

More information

EVS RP6020. Instruction Manual

EVS RP6020. Instruction Manual Instruction Manual TDK Lambda BEFORE USING THE PRODUCT Be sure to read this instruction manual thoroughly before using this product. Pay attention to all cautions and warnings before using this product.

More information

Features. LED Driver. RACT09 9 Watt. TRIAC Dimmable. Single Output RACT09- AC/DC Converter

Features. LED Driver. RACT09 9 Watt. TRIAC Dimmable. Single Output RACT09- AC/DC Converter Features TRIAC Dimmable LED Driver Triac dimmable with leading or trailing edge dimmers Class II with SELV output (no earth required) Extra-large screw terminals and integrated cable clamps for easy installation

More information

DIN Rail UPS Model: DIN-UPS Installation/Operation Manual

DIN Rail UPS Model: DIN-UPS Installation/Operation Manual DIN Rail UPS Model: DIN-UPS 24-10 Installation/Operation Manual Table of Contents Section Page Section Page Quick Start 2 1) General Information 4 Materials Provided 4 Optional Equipment 4 2) Safety Information

More information

27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2

27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 1 27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 STX2401-C STX2401-T FEATURES 0843-CPR-0213 14 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax:

More information

PSU EN54-4 Power Supplies

PSU EN54-4 Power Supplies PSU EN54-4 Power Supplies Ordering: Models, Sales Order Parts: PSU MXP-549 : 1.5A PSE in 7Ah enclosure MXP-550 : 3.0A PSE in 17/18Ah enclosure MXP-550D : 3.0A PSE in 25Ah enclosure MXP-551 : 5.0A PSE in

More information

D R C- 4 0 s e r i e s

D R C- 4 0 s e r i e s LPS Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 Features Universal AC input / Full range Protections: Short circuit / Overload / Over voltage Battery low protection /

More information

Sola/Hevi-Duty S3K Series Mini-Tower UPS

Sola/Hevi-Duty S3K Series Mini-Tower UPS Sola/Hevi-Duty S3K Series Mini-Tower UPS GUIDE SPECIFICATIONS 700VA to 1600VA 120V models Single - Phase Uninterruptible Power Supply Systems 1.1 SUMMARY 1.0 GENERAL This specification defines the electrical

More information

Uninterruptible power supply Supply MEg101.4

Uninterruptible power supply Supply MEg101.4 Uninterruptible power supply Supply MEg101.4 MEgA Měřící Energetické Aparáty, a.s. 664 31 Česká 390 Czech Republic Uninterruptible power supply Supply MEg101.4 Uninterruptible power supply MEg101.4 1/

More information

User Manual Digital Energy Uninterruptible Power Supply ML Series UPS VA GE Digital Energy Power Quality

User Manual Digital Energy Uninterruptible Power Supply ML Series UPS VA GE Digital Energy Power Quality GE Digital Energy Power Quality User Manual Digital Energy Uninterruptible Power Supply ML Series UPS 350-500-700-1000 VA GE imagination at work GB User Manual Digital Energy Uninterruptible Power Supply

More information

UCS-CHR24V55W. Combined Power Supply & Battery Charger. Data Sheet

UCS-CHR24V55W. Combined Power Supply & Battery Charger. Data Sheet Combined Power Supply & Battery Charger Data Sheet INTRODUCTION UCS-CHR24V55W is a combined charger and power supply with dedicated outputs for both charging and power supply. With a large input range

More information

User Manual. Digital Energy Uninterruptible Power Supply ML Series UPS VA. GE Digital Energy Power Quality. GE imagination at work

User Manual. Digital Energy Uninterruptible Power Supply ML Series UPS VA. GE Digital Energy Power Quality. GE imagination at work GE Digital Energy Power Quality User Manual Digital Energy Uninterruptible Power Supply ML Series UPS 350-500-700-1000 VA GE Consumer & Industrial SA General Electric Company CH 6595 Riazzino (Locarno)

More information

OWNER S MANUAL Please read this manual before operating your power supply

OWNER S MANUAL Please read this manual before operating your power supply AC-DC POWER SUPPLY Switch Mode AC-DC Power Supply Model No. PSU-1210 PSU-1223 PSU-1230 OWNER S MANUAL Please read this manual before operating your power supply Table of Contents Precautions 2 Description

More information

WARNING. This product uses High Brightness LEDs. Direct viewing of the SMD LEDs at close range should be avoided. Keep product away from children.

WARNING. This product uses High Brightness LEDs. Direct viewing of the SMD LEDs at close range should be avoided. Keep product away from children. WARNING Before use please remove the LED Tape from its bag and allow the odour to dissipate in an unused room or outdoor building. Wash Hands after handling. This product uses High Brightness LEDs. Direct

More information

Uninterruptible Power System

Uninterruptible Power System USER'S MANUAL Emergency Backup Power Supply For Use With Computer Loads Only Power Surge/Noise Protection Intelligent Auto-Shutdown Software Internet Line Protection Cost Efficiency UPS 1 st Edition Uninterruptible

More information

DIN Rail UPS DC UPS/Battery Detection System Model: BDS-DIN-UPS Installation/Operation Manual

DIN Rail UPS DC UPS/Battery Detection System Model: BDS-DIN-UPS Installation/Operation Manual DIN Rail UPS DC UPS/Battery Detection System Model: BDS-DIN-UPS 24-10 Installation/Operation Manual Table of Contents Section Page Section Page Quick Start 2 1) General Information 4 Materials Provided

More information

& HIGH CURRENT DC POWER SUPPLIES INSTRUCTION MANUAL

& HIGH CURRENT DC POWER SUPPLIES INSTRUCTION MANUAL 72-6850 & 72-6852 HIGH CURRENT DC POWER SUPPLIES INSTRUCTION MANUAL Table of Contents Introduction 2 Specification 2 Safety 4 EMC 5 Installation 6 Connections 6 Operation 7 Maintenance and Repair 8 www.tenma.com

More information

Model 1900, 1901, 1902 Switching DC Power Supply

Model 1900, 1901, 1902 Switching DC Power Supply Model 1900, 1901, 1902 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all

More information

RP Instruction Manual

RP Instruction Manual Instruction Manual TDK Lambda BEFORE USING THE PRODUCT Be sure to read this instruction manual thoroughly before using this product. Pay attention to all cautions and warnings before using this product.

More information

Model 1693, 1694 Switching DC Power Supply

Model 1693, 1694 Switching DC Power Supply Model 1693, 1694 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all phases

More information

CDBR-B. Dynamic Braking Unit Instruction Manual. April 2009 Part Number: R1 Copyright 2009 Electromotive Systems

CDBR-B. Dynamic Braking Unit Instruction Manual. April 2009 Part Number: R1 Copyright 2009 Electromotive Systems CDBR-B Dynamic Braking Unit Instruction Manual April 2009 Part Number: 146-10001-R1 Copyright 2009 Electromotive Systems 2009 MAGNETEK All rights reserved. This notice applies to all copyrighted materials

More information

CX-SERIES ADVANCED BATTERY CHARGER

CX-SERIES ADVANCED BATTERY CHARGER CX-SERIES ADVANCED BATTERY CHARGER Table of Content 1. IMPORTANT SAFETY INFORMATION... 2 1-1 General Safety Precautions... 2 1-2 Battery Precautions... 2 2. FEATURES... 3 2-1 Battery Charging Curve...

More information

Sinewave Inverters. SWING pro 200VA and 350VA. User s manual

Sinewave Inverters. SWING pro 200VA and 350VA. User s manual Sinewave Inverters SWING pro 200VA and 350VA User s manual 1 Warranty RIPEnergy is not manufacturer of these units. All technical information s, data s and dimension s rely on information s given by the

More information

Battery Booster Pack. Instruction Manual for P/N

Battery Booster Pack. Instruction Manual for P/N Important: Please ensure that you read and save this instruction manual before using this product. Incorrect operation or misuse of this Battery Booster Pack may damage the equipment or create hazardous

More information

Silver T E L E C O M. 1. Features. 2. Description. IEEE802.3af compliant. Small SIL package size - 56mm (L) x 14mm (H) Low output ripple and noise

Silver T E L E C O M. 1. Features. 2. Description. IEEE802.3af compliant. Small SIL package size - 56mm (L) x 14mm (H) Low output ripple and noise Silver T E L E C O M V2.0 Aug 2008 Pb. Features IEEE802.3af compliant Small SIL package size - 56mm (L) x 4mm (H) Low output ripple and noise Input voltage range 36V to 57V Only one low cost external decoupling

More information

Specifications 2019-V AC-DC Din Rail Mounted Power Supply IS-70 Series, 70W

Specifications 2019-V AC-DC Din Rail Mounted Power Supply IS-70 Series, 70W 2019-V1.0-0318 Specifications AC-DC Din Rail Mounted Power Supply IS-70 Series, 70W No. 545 Museum Road Yangzhou, Jiangsu China 225009 Tel: 86 (514) 8279 1592 Fax: 86 (514) 8769 3159 2019 AC-DC Din Rail

More information

i-energy i-micro inverter GT260

i-energy i-micro inverter GT260 i-energy i-micro inverter GT260 This installation guide contains important instructions on safety matters and the installation of the i-energy i-micro inverter GT260. Please read this guide carefully and

More information

Model 1900, 1901, 1902 Switching DC Power Supply

Model 1900, 1901, 1902 Switching DC Power Supply Model 1900, 1901, 1902 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all

More information

Module B Module C FOR THE WEATHER CONTROLLER MULTI-MIX INSTALLATION MANUAL REVISION: 1.0_EN

Module B Module C FOR THE WEATHER CONTROLLER MULTI-MIX INSTALLATION MANUAL REVISION: 1.0_EN Module B Module C FOR THE WEATHER CONTROLLER MULTI-MIX INSTALLATION MANUAL REVISION: 1.0_EN 05-2018 ELECTRIC DEVICE UNDER VOLTAGE! Before any action related to the power supply (cables connection, device

More information

Your new LM controller is a state-of-the art device which was developed in accordance with the latest

Your new LM controller is a state-of-the art device which was developed in accordance with the latest CAP LM-series Solar charge controller User Manual Thank you very much for buying this CAP product. Please read the instructions carefully and thoroughly before using the products. Your new LM controller

More information

Battery Jump Pack. Instruction Manual for P/N Lithium Iron Phosphate (LiFePO4)

Battery Jump Pack. Instruction Manual for P/N Lithium Iron Phosphate (LiFePO4) Important: Please ensure that you read and save this instruction manual before using this product. Incorrect operation or misuse of this Battery Booster Pack may damage the equipment or create hazardous

More information

REMOTE POWERING Central Energy System ( HUB )

REMOTE POWERING Central Energy System ( HUB ) / 0 REMOTE POWERING Central Energy System ( HUB ) User Guide Mitra E&I SCA Wavre Belgium 009 Subject to modifications without notice / 0 Content RECTIFIER SYSTEM - USER MANUAL The information and pictures

More information

miconverter 18-Module Rack-Mount Power Chassis User Manual 38 Tesla, Irvine, CA USA Phone: (949) ; Fax: (949) Page 12

miconverter 18-Module Rack-Mount Power Chassis User Manual 38 Tesla, Irvine, CA USA Phone: (949) ; Fax: (949) Page 12 miconverter 18-Module Rack-Mount Power Chassis User Manual Page 12 38 Tesla, Irvine, CA 92618 USA Phone: (949) 250-6510; Fax: (949) 250-6514 General and Copyright Notice This publication is protected by

More information

DC Master 24/ A

DC Master 24/ A USERS MANUAL DC Master 24/12 50-60A DC-DC converter MASTERVOLT Snijdersbergweg 93, 1105 AN Amsterdam The Netherlands Tel.: +31-20-3422100 Fax.: +31-20-6971006 www.mastervolt.com ENGLISH Copyright 2015

More information

Fuse state indicator MEg72. User manual

Fuse state indicator MEg72. User manual Fuse state indicator MEg72 User manual MEg Měřící Energetické paráty, a.s. 664 31 Česká 390 Czech Republic Fuse state indicator MEg72 User manual Fuse state indicator MEg72 INTRODUCTION The fuse state

More information

Installation Instructions

Installation Instructions AQU244 & AQU128 Series Installation Instructions Installation Instructions AQU244 24vdc 5A Supervised Power Supply/Charger module AQU128 12vdc 10A Supervised Power Supply/Charger module Both Mounted in

More information

AC/DC Converter MBP250-2A13D13M

AC/DC Converter MBP250-2A13D13M 250W, 165-264VAC Input, Dual output AC/DC battery charging module power supply FEATURES Low stand-by power consumption, Maximum instantaneous power up to 350W With charging function, the 12V output Lead-acid

More information

Aurora Wind Interface Box

Aurora Wind Interface Box Aurora Wind Interface Box Installation and Operator s Manual Page 2 of 15 REVISION TABLE Document Revision Author Date Change Description 1.0 T. Melzl 5/9/2006 First release of the document SAVE THESE

More information

Models. Output current max.* Output Power max. Low Line : VAC High Line: VAC 24 VDC / 12 A 240 W. Back up battery

Models. Output current max.* Output Power max. Low Line : VAC High Line: VAC 24 VDC / 12 A 240 W. Back up battery AC/DC Battery Controller Power Supply TSPC-240UPS Series Compact universal 24 VDC power supply with integrated battery controller module Battery protection for over voltage, deep discharge, short circuit

More information

USE AND INSTALLATION HANDBOOK

USE AND INSTALLATION HANDBOOK Date : 10/02/14 Rev. 01 PR.T : FG006172 USE AND INSTALLATION HANDBOOK DUPLEX-UP CONTROL PANEL FOR 2 ELECTRIC PUMPS WITH CURRENT CONTROL. DUPLEX-UP Via Enrico Fermi 8-35020 Polverara PD Tel.049/9772407

More information

Installation manual wall-mounted distributor

Installation manual wall-mounted distributor EN Installation manual wall-mounted distributor EN 60003233 Issue 11.2016 2016-14-11 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2

More information

LC BATTERY CHARGER OPERATION & MAINTENANCE GUIDE

LC BATTERY CHARGER OPERATION & MAINTENANCE GUIDE LC BATTERY CHARGER OPERATION & MAINTENANCE GUIDE SENS part number: 101194 Document revision: D DCN number: 105128 Date: 3/23/2006 1840 Industrial Circle Longmont, CO 80501 Fax: 303-678-7504 Tel: 303-678-7500

More information

Power Supply EL

Power Supply EL General information: EL630-1203-7 has been specifically developed to meet the DC powering requirements for telecommunications, industrial and marine applications. The output is current limited, with short

More information

CDBR-B. Instruction Manual. Dynamic Braking Unit. March 2013 Part Number: R4 Copyright 2013 Magnetek

CDBR-B. Instruction Manual. Dynamic Braking Unit. March 2013 Part Number: R4 Copyright 2013 Magnetek B Dynamic Braking Unit Instruction Manual March 2013 Part Number: 146-10001 R4 Copyright 2013 Magnetek 2013 Magnetek All rights reserved. This notice applies to all copyrighted materials included with

More information

Triple Output High Resolution Power Supply. User Manual

Triple Output High Resolution Power Supply. User Manual 1320 Triple Output High Resolution Power Supply User Manual Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all phases of operation,

More information

ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL

ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL PHASETEC digital power conditioners are designed to safely operate electrical equipment in the harshest power quality environments. With a wide

More information

HYBRID 5048E. Hybrid Inverter INSTALLATION AND OPERATION MANUAL. Version 2.0E

HYBRID 5048E. Hybrid Inverter INSTALLATION AND OPERATION MANUAL. Version 2.0E HYBRID 5048E Hybrid Inverter INSTALLATION AND OPERATION MANUAL Version 2.0E SAFETY INSTRUCTIONS Risk of Electric Shock Alternating Current (AC) and Direct Current (DC) sources are connected to this device.

More information

UPS USER MANUAL F-11 LINE INTERACTIVE UPS GENERAL PURPOSE UPS 650VA/1200VA/2200VA

UPS USER MANUAL F-11 LINE INTERACTIVE UPS GENERAL PURPOSE UPS 650VA/1200VA/2200VA UPS USER MANUAL F-11 LINE INTERACTIVE UPS GENERAL PURPOSE UPS 650VA/1200VA/2200VA IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for models Aurora Vista

More information

c-go 12V/10A 12V/20A Power supply and battery charger Instruction manual

c-go 12V/10A 12V/20A Power supply and battery charger Instruction manual c-go 12V/10A 12V/20A Power supply and battery charger GB Instruction manual 1 Index 1. Product description... 2 2. Safety advices... 3 3. Mounting and installation... 4 4. Operation... 5 5. Problem solving...

More information

Specifications 2019-V AC-DC Din Rail Mounted Power Supply IS-480 Series, 480W

Specifications 2019-V AC-DC Din Rail Mounted Power Supply IS-480 Series, 480W 2019-V1.0-0118 Specifications AC-DC Din Rail Mounted Power Supply IS-480 Series, 480W No. 545 Museum Road Yangzhou, Jiangsu China 225009 Tel: 86 (514) 8279 1592 Fax: 86 (514) 8769 3159 2019 AC-DC Din Rail

More information

WELDING INVERTER. PEGAS 160 E Smart PEGAS 200 E Smart OPERATING MANUAL. ALFA IN a.s. PEGAS E Smart Manual EN 04

WELDING INVERTER. PEGAS 160 E Smart PEGAS 200 E Smart OPERATING MANUAL. ALFA IN a.s.   PEGAS E Smart Manual EN 04 WELDING INVERTER PEGAS 160 E Smart PEGAS 200 E Smart OPERATING MANUAL PEGAS 160-200 E Smart Manual EN 04 2/12 CONTENT: 1. INTRODUCTION... 3 2. SAFETY INSTRUCTIONS AND WARNINGS... 4 3. TECHNICAL DATA...

More information

CIRCUIT-TEST OPERATION MANUAL. Switching Mode Power Supply with Remote Sensing PSC V 5A / 0-27V 3A / 0-36V 2.2A (80W)

CIRCUIT-TEST OPERATION MANUAL. Switching Mode Power Supply with Remote Sensing PSC V 5A / 0-27V 3A / 0-36V 2.2A (80W) CIRCUIT-TEST Switching Mode Power Supply with Remote Sensing PSC-9800 0-16V 5A / 0-27V 3A / 0-36V 2.2A (80W) OPERATION MANUAL 1 2 PSC-9800 08R14 Contents Safety Precautions...page 4 Introduction... 5 Controls

More information

Pure Sine Wave Inverter GP-HS1500. Owner s Manual

Pure Sine Wave Inverter GP-HS1500. Owner s Manual Pure Sine Wave Inverter GP-HS1500 Owner s Manual 2 Table of Contents Introduction 3 Specifications 4 Name and Main Function 5 Installation 7 Operation 9 Operating Limits 13 Troubleshooting 13 Maintenance

More information

Installation manual portable distributors

Installation manual portable distributors EN Installation manual portable distributors EN 60003206 Issue 11.2016 15/11/2016 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2 Intended

More information

Multi-Mover Charger for model L25

Multi-Mover Charger for model L25 Multi-Mover Charger for model L25 Important safety instruction. Keep these instructions. This manual contains important instructions for the safety of the user and the operation of the device. 1. SYMBOLS

More information

Model 1672, 1673 Triple Output Power Supply

Model 1672, 1673 Triple Output Power Supply Model 1672, 1673 Triple Output Power Supply INSTRUCTION MANUAL 1 Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all phases

More information

Automatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC

Automatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC Automatic Battery Charger Switching mode with Micro-controlled Input:220-260Vac / Output: 12Volt DC User s Manual and Important Safety Information Model: OC-SW121080 / OC-SW121160 / OC-SW121210 FEATURES

More information

Silvertel. Ag Features. 2. Description. Power-Over-Ethernet Module for CCTV. IEEE802.3af compliant

Silvertel. Ag Features. 2. Description. Power-Over-Ethernet Module for CCTV. IEEE802.3af compliant Silvertel V2.4 August 202 Datasheet Pb. Features IEEE802.3af compliant Standard CCTV package sizes - 38mm x 38mm x 6mm (H) or 42mm x 42mm x 6mm (H) Low cost Input voltage range 36V to 57V Input diode bridges

More information

Silvertel. Ag Features. 2 Description. Power-Over-Ethernet Module. IEEE802.3af compliant. Small SIL package size - 56mm (L) x 14mm (H) Low cost

Silvertel. Ag Features. 2 Description. Power-Over-Ethernet Module. IEEE802.3af compliant. Small SIL package size - 56mm (L) x 14mm (H) Low cost Silvertel V2.5 Feb 2014 Datasheet Pb 1 Features IEEE802.3af compliant Small SIL package size - 56mm (L) x 14mm (H) Low cost Input voltage range 36V to 57V Minimal (low cost) external components required

More information

Silvertel. Ag Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W output power

Silvertel. Ag Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W output power Silvertel V1.2 Sept 2014 Datasheet Pb 1 Features IEEE802.3at and IEEE802.3af compliant Maximum 30W output power Dual In-Line (DIL) package size 50.6mm (L) x 30mm (W) Overload, short-circuit and thermal

More information

Phocos CML-V2. Solar charge controller. User Manual (English) Dear customer,

Phocos CML-V2. Solar charge controller. User Manual (English) Dear customer, Phocos CML-V2 Solar charge controller User Manual (English) Dear customer, Thank you very much for buying this Phocos product. Please read the instructions carefully and thoroughly before using the product.

More information

KMP Insulation-Continuity Tester. Users Manual

KMP Insulation-Continuity Tester. Users Manual KMP 7036 Insulation-Continuity Tester Users Manual KMP7036 Insulation-Continuity Tester Users Manual English September 2011, Rev.1 2011 Amprobe Test Tools. All rights reserved. Printed in China Limited

More information

Installation Instructions & Users Manual

Installation Instructions & Users Manual Installation Instructions & Users Manual UTILITY/ BUILDING INPUT 120 VAC ( OPTION) 15-20A N L CONTROL BOARD G SECURITY LIGHTING POWER SUPPLY (OPTION) CHARGER- POWER SUPPLY ASSBY XFMR (OPTION) CBM MODEL

More information

HYGRODYNAMICS DIGITAL DEW POINT MONITOR PC BOARD MODEL 6392N & 6392N2 TABLE OF CONTENTS

HYGRODYNAMICS DIGITAL DEW POINT MONITOR PC BOARD MODEL 6392N & 6392N2 TABLE OF CONTENTS HYGRODYNAMICS DIGITAL DEW POINT MONITOR PC BOARD MODEL 6392N & 6392N2 TABLE OF CONTENTS INTRODUCTION... 2 SPECIFICATIONS... 2 INSTALLATION... 3 PC Board Mounting...3 Sensor Installation...3 Manifold Assembly...4

More information

User Manual Rittal PMC UPS 6kVA

User Manual Rittal PMC UPS 6kVA User Manual Rittal PMC UPS 6kVA Germany Rittal GmbH & Co. KG Auf dem Stützelberg D-35745 Herborn Tel.: ++49-27 72-5 05-0 Fax: ++49-27 72-5 05-23 19 Internet: www.rittal.de 26 Contents 1. Introduction...

More information

DIN-Rail DC UPS. Powers Loads and Charges Back-Up Battery, Ideal for Automation and Wireless System Transmitter Applications

DIN-Rail DC UPS. Powers Loads and Charges Back-Up Battery, Ideal for Automation and Wireless System Transmitter Applications DIN-Rail DC UPS Powers Loads and Charges Back-Up Battery, Ideal for Automation and Wireless System Transmitter Applications Combines all system power functions: power supply, battery charger, UPS circuitry

More information

DIN Rail UPS Model: DIN-UPS 48-5 Installation/Operation Manual

DIN Rail UPS Model: DIN-UPS 48-5 Installation/Operation Manual DI Rail US Model: DI-US 48-5 Installation/Operation Manual Table of Contents Section age Section age Quick Start 2 1) General Information 4 Materials rovided 4 Optional quipment 4 2) Safety Information

More information

model ps600 Address all communications and shipments to: FEDERAL SIGNAL CORPORATION

model ps600 Address all communications and shipments to: FEDERAL SIGNAL CORPORATION MODEL: PS600 HZ: 60 A model ps600 installation and service manual for federal model ps600 FEDERAL SIGNAL CORPORATION POWER SUPPLY VOLTS: SERIES: 120VAC FEDERAL SIGNAL CORPORATION UNIVERSITY PARK, IL. U.S.A.

More information

LESTRONIC II BATTERY CHARGER TAYLOR-DUNN MODEL TYPE 24LC25-8ET

LESTRONIC II BATTERY CHARGER TAYLOR-DUNN MODEL TYPE 24LC25-8ET LESTRONIC II BATTERY CHARGER TAYLOR-DUNN 79-301-10 MODEL 13110-32 TYPE 24LC25-8ET AC Supply: DC Output: Battery Capacity: Specifications 120 volts, 60 Hertz, single-phase 24 volts, 32 amps Use only on

More information

Video & Power Over Coax Kit

Video & Power Over Coax Kit VPoC User Manual Video & Power Over Coax Kit 1CH Video Power over Coax w/ 12V DC Receiver Device VPoC24DC-01K VPoC24DC-01 N-42-1 x1 N-41C 4CH / 8CH / 16CH Video Power over Coax Server Kit VPoC24DC-04K

More information

DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL

DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL 72-7570 DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL Table of Contents Specification 1 Safety 3 EMC 4 Installation 5 Connections 5 Operation 6 Maintenance 8 Specification General specifications

More information

SMP3CTX Series Power Supply/Charger

SMP3CTX Series Power Supply/Charger SMP3CTX Series Power Supply/Charger Installation Guide Models Include: SMP3CTX SMP3PMCTX SMP3PMCTXX - Single Output. SMP3PMP4 - Four (4) Fuse Protected Outputs. SMP3PMP8 - Eight (8) Fuse Protected Outputs.

More information

Silvertel. Ag Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W peak output power

Silvertel. Ag Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W peak output power Silvertel V.3 April 207 Datasheet Pb Features IEEE802.3at and IEEE802.3af compliant Maximum 30W peak output power Small Single In-Line (SIL) package size 57.3mm (L) x 4mm (H) Overload, short-circuit and

More information

INDUSTRIAL POWER SUPPLIES SFL-SERIES

INDUSTRIAL POWER SUPPLIES SFL-SERIES INDUSTRIAL POWER SUPPLIES SFL-SERIES Operating Instructions 1. Application The SFL-series are compact, rugged switching power supplies designed for applications in process automation and other industrial

More information

Triple Output Power Supply

Triple Output Power Supply Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com Model 1672, 1673 Triple Output Power Supply INSTRUCTION MANUAL 1 Safety Summary The following safety precautions

More information

Advanced Battery Charger 0 ~ 15A 0 ~ 25A 0 ~ 35A 0 ~ 50A 0 ~ 80A. 3 - stage charging capability (IUOU) 90 ~ 264VAC (refer to de-rating curve)

Advanced Battery Charger 0 ~ 15A 0 ~ 25A 0 ~ 35A 0 ~ 50A 0 ~ 80A. 3 - stage charging capability (IUOU) 90 ~ 264VAC (refer to de-rating curve) Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.

More information

Power Supply EL

Power Supply EL General information: EL610-2412-24 with dual outputs has been specifically developed to meet the DC powering requirements for telecommunications, industrial and marine applications. The unit has a 230Vac,

More information

ACCUSENSE CHARGE SERIES ON/OFF BOARD FULLY AUTOMATIC BATTERY CHARGER

ACCUSENSE CHARGE SERIES ON/OFF BOARD FULLY AUTOMATIC BATTERY CHARGER ACCUSENSE CHARGE SERIES ON/OFF BOARD FULLY AUTOMATIC BATTERY CHARGER SPECIFICATIONS: *Photo for reference only* Part number 8890439 Mode Select: Selects Battery Type Refer to Section 6. IMPORTANT: READ

More information

99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Instruction Manual. Model 1672 Triple Output Power Supply

99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Instruction Manual. Model 1672 Triple Output Power Supply 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com Instruction Manual Model 1672 Triple Output Power Supply Contents Section Description Page No. CONTENTS 1 1 TEST INSTRUMENT

More information

Sinewave Inverters. SWING 150VA and 300VA. User s manual

Sinewave Inverters. SWING 150VA and 300VA. User s manual Sinewave Inverters SWING 150VA and 300VA User s manual 1 Warranty RIPEnergy is not manufacturer of these units. All technical information s, data s and dimension s rely on information s given by the manufacturer.

More information

Automatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC

Automatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC Automatic Battery Charger Switching mode with Micro-controlled Input:220-260Vac / Output: 12Volt DC User s Manual and Important Safety Information Model: OC-SW121080 / OC-SW121160 / OC-SW121210 FEATURES

More information

SecuriFire. Power Supply Unit B6-PSU. Technical Description. Securiton AG Alpenstrasse Zollikofen Switzerland

SecuriFire. Power Supply Unit B6-PSU. Technical Description. Securiton AG Alpenstrasse Zollikofen Switzerland SecuriFire Power Supply Unit B6-PSU Technical Description Securiton AG Alpenstrasse 20 3052 Zollikofen Switzerland T 811 039 en a Imprint Imprint Notice This document, T 811 039, is valid only for the

More information