Turn OFF all power to the Automatic Door if a Safety System is not working.
|
|
- Ginger Campbell
- 5 years ago
- Views:
Transcription
1 This document is meant to serve as a Quick Set-Up Guide only. Installation manuals referenced below should be downloaded from the NABCO Website and reviewed for complete installation instructions. GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide P/N --00 Rev -- Nabco Entrances Inc. S W Gemini Drive Muskego Wisconsin 0 Phone: () - Fax: () - Associated Manuals Part Numbers: Electrical Installation Manual **with U0 Microprocessor Controller** (Revision D Software) Rev -0- (P/N -0-0) WARNING Turn OFF all power to the Automatic Door if a Safety System is not working. Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO trained technician. Failure to follow these practices may result in serious consequences. NEVER leave a Door operating without all Safety detection systems operational. Table of Contents SECTION : RETROFIT THE BELT CLIP... SECTION : INSTALL THE ELECTRIC LOCK... SECTION : U0 WITH FAIL SAFE OR FAIL SECURE ELECTRIC LOCK... SERVICE PARTS: U-0 ELECTRIC LOCK RETROFIT KIT... of
2 THIS PAGE IS INTENTIONALLY LEFT BLANK
3 GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide Rev -- P/N --00 SECTION : Retrofit the Belt Clip Note: Electric Locks can not prevent Breakout. If preventing Breakout is deemed necessary, panic hardware must be fitted to the Door Panels.. Remove () /-0 x inch Hex Head screws used to secure the Belt Clip to the Belt Bracket. Save the spacers, screws and lock washers for reinstallation. a. Ensure the Belt Clip stays intact with the Belt, so the Belt does not lose Belt Tension.. Remove () /-0 x / inch Hex Head screws used to secure the Belt Bracket to the Carrier. Save screws for reinstallation.. Obtain the Belt Clip Assembly provided within the Electric Lock Retrofit Kit.. Review the Belt Clip Assembly to ensure the secured position will match Figure and Figure. a. If necessary rotate the Latch so the Flat Side of Latch faces the located on the Lock Assembly. DN 0 Flat Side of Latch Flat Side of Latch Figure Proper Latch Orientation. Secure the Belt Bracket to the Belt Clip with () /-0 x inch Hex Head screws, lock washers, and spacers that were saved for reinstallation. Do not overtighten the screws. a. Ensure the Belt Clip is in the correct position (Top vs Bottom) as shown in Figure.. Secure the Belt Bracket to the Carrier with () /-0 x / inch Hex Head screws that were saved for reinstallation. Do not overtighten the screws. Power Supply DS 0 Motor U0 Control Belt Clip Top / SINGLE SLIDE DOOR; LHFS, RHFO / Belt Clip Top Belt Bracket U0 Control DS 0 Motor Power Supply SINGLE SLIDE DOOR; RHFS, LHFO DS0 Motor U0 Control Belt Clip Top Power Supply / Belt Clip Bottom DN 0 BI-PART SLIDE DOOR Belt Bracket Figure Belt Clip Location in Full Close Position of
4 GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide P/N --00 Rev -- SECTION : Install the Electric Lock. Insert () - x / inch T-Bolts into the Channel located inside Header and turn clockwise so they do not fall out. Insert T-Bolt into Channel DN 0 Turn T-Bolt Clockwise to Lock into Channel Figure Insert Socket Head Cap Screws into Channel. Obtain the Electric Lock provided within the Electric Lock Retrofit Kit.. Place the Electric Lock over the () /- x / inch T-Bolts. a. Ensure the is facing the Pivot side of Slide Door.. Loosely secure the Electric Lock to the T-Bolts with () /- Whizlock nuts.. Position the Electric Lock so the Strike is directly behind the Latch when the Slide door is in the Fully Closed Position. Please see Figure. a. Ensure there is a slight gap between the Strike Wall and Flat of Latch. Strike Latch Strike Wall Slight Gap (Between Strike Wall and Flat of Latch in Full Close Posi on) DN 0 Figure. Tighten () /- Whizlock nuts to secure the Electric Lock to the Channel.. Wire the Electric Lock. Please see Section. Ensure is Facing Pivot Side of Slide Door of
5 0 H H A M P GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide Rev -- P/N --00 SECTION : U0 with Fail Safe or Fail Secure Electric Lock Note: Electric Lock only works in One Way mode or Night Mode. HANDY TERMINAL HARNESS P/N - MOTOR/OPERATOR P/N - U0 CONTROL P/N -0-0 POWER SUPPLY P/N - HANDY TERMINAL P No. WARNING 0 T NOISE FILTER MADE IN JAPAN - DS-0 GYRO TECH TB TRANSFORMER ZNR ZNR 0 Microprocessor Controller 0- FUNCTION [SLIDING DOOR] SYMBOL No. VDC+ DCV VDC-(Common) Interior Activation Holding Beam B Reduced Opening Switch Mode Switch (see Mode SW Usage shown left) M0 M Exterior Activation Sequential Activation SQ Breakout Detector BA 0 Sidelite Presence Sensor SLS Contact Output (Class Load only) N/O OUT.A 0V(.Vpeak)max. N/C OUT.B Amax.(0-0V),.Amax.(0-0V) Common OUT.C Auxiliary Output (Open-Collector) OUT VDC-(Common) To protect against risk of fire or electric shock,use only the certified NABCO power supply. MOTOR P Mode SW Usage M0 M MODE Open Open TWO WAY Gnd Open ONE WAY Gnd Gnd HOLD OPEN Open Gnd NIGHT GYRO TECH POWER B RELATED DEVICES P CAUTION BA ERROR Adjustments to the door can only be made with the NABCO Handy Terminal. Do not disassemble the control box. There are no user serviceable parts POWER P INDICATORS 0VAC 0/0Hz >POM< TB To maintain warranty,repairs must be made by authorized NABCO facilities. S ACV ± 0% 0 / 0 Hz POWER SUPPLY HARNESS P/N - 0 VAC BLACK (HOT) WHITE (COMMON) ON/OFF POWER SWITCH AUXILIARY 0 VAC POWER WIRES (THESE WIRES NORMALLY COILED AND TIED UP) GROUND LUG SCREW TO HEADER GROUND HARNESS P/N - FAIL SAFE No. SYMBOL DCV FUNCTION [SLIDING DOOR] 0V BLK WHT RELATED DEVICES - P VDC+ VDC-(COMMON) INTERIOR ACTIVATION HOLDING BEAM B H M0 REDUCED OPENING SWITCH M SQ BA SLS Mode Switch (see Mode SW Usage shown left) GRY VIO GRAY VIOLET Exterior Activation Sequential Activation 0 0 Breakout Detector Sidelite Presence Sensor FAIL SECURE (OUT A) FAIL SAFE (OUT B) OUT.A OUT.B OUT.C N/O N/C Common Contact Output (Class Load only) 0V(.Vpeak)max. Amax.(0-0V),.Amax.(0-0V) OUT Auxiliary Output (Open-Collector) VDC-COMMON TERMINAL ON U0 MAIN HARNESS LABEL ON U0 CONTROL FAIL SECURE LOCK ASSY. P.N WIRING FOR ELECTRIC LOCK ONLY SHOWN P/N - FAIL SAFE LOCK ASSY. P.N OTHER WIRES NOT SHOWN FOR SIMPLICITY U0 ELECTRIC STRIKE OUTPUT SIGNAL HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER =, ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE ON OFF ACTIVATION SIGNAL OUTPUT: 0 = ELECTRIC STRIKE OUTPUT ON SEC OFF OUTPUT SIGNAL OPENING OUTPUT TIMER 0 =(DO NOT USE) =(DO NOT USE) =(DO NOT USE) = ELECTRIC STRIKE FUNCTION FULL OPEN OUTPUT TIMER.0 SEC FULLY CLOSED FULLY CLOSED CLOSING of
6 GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide P/N --00 Rev -- Service Parts: U-0 ELECTRIC LOCK RETROFIT KIT P/N -0-0 Fail Secure P/N -0-0 Fail Safe * Sold in Parts Bag; P/N -0-0 ** Not sold in Retrofit Kit Front Back DN 0 Header Item Part Finish/Sizes/Notes Description - T-BOLT, / - X. LG -0-0 Fail Secure VON DUPRIN FAIL SEC ELE STRIKE SUB ASSY -0-0 Fail Safe VON DUPRIN FAIL SAFE ELE STRIKE SUB ASSY -00- NUT, WHIZLOCK, /-, ZN -0-0 BELT BRACKET, ELECTRIC LOCK ASSEMBLY -0 SPACER, BELT CLIP, - CLIP, BELT / EXTERNAL STAR WASHER HHCS, /-0 X, ZN -00- HHCS,/-0 X / of
Model GT 1175 Electrical Installation Manual **with U30 Microprocessor Controller** (with Revision D Software)
A M P MADE IN JAPAN GYRO TEC 0V MOTOR P POWER B ERROR GYRO TEC To protect against risk of fire or electric shock,use only the certified power supply. Adjustments to the door can only be made with the andy
More informationSection E Fixed Sidelight All Glass. Header Showing U04 to U19 Drive Train Door Panels DS150 and U30 Drive Train...
Section E1 1 Fixed Sidelight All Glass Header Showing U0 to U19 Drive Train................................................... 3- Door Panels........................................................................
More informationSetup and Programming Manual
Microprocessor and Handy Terminal Setup and Programming Manual Versions U04 to U19 for Sliding Door Systems P/N 159000 Rev 7-2-07 The manufacturer, NABCO Entrances, Inc. suggests that this manual be given
More informationTurn OFF all power to the Automatic Door if a Safety System is not working.
This document is meant to serve as a Quick Set-Up Guide only. Installation manuals referenced below should be downloaded and reviewed for complete installation instructions. GT1400 Standard Bi-old and
More informationAutomatic Entrance Systems
ON NIGHT ONE W A Y HOLD OPEN FULL OPEN UCED OPEN 890 Microprocessor Controller Power Connector ( pin) Main Harness Connector ( pin) Motor Connector ( pin) CAUTION Fuse Inside. Adjustments to the door can
More informationSwing Door Operator Wiring and Adjustment Manual ** with Magnum 4A Control*
S82 W18717 Gemini Drive Muskego, Wisconsin 53150 Phone: (877) 622-2694 ax: (888) 679-3319 www.nabcoentrances.com Technical Support: (866) 622-8325 Swing Door Operator Wiring and Adjustment Manual ** with
More informationGyro Tech Swing Door Conversion Unit (C.U.) Hardware Installation and Service Manual
S82 W18717 Gemini Drive PO Box 906 Muskego, WI 53150 Phone: (877) 622-2694 Fax: (888) 679-3319 www.nabcoentrances.com Gyro Tech Swing Door Conversion Unit (C.U.) Hardware Installation and Service Manual
More informationSenior Swing Control Box. Table of Contents
*740100* 740100 2800 Overhead Consealed Series 9500 Surface Applied Series Senior Swing Control Box Installation Instructions important These instructions are presented in step-by-step sequence. It is
More informationTechnical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin
Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin Technical Bulletin NABCO ENTRANCES TECHNICAL BULLETIN S82 W18717 Gemini Drive Muskego,
More informationLCN AUTOMATIC OPERATORS
LCN AUTOMATIC OPERATORS SENIOR 9530 SENIOR 9540 SENIOR 9550 SENIOR 9560 8310 ACCESSORIES LCN ELECTROMECHANICAL POWERED SYSTEMS ELECTROMECHANICAL AUTOMATIC OPERATORS LCN s electromechanical products are
More information2227 Series Vertical Rod Exit Device. Service manual
7 Series Vertical Rod Exit Device Service manual INDEX 7 Vertical Rod Devices Basic Panic Device... 4-5 Basic Fire Device... 6-7 Vertical Rods and Latch Cases... 8-9 Baseplate Assemblies... 0 Center Case
More informationElectro-Mechanical Swing Operator. Table of Contents
*640072* 640072 Electro-Mechanical Swing Operator Models 8230 & 8240 Installation Instructions Table of Contents General...1 Replacement Parts & System Components...1 1 Pre-Installation Site & Product
More informationGT 710. Surface-Mounted, Low Energy, ADA*, Fire-Rated Swing Door Operator PRODUCT FEATURES
GT 710 Surface-Mounted, Low Energy, ADA*, Fire-Rated Swing Door Operator The GT 710 operates in both automatic and manual modes. It features a 2-60 second hold-open range and a push-n-go feature. The GT
More informationINSTALLATION GUIDE For Surface Mounted Applications (Purchased after 08/01/2018)
Low Energy Swing Door Automatic Operator INSTALLATION GUIDE For Surface Mounted Applications (Purchased after 08/01/2018) IMPORTANT READ THIS SECTION BEFORE PROCEEDING WITH INSTALLATION Security Door Controls
More informationElectrical Options Booklet. Table of Contents
*24228413* 24228413 Electrical Options Booklet Table of Contents EL Wiring... EL Troubleshooting... SD/EL 98/99 Cylinder Dogging... SS Wiring... 330, 350, RX-330 and RX-350 Push Bar Trim Mechanical Installation...
More informationPARTS MANUAL 3327A/3527A SERIES EXIT DEVICES JUNE A SHOWN. PM3327A3527A_b VD Copyright 2005 Ingersoll-Rand. All rights reserved.
PARTS MANUAL JUNE 005 A/5A SERIES EXIT DEVICES 5A SHOWN PMA5A_b VD-4050 Copyright 005 Ingersoll-Rand. All rights reserved. INDEX A/5A Fire and Panic Devices Basic Device... 4-5 Vertical Rods and Latches...
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect
More information3327A/3527A Series Exit Device
A/5A Series Exit Device Service manual 5A SHOWN INDE A/5A Fire and Panic Devices Basic Device... Vertical Rods and Latches... LBR Fire Latch Kit... Baseplate Assembly... 4-5 - 9 Variations of the Basic
More informationPARTS MANUAL 33A/35A SERIES RIM EXIT DEVICES JUNE A RIM 35A RIM. PM33A35A_Rim_B VD Copyright 2005 Ingersoll-Rand. All rights reserved.
PARTS MANUAL JUNE 005 A/5A SERIES RIM EXIT DEVICES A RIM 5A RIM PMA5A_Rim_B VD-4049 Copyright 005 Ingersoll-Rand. All rights reserved. INDEX A/5A Rim Panic Devices Basic Device... 4-5 Baseplate Assembly...
More informationPITNEY BOWES FLEXIBLE INK JET TRANSPORT 36 FIT BASE: FIT-36. Parts Manual. (BOM: FIT36rev1.0) FIT-36parts_rev0 1
FLEXIBLE INK JET TRANSPORT 36 FIT BASE: FIT-36 Parts Manual (BOM: FIT36rev1.0) FIT-36parts_rev0 1 VERSION HISTORY The table below summarizes the history of this document as it is published onto the company
More informationUSERS GUIDE LO-21U LOCKOUT RELAY
USERS GUIDE LO-21U LOCKOUT RELAY PRODUCT DESCRIPTION The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with BEA s Bodyguard or DK-12 overhead
More information*ININST.1039* 2390 Touchbar
*ININST.1039* ININST.1039 Concealed Vertical Rod Panic Device 2390 Touchbar Installation Instructions Index Parts List... 2 Before Installation... 5 Installation... 5 RX Device Wiring... 12 EL Device Wiring...
More informationPARTS MANUAL 33/3547A & 33/3549A SERIES EXIT DEVICES OCTOBER /3547A 33/3549A VD Ingersoll Rand Rev.
PARTS MANUAL OCTOBER 0 /5A & /59A SERIES EIT DEVICES /5A /59A VD-05 0 Ingersoll Rand -8--0 90 Rev. 0/_e INDE /5A & /59A Devices Basic Device... -5 Panic Concealed Vertical Rods and Latches... - Fire Concealed
More informationPARTS MANUAL 3327A/3527A SERIES EXIT DEVICES FEBRUARY A SHOWN. PM3327A3527A_d VD Copyright 2013 Ingersoll Rand
PARTS MANUAL FEBRUARY 0 A/5A SERIES EIT DEVICES 5A SHOWN PMA5A_d VD-050 Copyright 0 Ingersoll Rand INDE A/5A Fire and Panic Devices Basic Device... Vertical Rods and Latches... LBR Fire Latch Kit... Baseplate
More information33A/35A Series Rim Exit Device
A/5A Series Rim Exit Device Service manual A RIM 5A RIM INDEX A/5A Rim Panic Devices Basic Device... -5 Baseplate Assembly... Variations of the Basic Device CD (Cylinder Dogging)... HD-EL (Hex Dogging/Electric
More information22 Series Rim Exit Device. Service manual
Series Rim Exit Device Service manual INDEX Rim Devices Basic Panic Device... 4-5 Basic Fire Device... 6-7 Baseplate Assemblies... 8 Center Case Assembly... 9 Variations of the Basic Device RX (Request
More information98/99 Series Rim Exit Devices
98/99 Series Rim Exit Devices Service manual 99 RIM 98 RIM INDEX 98/99 Rim Devices Basic Panic Device... Basic Fire Device... Baseplate Assemblies... Center Case Assembly... Variations of the Basic Device
More informationARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI
II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,
More information*ININST.1002* 1690 Touchbar. Index:
*ININST.1002* ININST.1002 Concealed Vertical Rod Panic Device 1690 Touchbar Installation Instructions Index: : The door prep for the 1690 Hex Bottom Rod is different than for the RL bottom rod. Please
More informationKAWNEER 1686 EL CONCEALED EXIT DEVICE
FEBRUARY, 2012 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl
More informationParts Catalog SLICING MACHINES
Parts Catalog 00N Slicer SLICING MACHINES MODELS: 00N, 0N & 9N -- IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF SLICER. GLOBE FOOD EQUIPMENT COMPANY
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation
More informationINSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN Application: YAMAHA GRIZZLY 660
INSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN 63172 Application: YAMAHA GRIZZLY 660 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More informationCGB CC5 ALUM - Aluminum Box CGB CC5 BLK - Black Steel Box Installation Instructions for 1982 & Up Club Car DS Cargo Boxes
CGB CC5 ALUM - Aluminum Box CGB CC5 BLK - Black Steel Box Installation Instructions for 1982 & Up Club Car DS Cargo Boxes 2000.5 & Up Mounting Shown CAUTION: DO NOT TRANSPORT PASSENGERS IN CARGO BOX. C/2S
More information98/9947, 98/9949, & 98/9950 Series Exit Devices
98/99 98/99, 98/999, & 98/990 Series Exit Devices 98/999 Service manual 98/990 INDE 98/99, 98/999, & 98/990WDC Devices Basic Device... - Panic and Fire Metal Door Concealed Vertical Rods and Latches...
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More information2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond
More informationPARTS MANUAL 98/9947 & 98/9949 SERIES EXIT DEVICES OCTOBER / /9949 VD-GN Ingersoll Rand Rev.
PARTS MANUAL OCTOBER 0 9/99 & 9/999 SERIES EIT DEVICES 9/99 9/999 VD-GN-0 0 Ingersoll Rand ---0 99 Rev. 0/_f INDE 9/99 & 9/999 Devices Basic Device... - Panic and Fire Metal Door Concealed Vertical Rods
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
More informationClutch Installation Case IH 1200 row unit
Ag Leader Technology SeedCommand NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity 4 row clutch installation kit Case IH 1200 Model year
More informationESA II. I - Revive Slider Conversion Kit. Installation instructions
ESA II I - Revive Slider Conversion Kit Installation instructions DL058-00 05-0 EN dormakaba ESA II I-Revive Slider Conversion Kit Table of Contents Table of contents Table of contents General information
More informationInstallation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 9986 & 9996 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown
More informationPARTS MANUAL 98/9927 SERIES EXIT DEVICES MAY 2013 PM989927_G VD-GN Copyright 2013 Ingersoll Rand
PARTS MANUAL MAY 0 9/99 SERIES EIT DEVICES VD-GN- Copyright 0 Ingersoll Rand INDE 9/99 Devices Basic Panic Device... Basic Fire Device... Vertical Rods and Latches... Baseplate Assemblies... Center Case
More informationSubmersible Pumps Models: ST-2037 ST-2047 ST-2047B ST-2038P ST-2040T
OPERATION AND PARTS MANUAL Submersible Pumps Models: ST-2037 ST-2047 ST-2047B ST-2038P ST-2040T Revision # 1 (11/07/05) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES. ST-2037, 47, 47B, 38P, 40T
More informationSW10 (Full Power) & SW19 (Low Energy)
TUCKER AUTO-MATION SW10 (Full Power) & SW19 (Low Energy) INSTALLATION GUIDE Surface Mounted Applications (See APPENDIX for special notes regarding installation on fire rated doors) PLEASE NOTE: NEW 35mm
More informationPARTS LIST. Toll Free Phone, (US & Canada): (800) Toll Free Fax, (US & Canada): (800)
1/2 SIZE CONVECTION TJ CINNAMON MCO-E-5 PARTS LIST Toll Free Phone, (US & Canada): (800) 427-6668 Toll Free Fax, (US & Canada): (800) 361-7745 http://www.garland-group.com TJ Cinnamon Oven (Rev 01) Page
More informationPARTS MANUAL 98/99 SERIES RIM EXIT DEVICES. May RIM 98 RIM PM9899_G VD-GN Copyright 2013 Ingersoll Rand
PARTS MANUAL May 0 9/99 SERIES RIM EXIT DEVICES 99 RIM 9 RIM PM999_G VD-GN-09 Copyright 0 Ingersoll Rand INDEX 9/99 Rim Devices Basic Panic Device... Basic Fire Device... Baseplate Assemblies... Center
More informationIMI vibration switch USER MANUAL INSTALLATION - OPERATION - MAINTENANCE
USER MANUAL IMI vibration switch INSTALLATION - OPERATION - MAINTENANCE Z0929039_A ISSUED 03/2017 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. contents Overview General
More informationAutomatic Sliding Door Retrofit Drive Assembly. Installation Manual DoorControlsUSA.com
Automatic Sliding Door Retrofit Drive Assembly Installation Manual 800-437-3667 DoorControlsUSA.com TABLE OF CONTENTS pg. 1. COMPONENTS 2 2. HEADER PREPARATION 2 3. DOOR PREPARATION 2 4. MOTOR AND CONTROLLER
More information*70954* 240V Senior Swing Control Box Installation Instructions CAUTION WARNINGS. Table of Contents
*70954* 70954 2800 Overhead Concealed eries 9500 urface Applied eries 240V enior wing Control Box Installation Instructions CAUTION These instructions are presented in step-by-step sequence. It is very
More information6100 Series Swing Door Operator Installation Instructions
6100 Series Swing Door Operator Installation Instructions The manufacturer s specifications for this product require the installation to be approved by an AAADM certified inspector. -USA 4324 Phil Hargett
More informationA CAB KIT (Shown with GLASS DOORS KIT A-11859)
Cab Installation Instructions for John Deere One Series, 1023E, 1025R and 1026R Model Series A-11976 CAB KIT (Shown with GLASS DOORS KIT A-11859) FOR USE WITH OPTIONAL KITS; A-11859 GLASS DOORS WITH NON-OPENABLE
More informationElectrohydraulic Powered Systems
Electrohydraulic Powered Systems ELECTRIC AUTO EQUALIZERS These Auto Equalizer products are an addition to the original pneumatic drive system. People moving through a door can use it as a normal rack
More information*24213* 4040-SE Sentronic. 1 Voltage. 6 Adjusting Hold-Open Door Position. 7 Regulation. 2 Tracking. 8 Door Closer Cover.
*223* 223 00-SE Sentronic Installation Instructions This closer features two mounting options. Before beginning, determine which type of mounting best applies to your application, or had been specified
More informationCLUB SERIES HIP AB/ADDUCTOR
CLUB SERIES HIP AB/ADDUCTOR ASSEMBLY INSTRUCTIONS Part # 718601 Rev E 1 Revision: 1/2/03 KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QT Y 1 71710xx TOWER 1 22 3102915 3/8 X 3-1/ BOLT 2 1A 6692601
More informationInstallation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA
Installation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA1812510 Background: Early production Martin Yale Model 1812 Folders were originally equipped with a spring-clutch type feed
More informationI-BFV.KIT Butterfly Valve Gear Operator Replacement
SERIES 5, 05,, and 0C WARNING Read and understand all instructions before attempting to install, remove, adjust, or maintain any Victaulic piping products. Depressurize and drain the piping system before
More informationCE Certified Master Full Size Gas Convection Oven
CE Certified Master Full Size Gas Convection Oven models MCO-GS/GD-0/0CE from serial# 07000000 (0-JULY-) P (US & Canada): 800 7 8 F (US & Canada): 800 77 www.garland-group.com G_GO_PL_CONVECTION_MCOGSGD0CE
More informationB-PC20 Power Close Module
B-PC20 Power Close Module Instruction Manual Document number: B-PC20-C Release: V1.2 Date: OCT 12,2011 ! WARNING This control must be adjusted/serviced by a qualified person. The service technician must
More informationAt-FST Series I N S TA L L AT I O N A N D O P E R AT I N G I N S T R U C T I O N S W W W. A I G I S M E C H. C O M
FULL HEIGHT GALVANIZED STEEL TURNSTILE SINGLE UNIT 3 60 At-FST Series AT-FST SERIES I N S TA L L AT I O N A N D O P E R AT I N G I N S T R U C T I O N S W W W. A I G I S M E C H. C O M SAFETY PRECAUTIONS
More informationHustler X-ONE i Parts Manual
Hustler X-ONE i Parts Manual 00 South Ridge Road Hesston, Kansas 6706 Table of Contents General Information Service Literature...................................... - Options Available From Your Dealer........................
More informationINSTALLATION INSTRUCTIONS CRL ESK2/ESP2
INSTALLATION INSTRUCTIONS CRL ESK2/ESP2 ELECTRIC STRIKE KEEPER FOR DOUBLE DOORS NOTE: Sensor feature available on ESP s only. ALUMINUM Phone: (800) 421-6144 Fax: (800) 587-7501 crlaurence.com usalum.com
More informationB100S - Super Swing. Instruction Manual. Document number: B100S-C Release: V4.0 Date: May 08,2009
B00S - Super Swing Instruction Manual Document number: B00S-C Release: V4.0 Date: May 08,009 ! WARNING This control must be adjusted/serviced by a qualified person. The service technician must be familiar
More informationMaintenance. Instructions for Ordering. XP Bi-Part, Manual & Power
Instructions for Ordering Maintenance This parts manual is intended to assist in the correct identification of the more commonly replaced parts; covering, generally, all BI- PART models and styles offered
More informationClassic12 Belt Sander
Classic12 Belt Sander Section II Parts and Service Manual AMERICAN SANDERS TECHNOLOGY Classic 12 Belt Sander Operator's Manual Page 21 Assembly Drawing #1 11/00 7 8 9 12 13 11 1 10 85 14 6 81 80 79 76
More information*29268* 4600CS Electronic Low Energy Operator 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT. Table of Contents. Customer Service
*29268* 29268 4630CS, 4640CS Electric Auto Equalizer Series 4600CS Electronic Low Energy Operator Installation Instructions 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT The 4600CS Series electric Auto-Equalizer
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationCHAPTER S e t u p NOTICE:
CHAPTER Setup NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More information5600 Series Power Operator Installation and Instruction Manual
5600 Series Power Operator Installation and Instruction Manual 80-956-000-00 (08-) 5 ASSA ABLOY 6 Item No. Description Motor (5600M) Cover (5600COV) Control Inverter (5600IN) Power Supply VDC (5600PS)
More informationDigitrip Retrofit System for the ITE LG-3000 (Frameless) Circuit Breaker
IL 33-LGH-1 Digitrip Retrofit System for the ITE LG-3000 (Frameless) Circuit Breaker SAFETY PRECAUTIONS WARNING POWER CIRCUIT BREAKERS ARE EQUIPPED WITH HIGH SPEED, HIGH ENERGY OPERATING MECHANISMS. THE
More informationINSTALLATION INSTRUCTIONS
PART NO. 23100T PRODUCT DESCRIPTION: Front Winch Bumper, Center Section PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE PERSONAL
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions
More informationINSTALLATION INSTRUCTIONS
Series 2001 Belt Drive Slide Door & RapidSlide INSTALLATION INSTRUCTIONS To be used with H202 C2150 Ver.2 Control Setup Instructions G2001, FEB 2004 CONTENTS 1. Instructions to installer... G2001.1 2.
More informationPRODUCT LABEL. ID Tag: XP 2000 Manual. When ordering parts, have your ASI job number and door number available.
Door Identification Determining the Job Number, Model and Year of Manufacture of your door is necessary to provide quick and accurate parts identification. Each door has a label showing job number, model
More informationSection H4 GT350 OHC, Magnum 2, 3 & 4 Control, Single. Header Pivots Operator Control Board...13
Section H GT50 OHC,, Header............................................................................ -5 Pivots.............................................................................. - Operator...........................................................................
More informationMK IV OVERHEAD DOOR REPLACEMENT PARTS BOOK
MK IV OVERHEAD DOOR REPLACEMENT PARTS BOOK JAMISON DOOR COMPANY P.O. BOX 70 HAGERSTOWN, MARYLAND 21740 1-800-532-3667 301-733-3100 INTERNET: http://www.jamisondoor.com E-MAIL: contact@jamisondoor.com ECN
More informationSHIVVERS ROTATION DETECTOR. fshiwersf ROTATION DETECTOR 676A-001A
SHIVVERS ROTATION DETECTOR 676A-1A INSTALLATION & OPERATING INSTRUCTIONS fshiwersf ROTATION DETECTOR 676A-1A INDICATOR LIGHT Solid Red = Rotation Is OK Slow Flash (1 sec. on; 1 sec. off)= Rotation Detector
More informationESA-400 Fine Frame. Installation Instructions. 1 Rev. 8/06. Toll-Free: Lake Bluff, IL 60044
Interior View 0 Installation Instructions 1 Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring #2 Phillips (Crosspoint) - for various #8, #10, and #14 screws Wrenches
More informationSL200 Series Scale Link Installation Manual
TM SL200 Series Scale Link Installation Manual Ft. Atkinson, Wisconsin USA Panningen, The Netherlands www.digi-star.com D3934-US Rev A March 29, 2012 Introduction INTRODUCTION Thank you for purchasing
More informationInstallation manual. Pole-mount Deployment System
Installation manual Pole-mount Deployment System 974-80207001/2.0 Pole-mount Deployment System Installation Manual Document revisions Version Date Written by Checked by Approved by 1.0 Aug 25, 2011 BC
More informationPITNEY BOWES FLEXIBLE INK JET TRANSPORT 56 FIT BASE: FIT-56. Parts Manual. (BOM: FIT-56revA) FIT-56parts_rev0 1
FLEXIBLE INK JET TRANSPORT 56 FIT BASE: FIT-56 Parts Manual (BOM: FIT-56revA) FIT-56parts_rev0 1 VERSION HISTORY The table below summarizes the history of this document as it is published onto the company
More informationSERIES 1100 ULTRA GLIDE SLIDER ( with ZII Control )
1100 SERIES SLIDING DOOR INSTALLATION INSTRUICTIONS AND TROUBLESHOOTING GUIDE SERIES 1100 ULTRA GLIDE SLIDER ( with ZII Control ) SERIES 1100 PAGE 1. PRODUCT INFORMATION The KM Systems 1100 slider has
More informationedrive VSi Installation Guide
edrive VSi Installation Guide Kit: EDVSi-AGCO SWATHER, P/N 911-1001-000 Fits Challenger, Hesston and Massey Ferguson Swather Models: SP115B 8250 9260 * (see serial #) 9330 SP185B 8450 8250S 9340 9225 8550S
More information6900 Series PowerMatic Low Energy Power Operator
6900 Series PowerMatic Low Energy Power Operator INTRODUCTION Norton's 6900 Series PowerMatic is a low energy power door operator designed to automatically open and close doors with a lower energy opening
More information6900 Series PowerMatic. Low Energy Power Operator
6900 Series PowerMatic Low Energy Power Operator INTRODUCTION Norton's 6900 Series PowerMatic is a low energy power door operator designed to automatically open and close doors with a lower energy opening
More informationINSTALL INSTRUCTIONS C-VS-2000-TAH-2
INSTALL INSTRUCTIONS C-VS-2000-TAH-2 2015-2019 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (12.5 inches wide) 20 inches of Equipment mounting space Tools Required: Phillips Screw
More informationInstallation & Operation Manual
Installation & Operation Manual This IOM is for the following ProMation Engineering Products: P4-2N4-AC P4-2N4-DC P4-24N4-AC P4-24N4-DC P5-2N4-AC P5-2N4-DC P5-24N4-AC P5-24N4-DC P6-2N4-AC P6-2N4-DC P6-24N4-AC
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationEX40 16ST, EX40 18LX. Parts List Models: (EX40 16ST), (EX40 18LX) Form No /2015 revised 1/2018 REV F
EX40 16ST, EX40 18LX Parts List Models: 56265504 (EX40 16ST), 56265505 (EX40 18LX) Form No. 56042643 7/2015 revised 1/2018 REV F revised 6/2017 PARTS LIST TABLE OF CONTENTS DESCRIPTION PAGE Base System...
More informationMK IV HORIZONTAL SLIDING DOOR REPLACEMENT PARTS BOOK
MK IV HORIZONTAL SLIDING DOOR REPLACEMENT PARTS BOOK BI-PARTING DOOR SHOWN-SINGLE DOOR SIMILAR JAMISON DOOR COMPANY P.O. BOX 70 HAGERSTOWN, MARYLAND 21740 1-800-532-3667 301-733-3100 INTERNET: http://www.jamisondoor.com
More informationPower Operated Retrofit Kit for Manual Door 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual
Therm-L-Tec Building Systems LLC Therm-L-Tech Power Operated Retrofit Kit for Manual Door 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual Rev. A 10/2014 Index Index 1 Electrical Requirements
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More information* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION
*921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications
More information2904 Power Supply Installation Instructions I-EA00041
FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and
More informationCM Lodestar Electric Chain Hoist Electrical Parts List
CM Lodestar Electric Chain Hoist Electrical Parts List MODELS Key No. Part Name No. Req'd A, A-2, AA, AA-2, B, B-2 C, C-2, E, E-2, F, F- 2, H & H-2 J, J-2, JJ, JJ-2, L, L-2, LL, LL-2, R, R- 2, RR, RR-2,
More informationII E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
II E1500-11 INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT KITS ARE UL LISTED UNDER CATEGORY GWVW, GWVW7 (CANADA) (ACCESSORY FOR USE ON FIRE EXIT HARDWARE AND PANIC HARDWARE). INDEX
More informationEco-Propel TM Variable Speed Pump Kit Instruction and Operation Manual, p/n Revision 0
Eco-Propel TM Variable Speed Pump Kit Instruction and Operation Manual, p/n 107065-01 Revision 0 May 20, 2016 Contents Introduction 2 Installation Pre-installation 3 Installation Procedure 4 Electrical
More informationVM-GIB High Torque Actuator (Non-Spring Return) 3-point floating (193B1790) / Modulating (193B1791)
Installation Guide VM-GIB High Torque Actuator (Non-Spring Return) 3-point floating (193B1790) / Modulating (193B1791) VICPA222 Technical Data Power 24 Vac ±20%, 50/60 Hz Power consumption 8 VA (running)
More informationClutch Control. PN: November 2013 Rev E 1
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Module Kit 4100533 1 Cable Installation Kit 2000901-1 1 Alcohol swab packet 2002811 2
More information