Special Tool Required: MPCS Service Connector 07WAZ A
|
|
- Susan Powell
- 5 years ago
- Views:
Transcription
1 Special Tool Required: MPCS Service Connector 07WAZ A 1. Check the No.9 and 13 passenger fuses. Are the fuses OK? YES -Go to step 2. NO -Find and repair the cause of the blown fuse. 2. Test power and ground inputs to all three multiplex control units. 3. Check self-diagnosis function Mode 1 for a diagnostic trouble code (DTC) by connecting the special tool to the multiplex control inspection connector (A). After about 5 seconds, the ignition key light should come on and the beeper should beep for 2 seconds, then go off for 0.2 seconds, then blink and beep for 0.2 seconds. This means that you are in Mode 1 of the self-diagnosis function. 4. Turn the ignition switch ON (II). Does the ignition key light blink and the beeper beep? YES -There is a DTC. Count the blinks/beeps, then go to step 7. NO -See if the SCS circuit is working properly. Go to step Check for continuity between the No.3 terminal of the inspection connector and the A15 terminal in the driver's unit. Is there continuity? YES -Go to step 6. NO -Repair the open in the wire, and recheck for DTCs. 6. Check for continuity between the No.1 terminal of the inspection connector and body ground. Is there continuity? YES -Go to step 13. NO -Repair the open in the wire, and recheck for DTCs.
2 7. One second after you go into self-diagnosis mode 1, the ignition key light and beeper indicate the DTC, and repeat it every 3 seconds. If there is more than one DTC, the system will indicate them in ascending order, beginning from the DTC with the lowest numerical value. Find your DTC in this table, then go to step 8 and check the communication lines. 8. With the ignition switch OFF, check for continuity according to the table. Is there continuity? YES -Go to step 9. NO -Check for an open in the wire. 9. Turn the ignition switch ON (II), and check for voltage between the communication line and ground. Does the voltage match the table? YES -Communication lines are OK. Go to step 10. NO - Repair the line according to the following. If the voltage is too high: Check for a short to another wire. Check for poor contact in the connector at the receiving unit. If the voltage is too low: Check for a short to ground or to another wire. Check for poor contact at the connector on the transmitting unit. Faulty circuit in the transmitting unit.
3 10. Shift to the sleep mode: Turn the ignition switch OFF. Cancel the key-off operation timer in the power window system by opening and closing one of the doors. Make sure that the exterior lights are off. If you do not operate any switches related to the multiplex control units within one minute after meeting the above conditions, the system function shifts to the sleep mode. (All of the switches must be turned OFF except door lock knob switches). 11. Confirm the sleep mode: Check for voltage in the BRN and PNK lines between control units. These should be approximately 12 volts in the sleep mode. Check for voltage between each communication line and body ground while shifting to the sleep mode. There should be no voltage. Check the parasitic draw at the battery while shifting to the sleep mode. Amperage should change from about 70 through 80 ma to less than 10 ma. 12. Confirm the wake up mode. When the ignition switch in turns ON (II), all of the multiplex control units wake up at the same time without "talking" to each other through the communication lines. When any switch in the multiplex system is turned on, it wakes up its related control unit which, in turn, wakes up the other units. After confirming the sleep mode, look in the following tables for the switch most closely related to the problem. Operate that switch and see if its control unit wakes up. NOTE: If any control unit is faulty and will not wake up, several pants of the system will malfunction at the same time.
4 In each table, the control unit is followed by a list of the switches and input signals that can wake it up. Is the wake-up function OK? YES -Troubleshoot the individual system function that had a problem. NO -Repair the open or short in the communication line(s). 13. From Mode 1, disconnect the special tool from the multiplex control inspection connector for about ten seconds, then reconnect it. The ignition key light should
5 come on and the beeper should beep for 2 seconds, then blink and beep twice more at 0.2 second intervals. This means the system has gone from Mode 1 to Mode 2. Mode 2: NOTE: To cancel mode 2, disconnect the SCS service connector from the multiplex control inspection connector for more than 10 seconds or turn the ignition switch OFF. 14. Look in the following tables for the switch most closely related to the problem. While still in Mode 2, operate that switch to test the circuit between the switch and its control unit. If the circuit is OK, the ignition key light should blink once and the beeper should beep once. If the circuit is faulty, there will be no indication. Does the ignition key light blink and beeper beep? YES -The circuit is OK. Refer to the test(s) for that individual system. NO -Go to step 15.
6 In each table, the control unit is followed by a list of circuits that it can check in Mode Check two or three more circuits listed for that control unit. Does the ignition key light blink and the beeper beep for each circuit? YES -The additional circuits are OK. Repair the short or open in the circuit that failed the test in the preceding step. NO -Multiple failed circuits can mean that the control unit has failed, but without triggering a DTC. Test a few more circuits. If they also fail, substitute a knowngood control unit, then recheck. If the system works properly, the original control unit is faulty; replace it. If there is a still a malfunction, substitute a known-good control unit for the next most likely faulty control unit, then recheck. If the system works properly, that control unit is faulty; replace it.
COMPONENT LOCATION INDEX
COMPONENT LOCATION INDEX 2003-04 ACCESSORIES & EQUIPMENT Gauges - Element Fig. 1: Identifying Gauges Component Locations Page 1 Fig. 2: Locating Gauges & Gauge Connectors & Identifying Gauge Connector
More information1995 Honda Accord LX. ANTI-LOCK BRAKE SYSTEM' ' BRAKES Honda - Anti-Lock
TROUBLE SHOOTING ANTI-LOCK (ABS) WARNING LIGHT NOTE: ABS system is okay if ABS warning light goes out after engine is started. Diagnostic Trouble Code (DTC) Recognition 1. ABS control unit recognizes system
More information2003 PILOT - Power Window Multiplex Control Unit Input Test
2003 PILOT - Power Window Multiplex Control Unit Input Test Passenger's Unit 1. Before testing the power window control functions, troubleshoot the multiplex control system. 2. Remove the passenger's multiplex
More informationTL - Keyless Entry/Security Alarm System Control Unit Input Test
1999 3.2TL - Keyless Entry/Security Alarm System Control Unit Input Test '99-01 Models 1. Before testing the keyless entry/security control functions, troubleshoot the multiplex control system. Multiplex
More information2005 Honda Civic DX. Information marked with an asterisk (*) applies to the D17A2 engine.
DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION NOTE: Information marked with an asterisk (*) applies to the D17A2 engine. 1. Reset the ECM/PCM (see HOW TO RESET THE ECM/PCM ). 2. Start the
More informationPGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING
PGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING 1. Turn the ignition switch OFF, then disconnect the PGM-FI main relay 7P connector. 2. Check for continuity between body ground and PGM-FI main relay 7P connector
More informationIf the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
POWER WINDOW MULTIPLEX CONTRO... 2003 ODYSSEY Power Window Multiplex Control Unit Input Test 1. Before testing the power window control functions, troubleshoot the multiplex control system. Driver's Multiplex
More informationBefore performing symptom troubleshooting, check for power train DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
2003 Honda Civic 1.7L Eng LX Component AC PRESSURE SENSOR A/C Pressure Switch Circuit Troubleshooting NOTE: Do not use this troubleshooting procedure if any of the following items are operative; condenser
More informationRS 44 SUPPLEMENTAL RESTRAINT SYSTEM HINT:
RS44 DIAGNOSIS INSPECTION SRS warning light check (a) Turn the ignition switch to ACC or ON and check that the SRS warning light lights up. (b) Check that the SRS warning light goes out after approx. 6
More information2004 Honda Element EX DTC P2647: ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE
DTC P2647: ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting
More informationTIRE PRESSURE AND MONITORING SYSTEMS (DIAGNOSTICS)
TIRE PRESSURE AND MONITORING SYSTEMS (DIAGNOSTICS) Basic Diagnostic Procedure 1. Basic Diagnostic Procedure A: PROCEDURE CAUTION: Remove foreign matter (dust, water, oil etc.) from the tire pressure monitoring
More information2001 Honda Accord DX DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION, DTC P0141: SECONDARY HO2S (SENSOR 2) HEATER CIRCUIT MALFUNCTION
DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION, DTC P0141: SECONDARY HO2S (SENSOR 2) HEATER CIRCUIT MALFUNCTION NOTE: Information marked with an asterisk (*) applies to DTC P0141. 1. Reset
More informationDTC P1655 Evaporative Emission (EVAP) Purge Solenoid Control Circuit
Page 1 of 5 1997 Pontiac Grand Am Achieva, Grand Am, Skylark (VIN N) Service Manual Document ID: 58460 DTC P55 Evaporative Emission (EVAP) Purge Solenoid Control Circuit Circuit Description Output Driver
More informationBODY ELECTRICAL SYSTEM
BODY ELECTRICAL SYSTEM 8-1 SECTION 8 BODY ELECTRICAL SYSTEM WARNING: For vehicles equipped with Supplemental Restraint (Air Bag) System: Service on and around the air bag system components or wiring must
More informationThe VTM-4 indicator comes on under certain conditions even if the 4WD system is working normally. Here are some examples:
2012 Pilot VTM-4 Indicator Report a problem with this article The VTM-4 indicator comes on under certain conditions even if the 4WD system is working normally. Here are some examples: When you use high-powered
More informationCONTENTS MOTORCYCLE. ISSUE NO.: M DATE: Oct. 19, 2004 PAGE: 1 OF 9
MOTORCYCLE ISSUE NO.: M-4-0319 DATE: Oct. 19, 2004 PAGE: 1 OF 9 SUBJECT: CORRECTION AND ADDITIONAL INFORMATION OF THE SERVICE MANUAL APPLICABLE MODEL: LT-A700XK5 EFFECTIVE ENGINE OR FRAME NO.: REFERENCE:
More informationSTARTER CIRCUIT TROUBLESHOOTING
2000 Honda Accord EX Sedan V6-3.0L Vehicle > Starting and Charging > Starting System > Starter Motor > Testing and Inspection > Component Tests and General Diagnostics STARTER CIRCUIT TROUBLESHOOTING Starter
More informationComponent Description
Component Description Component Description IGNITION COIL & POWER TRANSISTOR NFEC0286 NFEC0286S01 The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor
More information2006 TL - Driving Position Memory Switch Test/Replacement
2006 TL - Driving Position Memory Switch Test/Replacement 1. Remove the driver's door panel. 2. Disconnect the 10P connector from the memory switch (A). A 3. Check for continuity between the terminals
More information11.Airbag Warning Light Failure
11.Airbag Warning Light Failure A: AIRBAG WARNING LIGHT REMAINS ON. DIAGNOSIS: Airbag warning light unit is faulty. Airbag control module to airbag warning light circuit is shorted or open. Grounding circuit
More informationPower Sliding Door (PSD) Diagnostic Approach. Fixing Intermittent Malfunctions. Power Sliding Door (PSD) Diagnostic Information
Power Sliding Door (PSD) Diagnostic Information Power Sliding Door (PSD) The power sliding door (PSD) provides built-in diagnostics. This assists the service technicians during troubleshooting. The PSD
More informationON BOARD DIAGNOSTIC SYSTEM DESCRIPTION Self-diagnosis. Self-diagnosis BR-44 FUNCTION SELF-DIAGNOSIS PROCEDURE ABS
Self-diagnosis ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION Self-diagnosis FUNCTION NABR0095 NABR0095S01 When a problem occurs in the, the warning lamp on the instrument panel comes on. To start the self-diagnostic
More information2004 TSX - How to Troubleshoot the Climate Control System
2004 TSX - How to Troubleshoot the Climate Control System How to Check for DTCs with the HDS 1. Make sure the ignition switch is OFF. 2. Connect the HDS to the data link connector (DLC) (A) located under
More informationDI-377 SUPPLEMENTAL RESTRAINT SYSTEM DI58G-01 PRE-CHECK
W01632 PRECHECK DI377 DI58G01 1. SRS WARNING LIGHT CHECK (a) Turn the ignition switch to the ACC or ON position and check that the SRS warning light lights up. (b) Check that the SRS warning light goes
More information2001 CIVIC - Immobilizer System Troubleshooting
Page 1 of 5 2001 CIVIC - Immobilizer System Troubleshooting 1. Turn the ignition switch ON (II) with a programmed key. 2. Check to see if the immobilizer indicator comes on. Does the indicator come on?
More information2005 ODYSSEY - Front Door Panel Removal/Installation
2005 ODYSSEY - Front Door Panel Removal/Installation Special Tools Required KTC trim tool set SOJATP2014 Trim pad remover, Snap-on A 177A or equivalent, commercially available NOTE: Use the appropriate
More informationTechnical Bulletin AA 304. Central Locking System. m.y. 97
Technical Bulletin Subject: Model(s): Central Locking System Cabriolet m.y. 97 Group: Number: Date: 01 96 11 Nov. 29, 1996 The following Repair Manual pages are new and will be integrated with the next
More informationDIAGNOSTIC TROUBLE CODE CHART
18 Cruise Control System DIAGNOSTIC TROUBLE CODE CHART If a trouble code is indicated while checking DTCs, inspect the listed for that code in the table below, and proceed to the applicable page. DTC No.
More informationA/T INTERLOCK SYSTEM Acura TSX AUTOMATIC TRANSMISSIONS A/T Interlock System - TSX COMPONENT LOCATION INDEX
A/T INTERLOCK SYSTEM COMPONENT LOCATION INDEX 2004 AUTOMATIC TRANSMISSIONS A/T Interlock System - TSX Fig. 1: Locating A/T Interlock System Components CIRCUIT DIAGRAM Wednesday, March 12, 2008 9:52:31
More informationHow to Retrieve a DTC (Without HDS)
How to Retrieve a DTC (Without HDS) The climate control unit has a self-diagnostic function. To run the self-diagnostic function, do the following: NOTE: Before troubleshooting the climate control system,
More informationIndividual ignition coil system,
Page 1 of 11 28-17 Individual ignition coil system, checking Ignition coils, checking Notes: Measuring the primary resistance of the ignition coils is normally not necessary for this test (primary resistance
More informationVolkswagen B3 Passat Diagnosis, Fault Memory - Passat Diagnosis, Fault Memory (Page GR-D4)
Diagnosis, Fault Memory (Page GR-D4) Anti-lock brake system (ABS) electrical testing self-diagnosis troubleshooting using electrical steps VAG 1551 Diagnostic Tester connecting erasing Fault memory reading
More informationPRE CHECK 1. SRS WARNING LIGHT CHECK
H08442 PRECHECK DI287 DI4L104 1. SRS WARNING LIGHT CHECK (a) Turn the ignition switch to the ACC or ON position and check that the SRS warning light lights up. (b) Check that the SRS warning light goes
More information09 03 SYMPTOM TROUBLESHOOTING
SYMPTOM TROUBLESHOOTING KEYLESS ENTRY SYSTEM WIRING DIAGRAM................ 1 FOREWORD...................... 1 KEYLESS ENTRY SYSTEM CHECK SHEET................... 2 KEYLESS ENTRY SYSTEM PREINSPECTION.................
More informationSECURITY CONTROL SYSTEM
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY SECTION SEC A SECURITY CONTROL SYSTEM B C D CONTENTS E BASIC INSPECTION... 3 DIAGNOSIS AND REPAIR WORKFLOW... 3 Work Flow...3 INSPECTION AND ADJUSTMENT...
More informationDocument ID# Chevrolet Chevy Suburban - 4WD
Page 1 of 8 Document ID# 757392 2003 Chevrolet Chevy Suburban - 4WD Print DTC C0455 Circuit Description The steering wheel position sensor (SWPS) provides one analog signal and 3 digital
More informationPower Supply Circuit For Transfer Control Unit
Page 1 of 7 2005 Nissan Xterra 4.0L Eng S Power Supply Circuit For Transfer Control Unit CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE Data are reference value. DATA MONITOR MODE REFERENCE Monitored
More informationCVT RE0F09B TCM P1701 TCM. Description
2012 Nissan-Datsun Altima L4-2.5L (QR25DE) Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P1701 CVT RE0F09B TCM P1701 TCM Description When the power supply to
More informationActive Grille Air Shutter 1 Malfunction
Page 1 of 5 Active Grille Air Shutter 1 Malfunction 2015 Cadillac ATS 2.0L Eng Premium Print Date: Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
More informationAUTOMATIC AIR CONDITIONER > COMPONENT DIAGNOSIS > BLOWER MOTOR CONTROL SYSTEM > SYSTEM DESCRIPTION > SYSTEM DESCRIPTION
2008 Nissan Armada 5.6L Eng SE HEATER & AIR CONDITIONING CONTROL SYSTEM MOTOR CONTROL SYSTEM > SYSTEM DESCRIPTION > SYSTEM DESCRIPTION Component Parts Blower speed control system components are: A/C auto
More informationDocument ID: General Motors Corporation. All rights reserved.
Page 1 of 6 2005 Chevrolet TrailBlazer - 4WD Envoy, Rainier, TrailBlazer, Ascender (VIN S/T) Service Manual Document ID: 1489377 DTC P0053 or P0054 Circuit Description The heated oxygen sensor (HO2S) must
More informationCOMPONENT LOCATION INDEX
DTC TROUBLESHOOTING COMPONENT LOCATION INDEX 2007-08 ENGINE PERFORMANCE Idle Control System - Element Fig. 1: Identifying Idle Control System Component Location DTC P0506: IDLE CONTROL SYSTEM RPM LOWER
More information1999 Toyota RAV ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4
1999 ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4 DESCRIPTION WARNING: Deactivate air bag system before performing any service operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT apply electrical
More informationCAUTION: Ensure battery Is fully charged prior to testing. Low battery voltage will cause faulty diagnostic system operation.
AUTO TRANS DIAGNOSIS - A-340E/F/H & A-341E Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information
More informationDTC P1351 Ignition Coil Control Circuit High Voltage
Page 1 of 5 1996 Chevrolet Chevy K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Document ID: 34079 DTC P1351 Ignition Coil Control Circuit High Voltage Circuit
More informationPRE CHECK DI 211 2WD: DLC3 CG F09750 ABS & BA & TRAC & VSC SYSTEM. VSC warning light circuit
2WD: F13414 PRECHECK DI211 DI84M02 1. DIAGNOSIS SYSTEM (a) Check the warning lights. (1) Release the parking break pedal. (2) When the ignition switch is turned, check that the ABS warning light, VSC warning
More informationWIPER, WASHER & HORN SECTION WW CONTENTS ELECTRICAL WW-1 SERVICE INFORMATION... 2 REAR WIPER AND WASHER SYSTEM...25
ELECTRICAL SECTION WW A WIPER, WASHER & HORN B C D CONTENTS E SERVICE INFORMATION... 2 PRECAUTION... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 FRONT
More informationIsuzu. Chapter Testing Engine and Transmission Systems Engine And Transmission Code Reading Connectors and Locations
Chapter 10 Isuzu This chapter contains information for testing Isuzu vehicles with the Asian Import Vehicle Communication Software (VCS). The following Isuzu systems may be available for testing: Engine
More informationFault Codes. J control
J control Timer Temp Fault Codes 12 11 10 9 8 7 6 5 4 3 2 1 30 29 28 27 26 25 24 23 22 21 20 Enter unit inspection mode by pushing the UP and DOWN buttons simultaneously for two seconds. Ensure that the
More informationEG1 189 EFI SYSTEM 5S FE ENGINE DIAGNOSIS SYSTEM
5SFE ENGINE EG1189 DIAGNOSIS SYSTEM DESCRIPTION The ECU contains a builtin selfdiagnosis system by which troubles with the engine signal network are detected and a CHECK engine warning light on the combination
More informationThe engine is running. DTC P0351, P0352, P0353, and P0354 run continuously once the above condition has been met.
Page 1 of 6 DTC P0351-P0354 Circuit Description DTCs P0351 through P0354 Ignition Coil Primary/Secondary Feedback Circuit diagnostic monitors the primary circuitry of individual ignition coils for the
More informationSRS AIRBAG CONTROL SYSTEM
RESTRAINTS SECTION SRC A SRS AIRBAG CONTROL SYSTEM B C D CONTENTS E BASIC INSPECTION... 3 DIAGNOSIS AND REPAIR WORK FLOW... 3 Work Flow...3 INTERMITTENT INCIDENT... 5 Inspection Procedure...5 Trouble Diagnosis
More informationSEAT BELTS - AUTOMATIC
SEAT BELTS - AUTOMATIC 1990 Nissan 240SX 1990 ACCESSORIES/SAFETY EQUIPMENT Nissan Automatic Seat Belt Nissan; 240SX DESCRIPTION OPERATION Shoulder belt buckle mainly operates while ignition is ON. IGNITION
More informationDTC P0135, P0141, P0155, or P0161 (w/lr4 and LM7 w/ Delphi HO2S)
Page 1 of 5 2001 GMC Truck GMC K Sierra - 4WD Sierra, Silverado, Suburban, Tahoe, Yukon (VIN C/K) Service Manual DTC P0135, P0141, P0155, or P0161 (w/lr4 and LM7 w/ Delphi HO2S) Circuit Description This
More information2002 Buick Rendezvous - AWD
2002 Buick Rendezvous - AWD DTC P0410 Description The control module activates the secondary air injection (AIR) system by grounding both the pump relay and the vacuum control solenoid control circuits.
More information2012 Volkswagen Eos Komfort
Test-ID Specified value min. max. 1 Rich to lean sensor barrier - 0.6241 V voltage 2 Lean to rich sensor barrier - 0.6241 V voltage 7 Minimum voltage at sensor - 0.450 V for test cycle 8 Maximum voltage
More informationPRE-CHECK USA: DI-224 DLC1 E 1 ABS WITH EBD & BA & TRAC & VSC SYSTEM 2WD: CANADA: 4WD:
DI224 2WD: 4WD: USA: CANADA: F14323 PRECHECK DI8XO02 1. DIAGNOSIS SYSTEM (a) Inspect the battery positive voltage. Battery positive voltage: 10 14 V (b) Check the warning lights and buzzer. (1) Release
More informationDTC P1259: VTEC System Malfunction. Special Tools Required
DTC P1259: VTEC System Malfunction Special Tools Required Pressure gauge adapter 07NAJ-P07010A A/T low pressure gauge w/panel 07406-0070300 A/T pressure hose 07406-0020201 A/T pressure hose, 2,210 mm 07MAJ-PY4011A
More informationG - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
More informationMULTIPLEX COMMUNICATION SYSTEM
MULTIPLEX COMMUNICATION SYSTEM PRECAUTION 1 1. DISCONNECT AND RECONNECT CABLE OF NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following
More informationDTC P1518 Throttle Actuator Control (TAC) Module Serial Data Circuit
Page 1 of 6 DTC P1518 Throttle Actuator Control (TAC) Module Serial Data Circuit Circuit Description The throttle acuator control (TAC) module and the powertrain control module (PCM) communicate via a
More informationCharging System. Activity 11. Battery Drain Testing
Charging System 812FJ Student Manual Charging System Activity 11 Battery Drain Testing Performance Objectives: Test for and measure battery drain using manufacturer s service procedures. Diagnose the cause
More informationError code explanation Diagnostics...2 Error Code Chart...3 Tests Wiring diagram...6
Washer Tech Data Sheet This information is intended for Qualified Technicians Only. CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING Please Return This Sheet to its Envelope in the Product for Future
More information4/24/2014 ALLDATA Repair Toyota Truck Tacoma PreRunner V6-4.0L (1GR-FE) - Tire Pressure Monitor - Sensing Transmitter Activation
Title: TIRE PRESSURE SENSING TRANSMITTER ACTIVATION PROCEDURE Models: '06 Tacoma Introduction A tire pressure sensing transmitter is built into each tire valve. The measured tire pressure data is transmitted
More informationPRE-CHECK ABS Warning Light BRAKE Warning Light USA: USA: Canada: Canada: VSC Warning Light SLIP Indicator Light. TRAC OFF Indicator Light
ABS Warning Light BRAKE Warning Light USA: Canada: USA: Canada: VSC Warning Light SLIP Indicator Light TRAC Indicator Light F45096 PRECHECK 05765 05H3Y02 1. DIAGNOSIS SYSTEM (a) Check the warning lights.
More informationDiagnosis System DESCRIPTION AT 109
AT109 Diagnosis System DESCRIPTION 1. A selfdiagnosis function is built into the electrical control system. Warning is indicated by the overdrive OFF indica tor light. HINT: Warning and diagnostic trouble
More informationSUPPLEMENTAL RESTRAINT SYSTEM (SRS)
RESTRAINTS SECTION SRS A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2
More informationPRE CHECK. (b) In case of not using LEXUS hand held tester : Check the DTC. (1) Disconnect the short pin from DLC1.
DI 412 DIAGNOSTICS F02852 PRE CHECK DI28T 01 1. DIAGNOSIS SYSTEM (a) Check the warning lights and buzzer. (1) Release parking brake pedal. (2) When the ignition switch is turned, check that the ABS and
More informationSTARTING SYSTEM TEST STARTING SYSTEM
2013 Dodge or Ram Truck RAM 1500 Truck 2WD V8-5.7L Vehicle > Starting and Charging > Starting System > Testing and Inspection > Component Tests and General Diagnostics STARTING SYSTEM TEST STARTING SYSTEM
More informationENGINE IMMOBILISER SYSTEM
System Name Power Window Control System Sliding Roof System ENGINE IMMOBILISER SYSTEM PRECAUTION 1. PRECAUTION FOR DISCONNECTING BATTERY TERMINAL NOTICE: When disconnecting the negative () battery terminal,
More informationENGINE AND EMISSION CONTROL
17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL.......... 17-3 GENERAL DESCRIPTION...... 17-3 ENGINE CONTROL SYSTEM DIAGNOSIS.................. 17-3 INTRODUCTION TO ENGINE CONTROL SYSTEM
More informationBULLETIN TESTING. Article from Honda Service News. DTC P0341: CMP Sensor A and CKP Sensor Incorrect Phase Detected. Troubleshooting Flowchart
2005 Honda Truck CR-V 4WD L4-2.4L Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0341 BULLETIN TESTING Article from Honda Service News DTC P0341: CMP Sensor
More informationANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1993 Mitsubishi Diamante 1993 BRAKES Mitsubishi - Anti-Lock Brake System Diamante DESCRIPTION The Anti-Lock BRAKE SYSTEM (ABS) is designed to prevent wheel lock-up during heavy braking.
More informationDIAGNOSIS SYSTEM DESCRIPTION EG2 170
EG2170 DIAGNOSIS SYSTEM DESCRIPTION The ECM contains a builtin self diagnosis system by which troubles with the engine signal network are detected and a malfunction indicator lamp on the combination meter
More information1999 Chevrolet Tahoe - 4WD. DTC P1345 Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation
1999 Chevrolet Tahoe - 4WD DTC P1345 Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Circuit Description This diagnostic trouble code (DTC) monitors the crankshaft position (CKP) and the
More informationROAD WHEELS & TIRES SECTION CONTENTS E SUSPENSION WT-1
ROAD WHEELS & TIRES E SUSPENSION A SECTION ROAD WHEELS & TIRES B C D CONTENTS WT PREPARATION... 2 Special Service Tools... 2 Commercial Service Tools... 2 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...
More information17. ANTI-LOCK BRAKE SYSTEM (ABS; CBF1000A)
17. ANTI-LOCK BRAKE SYSTEM (ABS; CBF1000A) ABS SYSTEM LOCATION 17-2 ABS SYSTEM DIAGRAM 17-3 SERVICE INFORMATION 17-4 ABS CONNECTOR LOCATIONS 17-5 ABS TROUBLESHOOTING INFORMATION 17-7 ABS PROBLEM CODE INDEX
More information2005 Hyundai Truck Santa Fe V6-3.5L
2005 Hyundai Truck Santa Fe V6-5L Vehicle» A L L Diagnostic Trouble Codes ( DTC )» Testing and Inspection» P Code Charts» P0320 DTC P0320 IGNITION/DISTRIBUTOR ENGINE SPEED INPUT CIRCUIT Component Location
More informationPlease forward any questions or comments regarding this Troubleshooting Guide to
2009 Human Touch, LLC. All rights reserved. May 28, 2009 Please forward any questions or comments regarding this Troubleshooting Guide to documentation@humantouch.com. HT-1650 Troubleshooting This Troubleshooting
More informationIntermittent Battery Discharge
L-SB-0035-16 July 8, 2016 Service Category Power Source/Network Section Battery/Charging Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2013-2014 ES350, GS350 2014-2015 IS250, IS350 Introduction
More informationDTC P Shift Solenoid Circuit Electrical
1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Circuit Description The 1-2 Shift Solenoid Valve Assembly (1-2 SS Valve Assy.) controls the transmission fluid pressure on the 1-2
More informationU010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE
2014 - D2 - RAM 3500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL U010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE For a complete wiring diagram, refer to the Wiring Information. IGN RELAY-
More informationDiag. Code 22 Airbag Warning Light System Malfunction CIRCUIT DESCRIPTION ABT 71
SRS AIRBAG ABT71 Diag. Code 22 Airbag Warning Light System Malfunction CIRCUIT DESCRIPTION The airbag warning light is located on the combination meter. When the airbag system is normal, the airbag warning
More informationNEW FEATURES TIRE PRESSURE WARNING SYSTEM. 1. General GX470 NEW FEATURES
GX470 NEW FEATURES 5 NEW FEATURES TIRE PRESSURE WARNING SYSTEM 1. General When the tire pressure warning system detects that a tire inflation pressure becomes lower than the threshold (185 kpa, 1.9 kgf/cm
More informationGROUP 17 CONTENTS WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
17-1 GROUP 17 CONTENTS ENGINE CONTROL 17-4 GENERAL DESCRIPTION 17-4 ENGINE CONTROL SYSTEM DIAGNOSIS 17-4 INTRODUCTION TO ENGINE CONTROL SYSTEM DIAGNOSIS 17-4 ENGINE CONTROL SYSTEM DIAGNOSTIC TROUBLESHOOTING
More informationDistributor Ignition DI System Diagnosis
Page 1 of 8 2004 Chevrolet K Silverado - 4WD Sierra, Silverado VIN C/K Service Manual Engine Engine Controls - 4.3L Diagnostic Information and Procedures Document ID: 848577 Distributor Ignition DI System
More information2/2/2018 Feed Circuit Test (Starting System) - ALLDATA
2005 Jeep Truck Grand Cherokee 2WD V8-5.7L VIN 2 Vehicle > Starting and Charging > Starting System > Testing and Inspection > Component Tests and General Diagnostics FEED CIRCUIT TEST The starter feed
More informationB1C29 LEFT SIDE SEAT THORAX S... B1C29 LEFT SIDE SEAT THORAX SQUIB 1 OPEN. 6/14/2016 Direct Hit Search
B1C29 LEFT SIDE SEAT THORAX S... B1C29 LEFT SIDE SEAT THORAX SQUIB 1 OPEN http://dh.identifix.com/searchfixes/index?roid=136882799&vid=2377948&vsm=1&locationid=2#kw=b1c2d+b1c29&soption=1&vetid=1&stmode=1&p
More informationDTC P0420. Circuit Description. Conditions for Running the DTC.
Page 1 of 5 DTC P0420 2003 Buick LeSabre LeSabre (VIN H) Service Manual Document ID: 792202 Circuit Description In order to control emissions of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen
More informationLAN SYSTEM SECTION CONTENTS K ELECTRICAL LAN-1 CAN
K ELECTRICAL A SECTION LAN SYSTEM B C D CONTENTS E CAN PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions When Using CONSULT-II...
More informationDOOR & LOCK SECTION DLK CONTENTS BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY DLK-1 BASIC INSPECTION... 6 FUNCTION DIAGNOSIS...10
BODY EXTERIOR, DOORS, ROOF & VEICLE SECURITY SECTION DLK A DOOR & LOCK B C D CONTENTS E BASIC INSPECTION... 6 DIAGNOSIS AND REPAIR WORKFLOW... 6 Work Flow...6 INSPECTION AND ADJUSTMENT... 9 ADDITIONAL
More informationEmission Control System
Emission Control System Exhaust Gas Recirculation (EGR) System [B18A1 engine: A/T] Troubleshooting Flowchart The Malfunction Indicator Lamp (MIL) indicates Diagnostic Trouble Code (DTC) 12: A problem in
More information1 of 87 12/22/2014 1:53 PM 2006 Lexus GS 300 3.0L Eng VARIABLE GEAR RATIO STEERING SYSTEM PRECAUTION CAUTION: If the negative (-) battery cable has been disconnected, initialize the following systems when
More informationDescription. Shift solenoid valve A ON (Closed) OFF (Open) OFF (Open) ON (Closed)
Description DTC P0750 SHIFT SOLENOID VALVE A Description NFAT0067 Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the park/neutral position (PNP) switch,
More informationDTC P2100, P2103 THROTTLE CONTROL MOTOR RELAY
DTC P2100, P2103 THROTTLE CONTROL MOTOR RELAY Component Description INFOID:0000000001702985 Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle
More informationSRS AIRBAG CONTROL SYSTEM
RESTRAINTS SECTION SRC A SRS AIRBAG CONTROL SYSTEM B C D CONTENTS E PRECAUTION... 4 PRECAUTIONS... 4 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...4 Precaution
More informationSUPPLEMENTAL RESTRAINTS SYSTEM
SECTION 8B SUPPLEMENTAL RESTRAINTS SYSTEM CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with
More informationTIRE PRESSURE WARNING SYSTEM
CH-84 TIRE PRESSURE WARNING SYSTEM DESCRIPTION A direct-sensing type tire pressure warning system has been newly provided as standard equipment on the U.S.A. models. If the vehicle continues to be driven
More information14.Diagnostic Procedure with Diagnostic Trouble Code (DTC)
14.Diagnostic Procedure with Diagnostic Trouble Code (DTC) A: DTC C2021 TIRE 1 AIR PRESSURE DECREASE Refer to DTC C2024 for diagnostic procedure.
More informationP0882-TCM POWER INPUT LOW
- JK - JEEP WRANGLER - L V6 (SMPI) P-TCM POWER INPUT LOW BATTERY BATT A FUSE J 5A POWER DIESEL GAS Z 6 BK Z 4 BK Z 6 BK 5 7A 7 6 ELECTRONICS 6 C C T6 6 T5 YL/OR YL/BR 5 C C T6 6 T5 YL/OR YL/BR S6 T6 T6
More information