GM TRUCK Double Din Head Unit Install Kit
|
|
- Evelyn Fleming
- 5 years ago
- Views:
Transcription
1 GM TRUCK Double Din Head Unit Install Kit Please read all instructions including the *install tips* first! 1. Disconnect the vehicle s battery. 2. Remove the dash panel; Lower the tilt on the steering column to its lowest position, press your park brake fully, put the key in the ignition and turn it forward (but do not start the vehicle) and shift the vehicle into a low gear to allow room around the shift lever to remove the plastic panel. *Keep your foot on the brake when taking vehicle out of park!!* Very carefully, pull the exterior dash panel straight out, starting at the top and it will pop loose. Fully remove the panel and place the vehicle back into PARK. 3. Remove the factory (or aftermarket head unit) and the HVAC controls by unclipping them from the internal dash. Also remove the factory CD player (if equipped) or the cubby hole. 4. Unclip all wire harnesses from the HVAC unit and remove the unit from the vehicle. Using a saw or sander, remove all mounting tabs from this unit until all outer sides are smooth, see pic below. Set the unit aside until it is needed for reinstallation. Page 1
2 5. With the dash apart, use the mounting bracket and the pic below as a guide to show you what internal dash plastic must be trimmed. A small reciprocating air saw would be ideal to use but a Dremel with a cut off wheel will work as well. *Be careful not to cut through the lower right, external dash mounting tab. It s the square hole to the left of the cup holder as seen in pic.* 6. Test fit the mounting bracket into the dash to make sure all inner dash plastic is sufficiently trimmed. 7. Install the HVAC controls into the lower pocket of the mounting bracket. Space the HVAC controls out from the face of the mounting bracket s lower hole 1/8. See pic. *A kit will soon be released that will allow you to re-install your modified HVAC unit back into your dash if you wish to remove your double din and take your vehicle back to stock. A replacement dash panel will need to be purchased to complete the transition back to stock.* Page 2
3 8. Pre-drill holes for the #4 screws with the supplied drill bit. Use extreme caution to drill only as deep as necessary to prevent damage to the internal HVAC components. See Pic. 9. Very slowly and very carefully use the supplies #4 screws to secure the HVAC control box to the mounting bracket. The plastic on this box is very thin and fragile and will crack easily. *Do not install the head unit step #14* 10. Install the mounting bracket with the HVAC unit into the vehicle. Use the supplied, self-drilling #6 screws to secure the bracket to the vehicle s inner dash structure. The mounting brackets allows for the use of 4 screws per side. Page 3
4 11. The center section of the external dash (cover) needs to be cut out. Using a small reciprocating air saw or dremel, cut along the outside edge of the center section where it corners up. Cut the area out smaller than needed and sand the opening larger as needed, using the new plastic section as a gauge. See pic. 12. Install the exterior dash panel that you just cut out onto the vehicle for a test fit. The area you want to examine is around the HVAC unit. It may be necessary to remove some material from the left corner of the HVAC box as well as some plastic on the back side of the exterior dash cover to allow for the exterior dash panel to sit flush once reinstalled. See pics. Page 4
5 *VERY MINIMAL Sanding of the corner of the HVAC control box might be necessary as well.* *Do not sand any more of the corner of the HVAC box than necessary, you do not want the sanded edge to be seen once the dash is remolded* 13. Disassemble the dash and remove the mounting bracket. Page 5
6 14. Install your head unit on the mounting bracket. You can either use the sleeve provided with your head unit, or ISO install using the mounting holes and spaces provided. YOU MUST FIGURE HOW LONG AND WHAT SIZE OF BOLTS TO USE FOR THIS! TOO LONG OF BOLTS CAN DAMAGE YOUR HEAD UNIT. I TAKE NO RESPONSIBILITY FOR YOUR ERRORS!! 15. Plug in all wires to your head unit and HVAC unit and install the assembled bracket (HVAC, head unit) into the dash 16. Now focus in the external dash section. Test fit and check the alignment of the new dash section before gluing it into place. Make any adjustments if necessary and glue the new dash section in place. The backside of the new dash section has a shoulder around the outside perimeter. This goes behind the dash panel and provides a glue seam to bond the two plastics. Allow it to dry completely before attempting to reassemble the dash. *Norton Speed Grip is a recommended epoxy, but many others will work.* 17. Plastic fill all seams or gaps and sand smooth. Paint to desire. 18. Reassemble your dash; Be careful when putting the plastic back on to not contact your head unit and scratch or damage the screen. If you have purchased this item through E-bay please note: I will gladly leave you positive feedback immediately AFTER feedback is received for me so I know you are completely satisfied with your purchase. If you have any questions feel free to contact me. Anderson@TheDetailSS.com Thank you, Sean Anderson Page 6
94-96 Impala SS & Caprice Double Din Head Unit Installation Kit
.. 94-96 Impala SS & Caprice Double Din Head Unit Installation Kit Please read all instructions including the install tips first! You must notch or drill the inner dash plastic in two spots. Two holes
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationChevrolet Impala 2014-up* *Visit MetraOnline.com for up-to-date vehicle specific applications. KIT FEATURES
99-3024B INSTALLATION INSTRUCTIONS KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted matte black to match the factory finish KIT COMPONENTS A) Radio trim panel B) Radio
More informationChrysler/Dodge/Jeep (without NAV)
Installation instructions for part 99-6507 Chrysler/Dodge/Jeep (without NAV) 2005-2010 99-6507 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket WIRING & ANTENNA CONNECTIONS
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationDash Procedure (Dash Cluster Corvette) for color upgrade
Dash Procedure (Dash Cluster 1984-1989 Corvette) for color upgrade Chapter 1 Please read all instructions before proceeding. 1. Disconnect negative battery cable. 2. Use small flat blade screw driver to
More informationVTCM Installation Manual Table of Contents
VTCM Installation Manual Table of Contents 1. Introduction:... 2 2. Disclaimer:... 2 3. Software / Drivers:... 2 a. Plugging in the controller:... 2 b. Install 4.0.NET Frame work:... 3 c. Install COM port
More informationAcura/Honda/Isuzu AT-807HD, IBR-807HD, CF-807HD, AW-807HD
Installation instructions for part Acura/Honda/Isuzu 1988-2006 99-7898 AT-807HD, IBR-807HD, CF-807HD, AW-807HD WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: Not Required KIT FEATURES DIN
More informationNissan 370Z 2009-up (without navigation) B
REV. 4/2/2014 INST99-7607B INSTALLATION INSTRUCTIONS FOR PART 99-7607B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte black to match
More information67-70 Cougar Rack Kit Instructions # &
67-70 Cougar Rack Kit Instructions # 8011950-01 & 8011940-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty on
More informationRetrofitting an R Instrument Cluster
Retrofitting an R Instrument Cluster This is a step-by-step tutorial for those wishing to incorporate the unique look of the R instrument gauges to their current modules. Before starting, be certain that
More informationChrysler Multi-kit TABLE OF CONTENTS Dash Disassembly...2 Kit Assembly
99-650345 INSTALLATION INSTRUCTIONS Chrysler Multi-kit 1998-2010 INTRODUCTION This instruction booklet will cover (3) different kits, yet carry the same applications and dash disassembly. After dash disassembly
More informationInstallation Instructions Pro Stick Shifter
Installation Instructions Pro Stick Shifter Part Number 80701, 80702 & 80706 2012, 2010, 2008, 2001, 1998 by B&M Racing and Performance Products The B&M Pro Stick shifter #80701 and #80706 comes equipped
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationToyota Sequoia / Tundra
Installation instructions for part 99-8256 Toyota Sequoia 2003-2007 / Tundra 2003-2006 99-8256 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket ISO DDIN radio provision
More informationINSTALL INSTRUCTIONS: Blend Door Repair Kit
Dorman Products A/C Blend Door Repair Tool For 2006 Chevrolet Equinox / Pontiac Torrent 902-600 Installation Instructions Parts Included 1. Plastic Replacement Sleeve 2. Mounting Plate 3. Saw 4. Drill
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0033 Fits: 2013-15 F01 B7, 750i & xdrive (N63TU engine) 2013-15 F02 B7L, 750Li & xdrive (N63TU engine) PARTS LIST Left and right carbon fiber air box lids
More information6th generation (2015+) Mustang Harness Mount Bar Installation Instructions
R-1180 6th generation (2015+) Mustang Harness Mount Bar Installation Instructions A. Install harness bar 1. Remove front seats. First remove the plastic bolt covers front and rear using a small flat head
More informationPolaris Slingshot 2015-up* *Visit MetraOnline.com for up-to-date vehicle specific applications.
99-9721 INSTALLATION INSTRUCTIONS Polaris Slingshot 2015-up* *Visit MetraOnline.com for up-to-date vehicle specific applications. KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision
More informationTutorial:Head Unit Installation
Tutorial:Head Unit Installation From Tech Wiki : Nissan 350Z : Infiniti G35 : Nissan GT-R Here, I installed the Kenwood DDX7015 touch screen DVD system. I made this step-by-step tutorial to help those
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda For Models With Manual Climate Controls TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR PART 99-7509 APPLICATIONS Mazda 5 2006-2007 For Models With Manual Climate Controls 99-7509 KIT FEATURES Painted To Match Factory Dash DIN Radio Provision with Pocket ISO
More informationHyundai Elantra / Sonata / Tiburon (all but SE) Kia Optima (2006 Early Production Models Only)
Installation instructions for part 99-7371 Hyundai Elantra 2001-2006 / Sonata 2002-2005 / Tiburon (all but SE) 2003-2008 Kia Optima 2001-2006 (2006 Early Production Models Only) 99-7371 KIT FEATURES ISO
More informationAEROMOTIVE Part # & Stealth Fuel Tank Sump INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 18651 & 18652 Stealth Fuel Tank Sump INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationLast Revision: 09JA THROUGH 1976 GM A & F-CAR TILT STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #3
Last Revision: 09JA2010 1969 THROUGH 1976 GM A & F-CAR TILT STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #3 Disassembly and Repair Instructions Addressed in this Paper Degree of Difficulty Page
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationHyundai/Kia multi-kit INST-123KI
Installation instructions for part Hyundai/Kia multi-kit 1995-2010 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted to match factory color and finish KIT COMPONENTS A)
More informationChrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up B
Installation instructions for 99-6518B Chrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 99-6518B KIT FEATURES ISO DIN radio provision
More informationIf you study the Mercedes Documents (pictured below) for several minutes before you start, you will understand them as you proceed.
Removing the C32 center dash panel and radio These are not my instructions, they were garnered from the web, I merely pasted them onto a doc file. There is Air Bag wiring nearby. If you feel uncomfortable
More informationLincoln Navigator / MKX Lincoln MKZ / Zephyr 2006 (excludes models equipped with factory navigation)
99-5813 INSTALLATION INSTRUCTIONS Lincoln Navigator 2007-2014 / MKX 2007-2010 Lincoln MKZ 2007-2009 / Zephyr 2006 (excludes models equipped with factory navigation) KIT FEATURES DIN radio provision with
More information09-12 Dodge 4WD Leveling Kit
9235900 09-12 Dodge 4WD 1500 2.5 Leveling Kit Thank you for choosing Rough Country for all your suspension needs. DOES NOT FIT TRX PACKAGE VEHICLES!! Rough Country recommends a certified technician install
More information2007-up Cadillac Escalade
INTALLATION INTRUCTION FOR PART 99-2007 APPLICATION 2007-up Cadillac Escalade 99-2007 KIT FEATURE DIN radio provision with pocket IO radio provision with pocket Double DIN radio provision KIT COMPONENT
More information4-Runner Sport/SR Highlander (without NAV)
Installation instructions for part 99-8258 REV. 5/11/2016 INST99-8258 4-Runner Sport/SR5 2003-2009 Highlander (without NAV) 2001-2007 99-8258 KIT FEATURES DIN radio provision with pocket ISO DIN radio
More informationTOYOTA 4 RUNNER 2010-UP
INSTALLATION INSTRUCTIONS FOR PART 99-8227S KIT FEATURES KIT COMPONENTS APPLICATIONS TOYOTA 4 RUNNER 2010-UP U.S. PATENT # D639,292 99-8227S DIN Head unit provisions with pocket ISO DIN Head unit provision
More informationBA/BF ICC Install Instructions - DISCONNECT BATTERY Negative terminal.
BA/BF ICC Install Instructions - DISCONNECT BATTERY Negative terminal. Step 1. (Figure 1) Remove the plastic gearshift surround by lifting it straight up. Lifting from the raised bump that we are pointing
More informationUpper Class Grille. Main Grille - # / # Dodge Charger. GRILLE Installation Guide. Parts included (1) Main Grille.
Main Grille - # 51480 / #54480 Parts included (1) Main Grille Polished - Part #51480 OR Black - Part #54480 Hardware included (8) - 3/4 x 5/8 L Brackets (8) - #6-32 Nylon Nuts (8) - 3/16 x 1 x 1/32 Black
More informationINSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0390C APPLICATION: 1999-2003 E39 M5 PARTS LIST 1 Left Aluminum Intake Tube 1 Air Pump Bracket (A) 1 Right Aluminum Intake Tube 1 Air Pump Bracket
More informationAcura TSX 2009-up CH
INSTALLATION INSTRUCTIONS FOR PART KIT FEATURES ISO Double DIN radio provision Painted charcoal gray APPLICATIONS Acura TSX 2009-up Table of Contents Acura TSX 2009-up...2-5 Kit Assembly ISO Double DIN
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More informationPRODUCT USE INFORMATION
9RC61000 Jeep YJ Body Lift Thank you for choosing Rough Country for all your suspension needs. This body lift fits both manual and Automatic equipped vehicles!!! Refer to last page of this Instruction
More informationSHARK UPPER WINDSHIELD FRAME & WINDSHIELD REPLACEMENT. Text and Photos by TOM BENFORD
Text and Photos by TOM BENFORD I purchased a fathom green 69 big-block tri-power T-top coupe with only 42,000 original miles on it recently. I'm the third owner of the car, and I got it for a very good
More informationFord Mustang CH
Installation instructions for part KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket Double DIN radio provision Painted charcoal to match factory dash Ford Mustang 2010-2014
More informationStephenson's Valve Gear: 7mm cast white-metal kit 19 th Century swing-link version - non-working, cosmetic only. Instructions
SER-Kits Stephenson's Valve Gear: 7mm cast white-metal kit 19 th Century swing-link version - non-working, cosmetic only Page 1 of 5 Instructions HEALTH & SAFETY: The castings contain some lead. Dispose
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationJass.Performance Low Profiles Installation Manual
Jass.Performance Low Profiles Installation Manual The Jass.Performance Low Profiles are featuring: Fully reversible upgrade of the stock headlight bodies. Premium branded E-signed, TÜV aprooved Hella Headlights
More informationMercedes Benz SLK Class
INSTALLATION INSTRUCTIONS FOR PART 99-8713 KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision APPLICATIONS See application list inside Mercedes Benz
More informationToyota Tacoma
Installation instructions for part 99-8214 REV. 3/7/2017 INST99-8214 Toyota Tacoma 2005-2011 99-8214 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket ISO DDIN radio provision
More information1464. Interior Installation. Cover Rear Seat Support Cut the vinyl to approximately the size of the rear seat support.
Chapter 37 (Video Clip 37) - Interior Installation 1464. Interior Installation Cover Rear Seat Support 1465. Cut the vinyl to approximately the size of the rear seat support. 1466. Make a dry fit of the
More informationHonda Civic
Installation instructions for part 99-7816 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted to match factory dash: 99-7816G = Gunmetal, 99-7816T= Taupe Honda Civic 2006-2011
More informationCJ1278 IN-DASH INSTALLATION KIT FOR SELECT 1974-UP CHRYSLER AND JEEP VEHICLES INTRODUCTION PRELIMINARY PARTS LIST ASSEMBLING THE KIT
INTRODUCTION The Scosche in-dash Installation Kit for 1974-UP Chrysler and Jeep Vehicles provides the parts you need to mount your car stereo/cassette player into your vehicle's dash. Refer to the individual
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationMazda S
INSTALLATION INSTRUCTIONS FOR PART 99-7523S KIT FEATURES Double DIN radio provision ISO DIN radio provision with pocket Painted silver Pre-wired ASWC-1 harness included (ASWC-1 sold separately) APPLICATIONS
More information1969 THRU 1982 C3 CORVETTE TILT AND TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER
Last Revision: 09JA2010 1969 THRU 1982 C3 CORVETTE TILT AND TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree of
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: F10 M5 # D Fits: F06/F12/F13 M6 PARTS LIST
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0035 Fits: 2013-15 F10 M5 # D760-0037 Fits: 2012-15 F06/F12/F13 M6 PARTS LIST (1) Left Carbon Airbox Lid (1) Right Carbon Airbox Lid (1) Left Carbon Snorkel
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationToyota RAV up
REV. 2/27/2014 INST99-8217 INSTALLATION INSTRUCTIONS FOR PART 99-8217 APPLICATIONS See application list inside Toyota RAV 4 2006-up 99-8217 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR PART 99-7504 APPLICATIONS Mazda 3 2004-2008 99-7504 KIT FEATURES DIN Mount Radio Provision with Pocket ISO Mount Radio Provision with Pocket onus Display Replacement Pocket
More informationCAR STEREO CONNECTORS
1996-98 Jeep Grand Cherokee 1. Extract (5) screws from along top of dash instrument bezel. 2. Carefully pop out wood grain trim panel around a/c heater control. 3. Carefully pop out wood grain trim panel
More informationShort Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
More informationOEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number )
OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents
More informationInstallation Instructions
Installation Instructions 5 COILOVER CONVERSION FTS24087 2007-15 JEEP JK PARTS LIST: FTS24087BK 5" JK CO Hoop BX FT50377 Hardware Sub- Assembly QTY Part # Description QTY Part # Description 1 FT50349BK
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationRetrofit Steering Column
Retrofit Steering Column INSTALLATION INSTRUCTIONS for 1965 Ford Falcon FOR PART NUMBER S: 1170906010, 1170906020, 1170906051, 1130906010, 1130906020, 1130906051 S INCE 1986 www.ididitinc.com 610 S. Maumee
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationIn area - A -, a proper seal must be made against the top of the window glass.
Door window, adjusting Page 1 of 3 Audi > B3 > 1994-1998 Body Exterior, Interior 61 - Convertible top, checking and adjusting Door window, adjusting Sections C-C and D-D. Adjust door window so that window
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationspec.dock BMW 5-Series e60 v.2 Installation Instructions
Thank you for your purchase of a spec.dock ipod solution for your vehicle. Audio connections may vary according to your particular setup. 2point5 recommends having your spec.dock integrated by a certified
More informationTru-Billet Climate Control Knob Installation Instructions
P/N S197-525-07 2007-08 Tru-Billet Climate Control Knob Installation Instructions Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the installation.
More informationHyundai Sonata GLS/SE (without NAV) 2011, Sonata (without NAV) , Sonata Hybrid (without NAV)
Installation instructions for part 99-7342 REV. 3/21/2017 INST99-7342 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted black and silver to match factory dash KIT COMPONENTS
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More information2010 Toyota Prius model II Head Unit Upgrade
2010 Toyota Prius model II Head Unit Upgrade Monday, December 21, 2009 Disclaimer: Use this document and its contents at your own risk. Forward: Huge thanks to those members on Priuschat.com that forged
More informationPlease pay attention to all Cautions and Notes within these instructions.
Mustang Cluster Kit - INSTALLATION INSTRUCTIONS - For use with Ford Mustang (1994-1998) and Simco Kit Part # s 2034-7XX Revised: Dec 30, 2008 Rev. C Please read and understand all instructions before attempting
More informationor Chrysler Multikit 2007-up* TABLE OF CONTENTS See page 2 KIT FEATURES
95-6511 or 99-6511 INSTALLATION INSTRUCTIONS 95-6511 ISO DDIN radio provision Textured 99-6511 DIN radio provision with pocket ISO DIN radio provision with pocket KIT COMPONENTS 95-6511 A) Long nose (wide)
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal: Release these clips
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationMustang Clear Lens Instrument Cover (90-93) - Installation Instructions
Mustang Clear Lens Instrument Cover (90-93) - Installation Instructions The below installation instructions work for the following products: Mustang Clear Lens Instrument Cover (90-93) Please read through
More informationToyota 4-Runner (Excluding Limited) Toyota Highlander
INSTALLATION INSTRUCTIONS FOR PART 99-8206 APPLICATIONS Toyota 4-Runner (Excluding Limited) 2003-2009 Toyota Highlander 2001-2007 99-8206 KIT FEATURES DIN head unit provision with pocket ISO DIN head unit
More informationMiG-15 ARF Assembly & Operation Manual
INLET PREP The MiG-15 inlet system has been accurately assembled at BVM. The following steps are required by the modeler prior to installation in the model. The inlet duct system is not glued into the
More informationTOYOTA SUPRA JZA80 HEADLIGHT LENS TUTORIAL
TOYOTA SUPRA JZA80 HEADLIGHT LENS TUTORIAL Disclaimer: Original Motorsports takes no responsibility for any errors which may occur in your DIY project. This is simply a guide. If you are not confident
More information1967 (Late) CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 03SE2012 1967 (Late) - 1968 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More informationStealthbox. STEP 1: Engage the emergency brake. Place the key into the ignition and turn to the accessory position.
Stealthbox INSTALLATION GUIDE for the SB-GM-BURBSCNSL/10W3v2 (2003-Up Chevrolet Suburban,Tahoe, Silverado & GMC Yukon,YukonXL, Sierra with front bucket seats and center console) START HERE Read the instructions
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More information60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # , , &
60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # 8011740-01, 8011900-01, & 8011920-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer
More informationxpressstart Mercedes Solution Mercedes Benz S and CL Class
DIGITAL REMOTE START SYSTEM WWW.XPRESSKIT.COM MADE IN THE USA xpressstart Mercedes Solution 2007-2012 Mercedes Benz S and CL Class Tools you will need -T-25 Torx Driver -Panel Removal tool -3/4 Drill bit
More informationMARDER II ENGINE COMPARTMENT
TWS 353048 MARDER II ENGINE COMPARTMENT Congratulations on purchasing one of the finer aftermarket resin conversion sets available. This kit was Mastered by Tom Kondziolka. This kit is intended to be used
More informationFord multi-kit 2004-up
INSTALLATION INSTRUCTIONS FOR PART 95-5812 APPLICATIONS See application list inside Ford multi-kit 2004-up 95-5812 KIT FEATURES Double DIN radio provision Stacked ISO units provision KIT COMPONENTS A)
More informationPRO RATCHET UNIVERSAL SHIFTER
Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationThis write-up is subject to revision. PM me, eb2143 at tdiclub.com and I will update it if there are inaccuracies, typos, missing information, etc.
1 A4 Door Switch Replacement, 1.0 Notes on this guide: The following guide is mostly a combination of two write-ups by VgRt6 on Vwvortex.com. Specific threads located here: http://forums.vwvortex.com/showthread.php?1015107
More information*70200BAG1* 70200BAG FORD F150 GRILLE LIGHT MOUNT
927020000 *70200BAG1* 70200BAG1 2015-2018 FORD F150 GRILLE LIGHT MOUNT PRIOR TO INSTALLATION Make sure the kit is complete and you have read these instructions thoroughly before beginning installation.
More informationLast Revision: 30JN THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 30JN2007 1969 THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationB. Land Rover Range Rover
99-9402B INSTALLATION INSTRUCTIONS KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted black KIT COMPONENTS A) Radio trim panel B) Radio brackets C) Radio bracket adapters
More information2011 Hyundai Sonata
KIT FEATURES INSTALLATION INSTRUCTIONS FOR PART 99-7343 APPLICATIONS 2011 Hyundai Sonata (For models equipped without Nav and with auto climate controls) 99-7343 ISO DIN head unit provision with pocket
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationFord multi-kit 2004-up
INSTALLATION INSTRUCTIONS FOR PART 99-5812 APPLICATIONS See application list inside Ford multi-kit 2004-up 99-5812 KIT FEATURES DIN head unit provision with pocket ISO DIN head unit provision with pocket
More informationHood Lift Kit Installation Instructions For Mazda Miata PART # , ,
Tools required: Rivet gun, masking tape, small flat screw driver, 10mm combination wrench, two13mm combination wrenches, two 17mm combination wrenches. Read and understand these instructions before attempting
More informationWARNING. BX Nissan Sentra S/SV/SR/SL Installation Instructions
Attachment Tab Height: 14 Attachment Tab Width: 22 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are
More information