3010 Series. 4 Latch. Hold Open Arm Door Closers Regular Arm. Installation Sequence. Mark and Drill Holes. Parts. Sweep. Set Hold Open.

Transcription

1 000 eries Tri-Packed Non Handed Closer Instructions eft Hand - H ight Hand everse - H eft Hand - H ight Hand everse - H egular rm ee Page ee Page 5 eft Hand - H ight Hand everse - H Parallel rm ee Pages & 4 Hold Open rm Models ized djustable (izes,,4,5,) (izes 1 thru ) CUTION n Increctly installed improperly adjusted do closer can cause property damage personal injury. These installation instructions should be followed to avoid the possibility of misapplication misadjustment. "D suffix (Delayed ction) is an optional feature. NOTE: F special applications a separate do and frame preparation template is packed with these instructions. Use this instruction sheet f installation sequence and closer adjustments only. s should be hung on ball bearing antifriction hinges. separate do stop is recommended. and frame must be properly reinfced. djust closing time speed between and 7 seconds from 90 to 0. Greater closing times may be required f elderly handicapped. These do closers should NOT be installed on the exposed side (weather side) of exteri dos. Metal Wood ight Hand - H eft Hand everse - H egular rm ee Page ee Page 5 elf Drilling crews Wood and Metal ight Hand - H eft Hand everse - H Parallel rm ee Pages & 4 ight Hand - H eft Hand everse - H () leeve Nut and olt ackcheck Valve atch Valve Power djustment haft #7 Clips 1/4-0 crew /1" Insert Insert Cutouts F Wood drill /1 hole Machine crews #7 Drill, 1/4-0 Tap Drill 9/ thru from Closer ide /8 Drill other side Thru olt and Grommet Nut Drill 9/ thru from Closer ide /8 Drill other ide tandard 10 Narrow weep Valve offit dapter Plate 588 offit Plate Used with Parallel rm Closers Only n O Group brand Closer ody et crew crews rm ssembly Main rm 500M eries Metal tandoffs crew tandard 510 Full tandoff NOTE: rchitectural CN crews NOT be used f dos swinging over 0 using parallel mount 510 rchitectural Metal Insert tandoff Insert Cutouts 510 rchitectural Plastic crew Pack Pinion Cap

2 010 eries Parts 1 Hold Open rm Closers egular rm Mark and Drill Holes 5-1/ (140 1-/4 (44) 1-/8 (5) 1-1/ (8) /4 (19) (04.8) equence ight Hand hown D C eft Hand Nut Down Opening To to to 180 Dimension "" 7-1/ (191) (15) 4-1/ (114) Inches (mm) /Wall/Hardware/Jamb conditions permitting weep 4 atch 5 F 90 E H G H F 510 rchitectural Only ackcheck pring Power djust (If Necessary) et Hold Open 7 Pinion Cap 8 90 min. Don't completely close valve () crew pinion cap onto pinion shaft by hand with a Phillips screw driver - DO NOT OVE TIGHTEN. n O Group brand

3 010 eries Parts 1 Hold Open rm Closers Parallel rm Mark and Drill Holes -/4 (70) (50) /8 (10) equence F 1-1/ E 158 Plate D 7/1 (11) ight Hand hown Top of Frame 1/ (1) C C -5/8 (9) G F 510 rchitectural Only Close Valves /4 (19) Inches (mm) /Wall/Hardware/Jamb conditions permitting (04.8) Opening To 0 1 to Install Closer and racket Preload Closer 9-1/ (41) 7 (178) -/4 (95) 1-1/4 () Place rm on pindle weep eft Hand ight Hand Up atch Down otate emove rm from pindle n O Group brand

4 010 eries Hold Open rm Closers Parallel rm Install rm Open Valves 8 ssemble rm 9 ight Hand Flat weep eft Hand atch Flat ttach rm crew 10 Don't remove valves 11 weep atch 1 1-1/ (8) pring Power djust (If Necessary) ackcheck 14 et Hold Open 15 Pinion Cap 1 () n O Group brand Don't completely close valve crew pinion cap onto pinion shaft by hand with a Phillips screw driver - DO NOT OVE TIGHTEN. 4

5 010 eries Parts 1 Hold Open rm Closers rm Mark and Drill Holes Inches (mm) 1-7/8 (48) (04.8) /4 (19) 1-/4 (44) 5-1/ (140) 1/ (1) Top of Frame equence H E 90 ight Hand hown Opening To to to 180 /Wall/Hardware/Jamb conditions permitting Dimension "" 7-1/ (191) (15) 4-1/ (114) longer connecting rod is required f reveals greater than " (7) C eveal weep 4 atch 5 D eft Hand Nut Up G C F H pring Power djust (If Necessary) ackcheck F 510 rchitectural Only et Hold Open 7 Pinion Cap 8 () 70 to 180 Don't completely close valve crew pinion cap onto pinion shaft by hand with a Phillips screw driver - DO NOT OVE TIGHTEN. 5 n O Group brand

6 weep (Use 1/8" Hex Wrench f these djustments) atch ackcheck COED pring Power djust 110/10/510 djustment Chart DOO EXTEIO INTEIO TPE OF INT. egular rm Parallel rm egular rm Parallel rm FU 0 TUN OF 5/1 POWE DJUTMENT WENCH (0.85M) Number of Turns equired MXIMUM DOO IE (0.90M) 4 (1.00M) 48 (1.0M) FU (0 ) TUN MXIMUM VIE Closer is shipped set at mid range setting = 10 turns (Use 5/1 socket adjustable wrench f this adjustment) To identify your model: To et Hold Open Closer ize lank = 11/511 = /5 = 1/51 4 = 14/514 5 = 15/515 = 1/51 1F Open to Desired ngle Use 1" Wrench Mfg. Date Product uppt Tel ale ocks & Hardware is a division of ale ecurity Inc., an O Group company. ale is a registered trademark of ale ecurity Inc., an O Group company. Other products' brand names may be trademarks registered trademarks of their respective owners and are mentioned f reference purposes only. These materials are protected under U.. copyright laws. ll contents current at time of publication. ale ecurity Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/ its materials. Copyright 004, 01, ale ecurity Inc., an O Group company. ll rights reserved. eproduction in whole in part without the express written permission of ale ecurity Inc., an O Group company is prohibited. n O Group brand