Battery Master Switches

Transcription

1 Battery Master All of these switches are designed to be fitted to the earth side of the battery, except for which is fitted on the live side Panel mounted switch With removable knob. Requires hole size 22mm diameter. Rated for a continuous load of 100 amps on 12V systems each 9.29 ex VAT Panel mounted switch with waterproof cap FIA approved. With removable knob and diode. Requires hole size 60 x 18mm. Rated for a continuous load of 100 amps on 12V systems each ex VAT Spare key each 3.95 ex VAT Spare resistor each 2.95 ex VAT Panel mounted switch with waterproof cap With removable knob and waterproof cap. Requires hole size 22mm diameter. Rated for a continuous load of 100 amps and intermittent loads of up to 500 amps for 10 seconds on 12V systems SSB each ex VAT (Right) Spare key SSB each 3.25 ex VAT discarnect Post mounted Discarnect master switch, mounts to battery posts, including Ford style lug. Rated for a continuous load of 100 amps on 12V systems. To immobilise the car unscrew and remove the knob. The 16 amp by-pass fuse maintains current to all electrical circuits (alarm, stereo memories etc.). Because the starter motor draws over 150 amps, any attempt to operate or hot wire the starter motor will cause the fuse to blow, immobilising the car until the knob is screwed back on each ex VAT Panel mounted switch with winged Knob LUCAS original with winged knob. Requires hole size 19.5mm diameter. Rated for a continuous load of 150 amps and intermittent loads of up to 1500 amps on 12V systems SSB each ex VAT A good reproduction of SSB106. Rated for a continuous load of 100 amps on 12V systems each ex VAT Panel mounted switch with round Knob A good reproduction of Battery Master Switch SSB103 as fitted to Austin Healey. Requires hole size 43mm diameter. Rated for a continuous load of 150 amps and intermittent loads of up to 500 amps for 45 seconds on 12V systems each exvat 51

2 Toggle +44 (0) Toggle general PurPose Off-on with chrome bezel. Rated at 5 amps maximum on 12v systems SPB each ex VAT Reproduction SPB200/R 7.20 each 6.00 ex VAT lucas toggle switches with black levers These require a hole 14.5mm diameter general PurPose Off-on with chrome nut. Rated at 5 amps maximum on 12v systems SPB each ex VAT windscreen washers Sprung with chrome nut. For windscreen washers etc. SPB each ex VAT 2-sPeed wipers Off-on-on. With lever 20mm long and chromed bezel. Rated at maximum on 12v systems each ex VAT Quality switches with a 'Lucas' lever and the appearance of a Lucas switch. Can be used on 6 or 12 volts (Ratings are for 12v systems). Requires hole 12mm diameter, panel thickness between the two nuts supplied up to 4.5mm 2 terminals. Rated at 15 amps each 6.45 ex VAT 4 terminals. Rated at 15 amps each ex VAT 3 terminals. Rated at each ex VAT 6 terminals. Rated at each ex VAT 52 general PurPose Off-on. With chromed bezel. Rated at on 12 volt systems. As fitted to Austin Healey Sprite Mk IV/MG Midget Mk III panel lights and wipers and MGB single speed wipers each ex VAT on-on fuel changeover Can be wired either on-on for fuel changeover, or onoff for auxiliary lamps etc. Has black lever and chrome bezel. Rated at 18 amps on 12V systems each ex VAT general PurPose Off-on, With chromed nut. Rated at maximum on 12v systems. As used on Aston Martins, 1977 to 1989, Morgan 4/ to 1985, on Minis (wipers) and on motorcycles each ex VAT Off-on-on. With chromed nut. Fitted to MGB from , Austin Healey Sprite Mk II to Mk IV, MG Midget Mk I to Mk III 1971 and Morris Oxford. Rated at on 12 volt systems each ex VAT Off-on-on, With chromed nut. Rated at maximum on 12v systems. As used on Aston Martins, 1977 to 1989, Morgan 4/ to 1985, and on motorcycles each ex VAT switches with jaguar lever Interior Light 5 amps maximum on 12 volt systems (shown left) SPB each ex VAT Windscreen, sprung, 5 amps maximum on 12 volt systems SPB each ex VAT Panel Light (shown right) each ex VAT Wiper each ex VAT Heater Fan each ex VAT Set of 6 replacement Knobs for above switches each ex VAT indicators On- with black lever and chrome nut. Rated at 10 amps maximum on 12v systems each ex VAT headlamp dip With 40 mm long lever and chrome bezel. 12 volt. For headlamp dipping. As fitted to the Jaguar E Type. Requires hole size 12mm, or can be fitted to a 14.5mm diameter hole by using Threaded Washer and Bezel or Nut (see next page). Using these parts will make the switch look like a Lucas switch each ex VAT -on 6 terminals. Rated at each ex VAT The very best in toggle switches. Approved to CECC Rated at 35 amps on 12V systems. Used by many of the top motorsport teams including Prodrive, Williams and McLaren. Alloy topped housing with polished alloy environmentally sealed lever. Hole size required is 12mm diameter 3 terminal SD/ each ex VAT on-on For fuel changeover. Rated at 15 amps each ex VAT Standard Lucas Toggle Swtches are fitted to a 14.5mm diameter hole. If you wish to replace them with either the Quality Toggle (above) or the Professional Toggle (also above) this can be done using the special parts below. In the case of the Quality they will then look just like the original Lucas switches you are replacing: special bezel (Left) Use these two parts together to make the above quality switches look like a Lucas switch: Bezel each 1.60 ex VAT Threaded Washer each 1.10 ex VAT (Both parts shown left with one of the switch) 2 terminal each ex VAT 6 terminal each ex VAT sprung For washers. Rated at each ex VAT wipers/washers Off - on - sprung on. Rated at each ex VAT 4 terminal each ex VAT fuel changeover On-on SD/ each ex VAT window motors Sprung on - off - sprung on each ex VAT special nut (Left) Use these two parts together to make the above quality switches look like a Lucas switch: Nut each 1.35 ex VAT Threaded Washer each 1.10 ex VAT (Both parts shown left with one of the switches) Professional Toggle Off-on-on SD/ each ex VAT washers Sprung SD/ each ex VAT 53

3 Toggle +44 (0) A Seven matching switches with chromed levers 50mm long and chrome bezel. Designed to be fitted through 2 terminal. Rated at 15 amps SD/ * each ex VAT toggle switches with long levers metal dash panels. 12mm hole size. Made in England to the highest standards. Ratings are for 12V systems 4 terminal. Rated at 15 amps SD/ * each ex VAT fuel changeover On-on. Rated at 15 amps SD/ each ex VAT or wipers of-on-on. Rated at / each ex VAT These three parts are applicable to the switches on the previous page stainless steel Plate For switches marked * engraved OFF-ON each 0.60 ex VAT A & B seal Kit For waterproofing all switches in boxes A and B (opposite page) each 2.10 ex VAT B only cover Kit For waterproofing all switches in box B (opposite page) each 3.41 ex VAT Switch not included switch Panel Plastic, with 13mm diameter holes for two switches, or one switch and a warning light (shown) each 1.38 ex VAT Plastic, with a 13mm diameter hole for one switch each 1.25 ex VAT led tip round lever toggle switches Toggle A panel mounted toggle switch requiring a 12mm diameter hole. Connections at the rear are by Lucar connectors. These switches are of a durable metal construction with nickel plated levers and are rated at 20 amps on 12V systems. Connect ON side to live input, OFF side to load and terminal at the top to NEGATIVE earth. LEDs give a stable light and do not generate heat windscreen washers Or flashing headlamps. Sprung. Rated at each ex VAT B 3 terminal. Rated at / each ex VAT toggle switches with stainless levers 6 terminal. Rated at / each ex VAT These are quality switches requiring hole size 12mm diameter allowing for a panel thickness between the 2 nuts supplied of up to 4.5mm. Can be used on 6v or 12v. Ratings are for 12v systems amber led When switched on the tip is illuminated by a amber LED SD/ each 6.00 ex VAT red led When switched on the tip is illuminated by a red LED SD/ each 6.00 ex VAT blue led When switched on the tip is illuminated by a blue LED SD/ each 6.00 ex VAT green led When switched on the tip is illuminated by a green LED SD/ each 6.00 ex VAT conversion to lucas appearance 2 terminals. Rated at 15 amps * 6.59 each 5.49 ex VAT 3 terminals. Rated at each ex VAT 4 terminals. Rated at 15 amps * each 8.58 ex VAT 6 terminals. Rated at each ex VAT -on 6 terminals. Rated at each 9.88 ex VAT Standard Lucas Toggle Swtches are fitted to a 14.5mm diameter hole. If you wish to replace them with any of the switches on these two pages and the previous one this can be done using the special parts below. The threaded washer reduces the Lucas hole size to suit the switches fuel changeover On-on. Rated at SD/ each ex VAT windscreen washers Or flashing headlamps. Sprung on-off. Rated at each ex VAT windscreen wipers/ washers Off - on - sprung on. Rated at each ex VAT See accessories on the next page window motors Sprung on - off - sprung on. Rated at each ex VAT special bezel Use these two parts together to fit the switches on these two pages into a 14.5mm diameter hole: Bezel each 1.60 ex VAT Threaded Washer each 1.10 ex VAT (Both parts shown with LED and Long Lever ) special nut Use these two parts together to fit the switches on these two pages into a 14.5mm diameter hole: Nut each 1.35 ex VAT Threaded Washer each 1.10 ex VAT (Both parts shown with one switch) 54 55

4 Rocker +44 (0) Rocker A range of ten Rocker with special connector sockets available to simplify installation. Rated at 6 amps on 12V systems. Cut out size 21 x 30 mm A range of deluxe rated at 30 amps on 12V systems. If you use the switches on their own the cut out size is 22mm x 44mm. If you use them with a surround the cut out is 26mm x 50mm. The surrounds fit together firmly to make a switch panel, and there is a special surround to go at each end. They are illuminated with your other panel. The connector kit makes the wiring easier. These switches make kit cars look very professional! Off 1 on 1 & 2 on rear fog wiper Off 1 on 2 on washer Push on Typical panel made up using these parts surrounds For fitting these switches together Central (left) each 5.70 ex VAT End (right) each 4.94 ex VAT blanking Plate Fits central and end surrounds each 4.70 ex VAT connector Kit Plugs into the back of switch each 4.94 ex VAT fan Off 1 on 2 on interior light demist spotlamps hazard each 9.50 ex VAT that were fitted to specific cars brake test Sprung off push on connectors For all of these switches bar each 1.95 ex VAT For hazard switch each 3.99 ex VAT Off 1 on 1 & 2 on each ex VAT Off 1 on 1 & 2 on each ex VAT fans Single speed each 7.50 ex VAT 2 Speed. Off 1 on 2 on each ex VAT rear fog each 7.50 ex VAT interior light each 7.50 ex VAT wiper on each ex VAT window lift Push on off push on each 9.50 ex VAT washer Push on each 9.50 ex VAT hazard each ex VAT heated rear window As fitted to MGB each ex VAT heater blower as fitted to Maxi Mk II each ex VAT wiper For MGB, Minis each 6.76 ex VAT spotlamps each 7.50 ex VAT lamp washers Push on each 8.40 ex VAT rear demist each 7.50 ex VAT fuel changeover On on each 8.40 ex VAT work light each 7.50 ex VAT A series of six switches that were fitted to the Jaguar E Type Series 2, V12 and XJ6 Requires hole size 16 mm x 32 mm. At the rear these switches have Lucar 6.4 mm connectors fan off - on - on For Austin each ex VAT off - on each ex VAT radio aerial Off - on -sprung on for Jaguars each ex VAT demist off - on each ex VAT Hazard Switch each ex VAT On/off Switch each ex VAT Sidelights Switch each ex VAT Switch each ex VAT Switch each ex VAT Heater Fan Switch each ex VAT 56 57

5 Knobs +44 (0) each 4.00 ex VAT each 4.95 ex VAT each 4.18 ex VAT each 6.38 ex VAT off on 9.5mm dia hole, plain knob knurled chromed bezel. Screw connections at rear. Rated at on 12V systems 31434* each ex VAT Push on-push off Panel light Push on - push off. Requires 19.5 mm diameter hole. Brown knob engraved 'P'. Mitred chrome bezel. As fitted to the Triumph Roadster of 1948/9 for panel each ex VAT each 3.75 ex VAT Push-Pull Knobs for hexagonal shafts each 4.18 ex VAT each 6.00 ex VAT off Pull on turn Pull on Supplied without knob, mitred chromed bezel, fitted to Alvis TC21, TC21/100, Morris Minor & MGA for 31126* each ex VAT -on Panel/dash Off - pull on - turn on - turn on. Hexagon shaft supplied without a knob. Chrome nut. As fitted to Rolls-Royce, Bentley and others for panel/dash. Knobs listed in this section for hexagon shafts can be used with this Switch * each ex VAT each 4.18 ex VAT each 5.45 ex VAT each 4.18 ex VAT each ex VAT off Pull on Pull on For sidelamps/ headlamps. Supplied without knob 34477* each ex VAT Knob headlamp symbol As fitted to MGB from and Triumph TR each 8.54 ex VAT Knobs for mg s mga Knob set (11 Knobs) (Right) This set of eleven Knobs is for the MGA. Nine fit hexagonal shafts - plain, F, L, P (with arrow for panel rheostat), W, C, S and two domed knobs. Plus the direction indicator knob and the blower B knob per set ex VAT starter Push Ffor TR2,TR3/TR3a each 3.90 ex VAT wiper For TR2, TR3/TR3a each 4.50 ex VAT blower For TR choke Pull For TR2,TR3/TR3a each 6.50 ex VAT overdrive Pull Knob for TR each 3.06 ex VAT air For TR Knobs set octagonal Knobs hex. shaft (5 Knobs) (Left) Made for the MG TF, this is a set of 5 octagonal knobs with letters 'A', 'C', 'L', 'P' and 'S' which fit switches with hexagonal shafts per set ex VAT Knobs for triumph cars side head For TR2,TR3/TR3a each 5.50 ex VAT choke For TR each 4.10 ex VAT interior light For TR each 5.50 ex VAT Panel For TR2, TR3/Early TR3a each 3.50 ex VAT wiper/washer For TR Panel For TR Panel For Late TR3a each 5.90 ex VAT heat For TR choke For TR5/TR These four switches have a knob that has a light which shows when switch is on. They require a 11.5mm diameter hole. Rated at 16 amps on 12 volt systems. The knob unscrews to enable the switch to be fitted green each 7.65 ex VAT red each 7.65 ex VAT amber each 7.65 ex VAT blue each 7.65 ex VAT blower For TR5/TR air direction For TR5/TR water valve For TR5/TR early tr5/tr250/tr6 Knob set One each to inclusive. Pictorial set for TR5, TR250 and TR6 up to CP50000 and CC50000 (USA models) per set ex VAT tr6 Knob set TR6 Knob Set USA models from CF1 on One each to For TR6 USA models from CF1 on per set ex VAT 58 59

6 Push Button +44 (0) Indicator With chromed cover for surface mounting on dashboard each ex VAT For metal dashboards. Chrome bezel. Lucar connectors. Rated at 11 amps on 12 volt systems. 20mm hole dia. SPB each ex VAT Flush fitting, Rated at 0.8 amps on 12 volt systems. 16mm hole diameter each ex VAT For metal dashboards. Chrome bezel. Screw Connectors. Requires 20mm diameter hole SPB each ex VAT Rated at 0.8 amps on 12V systems. 12mm hole dia each ex VAT starter switch (Left) Requires hole 22mm diameter. Negative earth only as it has a diode that lights up so that you can find it. Wire it via the ignition switch each ex VAT For metal dashboards. Chrome bezel. Screw Connectors. Requires 19mm diameter hole each ex VAT With stainless steel surround. Rated at 6 amps on 12V systems. Fits almost flush with panel. Long thread so that it can be used on metal or wood panels up to 15mm thick. 22mm dia requiring a 19mm diameter hole. Screw connections each 7.16 ex VAT Long thread for wooden dashboards (max 20mm). Chrome bezel. Screw Connectors. R e q u i r e s 1 9 m m diameter hole each ex VAT Red with chrome surround for starter solenoid. Rated at 0.8 amps on 12V systems. 17.5mm overall dia, requiring a 12mm diameter hole in the panel. Two tags for soldering wires each ex VAT Push off Integral polished bezel. 22mm hole dia each 7.00 ex VAT tps1 self cancelling switch The only dash mounted self cancelling we have available. As used by Rolls-Royce, MG (TF & MGA), Jaguar XK 140. Can also replace the earlier clockwork types. This switch self cancels pneumatically. Requires 20mm dia. hole. No warning light. Supplied without lever each ex VAT manual switch (Left) Cream colour with warning light. Mounts on face of panel SPB each ex VAT (Right) As above but black each ex VAT For strapping around the steering column. Lamp on end flashes with indicators. Does not self cancel each ex VAT lever for lucas tps1 Standard Lever for each ex VAT manual switch Requires 25mm dia. hole. (Left) Cream lever each ex VAT (Right) Black lever each ex VAT indicator/hazard warning switch For strapping around the steering column. Does not self cancel each ex VAT mga lever for lucas tps1 For tor Switch as fitted to the MGA each 5.95 ex VAT manual switch Lever is illuminated internally to act as warning light. (12 volt only). Requires 25mm dia. hole each ex VAT For strapping around the steering column. Does not self cancel Black end (plain) each ex VAT White end (plain) each ex VAT Green (illuminated) each ex VAT 60 waterproofed Waterproofed. 23mm hole diameter. Lucar connectors each 5.34 ex VAT waterproofed Waterproofed. 25mm diameter hole. Screw connectors each 4.50 ex VAT aston martin Petrol and oil gauge switch (Right) Lucas original for petrol/oil gauge on Aston Martin DB2, DB2/ each ex VAT waterproofed Red push button with brass body and nut requiring a 22mm hole through the panel which can be up to 10mm thick. Supplied with a waterproof cover each 6.95 ex VAT Push off This switch is also a circuit breaker and will automatically switch off if the circuit load exceeds 5 amps. Snaps into a hole 13.8 x 16mm in a panel between 0.8 and 1.6mm thick each ex VAT miniature Push buttons Push on - push off. Requires hole 7mm diameter. Rated at 1 amp on 12v systems. Solder tag connections. Use a relay with this switch each 3.14 ex VAT As above but push on-spring off. Red knob each 3.14 ex VAT Column mounted with green lamp on the end. As fitted to the Morris Minor each ex VAT As fitted to MGB from 1976 to 1980 Right Hand Drive models each ex VAT Mini Mk 1 Indicator switch. (can also be used on Morris 1000) with green illuminated window SD/ each ex VAT For 30mm dia columns. With headlamp flasher. Fits many cars each ex VAT As fitted to Jaguar E Type Series 1/Series 1.5 Early (shown) each ex VAT Series each ex VAT Series each ex VAT Indicator and horn push as fitted to Series 1.5 late/series 2 when collapsible steering column fitted. With fixing screws. Replaces Lucas Part No each ex VAT 61

7 Horn/Dip +44 (0) Handlebar horn button Dashboard mounting. Rated at 5 amps on 12 volt systems SPB each ex VAT horn button & dip For dashboard mounting SPB each ex VAT horn button & dip Combined Horn Button and Dip Switch as fitted to the MG TC and TD to 18882, but can be fitted to other cars each ex VAT handlebar switch right hand Lucas Original right hand Handlebar Switch for PILOT/HEAD and ENGINE OFF/RUN. For 7 8" (22 mm) diameter handlebars 189SAR each ex VAT handlebar switch Lucas Original 169SA each ex VAT horn Push Replica of Lucas chrome horn-push switch type 4a. For 7 8 handlebars each ex VAT steering wheel centre As fitted to a number of cars including the Triumph TR2 and TR3. Provides horn button and mm (4.82 inches) diameter. Rear has flange with three mounting holes. Short 52 mm (2 inches) tube at rear each ex VAT steering wheel centre As fitted to a number of cars including the Triumph TR2 and TR3. Provides horn button and mm (4.82 inches) diameter. Rear has flange with three mounting holes. Long 165 mm (6.5 inches) tube at rear each ex VAT engine cut out Switch for 7 8 handle bars each 7.95 ex VAT horn or cut-out Chromed. For 7 8 (22mm) diameter handlebars. Black button earths the contact each 9.98 ex VAT horn/cut out Black waterproof. Rubber cover over the button that earths the contact each 6.23 ex VAT Pencil for horn Push 65mm 'Pencil', part of the horn push mechanism in the centre of the steering wheel. 'Free' length 65mm. Used on many cars, including the Triumph Spitfire 1300 and 1500 up to FH and the TR4 and 4a each 7.81 ex VAT Pencil for horn Push 74mm 'Pencil', part of the horn push mechanism in the centre of the steering wheel. 'Free' length 74mm. Used on many cars, including being introduced on MGBs from chassis no in each 7.15 ex VAT Pencil for horn Push 87mm 'Pencil', part of the horn push mechanism in the centre of the steering wheel. 'Free' length 87mm. Used on many cars, including the Triumph TR each ex VAT Foot Operated Dip slip ring Slip Ring, part of the horn push mechanism in the centre of the steering wheel on MGBs introduced from chassis no in each ex VAT ducon horn/dip Reproduction by Wipac each 17.38ex VAT lucas horn/dip Reproduction of Lucas chrome Horn/Dip switch complete with wiring harness each ex VAT miller 157hv horn/dip Reproduction of Miller horn/ dip type 157HV for 7 8" (22 mm) handlebars. Complete with wiring harness each ex VAT 62 early model Reproduction of early Lucas switch. Jaguar 240 Mk II and others each ex VAT Period switch Reproduction switch each ex VAT mini switch As fitted to Mini, MG etc each ex VAT tricon horn/dip/cut out each ex VAT horn/indicator/ cut out each ex VAT 63

8 Starter +44 (0) cable operated Cable Operated as fitted to the MGTD/TF, MGA etc. Also fitted to commercial vehicles including Austin & Morris Half Ton each ex VAT floor mounted Vintage style 65mm diameter SRB each ex VAT floor mounted This is a reproduction of the period foot operated starter switch as fitted to the Willys Jeep each ex VAT Push button As in the picture each ex VAT ignition/starter/lights Off-side-head. Chrome bezel. Requires 52mm dia. hole and secures with clip. Supplied with 2 keys each ex VAT ignition/starter/lights Off-side-head appear in window. Chrome bezel. Requires 53mm dia. hole and secures with clip. Supplied with 2 keys each ex VAT ignition & starter With chrome surround and Lucar connectors. This switch has 4 positions /Off//Starter and springs back from the Starter position. Supplied with two keys. Requires 18mm diameter hole each 8.95 ex VAT ford type Starter solenoid with two terminals SRB each ex VAT starter solenoid With manual push button S each ex VAT starter solenoid With manual push button and isolated return S each ex VAT starter solenoid Universal Starter Solenoid with Lucar connectors. As fitted to many cars including MGB, Austin Healey Sprite, MG Midget, Mini and Austin 1100 Mk II/1300, MG 1300 Mk II Morris Minor 1000 and Riley 4/72 SRB each ex VAT ignition/ starter Original Lucas as fitted to MGB, with left position for auxiliary circuits, such as radio. With chrome bezel and Lucar connectors. Requires 19.6mm dia hole. Rated at 5 amps, Starter 16 amps and Auxiliary 15 amps 34680* each ex VAT Reproduction of above, Supplied with barrel and key 34680/R each ex VAT arnessignition & starter For motorcycle, but could also be used on a car dashboard. Supplied with two keys each ex VAT ignition/starter With chrome bezel & Lucar connectors. Rated at 5 amps () and 16 amps (Starter). Requires 19.6mm diameter hole /31973* each ex VAT ignition & starter switch Panel switch, starter button & red ignition warning light on aluminium panel 67mm wide x 96mm. The ignition switch has a flip-up cover which has to be lifted before the toggle switch can be switched on. Lowering this cover switches the switch off. The push starter button has a waterproof cover. Both switches are rated at 30 amps on 12V systems. The panel is marked IGNITION, ON, OFF & START and is supplied with 4 screws, wire and wiring diagram each ex VAT ignition & starter switch Panel, starter and two accessory switches on aluminium panel 112mm wide x 60mm tall. The ignition switch has a flip-up cover which has to be lifted before the toggle switch can be switched on. Lowering this cover switches the switch off. The push starter button has a waterproof cover. The panel is marked IGN, START, ACC 1 & ACC 2, and is supplied with 4 screws, wire and wiring diagram. All switches rated at 30 amps on 12V systems each ex VAT flip-up cover Spare part for switch panels or can be used with other toggle switches having metal levers each 4.99 ex VAT ignition/steering lock As fitted to MGB from and MG Midget Mk III from 1972 onwards and * each ex VAT ignition & starter (Right) As fitted to Austin A40 Countryman, , Austin Healey Sprite 31270* each ex VAT ignition Switch only. With chrome nut bezel and Lucar connectors. Rated at 17.5 amps on 12V systems. Requires hole 19.6mm diameter 30608* each ex VAT 1 2 ignition/starter 3-position Switch for Jaguar E Type Series 1, 420 & Daimlers. With chrome nut bezel and Lucar connectors. Requires hole 19.6mm dia * each ex VAT switch Knobs Suits onleft Ref each 6.12 ex VAT Ref each 7.30 ex VAT 64 ignition/ switch - military type (Right) Military type combined and Switch. Flange mounting. Supplied without Barrel & Key Assembly which you should order separately if required each ex VAT barrel & Key assembly Fits all switches marked* each 8.40 ex VAT Key Reproduction key /R 1.80 each 1.50 ex VAT Key Reproduction spade type key for Lucas switch PRS /R 1.80 each 1.50 ex VAT 65

9 Rotary +44 (0) Rotary off dimmer Suitable for panel ohms. 14.5mm dia. hole. Supplied without knob but with chrome bezel each ex VAT low/off/high miller replica Suitable for Vincent, Velocette, Rudge and some Royal Enfield models each ex VAT Panel/dash switch Off-on-on & dimmer for panel/dash on Vauxhall Cresta. Requires 10mm diameter hole. Supplied without knob or bezel each ex VAT interior switch Off-on. Interior Light Switch with bezel for Rover P6. Requires 14.5mm diameter hole. Supplied without knob each ex VAT on-off switch Quality reproduction. Requires 19mm diameter hole. Bezel is 22mm diameter. Suitable for fitting to a metal dash. Originally fitted to Rover 60 & Triumph, Norton, BSA each ex VAT switch switch for motorcycles each ex VAT switch Reproduction of the original Lucas switch U39 on motorcycles. Used on most models with DC magneto ignition. Fits 42.5mm diameter hole. Overall diameter 49.5mm each ex VAT Panel light switch As fitted to MG TD from chassis no each ex VAT wiper Knob Fits to round shaft and secures with a screw each 6.00 ex VAT large Knurled Knob For Lucas switches with hexagonal shafts. Length 25mm. Head diameter 28mm each ex VAT Accessory switch 88sa Reproduction Switch for motorcycle freestanding headlamps. Supplied complete with knob 34289/R each ex VAT socket for switch 88sa For Switch 88SA each ex VAT spare Knob for switch 88sa /R 6.30 each 5.25 ex VAT hazard warning switch Kit Right) If your car has flashers but no hazard warning facility this kit provides everything you need to add this very desirable safety feature to your car. It includes both the switch and the flasher unit and comes with full fitting and wiring instructions. There is a warning light in the knob which is illuminated when on. It comes with a bracket for under dash mounting, but can also be mounted direct to a metal dashboard. instructions are on our website SFB each ex VAT ignition switch 88sa Reproduction of Switch 88SA for motorcycle freestanding headlamps 34427/R each ex VAT socket for ignition switch 88sa For Switch 88SA each ex VAT spare Knob for ignition switch 88sa /R 6.30 each 5.25 ex VAT switch 12 volt. Small Interior Light Switch each ex VAT switch Plate Plate for each 3.51 ex VAT gearbox switch Lucas original. Fits Rover SD1 and Morgan 5 Speed Gearbox each ex VAT 66 austin gipsy switch Off-on with bezel. In the on position it makes three separate circuits. As fitted to the Austin Gipsy. Requires 14.5mm diameter hole. Supplied without knob each ex VAT changeover switch On-on. Used as fuel changeover switch on Jaguar Mk VII, VIII, VIII and IX. Requires 14.5mm diameter hole. Sorry we don t have the knob each ex VAT switch Off-on-on-on for. Supplied with lever and nut as shown. Suitable for fitting to a metal panel, requiring a hole 25.4mm diameter (1 in). Screw type terminals at rear each ex VAT Courtesy Light (Left) Fits into the door shut to operate the interior light as you open the door. The red plastic plunger is 25mm long but can be cut to reduce its length if required each 5.31 ex VAT (Right) Similar, as fitted to Triumph TR each 5.60 ex VAT 67

10 Brake Light +44 (0) low oil Pressure warning light switches 68 mechanical Pull type Flange mounted. Supplied with spring and hook each 9.99 ex VAT hydraulic brake light switch 3 8 UNF with 24 t.p.i. shown each ex VAT 1 8 NPT as used on MGA each ex VAT stop lamp switch Lucas replica. Fits BSA, Triumph Triples, Norton Commando and Triumph 750 twins 34815/R 9.66 each 8.05 ex VAT mechanical Pull type Quality reproduction of the original Lucas brake light switch. Flange mounted, with brass screw terminals each ex VAT hydraulic brake light switch Thread is 3 8 in UNF, 24 t.p.i. For Aston Martin DB5 & DB6 and BMC 180 J4, 190 J4 & 200 J4 van and Pick Up. Will also fit Triumph T140, Commando each ex VAT mechanical Pull type Reproduction of Lucas pullon style switch which was used on many 1960s motorcycles /R each ex VAT Wiper Motor wiper/washer switch As fitted to MGB from 1976 to 1980 Right Hand Drive models each ex VAT stop lamp switch Universal stop lamp switch. Replaces Wipac S each 5.63 ex VAT clip fitting for lucas motor (Right) The Lucas 14W Wiper Motor takes this clip on parking switch. (However, does not fit other Lucas motors). As fitted to the MGB from 1967, Sprite/Midget with late 1275 engines and all 1500 engines, Triumph Spitfire from about each ex VAT mechanical Pull type Lucas Original. Actuated by cable from the brake pedal and with Lucar connectors each ex VAT handbrake switch Mechanically operated Handbrake Switch 1 4 UNF thread 19 mm ( 3 4 long). Originally fitted to Jaguar E Type, Jaguar Mk II, 420, 420S, Daimler V8 and Lotus. Also used to operate the choke warning light on the Jaguar E Type 4.2 litres each ex VAT stop lamp switch Replica of Miller 43E stop lamp switch. Used on many 1950 s machines / each 7.38 ex VAT 20 P.s.i. on when oil pressure drops below 20 p.s.i.. Diameter 27mm with 1 8 in NPTF thread each ex VAT overdrive switch As fitted in gear lever knob on Triumph Stag, Spitfire, GT each ex VAT Cap for overdrive switch each 7.25 ex VAT overdrive switch A good quality reproduction of the Switch fitted to the Triumph TR2 from TS6267 and TR3. Lucas original Part No. was each ex VAT overdrive solenoid For Austin Healey each ex VAT adjustable 0 16 P.s.i. on when oil pressure drops below the set figure which can be adjusted between 0 and 1.1 bar (16 p.s.i.). Diameter 26mm with 1 8 in NPTF thread each ex VAT overdrive solenoid For Jaguar each ex VAT adjustable P.s.i. on when oil pressure drops below the set figure which can be adjusted between 15 and 50 p.s.i.). With 1 8 in NPTF thread each ex VAT Overdrive & Solenoids overdrive inhibitor switch Changeover between two opposite pairs of Lucar contacts. Requires 11mm diameter hole each ex VAT overdrive switch For the Triumph TR4, TR4a and TR6 Right Hand Drive each ex VAT Left Hand Drive each ex VAT overdrive solenoid For MGB each ex VAT 69