ESA II. I - Revive Slider Conversion Kit. Installation instructions

Size: px
Start display at page:

Download "ESA II. I - Revive Slider Conversion Kit. Installation instructions"

Transcription

1 ESA II I - Revive Slider Conversion Kit Installation instructions DL EN

2 dormakaba ESA II I-Revive Slider Conversion Kit Table of Contents Table of contents Table of contents General information Product description. ESA II slider conversion kit components. Additional standard kit components. Optional components 5 Standard conversion kit contents. Standard conversion kit contents Remove all hardware from header 8. Identify devices wired to existing controller 8. Disconnect 5 VAC wiring to existing controller 8. Disconnect all wiring and remove all hardware from header 8. Door carrier bar belt brackets 8 5 Backplate component layout 9 5. Backplate components 9 Install backplate assembly in header 0. Modify header T-slot height 0. 5 VAC wiring termination location 0. Insert T-nuts into header T-slot 0. Install backplate into header Install return pulley assembly in header. Install return pulley assembly in header 8 Install belt 8. Route belt around motor gearhead pulley 8. Route belt around standard return pulley 8. Route belt around return pulley, standard lock, bi-stable assembly (option) 9 Belt connection bracket, ends of belt 5 9. Fasten ends of belt to belt connection bracket 5 0 Tension belt 0. Tension belt using tension adjustment at return pulley Stanley door installation, chapters - Front of belt connection to door. Fasten carrier bar belt bracket to belt connection bracket. Fasten carrier bar belt bracket to door carrier bar Rear of belt bracket connection to belt 8. Fasten belt connection bracket to rear of belt, RH bi-part door 8. Fasten carrier bar belt bracket to belt connection bracket 8 Rear of belt connection to RH door 9. Fasten carrier bar bracket to RH door carrier bar 9 5 Horton door installation, chapters Bottom of belt connection to door. Fasten bottom belt connection bracket to carrier bar belt bracket Belt connection bracket, top of belt. Fasten belt connection bracket to top of belt, LH bi-part door 8 Top of belt connection to LH bi-part door 8. Fasten top of belt connection bracket to LH carrier bar belt bracket 9 Header and sensor wiring 9. Connect existing control wiring to ESA II controller 9. Connect 5 VAC wiring 9. Header grounding 9. BEA IXIO-DT activation and presence sensors 0 Initial startup and programming 5 0. Door signage 5 0. Commissioning 5

3 dormakaba ESA II I-Revive Slider Conversion Kit Chapter General information. ESA II I-Revive Slider Conversion Kit installation. This manual provides an example of the installation steps required to install the I-Revive Slider Conversion Kit into an existing sliding door system. NOTICE Modification of steps documented in this manual may be required due to configuration of manufacturer's sliding door installation. Pictures and diagrams shown in this manual are representative of an installation of the ESA II I-Revive Slider Conversion Kit. Each sliding door installation may require different component locations, orientations or mounting methods.. Symbols used in these instructions. WARNING This symbol warns of hazards which could result in personal injury or threat to health. CAUTION This symbol warns of a potentially unsafe procedure or situation. NOTICE Draws attention to important information presented in this document. WARNING Check all mechanical components of the door system and replace any components not in satisfactory condition due to wear or other issues. TIPS AND RECOMMENDATIONS Clarifies instructions or other information presented in this document. TIPS AND RECOMMENDATIONS Initial startup and programming of the ESA II controller is contained in the ESA II Controller Commissioning, Troubleshooting, and Maintenance manual, see Chapter 0.. Dimensions Unless otherwise specified, all dimensions are given in both inches ( ) and millimeters [mm].. Abbreviations LH, Left hand RH, Right hand ESA II DL

4 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Product description. ESA II slider conversion kit components Backplate ESA II controller Motor gearbox DC power supply Return pulley assembly Belt tensioner Return pulley Belt Fastener packs, belt and carrier bar brackets Fig... Backplate assembly 5 Fig... Return pulley Fig... Belt Fig... Fastener packs.. I - Revive slider conversion kit DC Backplate assembly. Return pulley and belt tension assembly Fig... shows return pulley assembly as shipped, with tension adjustment on right hand side of assembly. Specific installations may require tension adjustment location on left hand side of assembly. This requires relocation of tension assembly along with installation of long tension adjustment bolt, see Chapter.. Belt. Fastener packs. Additional standard kit components Decal quantity Decal, double sided quantity Decal quantity Decal quantity BEA IXIO - DT quantity Hole plug kit quantity ESA II Commissioning, Troubleshooting and Maintenance manual ESA II I-Revive Slider Conversion Kit Owner's manual Fig... ESA safety label kit Fig... BEA IXIO-DT Fig... Hole plug kit Fig... Manuals.. ESA safety label kit DK-00, Safety label kit, pair.. Activation & safety sensor DX-0 BEA IXIO - DT.. Hole plug kit DC Manuals. ESA II Controller Commissioning, Troubleshooting and Maintenance manual DL8-00. ESA II I-Revive Slider Conversion Kit Owner's manual DL8-00 ESA II DL

5 dormakaba ESA II I-Revive Slider Conversion Kit Chapter. Optional components I-Revive standard lock, bi-stable Return pulley Fig... I-Revive standard lock, bistable.. I-Revive standard lock, bistable DC58-00 Refer to ESA II Commissioning, Maintenance and Troubleshooting manual, Section -D for parameter setup. ESA expansion module Expansion module cable Fig... ESA expansion module and cable.. ESA II expansion module with cable DX Refer to ESA II Commissioning, Maintenance and Troubleshooting manual, Section 0 for installation and Sections and for wiring. Battery backup assembly 0 amp blade and fuse holder 0 foot cable V. AH battery 5 Bracket Key switch panel Fig... ESA II battery backup assembly 5 Fig... Key switch panel assembly.. ESA II battery backup DS Rechargeable battery pack with 0 ft [ meter] cable. Refer to ESA II Commissioning, Maintenance and Troubleshooting manual, Section G through K for functional test... Key switch panel DX8 ESA II DL

6 dormakaba ESA II I-Revive Slider Convesion Kit Chapter Standard conversion kit contents. Standard conversion kit contents Box containing conversion kit. Backplate assembly. Box containing 5 VAC wiring and plug for DC power supply. Fastening hardware packs. ESA II rechargeable battery pack (option).5 Return pully and belt tension adjustment assembly. Special T-bolt and nut. Belt Box containing belt.. Boxes containing kit hardware Fig... Kit shipping boxes Kit boxes and content will differ based on order... Kit contents removed from shipping boxes Fig... Kit contents removed from shipping boxes.... Fig... Kit shipping boxes opened Backplate.. DC power supply.. Motor gearbox.. ESA II controller.. 5 VAC cable.. 5 VAC plug for DC power supply... Fastening hardware packs.. ESA II rechargeable battery pack (option).. Fastening hardware.5. Return pully and belt tension adjustment.5. Short tension adjusment bolt. Special T-bolt & nut. Belt.. Kit hardware removed from all boxes Fig... Kit contents removed from all boxes ESA II DL

7 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Pack 0 /" x /" SHCS Pack 0 /" x /" SHCS Pack 8 mm flat washer Pack Belt connection bracket parts 5 Pack 0 /" x 5/8" SHCS Pack 0 T-nut Pack 05 Carrier bar belt bracket 8 Pack 0 /" locking nut 9 Pack 0 5/" x /" HHCS.. Fastening hardware pack numbers Fig...5 Fastening hardware packs and pack numbers Fastening pack hardware views Fig... Pack 0 Fig... Pack 0 Fig...8 Pack Fig...9 Pack Fig...0 Pack 0 Fig... Pack 0 Fig... Pack 05 Fig... Pack 0 0 Special T-bolt and nut /" hole plug /8" hole plug /" hole plug Fig... Pack 0 Fig...5 T-bolt & nut 0 Fig... DC0858 Hole plug kit.. Fastening pack hardware quantities and descriptions Pack number Part quantities Horton Stanley Pack Pack description Reference chapter Pack number Part quantities Horton Stanley Pack Pack description Reference chapter 8 mm flat washer,,,, 0 T-nut, Belt connection bracket parts 9,,,, 05 Carrier bar belt bracket,,, 0 SHCS, / x /",, 0 0 SHCS, / x /" N/A 0 Locking nut,, 0 0 HHCS, 5/ x /",, 0 0 SHCS, / x 5/8", --- Special T-bolt & nut Fig...5 ESA II DL

8 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Remove all hardware from header. Identify devices wired to existing controller.. Devices and wiring connections. Document devices wired to controller: Functions (security contacts, mag locks, etc.). Wire colors and connections to controller terminals (DC, signal)... Existing activation and presence sensors. IXIO-DTI presence and activation sensors and wiring provided with this kit (Para..) will replace any existing activation and presense sensors and wiring, disconnect and discard this sensor wiring... Door beam sensors. Document any beam sensor wiring... Floor mat wiring. Document any floor mat wiring.. Disconnect 5 VAC wiring to existing controller.. 5 VAC power to controller. Locate customer circuit breaker supplying 5 VAC power to controller.. Turn circuit breaker OFF... Disconnect 5 VAC wiring from controller.. Disconnect 5 VAC wiring from controller.. Install wire nuts or electrical black tape on ends of 5 VAC wiring.. If circuit breaker number and location not identified in header, affix label or tag with this information. TIPS AND RECOMMENDATIONS Insure all wiring connections to existing controller are fully documented! WARNING 5 VAC power wiring will be removed from existing controller (Para...). Electric shock hazard if circuit breaker not turned OFF!. Disconnect all wiring and remove all hardware from header.. Disconnect all wiring to controller.. Disconnect all wiring to existing controller referenced in Para.., including on/off/hold open switch wiring. Discard "power" switch wiring. Do not remove on/off/hold open switches.. Insure functions of all wiring are labeled.. Door carrier bar belt brackets.. Carrier bar belt brackets attached to door. Stanley doors, remove existing carrier bar belt brackets attached to doors (Chapter ). Brackets will be replaced with brackets in Fastener pack 05. Horton doors, leave existing carrier bar belt brackets attached to doors... Remove all hardware from header.. Remove hardware from header (controller, motor, gearbox, pulleys, belts, brackets).. Do not remove any physical door hardstops. 8 ESA II DL

9 dormakaba ESA II I-Revive Slider Conversion Kit Chapter 5 5 Backplate component layout 5. Backplate components DC power supply. Motor gearbox. Motor gearbox pulley ESA II controller Backplate DC power supply. Motor gearbox. Motor gearbox pulley ESA II controller. ESA Expansion module (option) Backplate Fig. 5.. Fig. 5.. Backplate components. Backplate component layouts 5.. Backplate components. Components installed on backplate are shown in Fig Service Interface 5.. Backplate location and layout The manufacturer's sliding door installation may determine:. Backplate location in header.. Backplate component layout.. Motor gearbox orientation; pulley must be in line with belt.. DC power supply should be located at one side of backplate. Seven to eight inches of space between power supply and edge of header is required for installation and removal of 5 VAC plug and cable. TIPS AND RECOMMENDATIONS For top of header installation, ESA II controller must be mounted on backplate so that terminal connections and labeling face outward. () slots for header mounting fasteners. () M5 x 0.8 holes for component mounting Fig. 5.. Backplate detail 5 5/ [89] ESA II DL

10 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Install backplate assembly in header. Modify header T-slot height T-slot height modification T-nut (Pack 0) Header Horton T-slot Fig... Header T-slot height modification Fig... Horton T-slot.. Existing header T-bolts Move exiting header T-bolts to right and left hand ends of header... Increase height of header T-slot.. Increase height of T-slot in a location near one side of header. Recommended tool: /8" to -/8" Unibit. Horton headers use top T-slot for mounting backplate and return pulley assemblies (Fig...), see Chapter 5. TIPS AND RECOMMENDATIONS Expansion of T-slot height is necessary to install T-nuts (Fig...).. 5 VAC wiring termination location. Insert T-nuts into header T-slot.. Header 5 VAC wiring location.. 5 VAC wiring will terminate at backplate DC power supply location (Fig... as an example).. If required, extend existing 5 VAC wiring to DC power supply location before proceding. Backplate slot for T-bolt (Fig...). Backplate slot. Backplate slot. Backplate slot Backplate Header T-slot 5 DC power supply Pack 0 T-nuts Special T-bolt and nut Fig... Backplate slots for T-nut locations 5... Fig... Header T-slot Fig... Pack 0 Fig... T-bolt, nut TIPS AND RECOMMENDATIONS Backplate component layout may differ from Fig Insert T-nuts for backplate mounting.. Insert () T-nuts (Fig...) into header T-Slot at height modification location (Fig...).. Position T-nuts at backplate assembly location in header (Para..). 0 ESA II DL

11 dormakaba ESA II I-Revive Slider Conversion Kit Chapter. Install backplate into header Backplate slot. Backplate slot. Backplate slot. Backplate slot (not shown) Backplate Pack 0 T-nuts Special T-bolt and nut DC power supply Backplate slot next to DC power supply 5 VAC connection Special T-bolt 5 Backplate ground wire 5 VAC receptacle Fig... Backplate T-nut locations in header... Fig... Pack 0 Fig... T-bolt, nut Fig... T-bolt in backplate slot 5.. Place backplate assembly (Chapter 5) into header.. Place backplate assembly into header. CAUTION Seven to eight inches of space next to DC power supply 5 VAC receptacle (Fig....) is required for installing and removing 5 VAC plug (Fig..5) and wiring.. Position installed T-nuts (Para...) in approximate backplate T slot locations.,., and. (Fig...)... Install backplate over special T-bolt. Special T-bolt (Fig...) will be used as a ground connection.. Insert special T-bolt in header T-slot next to DC power supply (Fig..).. Install backplate slot next to DC power supply 5 VAC connection (Fig...) over special T-bolt.. Place backplate ground wire lug over special T-bolt.. Thread nut (Fig...5) onto special T-bolt but do not fully tighten. DC power supply Backplate slot next to DC power supply. 5 VAC connection T bolt nut 5 Backplate ground wire 5 VAC plug Fig...5 T-slot bolt nut 5 ESA II DL

12 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Pack 8 mm flat washer Pack 0 / x /" SHCS (Horton) Pack 0 / x 5/8" SHCS (Stanley) Pack 0, T-nut Backplate slot 5 5/" T-handle hex key Pack 8 mm flat washer Pack 0 / x /" SHCS (Horton) Pack 0 / x 5/8" SHCS Pack 0 T-nuts Fig... Securing backplate slot 5 Fig... Pack Fig...8 Pack 0 Fig...9 Pack 0 Fig...0 Pack 0.. Install SHCSs into T-nuts.. Align the three T-nuts in header T-slot behind backplate slots (Fig...) before proceding with step.. Place 8 mm flat washer onto SHCS ().. Using 5/ T-handle hex key, thread SHCS () into T-nut. Do not tighten. LH backplate slot shown as reference.. Repeat for remaining two SHSCs. ESA II controller Pack 0 / x /" SHCS (Horton) Pack 0 / x 5/8" SHCS (Stanley) Nut Backplate slot Bottom of backplate Bottom of header T-slot 8 DC power supply Fig... Backplate flush with header T-slot Fig... Backplate flush with header T-slot.. Align backplate flush with header T-slot and tighten SHCSs (Stanley).. Lift backplate until bottom of backplate is flush with bottom of header T-slot.. Tighten () SHCS at ESA II controller backplate slots. Check for flush surfaces between bottom of backplate and bottom of header T-slot.. Tighten SHCS at DC power supply.. Check for flush surfaces between bottom of backplate and bottom of header T-slot...5 Tighten nut on special T-bolt. 5. Tighten nut () at DC power supply. 8.. Backplate mounted on top of header (Horton).. Position backplate on top of header as shown in Chapter, Fig..... Insure backplate is parallel to header.. Tighten three SHCS and nut on special T-bolt. ESA II DL

13 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Install return pulley assembly in header. Install return pulley assembly in header Return pulley assembly Return pulley Tension adjustment, long bolt slots for mounting assembly to header 5 Tension adjustment, short bolt Fig... Return pulley tension adjustment, short bolt. 5 Fig... Return pulley tension adjustment, long bolt. NOTICE If installing return pulley with I-Revive standard lock, bi-stable option (Fig. 8..), belt must be routed around return pulley before installing assembly in header. Go to Para Insert T-nuts into header T-slot. Insert three T-nuts (Pack 0) into header T-slot height modification (Para..)... Place return pulley assembly in header. Place return pulley assembly into header. Mounting slots Belt tension adjustment bolt Header T-slot 8 Pack, 8 mm flat washer Pack 0, T-nut Pack 0, /" x 5/8" SHCS (Stanley) Pack 0, /" x /" SHCS (Horton) Belt tension adjustment bolt 5 SHCS with flat washer Flush surface at header T-slot and return pulley assemlby Fig... Fasten return pulley assembly to header 8 Fig... Return pulley assembly installed in header 5 5 TIPS AND RECOMMENDATIONS A minimum of four inches of space must be provided for adjustment of belt tension adjustment bolt... Fasten assembly to header.. Slide T-nuts into position behind return pulley assembly mounting slots.. Place 8 mm flat washer (Pack ) onto SHCS (8).. Using 5/" T-handle hex key, thread SHCS (8) into T-nut behind slot, do not tighten.. Repeat steps and at remaining two slots... Return pulley bracket flush with bottom of header T-slot (Stanley).. Lift return pulley assembly until bottom of bracket is flush with bottom of header T-slot.. Tighten the three SHCSs.. Check for flush surface of bottom of return pulley bracket and bottom of header T-slot...5 Return pulley mounted on top of header (Horton).. Position return pulley on top of header as shown in Chapter 8, Fig Insure return pulley is parallel to header.. Tighten three SHCS. ESA II DL

14 dormakaba ESA II I-Revive Slider Conversion Kit Chapter 8 8 Install belt 8. Route belt around motor gearhead pulley 9 Belt Fig. 8.. Belt 9 TIPS AND RECOMMENDATIONS Motor gearhead position and location may be different than shown in Fig. 8.. Rear of belt Front of belt Motor gearhead Pulley Fig. 8.. Belt at motor gearhead 8.. Route belt around motor gearhead pulley.. Place belt around pulley at motor gearhead.. Carry one belt end to return pulley location in header. CAUTION Insure belt is not twisted between the two pulleys!. Carry other belt end to center of header. 8. Route belt around standard return pulley Fig. 8.. Belt at return pulley assembly Rear of belt Front of belt 5 Return pulley TIPS AND RECOMMENDATIONS Return pulley configuration, position and location may be different than shown in Fig Route belt around return pulley.. Route belt end from gearmotor pulley around return pulley.. Carry belt end to center of header. 8. Route belt around return pulley, standard lock, bi-stable assembly (option) 5 Return pulley Belt retainer Hex screw 8 Bistable lock (not shown) Fig. 8.. I-Revive standard lock, bi-stable assembly Route belt around return pulley. Orient assembly as shown in Fig Loosen () hex screws with a mm T-hande hex key and remove belt retainer.. Route belt from motor gearhead around pulley.. Reinstall belt retainer and secure with the two hex screws. 8.. Install assembly in header, go to Para After assembly is installed in header carry belt to middle of header. ESA II DL

15 dormakaba ESA II I-Revive Slider Conversion Kit Chapter 9 9 Belt connection bracket, ends of belt 9. Fasten ends of belt to belt connection bracket Belt Belt clamping plate. Clamping plate tab Pack Belt connection bracket. Bracket slot for clamping plate tab Spring clip Fig.9.. Belt clamping plate and connection bracket. Fig.9.. Moving clamping plate toward belt Fig.9.. Spring clip installed, view of bracket reversed to show spring clip. Fig.9.. Belt teeth fully inserted in clamping plate 9.. Secure belt ends in belt connection bracket. TIPS AND RECOMMENDATIONS This procedure secures belt ends to belt connection bracket. If a bi-part door, Chapter or documents installation of second belt connection bracket. TIPS AND RECOMMENDATIONS Bracket orientation and belt may differ based on installation.. Place belt end surfaces against belt connection bracket, with belt ends against each other (Fig. 9..). CAUTION Insure belt is not twisted between the two pulleys!. Insert three tabs in belt clamping plate () into corresponding slots in belt connection bracket ().. Press four belt teeth at each end of belt into slots in belt clamping plate.. Press clamping plate against belt connection bracket until belt teeth are fully inserted in clamping plate slots and clamping plate is parallel to belt connection bracket surface (Fig. 9..). 9.. Install spring clip.. Press spring clip () over belt connection bracket and belt clamping plate until fully inserted as shown in Fig ESA II DL

16 dormakaba ESA II I-Revive Slider Conversion Kit Chapters 0 and 0 Tension belt 0. Tension belt using tension adjustment at return pulley Belt tension adjustment, long bolt Return pulley 5 Belt tension adjustment, short bolt Fig.0.. Tension adjustment bolt 0.. Tension belt.. Use 0 mm wrench or socket to adjust tension adjustment bolt on return pulley assembly (Optional standard lock, bi-stable assembly shown).. Adjust belt tension to obtain: Belt deflection at center of belt of /" to /8" when squeezing front and rear of belts together with moderate effort. 5 Front of belt Rear of belt Front of belt, belt connection bracket Fig.0.. Belt tensioned Stanley door installation, chapters - Front of belt. Belt connection bracket, front of belt. Belt connection bracket, rear of belt. Carrier bar belt bracket, single or LH bi-part door. Carrier bar belt bracket, RH bi-part door Door carrier bar, Single or LH bi-part door 9 Door carrier bar, RH bi-part door 0 Anti-riser wheel Load wheel Fig.. Door carrier bars, belt connection and carrier bar belt brackets Stanley door installation Chapters through document connecting header belt connection brackets to carrier bar belt brackets Reference installation chapters Chapter, Front of belt connection to single or LH bi-part door. Chapter, Fasten belt connection bracket to rear of belt, RH bi-part door. Chapter, Rear of belt connection to RH bi-part door. ESA II DL

17 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Front of belt connection to door. Fasten carrier bar belt bracket to belt connection bracket Front of belt Belt clamping plate Belt connection bracket Belt spring clip 5 Pack 0 5/" x /" HHCS Pack 0 /" x /" SHCS Pack 8 mm flat washer 8 Pack 0 /" locking nut 9 Pack 0 T-nut 0 Pack 0 / x 5/8" SHCS Pack 05 Carrier bar belt bracket Return pulley assembly, Chapter Door carrier bar Rear of belt 0 Anti-riser wheel Load wheel Carrier bar mounting hole centerlines Fig... Front of belt bracket assembly Carrier bar belt bracket fastening to front of belt. Refer to Fig... for bracket orientation.. Fasten carrier bar belt bracket () to belt connection bracket () using: () /" x /" SHCS () () 8 mm flat washer () () /" locking nut (8). Do not tighten locking nuts.. Fasten carrier bar belt bracket to door carrier bar Fig... Carrier bar bracket fastened to carrier bar Fig... Front of belt bracket assembly to carrier bar CAUTION Check that all fasteners have been tightened... Close door or bi-part doors... Position carrier bar belt bracket.. Move front of belt until the two carrier bar belt bracket slots are on centerline of existing carrier bar bracket mounting holes (Fig..)... Determine carrier bar mounting hole locations for carrier bar belt bracket. Option : Existing carrier bar mounting holes line up with horizontal slots in carrier bar belt bracket; go to Para.... Option : New mounting holes in carrier bar are required for carrier bar belt bracket.. Insure carrier bar belt bracket horizontal slots are on centerline of existing carrier bar mounting holes (Fig...).. Using the horizontal slots, mark location for two new holes in carrier bar.. Drill two holes in carrier bar using No. drill.. Tap holes with /-0 tap... Fasten carrier bar belt bracket.. Fasten carrier bar belt bracket to carrier bar with () 5/" x /" HHCS (Pack 0)...5 Adjust belt connection bracket.. Adjust front-to-back position of belt connection bracket on carrier bar belt bracket so that front of belt is straight (Fig. 0..,..), then tighten the two /" x /" SHCSs ()... Check door and installed components.. Slowly move door through full range of travel and check: Belt does not "walk" on pulleys. Alignment of all installed components. Freedom of door movement. Belt brackets do not contact ESA II controller. ESA II DL

18 dormakaba I-Revive Slider Conversion Kit Chapter Rear of belt bracket connection to belt. Fasten belt connection bracket to rear of belt, RH bi-part door Front of belt Belt clamping plate Belt connection bracket Belt spring clip 5 Pack 0 5/" x /" HHCS Pack 0 /" x /" SHCS Pack 8 mm flat washer 8 Pack 0 /" locking nut 9 Pack 0, T-nut 0 Pack 0 /" x 5/8" SHCS Pack 05 Carrier bar belt bracket Rear of belt 9 RH door carrier bar 0 Anti-riser wheel Load wheel Carrier bar mounting hole centerlines Fig... Belt bracket assembly, rear of belt.. Locate position of belt connection bracket on rear of belt.. LH door carrier bar bracket must be fastened to LH door carrier bar (Para..).. Close bi-part doors.. Temporarily fasten belt connection bracket to carrier bar belt bracket (Fig...).. Place belt connection bracket on top of rear of belt with carrier bar belt bracket over the door carrier bar. 5. Align horizontal slots in carrier bar belt bracket with centerline of existing mounting holes () in RH door carrier bar (Fig...).. Mark both belt connection bracket edge locations on rear of belt.. Separate belt connection and carrier bar belt brackets. 5 8 Fig... RH bi-part door carrier bar 0.. Secure belt connection bracket to rear of belt. Refer to Para. 9. for pictures of assembly procedure.. Align belt connection bracket with marked bracket edge locations on rear of belt (Para...).. Insert three tabs in belt clamping plate () into corresponding slots in belt connection bracket ().. Press eight teeth of belt into slots in belt clamping plate ().. Press clamping plate against belt connection bracket until belt teeth are fully inserted in clamping plate slots and clamping plate is parallel to belt connection bracket surface... Install belt spring clip.. Press belt spring clip () over ends of belt connection bracket and belt clamping plate until fully inserted as shown in Fig Fasten carrier bar belt bracket to belt connection bracket.. Carrier bar bracket fastening to belt connection bracket. Refer to Fig... for bracket orientation.. Fasten carrier bar belt bracket () to belt connection bracket () using: () /" x /" SHCS () () 8 mm flat washer () () /" locking nut (8). Do not tighten locking nuts. 8 ESA II DL

19 dormakaba I-Revive Slider Conversion Kit Chapter Rear of belt connection to RH door. Fasten carrier bar bracket to RH door carrier bar Front of belt Belt connection bracket Belt spring clip 5 Pack 0 5/" x /" HHCS Pack 0 /" x /" SHCS Pack 8 mm flat washer 8 Pack 0 /" locking nut 9 Pack 0, T-nut 0 Pack 0 /" x 5/8" SHCS Pack 05 Carrier bar belt bracket Carrier bar Rear of belt 5 Backplate assembly 9 RH door carrier bar 0 Anti-riser wheel Load wheel Carrier bar mounting hole centerlines Fig... Carrier bar bracket fastened to carrier bar 0 Fig... Rear of belt bracket assembly to carrier bar Close bi-part doors... Determine RH door carrier bar mounting hole locations for carrier bar belt bracket. Option : Existing carrier bar mounting holes line up with horizontal slots in carrier bar belt bracket; go to Para.... Option : New mounting holes in carrier bar are required for carrier bar belt bracket.. Insure carrier bar belt bracket horizontal slots are on centerline of existing carrier bar mounting holes (Fig...).. Using the horizontal slots, mark location for two new holes in carrier bar.. Drill two holes in carrier bar using No. drill.. Tap holes with /-0 tap... Fasten carrier bar belt bracket.. Fasten carrier bar belt bracket to carrier bar with () 5/" x /" HHCS (Pack 0). Adjust lateral position of bracket so that the bracket assembly is perpendicular to the rear of belt then tighten HHCSs... Adjust belt connection bracket.. Adjust front-to-back position of belt connection bracket on carrier bar belt bracket so that rear of belt is straight (Fig. 0..,..), then tighten the two /" x /" SHCSs ()...5 Check doors and installed components.. Slowly move doors through full range of travel and check: Alignment of all installed components. Belt does not "walk" on pulleys. Freedom of door movement. Belt brackets do not contact ESA II controller. CAUTION Check that all fasteners have been tightened. ESA II DL

20 dormakaba ESA II I-Revive Slider Conversion Kit Chapter 5 5 Horton door installation, chapters 5-8 Top of belt. Belt connection bracket, top of belt. Belt connection bracket, bottom of belt. Carrier bar belt bracket, single or RH bi-part door. Carrier bar belt bracket, LH bi-part door Bottom of belt 0 Anti-riser wheel Load wheel Horton header Fig.5.. Belt connection and carrier bar belt brackets Horton door installation Chapters through 8 document belt connection bracket connections to belts and to carrier bar belt brackets. TIPS AND RECOMMENDATIONS Bottom of belt will attach to belt connection bracket for: Single door Right hand bi-part door Top of belt will attach to belt connection bracket for left hand bi-part door. 5.. Reference installation chapters Chapter, bottom of belt connection to single or RH bi-part door. Chapter, fasten belt connection bracket to top of belt for LH bi-part door. Chapter 8, top of belt connection to LH bi-part door. CAUTION Doors as installed: verify top of belt and bottom of belt connections to doors match assignments in Para Fig.5.. Horton header 0 ESA II DL

21 dormakaba I-Revive Slider Conversion Kit Chapter Bottom of belt connection to door. Fasten bottom belt connection bracket to carrier bar belt bracket Top of belt Belt clamping plate Belt connection bracket Belt spring clip 5 Pack 0 5/" x /" HHCS Pack 0 /" x /" SHCS Pack 8 mm flat washer 8 Pack 0 /" locking nut 9 Pack 0 T-nut 0 Pack 0 / x /" SHCS Horton carrier bar belt bracket Return pulley assembly, Chapter Door carrier bar Bottom of belt 5 Backplate assembly Motor gearhead 0 Anti-riser wheel Load wheel Fig Bottom of belt bracket assembly 0 Fig... Bottom of belt bracket assembly to carrier bar belt bracket 8 Fig... Header profile TIPS AND RECOMMENDATIONS Bottom of belt will attach to belt connection bracket for: Single door Right hand bi-part door Top of belt will attach to belt connection bracket for left hand bi-part door... Close single door or bi-part doors... Position bottom belt connection bracket.. Move bottom of belt until slots in belt connection bracket (Fig..) line up with carrier bar belt bracket slots on single door, or right hand bi-part door... Fasten carrier bar belt bracket.. Fasten carrier bar belt bracket to belt connection bracket with: () /" x /" SHCS (pack 0) () 8 mm flat washers (pack ) () /" locking nuts (pack 0).. Do not tighten nuts... Adjust belt connection bracket. Adjust position of belt connection bracket so that bottom of belt is level and perpendicular to belt, then tighten the two /" locking nuts (8)...5 Belt location adjustment. If required, adjust position of backplate or pulley assembly so that belt is straight.. Tighten fasteners after adjustment... Check door and installed components.. Slowly move door through full range of travel and check: Alignment of all installed components. Belt does not "walk" on pulleys. Freedom of door movement. Belt brackets do not contact ESA II controller. CAUTION Check that all fasteners have been tightened. ESA II DL

22 dormakaba ESA II I-Revive Slider Conversion Kit Chapter Belt connection bracket, top of belt. Fasten belt connection bracket to top of belt, LH bi-part door Top of belt Belt clamping plate Belt connection bracket Belt spring clip Pack 0 /" x /" SHCS Pack 8 mm flat washer 8 Pack 0 /" locking nut Horton carrier bar belt bracket Door carrier bar Bottom of belt Motor gearhead 0 Anti-riser wheel Load wheel Fig... Top of belt bracket assembly.. Locate position of belt connection bracket on top of belt.. RH door carrier bar belt bracket must be fastened to RH door carrier bar (Chapter ).. Close bi-part doors.. Temporarily fasten belt connection bracket to carrier bar belt bracket 8 (Fig...).. Place belt connection bracket on top of top of belt. 5. Mark both belt connection bracket edge 0 locations on top of belt.. Separate belt connection and carrier bar belt brackets... Secure belt connection bracket to top of belt. Refer to Para. 9. for pictures of assembly procedure.. Align belt connection bracket with marked bracket edge locations on top of belt (Para...).. Insert three tabs in belt clamping plate () into corresponding slots in belt connection bracket ().. Press eight teeth of belt into slots in belt clamping plate ().. Press clamping plate against belt connection bracket until belt teeth are fully inserted in clamping plate slots and clamping plate is parallel to belt connection bracket surface... Install belt spring clip.. Press belt spring clip () over ends of belt connection bracket and belt clamping plate until fully inserted as shown in Fig ESA II DL

23 dormakaba ESA II I-Revive Slider Conversion Kit Chapter 8 8 Top of belt connection to LH bi-part door 8. Fasten top of belt connection bracket to LH carrier bar belt bracket Top of belt Belt clamping plate Belt connection bracket Belt spring clip 5 Pack 0 5/" x /" HHCS Pack 0 /" x /" SHCS Pack 8 mm flat washer 8 Pack 0 /" locking nut 9 Pack 0 T-nut 0 Pack 0 / x /" SHCS Horton carrier bar belt bracket Return pulley assembly, Chapter Door carrier bar Bottom of belt 5 Backplate assembly Motor gearhead 0 Anti-riser wheel Load wheel Fig.8.. Fig Top of belt bracket assembly Top of belt bracket assembly to carrier bar belt bracket Fig.8.. Header profile Close bi-part doors. 8.. Position top belt connection bracket.. Move top of belt until slots in belt connection bracket (Fig 8..) line up with carrier bar belt bracket slots on left hand bi-part door. 8.. Fasten carrier bar belt bracket.. Fasten carrier bar belt bracket to belt connection bracket with: () /" x /" SHCS (pack 0) () 8 mm flat washers (pack ) () /" locking nuts (pack 0).. Do not tighten nuts. 8.. Adjust belt connection bracket.. Adjust position of belt connection bracket so that top of belt is level and bracket is perpendicular to belt, then tighten the two /" locking nuts (8) Belt location adjustment. If required, adjust position of backplate or pulley assembly so that belt is straight.. Tighten fasteners after adjustment. 8.. Check door and installed components.. Slowly move door through full range of travel and check: Alignment of all installed components. Belt does not "walk" on pulleys. Freedom of door movement. Belt brackets do not contact ESA II controller. CAUTION Check that all fasteners have been tightened. ESA II DL

24 dormakaba ESA II I-Revive Slider Conversion Kit Chapter 9 9 Header and sensor wiring 9. Connect existing control wiring to ESA II controller 9.. Connect existing control wiring. Connect existing control wiring to ESA II controller terminals. Reference Sections 8 and 9 of ESA II Controller Commissioning, Maintenance and Troubleshooting Instructions manual for terminal connections. 9. Connect 5 VAC wiring 9.. Check that 5 VAC circuit breaker to header is off. WARNING Electric shock hazard if circuit breaker not turned OFF! NOTICE Remove any existing activaton and presence sensor wiring. New IXIO-DT sensors and wiring are supplied with this kit. 9.. Door control switch wiring Control switch ESA II controller Program switch plug connection terminal On Partial open Hold Exit Ground On / Off Partial open Hold 5 8 Exit 8 NOTICE Discard door control power switch wiring. 9.. Connect 5 VAC wiring to 5 AC plug Connect 5 VAC wiring to 5 VAC plug at DC power supply. Reference Section of ESA II Controller Commissioning, Maintenance and Troubleshooting Instructions manual for 5 VAC wiring connections. 9. Header grounding Insure header ground wires, including header cover ground are connected to special T-slot bolt (Para..). WARNING Special T-slot bolt must be connected to building ground. 9. BEA IXIO-DT activation and presence sensors 9.. Install sensors. Using BEA IXIO-DT documentation, install sensors on sliding door assembly. 9.. Wire sensors. Reference Section 5 of ESA II Controller Commissioning, Maintenance and Troubleshooting Instructions manual for sensor wiring connections. ESA II DL

25 dormakaba I-Revive Slider Conversion Kit Chapter 0 0 Initial startup and programming 0. Door signage 0.. Place ESA door signage on door(s). Section, Door signage, sliding doors. ESA door signage information can also be found in ESA II I-Revive Slider Conversion Kit Owner's manual, Chapter. 0. Commissioning Refer to ESA II Controller Commissioning, Maintenance and Troubleshooting Instructions manual. 0.. Commission ESA II I-Revive Slider Conversion Kit. Section, Installation requirements prior to commissioning Section, First commissioning Section 8, Perform learning cycle Section 9, Set door parameters Section, Functional tests ESA II DL

26 dormakaba DORMA USA, Inc. Dorma Drive, Drawer AC Reamstown, PA 5 USA T: --88 F: --0

Victory CrossRoads CrossCountry CrossCountry Tour HardBall

Victory CrossRoads CrossCountry CrossCountry Tour HardBall by Trike Conversion Kit Victory CrossRoads CrossCountry CrossCountry Tour HardBall Installation Instructions Revised 3-2018 California Sidecar Parts & Technical Support 434.263.8866 Table of Contents:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Hidden Winch Mount For 2008 Ford Super Duty Kit 78105 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided

More information

INSTRUCTIONS INSTRUCCIONES CONSIGNES

INSTRUCTIONS INSTRUCCIONES CONSIGNES AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS

More information

TS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall)

TS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall) TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall) TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer

More information

* * M400 Series Double Locks. Double Electromagnetic Locks: M422, M452, M492. Installation Instructions. Mounting Bracket (2)

* * M400 Series Double Locks. Double Electromagnetic Locks: M422, M452, M492. Installation Instructions. Mounting Bracket (2) *44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Mounting Bracket (2) Inside Mounting Bracket Screws** (4) Mounting Bracket Screws**

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2007-2017 Chevy Silverado / GM Sierra / 1500-2500-3500 Ext. / Double / Crew Cab PART NUMBER: 56-13715, 56-13725 ITEM QUANTITY DESCRIPTION

More information

Floating Headers - 4-1/8, 4-1/2, 6. with RTS88 and PT21 for double doors ONLY. Installation instructions

Floating Headers - 4-1/8, 4-1/2, 6. with RTS88 and PT21 for double doors ONLY. Installation instructions - 4-1/8, 4-1/2, 6 with RTS88 and PT21 for double doors ONLY Installation instructions 933842 EN Table of Contents Table of contents 1 Technical specifications 3 1.1 Overview 3 1.1.1 General information

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS OUTLAW FRONT BUMPER APPLICATION: 2014-2018 TOYOTA TUNDRA PART NUMBER: 58-61035 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY 18MM WRENCH 2,3 2 MESHED

More information

M Damper Mount Linkage Kit Installation. Item Description Quantity Item Description Quantity Nuts 2

M Damper Mount Linkage Kit Installation. Item Description Quantity Item Description Quantity Nuts 2 FANs 268.1, 1628.3 Installation Bulletin M9000-150 Issue Date 0796 M9000-150 Damper Mount Linkage Kit Installation 21 18 19 20 2 22 17 2 4 3 2 15.5 393.7 1 17 16 15 11 13 12 8 9 10 2 5 Note: Damper mount

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

TS93 EMF T/PT/TDE. Surface applied door closer

TS93 EMF T/PT/TDE. Surface applied door closer TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress

More information

OEM TM-50 Quick Start Guide

OEM TM-50 Quick Start Guide This quick start guide provides basic setup and operating instructions for the OEM TM-50. The intended use of the OEM TM-50 Taping Machine is to produce taped reels of individually sealed and consistently

More information

Installation Instructions

Installation Instructions Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT 2011 & UP Ford Super Duty F-250/F-350/F-50 2011 & UP Part Number: 50073 WARNING: Under no circumstances do we recommend exceeding the towing

More information

I-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500

I-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500 PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat

More information

Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit A-Body P/N: &

Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit A-Body P/N: & Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit 1964-72 A-Body P/N: 030104 & 030105 The Detroit Speed A-Body front suspension kit is a bolt-on package that addresses the shortcomings of the

More information

Trike Conversion Kit ROADLINER, STRATOLINER, & STRATOLINER DELUXE

Trike Conversion Kit ROADLINER, STRATOLINER, & STRATOLINER DELUXE by Trike Conversion Kit ROADLINER, STRATOLINER, & STRATOLINER DELUXE Installation Instructions Revised 1-2015 California Sidecar Parts & Technical Support 434.263.8866 Table of Contents: 1. Warnings and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2009-2018 Dodge Ram 1500 (Excl. Rebel Model) 2019 Dodge Ram 1500 Classic PART NUMBER: 32-1960, 32-1965, 32-1960L, 32-1965L

More information

TOYOTA RAV FOG LIGHT KIT Preparation

TOYOTA RAV FOG LIGHT KIT Preparation Preparation Part Number: PT413-42163 Kit Contents Item # Quantity Reqd. Description 1 7 7 Wire Tie 2 4 #10-16 Cross Pan-Washer Head Screws 3 1 Switch 4 1 Relay 5 1 LH Fog Light Bezel 6 1 RH Fog Light Bezel

More information

NOTE: Refer to hardware list provided to identify fasteners supplied. Figure 2-1

NOTE: Refer to hardware list provided to identify fasteners supplied. Figure 2-1 NOTE: Read all instructions carefully, checking shop drawings supplied for any special conditions. Open all crated materials and check for damaged or missing parts prior to installation. NOTE: Proper operation

More information

Muto Electro Magnetic Lock (Elock MEM4400) Installation instructions / Wiring manual

Muto Electro Magnetic Lock (Elock MEM4400) Installation instructions / Wiring manual Muto Electro Magnetic Lock (Elock MEM4400) Installation instructions / Wiring manual 936033 05-2018 EN Table of Contents Table of contents 1 Technical specifications 3 1.1 Overview 3 1.1.1 General information

More information

TS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH)

TS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) Surface applied door closer Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) TABLE OF CONTENTS Technical specifications Size selection chart 2 Closer setup

More information

PFadvantage Metalfor Araus 1360

PFadvantage Metalfor Araus 1360 Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134

More information

SERVICE BULLETIN SB.DSL rev02

SERVICE BULLETIN SB.DSL rev02 DSL 505 Rear Delt / Pec Fly Cable Repair Applies to DSL 505 Rear Delt / Pec Fly built prior to 5/16/2017 Issue/Symptoms On some machines using the 1/8 diameter lift cables, the cam cables may twist and

More information

DORMA INTERIOR. DORMA PURE FAMELESS SLIDING Glass Wall Systems

DORMA INTERIOR. DORMA PURE FAMELESS SLIDING Glass Wall Systems TABLE OF CONTENTS Overview Intended use Structure requirements and fittings Requirements for glass panel Safety instructions Symbols used - safety/ installation Maintenance, care, repair Disposal 3 Overall

More information

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad

More information

2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014

2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &

More information

TOYOTA 4RUNNER CROSS BARS Preparation

TOYOTA 4RUNNER CROSS BARS Preparation Preparation Part Number: PT78-8970 Kit Contents Front Crossbar Assembly Rear Crossbar Assembly Hardware Bag Hardware Bag Contents Rubber Stopper 4 M6 Wafer Head Screw Load Label, 60kg 4 User Manual Additional

More information

BX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler

BX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler Operator Manual & Installation Instructions ALLURE Tow Bar (10,000 lb) Pintle Coupler Hooking Up to Towed Vehicle 1. Position the towing vehicle on a level surface with a straight driveway ahead and engage

More information

Installation Instructions

Installation Instructions BY Trike Conversion Kit KAWASAKI Vulcan 900 CLASSIC- CLASSIC LT AND CUSTOM MODELS 2006-CURRENT Installation Instructions Revised 1-2015 California Sidecar Parts & Technical Support 434.263.8866 2 Table

More information

Mobtown Offroad Toyota Tacoma Bolt On Rock Slider Installation Instructions

Mobtown Offroad Toyota Tacoma Bolt On Rock Slider Installation Instructions Mobtown Offroad 2005+ Toyota Tacoma Bolt On Rock Slider Installation Instructions Tools Needed: 9/16 Box Wrench 9/16 Standard and Deep Well Socket, 3/8 Drive Ratchet, 3/8 Drive 3/4 Standard Socket 3/4

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS OUTLAW REAR BUMPER APPLICATION: 2016-2018 Chevrolet Silverado 1500 PART NUMBER: 58-81005 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 REAR BUMPER 18MM WRENCH 2 4 SENSOR

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Fog Lamp Kit 2. APPLICATION: Pathfinder (2013) 3. PART NUMBER: 999F1 XZ000 - Fog Lamp Kit (P42K w/ AL) 999F1 XZ001 - Fog Lamp Kit (P42K w/o AL) 999F1

More information

INSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM

INSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting

More information

KEANE MONROE a member of the record group

KEANE MONROE a member of the record group SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully

More information

INSTRUCTIONS INSTRUCCIONES CONSIGNES

INSTRUCTIONS INSTRUCCIONES CONSIGNES AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 23-3790, 23-3795 E SERIES STEP BARS ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 STEP BARS 18MM

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For 63600 and 64040 Front Bumper and Winch Mount For Ford Super Duty Trucks As you read these instructions, you may see NOTES, CAUTIONS and WARNINGS. Each message has a specific

More information

Basic steps for installing the AmeriGlide Express Dumbwaiter

Basic steps for installing the AmeriGlide Express Dumbwaiter Basic steps for installing the AmeriGlide Express Dumbwaiter 1. Remove Shroud. 2. Mount lower section of Track and Unit to hoistway wall and Brackets. 3. Remove Shipping Bracket from Top of Car. 4. Install

More information

INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty

INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty Your safety, and the safety of others, is very important. To help you make informed decisions about safety,

More information

ROSBACK PRINTERS AND BOOKBINDER S MACHINERY Quality Bindery Equipment Since 1881

ROSBACK PRINTERS AND BOOKBINDER S MACHINERY Quality Bindery Equipment Since 1881 PRINTERS AND BOOKBINDER S MACHINERY Quality Bindery Equipment Since 1881 FIELD CONVERSION VACUUM KIT Part No. 220-A-121 (60Hz) Part No. 220-A-121-1 (50Hz) For TRUE-LINE 20" & 26" PERFORATORS MODELS 220A

More information

Instruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents

Instruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents Instruction Sheet Kit Numbers: 5600, 5700, 5800 & 5300 CRANK PULLEY KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand, and follow all safety

More information

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles

More information

READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION

READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION INSTALLATION INSTRUCTIONS Hot Fox In-Tank Fuel Warmer READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION Models covered by these instructions include: HFG 0-0 HFG 0- SHFT--0- SHH--0 TWHF 0- HFG

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Fog Lamp Kit Versa Note (SV Only) 999L1 4Z000 - Fog Lamp Kit Item QTY Description Service Part Number

More information

M400 Series Double Locks. Features

M400 Series Double Locks. Features *44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Automatic Voltage Selection (AVS) Magnet immediately detects 12VD or 24VD when power

More information

TOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation

TOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear

More information

KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump

KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump 30 Years Strong! Introduction The KT101 Series Governor System Installation Kit provides the necessary brackets and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2017 Ford F-250/350 PART NUMBER: 32-3900, 32-3905, 32-3900L, 32-3905L ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 ULTIMATE

More information

Rostselmash Torum 740

Rostselmash Torum 740 Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header

More information

INSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN Application: YAMAHA GRIZZLY 660

INSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN Application: YAMAHA GRIZZLY 660 INSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN 63172 Application: YAMAHA GRIZZLY 660 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message

More information

Guide to Installing Y o u r H a r m a r S t a i r L i f t

Guide to Installing Y o u r H a r m a r S t a i r L i f t Guide to Installing Y o u r H a r m a r S t a i r L i f t 2 W E L C O M E T O T H E H A R M A R F A M I L Y Congratulations on your purchase of a Harmar Access Stairway Lift. These instructions will assist

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2007-2016 Chevy Silverado / GM Sierra / 1500-2500-3500 PART NUMBER: 56-13715, 56-13725 CONTENT ITEM QUANTITY DESCRIPTION TOOLS

More information

w w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents

w w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents -J0447 REV. 008-08-05 CHROME FAN KIT GENERAL Kit Number 996-08 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English

More information

Current. Installation Instructions

Current. Installation Instructions by Trike Conversion Kit 2004 - Current Harley-Davidson Sportster Installation Instructions REVISED 4-2017 California Sidecar Parts & Technical Support 434.263.8866 Table of contents: 1. Warnings and Considerations

More information

Inverting Fault Circuit Breaker Kit for FlexPak 3000 and WebPak 3000 Digital DC Drives VAC and VAC

Inverting Fault Circuit Breaker Kit for FlexPak 3000 and WebPak 3000 Digital DC Drives VAC and VAC Inverting Fault Circuit Breaker Kit for FlexPak 3000 and WebPak 3000 Digital DC Drives 40-75 HP @ 230 VAC and 75-150 HP @ 460 VAC Model Numbers: 906FK1101 and 906FK1201 Instruction Manual D2-3330-2! ATTENTION:

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063

INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1

More information

TESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM

TESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER

More information

Chevrolet 3100 IFS Kit

Chevrolet 3100 IFS Kit 1947-54 Chevrolet 3100 IFS Kit Congratulations on your purchase on what we believe is the finest IFS kit available for 1947-54 Chevrolet pickups with stock frames. We have invested many hours into designing

More information

HP BladeSystem c7000 Carrier-Grade Options Installation Guide

HP BladeSystem c7000 Carrier-Grade Options Installation Guide HP BladeSystem c7000 Carrier-Grade Options Installation Guide Part Number 5991-8062 September 2009 (Second Edition) Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein

More information

Assembly Instructions for the CNCTRK AZ/EL Positioning Unit

Assembly Instructions for the CNCTRK AZ/EL Positioning Unit Assembly Instructions for the CNCTRK AZ/EL Positioning Unit Introduction/Overiview The AZ/EL Unit consists of two stages of identical gearboxes joined together with a configuration adapter. Note that this

More information

Digitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers

Digitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers Supersedes IL 33-858-4 Dated 05/02 Digitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers Digitrip Retrofit System for ITE K-3000, Digitrip Retrofit System for ITE K-3000, K-3000

More information

(6) Universal Mounting Brackets (NOTE: same bracket used for left or right side installation) Driver/left Running Board (example only)

(6) Universal Mounting Brackets (NOTE: same bracket used for left or right side installation) Driver/left Running Board (example only) PARTS LIST: Qty Description Qty Description 6 Universal Left/Right Mounting Brackets 12 6-1.0mm x 20mm T-Bolts 12 8-1.25mm Clip-On Nuts 12 6mm x 22mm OD x 2mm Flat Washers 12 8-1.25mm x 25mm Hex Bolt 12

More information

EVO-1162 EVO Tailgate Tire Carrier

EVO-1162 EVO Tailgate Tire Carrier EVO-1162 EVO Tailgate Tire Carrier Bill of Materials EVO-1162 Tailgate Tire Carrier Part number Description Quantity EVO-12161 EVO Tailgate Tire Carrier 1 EVO-12162 Bolt Plate 1 EVO-12163 Wheel Mount 1

More information

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number:

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number: Section I Installation Preparation Part Number: 08586 52960 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Mounting Bracket 3 1 GBS ECU 4 1 Security

More information

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:

More information

Universal Mounting Kit #0820

Universal Mounting Kit #0820 Universal Mounting Kit #0820 #1200 Super 5 th (16K) #0800 Super 5 th (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP WTW APPLICATION: 2007-2017 Chevy Silverado / GM Sierra / 1500-2500-3500 Ext. / Double / Crew Cab - 6.5 Ft Bed PART NUMBER: 56-534575, 56-534595,

More information

An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT

An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0562 Kepco KIT 219-0562 contains the PROMs used to upgrade the firmware for BOP

More information

Trike Conversion Installation Guide Kawasaki Vulcan 900 Classic, Classic LT, and Custom Models 2007 and Up Solid Axle Suspension

Trike Conversion Installation Guide Kawasaki Vulcan 900 Classic, Classic LT, and Custom Models 2007 and Up Solid Axle Suspension Trike Conversion Installation Guide Kawasaki Vulcan 900 Classic, Classic LT, and Custom Models 2007 and Up Solid Axle Suspension CAUTION: -Failure to make the proper adjustments will potentially lead to

More information

Driver Side Support Bracket pictured in "no-tow hook" direction. Reverse direction for tow hook equipped vehicles

Driver Side Support Bracket pictured in no-tow hook direction. Reverse direction for tow hook equipped vehicles PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect

More information

Congratulations on your purchase of a Mobile Ramps and Lifts lift.

Congratulations on your purchase of a Mobile Ramps and Lifts lift. 2 W E L C O M E T O T H E M O B I L E R A M P S A N D L I F T S Congratulations on your purchase of a Mobile Ramps and Lifts lift. These instructions will assist you in making sure your installation is

More information

INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING

INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, 76250 Application: 08-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make informed

More information

GPS Steering System Installation Manual

GPS Steering System Installation Manual GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D

More information

TOYOTA TUNDRA TVIP V4 Preparation

TOYOTA TUNDRA TVIP V4 Preparation Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation

More information

Sivoia QS Wireless Drapery Lite System

Sivoia QS Wireless Drapery Lite System Sivoia QS Wireless Drapery Lite System English Installation Guide Please Read Before Installing Important Notes - Please Read Before Installing A. Lutron systems are intended for use with only Lutron hardware

More information

2015 Mustang Lightbar (All Models) CDC#

2015 Mustang Lightbar (All Models) CDC# 2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket

More information

FRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!!

FRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!! INSTALLATION INSTRUCTIONS FOR 2009 DODGE 2500/3500 4WD & 1500 Mega Cab 6 SUSPENSION SYSTEM PART NUMBER 7206 Requires the following parts (sold separately) for a complete installation: Front Coil Spring

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave

More information

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO

More information

Part Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor

Part Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1

More information

T832 T842 ELECTRIC MOTOR OPTION ASSEMBLY MANUAL. Read & understand all instructions pertaining to this option prior to use!

T832 T842 ELECTRIC MOTOR OPTION ASSEMBLY MANUAL. Read & understand all instructions pertaining to this option prior to use! T832 T842 ELECTRIC MOTOR OPTION ASSEMBLY MANUAL Read & understand all instructions pertaining to this option prior to use! Safety Alert Watch for this ALERT Symbol. It identifies potential hazards to Personal

More information

MF 9690, 9790, Challenger 660, 670

MF 9690, 9790, Challenger 660, 670 Ag Leader Technology Parts List Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. MF 9690 MF 9790 Challenger 660 Challenger 670 Instruction

More information

ED50. Low energy automatic swing door operator. Service Manual

ED50. Low energy automatic swing door operator. Service Manual ED5 Low energy automatic swing door operator Service Manual DL6-6 -8 EN dormakaba ED5 Service Manual Table of Contents t Table of contents Table of contents General information Product description Safety

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 3.5 CONTOUR BULL BAR AUTOMOTIVE PRODUCTS, APPLICATION: 0-06 Chevrolet Silverado 500 PART NUMBER: 3-3000, 3-3005, 3-3005T, 3-3090, 3-3095, 3-3095T ITEM QUANTITY DESCRIPTION TOOLS

More information

SCION xa 2004 FOG LIGHT Section I Installation Preparation. Part Number: General Applicability

SCION xa 2004 FOG LIGHT Section I Installation Preparation. Part Number: General Applicability Section I Installation Preparation Part Number: 81025 52080 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Assembly, RH 2 1 Assembly, LH 3 1 Switch, 4 1 Relay, 5

More information

PFadvantage JD 3300/4400/6600/7700; 4420

PFadvantage JD 3300/4400/6600/7700; 4420 Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6

More information

(2) 12mm x 40mm Short Low Profile Bolt Plates. (2) Spacer Washers. (4) 12mm Plastic Retainers. Passenger/Right Front.

(2) 12mm x 40mm Short Low Profile Bolt Plates. (2) Spacer Washers. (4) 12mm Plastic Retainers. Passenger/Right Front. PARTS LIST: 1 Driver/Left Running Board with 1 Rubber Backing (use on SX & Limited models) 4 12mm Plastic Retainer 1 Passenger/Right Running Board with 1 Rubber 4 12mm Lock Washer Backing (use on SX &

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank you for purchasing ROLTECTM Electric Hopper Conversion. Agri-Cover, Inc. proudly manufactured this hardware using superior quality materials and workmanship. With proper

More information

Installation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included.

Installation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included. Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 9986 & 9996 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS OUTLAW FRONT BUMPER APPLICATION: 2016-2018 Chevrolet Silverado 1500 PART NUMBER: 58-61005 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY 18MM WRENCH

More information

P3066 INSTALLATION MANUAL

P3066 INSTALLATION MANUAL P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket

More information

SNOWPLOWS INSTALLATION MANUAL

SNOWPLOWS INSTALLATION MANUAL SNOWPLOWS HOME PRO 3000 INSTALLATION MANUAL Curtis Tractor Cab, Inc. and/or Curtis International, Inc. reserves the right to change product design or specifications without notice or liability. Curtis

More information

PSS 5000 Standard & Compact (For systems with CPB50x)

PSS 5000 Standard & Compact (For systems with CPB50x) Installation Guide Doms Forecourt Controller System PSS 5000 Standard & Compact () Date December 30, 2016 Document number PSS5000/INGU/805594/03 Doms ApS Formervangen 28 Tel. +45 4329 9490 info@doms.dk

More information

INSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091

INSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091 INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts

More information

TOYOTA RAV RUNNING BOARD

TOYOTA RAV RUNNING BOARD TOYOTA RAV4 2013 - RUNNING BOARD Part Number: 00016-42020 Accessory Code:TR1 Conflicts Mudguard Kit Contents Item # Quantity Reqd. Description 1 1 LH Board Assembly 2 1 RH Board Assembly 3 1 LH Rear Mounting

More information

INSTALLATION INSTRUCTIONS LD-1 REAR BUMPER RAM 1500 PART#R R #PW017838

INSTALLATION INSTRUCTIONS LD-1 REAR BUMPER RAM 1500 PART#R R #PW017838 INSTALLATION INSTRUCTIONS LD-1 REAR BUMPER PART#R102617 R102620 #PW017838 PARTS LIST: 1 LD1 Bumper Assembly 4 12-1.75mm x 40mm Hex Bolts 1 Push in License Plate Light 4 12mm x 37mm x 3mm Flat Washers 2

More information

Installation Instructions

Installation Instructions By Trike Conversion Kit for INDIAN MOTORCYCLES CLASSIC - VINTAGE - DARKHORSE CHIEFTAN & ROADMASTER MODELS 2014 - CURRENT Installation Instructions Revised 4-2017 California Sidecar Parts & Technical Support

More information