COOLEDGE TILE INTERIOR - SPECIFICATIONS SYSTEM OVERVIEW SPECIFICATION GENERAL FEATURES. DATE NOTE For Luminous Surfaces

Transcription

1 PROJECT SPECIFIED BY REFERENCE QUANTITY DATE NOTE For Luminous Surfaces SYSTEM OVERVIEW Create luminous ceilings, feature walls, and large graphics displays with Cooledge TILE Interior products 1 TILE Interior 2 TILE Interior Corner Kit (optional) 3 TILE Interior Cut-out Kit (optional) 4 TILE Interior Connector Kit 5 TILE Interior Starter Cable 6 LED Driver Included: TILE Interior Installation Kit (TACC-INT-INST) Also available: Extension Cables (TCBL-INT-LNG-10/20) GENERAL Location Operating Temp. Storage Temp. Relative Humidity Operating Voltage Electrical Connections Base Material Indoor, dry location only 0-40 C C 90% max (non-condensing) 58 VDC Tool-less snap connectors Flexible PET SPECIFICATION CE compliant lighting system inclusive of flexible light emitting sheets, connectors, low voltage cables, and LED drivers. Light output from the system must be +/- 10% of 6450/3225/1600 lumens/sqm across the total illuminated area post-installation. Color Rendering index (CRi) must be >90 and color consistency between light sheets must be typical 2 SDCM. Electrical connections between light emitting sheets and between cables and light emitting sheets must be tool-less and allow more than one connect/disconnect. System must be configurable onsite and include the capability to accommodate obstacles, angles, and curves. System warranty must be a minimum of 5 years. FEATURES Three choices of constant lumen output ensure consistent highly calibrated illumination Color consistency of typically 2 SDCM between TILEs meets stringent requirements for large area installations Cut-to-fit means systems are adaptable to any size installation and can accommodate obstacles and shapes Constant voltage electrical architecture is fully scalable without loss of performance or need to reconfigure drivers Low setback distances, flexibility, and no requirement for a heat sink enable optimal integration into luminous surfaces Multiple options for dimming, lumens, and CCT offer the most adaptable illumination for large surface areas available today Mounts directly to most common non-conductive construction materials (eg. drywall, plywood) Cooledge Lighting reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program. PSD-0001-R /6

2 5 YEAR SYSTEM WARRANTY 5 YEAR SYSTEM WARRANTY COOLEDGE TILE INTERIOR - SPECIFICATIONS PHOTOMETRICS 1 Light Output (lm) - per TILE 600, 300, 150 Light Output (lm/m 2 ) 6450, 3225, 1600 Correlated Color Temperature (CCT) Color Rendering Index (CRI) 90 Color Uniformity Lumen Maintenance K, 3000K, 3500K, 4000K, 5700K 2 SDCM (typical) L80 = 75,000hr IESNA TM DATA CCT Rf Rg 2700K K K K K Photometric files available from cooledgelighting.com 2 Based on LM80 data & TM-21 calculations POWER CERTIFICATIONS Light Output (lm) CCT Power (W) Power (W/m 2 ) 2700K K EN Compliant (as a system) K K K K K K WARRANTY 4000K K K K Year Limited Warranty: Parts and workmanship when used with a Cooledge approved power supply K K K PSD-0001-R /6

3 1 TILE INTERIOR 305mm 239mm 178mm 117mm 56mm 298mm TILE - INT WHT Example: TILE-INT WHT TILE FLUX 600 = 600lm 300 = 300lm 150 = 150lm CCT 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K 57 = 5700K FINISH WHT = White 2 TILE INTERIOR CORNER INCLUDED (1) Corner TILE (1) Connector strip 610mm (4) Single jumper (1) Double jumper (long) Purpose: Cut-to-fit in corners where a full TILE does not fit in the space; or to step cut along angles and curves at the edge of a luminous surface (optional depending upon layout). TACC - INT - COR - - Example: TACC-INT-COR TACC = TILE Accessory COR = Corner Kit FLUX 600 = 600lm 300 = 300lm 150 = 150lm CCT 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K 57 = 5700K PSD-0001-R /6

4 3 TILE INTERIOR CUT-OUT INCLUDED (1) Cut-out TILE (1) Single Jumper (long) Purpose: Cut-to-fit around obstacles located in the middle of a luminous surface such as standoffs, support cables/rods, beams, pipes, etc. (optional depending on layout). Cut to fit around obstacle Jumper Connection (Input missing) Jumper Connection (Output missing) TACC - INT - CUT - - Example: TACC-INT-CUT TACC = TILE Accessory CUT = Cut-out Kit FLUX 600 = 600lm 300 = 300lm 150 = 150lm CCT 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K 57 = 5700K PSD-0001-R /6

5 4 TILE INTERIOR CONNECTOR Purpose: Makes the electrical connection to the first TILE in each run. Connects to two TILE runs and may be connected to additional connector strips (required). INCLUDED (1) Connector Strip (610mm length) (4) Single Jumper (1) Double Jumper TACC - INT - CON Example: TACC-INT-CON TACC = TILE Accessory CON = Connector Kit 5 TILE INTERIOR STARTER CABLE Purpose: Makes the electrical connection between the LED driver and the connector strips that deliver power to the TILEs (required). Length = 3m TCBL - INT - STR Example: TCBL-INT-STR TCBL = TILE Cable STR = Starter Cable PSD-0001-R /6

6 6 LED DRIVERS Purpose: Convert AC mains (line) power to safe, low voltage DC power. Cooledge LED drivers are offered with a range of dimming options (required). CE COMPLIANT DRIVERS - INTERIOR MODEL OUTPUT POWER (W) INPUT VOLTAGE (VAC) OUTPUT VOLTAGE (VDC) DIMMING PSS Constant Voltage 90 NOM No PSD Constant Voltage 90 NOM V Detailed specifications for Cooledge LED drivers with ordering codes and dimming options are available in the following documents: Cooledge CE Compliant LED Drivers - Specifications ADDITIONAL ACCESSORIES EXTENSION CABLES 1.3mm 2 cable (non-plenum rated) Available in 3m & 6m lengths Crimp Connector Purpose: Cable between TILE Starter Cable and LED Driver that extends the distance of the driver may be remotely located away from the TILEs. Please consult Cooledge for additional information including requirements for plenum rated cables. Starter Cable ~ Extension Cable LED Driver PROTOCOL CONVERTERS DALI 0/1-10V DMX 0/1-10V CONTROLLER PROTOCOL CONVERTER Purpose: A device that converts control signals from a DALI or DMX controller to 0/1-10V signals to operate Cooledge LED drivers. One converter may be used to control many LED drivers. Please consult Cooledge for the best option for your project. (SUPPLIED BY OTHERS) LINE VIOLET BLACK GREY NEUTRAL WHITE DRIVER RED GREEN/YELLOW BLACK EARTH WIRE ELECTRICAL ENCLOSURE NUT Example only: wiring details may vary by region TO TILES STARTER CABLE EXTENSION CABLE CRIMP CONNECTOR IF REQUIRED CONNECTOR STRIP PSD-0001-R /6