FireLock V36, K8.0 Models V3611, V3612

Transcription

1 FireLock V36, K8.0 Models V3611, V Dry Type Pendants Standard and Quick Response Technical Specifications: Models: V3612 and V3611 Style: Horizontal Sidewall and Recessed Horizontal Sidewall Flush Horizontal Sidewall Dry Recessed Horizontal Sidewall Nominal Orifice Size: 17/32"/14 mm Orifice Insert: Stainless steel per UNS S30300 K-Factor: 8.0 Imp./11.5 S.I. 1 Nominal Thread Size: 1" NPT/33.7 mm Dry Sleeve & Skirt Horizontal Sidewall Extended Horizontal Sidewall Plain Horizontal Sidewall Max. Working Pressure: 175 psi/1200 kpa Approvals/Listings: See Victaulic Publication for more details. Factory Hydrostatic Test: 500 psi/3450 kpa Min. Operating Pressure: 7psi/48kPa Temperature Rating: See chart on page 3. 1 For K-Factor when pressure is measured in Bar, multiply S.I. units by Product Description: The V36 Dry Sprinkler is used in special applications such as freezing environments and conditions where sediment or foreign materials might accumulate in ordinary horizontal pipe nipples. The Model V36 Dry Type Horizontal Sidewall Sprinkler utilizes a frangible glass bulb. At the bulb s rated temperature, the sprinkler opens releasing the bulb seat assembly, causing the inner tube assembly to move, allowing the spring assembly to pivot alongside the inner tube. At this time, water flows through the sprinkler and is distributed by the deflector, in an approved discharge pattern. Coverage: For coverage area and sprinkler placement, refer to NFPA 13 or applicable standards. Exaggerated for clarity Exaggerated for clarity Job/Owner System No. Location Contractor Submitted By Engineer Spec Section Paragraph Approved Date Date victaulic.com Sprinklers FireLock K8.0, V36 Publication Rev. K Updated 6/ Victaulic Company. All rights reserved. 1

2 victaulic.com Sprinklers FireLock K8.0, V36 Publication Material Specifications: Deflector: Brass per UNS C22000 or Stainless Steel per UNS S30400 Bulb: Glass with glycerin solution Bulb Nominal Diameter: Standard: 5.0 mm Quick Response: 3.0 mm Split Spacer: Stainless steel per UNS S30300 Load Screw: Brass per UNS C36000 Pip Cap: Stainless steel per UNS S30300 Spring Seal Assembly: Teflon 2 coated Beryllium nickel alloy and stainless steel per UNS S30300 Frame: Die cast brass Outer Tube: Galvanized steel pipe Inner Tube: Stainless steel per UNS S30400 Escutcheon/Plate: mild steel and stainless steel Torsion Spring: SST Wire Accessories Installation Wrench: Model V36 Open End and Recessed Wrenches fit all V36 Series frames. Sprinkler Finishes: Plain brass Chrome plated White painted 3 4 Flat black painted 3 4 Custom painted 3 4 Proprietary Nickel Teflon 2 Coated 4 VC , 200, 286 SR Only: Wax 4 For cabinets and other accessories refer to separate sheet. 2 Teflon is a registered trademark of Dupont Co. 3 Not available on the Intermediate Level Style Pendent. 4 UL Listed for corrosion resistance. 5 UL Listed and FM Approved for corrosion resistance. NOTE: Weather resistant escutcheon available upon request. APPROVED Rev. K Updated 6/ Victaulic Company. All rights reserved. victaulic.com 2

3 victaulic.com Sprinklers FireLock K8.0, V36 Publication Approvals/Listings: APPROVALS/LISTINGS Model V3612 V3612 V3611 V3611 Orifice Size (inches) 17/32 17/32 17/32 17/32 Orifice Size (mm) Nominal K Factor Imperial Nominal K Factor S.I Response Quick Quick Standard Standard Deflector Type Horizontal Sidewall Approved Temperature Ratings culus F/57 C 155 F/68 C 200 F/93 C 286 F/141 C 6 For K-Factor when pressure is measured in Bar, multiply S.I. units by Approved for V3605 and V3606 dry sprinklers up to 48" length. Note: Listings and approval as of printing. Light hazard or ordinary hazard. Recessed Horizontal Sidewall 135 F/57 C 155 F/68 C 200 F/93 C 286 F/141 C F /C Horizontal Sidewall 135 F/57 C 155 F/68 C 200 F/93 C 286 F/141 C APPROVED Recessed Horizontal Sidewall 135 F/57 C 155 F/68 C 200 F/93 C 286 F/141 C Dimensions: NOTE : The A dimension of a dry sprinkler, which extends into a freezer from a wet piping system, must take into account the wall or ceiling thickness of the freezer. See IMPORTANT INSTALLATION INFORMATION later in this document. "A" (Min. 1¼") ¼" "A" (Min. 1¼") 1" NPT 1" NPT Two Piece Escutcheon 3 " Dia. Tee with same outlet size size size as sprinkler thread size. See Important Installation Information, later in this document 1½" Min. Dia. Hole in Wall Flush 3" Dia. 2½" 1¾" Min. Dia. Tee with size Hole in Wall Tee with same outlet size as sprinkler threadsize as sprinklerthreadsize. See Important Installation Information, later in this document 3" Min. 4½" Max. 1" NPT "A" (Min. 1½") Sleeve & Skirt 1" NPT Tee Tee with same outlet size size as sprinkler as thread sizesize. See page 4, No. 2 See Important Installation Information, later in this document Plain Barrel 2 " "A" (Min. 1¾") 1½" Min. Dia. Hole in Wall Collar Wall Cup 3½" Dia. 1" NPT 2 " Dia. Tee with same Tee with outlet same outlet size size as sprinkler thread size as sprinkler thread size. See Important Installation Information, later in this document "A" (Min. 1¼") Extended Two Piece Escutcheon 4" Min. 5¼" Max. Tee Tee with with same outlet size size as sprinkler as thread sizesize. See Important Installation Information, later in this document 2" Min. Dia. Hole in Wall Recessed 1 " Min. 2 " Max. Deflector To Ceiling Distance 4 12"/ mm For All Configurations Shown Above Rev. K Updated 6/ Victaulic Company. All rights reserved. victaulic.com 3

4 victaulic.com Sprinklers FireLock K8.0, V36 Publication Important Installation Information: For detailed installation instructions, see publication I-40. No. 1 Victaulic Model V36 Series Dry sprinklers should be installed in accordance with NFPA 13. These sprinklers are to be installed using a pipe wrench applied to the outer tube. When this is not possible, the proper sprinkler wrench may be used with extreme care for lengths up to approximately 18". Excessive force may distort the frame thus destroying the unit. No. 2 Dry sprinklers MUST be installed only into the outlet of a cast or malleable iron tee. No. 3 DO NOT install dry sprinklers into any couplings or threaded elbows. In addition, DO NOT install dry sprinklers into any fitting that interferes with thread penetration. NOTE : The end seal of the dry sprinkler MUST NOT bottom out in the fitting. A See Note End Seal C Exposed Minimum Barrel Length (Refer to Table) D HEATED SPACE Diameter of hole is dependent upon the type of escutcheon selected. Space must be sealed to prevent condensation from forming, per NFPA requirements. Insulation Wall or Ceiling of Freezer NOTE : The A dimension of a dry sprinkler, which extends into a freezer from a wet piping system, must take into account the wall or ceiling thickness of the freezer. The minimum length of the dry sprinkler should not be less than the lengths specified in the following table, plus the thickness of the freezer s wall or ceiling ( A = C + D ). Refer to the drawing for a representation of the A dimension. DO NOT attempt to modify dry sprinklers, since they are manufactured to this specific A dimension. The following table is used when the ambient temperature is maintained between 40 F/4 C and 60 F/16 C around the wet piping system. Ambient Temperature Exposed to Discharge End of Sprinkler F/ C Exposed Minimum Barrel Length inches/mm APPROVED 40 F/4 C 50 F/10 C 60 F/16 C Note: Exposed minimum barrel lengths are inclusive up to 30-mph/48-kph wind velocities COLD SPACE Exaggerated for Clarity TYPICAL SLEEVE AND SKIRT CONFIGURATION FOR EXAMPLE ONLY Rev. K Updated 6/ Victaulic Company. All rights reserved. victaulic.com 4

5 victaulic.com Sprinklers FireLock K8.0, V36 Publication Distribution Patterns: Models V3612, V3611 Horizontal Sidewall and Recessed Horizontal Sidewall Distribution Patterns Trajectory 10' 3.0 m 8' 2.4 m 6' 1.8 m 4' 1.2 m 2' 0.6 m 0 2' 0.6 m 10' 2.4 m3.0 m 4' 1.2 m1.8 6' m 8' 12' 3.7 m 14' 16' 22' 4.3 m4.9 m5.5 18' m6.1 20' m6.7 m 24' 7.3 m 26' 7.9 m 7 psi 48 kpa 15 psi 103 kpa 30 psi 207 kpa Models V3612, V3611 Horizontal Sidewall and Recessed Horizontal Sidewall Distribution Patterns Plan View 0 2' 0.6 m 4' 1.2 m 6' 1.8 m 8' 2.4 m 10' 3.0 m 12' 3.7 m 14' 4.3 m 16' 4.9 m 2' 0.6 m 4' 1.2 m 6' 1.8 m 8' 7 psi 48 kpa 10' 2.4 m3.0 m 12' 3.7 m 15 psi 103 kpa 14' 16' 22' 4.3 m4.9 m 18' 5.5 m 20' 6.1 m6.7 m 30 psi 207 kpa 24' 7.3 m 26' 7.9 m 28' 8.5 m NOTES: A. Data shown is approximate and can vary due to differences in installation. B. These graphs illustrate approximate trajectories, floor-wetting, and wall-wetting patterns for these specific Victaulic FireLock automatic sprinklers. They are provided as information for guidance in avoiding obstructions to sprinklers and should not be used as minimum sprinkler spacing rules for installation. Refer to the appropriate NFPA National Fire Code and the Authority Having Jurisdiction for specific information regarding obstructions, spacing limitations and area of coverage requirements. Failure to follow these guidelines could adversely affect the performance of the sprinkler and will void all Listings, Approvals and Warranties. C. All patterns are symmetrical to the centerline of the waterway Rev. K Updated 6/ Victaulic Company. All rights reserved. victaulic.com 5

6 victaulic.com Sprinklers FireLock K8.0, V36 Publication Ratings: All glass bulbs are rated for temperatures from -67 F/-55 C to those shown in table below: Available Wrenches: Model V36 Open End and Recessed Wrenches fit all V36 Series frames. Sprinkler Temperature Victaulic Part Nominal Temperature ClassificationIdentification Rating Temperature ºF/ºC Maximum Ambient Temperature Allowed Glass Bulb Color Ordinary A 135ºF/57ºC 100ºF/38ºC Orange Ordinary C 155ºF/68ºC 100ºF/38ºC Red Intermediate E 175ºF/79ºC 150ºF/65ºC Yellow Intermediate F 200ºF/93ºC 150ºF/65ºC Green High J 286ºF/141ºC 225ºF /107ºC Blue Extra High K 360ºF/182ºC 300ºF/149ºC Purple M Open No Bulb WARNING Always read and understand installation, care, and maintenance instructions, supplied with each box of sprinklers, before proceeding with installation of any sprinklers. Always wear safety glasses and foot protection. Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products. Installation rules, especially those governing obstruction, must be strictly followed. Painting, plating, or any re-coating of sprinklers (other than that supplied by Victaulic) is not allowed. Failure to follow these instructions could result in serious personal injury and/or property damage. The owner is responsible for maintaining the fire protection system and devices in proper operating condition. For minimum maintenance and inspection requirements, refer to the current National Fire Protection Association pamphlet that describes care and maintenance of sprinkler systems. In addition, the authority having jurisdiction may have additional maintenance, testing, and inspection requirements that must be followed. If you need additional copies of this publication, or if you have any questions about the safe installation of this product, contact Victaulic World Headquarters: P.O. Box 31, Easton, Pennsylvania USA, Telephone: Installation Reference should always be made to the I-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at Warranty Refer to the Warranty section of the current Price List or contact Victaulic for details. Note This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications and standard equipment without notice and without incurring obligations. Trademarks Victaulic and Firelock are registered trademarks of Victaulic Company Rev. K Updated 6/ Victaulic Company. All rights reserved. victaulic.com 6

7 Existing UprightSprinklers APPROVED Worldwide Contacts Series ELO K-factor Upright and Pendent Sprinklers Standard Response,Standard Coverage General Description TYCO Series ELO K Standard Response, Standard Coverage Upright and Pendent Sprinklers (Ref. Figure 1) are automatic sprinklers of the fusible solder type. They are standard response, spray sprinklers that produce a hemispherical water distribution pattern below the deflector. The 11.2 K-factor, ELO-231 Sprinklers were subjected to full scale, high-piled storage, fire tests to qualify their use in lieu of 5.6 or 8.0 K-factor standard spray sprinklers for the protection of high-piled storage. Higher flow rates can be achieved at much lower pressures with the 11.2 K-factor, ELO-231 Sprinklers, making their use highly advantageous in high density applications, such as the protection of high-piled storage. Wax or lead coatings can be used to extend the life of the copper alloy components used in Series ELO-231 sprinklers beyond that which would otherwise be obtained when exposed to corrosive atmospheres. Although wax and lead coated sprinklers have passed the standard corrosion tests of the applicable approval agencies, the testing is not representative of all possible corrosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suitability of these corrosion resistant coatings for any given corrosive environment. The effects of ambient temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An upright intermediate level version of the Series ELO-231 Sprinklers for in-rackapplications can be obtained by utilizing the Series ELO-231 Upright Sprinkler with the WSG-2 Guard & Shield, and a pendent intermediate level version of the Series ELO-231 Sprinklers can be obtained by utilizing the Series ELO-231 Pendent Sprinkler with the WS-2 Shield. If there is a possibility of the pendent intermediate level version being exposed to mechanical damage, a G-2 Guard can be added. NOTICE The 11.2 K-factor, Series ELO-231 Upright and Pendent Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association (NFPA), in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. Contact the installing contractor or product manufacturer with any questions. Installation of Series ELO-231 Pendent Sprinklers in recessed escutcheons will void all sprinkler warranties, as well as possibly void the sprinkler s Approvals and/or Listings. Sprinkler Identification Numbers (SINs) TY5111 Upright 11.2K, 3/4 NPT TY5211 Pendent 11.2K, 3/4 NPT TY5811 Upright 11.2K, 1/2 NPT TY5111 is a redesignation for Central SIN C5111. TY5211 is a redesignation for Central SIN C5211. TY5811 is a redesignation for Central SIN C5811. IMPORTANT Always refer to Technical Data Sheet TFP700 for the INSTALLER WARNING that provides cautions with respect to handling and installation of sprinkler systems and components. Improper handling and installation can permanently damage a sprinkler system or its components and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 JANUARY 2017 TFP340

8 TFP340 Page 2 of /16" (71,4 mm) TYP. 7/16" (11,1 mm) NOMINAL MAKE-IN UPRIGHT TY5811 WRENCH FLATS 1/2" NPT 1/2" (12,7 mm) NOMINAL MAKE-IN UPRIGHT TY5111 THREAD RELIEF 3/4" NPT 1/2" (12,7 mm) NOMINAL MAKE-IN PENDENT TY5211 3/4" NPT CROSS SECTION APPROVED Components: 1 - Frame 2 - Seal Disc 3 - Cap 4 - Strut Assembly 5 - Compression Screw 6 - De ector* 7 - Helper Spring 8 - Ejector Spring 9 - Strut Clip * Temperature rating is indicated on de ector Technical Data Approvals UL and C-UL Listed FM Approved NYC Approved (Refer to Table A for complete approval information, including corrosion-resistant status. The approvals apply to the service conditions indicated in the Design Criteria section.) Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K=11.2 gpm/psi 1/2 (161,4 lpm/bar 1/2 ) Temperature Ratings Refer to Table A Finishes Refer to Table A Physical Characteristics Frame Bronze Seal Disc Copper Cap Bronze Strut Assembly..Solder, Bronze Stainless Steel Compression Screw Bronze Deflector Bronze Helper Spring Stainless Steel Ejector Spring Nickel Strut Clip Stainless Steel Design Criteria FIGURE 1 SERIES ELO K UPRIGHT - 3/4 NPT (TY5111), UPRIGHT - 1/2 NPT (TY5811), AND PENDENT - 3/4 NPT (TY5211) SPRINKLERS UL and C-UL Listing Requirements TYCO Series ELO K Standard Response, Standard Coverage Upright and Pendent Sprinklers are to be installed in accordance with NFPA 13 standard sprinkler position and area/ density flow calculation requirements for light, ordinary, or extra hazard occupancies, as well as high piled storage occupancies (solid piled, palletized, rackstorage, bin box, and shelf storage including but not limited to Class I-IV and Group A plastics) with a minimum residual (flowing) pressure of 7 psi (0,5 bar) for wet or dry pipe systems. FM Approval Requirements The 11.2 K-factor, Model ELO-231 (TY5111, TY5211, and TY5811) Sprinklers are to be installed in accordance with the applicable control mode density/area guidelines provided by FM Global. (FM Approval guidelines may differ from UL and C-UL Listing criteria.) Operation A fusible alloy is sealed into a bronze actuating rod (center strut) by a stainless steel ball. When the alloy melts at its rated temperature, the ball is forced upward into the center strut, releasing the two ejectors and operating the sprinkler. Installation TYCO Series ELO K Standard Response, Standard Coverage Upright and Pendent Sprinklers must be installed in accordance with this section. A leak-tight 3/4 inch NPT sprinkler joint should be obtained by applying a minimum-to-maximum torque of 10 to 20 lbs.-ft. (13,4 to 26,8 Nm). A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a minimum-tomaximum torque of 7 to 14 lbs.-ft. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler inlet with consequent leakage or impairment of the sprinkler. "FITTING SIDE" TOWARDS SPRINKLER FITTING WRENCH RECESS (END "A") FIGURE 2 W-TYPE 3 SPRINKLER WRENCH Do not attempt to make up for insufficient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. The Series ELO-231 Upright and Pendent Sprinklers must be installed in accordance with the following instructions: Step 1. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 3 Sprinkler Wrench (Ref. Figure 2), except that an 8 or 10 inch adjustable Crescent wrench is to be used for wax coated sprinklers. With reference to Figure 1, the W-Type 3 Sprinkler Wrench or the adjustable wrench, as applicable, is to be applied to the wrench flats.

9 TFP340 Page 3 of 4 SPRINKLER TYPE UPRIGHT (TY5111 & TY5811) PENDENT (TY5211) Notes: 1. UL Listed 2. C-Ul Listed TEMPERATURE RATING FRAME COLOR 165 F (74 C) Unpainted 212 F (100 C) White NATURAL BRASS 1, 2, 3, 4 CHROME PLATED SPRINKLER FINISH LEAD COATED WAX COATED 1, 2, 3, 4 WAX-OVER-LEAD COATED 286 F (141 C) Blue 1, 2, 3, 4 1*, 2*, 3*, 4* 165 F (74 C) Unpainted 212 F (100 C) White 1, 2, 3, 4 1, 2, F (141 C) Blue 1, 2, 4 1*, 2*, 4* 3. FM Approved 4. Approved by the City of New York (NYC) under MEA E * Listed/Approved for a maximum ceiling temperature of 150 F (66 C) TABLE A 11.2K SERIES ELO-231 UPRIGHT & PENDENT SPRINKLERS, STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS APPROVED When installing wax-coated sprinklers with the adjustable wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corrosive environment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damaging the wax coating. Before wrench-tightening the sprinkler, the jaws of the wrench are to be adjusted to just contact the sprinkler wrench flats. After wrench-tightening the sprinkler, loosen the wrench jaws before removing the wrench. After installation, the sprinkler wrench flats and frame arms must be inspected and the wax coating re-touched (repaired) whenever the coating has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gently applying a heated 1/8 inch diameter steel rod to the areas of wax that have been damaged, to smooth it backover areas where bare metal is exposed. Note: Only retouching of the wax coating applied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precautions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. If attempts to retouch the wax coating with complete coverage are unsuccessful, additional wax can be ordered in the form of a wax stick (the end of which is color coded). Only the correct color-coded wax is to be used, and retouching of wrench flats and frame arms is only permitted at the time of initial sprinkler installation. With the steel rod heated as previously described, touch the rod to the area requiring additional wax with the rod angled downward, and then touch the wax stick to the rod approximately 1/2 inch away from the area requiring retouching. The wax will melt and run down onto the sprinkler. Care and Maintenance TYCO Series ELO K Standard Response, Standard Coverage Upright and Pendent Sprinklers must be maintained and serviced in accordance with this section. Before closing a fire protection system control valve for maintenance workon the fire protection system that it controls, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modified or over-heated sprinklers must be replaced. Care must be exercised to avoid dam-age to the sprinklers before, during, and after installation. Sprinklers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Frequent visual inspections are recommended to be initially performed for corrosion resistant sprinklers, after the installation has been completed, to verify the long term potential integrity of the sprinkler coatings. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of inspecting from the floor level, a random sampling of close-up visual inspections should be made, so as to better determine the exact sprinkler condition and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the installing contractor or product manufacturer with any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes.

10 TFP340 Page 4 of 4 APPROVED P/N 50 XXX X XXX Limited Warranty For warranty terms and conditions, visit SIN K UPRIGHT (3/4 NPT) TY K PENDENT (3/4 NPT) TY K UPRIGHT (1/2 NPT) TY2811 Ordering Procedure SPRINKLER FINISH NATURAL BRASS WAX COATED LEAD COATED WAX-OVER-LEAD COATED CHROME PLATED Contact your local distributor for availability. When placing an order, indicate the full product name and part number (P/N). Sprinkler Specify: ELO K Standard Response (specify Pendent or Upright) Sprinkler, SIN (specify), temperature rating (specify), with (specify) finish, P/N (specify from Table B) Sprinkler Wrench Specify: W-Type 3 Sprinkler Wrench, P/N TEMPERATURE RATING F (74 C) F (100 C) F (141 C) TABLE B SERIES ELO K UPRIGHT AND PENDENT SPRINKLERS, STANDARD RESPONSE PART NUMBER SELECTION Wax Sticks (for retouching wrench-damaged wax coating) Specify: (specify Color) color-coded Wax Stickfor retouching (specify temperature rating) temperaturerated Series ELO-231 Sprinklers, P/N (specify): Red for 165 F Blue for 212 F and 286 F Note: Each wax stick is suitable for retouching up to twenty-five sprinklers. The wax used for 286 F sprinklers is the same as for 212 F sprinklers, and, therefore, the 286 F sprinkler is limited to the same maximum ceiling temperature as the 212 F sprinkler (i.e., 150 F). GLOBAL HEADQUARTERS 1400 Pennbrook Parkway, Lansdale, PA Telephone Copyright 2017 Tyco Fire Products, LP. All rights reserved.

11 Bulletin 129 Rev. L Model G XLO K11.2 (160 metric) Standard Spray Standard Response APPROVED Storage and Non-storage Sprinkler Bulletin 129Rev. L Extra Large Orifi ce Sprinkler (SIN R2921) Upright (SIN R2916) Pendent Features 1. UprightcULus Listed as a Control Mode Density Area (CMDA) sprinkler for storage & non-storage protection. 2. Uprightand PendentFM Approved as Standard-response, storage, non-storage and CMDA sprinklers. 3. Standard ¾-inch NPT or ISO 7-R¾ threads; optional ½-inch NPT or ISO 7-R½ threads for uprightretrofitapplications only. 4. The ¾ G XLO uprightis culus listed to be used with the D-6 guard/shield and is FM approved to be used with the D-7 guard/shield. The G XLO pendentis FM approved to be used with the D-8 guard or the D-9 guard/ shield. See Bulletin 208. Listings & Approvals: The following organizations provide Listings or Approvals for Model G XLO sprinklers. See the Technical Data table for listing and approvals applicable to each sprinkler. 1. Underwriters Laboratories, Inc. and Underwriters Laboratories of Canada (culus) - Uprightonly. 2. Approved by Factory Mutual (FM) as a storage, non-storage, and CMDA sprinkler - Uprightand Pendenṭ UL Guide Number VNIV UL Listing Category Sprinklers, Automatic and Open; Sprinklers for Storage Protection (Control Mode Density Area) Model G XLO Upright Model G XLO Pendent Product Description The Reliable Model G XLO sprinkler is a center strut, solder in compression, extra large orifice sprinkler thathas been designed for storage and non-storage applications. The Model G XLO sprinkler is available in either an uprightor pendentconfiguration. The Model G XLO sprinkler is available with either 3/4-inch NPT or ISO 7-R3/4 threads. The Model G XLO Upright is optionally available with either 1/2-inch NPT or ISO 7-R1/2 threads for retrofitapplications only. Design Criteria The Model G XLO sprinkler is intended for use as a standard response standard spray sprinkler in hydraulically designed sprinkler systems with a minimum pressure of 7 psi (0.5 bar) in accordance with the area/density curves of NFPA 13 or in accordance with FM Property Loss Prevention Data Sheets. The Model G XLO sprinkler is nota Large Drop or ESFR sprinkler. Temperature Ratings Sprinkler Maximum Ambient Frame Classifi cation Rating Temperature Color F C F C Ordinary Uncolored Intermediate White High Blue Technical Data Nominal K Factor Sprinkler Sprinkler Sprinkler Type Height Approvals Identifi cation US Metric Number (SIN) Upright Orifice with culus, FM (68.8mm) R2921 ¾ NPT (R¾) Upright Retrofit culus, FM Orifice with (71.6mm) R2921 ½ NPT (R½) Pendent Orifice with FM R2916 (68.8mm) ¾ NPT (R¾) Note: This producthas been tested and listed for storage applications to qualify its use in lieu of 5.6K or 8.0K Factor sprinklers for the protection of high-piled storage. Finishes Standard Finishes Bronze Chrome (3) Special Application Finishes Lead Plated Wax (1) (2) (3) Wax/Lead (1) (3) (1) (2) (3) F (74 C), 212 F (100 C) and 286 F (141 C) Temp. Ratings F (74 C) Clear Wax, 212 F (100 C) Brown Wax F (74 C) Clear Wax, 212 F (100 C) Brown Wax (1) culus. (2) 212 F (100 C) Brown wax may be used on 286 F (141 C) Sprinklers when maximum ambienttemperatures do notexceed 150 F (66 C). (3) Uprightonly. Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523

12 Installation Reliable s Model G XLO sprinkler mustbe installed according to NFPA Standards or the appropriate Factory Mutual Loss Prevention Data Sheets for all area/density methods of design as well as requirements of the Authority Having Jurisdiction. Model GXLO sprinklers mustbe installed with the Reliable Model H sprinkler wrench. Any other type of wrench may damage the sprinkler. A leak tightjointshould be obtained with a torque of 14 to 20 lb-ft(19 to 27 N-m) for ¾-inch NPT and ISO 7-R¾ thread sprinklers. For ½-inch NPT and ISO 7-R½ thread sprinklers the recommended installation torque is 8 to 18 lb-ft(11 to 24 N-m). Do nottighten sprinklers over the maximum recommended installation torque, because itmay cause leakage or impairment of the sprinklers. Maintenance Model G XLO Sprinklers should be inspected and the sprinkler system maintained in accordance with NFPA 25. Do notclean sprinklers with soap and water, ammonia or any other cleaning fluids. Remove dustby using a softbrush or gentle vacuuming. Replace any sprinkler which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacementof damaged or operated sprinklers. Prior to installation, sprinklers should be maintained in the original cartons and packaging until used to minimize the potential for damage to sprinklers thatwould cause improper operation or non-operation. Ordering Information Specify: 1. Sprinkler: Model GXLO 2. Orientation/Deflector: [Upright] [Pendent] 3. Temperature Rating: [Ordinary, 165 F] [Intermediate, 212 F] [High 286 F] 4. Finishes: (See Finishes Chart) 5. Threads: [¾-inch NPT] [ISO 7-R¾] [½-inch NPT (Uprightonly)] [ISO 7-R½ Uprightonly] 6. Guard: [None] [D-6 (UprightcULus)] [D-7 (Upright FM)] [D-8 (PendentFM No Shield)] [D-9 (PendentFM with Shield)] Model H Sprinkler APPROVED Use only the Model H sprinkler wrench for sprinkler removal and installation. Any other type of wrench may damage the sprinkler. The equipmentpresented in this bulletin is to be installed in accordance with the latestpublished Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the mosthighly qualified and reputable sprinkler contractors located throughoutthe United States, Canada and foreign countries. Manufactured by Reliable Automatic Sprinkler Co., Inc. (800) Sales Offices (800) Sales Fax (914) Corporate Offices InternetAddress Recycled Paper Revision lines indicate updated or new data. EG. Printed in U.S.A. 06/15 P/N

13 Model F1FR56 Sprinkler Types Standard Spray Upright Standard Spray Pendent Conventional Upright/Pendent Vertical Sidewall Horizontal Sidewall Model F1FR56 Recessed Sprinkler Types Standard Spray Pendent Horizontal Sidewall Model F1FR56 Concealed Sprinkler Types Standard Spray Pendent Model F1FR42, F1FRXLH & F1FR28 Sprinkler Types Standard Spray Upright Standard Spray Pendent Model F1FR40 Sprinkler Types Standard Spray Pendent Model F1FR42, F1FR40, F1FRXLH & F1FR28 Recessed Sprinkler Types Standard Spray Pendent Model F1FR56LL & F1FR42LL NSF CertiÞed Low Lead Sprinkler Types Standard Spray Pendent with less than 0.25% Lead Content Listing & Approvals The following organizations provide Listings or Approvals for various Model F1FR series sprinklers. See the Design and Installation table in this Bulletin for information on specific listings and approvals applicable to each sprinkler. 1. Underwriters Laboratories Inc. and Certified for Canada (culus). 2. FM Approvals (FM) 3. Loss Prevention Certification Board (LPCB) 4. VdS Schadenverhütung GmbH (VdS) 5. NSF Certified to NSF/ANSi Standard 61 Annex G (NSF) 6. EC Certificate: 0786-CPD (RA1414), CPD (RA1425), 0786-CPD (RA1475) (EC) UL Listing Category Sprinklers, Automatic & Open (VNIV) Quick Response Sprinkler Bulletin 014Rev. N Model F1FR Series Quick Response Glass Bulb Sprinklers Upright Vertical Sidewall Recessed Horizontal Sidewall Pendent Horizontal Sidewall Concealed Pendent Conventional Recessed Pendent/F1/F2 Recessed Pendent/FP XLH Upright XLH Pendent XLH Recessed Pendent F1/F2 Product Description Reliable Model F1FR series sprinklers are quick-response automatic sprinklers with a glass bulb thermal element. Model F1FR series sprinklers are Standard Spray sprinklers, with the exception of the Model F1FR56 Conventional sprinkler which is an Old-style/Conventional sprinkler. APPROVED XLH Recessed Pendent FP The Model F1FR Series automatic sprinklers utilize a 3.0 mm frangible glass bulb. These sprinklers have demonstrated response times in laboratory tests which are five to ten times faster than standard response sprinklers. This quick response enables the Model F1FR Series sprinklers to apply water to a fire faster than standard-response sprinklers of the same temperature rating. The glass bulb consists of an accurately controlled amount of special fluid hermetically sealed inside a precisely manufactured glass capsule. This glass bulb is specially constructed to provide fast thermal response. Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York Bulletin 014Rev. N

14 At normal temperatures, the glass bulb contains the fluid in both the liquid and vapor phases. The vapor phase can be seen as a small bubble. As heat is applied, the liquid expands, forcing the bubble smaller and smaller as the liquid pressure increases. Continued heating forces the liquid to push out against the bulb, causing the glass to shatter, opening the waterway and allowing the deflector to distribute the discharging water. Model F1FR Series sprinklers provide a wide range of options where quick-response, glass bulb sprinklers are used: Pendent, recessed pendent, upright, horizontal sidewall, and vertical sidewall deß ectors K-factors of 2.8 (40 metric), 4.0 (57 metric), 4.2 (60 metric), and 5.6 (80 metric) Flush, recessed, and concealed installations See the Design and Installation Information table in this Bulletin for information on the approvals and availability of specific Model F1FR series sprinkler configurations. Model F1FR Recessed Pendent and Recessed Horizontal Sidewall sprinklers are required to be used with Reliable Model F1, F2, or FP recessed escutcheons. See the Recessed Escutcheon Data table in this Bulletin for listing and approval information with each specific Model F1FR series sprinkler. Model F1 and F2 recessed escutcheons, shown in Fig. 1 and 3, are a friction fit assembly allowing for 3/4-inch (19mm) and 1/2-inch (12.7mm) of adjustment, respectively. Model FP recessed escutcheons, shown in Fig. 2, provide a 1/2-inch (12.7mm) threaded adjustment. Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers are required to be used with Model CCP cover plates. A standard profile Model CCP cover plate is available that provides up to 1/2-inch (12.7mm) of cover plate adjustment. In addition, a low profile Model CCP cover plate is also available that provides up to 5/16-inch (8.0mm) of cover plate adjustment. See the Design and Installation Information and Listed and Approved Temperature Ratings tables in this Bulletin for further information on approved cover plate options. Application Model F1FR Series sprinklers are intended for use in accordance with NFPA 13, FM Property Loss Prevention Data Sheets, and the requirements of the Authority Having Jurisdiction. Care must be exercised that the k-factor, temperature rating, deflector style, and sprinkler type are in accordance with the requirements of the applicable design and installation standards. In addition, Model F1FR Series sprinklers must be used in accordance with their listings and approvals, as well as the information provided in this Bulletin. Installation Glass bulb sprinklers have orange bulb protectors or protective caps to minimize bulb damage during shipping, handling and installation. Reliable sprinkler installation wrenches are designed to install sprinklers with bulb protectors in place. Remove the bulb protector at the time when the sprinkler system is placed in service for fire protection. Removal of the bulb protector before this time may leave the bulb vulnerable to damage. Remove bulb protectors by undoing the clasp by hand. Do not use tools to remove bulb protectors. 2. APPROVED Model F1FR Series sprinklers must be installed with the Reliable sprinkler installation wrench identified in the Design and Installation Information table in this Bulletin. Any other wrench may damage the sprinkler. A leak tight sprinkler joint can be obtained with a torque of 8 to 18 lb-ft (11 to 24N-m). Do not tighten sprinklers over the maximum recommended installation torque. Exceeding the maximum recommended installation torque may cause leakage or impairment of the sprinkler. Recessed Sprinklers Model F1FR Series Recessed sprinklers are to be installed as shown in Fig. 1, Fig. 2, or Fig. 3, as applicable to the specific model being installed. The Recessed Escutcheon Data table in the Bulletin identifies the only recessed escutcheons that are permitted to be used with each Model F1FR Series Recessed sprinkler. The use of any other recessed escutcheon will void all approvals and negate all warranties. Concealed Sprinklers Model F1FR Series Concealed Pendent sprinklers are to be installed as shown in Fig. 4or Fig. 5, as applicable to the selected cover plate. Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers have a factory-installed Model CCP cup. A protective cap is installed at the factory that should remain on the sprinkler until the sprinkler is installed and should then be reinstalled on the sprinkler until the cover plate is installed. The concealed sprinkler assemblies are completed by the installation of a Model CCP push-on/thread-off cover plate assembly. The cover plate and sprinkler cup assemblies are joined using a cover plate skirt with flexible tabs for threaded engagement. A choice of two Model CCP cover plate assemblies provides either 1/2-inch (13mm) or 5/8-inch (8mm) of cover adjustment. Do not install Model F1FR Series Concealed Pendent sprinklers in ceilings which have positive pressure in the space above. Model F1FR Series Concealed Pendent sprinklers require a 2-5/8-inch (67mm) diameter hole to be cut in the ceiling. The Model RC1 wrench is used to engage the sprinkler wrenching surfaces and to install the sprinkler in the fitting. Remove the protective cap to install the sprinkler, then reinstall the protective cap until the cover plate is installed. When inserting or removing the wrench from the sprinkler/cup assembly, care should be taken to prevent damage to the sprinkler. Do not wrench any other part of the sprinkler/cup assembly. Installation is completed by removing the protective cap from the sprinkler and pushing the cover plate onto the cup. Final adjustment is made by hand turning the cover plate until the skirt flange makes full contact with the ceiling. Cover plate removal requires turning the cover plate in the counter clockwise direction. After installation, inspect all sprinklers to ensure that there is a gap between the cover plate and ceiling and that the four cup slots are open and free from any air flow impediment to the space above. Concealed cover plate/cup assemblies are listed only for use with specific sprinklers. The use of any concealed cover plate/cup assembly other than the Reliable Model CCP with Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers or the use of the Model CCP Concealed cover plate assembly on any sprinkler with which it is not specifically listed my prevent good fire protection and will void all guarantees, warranties, listings and approvals.

15 Model Design and Installation Information Nominal Nominal Nominal OriÞce K-factor Deßector/ Sprinkler Listings Installation Diameter Orientation Height Wrench SIN Approval and Notes Approvals US Metric inches mm inches mm F1FR /8 10 F1FR /8 10 F1FR /16 10 F1FR42LL /16 10 F1FRXLH (F1FR /16 10 with Pintle) F1FR /2 15 F1FR56LL /2 15 F1FR /2 15 F1FR /2 15 Pendent D RA1411 culus 2 Recessed Pendent GFR2 RA1411 culus 2 Upright D RA1421 culus 1,2 Pendent D RA1418 VdS Recessed Pendent GFR2 RA1418 VdS Pendent D RA1413 culus 2 Recessed Pendent GFR2 RA1413 culus 2 Upright D RA1423 culus 1,2 Pendent D RA1410 culus, NSF Recessed Pendent GFR2 RA1410 culus, NSF Pendent D RA1413 culus 2 Recessed Pendent GFR2 RA1413 culus 2 Upright D RA1423 culus 1,2 culus, FM, Pendent D RA1414 LPCB, VdS, EC 1,2,3,4 culus, FM, Recessed Pendent GFR2 RA1414 LPCB, VdS, EC 1,2,3,4 Concealed Pendent RC1 RA1414cULus,VdS,EC 5,6 culus, FM, Upright D RA1425 LPCB, VdS, EC 1,2,3,4 "Conventional D RA1475 LPCB, VdS, EC 4 (Pendent or Upright)" Pendent D RA1415 culus, NSF 1 Recessed Pendent GFR2 RA1415 culus, NSF Concealed Pendent RC1 RA1414 culus, NSF 6 Horizontal Sidewall D RA1435 culus, FM 1,2,3,7 Recessed Horizontal Sidewall GFR2 RA1435 culus, FM 8 Vertical Sidewall culus, FM, D RA1485 (Pendent or Upright) LPCB APPROVED Technical Data: Sensitivity: Quick-response Thread Size: 1/2-inch NPT standard; ISO 7-R1/2 optional Maximum Working Pressure: 175 psi (12 bar) - 100% Factory tested hydrostatically to 500 psi (34.5 bar) SIN RA1425, RA1414& RA1435 culus listed for 250 psi (17 bar) 1,2,3,9 (1) culus Listed Corrosion Resistant sprinkler when ordered with available Polyester coating. (2) culus Listed Corrosion Resistant sprinkler when ordered with available Electroless Nickel PTFE plating. (3) Available with FM approved Polyester coating in black or white. (4) Available with LPCB and VdS approved Polyester coating. (5) VdS and EC approvals of the F1FR56 Concealed Pendent sprinkler are for 155 F (68 C) temperature rated sprinklers only. VdS approved sprinklers must use Norbulb brand glass bulbs with the 1/2-inch (12.7mm) adjustment Model CCP cover plate only. (6) Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers must be used with Reliable Model CCP cover plates, available as either standard depth with 1/2-inch (12.7mm) of adjustment or low profile with 5/16-inch (8.0 mm) of adjustment. (7) culus Listing of the F1FR56 Horizontal Sidewall sprinkler is for Light and Ordinary Hazard occupancies only. FM Approval of the F1FR56 Horizontal Sidewall sprinkler is for Light Hazard occupancies only. (8) culus Listing and FM Approval of the F1FR56 Recessed Horizontal Sidewall sprinkler is for Light Hazard occupancies only. (9) The F1FR56 Vertical Sidewall sprinkler is listed and approved for use only in Light Hazard occupancies. Minimum to maximum deflector to ceiling distance shall be 4inches to 12 inches (102mm to 305mm). LPCB approval of the F1FR56 Vertical Sidewall sprinkler is for installation in the Pendent position only. 3.

16 Listed and Approved Temperature Ratings Model F1FR28 F1FR40 F1FR42 Deßector/ Orientation Pendent Ordinary Temp. ClassiÞcation 100 F (38 C) Max. Ambient Temp. 135 F (57 C) 1 5 F (68 C) Temp. Rating Temp. Rating Intermediate Temp. ClassiÞcation 150 F (65 C) Max. Ambient Temp. High Temp. ClassiÞcation 225 F (107 C) Max. Ambient Temp. 286 F (141 C) Temp. Rating 175 F (79 C) 200 F (93 C) Temp. Rating Temp. Rating Orange Bulb Red Bulb Yellow Bulb Green Bulb Blue Bulb culus Recessed Pendent culus -- Upright Pendent culus VdS Recessed Pendent VdS -- Pendent culus Recessed Pendent culus -- Upright culus Pendent -- culus, NSF -- F1FR42LL Recessed Pendent -- culus, NSF -- F1FRXLH F1FR56 F1FR56LL F1FR56 F1FR56 Pendent culus Recessed Pendent culus -- Upright Pendent culus culus, FM, LPCB, VdS, EC Recessed Pendent culus, FM, LPCB, VdS, EC -- Concealed Pendent* culus culus,vds,ec culus -- Upright Conventional (Pendent or Upright) culus, FM, LPCB, VdS, EC LPCB, VdS, EC Pendent -- culus, NSF -- Recessed Pendent -- culus, NSF -- Concealed Pendent* -- culus, NSF -- Horizontal Sidewall Recessed Horizontal Sidewall Vertical Sidewall (Pendent or Upright) culus, FM culus, FM -- culus, FM, LPCB APPROVED * Model F1FR56 Concealed Pendent and F1FR56LL Concealed Pendent sprinklers must be used with Reliable Model CCP cover plates. For Ordinary Temperature Classification sprinklers use a 135 F (57 C) temperature rated cover plate. For Intermediate Temperature Classification sprinklers use a 165 F (74 C) temperature rated cover plate. Recessed Escutcheon Data Model Deßector/ Orientation Listed and Approved Recessed Escutcheons Model F2 (Fig. 1 & 3) 1/2-inch (12.7mm) adjustment Model F1 (Fig. 1 & 3) 3/4-inch (19mm) adjustment Model FP (Fig. 2) 1/2-inch (12.7mm) adjustment F1FR28 Recessed Pendent culus culus culus RA1411 F1FR40 Recessed Pendent VdS VdS VdS RA1418 F1FR42 Recessed Pendent culus culus culus RA1413 F1FR42LL Recessed Pendent culus, NSF culus, NSF culus, NSF RA1410 F1FR42XLH Recessed Pendent culus culus culus RA1413 F1FR56 Recessed Pendent culus, LPCB, VdS, EC culus, FM, LPCB, VdS, EC culus, VdS, EC SIN RA1414 F1FR56LL Recessed Pendent culus, NSF culus, NSF culus, NSF RA1415 F1FR56 Recessed Horizontal Sidewall culus culus, FM culus RA

17 Fig. 1 Model F1FR56, F1FR56LL, F1FR42, F1FR40, F1FR42LL, F1FRXLH & F1FR28 Recessed Pendent sprinkler with Model F1 or F2 escutcheon Fig. 2 Model F1FR56, F1FR56LL, F1FR42, F1FR40, F1FR42LL, F1FRXLH & F1FR28 Recessed Pendent sprinkler with Model FP escutcheon 5.

18 Fig. 3 Model F1FR56 Recessed Horizontal Sidewall sprinkler with Model F1 or F2 escutcheon Fig. 4 Model F1FR56/F1FR56LL Concealed Pendent sprinkler with standard depth 1/2-inch (12.7mm) adjustment - Model CCP cover plate 6.

19 Fig. 5 - Model F1FR56/F1FR56LL Concealed Pendent sprinkler with low profile 5/16-inch (8.0mm) adjustment - Model CCP cover plate Maintenance The Model F1FR Series sprinklers should be inspected and the sprinkler system maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, ammonia or any other cleaning fluids. Remove dust by using a soft brush or gentle vacuuming. Replace any sprinkler which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or operated sprinklers. Finishes (1) Standard Finishes Sprinkler Escutcheon Cover plate (1) Bronze Brass Chrome Chrome Plated Chrome White Polyester Plated Coated (4)(5)(6) White Painted Special Application Finishes Sprinkler Escutcheon Cover plate (1) Electroless Nickel Electroless Nickel PTFE (7) PTFE Bright Brass Bright Brass (3) Bright Brass Black Plating Black Plated Black Plated Black Paint Black Paint (2)(6) Black Paint Off White Off White (2)(6) Off White Satin Chrome Chrome Dull Chrome Dull (1) Other finishes and colors are available on special order. Consult the factory for details. Custom color painted sprinklers may not retain their UL Corrosion resistance listing. Coverplate custom paint is semi-gloss, unless specified otherwise. (2) culus Listed only. (3) 200 F (93 C) maximum. (4) culus listed corrosion resistance applies to SIN Numbers RA1435 (HSW), RA1485(VSW), RA1425 (Upright), RA1414(Pendent) and RA1415 (Pendent) in standard black or white. Corrosion resistance in other polyester colors is available upon request. (5) FM Approvals finish as Polyester coated applies to SIN Number RA1414, RA1435 and RA1425 in standard black or white. (6) LPCB and VdS Approved finish applies only to RA1425, RA1414, RA1418 (VdS) and RA1475. (7) culus listed Corrosion Resistant 7. Frame: Deßector: Material Data DZR Brass, QM Brass, or Low Lead Brass CDA Alloy 220, 260, or 510 Load Screw\Pintle: CDA Alloy 360 or 5 4 Cup: Washer: Bulb: CDA Alloy 651 or 693 Nickel Alloy 40 or 360, coated with PTFE Adhesive Tape Glass Ordering Information Specify: 1. Sprinkler Model: [F1FR28][F1FR40][F1FR42] [F1FR42LL][F1FRXLH][F1FR56][F1FR56LL] 2. Sprinkler Deflector/Orientation: [Pendent][Recessed Pendent][Upright][Conventional][Horizontal Sidewall] [Recessed Horizontal Sidewall][Vertical Sidewall] 3. Sprinkler threads: [1/2-inch NPT][ISO 7-R1/2] 4. Sprinkler Temperature Rating: [135 F (57 C)][155 F (68 C)][175 F (79 C)][200 F (93 C)][286 F (141 C)] 5. Sprinkler Finish 6. Escutcheon Model: [F1][F2][FP] 7. Escutcheon Finish (where applicable) 8. Cover plate Model: [standard profile CCP 1/2-inch (12.7mm) adjustment][low profile CCP 5/16-inch (8.0mm) adjustment] 9. Cover plate Temperature Rating: [135 F (57 C) for use with Ordinary Temperature sprinklers][165 F (74 C) for use with Intermediate Temperature sprinklers] 10. Cover plate Finish Note: When Model F1FR Series Recessed sprinklers are ordered, the sprinklers and escutcheons are packaged separately.

20 Reliable...For Complete Protection Reliable offers a wide selection of sprinkler components. Following are some of the many precision-made Reliable products that guard life and property from fire around the clock. Automatic sprinklers Flush automatic sprinklers Recessed automatic sprinklers Concealed automatic sprinklers Adjustable automatic sprinklers Dry automatic sprinklers Intermediate level sprinklers Open sprinklers Spray nozzles Alarm valves Retarding chambers Dry pipe valves Accelerators for dry pipe valves Mechanical sprinkler alarms Electrical sprinkler alarm switches Water flow detectors Deluge valves Detector check valves Check valves Electrical system Sprinkler emergency cabinets Sprinkler wrenches Sprinkler escutcheons and guards Inspectors test connections Sight drains Ball drips and drum drips Control valve seals Air maintenance devices Air compressors Pressure gauges Identification signs Fire department connection The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries. Manufactured by Reliable Automatic Sprinkler Co., Inc. (800) Sales Offices (800) Sales Fax (914) Corporate Offices Internet Address Recycled Paper Revision lines indicate updated or new data. EG. Printed in U.S.A. 12 /15 P/N

21 VicFlex Style VS1 Dry Sprinkler APPROVED Models V3505, V3506, V3509, V3510, V3517, V PRODUCT DESCRIPTION Style: Pendent, Concealed Pendent, Horizontal Sidewall K Factor: 5.6 Imp./8.1 S.I. Forsystem design purposes, no equivalent length calculations are required. Nominal Orifice Size: ½"/13 mm Maximum Working Pressure: 175 psi/1200 kpa Factory Hydrostatic Test: 500 psi/3450 kpa Minimum Operating Pressure: 7 psi/48 kpa Connections: To branch line (inlet) via 1"/25 mm NPT or1" BSPT Minimum Bend Radius: 2"/51 mm Hazard Classifications: Light and Ordinary Hazard Maximum Numberof Bends: CERTIFICATION/LISTINGS Model APPROVALS/LISTINGS V3505 V3506 V3509 V3510 V3517 V3518 Orifice Size (inches) 1" 1" 1" 1" 1" 1" Orifice Size (mm) Nominal K Factor Imperial Nominal K Factor S.I Response Standard Quick Standard Quick Standard Quick Deflector Type Pendent Pendent Hor. SW Hor. SW Conc Pen Conc Pen Approved Temperature Ratings F /C 135/57 135/57 135/57 135/57 135/57 135/57 155/68 155/68 155/68 155/68 155/68 155/68 175/79 175/79 175/79 175/79 175/79 175/79 200/93 200/93 200/93 200/93 200/93 200/93 286/ / / /141 ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT. System No. Location Spec Section Paragraph Submitted By Date Approved Date victaulic.com Rev E Updated 04/ Victaulic Company. All rights reserved. 1

22 victaulic.com 3.0 MATERIAL SPECIFICATIONS Deflector: Brass Bulb: Glass with glycerin solution Bulb Nominal Diameter: Quick Response: 3.0 mm Standard Response: 5.0 mm Split spacer: Stainless Steel Load screw: Brass Pip Cap: Stainless Steel Spring Seal Assembly: PTFE-coated Beryllium Nickel and Stainless Steel Frame: Die cast brass Flexible Hose: 300-Series Stainless Steel Collar/Weld Fitting: 300-Series Stainless Steel Gasket Seal: Victaulic EPDM Isolation Ring: Nylon Hose Fittings: Carbon Steel, Zinc-Plated Inlet Fitting: Brass Outertube: 300-Series Stainless Steel Concealed cup: Carbon Steel, Zinc-plated Brackets: Carbon Steel, Zinc-plated 3.1 ACCESSORIES SPECIFICATIONS SprinklerFinishes: Standard: VC-250 White painted RAL Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 2

23 victaulic.com 4.0 DIMENSIONS Product Details and Optional Components Style VS1 Dry Sprinkler D B C L Sprinkler Length inches mm Overall Length (pendent) L inches mm Live Length B inches mm Add ½" to Overall Length and Outlet End Length forincreased length of sidewall deflector Outlet End Length C inches mm Maximum OD D inches mm Style VB1 Bracket 2.7"/ 68.6 mm 2.2"/ 54.6 mm* 1.0"/ 25.4 mm 4 x Ø.2"/ 5.1 mm 3.6"/ 92.1 mm 2.25"/ 57.2 mm *Note: Theoretical centerpoint of sprinklerin bracket. Style VB2 Bracket Recessed Pendent, Suspended Ceilings Style VB3 Bracket Concealed Pendent, Suspended Ceilings Item Description Item Description 1 24"/610 mm or 48"/1220 mm Square Bar 1 24"/610 mm or 48"/1220 mm Square Bar 2 Patented 1-Bee Center Bracket 2 Patented 1-Bee Center Bracket 3 End Bracket 3 End Bracket Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 3

24 victaulic.com 4.1 DIMENSIONS SprinklerFinishes: Dimensions and Mounting Conditions: NOTE: APPROVED Drawings are shown with 5/8" finished ceiling thickness. Adjustments to "B" and "C" dimensions will be required if finished ceiling thickness deviate from drawing. Recessed Pendent: 1"/ 25 mm R B 2¾"/ 70 mm C D Collar / "/ 16 mm 1"/25 mm Min. 1¾"/44 mm Max. Finished ceiling face Escutcheon 2 "/75 mm Take-out Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 7 5/8/ /8/ /8/ /8/ /8/ /8/320 C 4 3/119 Ceiling Hole Diameter"D" 2-2 3/8"/50-60mm NOTE: Dimensions are shown with 3" escutcheon at middle of height adjustment range Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 4

25 victaulic.com 4.2 DIMENSIONS Recessed Pendent Alternative Bracket Location: 2¾"/ 70 mm 1"/ 25 mm B R D Collar C C / "/ 16 mm 1"/25 mm Min. 1¾"/44 mm Max. Finished ceiling face Escutcheon 2 "/75 mm Take-out Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 7 5/8/ /8/ /8/ /8/ /8/ /8/320 C 2/50 Ceiling Hole Diameter"D" 2-2 3/8/50-60 NOTE: Dimensions are shown with 3" escutcheon at middle of height adjustment range Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 5

26 victaulic.com 4.3 DIMENSIONS Sleeve and Skirt Pendent: 2¾"/ 70 mm 1"/ 25 mm B R C D / "/ 16 mm Skirt Sleeve 2½"/64 mm Min. 4"/102 mm Max. Finished ceiling face 3 "/82 mm Hose Clearance Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 6 ½/163 7 ½/188 8 ½/213 9 ½/ ½/264 11½/290 C Ceiling Hole Diameter"D" 3 1/8/79 1 3/44-2 1/8/ DIMENSIONS Concealed Pendent: 1"/ 25 mm R B R 2 ¾"/ 70 mm C Cup D / "/ 16 mm Ceiling cover plate with ¼" total adjustment. Shown at mid-range of adjustment. 3 1/4/83 mm Finished ceiling face Hose Clearance Chart Dimension inches/mm Minimum Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 9 ½/ ½/ ½/ ½/ ½/ ½/368 C 61 /157 Ceiling Hole Diameter"D" 25/8/67-23 / Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 6

27 victaulic.com 4.5 DIMENSIONS Concealed Pendent Alternative Bracket Location: 2 ¾"/ 70 mm 1"/ 25 mm B R C Cup D / "/ 16mm Ceiling cover plate with ¼" total adjustment. Shown at mid-range of adjustment. 3 ¼"/83 mm Finished ceiling face Hose Clearance Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 91/8/ /8/ /8/ /8/ /8/ /8/358 C 31/89 Ceiling Hole Diameter"D" 25/8/67-23/ DIMENSIONS Sleeve and Skirt Sidewall: R B 1"/25 mm C Skirt Sleeve 3 "/79 mm Min. 3 "/98 mm Max. 3 "/82 mm 2.70"/69 mm D Finished ceiling face "/ 16 mm Hose Clearance Chart Dimension inches/mm Minimum Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 61/163 71/188 81/213 91/ / /290 C Ceiling Hole Diameter"D" 3 1/8/79 1 3/44-2 1/8/ Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 7

28 victaulic.com 4.7 DIMENSIONS Recessed Sidewall: 1"/25 mm R B C 2.70"/ 69 mm Collar 1 "/40mm Min. 2 "/59 mm Max. 2 "/59 mm Escutcheon D "/ 16 mm Finished ceiling face Hose Clearance Chart Dimension inches/mm Minimum Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 8/203 9/229 10/254 11/279 12/305 13/330 C 43/119 Ceiling Hole Diameter"D" 2/51-2 3/8/ DIMENSIONS Recessed Sidewall Alternative Bracket Location: B 1"/25 mm C 1 "/40 mm Min. 2 "/59 mm Max. R Collar 2.70"/69 mm D "/ 16 mm Escutcheon Finished ceiling face 2 "/59 mm Hose Clearance Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 B 8/203 9/229 10/254 11/279 12/305 13/330 C 2/51 Ceiling Hole Diameter"D" 2/51-2 3/8/ Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 8

29 victaulic.com 4.9 DIMENSIONS VB2 Recessed Pendent: R A See Chart Bracket Assembly Style VB2 / "/16 mm Typical ceiling tile 2.3"/58 mm 1.7"/43 mm Typical ceiling grid See note Finished ceiling face Ceiling escutcheon with ¾"/19 mm total adjustment. Shown at maximum recess 24"/610 mm or 48"/1219 mm on Center Hose Clearance Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 A 61/163 71/188 81/213 91/ / / DIMENSIONS VB3 Concealed Pendent: R A See Chart Bracket Assembly Style VB3 3.0"/76 mm / "/16 mm Typical ceiling tile 1.7"/43 mm Typical ceiling grid See note 24"/610 mm or 48/1219 " mm on Center Finished ceiling face Ceiling escutcheon with ¼"/0.54 mm total adjustment. Shown at maximum recess Hose Clearance Chart Dimension inches/mm Bend Radius "R" 2/50 3/75 4/100 5/125 6/150 7/175 A 75/8/193 85/8/218 95/8/ /8/ /8/ /8/ Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 9

30 victaulic.com 5.0 PERFORMANCE Freeze Protection Y Face of Fitting Unheated Space Face of Fitting Y Unheated Space Heated Space Heated Space Exterior Exterior NOTE Ambient Temperature Exposed to Discharge End of Sprinkler Exposed Minimum Ba rel Length "Y" inches mm F C 40 F/4 C 50 F/10 C 60 F/16 C Exposed minimum ba rel lengths are inclusive up to 30-mph/48-kph wind velocities. Maximum Allowable Numberof Bends SprinklerLength inches mm Maximum Allowable Numberof 90 Bends at 2"/51mm Bend Radius Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 10

31 victaulic.com 6.0 NOTIFICATIONS APPROVED WARNING It is the responsibility of the system designerto verify suitability of 300-Series stainless steel flexible hose foruse with the intended fluid media. The effect of chemical composition, ph level, operating temperature, chloride level, oxygen level, and flow rate on 300-Series stainless steel flexible hose must be evaluated by the material specifierto confirm system life will be acceptable forthe intended service. Failure to follow these instructions could cause product failure, resulting in serious personal injury and/orproperty damage. Important Installation Notes: 1. Should be installed only in accordance with NFPA 13 Standard forthe the Installation of SprinklerSystems. 2. Install and tighten hexagonal boss at inlet of sprinklerfitting only. 3. DO NOT install the Victaulic VicFlex Style VS1 Dry Sprinkler s inlet into any fitting that interferes with thread penetration. Use a sample fitting to confirm properengagement. To ensure unobstructed flow during operation, the Victaulic VicFlex Style VS1 Dry Sprinklermust be installed into a fitting that will prevent waterand debris from accumulating at the dry sprinkler s inlet. 4. Do not remove deflectororinlet end of sprinkler. FOR DRY SYSTEMS ONLY: The Style VS1 Dry Sprinkler s inlet MUST be installed only into the outlet of a cast ormalleable iron tee that meets the dimensional requirements of ANSI B16.3 and ANSI B16.4, Class 125 and Class 150. Use a sample fitting to confirm properengagement. Style VS1 Dry Sprinklers in dry systems must be installed with a continuous downward slope along its entire length from the branch line fitting to the sprinkler. No localized low points shall be present along the length of the Style VS1 Dry Sprinkler. Style VS1 Dry Sprinklers are not permitted to be installed into the top of the branch line piping. Style VS1 Dry Sprinklers must be installed into the side orfrom the bottom of the branch line piping. FOR WET SYSTEMS ONLY: Style VS1 Dry Sprinklers in wet systems, installed where a portion extends into an unconditioned space, must be installed with a continuous downward slope along the entire exposed length from the inside wall to the sprinkler. No localized low points shall be present along the exposed length of the sprinkler. Inlet Continuous Downward Slope Inlet Continuous Downward Slope Heated Space Unheated Space Heated Space Unheated Space Outlet ACCEPTABLE PITCH Outlet ACCEPTABLE PITCH Inlet Inlet Low Point Low Point Heated Space Unheated Space Heated Space Unheated Space Outlet UNACCEPTABLE PITCH Outlet UNACCEPTABLE PITCH Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 11

32 7.0 REFERENCE MATERIALS ONE BEND TWO BENDS APPROVED victaulic.com Minimum bend radius 2X Minimum bend radius 2X Minimum bend radius Minimum bend radius 90 OR OR Minimum bend radius Minimum bend radius Minimum bend radius Minimum bend radius Minimum bend radius NOTE For out-of-plane (three-dimensional) bends, care must be taken to avoid imparting torsional stress on the sprinkler. User Responsibility for Product Selection and Suitability Each user bears final responsibility for making a determination as to the suitability of Victaulic products for a particular end-use application, in accordance with industry standards and project specifications, and the applicable building codes and related regulations as well as Victaulic performance, maintenance, safety, and warning instructions. Nothing in this or any other document, nor any verbal recommendation, advice, or opinion from any Victaulic employee, shall be deemed to alter, vary, supersede, or waive any provision of Victaulic Company's standard conditions of sale, installation guide, or this disclaimer. Intellectual Property Rights No statement contained herein concerning a possible or suggested use of any material, product, service, or design is intended, or should be constructed, to grant any license under any patent or other intellectual property right of Victaulic or any of its subsidaries or affiliates covering such use or design, or as a recommendation for the use of such material, product, service, or design in the infringement of any patent or other intellectual property right. The terms Patented or Patent Pending refer to design or utility patents or patent applications for articles and/or methods of use in the United States and/or other countries. Note This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. Installation Reference should always be made to the Victaulic installation handbook or installation instructions of the product you are installing. Handbooks are included with each shipment of Victaulic products, providing complete installation and assembly data, and are available in PDF format on our website at Warranty Refer to the Warranty section of the current Price List or contact Victaulic for details. Trademarks Victaulic and all other Victaulic marks are the trademarks or registered trademarks of Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries Rev E Updated 04/ Victaulic Company. All rights reserved. victaulic.com 12

33 FIG Flexible Coupling COUPLINGS APPROVED The Gruvlok Fig Coupling forms a flexible grooved end pipe jointconnection with the versatility for a wide range of applications. Services include mechanical and plumbing, process piping, mining and oil field piping, and many others. The coupling design supplies optimum strength for working pressures to 1000 PSl (69 bar) withoutexcessive casting weight. The flexible design eases pipe and equipmentinstallation while providing the designed-in benefitof reducing pipeline noise and vibration transmission withou the addition of special components. To ease coupling handling and assembly and to assure consistentquality, sizes 1" through 14" couplings have two 180 segmenthousings, 16" have three 120 segmenthousings, and 18" through 24" sizes have four 90 segmenthousings, while the 28" O.D. and 30" O.D. couplings have six 60 segmenthousings. The 28" O.D. and 30" O.D. are weld-ring couplings. For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. MATERIAL SPECIFICATIONS BOLTS: SAE J429, Grade 5, Zinc Electroplated ISO 898-1, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip HEAVY HEX NUTS: ASTM A563, Grade A, Zinc Electroplated ISO 898-2, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip STAINLESS STEEL BOLTS & NUTS: 304SS bolts and nuts are available as a standard option. (316SS are available for special order). HOUSING: Ductile Iron conforming to ASTM A 536, Grade COATINGS: q Rustinhibiting paint Color: ORANGE (standard) q HotDipped Zinc Galvanized (optional) q Other Colors Available (IE: RAL3000 and RAL9000) For other Coating requirements contactan Anvil Representative. GASKETS: Materials Properties as designated in accordance with ASTM D 2000 q Grade EP EPDM (Green and Red color code) -40 F to 250 F (Service Temperature Range)(-40 C to 121 C) Recommended for water service, diluted acids, alkalies solutions, oil-free air and many other chemical services. NOT FOR USE IN PETROLEUM APPLICATIONS. For hotwater applications the use of Gruvlok Extreme Temperature lubricantis recommended. NSF-61 Certified for cold and hotwater applications up through 12". q Grade T Nitrile (Orange color code) -20 F to 180 F (Service Temperature Range)(-29 C to 82 C) Recommended for petroleum applications. Air with oil vapors and vegetable and mineral oils. NOT FOR USE IN HOT WATER OR HOT AIR q Grade O Fluoro-Elastomer (Blue color code) Size Range: 1" - 12" (C style only) 20 F to 300 F (Service Temperature Range)(-29 C to 149 C) Recommended for high temperature resistance to oxidizing acids, petroleum oils, hydraulic fluids, halogenated hydrocarbons and lubricants. q Grade L Silicone (Red color code) Size Range: 1" - 12" (C style only) -40 F to 350 F (Service Temperature Range)(-40 C to 177 C) Recommended for dry, hotair and some high temperature chemical services. Contactan Anvil Representative for availability. GASKET TYPE: q C Style (1" - 30") q Flush Gap (1" - 24") LUBRICATION: q Standard q Gruvlok Xtreme TM (Do Notuse with Grade L ) WORKING PRESSURE, END LOAD, PIPE END SEPARATION & DEFLECTION FROM CENTER LINE: Based on standard wall steel pipe with cutor roll grooves in accordance with Gruvlok specifications. See technical data section for design factors. Fig with Standard Gasket Fig with Flush Gap Gasket Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: GL-7.16 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

34 COUPLINGS FIG Flexible Coupling Y Z Y APPROVED Z Y Z X X X Nominal Size SIZES 1" - 14" SIZES 16" - 24" SIZES 28" - 30" Max.Work. Max. End O.D. Pressure Load Range of Pipe End Separation FIGURE 7001 FLEXIBLE COUPLING Deflection from C L Coupling Dimensions BoltDimensions* Specified Torque Approx. Wt. Ea. Per Coupling of Pipe X Y Z Qty. Size Min. Max. In./DN(mm) In./mm PSI/bar Lbs./kN In./mm Degrees( )-Minutes(') In./ft-mm/m In./mm In./mm In./mm In./mm Ft.-Lbs/N-m Lbs./kg , ' x M10 x , ' x M10 x , ' x M10 x , ' x M12 x , ' x M12 x O.D , ' x M12 x , ' x M12 x , ' x M16 x , ' x M16 x , ' x M20 x O.D , ' x M20 x , ' x M20 x , ' x M22 x , ' x M22 x , ' x M22 x , ' x M22 x , ' x * , ' x * , ' x * , ' x * " I.D , ' x * " I.D , ' x * NOTES: Range of Pipe End Separation and Angular Deflection values are for roll grooved pipe and may be doubled for cut groove pipe. See the Technical Data Section of the Gruvlok Catalog. For Misalignment, Deflection and Curve Layout Calculations, refer to the Technical Data Section of the Gruvlok Catalog. Maximum Working Pressure Rating is for schedule 40 steel pipe. For light wall, stainless steel, aluminum and ISO pipe pressure ratings, please refer to the technical data section. For additional details see Coupling Data Chart Notes in the Introduction Section of the Gruvlok Catalog. * Available in ANSI or metric bolt sizes only as indicated. For additional Bolt Torque information, see the Technical Data Section of the Gruvlok Catalog. See Installation & Assembly directions on next page. Not for use in copper systems. GL-7.16

35 FIG Flexible Coupling COUPLINGS APPROVED 1CHECK & LUBRICATE GASKET Check gasketto be sure itis compatible for the intended service. Applya thin coating of Gruvlok lubricantto the exterior surface and sealing lips of the gasket. Be careful thatforeign particles do notadhere to lubricated surfaces. GASKET INSTALLATION Slip the 2 gasketover the pipe end making sure the gasketlip does notoverhang the pipe end. On couplings 10" and larger itmay be easier to turn the gasket inside outthen lubricate and slide the gasketover the pipe end as shown. ALIGNMENT After aligning the two 3 pipe ends, pull the gasketinto position centering itbetween the grooves on each should notextend into the groove on either pipe. On couplings 10" and larger, flip or roll the gasketinto centered position. HOUSINGS Place the coupling 4 housing halves over the gasketmaking sure the housing keys engage the grooves. Insert bolts and turn nuts finger tight. TIGHTENNUTS Tighten the nuts 5 alternately and equally to the specified bolt torque. The housing boltpads mustmake metalto-metal contact. CAUTION: Uneven tightening may cause the gasketto pinch. ASSEMBLYIS COMPLETE 6 Visually inspectthe pipe jointto assure the coupling keys are fully engaged in the pipe grooves and the boltpads are in firm even metalto-metal contacton both sides of the coupling. NOTE: The housings for sizes 16 and larger are castin four or more segments. TO INSTALL: Loosely pre-assemble the segments into two Housing Halves making sure thatthe alignmenttang(s) and slot(s) on the boltpad(s) are properly mated. Install the Housing Halves as shown in steps 4 & 5. The coupling is properly installed when all bolt pads are firmly together - Metal-to-Metal. CAUTION: Proper torquing of coupling bolts is required to obtain specified performance. Over torquing the bolts may resultin damage to the boltand/or casting which could resultin pipe jointseparation. Under torquing the bolts may resultin lower pressure retention capabilities, lower bend load capabilities, jointleakage and pipe jointseparation. Pipe jointseparation may resultin significantproperty damage and serious injury. GL-3.14

36 FIG. C-4 Rigid Coupling The C-4 Rigid Coupling is our standard coupling and is designed for rigid piping applications. The C-4 is specially designed to provide a rigid, locked-in pipe connection to meet the specific demands of rigid design steel pipe. For the latest UL/ULC listed, LPCB, VdS and FM Approved pressure ratings versus pipe schedule, see or contact your local Anvil Representative. VdS For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. LPS 1219: Issue 3.1 Cert/LPCB ref. 519a/02 MATERIAL SPECIFICATIONS HOUSING: Ductile Iron conforming to ASTM A-536, Grade BOLTS: SAEJ429, Grade 5, Zinc Electroplated ISO 898-1, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip HEAVY HEX NUTS: ASTM A563, Grade A, Zinc Electroplated ISO 898-2, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip COATINGS: q Rust inhibiting paint Color: ORANGE(standard) q Hot Dipped Zinc Galvanized (optional) q Other available options: Example: RAL3000 or RAL9000 Series For other coating requirements contact an Anvil Representative. GASKETS: Materials Properties as designated in accordance with ASTM D q Pre-Lubricated Grade E EPDM, Type A Gasket (Violet color code) -40 F to 150 F (Service Temperature Range)(-40 C to 65 C) Recommended for wet and dry (oil free air) pipe fire protection sprinkler systems. For dry pipe systems and freezer applications, Gruvlok Xtreme Lubricant is required. GASKET TYPE: q Standard C Style q Flush Gap LUBRICATION: q Standard Gruvlok q Gruvlok Xtreme required for dry pipe systems and freezer applications. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

37 FIG. C-4 Rigid Coupling Y Z X Nominal Size Pipe O.D. Max. Working Pressures Max. Range of Pipe End LoadEnd Separation C-4 RIGID COUPLING CouplingDimensions Coupling Bolts Specified Torque Approx. Wt. Ea. X Y Z Qty. Size Min. Max. In./DN(mm) In./mm PSI/bar Lbs./kN In./mm In./mm In./mm In./mm In./mm Ft.-Lbs./N-m Lbs./Kg x M10 x x M10 x x M10 x , x M10 x , x M10 x O.D , x M10 x , x M10 x , x M10 x O.D , x M12 x , x M12 x O.D , x M12 x , x M12 x , x M16 x , x M22 x , x M22 x Range of Pipe End Seperation values are for roll grooved pipe and may be doubled for cut groove pipe. 1. Working pressure and/or end load are total allowable, based on standard weight steel pipe, roll or cut grooved. 2. One time field test pressure may be increased to 1.5 times the figures listed above. For additional Bolt Torque information see Technical Data Section. s Working Pressure Ratings are for reference only and based on Sch. 10 and Sch. 40 pipe. For the latest UL/ULC, FM, VdS and LPCB pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. Other sizes available, contact an Anvil Representative. For dry pipe systems and freezer applications lubrication of the gasket is required, Gruvlok Xtreme Lubricant is required. FP-10.16

38 FIG. C-4 Rigid Coupling Step 1 Step 2 Step 3 The instructions are based on pipe grooved in accordance with SPF grooving specifications. Check pipe ends for proper groove dimensions and to assure that the pipe ends are free of indentations and projections which would prevent proper sealing. ALWAYS USE A GRUVLOK SPF/ANVIL LUBRICANT FOR PROPER COUPLING ASSEMBLY. Thorough lubrication of the external surface of the gasket is essential to prevent pinching and possible damage to the gasket. For temperatures above 150 F (65 C) and below 32 F (0 C) use Gruvlok SPF/Anvil Xtreme Lubricant and lubricate all gasket surfaces, internal and external. See Gruvlok SPF/Anvil Lubricants in the Technical Data section of the Anvil SPF catalog for additional important information. 1Check and lubricate gasket Check gasket to be sure it is compatible for the intended service. Apply a thin coating of Gruvlok SPF/Anvil Xtreme Lubricant to the outside and sealing lips of the gasket. Be careful that foreign particles do not adhere to lubricated surfaces. Step 4 2Gasket installation Slip the gasket over the one pipe, making sure the gasket lip does not overhang the pipe end. Step 5 3Alignment After aligningthe two pipe ends together, pull the gasket into position, centering it between the grooves on each pipe. The gasket should not extend into the groove on either pipe. Step 6 4Housings Remove one nut and bolt and loosen the other nut. Place one housing over the gasket, making sure the housing keys fit into the pipe grooves. Swing the other housing over the gasket and into the grooves on both pipes, making sure the tongue and recess of each housing is properly mated. Re-insert the bolt and run-up both nuts finger tight. 5Tighten nuts Securely tighten nuts alternately and equally to the specified bolt torque, keeping the gaps at the bolt pads evenly spaced. Caution: Uneven tightening may cause the gasket to pinch. Gasket should not be visible between segments after bolts are tightened. Specified Bolt Torque Specified bolt torque is for the oval neck track bolts used on SPF couplings. The nuts must be tightened alternately and evenly until fully tightened. Caution: Proper torquing of coupling bolts is required to obtain specified performance. Over torquing the bolts mayresult in damage to the bolt and/ or casting which could result in pipe joint separation. Under torquing the bolts may result in lower pressure retention capabilities, lower bend load capabilities, joint leakage and pipe joint separation. Pipe joint separation may result in significant property damage and serious injury. 6Assemblyis complete Visually inspect the pipe joint to assure the coupling keys are fully engaged in the pipe grooves. The bolt pads are to have equal gaps on each side of the coupling. ANSI Metric Specified Bolt TorqueSpecified Bolt Torque Bolt Size Wrench Size Specified Bolt Torque* Bolt Size Wrench Size Specified Bolt Torque* In. In. Ft.-Lbs mm mm N-M 3 /8 11 / M /2 7 / M /8 1 1 / M /8 1 7 / M * Non-lubricated bolt torque * Non-lubricated bolt torque FP-10.16

39 FIG. E-1 90 Elbow O.D. C to E Nominal Size E-1 90 ELBOW O.D. Max. Working Pressure Center to End Approx. Wt. Ea. In./DN(mm) In./mm PSI/bar In./mm Lbs./Kg O.D O.D O.D MATERIAL SPECIFICATIONS CAST FITTINGS: Ductile Iron conforming to ASTM A-536 VdS For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. FINISH: q Rust inhibiting paint Color:ORANGE (standard) or q Hot Dipped Zinc Galvanized conforming to ASTM A-153 (optional) q Other available options:example:ral3000 or RAL9000 Series Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP-4.12 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

40 FIG. T-1 Straight Tee O.D. C to E C to E Nominal Size T-1 STRAIGHT TEE O.D. Center to End Approx. Wt. Ea. In./DN(mm) In./mm In./mm Lbs./Kg MATERIAL SPECIFICATIONS CAST FITTINGS: Ductile Iron conforming to ASTM A-536 VdS For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. COATINGS: q Rust inhibiting paint Color:ORANGE (standard) or q Hot Dipped Zinc Galvanized conforming to ASTM A-153 (optional) q Other available options:example:ral3000 or RAL9000 Series Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP-4.12 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

41 FIG. SK-1 Cap E to E SK-1 GROOVED CAP Nominal Size O.D. End to End Approx. Wt. Ea. In./DN(mm) In./mm In./mm Lbs./Kg O.D O.D * * *Supplied as Style K-1 only. MATERIAL SPECIFICATIONS CAST FITTINGS: Ductile Iron conforming to ASTM-A536 VdS For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. COATINGS: q Rust inhibiting paint Color:ORANGE (standard) or q Hot Dipped Zinc Galvanized conforming to ASTM A-153 (optional) q Other available options:example:ral3000 or RAL9000 Series Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP-4.12 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

42 FIG. MT-2 Grooved Mechanical Branch Tee Mechanical branch connections for reducing branch outlets without welding. The MT-2 is a bolted saddle type fitting with grooved outlets. Design assures superior sealing, full pipe support, excellent stability and easy installation. For the latest UL/ULC listed, LPCB, VdS and FM Approved pressure ratings versus pipe schedule, see or contact your local Anvil Representative. VdS For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. LPS 1219: Issue 3.1 Cert/LPCB ref. 519a/09 MATERIAL SPECIFICATIONS HOUSING: Ductile Iron conforming to ASTM A-536, Grade BOLTS: SAEJ429, Grade 5, Zinc Electroplated ISO 898-1, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip HEAVY HEX NUTS: ASTM A563, Grade A, Zinc Electroplated ISO 898-2, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip GASKETS: Materials Properties as designated in accordance with ASTM D q Grade E EPDM (Green color code) -40 F to 230 F (Service Temperature Range)(-40 C to 110 C) Recommended for water service, diluted acids, alkalies solutions, oil-free air and many chemical services. NOT FOR USEIN PETROLEUM APPLICATIONS. COATINGS: q Rust inhibiting paint Color: ORANGE(standard) q Hot Dipped Zinc Galvanized (optional) q Other available options: Example: RAL3000 or RAL9000 Series For other coating requirements contact an Anvil Representative. LUBRICATION: q Standard Gruvlok q Gruvlok Xtreme required for dry pipe systems and freezer applications. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

43 FIG. MT-2 Grooved Mechanical Branch Tee Y Y Z V V W U For dry pipe systems and freezer applications lubrication of the gasket is required, Gruvlok Xtreme Lubricant is required. Nominal Size MT-2 GROOVED MECHANICAL BRANCH TEE (TABLE CONTINUES TO NEXT PAGE) O.D. Hole Dimensions Max. Dimensions Working Min. Diameter Max. Diameter Pressures U V W Y Z Bolt Size Approx. Wt. Ea. In./DN(mm) In./mm In./mm In./mm PSI/bar In./mm In./mm In./mm In./mm In./mm In./mm Lbs./Kg 3 O.D. x x x x x O.D. x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 3 O.D x x x x x x x x x x x x x x x x x x x x x x x x O.D. x x x x x O.D. x 3 O.D x x x x O.D. x x x x x x x x x x x x x x x x x x x x x x x x x x 3 O.D x / x x x M16 x x x x x x M16 x All sizes may be used as mechanical crosses. Outlet branch is machined per standard cut groove specification. s Working Pressure Ratings are for reference only and based on Sch. 10 and Sch. 40 pipe. For the latest UL/ULC, FM, VdS and LPCB pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. FP-10.16

44 FIG. MT-2 Grooved Mechanical Branch Tee Y Y Z V V W U For dry pipe systems and freezer applications lubrication of the gasket is required, Gruvlok Xtreme Lubricant is required. Nominal Size MT-2 GROOVED MECHANICAL BRANCH TEE (CONTINUED FROM PREVIOUS PAGE) O.D. Hole Dimensions Max. Dimensions Working Min. Diameter Max. Diameter Pressures U V W Y Z Bolt Size Approx. Wt. Ea. In./DN(mm) In./mm In./mm In./mm PSI/bar In./mm In./mm In./mm In./mm In./mm In./mm Lbs./Kg 6 x x x x x M16 x O.D. x x x x x O.D. x x x x x O.D. x x x x x O.D. x 3 O.D x x x x O.D. x x x x x O.D. x x x x x x x x x x x x x x x x 3 O.D x x x x x x x x x x x x x x All sizes may be used as mechanical crosses. Outlet branch is machined per standard cut groove specification. s Working Pressure Ratings are for reference only and based on Sch. 10 and Sch. 40 pipe. For the latest UL/ULC, FM, VdS and LPCB pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. FP-10.16

45 FIG. MT-2 Grooved Mechanical Branch Tee ALWAYS USE A GRUVLOK SPF/ANVIL LUBRICANT FOR PROPER COUPLING ASSEMBLY. Thorough lubrication of the gasket is essential to assist the gasket into the proper sealing position. 1Pipe preparation Cut the appropriate size hole in the pipe and remove any burrs. Be sure to remove the slug from inside the pipe. Clean the gasket sealing surface within 5 /8" (16mm) of the hole and visually inspect the sealing surface for defects that may prevent proper sealing of the gasket. BRANCH SIZE HOLE SAW SIZE FLOW DATA Inches (mm) Inches + 1 /8, -0 (mm +3, -0) (see note) 1 1 4, , OD Note: Flow Data is expressed as Feet/Meters of Schedule 40 steel outlet pipe with a "Hazen- Williams coefficient of friction value of 120". Step 2 2Check and lubricate gasket Check the gasket to be sure it is compatible for the intended service. Apply a thin layer of Gruvlok SPF/Anvil lubricant to the back surface of the gasket. Be careful that foreign particles do not adhere to the lubricated surfaces. Insert the gasket back into the outlet housing making sure the tabs in the gasket line up with the tab recesses in the housing. Step 3 3Gasket installation Lubricate the exposed surface of the gasket. Align the outlet housing over the pipe hole making sure that the locating collar is in the pipe hole. Step 4 Step 5 Step 6 4Alignment Alignthe strap around the pipe, insert Tighten nuts Alternately and evenly tighten the nuts the bolts and tighten the nuts finger tight.5to the specified bolt torque. 6 Assembly is complete Specified Bolt Torque Specified bolt torque is for the oval neck track bolts used on SPF grooved mechanical branches. The nuts must be tightened alternately and evenly until fully tightened. Caution: Proper torquing of mechanical branch bolts is required to obtain specified performance. Over torquing the bolts may result in damage to the bolt and/or casting which could result in pipe joint separation. Under torquing the bolts may result in lower pressure retention capabilities, lower bend load capabilities, joint leakage and pipe joint separation. Pipe joint separation may result in significant property damage and serious injury. ANSI Metric Specified Bolt TorqueSpecified Bolt Torque Bolt Size Wrench Size Specified Bolt Torque* Bolt Size Wrench Size Specified Bolt Torque* In. In. Ft.-Lbs 1 /2 7 / /8 1 1 / /4 1 1 / mm mm N-M M M M * Non-lubricated bolt torque * Non-lubricated bolt torque FP-10.16

46 FIG. MT-1 Threaded Mechanical Branch Tee Mechanical branch connections are used for reducing branch outlets without welding. The MT-1 is a bolted saddle type fitting with NPT female threaded outlets. Design assures superior sealing, full pipe support, excellent stability and easy installation. For the latest UL/ULC listed, LPCB, VdS and FM Approved pressure ratings versus pipe schedule, see or contact your local Anvil Representative. For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. MATERIAL SPECIFICATIONS HOUSING: Ductile Iron conforming to ASTM A-536, Grade BOLTS: SAEJ429, Grade 5, Zinc Electroplated ISO 898-1, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip HEAVY HEX NUTS: ASTM A563, Grade A, Zinc Electroplated ISO 898-2, Class 8.8, Zinc Electroplated followed by a Yellow Chromate Dip GASKETS: Materials Properties as designated in accordance with ASTM D q Grade E EPDM (Green color code) -40 F to 230 F (Service Temperature Range)(-40 C to 110 C) Recommended for water service, diluted acids, alkalies solutions, oil-free air and many chemical services. NOT FOR USEIN PETROLEUM APPLICATIONS. COATINGS: q Rust inhibiting paint Color: ORANGE(standard) q Hot Dipped Zinc Galvanized (optional) q Other available options: Example: RAL3000 or RAL9000 Series For other coating requirements contact an Anvil Representative. LUBRICATION: q Standard Gruvlok q Gruvlok Xtreme required for dry pipe systems and freezer applications. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

47 FIG. MT-1 Threaded Mechanical Branch Tee MT-1 THREADED MECHANICAL BRANCH TEE Hole Dimensions Max. Dimensions Nominal Bolt Approx. O.D. Working Size V Min. Diameter Max. Diameter Size Wt. Ea. Pressures T W Y Z Threaded In./DN(mm) In./mm In./mm In./mm PSI/bar In./mm In./mm In./mm In./mm In./mm In./mm Lbs./Kg 2 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x All sizes may be used as mechanical crosses. Threads are NPT per ANSI/ASME B s Working Pressure Ratings are for reference only and based on Sch. 10 and Sch. 40 pipe. For the latest UL/ULC, FM, VdS and LPCB pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. For dry pipe systems and freezer applications lubrication of the gasket is required, Gruvlok Xtreme Lubricant is required. FP-10.16

48 FIG. MT-1 & MT-8 Threaded Mechanical Branch Tees ALWAYS USE A GRUVLOK SPF/ANVIL LUBRICANT FOR PROPER COUPLING ASSEMBLY. Thorough lubrication of the gasket is essential to assist the gasket into the proper sealing position. 1Pipe preparation Cut the appropriate size hole in the pipe and remove any burrs. Be sure to remove the slug from inside the pipe. Clean the gasket sealing surface within 5 /8"(16mm) of the hole and visually inspect the sealing surface for defects that may prevent proper sealing of the gasket. BRANCH SIZE (2"run) 32 (50mm run) (2 1 /2"-6" run) 32 (65-150mm run) (2"run) 40 (50mm run) (2 1 /2"-6" run) 40 (65-150mm run) O.D HOLE SAW SIZE FLOW DATA MT-1 MT-8 Inches (mm) Inches + 1 /8,-0(mm +3, -0) (see note) Step 2 2Check and lubricate gasket Check the gasket to be sure it is compatible for the intended service. Apply a thin layer of Gruvlok SPF/Anvil lubricant to the back surface of the gasket. Be careful that foreign particles do not adhere to the lubricated surfaces. Insert the gasket back into the outlet housing making sure the tabs in the gasket line up with the tab recesses in the housing. Note: Flow Data is expressed as Feet/Meters of Schedule 40 steel outlet pipe with a "Hazen- Williams coefficient of friction value of 120". Step 3 3Gasket installation Lubricate the exposed surface of the gasket. Align the outlet housing over the pipe hole making sure that the locating collar is in the pipe hole. Step 4 Step 5 Step 6 4Alignment Align the straparound the pipe, insert the bolts and tighten the nuts finger tight.5 Tightennuts Alternately and evenly tighten the nuts to the specified bolt torque. Specified Bolt Torque Specified bolt torque is for the oval neck track bolts used on SPF threaded mechanical branches. The nuts must be tightened alternately and evenly until fully tightened. Caution: Proper torquing of mechanical branch bolts is required to obtain specified performance. Over torquing the bolts may result in damage to the bolt and/or casting which could result in pipe joint separation. Under torquing the bolts may result in lower pressure retention capabilities, lower bend load capabilities, joint leakage and pipe joint separation. Pipe joint separation may result in significant property damage and serious injury. Assembly is complete 6 ANSI Metric Specified Bolt TorqueSpecified Bolt Torque Bolt Size Wrench Size Specified Bolt Torque* Bolt Size Wrench Size Specified Bolt Torque* In. In. Ft.-Lbs mm mm N-M 3 /8 11 / M /2 7 / M /8 1 1 / M /4 1 1 / M * Non-lubricated bolt torque * Non-lubricated bolt torque FP-10.16

49 FIG. MT-30 Threaded Mechanical Branch Tee The MT-30 mechanical tee serves the same function as the MT-1 and MT-8, but uses a steel electro-plated u-bolt to save space and for easier installation in tight places.the MT-30 is ideal for direct connections with sprinkler heads and drop nipples. The MT-90 is the BSPT equivalent. For the latest UL/ULC listed, LPCB, VdS and FM Approved pressure ratings versus pipe schedule, see or contact your local Anvil Representative. For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. MATERIAL SPECIFICATIONS HOUSING: Ductile Iron conforming to ASTM A-536, Grade U-BOLT & NUTS: U-bolt is carbon steel SAE J429 Gr. 2, zinc plated complete with hex flanged lock nuts conforming to ASTM A-563 Gr. A or B of SAE J995 Gr. 2. THREADS: NPT per ANSI/ASME B COATINGS: q Zinc Electroplated q Other available options: Example: RAL3000 or RAL9000 Series GASKETS: Materials Properties as designated in accordance with ASTM D q Grade E EPDM (Green color code) -40 F to 230 F (Service Temperature Range)(-40 C to 110 C) Recommended for water service, diluted acids, alkalies solutions, oil-free air and many chemical services not involving hydrocarbons, oils or gases. NOT FOR USE WITH HYDROCARBONS. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

50 FIG. MT-30 Threaded Mechanical Branch Tee Nominal Size O.D. MT-30 THREADED MECHANICAL BRANCH TEE Hole Dimensions Max. Dimensions Working Min. Diameter Max. Diameter Pressures A B C T Take-out Approx. Wt. Ea. In./DN(mm) In./mm In./mm In./mm PSI/bar In./mm In./mm In./mm In./mm Lbs./Kg x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x BSP equivalent is available as a MT-90. s Working Pressure Ratings are for reference only and based on Sch. 10 and Sch. 40 pipe. For the latest UL/ULC, FM, VdS and LPCB pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. Note: Tighten nuts alternately to a recommended torque of ft.-lbs. (25-30 Nm) on pipe wall less than schedule 10 (Din 2440) or ft.-lbs. (31-37 Nm) on pipe walls schedule 10 (DIN 2440) and above. For dry pipe systems and freezer applications lubrication of the gasket is required, Gruvlok Xtreme Lubricant is required. FP-10.16

51 FIG. MT-30 & MT-90 Threaded Mechanical Branch Tees Step 1 Step 2 1 Alignment Align the gasket and fitting above the 1.19" (30mm) pipe hole. BRANCH SIZE HOLE SAW SIZE EQUIVALENT PIPE LENGTH Inches (mm) Inches + 1 /8, -0 (mm +3, -0) (see note) Note: Flow Data is expressed as Feet/Meters of Schedule 40 steel outlet pipe with a "Hazen-Williams coefficient of friction value of 120". 2 HousingAssembly Attach the U-bolt from the otherside and fasten the nuts fingertight. Step 3 Specified Bolt Torque Specified bolt torque is forthe u-bolt used on SPF threaded mechanical branches. The nuts must be tightened alternately and evenly until fully tightened. Caution: Propertorquing of mechanical branch u-bolt is required to obtain specified performance. Over torquing the u-bolt may result in damage to the pipe and/or casting which could result in pipe joint separation. Undertorquing the u-bolt may result in lowerpressure retention capabilities, lowerbend load capabilities, joint leakage and pipe joint separation. Pipe joint separation may result in significant property damage and serious injury. 3Tighten Nuts Making sure the fitting is properly located overthe pipe hole, use a 9 /16" (14 mm) wrench to tighten the nuts alternatively to a recommended torque of ft.-lbs. (25-30 Nm) on pipe wall less than schedule 10 (DIN 2440) or23-27 ft.-lbs. (31-37 Nm) on pipe walls schedule 10 (DIN 2440) and above. FP-10.16

52 CAST IRON THREADED FITTINGS APPROVED Class 125 (Standard) FIG Elbow A A For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. Nominal Size FIGURE ELBOW Maximum Working Pressures Dimension A Approx. Wt. Each In. (mm) PSI (kpa) In. (mm) Lbs. (kg) s Working Pressure Ratings are for reference only and based on Sch. 40 pipe. For the latest UL/ULC, and FM pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. Dimensions: ASME B16.4 Class 125 Material: Finish: Threads: MATERIAL SPECIFICATIONS ASTM A126 Black or Hot Dip Galvanized per ASTM A153 Class A NPT per ASME B Agency Approvals: All cast iron threaded fittings are UL/ULC Listed and FM Approved. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: SPF/CI-1.15 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

53 CAST IRON THREADED FITTINGS APPROVED Class 125 (Standard) FIG Straight Tee A A A For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. Nominal Size FIGURE STRAIGHT TEE Maximum Working Pressures Dimension A Approx. Wt. Each In. (mm) PSI (kpa) In. (mm) Lbs. (kg) s Working Pressure Ratings are for reference only and based on Sch. 40 pipe. For the latest UL/ULC, and FM pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. Dimensions: ASME B16.4 Class 125 Material: Finish: Threads: MATERIAL SPECIFICATIONS ASTM A126 Black or Hot Dip Galvanized per ASTM A153 Class A NPT per ASME B Agency Approvals: All cast iron threaded fittings are UL/ULC Listed and FM Approved. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: SPF/CI-1.15 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

54 CAST IRON THREADED FITTINGS APPROVED Class 125 (Standard) FIG Reducing Coupling A For Listings/Approval Details and Limitations, visit our website at or contact an Anvil Sales Representative. FIGURE REDUCING COUPLING Nominal Size Maximum Working Pressures Dimension A Approx. Wt. Each In. (mm) PSI (kpa) In. (mm) Lbs. (kg) 1 x x x x s Working Pressure Ratings are for reference only and based on Sch. 40 pipe. For the latest UL/ULC, and FM pressure ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative. Dimensions: ASME B16.4 Class 125 Material: Finish: Threads: MATERIAL SPECIFICATIONS ASTM A126 Black or Hot Dip Galvanized per ASTM A153 Class A NPT per ASME B Agency Approvals: All cast iron threaded fittings are UL/ULC Listed and FM Approved. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: SPF/CI-1.15 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

55 300 RING HANGER APPROVED P.O. Box 3365 South El Monte, CA Fax www. Afcon.org NFPA 13 PIPE ROD 1 WT. 5 WT.+250 UL TEST LOAD 1 3/ /4 3/ /2 3/ / /2 3/ thru 4 inch pipe LISTED FOR STEEL/CPVC 1/2 & 3/4 inch pipe 5 thru 8 inch pipe /8 3/8 1/ / / SIZE - ROD- 3/8" or 1/2" SIZE - SYSTEM PIPE - 1/2" thru 8" MATERIAL- Carbon Steel. FINISH - Mil. Galvanized to G-90 specification. LISTING/APPROVAL- 203-EX "- 8" FM Approval guide - 1"- 8" OSHPD OPA-0601See Website. Conforms to Federal Specification WW-H-171E type 10, and Manufacturers Standardization Society SP-69, type 10. MAXIMUM TEMPERATURE F. FUNCTION - Pipe component ofan AFCONhanger. To support horizontal steel, CPVC or copper pipe. INSTALLATION - Per these instructions including NFPA13 and the CPVC manufacturers instructions. FEATURES * Sized and listed exclusively for use with #310 Surge Restrainer. * Band edge is offset for EASY pipe insertion. * Custom fit swivel nut for better retention in ring. ORDERING - Part #, pipe size. A B PIPE 1 1 1/4 1 1/ /2 3 4 A B /15 CAD

56 100 REVERSIBLE BEAM CLAMP 3/4" MOUTH APPROVED P.O. Box 3365 South El Monte, CA Fax www. Afcon.org SIZE - ROD: 3/8" SIZE - SYSTEM PIPE: 4" max. SIZE - ROD: 1/2" SIZE - SYSTEM PIPE: 8" max. MATERIAL - Ductile iron. FINISH - Plain, E.G. and H.D.G. LISTING/APPROVAL- FM 203-EX2551 FMApproved FUNCTION -Attachment component ofan AFCONhanger. To support horizontal piping. INSTALLATION - Per NFPA13 and these instructions. Install on steel flange - thickness less than 3/4". Set bolt up or down. ASSEMBLY/ATTACHMENT - See drawing. Torque - 3/8"= 60 lb-in or 1/2"= 125 lb-in. In the absence ofa torque wrench, engage set bolt finger tight then additionally tighten 1/4 turn. Only tighten set bolt with hand tools. NEVER INSTALLSET BOLT WITH IMPACT/DRILLDRIVER. FEATURES * Maintains CONSTANT HANGER CENTER-LINE, withset bolt up or down. * Flat throat back to prevent twisting on structure during installation. ORDERING - Part #, rod size and finish. 1/15 CAD CAD

57 SIDEWINDER FOR STEEL - Horizontal Application #14 SW Red Nut Driver Part # Application Approvals Rod Part Size Number Model Screw Descriptions Ultimate ULTest FM Test Min Max Box Pullout (lbs)load (lbs)load (lbs)thicknessthickness Qty HORIZONTALMOUNT 1/4" SWD 100 1/4-14 x 1" TEKS (16 ga.).060"-16 ga 3/16" /4" SWDR 100 * 1/4-20 x 1" TEKS (20 ga.).036"-20 ga 3/16" /8" SWD 10 1/4-14 x 1" TEKS (16 ga.).060"-16 ga 3/16" /8" SWD 10-SS 1/4-14 x 1" TEKS (16 ga.).060"-16 ga 3/16" /8" SWD 15 1/4-14 x 1-1/2" TEKS (16 ga.).060"-16 ga 3/ /8" SWD 20 1/4-14 x 2" TEKS (16 ga.).060"-16 ga 3/ /8" SWD 516 5/16-18 x 1-1/4" TEKS (20 ga.) ga 3/ /8" SWDR 1 * 1/4-20 x 1" TEKS (20 ga.) "-20 ga 3/16" /8" SWDR 1-1/2 * x 1-1/2" TEKS (3/16") "-3/16" 1/2" /8" SWDR 516 * 5/16-18 x 1-1/4" TEKS (20 ga.) "-20 ga 3/16" /8" SWT x 1-1/2" TEKS (3/16").188"-3/16" 1/2" *Includes retaining nut no pr e-dr ill ing r equir ed Product Features Made with Teks self-drilling fasteners - no pre-drilling required. Installs into steel range from 20 gauge 1/2 thicknesses. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have an RPM range of Saves time from traditional methods. Reduces installation costs. Quick to install using the Sammys Nut Driver with an 18Vcordless drill/driver. Made in the U.S.A. APPROVED Watch a video demonstration at Case Qty STEEL STEEL WOOD SAMMYS SWIVEL HEAD FOR STEEL - Swivel Application #14 Black Nut Driver Part # #14 SH Orange Nut Driver Part # Application Approvals Rod Part Size Number Model Screw Descriptions SWIVELMOUNT 3/8" SH-DSTR 1* 3/8" SH-TEK 50 1/4-20 X 1 TEKS x 1-3/4" TEKS x 1-3/4 1/ SH-TEK 5.0 TEKS 5 *Does not comply with ROHS requirements / Includes retaining nut 7 Product Features Eliminates distortion of threaded rod in sloped roof applications. Accommodates 3-1/2 x 12 pitch. Installs into angled z-purlin; allows threaded rod to hang plumb. Allows 17 deflection from vertical. Made in the U.S.A. Ultimate Pullout (lbs) ULTest Load (lbs) FM Test Min MaxBox Load (lbs)thickthickqty Case Qty 3220 (3/16 ) / (1/2" steel Vertical) 1306 (45 off Vertical) 2281 (3/16 HSS) 1585 (3/16 HSS 45 off Vertical) 2368 (1/2 steel Vertical) 1306 (45 off Vertical) 2281 (3/16 HSS) 1585 (3/16 HSS 45 off Vertical) 1500 (Vertical) 850 (45 off Vertical) 4" 2-1/2 Watch a video demonstration at 3/16" 1/2" /16" 1/2" To find a distributor near you, call 800-BUILDEX APPROVALS ACCESSORIES CONCRETE

58 THE SPECIFICATION OF THREADED ROD RIGHT HAND UNC COARSE THREAD DIAMETER 1/4-20 NOMINAL D (Major Diameter) FINISH SIZE Max. Min BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS 5/ /8-16 7/ /2-13 5/8-11 3/4-10 7/ / / / BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS BRIGHT / ZINC / HOT DIPPED GALV / STAINLESS SPECIFICATION REQUIREMENTS Dimensions: See major and length requirementabove Material & Mechanical Properties: Meets the minimum mechanical requirements of ASTM A 307 Grade A (minimum tensile of 60 kpsi) or ASTM F1554, Grade 36 (minimum tensile of 58 kpsi) Thread Requirements: Roll thread to ANSI B1.1 UNC Class 1A Coating: Zinc Plated Fe/Zn 3A per ASTM F1941 (CR6+) HDG Per ASTM A153 or F2329 Stainless AISI 304