Technical Sheet on Sprint Tachometers and MSD Ignition Systems. How to Install a Sprint Tachometer With a MSD 6A Ignition System
|
|
- Frederick Green
- 6 years ago
- Views:
Transcription
1 Technical Sheet on Sprint Tachometers and MSD Ignition Systems How to Install a Sprint Tachometer With a MSD 6A Ignition System
2 Step 1: Wiring Procedures Sprint Tachometers are voltage-triggered tachometers rather than being current-triggered tachometers such as stock units. IMPORTANT: DO NOT INSTALL BEFORE READING INSTRUCTIONS CAREFULLY. Your Sprint Tachometer has been carefully assembled, calibrated and tested before being packaged and shipped to you. Our instructions are carefully documented and are the result of our experience with thousands of installations of Sprint Tachometers. We hope you will follow these instructions carefully and explicitly to achieve the best results with this quality product. 1) Locate the Tachometer Filter packed with the tachometer. This Filter will be a round 5/8 x 1 in length and constructed of black plastic. Three color-coded wires (brown, purple and white) will be projecting from one end. 2) Connect the brown wire of the Filter to the brown wire of the Tachometer. 3) Connect the purple wire of the Filter to a metal bolt on the Engine Block. DO NOT connect this wire to either the GND wire of the tach or to any other common-ground connection behind the dash. 4) Connect the black wire from the Tachometer to a good ground point on the dash panel. 5) Connect the red wire from the Tachometer to the Scotch-Lok splice and then tap into the red with green stripe wire of your engine harness (from the rear of the ignition switch). Connecting to MSD Ignition Systems: The procedures outlined below will usually be the proper method for connecting the Sprint Tach to the most common MSD system the MSD-6A having a Blaster-2 Coil.
3 With the brown and purple filter wires already connected exactly as described in the paragraphs above, start the vehicle and let the engine idle. With someone in the car to watch the tachometer dial and to increase the engine speed, touch the end of the white wire of the Tach Filter to the minus (-) side of the MSD Blaster-2 Coil. The tachometer should now show a reading approximating the engine speed in RPMs (revolutions per minute). If the tachometer reading is correct at idle, gradually increase engine speed from idle to 3,000 to 4,000 revolutions. The tach reading should increase accordingly. If the tach reading does not increase or drops to a zero reading, do the following: Remove the white wire from the coil connection you first assumed was the minus (-) side (and normally the distributor side) and touch the end of the white wire to the other (small) terminal of the Coil. If no reading at all shows on the tach or engine speed begins to falter or drop off, go to the next paragraph. Remove the white wire from the Coil connection and with the engine still idling, touch the same white wire to the Tach Outlet connection terminal located on the side or end of the MSD 6-A box. You will probably now see a reading on the tachometer at idle. Increase the engine speed while monitoring the tach reading. If the reading tracks properly up to 2,500 or higher, but then drops off as engine speed is increased further, continue on with the steps outlined below. Disconnect the white wire from the MSD 6-A box. Disconnect the brown wire of the Tach Filter from the brown wire of the Sprint tachometer.
4 With the engine again at idle, touch the end of the brown wire of the Sprint Tach directly to the Tach Outlet terminal on the MSD 6-A box. A correct RPM reading at idle should now register on the tachometer. Caution: Do Not by-pass the Tach Filter UNLESS all of the above steps have been followed precisely. Gradually increase the engine speed to higher RPMs while watching the tach reading. If the tach pointer tracks correctly over the full engine RPM range, shut the engine off. You may now permanently connect the brown wire of the Sprint Tachometer to the Tach Outlet terminal on the MSD box. Next, disconnect the purple wire of the Tach Filter from the engine-block mounting point and remove the Tach Filter from the vehicle since it will no longer be able to be used in your installation. Should your Sprint Tachometer not respond properly after all the above steps and procedures are followed, your MSD system may require a special Tach Adapter 8910 or This unit is available through your MSD Division of Autotronics Controls dealer and instructions for installing the Adapters should be included with the part. This item is NOT manufactured by nor is it available through Dearborn Classics. It is our experience that only a very small number (estimated less than 2%) of vehicle owners and builders with our Sprint tachometer and a MSD Ignition system such as the MSD 6-A will ever require the MSD 8910 or 8920 Tach Adapter to be purchased and installed.
5
Mustang. Installation Manual. Revision 11/16/10
1967-1968 Mustang Installation Manual Revision 11/16/10 I Table of Contents TABLE OF CONTENTS...II WELCOME TO THE TEAM OF CLASSIC INSTRUMENTS!... III REMOVE ORIGINAL INSTRUMENT PANEL...1 DETERMINE SPEEDOMETER
More informationClassic Instruments. Ultimate Speedometer & Speed-Tachular. Installation Manual
Classic Instruments Ultimate Speedometer & Speed-Tachular Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Gauge Wiring... 4 Ultimate Speedometer Wiring Diagram...
More informationMustang. Installation Manual
1967-1968 Mustang Installation Manual Table of Contents WELCOME FROM THE TEAM AT CLASSIC INSTRUMENTS!... 3 REMOVE THE ORIGINAL INSTRUMENT PANEL... 4 WIRING DIAGRAM... 6 WIRING THE NEW INSTRUMENT CLUSTER...
More informationChevy Truck
Classic Instruments 1967 1972 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Remove the Stock / OEM Instrument Panel... 4 Instrument Cluster Wiring...
More informationMustang. Installation Manual
1967-1968 Mustang Installation Manual I Table of Contents TABLE OF CONTENTS... II WELCOME TO THE TEAM OF CLASSIC INSTRUMENTS!... III REMOVE ORIGINAL INSTRUMENT PANEL... 1 DETERMINE SPEEDOMETER SIGNAL...
More informationClassic Instruments Cluster. Installation Manual
Classic Instruments 6400 Cluster Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5 Speedometer & Tachometer
More informationClassic Instruments Ford F100. Installation Manual
Classic Instruments 1953 1955 Ford F100 Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5 Speedometer
More informationClassic Instruments Chevelle. Installation Manual
Classic Instruments 1964 1965 Chevelle Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Included Mounting Hardware... 4 Mounting Gauges... 5 Wiring Diagram... 6
More informationClassic Instruments Camaro. Installation Manual. Revised: January 6, 2015 Page 1
Classic Instruments 1967 1968 Camaro Installation Manual Revised: January 6, 2015 Page 1 Contents Welcome from the Team at Classic Instruments!... 3 Remove Original Instrument Panel... 4 New Instrument
More informationFord Mustang. Installation Manual
1965 1966 Ford Mustang Installation Manual TABLE OF CONTENTS Welcome from the Team at Classic Instruments! 3 Mounting Gauges in New Bezel 4 3 3/8 Speedometer Wiring 6 3 3/8 Speedometer Wiring Diagram 6
More informationINSTALLATION INSTRUCTIONS for. FC 2000 Series
INSTALLATION INSTRUCTIONS for Fire Control (FC) Ignition System FC 2000 Series Owners Manual Introduction...2 Specifications...2 Coil Compatibilities...2 Wire Functions...2 Connections...3-6 Connections
More informationClassic Instruments Ford. Installation Manual
Classic Instruments 1940 Ford Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5 Pulse Signal Generator
More informationClassic Instruments Chevy. Installation Manual
Classic Instruments 1957 Chevy Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting Gauges... 4 Speedo, Tach, Volt and Oil Pressure Gauge Wiring... 5 Speedo,
More informationTach-Force Chevy Truck
Classic Instruments Tach-Force 1955 1959 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5
More informationClassic Instruments Corvette. Installation Manual
Classic Instruments 1963 1967 Corvette Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting the Gauges... 4 Gauge Cluster Wiring... 6 Gauge Cluster Wiring Diagram...
More informationMSD Blaster Ignition PN 5900
MSD Blaster Ignition PN 5900 Note: Read these instructions completely before attempting any installation. Parts Included: 1 - Blaster Ignition, PN 5900 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground
More informationFord Mustang
Classic Instruments 1965 1966 Ford Mustang Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting the Gauges... 4 3 3/8 Speedometer Wiring... 6 3 3/8 Speedometer
More informationOPERATING INSTRUCTIONS
2 7 5 OPERATING INSTRUCTIONS PORTABLE PART NO. 28357 By functioning as a triggering device, Mallory's Portable Ignition Tester allows you to check the operation of a car s ignition system without starting
More informationChevy Truck
Classic Instruments 1973 1987 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Gauge Mounting... 4 Gauge Cluster Wiring... 6 Pulse Signal Generator [SN16]
More informationChevy Truck
Classic Instruments 1954 1955 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting Gauges... 4 4 5/8 Speedometer Wiring [no included tachometer]...
More informationReplacement Tach Board Manual
Replacement Tach Board Manual 67-74 Dodge and Plymouth Cars that use electronics Internal to the tachometer. Real Time Engineering 19352 Hilton Rd. Springdale, AR 72764 (479) 756-3917 fax Rev8 www.rt-eng.com
More informationClassic Instruments. Six Pack. Installation Manual
Classic Instruments Six Pack Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Universal, Shoebox & 61-66 F100 Gauge Mounting... 4 Bronc Package Gauge Mounting...
More informationClassic Instruments & 1956 Chevy. Installation Manual
Classic Instruments 1955 & 1956 Chevy Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Disassemble Original Gauge... 4 Assemble New Gauge Cluster... 5 Speedo, Tach,
More informationINSTALLATION MANUAL DIS4-009 DISTRIBUTORLESS IGNITION SYSTEM FOR ALL A/C VWs USING BOSCH 009 DISTRIBUTOR
INSTALLATION MANUAL DIS4-009 DISTRIBUTORLESS IGNITION SYSTEM FOR ALL A/C VWs USING BOSCH 009 DISTRIBUTOR TABLE OF CONTENTS INTRODUCTION... 2 GENERAL COMMENTS... 3 REMOVE STOCK COMPONENTS... 3 FIGURES...
More informationChevy Truck
Classic Instruments 1947 1953 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting Gauges... 4 4 5/8 Speedometer Wiring [no included tachometer]...
More informationMSD 7AL-3, Ignition Control PN 7230
MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,
More informationChevy Truck
Classic Instruments 1947 1953 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting Gauges... 4 4 5/8 Speedometer Wiring [no included tachometer]...
More informationClassic Instruments Corvette. Installation Manual
Classic Instruments 1963 1967 Corvette Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting the Gauges... 4 Gauge Cluster Wiring... 6 Gauge Cluster Wiring Diagram...
More informationMSD Zero-Cross Distributor Chevrolet - PN 83971
MSD Zero-Cross Distributor Chevrolet - PN 83971 Parts Included: 1 Distributor 1 Gasket 1 Hold Down & Hardware 1 Gear Lubricant 2 O-Rings IMPORTANT The Separate Pickup Zero-Cross Distributors use two completely
More informationClassic Instruments Chevy. Installation Manual
Classic Instruments 1951 1952 Chevy Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Included Mounting Hardware... 4 Mounting Gauges... 5 4 5/8 Speedometer Wiring
More informationINSTRUCTIONS. 20 Circuit Wiring Kit Instructions October 2009, Speedway Motors, Inc.
1 MAIN FUSE PANEL The main fuse panel harness s designed to be mounted under the dash a the firewall in an area close to the steering column. The enclosed representation of the main dash harness shows
More informationChevy Truck
Classic Instruments 1964 1966 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Gauge Mounting... 4 Gauge Cluster Wiring... 5 4 Wire Harness... 5 16 Wire
More informationChevrolet. Installation Manual
1959 1960 Chevrolet Installation Manual TABLE OF CONTENTS Welcome from the Team at Classic Instruments!... 3 Mount Adapter Ring... 4 Mount New 4-5/8 Gauge in Center Gauge Pod... 4 Mount New 2-1/8 Gauges
More informationWater Temperature. GM LS Engine Gauges Installation Guide
2650-1563-00 GM LS Engine Gauges Installation Guide Water Temperature For water temperature, there is a port located on the right side (passenger side) of the engine, in the cylinder head, past the last
More informationMSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor
More informationDYNOTUNE 2 STAGE RPM WINDOW SWITCH WITH TPS INSTALLATION INSTRUCTIONS
DYNOTUNE 2 STAGE RPM WINDOW SWITCH WITH TPS INSTALLATION INSTRUCTIONS Introduction: READ ALL INSTRUCTIONS BEFORE STARTING! This DynoTune device will control up to two stages of nitrous oxide. They are
More informationClassic Instruments. Installation Manual
Classic Instruments Installation Manual TABLE OF CONTENTS Welcome from the Team at Classic Instruments! 3 Mounting Gauges 4 4 Speedometer Wiring 5 4 Speedometer Wiring Diagram 5 16 Pulse Signal Generator
More informationMallory HyFire Electronic Ignition Control
Mallory HyFire Electronic Ignition Control PN 690 Parts Included: 1 - Ignition 1 - Harness, Mag Pickup 1-18" Ground Wire 1-100V/1A Diode 4 - Mounting Screws WARNING: During installation, disconnect the
More informationION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO
ION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO MOUNTING: It should be inserted into the opening from the front and the L-clamps will be installed from the back. Tighten the nuts on the L-clamps so that
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for WEGO II Wide-Band Exhaust Gas Oxygen Sensor Interface Methanol Version CAUTION: CAREFULLY READ INSTRUCTIONS
More informationMSD Pro-Billet Distributor Buick 400, 430, PN 8552 Buick Nailhead - PN 8524
MSD Pro-Billet Distributor Buick 400, 430, 455 - PN 8552 Buick Nailhead - PN 8524 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor,
More informationMSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595
MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark
More informationTachMatch Instructions
TachMatch Instructions Thank you for your purchase of the TachMatch Model TM01 from TechnoVersions LLC. The TachMatch has been designed to: accept various tachometer input signals (e.g., coil, MSD, HEI),
More informationMSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393
MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly
More informationPIMP Ford 5.0 Harness Installation Manual. Part Number: PM-75
PIMP Ford 5.0 Harness Installation Manual Part Number: PM-75 Ron Francis Wiring 200 Keystone Rd Suite 1 Chester, PA 19013 800-292-1940 www.ronfrancis.com Pre-Installation Notes: This system is designed
More informationMSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi
MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there
More informationHLY-3015 MINI SPEED/TACH INFORMATION SYSTEM (weather and vibration resistant for exposed environments)
HLY-3015 MINI SPEED/TACH INFORMATION SYSTEM (weather and vibration resistant for exposed environments) Neutral Left turn Low voltage Right turn High beam Engine Low oil *To avoid damage to motorcycle,
More informationInstallation Instructions for Lingenfelter Shift Light Controller with green LED
Installation Instructions for Lingenfelter Shift Light Controller with green LED PN: L460080000 1557 Winchester Road Decatur, Indiana 46733 260 724 2552 phone 260 724 8761 fax www.lingenfelter.com Parts
More informationSCHNITZ MOTORSPORTS USER MANUAL AND INSTALLATION GUIDE PRO-MOD BATTERY VOLTS DIAGNOSTICS NOS PULSE FREQUENCY NOS DELAY TIME IN SECONDS
SCHNITZ MOTORSPORTS DSC-CS "PRO-MOD" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, COIL, NEGATIVE GA WHITE, GA BLACK, SHIFT LIGHT +V OUTPUT PAGE 0 NOS ACTIVATION INPUT
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 8365
MSD Pro-Billet Chevrolet HEI Distributor PN 8365 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering
More informationTELORVEK III. WIRING INSTRUCTIONS FOR LT-40 LT-1 Fuel Injection System
TELORVEK III WIRING INSTRUCTIONS FOR LT-40 LT-1 Fuel Injection System Page #1 Thank you for purchasing the absolute finest of wiring kits for the General Motors fuel injection. We have taken considerable
More informationArctic Cat M-8 Install, 2015 Phantom and 2016 Phantom
PHANTOM TETH-AIR TM 2012-16 Arctic Cat M-8 Install, 2015 Phantom and 2016 Phantom As Arctic Cat does not include a factory tether connector on most models, the Phantom universal install kit(standard kit)
More information1984 Jeep CJ7. IGNITION SYSTEM - SOLID STATE' 'Distributors & Ignition Systems MOTORCRAFT SOLID STATE IGNITION (SSI)
TESTING SECONDARY CIRCUIT CHECK CAUTION: When checking secondary voltage, do not remove spark plug wires from spark plugs No. 3 on 4-cylinder, No. 1 or 5 on 6-cylinder and No. 3 or 4 on V8 Engines. 1.
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationINSTALLATION INSTRUCTIONS MECHANICAL GAUGES
1062650-1966-77 MECHANICAL GAUGES QUESTIONS: If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s), please contact Hardin Marine
More informationCopyright Triple S Customs
CADILLAC CONCOURS 1994-1997 VEHICLE WIRING Copyright 2002-2004 Triple S Customs WIRING INFORMATION: 1994 Cadillac Concours 12V CONSTANT WIRE RED Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION
More informationMSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302
MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your
More informationOptional: Wiring a Relay for Gauge Controlled Output
Wiring Installation Instructions for : PYROMETER 2 1/16 Spek Pro Professional Racing Gauge GAUGE 12-Pin Wiring Harness & Plug Firewall Grommet DIAGRAM 1 Black-Engine Ground 12-Pin Wiring Harness CUP Coil
More informationBULLET & MINI-BULLET TACHOMETERS INSTALLATION GUIDE - Please see appropriate section for your specific application
Revision: 17.7-04/12/2012 Install Time: 30 to 90 Minutes BA-757x-xx Page: 1 Go slowly and follow instructions carefully. The installation is very easy if the wire color destinations are followed. INCLUDED
More informationUSER MANUAL AND INSTALLATION GUIDE ENGINE RPM AND NOS SHIFT COUNTER NOS DELAY TIME IN SECONDS NOS START PERCENT NOS FINAL PERCENT
SCHNITZ MOTORSPORTS DSC-9PS "PRO-STREET" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE SHIFT LIGHT POSITIVE PAGE 2 SHIFT LIGHT GROUND PAGE 2 NOS SOLENOID GROUND 1GA ORANGE, FUEL SOLENOID GROUND
More informationClassic Update Series
*** These are special instructions for connecting your wiring system to a stock instrument cluster. *** NOT: If you are using after market gauges, follow the instructions included in the 92965220 Gauge
More informationInstallation Manual for VMAC Throttle Commander Throttle Control T500111
Installation Manual for VMAC Throttle Commander Throttle Control T500111 2006-2007 Classic GMC CK2500-3500 6.0L Gasoline Engines 1.0 Preparation for Installation...4 1.1 Automatic Transmission Trucks...4
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor 1 - Rotor,
More informationThank you for your purchase Off-ROad NOtice: PROduct WaRNiNgs:
Thank you for your purchase. Please, read the instructions and watch the video before installing the JMS Progressive N20 Controller. Configuration and installation videos are available online: www.jms-nos.com.
More informationGM EST Distributor Kit
GM EST Distributor Kit Electronic Spark Timing (EST) For Inboards & Stern drive applications Instructions Part Number: BPIESTGMV8 It is recommended that you read this instruction manual to become familiar
More informationMSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425
INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm
More informationMSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020
INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition
More informationMSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573
MSD Pro-Billet Ready-to-Run Ford Flathead, 1949-1953 PN 8573 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your
More informationOverview of EIS Installation
Overview of EIS Installation Thank you for purchasing an Electroair Ignition System for your aircraft. We are confident that you will be happy with the performance of your EIS on your aircraft. The next
More informationReplace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting
INSTALLATION INSTRUCTIONS SHORT SWEEP ELECTRIC GAUGES 2650-1079-00 Rev. C CAUTION FOR ALL GAUGE INSTALLATION (AMMETERS EXCLUDED) As a safety precaution, the +12V wire attached to the positive I (+) terminal
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653
MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with
More informationFEATURES: SPEK PERFORMANCE GAUGE TACHOMETER FEATURES:
Wiring Installation Instructions for : RPM Tachometer PACKAGE CONTAINS: Tachometer Gauge 2 1/16 INCH Wiring Harness Mounting Cup (Not required for pod installation) (2) Neoprene EDPM Grommets SPEK MONITOR
More informationMSD Digital-7 Plus Ignition Control PN 7520
INSTALLATION INSTRUCTIONS MSD Digital-7 Plus Ignition Control PN 7520 Parts Included: 1 - MSD Ignition 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground Wire 1 - White Jumper 1 - Red Jumper 2 - Violet
More informationMODEL HLY-2001 rev. B TANK MOUNT SPEEDOMETER/TACHOMETER INFORMATION SYSTEM
MODEL HLY-2001 rev. B TANK MOUNT SPEEDOMETER/TACHOMETER INFORMATION SYSTEM Please read this before beginning installation or wiring. POWER Connect the red wire from the main harness to accessory power
More informationCONTROL BOX. Wiring the control box into the vehicle. +12V
CONTROL BOX Once the display panel is in place, mount the control box within the connecting cable's distance (approximately 3 feet) and secure to the underside of the dashboard. This case does not have
More informationClassic Instruments. Installation Manual. Revised: July 23,
Classic Instruments Installation Manual Revised: July 23, 2018 1 Table of Contents Speedometer Installation... 4 Speedometer Wiring... 4 16-Pulse GM / Chrysler Signal Generator [SN16]... 5 Ford Signal
More informationBSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines
BSR BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines Features Digital Advance The main feature of the Magic Box is the digital advance that replaces conventional weights and springs.
More informationMSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440
MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our
More informationUSER MANUAL AND INSTALLATION GUIDE TIMER DELAY IN SECONDS SHIFT STYLE & SHIFT COUNTER TIMER DURATION NOS DELAY TIME IN SECONDS NOS START PERCENT
SCHNITZ MOTORSPORTS DSC-TG0- "TOP-GAS " IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, PAGE COIL, NEGATIVE GA WHITE, PAGE SHIFT LIGHT GROUND 0GA BROWN, PAGE 0 SHIFT
More informationTri-Spark Ignition System Installation Triple Cylinder TRI-0001
Tri-Spark Ignition System Installation Triple Cylinder TRI-0001 There are potentially lethal high voltages produced at the ignition coils and spark plugs, therefore every precaution must be taken to prevent
More informationSPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL
SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationMSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253
INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will
More informationP/N 646 MODE L LOW RPM H HIGH RPM C CYLINDER SELECT P/N 646 H HIGH RPM C CYLINDER SELECT WINDOW RPM SWITCH L LOW RPM VALUE MODE MODE DOWN RED GREEN
INSTALLATION INSTRUCTIONS FORM 1008 (REV A) 01/02 WINDOW RPM ACTIVATED SWITCH PART NO 646 Parts Included in this kit: 1 RPM Activated Switch Part No 646 1 U shaped crimp-on wire terminal 1 #6 x 1/4" sheet
More informationMSD Digital 6 Plus Ignition Control PN 6520
INSTALLATION INSTRUCTIONS 1 MSD Digital 6 Plus Ignition Control PN 6520 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug
More informationCalibration Procedures:
Calibration Procedures: Setting the Ignition Timing Correction Selecting an Advance Curve Setting Rev Limit RPM These Instructions are for Tempest II Ignitions Only Rev. C // Severe engine damage is possible
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 275+ & 300+ STREET / STRIP DIGITAL MULTI-STRIKE CD IGNITION CONTROLLER GENERAL INFORMATION The features of the 275+ and 300+ Ignitions are the same, with one exception: the 300+
More informationRevised November 16, Classic Instruments. Installation Manual
Classic Instruments Installation Manual I TABLE OF CONTENTS Speedometer Installation 1 Speedometer Wiring 1 16-Pulse GM / Chrysler Signal Generator [SN16] 2 Ford Signal Generator Adapter [SN17] 2 3 ⅜ Speedometer
More informationThe gauges selected for my installation were the following: Part Application
This write up documents the installation of Autometer Sport Comp II gauges into a 1971 Camaro with original full factory instrumentation. The Autometer gauges completely replace the original factory instrumentation,
More informationFull Sweep Minor Gauge Wiring:
Full Sweep Minor Gauge Wiring: Notes on Senders: Temp Hi match/vdo 150C: Normally used in Oil temp, 140 280F. Temp Low match/vdo120c: Normally used in water temp, 100 240F. To test the gauges work (oil,
More informationMSD SCI Series PN 6300 & PN 6320
MSD SCI Series PN 6300 & PN 6320 IMPORTANT: Read these instructions before attempting this installation! Parts Included: 1 - MSD SCI Series Ignition 1 - Harness, PN 8860 1 - Parts Bag, ASY 10506, SCI Only
More informationCommander IS0128 ISO128E ECR# /04. Tachometer/ Engine Hourmeter
Commander Tachometer/ Engine Hourmeter Analog Tachometer Digitally displays Hours Engine Has Been Run Fuel Level Other Features if Available: Fuel anagement Fuel Flow in GPH or LPH Total or Trip Fuel Used
More informationTELORVEK II RJ-32 Big Block RamJet Fuel Injection System
Page #1 TELORVEK II RJ-32 Big Block RamJet Fuel Injection System This wiring system is compatible with the GM Performance part big block Ramjet 502 engine. The harness is designed to dress up the appearance
More informationMSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219
INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect
More informationACCEL SUPER BOX P/N 61212
FRM 34395 INSTALLATION INSTRUCTIONS ACCEL SUPER BOX P/N 61212 PARTS INCLUDED: (x1) Ignition (x1) 18 Ground Wire (x4) Mounting Screws (x1) Harness (x1) 100V/1A Diode WARNING! During installation, disconnect
More informationUNIVERSAL GAUGE WIRE HARNESS
2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness
More informationAURORA SERIES GAUGES FUEL GAUGE SUGGESTED TOOLS AND MATERIALS. 3 3 /8 in (85.7 mm) PARTS LIST
GAUGE INSTALLATION. Select mounting locations for the fuel gauge. 2. Cut a 2 /6 (52 mm) diameter hole for the gauge and test for proper fitmate. 3. Tighten the gauge with the enclosed Aurora Mounting Clamp
More informationGDP LB7 Duramax Digital Switch Installation. Step 1 Disconnect batteries.
page 1 This instruction manual covers installation of the gauge pod mount DSP/SOTF switch for 2001-2004 LB7 classic/gmt-800 trucks only. DISCLAIMER: Tuning, LLC will not be held responsible for any personal,
More informationStreet Fire CDI PN 5520
Street Fire CDI ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue
More information