ACE Turbine instruction manual

Transcription

1 ACE Turbine instruction manual Limited warranty Turbojet engine running life,depend operating environment, operating methods have a direct relationship, turbojet engine used the most compact structure to achieve the most extreme working conditions, design and production of each parts are extreme, is extremely harsh working conditions. Don t disassembly by youself, turbojet engine once apart, must be installed in accordance with the specification to precision to achieve the original performance, random assembly will overbalance the vortex spray ontology, under high-speed operation may cause serious consequences. ACE turbine engine new buyers enjoy natural damage or use of 25 hours one year warranty, if encounter questions or operation problems in use, please contact the sales hobby shop. Part 1 safety ACE Turbine engine used only limit on RC model, the working state of the turbojet engine essence for highly extreme mechanical work, there is a certain risk, the operator must be familiar with the operation before use points with known risks, inadvertent operation cause vortex spray body damage and injuries, please carefully read the instructions manual, strictly comply with the requirements of the operation. If this is your first turbojet engine operation, please in operating experience person operating under the guidance of learning. Before you start the turbojet engine for the first time, please read this manual carefully. (1) Safety operation distance Turbojet engine working under high rotation speed, the engine running, be sure to keep a safe distance, turbojet engine front three meters distance, left and right side keep five meters distance, rear ten meters distance

2 (2) fire extinguisher Must use CO2 fire extinguisher. If use dry chemical fire extinguisher, dry powder sprayed into the engine, can cause bearing serious damage. (3) Using turbo jet lubricating oil Using kerosene or diesel fuel spray against the 5% of lubricating oil, it is recommended to use mobil jet oil II. Part 2 setup

3 Part 3.Auto restart ECU This ECU is designed for high performance micro turbojet engine, the design of the automatic fuel a startup controller, using 32-bit high speed chip, has frame out automatically restart function, multiple protection, color screen, software can upgrade, the speed control precision, throttle response rapidly, and many other advantages Connect:

4 Power cable and sensor cable Battery/pump cableand throttle cable Power Cable Throttle Cable Batt & Pump cable Sensor Cable Rpm Display(option) GSU Receiver voltage:5-8.4v(5s Nimh or 2S Life or 2S Lipo) Power voltage: v (3S Life or 3S Lipo) Operation menu:

5 Boot screen: 1.Speed, temperature, current consumption, accumulative total electricity, power voltage, receiver voltage, engine condition and so on 2.ACC:from idle to the max rpm acceleration time, in seconds 3.Pump output voltage x100,ex,4.3v display Can switch Celsius or Fahrenheit temperature unit, and a correction function Large font screen 1.at boot screen,press Cancel,into large font screen Main menu: 1. Under the boot screen, press OK key, into main menu, click Cancel to exit into the boot screen 2. Languang switchable 3. If you need to display all the menu functions (hidden),press display all menu

6 Start up: This menu for startup parameter control 1. Fuel pump voltage for ignition fuel pump when the driving voltage, if every time the ignition fuel pump can't turn smoothly or ignition timing process, increase the value 2. glow plug voltage 6.0 V, this is a fixed value does not need to change, increase voltage raise the risk of damage. Learn RC: 1. This menu to set the throttle travel, Futaba remote control throttle channel must be set to reverse 2.max:throttle up,trim up 3.idle:throttle down,trim up 4.min:throttle down,trim down 5.lost safe time:1.0 sec

7 Cooling: 1. Set the cooling rpm after shut down,when manual shut down automatically to cooling down to 80 degrees Celsius. When flame out, because the ECU can't determine whether accident flame out with fire, does not automatically for cooling.in this case need by manual cooling. 2. Startup if the temperature is higher than 60 degrees, will be first for cooling, until the temperature dropped to 60 degrees, will begin to start Engine running: This menu control running parameters 1. Max rpm:max rpm limit 2.Idle rpm:rpm for idle 3.min rpm:set the minimum rpm, below this rpm automatically shut down 4.Max temp:starting or in running, will automatically reduce fuel supply, if the continuous high temperature, automatically shut down 5.Low volt:low volt warning 6.Restart:Can be set effective or ineffective, flame out automatically restart or not 7.Restart power pump:control of fuel supply when restart, if restart failed during the test, is to adjust the value,normaly range between 0.5V-1.1V

8 RPM acceleration delay: 1. Setup the acceleration rate 2. When change FULL (high speed), the ECU will automatically calculate the response of IDLE the acceleration rate of value (low speed), if because of hot weather, high altitude, turbine flame out when acceleration, must reduce the acceleration (Full) rate in order to run steady 3. If need to reduce the acceleration rate, the (FULL) value recommended range is between , the lower the value to accelerate will be slower.no need to change (IDLE) value it can be adjust automaticly. 4. IDLE:change low rpm acceleration Test function: This menu provides the test function of each parts When test pump, must press ok continue

9 Data chart Record running data Advanced menu: 1. Need to adjust the hidden function, to open all the menu Part 4 spec

10 Diameter:84mm Length:232mm Weight:820g RPM range:50, ,000 Thrust:6Kg Exhaust temperature:650 Celsius Fuel:kerosene or diesel Lubricating oil:5% Mobil jet oil II Maintance:25hr