Installation instructions for fuel dispensers OCEAN BMP4000.O EURO,

Transcription

1 INSTALLATION INSTRUCTIONS FOR FUEL DISPENSERS OCEAN BMP000.O EURO Attachment 1 Foundation schemes and frames Document: Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames File: IN02 EN_01_OceanFoundationSchemesRev03 Revision & Date: Revision 03, September 2013 Pages: 18 (including the cover) Created by: Ing. Milan Berka TATSUNO EUROPE a.s., Pražská 2325/68, Blansko, Czech Republic, tel , europe.com

2 TATSUNO EUROPE a.s. Pražská 2325/ Blansko Česká republika Tel: Fax: e mail: info@tatsuno europe.com, tatsuno europe.com Copyright This manual and its parts must not be copied without the consent of TATSUNO EUROPE a.s.

3 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames CONTENTS CONTENTS... 3 INTRODUCTION... ATTACHMENT 1. 1 FOUNDATION SCHEMES FOR THE SUCTION VERSIONS OF DISPENSERS... 5 ATTACHMENT SCHEME FOR THE DISPENSER BMP012.OE AND BMP012.OE... 5 ATTACHMENT SCHEME FOR THE DISPENSER BMP022.OE AND BMP02.OE... 6 ATTACHMENT SCHEME FOR THE DISPENSER BMP033.OE AND BMP036.OE... 7 ATTACHMENT SCHEME FOR THE DISPENSER BMP0.OE AND BMP08.OE... 8 ATTACHMENT SCHEME FOR THE DISPENSER BMP055.OE AND BMP0510.OE... 9 ATTACHMENT CONNECTION PIECE DRAWING (BELLOWS) ATTACHMENT 1. 2 FOUNDATION SCHEMES FOR REMOTE VERSIONS OF DISPENSERS ATTACHMENT SCHEME FOR THE DISPENSER BMP011.OE AND BMP012.OE ATTACHMENT SCHEME FOR THE DISPENSER BMP022.OE AND BMP02.OE ATTACHMENT SCHEME FOR THE DISPENSER BMP033.OE AND BMP036.OE ATTACHMENT SCHEME FOR THE DISPENSER BMP0.OE AND BMP08.OE... 1 ATTACHMENT SCHEME FOR THE DISPENSER BMP055.OE AND BMP0510.OE ATTACHMENT DETAIL OF THE INTAKE PIPING CONNECTION ATTACHMENT 1. 3 FOUNDATION SCHEMES OF SPECIAL VERSIONS ATTACHMENT SCHEME OF THE SATELLITE DISPENSER BMP001.OEL /SAT ATTACHMENT SCHEME FOR THE DISPENSER BMP021.OE/UH ZV1 REMOTE VERSION

4 TATSUNO EUROPE a.s., europe.com INTRODUCTION This attachment contains the foundation schemes for all variants of the OCEAN dispensers for both the suction version, when the dispenser has its own pump and meter, and the remote version, when the dispenser has only a filter and meter, but it is connected to a station tank with a central submersible pump. At the time of publication, the content of this attachment was accurate. The producer reserves the right to change the technical parameters of the appliance or its attributes without a written notice, since the technology is constantly improving and developing. All rights reserved. No part of the manual may be reproduced or transmitted without a written consent of the company TATSUNO EUROPE a.s. Document revisions Revision No / Date Changes Prepared by Revision 01 / Basic version of the document Ing. Milan Berka Revision 03 / For OCEAN dispensers with new hose retractors, versions CUBE, FIN and WAVE Ing. Milan Berka

5 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT 1. 1 FOUNDATION SCHEMES FOR THE SUCTION VERSIONS OF DISPENSERS ATTACHMENT SCHEME FOR THE DISPENSER BMP012.OE AND BMP012.OE The plan applies to suction models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP011.OEL BMP011.OER BMP011.OEL /VR BMP011.OER /VR BMP011.OEL /H BMP011.OER /H BMP012.OED BMP012.OED /H BMP012.OED /VR 1 Oval flange PN6 DN32 (G 1¼") according to ČSN EN Outlets of electric cables for power supply to the dispenser 2 Suction piping TR.5 x Outlet of electric cables for communication 3 Leak catcher tray 8 2x dowel for concrete Ø12 The fume exhaust piping TR 32 x 2.5 ends with an internal thread G1 (the dispensers for diesel oil are not equipped with it) 9 This surface must be on the same level as the base frame! 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 5

6 TATSUNO EUROPE a.s., europe.com ATTACHMENT SCHEME FOR THE DISPENSER BMP022.OE AND BMP02.OE The scheme applies to suction models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP022.OEL BMP022.OER BMP022.OEL /H BMP022.OER /H BMP022.OEL /H /VR BMP022.OER /H /VR BMP022.OEL /VR2 BMP022.OER /VR2 BMP02.OED BMP02.OED /H BMP02.OED /H /VR BMP02.OED /VR2 BMP021.OEL /UH BMP021.OER /UH BMP022.OED /UH /H BMP022.OEL /H /UH BMP022.OER /H /UH 1 Oval flange PN6 DN32 (G 1¼") according to ČSN EN Outlet of electric cables for communication 2 Suction piping TR.5 x x dowel for concrete Ø12 The fume exhaust piping TR 32 x 2.5 ends with an internal thread G1 (the dispensers for diesel oil are not equipped with it) 5 Anchoring holes 6 Outlets of electric cables for power supply to the dispenser Recommended direction of vehicle arrival to the fuel dispenser The order of fuel products 6

7 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT SCHEME FOR THE DISPENSER BMP033.OE AND BMP036.OE The scheme applies to suction models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP033.OEL BMP033.OER BMP033.OEL /H BMP033.OER /H BMP033.OEL /VR2 BMP033.OER /VR2 BMP033.OEL /H /VR BMP033.OER /H /VR BMP036.OED BMP036.OED /H BMP036.OED /VR2 BMP036.OED /H /VR 1 Oval flange PN6 DN32 (G 1¼") according to ČSN EN Outlet of electric cables for communication 2 Suction piping TR.5 x x dowel for concrete Ø12 The fume exhaust piping TR 32 x 2.5 ends with an internal thread G1 (the dispensers for diesel oil are not equipped with it) 5 Anchoring holes 6 Outlets of electric cables for power supply to the dispenser Recommended direction of vehicle arrival to the fuel dispenser The order of fuel products 7

8 TATSUNO EUROPE a.s., europe.com ATTACHMENT SCHEME FOR THE DISPENSER BMP0.OE AND BMP08.OE The scheme applies to suction models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP0.OEL BMP0.OER BMP0.OEL /H BMP0.OER /H BMP0.OEL /VR3 BMP0.OER /VR3 BMP0.OEL /H /VR2 BMP0.OER /H /VR2 BMP08.OED BMP08.OED /H BMP08.OED /VR3 BMP08.OED /H /VR2 1 Oval flange PN6 DN32 (G 1¼") according to ČSN EN Outlet of electric cables for communication 2 Suction piping TR.5 x x dowel for concrete Ø12 The fume exhaust piping TR 32 x 2.5 ends with an internal thread G1 (the dispensers for diesel oil are not equipped with it) 5 Anchoring holes 6 Outlets of electric cables for power supply to the dispenser Recommended direction of vehicle arrival to the fuel dispenser The order of fuel products 8

9 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT SCHEME FOR THE DISPENSER BMP055.OE AND BMP0510.OE The scheme applies to suction models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP055.OEL BMP055.OER BMP055.OEL /H BMP055.OER /H BMP055.OEL /VR BMP055.OER /VR BMP055.OEL /H /VR3 BMP055.OER /H /VR3 BMP0510.OED BMP0510.OED /H BMP0510.OED /VR BMP0510.OED /H /VR3 1 Oval flange PN6 DN32 (G 1¼") according to ČSN EN Outlet of electric cables for communication 2 Suction piping TR.5 x x dowel for concrete Ø12 The fume exhaust piping TR 32 x 2.5 ends with an internal thread G1 (the dispensers for diesel oil are not equipped with it) 5 Anchoring holes 6 Outlets of electric cables for power supply to the dispenser Recommended direction of vehicle arrival to the fuel dispenser The order of fuel products 9

10 TATSUNO EUROPE a.s., europe.com ATTACHMENT CONNECTION PIECE DRAWING (BELLOWS) Oval flange for connection to the fuel suction piping 3 Flange for connection to the pumping monoblock entry 2 Flexible piping bellows 10

11 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT 1. 2 FOUNDATION SCHEMES FOR REMOTE VERSIONS OF DISPENSERS ATTACHMENT SCHEME FOR THE DISPENSER BMP011.OE AND BMP012.OE The scheme applies to remote models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP011.OEL BMP011.OER BMP011.OEL /VR BMP011.OER /VR BMP011.OEL /H BMP011.OER /H BMP012.OED BMP012.OED /H BMP012.OED /VR 1 Intake piping with regulated height, ending with a ball valve with an adapter from G1 to G1 ½ (see details in section ) 7 Outlet of the electric cables for the data line 2 Axis of the intake pressure piping 8 2 x dowel for concrete Ø12 Fume exhaust piping ending with an internal thread G1" (the dispensers for diesel oil are not equipped with it) 10 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 6 Outlets of electric cables for power supply to the dispenser 11

12 TATSUNO EUROPE a.s., europe.com ATTACHMENT SCHEME FOR THE DISPENSER BMP022.OE AND BMP02.OE The scheme applies to remote models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP022.OEL BMP022.OER BMP022.OEL /H BMP022.OER /H BMP022.OEL /H /VR BMP022.OER /H /VR BMP022.OEL /VR2 BMP022.OER /VR2 BMP02.OED BMP02.OED /H BMP02.OED /H /VR BMP02.OED /VR2 BMP021.OEL /UH BMP021.OER /UH BMP022.OED /UH /H BMP022.OEL /H /UH BMP022.OER /H /UH 1 Intake piping with regulated height, ending with a ball valve with an adapter from G1 to G1 ½ (see details in Section ) 7 Outlet of the electric cables for the data line 2 Axis of the intake pressure piping 8 2 x dowel for concrete Ø12 Fume exhaust piping ending with an internal thread G1" (the dispensers for diesel oil are not equipped with it) 10 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 6 Outlets of electric cables for power supply to the dispenser The order of fuel products 12

13 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT SCHEME FOR THE DISPENSER BMP033.OE AND BMP036.OE The scheme applies to remote models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP033.OEL BMP033.OER BMP033.OEL /H BMP033.OER /H BMP033.OEL /VR2 BMP033.OER /VR2 BMP033.OEL /H /VR BMP033.OER /H /VR BMP036.OED BMP036.OED /H BMP036.OED /VR2 BMP036.OED /H /VR 1 Intake piping with regulated height, ending with a ball valve with an adapter from G1 to G1 ½ (see details in Section ) 7 Outlet of the electric cables for the data line 2 Axis of the intake pressure piping 8 2 x dowel for concrete Ø12 Fume exhaust piping ending with an internal thread G1" (the dispensers for diesel oil are not equipped with it) 10 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 6 Outlets of electric cables for power supply to the dispenser The order of fuel products 13

14 TATSUNO EUROPE a.s., europe.com ATTACHMENT SCHEME FOR THE DISPENSER BMP0.OE AND BMP08.OE The scheme applies to remote models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP0.OEL BMP0.OER BMP0.OEL /H BMP0.OER /H BMP0.OEL /VR3 BMP0.OER /VR3 BMP0.OEL /H /VR2 BMP0.OER /H /VR2 BMP08.OED BMP08.OED /H BMP08.OED /VR3 BMP08.OED /H /VR2 1 Intake piping with regulated height, ending with a ball valve with an adapter from G1 to G1 ½ (see details in Section ) 7 Outlet of the electric cables for the data line 2 Axis of the intake pressure piping 8 2 x dowel for concrete Ø12 Fume exhaust piping ending with an internal thread G1" (the dispensers for diesel oil are not equipped with it) 10 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 6 Outlets of electric cables for power supply to the dispenser The order of fuel products 1

15 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT SCHEME FOR THE DISPENSER BMP055.OE AND BMP0510.OE The scheme applies to remote models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP055.OEL BMP055.OER BMP055.OEL /H BMP055.OER /H BMP055.OEL /VR BMP055.OER /VR BMP055.OEL /H /VR3 BMP055.OER /H /VR3 BMP0510.OED BMP0510.OED /H BMP0510.OED /VR BMP0510.OED /H /VR3 1 Intake piping with regulated height, ending with a ball valve with an adapter from G1 to G1 ½ (see details in Section ) 7 Outlet of the electric cables for the data line 2 Axis of the intake pressure piping 8 2 x dowel for concrete Ø12 Fume exhaust piping ending with an internal thread G1" (the dispensers for diesel oil are not equipped with it) 10 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 6 Outlets of electric cables for power supply to the dispenser The order of fuel products 15

16 TATSUNO EUROPE a.s., europe.com ATTACHMENT DETAIL OF THE INTAKE PIPING CONNECTION 1 Intake filter 5 Ball stop valve 2 Flange 6 Adapter from G1 to G1 ½ 3 Cap nut with a sealing ring 7 Base frame Connecting pipe allowing height adjustment of the intake pipe in the range 25mm to 5mm 8 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 16

17 Installation instructions for fuel dispensers OCEAN BMP000.O EURO, Attachment 1 Foundation schemes and frames ATTACHMENT 1. 3 FOUNDATION SCHEMES OF SPECIAL VERSIONS ATTACHMENT SCHEME OF THE SATELLITE DISPENSER BMP001.OEL /SAT The scheme applies to the model: BMP001.OEL /SAT 1 Oval flange PN6 DN32 (G 1¼") according to ČSN EN Anchoring holes 2 Intake pressure piping TR.5 x Outlet of the electric cables for control of the satellite (min. 2m) 3 Leak catcher tray Recommended direction of vehicle arrival to the fuel dispenser 17

18 TATSUNO EUROPE a.s., europe.com ATTACHMENT SCHEME FOR THE DISPENSER BMP021.OE/UH ZV1 REMOTE VERSION The scheme applies to remote models of the dispensers OCEAN (WAVE/FIN/CUBE) and their variants: BMP011.OEL /UH ZV1 BMP011.OER /UH ZV1 BMP011.OED /UH ZV1 1 Intake piping with regulated height, ending with a ball valve with an adapter from G1 to G1 ½ (see details in section ) 7 Outlet of the electric cables for the data line 2 Axis of the intake pressure piping 8 2 x dowel for concrete Ø12 10 Emergency shut off valve OPW 10BF firmly fixed to the base (not part of the standard delivery of the dispenser) 5 Anchoring holes Recommended direction of vehicle arrival to the fuel dispenser 6 Outlets of electric cables for power supply to the dispenser The order of fuel products 18