Aerolite Wraparound Bulkhead: DOT Models
|
|
- Elmer Hodge
- 6 years ago
- Views:
Transcription
1 OWNER'S MANUAL Installation Instructions and Parts List READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION Aero Industries, Inc. Attention Dealers: Please give these instructions to the customer when the product is delivered. Indianapolis, IN Omaha, NE Streetsboro, OH R
2 Three kinds of special explanations will appear in these instructions. Be sure to read and follow them. WARNING: Possible danger to the operator or bystander. The operator or bystander could be injured if you ignore this information. CAUTION: Risk to the product. If you ignore this information the Product or the Vehicle could be damaged. NOTE: Contains additional information about a feature or step critical to the installation of this product. TOOLS REQUIRED FOR INSTALLATION Air or Electric Drill 9/16" Drill Bit 3/4" Open End or Box Wrench 3/4" Socket Air or Electric Impact Wrench Torque Wrench Hammer 24" Square Welder (If necessary to Install Stake Pockets) WARNING: This product meets D.O.T. standard # (d) (1) for its published load rating when installed in strict accordance with these instructions and the hardware specified. Any modifications to this product, substitutions of specified hardware or failure to follow these instructions, WILL void the load rating and may result in injury or death. TRAILER PREPARATION 1. Be sure that the bulkhead you are installing is the correct size and width to fit your flatbed application. 2. Make sure there is a flat, clean surface where the bulkhead bottom rail will meet the trailer top rail. Grind down any welds on the trailer top rail which will create an uneven surface. 3. A trailer stake pocket MUST BE available for the leg of the bulkhead to rest in. For a 10" wrap bulkhead, the center of the pocket must be 10-1/2" from the front of the trailer. For a 22" wrap bulkhead, the center of the pocket must be 22-1/2" from the front of the trailer. Failure to locate a pocket around the leg of the bulkhead WILL void the DOT rating. (See Step 1, Paragraph 3 on Page 3) Customer: If you have any concerns or questions prior to the installation of this product, please call our Customer Service at Aero Warranty Aero Products come with a one year warranty on all parts. It's another example of our on going commitment to customer satisfaction and quality. 1
3 STEP 1 - Installing the Bulkhead 1. Check your hardware package against the drawings shown to ensure the right size and quanity. All hardware should be Grade 8 and Zinc coated. Hardware Package P/N /2" Bolt HHCS (Qty. 4) 1/2" /2" Bolt HHCS (Qty. 2) 1/2"-13 Washer Flat (Qty. 6) 1/2" 1/2" 1/2"-13 Washer Lock (Qty. 12) Nut Hex (Qty. 6) WARNING: The legs of the bulkhead must be installed into a stake pocket. Failure to do so will void the DOT rating. NOTE: Stake pockets may be ordered from Aero Industries, Inc. if required. WARNING: Attempting to lift the bulkhead without a lifting device may cause personal injury to the installer. NOTE: Before drilling holes to mount the bulkhead across the front, be sure that there are no electrical or air lines underneath that will be damaged and that there is sufficient clearance on each side of the fifth wheel plate. Figure 1 1/2"-13 x 1-1/2" Bolt 1/2"Flat Washer 1/2"Lock Washer Aero Industries, Inc. 1/2"-13 Nut 12" Approximate 2
4 Aerolite Wraparound Bulkhead DOT Models 2. See Figure 1. Drill four 9/16" holes through the bottom plate of the bulkhead and the top wall of the trailer front rail using the recommended spacing. Bolt the bulkhead to the trailer using the 1-1/2" bolts, flat washers, lock washers, and hex nuts. NOTE: Do not tighten nuts completely at this time. 3. See Figure 2. If there was not a stake pocket on the trailer to accept the leg of the bulkhead, drive one between the bulkhead stake and the trailer rub rail until it is square with the top rail and positioned 1/4" below the top surface. Be sure that the bulkhead stake is not binding the pocket. NOTE: Make sure that all areas to be welded are clean and that bare metal is exposed before any welding is done. Figure 2 Weld Stake Pocket to Flatbed Along All Indicated Surfaces 1/4" Weld 4. Weld the stake pocket to the siderail to fix its position. Make sure that the bulkhead stake is square (90 ) to the flatbed siderail. Prime and paint the stake pocket and welds if necessary. 3
5 Aerolite Wraparound Bulkhead DOT Models 6. See Figure 3. Drill a 9/16" diameter hole through the rub rail, stake pocket, stake, and flatbed siderail on each side of the trailer. Install and tighten the 3-1/2" bolts, flat washers, lock washers, and nuts. Figure 3 1/2"-13 x 3-1/2" Bolt 1/2"-13 Nut 1/2"Flat Washer 1/2"Lock Washer 7. Tighten the 1-1/2" bolts at the four locations on the front of the bulkhead. CAUTION: Torque all the bolts to 125 foot-pounds using a torque wrench. 8. Run a bead of clear silicone between the flatbed top rail and the bottom of the bulkhead to achieve a water tight seal. (Silicone not furnished) 1. Be sure that all fasteners are kept tight to proper torque specifications. How to Maintain the Wraparound Bulkhead 2. Inspect for load shift damage and weld cracks. Reweld and grind as required. Aero Industries, Inc. R INDIANAPOLIS, IN Bradbury Ave., Indianapolis, IN FAX: OMAHA, NE. - I-80 & Highway 50 South, Omaha, NE FAX: STREETSBORO. OH State Route 14, Streetsboro, OH FAX: Aero Kit - BURLINGTON. ON Harvester Road, Burlington, ON. L7L 5V FAX: Aero Industries, Inc /27/2008 Rev. C 4
D.O.T. Bulkhead. Installation Instructions. Attention Dealers: Please give this manual to the customer when product is delivered.
Serving the Truck & Trailer Industry Since 1944 Meets D.O.T. Specifications Aero Industries, Inc. D.O.T. Bulkhead Installation Instructions Attention Dealers: Please give this manual to the customer when
More informationSide Kit: Commodities Hauler. OWNER'S MANUAL Installation, Safety, and Maintenance Instructions READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION
R Side Kit: Commodities Hauler OWNER'S MANUAL Installation, Safety, and Maintenance Instructions READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION I n d u s t r i e s, I n c. Indianapolis, IN -800-535-955
More informationRoll - N - Pull. OWNER'S MANUAL Installation Instructions and Parts List READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION
OWNER'S MANUAL Installation Instructions and Parts List READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION Attention Dealers: Please give these instructions to the customer when the product is delivered. Indianapolis,
More informationInstallation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN
More informationAdditional Instructions for 6" Drop
Serving the Truck & Trailer Industry Since 1944 Additional Instructions for 6" Drop Attention Dealers: Please give this manual to the customer when product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationSide Kick 2. Installation Instructions & Parts Lists. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Side Kick 2 Installation Instructions & Parts Lists Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call
More informationEasy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Model 9 10 Spring Flange Mount Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-3-94
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS STYLIZED RUNNING BOARD APPLICATION: 2011-2016 Ford Explorer PART NUMBER: 28-21170, 28-21175 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS 13MM
More informationRugby Manufacturing TB-8/10/12/14 Hoist Manual. Preface INSTALLATION & OPERATION MANUAL
Preface INSTALLATION & OPERATION MANUAL INTRODUCTION IMPORTANT!! Read this manual thoroughly prior to installation and operation. This manual outlines the installation and operation of a TB-Series hoist
More informationPlease read these Installation Instructions in their entirety prior to installing or operating this equipment.
2007-15 Chevy/GMC 1500 (Standard & Short Box) Please read these in their entirety prior to installing or operating this equipment. Serial Number This hitch is rated to 30,000 lbs. Gross Towing Weight and
More informationAir Lift. Kit Honda Prelude ( ) PERFORMANCE INSTALLATION GUIDE
Air Lift PERFORMANCE Kit 75532 Honda Prelude (1992-2001) Cover illustration may not depict actual kit. MN-542 (06708) ECR 6206 INSTALLATION GUIDE For maximum effectiveness and safety, please read these
More informationHR-520 HOIST. Installation & Operation Manual. To Be Filled In By Installer. Pump Installation And Operation Manual#: In Service Date: Dealer:
Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 Rugby 1-800-255-4345 DuraClass 1-800-533-0494 Crysteel HR-520 HOIST Installation & Operation Manual To Be Filled In By Installer Hoist
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationEasy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,
More informationINSTALLATION INSTRUCTION Rev A
INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationHR-540/HR-550 HOIST Installation & Operation Manual
Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 Rugby 1-800-255-4345 DuraClass 1-800-533-0494 Crysteel HR-540/HR-550 HOIST Installation & Operation Manual To Be Filled In By Installer
More informationKWIK-LOCK. Parts Lists FOR END DUMPS. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
FOR END DUMPS Serving the Truck & Trailer Industry Since 1944 KWIK-LOCK s Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationWARNING. BX Dodge Dart SE/SXT/GT/Limited Installation Instructions
BX2410 Attachment Tab Height: 14 Attachment Tab Width: 22 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products and accessories
More informationJeep Wrangler (JK)
89109 Rev B Suspension Systems RS66109BR5 and RS66109BR9 2007 2013 Jeep Wrangler 4 Door Sport and Rubicon Models (2 SPORT SYSTEM) Jeep Wrangler (JK) 2007-2013 89109 Rev B READ ALL INSTRUCTIONS THOROUGHLY
More informationLR-416, LR-165, LR-25 INSTALLATION AND OPERATION MANUAL
RUGBY MANUFACTURING CO. INDUSTRIAL PARK 515 1st STREET NE RUGBY, NORTH DAKOTA 58368 03 5753 LR-416, LR-165, LR-25 INSTALLATION AND OPERATION MANUAL To Be Filled In By Installer Hoist Installed: Hoist Serial
More informationInstallation Instructions 2019 Chevy and GMC 1500 Rear Bumper Product Number: E4050, E4051 Application: Chevy and GMC 1500 Trucks
IMPORTANT SAFETY GUIDE Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided the following warnings, safety precautions, installation
More informationSuspension Upgrade System RS66152 (Upper Adjustable Control Arms)
89152 Rev B Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) Fits 1997-2006 Jeep Wrangler (TJ / LJ). 89152 Rev B READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationInstallation Instructions READ THOROUGHLY BEFORE BEGINNING Signature Series Rail Kit Dodge Ram Trucks-all, including Mega-cabs
INDEX Failure to follow all of these instructions may result in death or serious injury!. GUIDELINES FOR MATCHING TOW VEHICLE AND TRAILER. Pages -. DRILLED AND BOLTED INSTALLATION FIGURE. Page 4. NO-DRILL,
More informationWARNING NOTICE CAUTION ASSEMBLY INSTRUCTIONS
MODEL 284 EZ-GLIDE SYSTEM 10' HIGH CUBE VAN DRIVER SIDE ALUMINUM DROP DOWN LADDER RACK ATTENTION Read and understand all instructions and warnings before operating or using this product. WARNING This product
More informationSuspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation)
88507 Rev G Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation) Jeep Wrangler (JK) 88507 Rev G READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE
More informationBX Chevy Equinox Installation Instructions
Attachment Tab Height: 16 Attachment Tab Width: 23 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are
More informationINSTALLATION INSTRUCTION 89400
INSTALLATION INSTRUCTION 89400 FOR RANCHO SUSPENSION SYSTEM RS66400B: 2012 RAM 1500 4WD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More information92-00 Civic/ Integra/ Del Sol/ Accord/ CRX
92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 90-97 Accord/ 92-95 CRX Front Kit Part No. 75440 www.airliftperformance.com Please read these instructions completely before proceeding with installation MN-513
More informationTECHNICAL PROCEDURE INTRAAX SUSPENSION SYSTEMS TABLE OF CONTENTS
TECHNICAL PROCEDURE INTRAAX SUSPENSION SYSTEMS SUBJECT: Shock Mount Replacement Procedures LIT NO: L724 (Supersedes AM11 Rev B and L594 Rev C) DATE: December 1999 TABLE OF CONTENTS PREPARATION FOR PROCEDURES
More informationINSTALLATION INSTRUCTIONS 88029
INSTALLATION INSTRUCTIONS 88029 FOR SUSPENSION SYSTEMS RS6503: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION REV F IMPORTANT NOTES! WARNING: This
More informationComfort Ride Shock absorber system part numbers 2450, 2460 and 2470 Installation Instructions
Comfort Ride Shock absorber system part numbers 2450, 2460 and 2470 Installation Instructions All specifications are subject to change without notice. MOUNTING FLANGE CENTER HOLE FRONT OF Item Qty Part
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fixed Bracket Bed Extender Titan (2016-) Bed Extender (999T7 W4100) Installation of this accessory requires installation of
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationPlease read these Installation Instructions in their entirety prior to installing or operating this equipment.
Please read these in their entirety prior to installing or operating this equipment. This hitch is rated to 30,000 lbs. Gross Towing Weight and 7,500 lbs. Tongue Weight Bolt Torque Specifications Torque
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2410 Attachment Tab Height: 14 Serial Number Attachment Tab Width: 22 Please read BOTH these and the General Information
More informationHYDRAULIC LANDING GEAR REPLACEMENT
Purpose This kit outlines the procedure to replace existing square hydraulic landing gear jacks, including square and round hydraulic, pin-less jacks. Square landing gear is no longer available. Required
More informationJeep Wrangler (JK) Present
Suspension System RS66110B (3 SPORT SYSTEM w/ Progressive Coil Springs Front & Rear) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT
More informationRZR WINCH KIT KIT P/N
RZR WINCH KIT KIT P/N 2878787; 2879334 Application All RZR Models except RZR XP Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationSuspension System RS6525 (B)
88525 Rev A Suspension System RS6525 (B) Requires coil spring kit RS80116 (B) or RS80118 (B) for a complete installation Ford Super Duty READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationSuspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
More informationWJ AUTO TRANS. ATLAS SHIFTER
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 8 1 1 302051 BASE- ATLAS TWIN STICK MOUNT 2 1 302080 STUD BOLT 1/2-13 X 7 B7 3 1 303120 Serrated-Flange Hex Locknut 1/2-13
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 MODULAR WHEEL TO WHEEL NERF STEP BARS APPLICATION: 2007-2018 Chevy Silverado / GMC Sierra 1500-2500-3500 Crew Cab (6.5 ft. bed) & Dual Rear Wheel (8ft. Bed) Excl. Classic PART
More informationSuspension System RS66102B
890 Rev A Suspension System RS660B ( SPORT SYSTEM) 0 JEEP MODELS EQUIPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFYCATION KIT RS70003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST CLERANCE ISSUE).
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: ¾, 7/8, 15/16 Drill Bits: 1/8, 9/16, 5/8 1-1/8 HOLE SAW Other Tools: Center Punch, Measuring Tape Installation Instructions 5 WARNING: Under no circumstances
More informationINSTALLATION INSTRUCTION 88094
INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 25-1/2 Attachment Tab Width: 24 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationRugby Manufacturing SR-Series Hoist Manual. Preface INSTALLATION & OPERATION MANUAL
Preface INSTALLATION & OPERATION MANUAL INTRODUCTION IMPORTANT!! Read this manual thoroughly prior to installation and operation. This manual outlines the installation and operation of an SR-series hoist
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. DH2400 (Long & Standard Box) Please read these in their entirety prior to installing or operating this equipment.
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2011-14 BMW Mini Cooper Countryman (Includes S) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 20 Please read BOTH these and the General Instructions prior to installing or operating this
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS Thrasher Board APPLICATION: 007-017 Chevy Silverado / GM Sierra / 1500-500-3500 Extended / Double / Crew Cab PART NUMBER: 8-8105, 8-81035 ITEM QUANTITY DESCRIPTION
More informationWARNING. BX Nissan Sentra S/SV/SR/SL Installation Instructions
Attachment Tab Height: 14 Attachment Tab Width: 22 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are
More informationCurrent Ford F150 Race Series R Rear Bumper Installation Instructions
2015 - Current Ford F150 Race Series R Rear Bumper Installation Instructions PREPARATION STEPS 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency
More informationSuspension System RS66107 / RS66107B
89107 Rev D Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST
More informationRequired tools General hand tools 21/64" drill bit Torque wrench Threadlocker Center punch
Slipper Spring Kit (part numbers 2560, 2570 and 2580) Item Qty Part number Description 1... 8... 350054-50...3/8-16 x 1" grade 8 self-tapping screw 2... 4... 350084-00...7/16-14 x 4" grade 5 3... 6...
More informationInstallation Instructions
Installation Instructions Important INSTALLATION REQUIRES WELDING to the unibody chassis by a qualified welder or metal fabricator. A bolt-on installation is not possible for this product. CHECK STEERING
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2011-15 BMW Mini Cooper Countryman (Includes S) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 20 Please read BOTH these and the General Instructions prior to installing or operating this
More informationJK HD Skid Plate for Rear Falcon Shocks
1 JK HD Skid Plate for Rear Falcon Shocks Kit # 36-07-01-300 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate
More informationMODEL TB-8, TB-10, TB-12, & TB-14 TRAILER HOIST INSTALLATION AND OPERATION MANUAL
TRUCK BODIES & EQUIPMENT INTERNATIONAL, Inc. Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 1-800-533-0494 090001 MODEL TB-8, TB-10, TB-12, & TB-14 TRAILER HOIST INSTALLATION AND OPERATION
More informationINSTALLATION INSTRUCTIONS
88553 Rev A INSTALLATION INSTRUCTIONS For Rancho Suspension System RS66553B: 2017-2011 Ford F250 / F350 Super Duty 4x4 2.5 Leveling Kit (Available in black only. Component in illustrations may be red for
More informationUniversal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401
INSTALLATION INSTRUCTIONS Universal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401 Your new Chief Universal Pitch-Adjustable Wall Mount (UPM-2401) is a quick disconnect mounting system with
More informationWARNING. BX HUMMER H 2 Installation Instructions. Serial Number
BX4102 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed
More informationStevens Type A/F Encoder. For Stand-Alone Encoder Part # AND Encoder Attachment Part # INSTRUCTION 90044
Stevens Type A/F Encoder For Stand-Alone Encoder Part # 90043 AND Encoder Attachment Part # 44903 INSTRUCTION 90044 Table of Contents SAFETY AND EQUIPMENT PROTECTION 3 1 INTRODUCTION... 5 1.1 GENERAL DESCRIPTION...
More informationRace Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE
Race Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE PARTS LIST (INCLUDED IN THE KIT) 1 x LED Control Center Box 2 x 48 RGB Aluminum Channel LED Bars 2 x 36 RGB Aluminum Channel LED Bars 1 x
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar
More information97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT
921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 WHEEL-TO-WHEEL NERF STEP BARS APPLICATION: 2009-2015 Ram 1500 Quad Cab (6 4 Bed) 2009-2018 Ram 1500 Crew Cab (5 7 Bed) PART NUMBER: 28-534310, 28-534315 CONTENT ITEM QUANTITY
More informationHIGH RISE POWER ANGLE KIT
HIGH RISE POWER ANGLE KIT P/N 33-0100 OWNER S MANUAL Application HIGH RISE PUSH TUBE 33-0000 & 34-0000 ATTENTION DEALER: CUSTOMER MUST RECEIVE A COPY OF THIS MANUAL AT THE TIME OF SALE. Before you begin,
More informationWD DODGE SUSPENSION LIFT KIT P/N
4/03/03 94-01 4WD DODGE 1500 3 SUSPENSION LIFT KIT P/N 10-46094 NOTE: Each lift kit, and options to lift kits, are packaged separately. Therefore installation procedures are covered in separate instructions.
More informationPRORAC CONTRACTOR SERIES UNIVERSIAL STEEL ECONO TRUCK RACK INSTALLATION INSTRUCTIONS
PRORAC CONTRACTOR SERIES UNIVERSIAL STEEL ECONO TRUCK RACK INSTALLATION INSTRUCTIONS 500 Lb. Capacity Package Contents: Parts Hardware (4) Legs (12) 3/8-16 x 1-1/4 Hex Head Bolts (36) Flat Washers (4)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS GASOLINE TRUCKS ONLY R7 STEP BOARD APPLICATION: 007-017 Chevy Silverado/GMC Sierra 1500/500/3500 Ext. / Double / Crew Cab PART NUMBER: 8-7100, 8-7105, 8-71030, 8-71035 ITEM QUANTITY
More informationInstallation Instructions/Operation and Maintenance Manual. PS DOORS Contact Information. Website psdoors.com
Rev. 110717 Ladder Safety Gate Installation Instructions/Operation and Maintenance Manual Models All Models: LSG-15 to LSG-48 Table of Contents Product Information...2 Inspection & Maintenance...2 Warranty
More informationInstallation Instructions
Important Parts Installation Instructions INSTALLATION REQUIRES WELDING by a qualified welder or metal fabricator. Weld-on installation is strongly recommended for maximum strength and reinforcement of
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. 2014-2017 Ram 2500 (All beds) Please read these in their entirety prior to installing or operating this equipment.
More information'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N
4/10/13 '88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N. 10-41888 INSTALLATION INSTRUCTIONS APPLICATION WARNING: Applicable for hub mounted ABS sensor models only. Not for 1992-94
More informationINSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK
INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK Load capacity: Up to 800 lbs. evenly distributed. Approximate Assembly and Installation Time: 60 min. (1 hr.) depending on truck
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH All Fasteners Typical, Both Sides WARNING: Under no circumstances
More informationPlease read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.
2015-18 Chevy Suburban/Tahoe 2015-18 GMC Yukon/Yukon XL (Includes Denali) Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products
More information11221 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-CURRENT MAKE: CHEVROLET MODEL: VOLT STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationInstallation Instructions
PIN BOX SHOWN ASSEMBLED Equipment Required: Fastener Kit: ST100F Wrenches: 15/16, 1 1/8 Drill Bits: Not Required White Lithium Grease, Torque Wrench Installation Instructions DEALER/INSTALLER: (1) Provide
More informationINSTALLATION INSTRUCTIONS WHEEL-TO- WHEEL
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS WHEEL-TO- WHEEL APPLICATION: 2009-2017 Dodge Ram 1500 Crew Cab 5.5 Bed 2009-2017 Dodge Ram 1500 Quad Cab 6.5 Bed PART NUMBER: 21-534310, 21-534315 ITEM QUANTITY
More informationINSTALLATION INSTRUCTION 88073
INSTALLATION INSTRUCTION 88073 Rev C FOR RANCHO SUSPENSION SYSTEMS RS6572 & RS6573: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2338 2012-17 Hyundai Accent GLS/SE (Includes Foglights) Attachment Tab Height: 14 Serial Number Attachment Tab Width:
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2009-15 Dodge Ram 1500 Sport/ST/Laramie Limited Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended
More informationINSTALLATION INSTRUCTIONS MOUNTING KIT COMMERCIAL TRUCK FOR 34 OUTSIDE FRAME WIDTH ONLY. Front of vehicle
INSTALLATION INSTRUCTIONS MOUNTING KIT COMMERCIAL TRUCK FOR 34 OUTSIDE FRAME WIDTH ONLY DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Save this Manual for future reference. (2) Pass
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN GRILLE GUARD / HDX GRILLE GUARD APPLICATION: 2016 Chevrolet Silverado 1500 PART NUMBER: 40-3875, 45-3870, 57-3870, 57-3875 ITEM QUANTITY DESCRIPTION
More informationRANGER MIDSIZE WINCH KIT
RANGER MIDSIZE WINCH KIT P/N 2881669 APPLICATION ALL MY RANGER 400; MY11 AND NEWER RANGER 500 EXCEPT CREW BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted
More informationDODGE / RAM 1500 *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY ***
6444 DODGE / RAM 500 6/8/207 OF 5 *** DO NOT EXCEED MANUFACTURER'S RECOMENDED TOWING CAPACITY *** ITEM QTY PART NUMBER 0 /2-3 x 2" 2 4 /2-3 x 3/4, GR8 3 4 CM-SP2 4 2 CM-SP6 5 4 HFN 23, GR8 6 2 CM-SP4 7
More informationNeon Front Kit Part No
EASYSTREET 1995-1999 Neon Front Kit Part No. 75588 www.airliftcompany.com MN-551 (07503) ECR 5014 Please read these instructions completely before proceeding with installation Warranty Information 1. All
More informationSuspension System RS6509B
88509 Rev H Requires the following for a complete installation: Quick disconnect end link kit RS6756B or solid end link kit RS6753B (for the Rubicon) Rancho exhaust kit RS720001 or RS720002 (or equivalent)
More informationCenter Drive Tube. Gussets
O P E R A T O R S M A N U A L EZ-GLIDE SYSTEM ALUMINUM DROP DOWN LADDER RACK Read and understand all WARNINGS, DANGERS, NOTICES and instructions before assembly and installation. WARNING MODEL 251-3-02,
More informationJeep Wrangler (JK) Present
89107 Rev H Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW REAR BUMPER APPLICATION: 2013-2018 Dodge Ram 1500 PART NUMBER: 58-81025 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 REAR BUMPER 18MM WRENCH 2 4 SENSOR L-TAB 5MM
More informationWARNING. BX Honda Civic (Includes Turbo) Installation Instructions
Attachment Tab Height: 12.5 Attachment Tab Width: 23 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products and accessories
More informationWARNING. BX Buick Lacrosse Installation Instructions. Bolt Torque Specifications. Bolt Torque Specifications
BX1515 Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers
More informationSUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS KIT P/N
SUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS KIT P/N 512-00010-00 CANOPY SUPPORTS INSTALLATION AND ADJUSTMENT Tools required: 1-7/8 open end wrench 1-3/4 open or box end wrench (or a rachet and 3/4 socket)
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing ADARAC Truck Bed Rack. Agri-Cover, Inc. proudly manufactured this product using superior quality materials and workmanship. With proper
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HDX LED GRILLE APPLICATION: 06-07 Toyota Tacoma PART NUMBER: 34-065 ITEM QUANTITY DESCRIPTION TOOLS NEEDED HDX GRILLE 0MM SOCKET 8 M6 HEX NUT (YELLOW ZINC) 3 8 M6 SPLIT LOCK WASHER
More information