Method of Aircraft Fuel Tank System Ignition Source Fail- Safe Feature Analysis
|
|
- Emery Bishop
- 6 years ago
- Views:
Transcription
1 Available online at Procedia Engineering 17 (2011 ) The 2nd International Symposium on Aircraft Airworthiness (ISAA 2011) Method of Aircraft Fuel Tank System Ignition Source Fail- Safe Feature Analysis ZHANG Yanjun *, SUN Youchao, WANG Fengchan, ZENG Haijun College of Civil Aviation, Nanjing University of Aeronautics and Astronautics,Nanjing ,P.R.China Abstract Fuel tank system ignition source failure threatens the safety of the aircraft. For different possible ignition sources in and around the fuel tank system and their airworthiness requirements, this paper proposes a particular method using both Failure Mode and Effects Analysis (FMEA) and Fault Tree Analysis (FTA) to analyze the ignition source failsafe features, which can minimize the hazards caused by the ignition sources failure and improve the safety of the whole aircraft. At last, an example is given, which proves the efficiency of the method Published by Elsevier Ltd. Open access under CC BY-NC-ND license. Selection and/or peer-review under responsibility of Airworthiness Technologies Research Center NLAA, and Beijing Key Laboratory on Safety of Integrated Aircraft and Propulsion Systems, China Keywords: Airworthiness,Fuel tank System, Ignition source, FMEA, FTA, Minimum cut, safety; 1. Introduction The fuel tank system ignition source failure is one of typical particular risks threatening aircraft. There are multiple accidents that due to the failure of ignition source in aviation history, even makes a catastrophic accident (such as TWA800 aircraft).hence, building up a method that may assess the safety of ignition source failure in the plane design stage is very instructive and meaningful to the design and research personnel and will minimize the hazard from the accidents. The Advisory Circular C[1] Fuel Tank Ignition Source Prevention Guidelines of Federal Aviation Administration provides the parts and components that would be ignition source and the design * Corresponding author. Tel.: address:zhangyj_204@163.com Published by Elsevier Ltd. doi: /j.proeng Open access under CC BY-NC-ND license.
2 ZHANG Yanjun et al. / Procedia Engineering 17 ( 2011 ) considerations, however, it doesn t contain the detailed assessment method of the fuel tank ignition source; In this paper, a particular method that can be used in the design stage to evaluate the safety of the fuel tank ignition source failure is proposed. 2. Definitions And Assumptions 2.1. Definitions Ignition source is a source of sufficient energy to ignite combustion of a fuel/air mixture. Surfaces that can exceed the auto-ignition temperature of the flammable vapour under consideration are considered to be ignition sources. Electrical arcs, electrical sparks and friction sparks are also considered ignition sources if sufficient energy is released to initiate combustion. Intrinsically safe is that any instrument, equipment, or wiring that is incapable of releasing sufficient electrical or thermal energy under normal operating conditions, anticipated failure conditions, and environmental conditions which could cause an ignition source within the fuel tank. Latent Failure is a failure whose presence may not be readily apparent to the flight crew or maintenance personnel. A significant latent failure is one that would, in combination with one or more specific failures or events result in a hazardous or catastrophic failure condition Assumptions The safety assessment for fuel tank system ignition source failure would be conducted based upon the following assumptions: 1) the analysis would assume that the environment inside the fuel tank is always flammable. The conditions required to ignite fuel vapors from ignition sources vary with pressures and temperatures within the fuel tank and can be affected by sloshing or spraying of fuel in the tank2) Unless design features are incorporated that mitigate the hazards resulting from a fuel tank ignition event (e.g. polyurethane foam, adequate structural margin), the safety assessment would assume that the presence of an ignition source is a catastrophic failure condition. 3. Fuel Tank System Ignition Source Fail-Safe Analysis 3.1. Possible Ignition Source This method is intended to analysis system failures that may result in the presence of an ignition source in the fuel tanks, and is not intended to analysis failures or conditions that could lead to ignition of fuel vapours from such sources as uncontained engine debris post crash fire heating of tank surfaces, etc. So the possible ignition sources [1] are as shown in table 1.
3 640 ZHANG Yanjun et al. / Procedia Engineering 17 ( 2011 ) Table 1. Possible ignition sources Failure Code Area Ignition Sources A1 Internal to the tank Electrical fuel pumps; FQGS(Fuel Quantity Gauging System); Bonding failure; Electrostatic charge; Hydraulics heater exchanger; A2 External to the tank Wiring routing and protection; Landing light; Bleed and anti-icing system lines; Electrical actuated/operated components of fuel system; Hydraulic system, etc. A3 Environmental Lightning/bonding; ignition sources EMI/HIRF; 3.2. Safety Requirements To Ignition Source Airplane fuel tank systems have a limited number of possible ignition sources. According to some related airworthiness regulations, it is required that no ignition source should be presented in the fuel tank or fuel tank system where catastrophic failure may occur due to ignition of fuel or vapors.three failure scenarios (shown in Fig 1) that must be addressed in order to show compliance with the rule[2]: (a) Each single failure, regardless of the probability of occurrence of the failure, must not cause an ignition source; (b) All combinations of failures not shown to be extremely improbable must not cause an ignition source; (c) Each single failure, regardless of the probability of occurrence, in combination with any latent failure condition not shown to be at least extremely remote (i.e. not shown to be extremely remote or extremely improbable), must not cause an ignition source. Fig. 1. Failure Modes of Ignition Sources 3.3. Ignition Source Fail-Safe Analysis To meet the requirements mentioned above, it needs to analyze a single failure with FMEA. An FMEA [3] is a systematic, bottom-up method of identifying the failure modes of a system, item, or function and determining the effects on the next higher level. It can be performed at any level within the system (e.g., piece-part, function, black box, etc.). For analyzing ignition sources fail-safe feature, FMEA may include the following information: Identification of component, signal, and/or function; Failure effects (directly
4 ZHANG Yanjun et al. / Procedia Engineering 17 ( 2011 ) and/or at the next higher level); Phase of flight in which the failure occurs; Severity of failure effects, etc. Table 2 shown below is a kind of FMEA worksheets. Table 2. FMEA Worksheet Part No. Part Type Failure Mode Hazard Type Comments After FMEA to the single failure to ensure that it will not cause an ignition source, it is necessary to analyze some combination of failures causing an ignition source that will not bring a catastrophic accident to the aircraft with FTA. A Fault Tree Analysis is a top-down system evaluation procedure in which a qualitative model for a particular undesired event is formed and then evaluated. The analyst begins with an undesired top level hazard event and systematically determines all credible single faults and failure combinations of the system functional blocks at the next lower level which could cause this event. The analysis proceeds down through successively more detailed (i.e., lower) levels of the design until a Primary Event is uncovered or until the top level hazard event requirement has been satisfied. A typical FTA is shown in Fig 2. Fig. 2. A Typical FTA The method to calculate the probability of the top event: a) When different minimum cuts don t contain the same basic event, the probability of the top event can be calculated with formula (1): k g( q) P ( T ) P ( K K K ) 1 (1 q (1) r r 1 2 h i ) j1 jkj In formula (1), Ki x1 x2 xm( i 1,2,, k) ; m is the number of basic event of the first j minimum cut K. j
5 642 ZHANG Yanjun et al. / Procedia Engineering 17 ( 2011 ) b) When different minimum cuts contain the same basic event, the probability of the top event can be calculated with formula (2): k n k1 qi qi ( 1) r1 ik r 1h jk ik hk j i1 g ( q) q (2) In formula (2), i is the ordinal number of the basic event; k is the number of the basic event; r, h, k are the ordinal number of the minimum cuts; i Kr means the first i basic event belongs to the first r minimum cut; K is the symbol of the minimum cut; i K h K means the first i basic event xi belongs to the first h minimum cut or the first j minimum cut; 1 h j k is the range of h and j. The steps of the analysis are as follows: Step1. Determine the ignition sources of the fuel tank system, including latent ignition source; Step2. Make it clear the requirements in the design rules, including related event content and maximum acceptable probability, etc; Step3. Analyze the possible ignition sources with FMEA and FTA qualitatively and quantitatively; Step4. Give out the conclusion about the fuel tank system ignition sources. The flowchart [6] of the analysis is shown in Fig 3: i j Fig. 3. Flowchart of the Analysis With the method mentioned above and the steps of the analysis, a program, which can be used to calculate the probability of the top event, especially at the early designing stage, when the whole FTA of the aircraft has not been built completely, is developed. It can help the designers to analysis ignition source fail-safe features easily.fig.4 is the main interface of the program. Fig.4.Main interface of analysis program
6 ZHANG Yanjun et al. / Procedia Engineering 17 ( 2011 ) An Example An analysis is performed on a type of aircraft fuel tank system. With the method and program above, first, the parts related to the fuel system that would be an ignition source are listed in the table, and the failure mode, failure effects and hazard type.etc. are analyzed, as shown in the table 3 below: Table 3. FMEA of the fuel tank system parts Part No. Part Type Failure Mode Hazard Type Comments P1 Boost pump Electrical arcing Electrical energy rising P2 P3 FQGS Harness protection Engine feed shutoff valve actuator energy at hazardous levels to enter fuel tank Electrical arcing from actuator Electrical Energy Rising and short circuit Short circuit Non-resettable thermal fuse imbedded in motor to prevent over temperature. No other power cables inside fuel tank Qualification tested to ensure explosion proof Then, the combinations of failures would be analyzed with FTA, and the minimum cuts would be calculated. The fuel tank system fault tree that ignition source would cause fire in fuel tank system is shown in Fig 5 and Table4. Fig. 5. Ignition Source FTA Table 4. FTA code and event definition Code Event definition Code Event definition T Fire in Fuel Tank System B2 Fuel Pipe Leak A1 Fuel Leak B3 Fuel Pipe Leak at Connectors A2 Ignition Source B4 Degradation of wire insulation B1 Fuel Tank Leak B5 Arcing Within Electrical Connectors
7 644 ZHANG Yanjun et al. / Procedia Engineering 17 ( 2011 ) With the program and using formula (1) in 3.3, the probability of the minimum cuts that would occur is shown in Fig.6. Fig. 6. Minimum Cuts and Probability of Events 5. Conclusion The method of aircraft fuel tank system ignition source fail-safe feature analysis with FMEA and FTA was proposed in this paper. Applying the proposed method, a type of aircraft fuel tank system ignition source was analyzed as an example. The results of the application example indicated the proposed methods are reasonable and efficient. Acknowledgements This research is supported by CAAC Science and Technology Project (MHRD200817). References [1]Advisory Circular AC C. Fuel Tank Ignition Source Prevention Guidelines[R].America: Federal Aviation Administration, 2008 [2]FAR-25. Part25-Airworthiness Standards: Transport Category Airplanes[S].America: Federal Aviation Administration, 2008 [3]SAE_ARP4761. Guidelines and methods for conducting the safety assessment process on airborne systems and equipments[s].america: The Engineering Society For Advancing Mobility Land Sea Air and Space, 1996 [4]FAR-23. Part23-Airworthiness Standards: Normal, Utility, Acrobatic, and Commuter Category Airplanes[S].America: Federal Aviation Administration, 2004 [5]Advisory Circular AC A. Fuel Tank Flammability Reduction means[r].america: Federal Aviation Administration, 2008 [6]XIONG Jun-jiang, LIU Bao-cheng, GAO Hong. On the Analysis and Design Method of System Safety[J].Journal of Beijing University of Aeronautics and Astronautics,2002,28: [7]FAA Document DOT/FAA/AR-98/26, Review of the Flammability Hazard of Jet A Fuel Vapor in Civil Transport Aircraft Fuel Tanks, June [8]CCAR-25-R4. Airworthiness Standards: Transport Category Airplanes[S].Civil Aviation Administration of China, 2008 [9]CCAR-23-R3. Airworthiness Standards: Normal, Utility, Acrobatic, and Commuter Category Airplanes[S]. Civil Aviation Administration of China, 2005
Aging Systems Workshop Fuel Tank Safety- FINAL RULE
Aging Systems Workshop Fuel Tank Safety- FINAL RULE November 8, 2001 Mike Dostert Transport Airplane Directorate Federal Aviation Administration Phone: 425-227-2132, E-Mail: mike.dostert dostert@faa.gov
More informationAvailable online at ScienceDirect. Procedia Engineering 137 (2016 ) GITSS2015
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 137 (2016 ) 244 251 GITSS2015 Simulation Analysis of Double Road Train Adaptability of Highway in China Hao Zhang a,b,*, Hong-wei
More informationExperimental Study on Overflow Pipe Structure of the Rod Pump with Down-hole Oil-water Hydrocyclone
Available online at www.sciencedirect.com Procedia Engineering 18 (2011) 387 391 The Second SREE Conference on Oil and Gas Engineering Experimental Study on Overflow Pipe Structure of the Rod Pump with
More informationExperimental Study on Inlet Structure of the Rod Pump with Down-hole Oil-water Hydrocyclone
Available online at www.sciencedirect.com Procedia Engineering 18 (2011) 369 374 The Second SREE Conference on Oil and Gas Engineering Experimental Study on Inlet Structure of the Rod Pump with Down-hole
More informationOptimization of PID Parameters of Hydraulic System of Elevating Wheelchair Based on AMESim Hui Cao a*, Hui Guo b
Available online at www.sciencedirect.com Procedia Engineering 15 (2011) 3710 3714 Advanced in Control Engineering and Information Science Optimization of PID Parameters of Hydraulic System of Elevating
More informationAccepted Means of Compliance; Airworthiness Standards: Normal Category. SUMMARY: This document announces the availability of 63 Means of Compliance
This document is scheduled to be published in the Federal Register on 05/11/2018 and available online at https://federalregister.gov/d/2018-09990, and on FDsys.gov [4910-13] DEPARTMENT OF TRANSPORTATION
More informationApplications of Frequency Conversion Technology in Aircompressor
Available online at www.sciencedirect.com Procedia Engineering 15 (2011) 944 948 Advanced in Control Engineeringand Information Science Applications of Frequency Conversion Technology in Aircompressor
More informationDesign and experiment of hydraulic impact loading system for mine cable bolt
Procedia Earth and Planetary Science 1 (2009) 1337 Procedia Earth and Planetary Science www.elsevier.com/locate/procedia The 6 th International Conference on Mining Science & Technology Design and experiment
More informationThe Impact of Common Rail System s Control Parameters on the Performance of High-power Diesel
Available online at www.sciencedirect.com Energy Procedia 16 (1) 67 7 1 International Conference on Future Energy, Environment, and Materials The Impact of Common Rail System s Control Parameters on the
More informationAvailable online at ScienceDirect. Physics Procedia 67 (2015 )
Available online at www.sciencedirect.com ScienceDirect Physics Procedia 67 (2015 ) 518 523 25th International Cryogenic Engineering Conference and the International Cryogenic Materials Conference in 2014,
More informationHydraulic Characteristic of Cooling Tower Francis Turbine with Different Spiral Casing and Stay Ring
Available online at www.sciencedirect.com Energy Procedia 16 (2012) 651 655 2012 International Conference on Future Energy, Environment, and Materials Hydraulic Characteristic of Cooling Tower Francis
More informationAvailable online at ScienceDirect. Procedia Engineering 129 (2015 ) International Conference on Industrial Engineering
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 129 (2015 ) 166 170 International Conference on Industrial Engineering Refinement of hybrid motor-transmission set using micro
More informationResearch of Driving Performance for Heavy Duty Vehicle Running on Long Downhill Road Based on Engine Brake
Send Orders for Reprints to reprints@benthamscience.ae The Open Mechanical Engineering Journal, 2014, 8, 475-479 475 Open Access Research of Driving Performance for Heavy Duty Vehicle Running on Long Downhill
More informationCRD - NPA 10/ April 2005 Page 1 of 15 I-B. CS 25J901 1 / F. Fagegaltier. Paragraph. 1. Agreed 2. Agreed
CRD - NPA 10/2004 Comment CS 25J901 1 / F. Fagegaltier 1 - The proposed 25.901 (a)(1) is close but is not identical to the definition of an APU in CS- Definitions. It is assumed that the intent is to refer
More informationParameters Matching and Simulation on a Hybrid Power System for Electric Bulldozer Hong Wang 1, Qiang Song 2,, Feng-Chun SUN 3 and Pu Zeng 4
2nd International Conference on Electronic & Mechanical Engineering and Information Technology (EMEIT-2012) Parameters Matching and Simulation on a Hybrid Power System for Electric Bulldozer Hong Wang
More informationSpecial Condition C-04 on Interaction of Systems and Structure on helicopters configured with Fly-by-Wire (FBW) Flight Control System (FCS)
Special Condition C-04 on Interaction of Systems and Structure on helicopters configured with Fly-by-Wire (FBW) Flight Control System (FCS) This Special Condition is published for public consultation in
More informationThe Study of Thermoelectric Power Generation in The Cooling of Fin and Vibration Heat Pipe
Available online at www.sciencedirect.com Energy Procedia 17 (212 ) 157 1577 212 International Conference on Future Electrical Power and Energy Systems The Study of Thermoelectric Power Generation in The
More informationPotential of Large Output Power, High Thermal Efficiency, Near-zero NOx Emission, Supercharged, Lean-burn, Hydrogen-fuelled, Direct Injection Engines
Available online at www.sciencedirect.com Energy Procedia 29 (2012 ) 455 462 World Hydrogen Energy Conference 2012 Potential of Large Output Power, High Thermal Efficiency, Near-zero NOx Emission, Supercharged,
More informationStaff Instruction. Ferry Fuel System Field Acceptance Criteria
Staff Instruction Subject: Ferry Fuel System Field Acceptance Criteria Issuing Office: Civil Aviation Activity Area: Qualifying Document No.: SI 500-020 File No.: A 5500-15-1 U Issue No.: 01 RDIMS No.:
More informationA starting method of ship electric propulsion permanent magnet synchronous motor
Available online at www.sciencedirect.com Procedia Engineering 15 (2011) 655 659 Advanced in Control Engineeringand Information Science A starting method of ship electric propulsion permanent magnet synchronous
More informationFederal Aviation Administration
Memorandum Federal Aviation Administration Date: To: From: Prepared by: Subject: Memo No.: Proposed See Distribution Manager, Transport Airplane Directorate, Aircraft Certification Service Victor Wicklund,
More informationSimulation Analysis of Certain Hydraulic Lifting Appliance under Different Working Conditions
Available online at www.sciencedirect.com Physics Procedia 25 (2012 ) 2268 2275 2012 International Conference on Solid State Devices and Materials Science Simulation Analysis of Certain Hydraulic Lifting
More informationThe Research on Optimal Design of Large Metallurgical Crane
Available online at www.sciencedirect.com Procedia Engineering 24 (211) 783 787 211 International Conference on Advances in Engineering The Research on Optimal Design of Large Metallurgical Crane Xianwen
More informationSensing of Diesel Vehicle Exhaust Gases under Vibration Condition
Available online at www.sciencedirect.com Procedia Environmental Sciences () 7 Sensing of Diesel Vehicle Exhaust Gases under Vibration Condition Chuliang Wei and Zhemin Zhuang, Qin Xin, A.I. Al-Shamma
More informationINTRODUCTION. Research & Reviews: Journal of Engineering and Technology. Research Article
Aircraft Fuel Manifold Design Substantiation and Additive Manufacturing Technique Assessment Using Finite Element Analysis Prasanna ND, Balasubramanya HS, Jyothilakshmi R*, J Sharana Basavaraja and Sachin
More informationA magnetic fluid seal for rotary blood pumps: Long-term performance in liquid
Physics Procedia 9 (2010) 229 233 Physics Procedia 00 (2010) 000 000 www.elsevier.com/locate/procedia www.elsevier.com/locate/procedia 12th International Conference on Magnetic Fluids A magnetic fluid
More informationAnalysis and Design of the Super Capacitor Monitoring System of Hybrid Electric Vehicles
Available online at www.sciencedirect.com Procedia Engineering 15 (2011) 90 94 Advanced in Control Engineering and Information Science Analysis and Design of the Super Capacitor Monitoring System of Hybrid
More informationGROUP WORKING WORKING PAPER. International FIRST MEETING. related tests SUMMARY. 1.1 independent. The DGP also may 1.2. The report, strategies. 1.
International Civil Aviation Organization 1. INTRODUCTION 1.1 At DGP/23 meeting, the Secretariat requested data on tests that have been conducted on lithium batteries. Since 2005 PRBA has contracted with
More informationResearch on Failure mode and effect analysis of Diesel Engine
Research on Failure mode and effect analysis of Diesel Engine Rahul Shrivastava¹, Alok Singh² ¹ Research Scholar, Dept. of Mechanical Engineering, M.A.N.I.T, Bhopal, M.P. India ²Assistant Professor, Dept.
More informationFAA Part 27 Rotorcraft Safety Continuum for Systems & Equipment
FAA Part 27 Rotorcraft Safety Continuum for Systems & Equipment Presented to: EASA Rotorcraft Symposium By: Andy Shaw Rotorcraft Standards Branch, FAA Date: December 5, 2017 Overview FAA Safety Continuum
More informationAvailable online at Procedia Engineering 45 (2012 )
Available online at www.sciencedirect.com Procedia Engineering 45 (2012 ) 830 835 2012 International Symposium on Safety Science and Technology Study on emergency response rank mode of flammable and explosive
More informationAvailable online at ScienceDirect. Procedia Engineering 129 (2015 ) International Conference on Industrial Engineering
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 129 (2015 ) 563 570 International Conference on Industrial Engineering Improved design of machine for cold cutting of oil pipes
More informationAC , Guidelines for the Certification, Airworthiness, and Operational Approval of Electronic Flight Bag Computing Devices.
Memorandum Date: Federal Aviation Administration To: From: Prepared by: See Distribution List David W. Hempe, Manager, Aircraft Engineering Division, AIR-100 Brad Miller, Avionic Systems Branch, AIR-130
More informationAnalysis on natural characteristics of four-stage main transmission system in three-engine helicopter
Article ID: 18558; Draft date: 2017-06-12 23:31 Analysis on natural characteristics of four-stage main transmission system in three-engine helicopter Yuan Chen 1, Ru-peng Zhu 2, Ye-ping Xiong 3, Guang-hu
More informationDynamic Characteristics Analysis of H-Type Leg Hydraulic System of. Truck mounted Concrete Pump
6th International Conference on Measurement, Instrumentation and Automation (ICMIA 2017) Dynamic Characteristics Analysis of H-Type Leg Hydraulic System of Truck mounted Concrete Pump Liu Huiyong1,a, Zhao
More informationHYDRAULIC ACTUATOR REPLACEMENT USING ELECTROMECHANICAL TECHNOLOGY
HYDRAULIC ACTUATOR REPLACEMENT USING ELECTROMECHANICAL TECHNOLOGY SCOPE This white paper discusses several issues encountered by Lee Air with past projects that involved the replacement of Hydraulic Actuators
More informationBond Graph Modeling and Simulation Analysis of the Electro-Hydraulic Actuator in Non-Load Condition
4th International Conference on Sensors, Mechatronics and Automation (ICSMA 2016) Bond Graph Modeling and Simulation Analysis of the Electro-Hydraulic Actuator in Non-Load Condition Liming Yu1, a, Hongfei
More informationThe Testing and Data Analyzing of Automobile Braking Performance. Peijiang Chen
International Conference on Computational Science and Engineering (ICCSE 2015) The Testing and Data Analyzing of Automobile Braking Performance Peijiang Chen School of Automobile, Linyi University, Shandong,
More informationAvailable online at ScienceDirect. Physics Procedia 67 (2015 )
Available online at www.sciencedirect.com ScienceDirect Physics Procedia 67 (2015 ) 1181 1186 25th International Cryogenic Engineering Conference and the International Cryogenic Materials Conference in
More informationImproved PV Module Performance Under Partial Shading Conditions
Available online at www.sciencedirect.com Energy Procedia 33 (2013 ) 248 255 PV Asia Pacific Conference 2012 Improved PV Module Performance Under Partial Shading Conditions Fei Lu a,*, Siyu Guo a, Timothy
More informationProposed Special Condition C-xx on Rudder Control Reversal Load Conditions. Applicable to Large Aeroplane category. Issue 1
Proposed Special Condition C-xx on Rudder Control Reversal Load Conditions Introductory note: Applicable to Large Aeroplane category Issue 1 The following Special Condition has been classified as an important
More informationDGINT/2. Flammability Reduction. Fuel tank safety. Purpose of the meeting. Review of conclusions from June 2004 workshop. Flammability Reduction
Flammability Reduction Fuel tank safety Flammability Reduction Purpose of the meeting Review of conclusions from June 2004 workshop Background Rulemaking framework for FTS Rulemaking task for FRS Ignition
More informationArchitecture Design For Smart Grid
Available online at www.sciencedirect.com Energy Procedia 17 (2012 ) 1524 1528 2012 International Conference on Future Electrical Power and Energy Systems Architecture Design For Smart Grid Yu Cunjiang,
More informationMuti-objective topology optimization of an electric vehicle s traction battery enclosure
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 88 (2016 ) 874 880 CUE2015-Applied Energy Symposium and Summit 2015: Low carbon cities and urban energy systems Muti-objective topology
More informationEasy Access Rules for Auxiliary Power Units (CS-APU)
CS-APU EASA erules: aviation rules for the 21st century Rules and regulations are the core of the European Union civil aviation system. The aim of the EASA erules project is to make them accessible in
More informationInternational Journal of Electronics and Computer Science Engineering 1119
International Journal of Electronics and Computer Science Engineering 1119 Available Online at www.ijecse.org ISSN- 2277-1956 SINGLE CURRENT PARAMETER METHOD OF CALIBRATION OF MINIATURE CIRCUIT Lakshay
More informationIntegrated Monitoring System Design of Hybrid Aircompressors
Available online at www.sciencedirect.com Procedia Engineering 15 (2011) 938 943 Advanced in Control Engineeringand Information Science Integrated Monitoring System Design of Hybrid Airs Huibin Liang a*,xuehua
More informationNational Transportation Safety Board Robert L. Swaim Aviation Engineering NRS. Fire Issues
Robert L. Swaim Aviation Engineering NRS Fire Issues October 23, 2001 The Safety Board has investigated aircraft fires since inception on April 1, 1967 BOAC 707 uncontained engine failure results in in-flight
More informationSPECIAL CONDITION. CS-22 Installation of electric propulsion units in powered sailplanes
CS- Doc. No. 14-Nov-014 Ref. CRI E-101 Page 1 of 11 Special Condition applicable to Powered Sailplanes equipped with Electric Propulsion Units Introductory note The hereby presented Special Condition has
More informationAn advisory circular may also include technical information that is relevant to the rule standards or requirements.
Revision 0 Electrical Load Analysis 2 August 2016 General Civil Aviation Authority advisory circulars contain guidance and information about standards, practices, and procedures that the Director has found
More informationCorrelation of Occupant Evaluation Index on Vehicle-occupant-guardrail Impact System Guo-sheng ZHANG, Hong-li LIU and Zhi-sheng DONG
07 nd International Conference on Computer, Mechatronics and Electronic Engineering (CMEE 07) ISBN: 978--60595-53- Correlation of Occupant Evaluation Index on Vehicle-occupant-guardrail Impact System Guo-sheng
More informationImproving Maintenance Safety Through Collaboration
Improving Maintenance Safety Through Collaboration IATA World Maintenance Symposium 23 September 2015 Presented by Christopher A. Hart, Chairman U.S. National Transportation Safety Board 1 Outline NTSB
More informationAvailable online at ScienceDirect. The Research about Fire Prevention of Vehicle Refuelling Stations.
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 71 ( 2014 ) 385 389 The Research about Fire Prevention of Vehicle Refuelling Stations Hong-yu Zhang* Kunming fire fighting school,
More informationAP Plant Operational Transient Analysis
www.ijnese.org International Journal of Nuclear Energy Science and Engineering Volume 3 Issue 2, June 2013 AP1000 1 Plant Operational Transient Analysis LIU Lixin 1, ZHENG Limin 2 Shanghai Nuclear Engineering
More informationAvailable online at ScienceDirect. Procedia Technology 21 (2015 ) SMART GRID Technologies, August 6-8, 2015
Available online at www.sciencedirect.com ScienceDirect Procedia Technology 21 (2015 ) 619 624 SMART GRID Technologies, August 6-8, 2015 Battery Charging Using Doubly Fed Induction Generator Connected
More informationFUEL TANK SAFETY / EWIS CONTINUATION TRAINING
FUEL TANK SAFETY / EWIS CONTINUATION TRAINING Q1 & 2 2017 Page 1 of 14 CONTENTS: 1 SFAR INTRODUCTION 2 Ground Fault Interrupters & Universal Fault Interrupters 3 EWIS Introduction 4 Related Airworthiness
More information2nd International Conference on Electronic & Mechanical Engineering and Information Technology (EMEIT-2012)
Analysis and Control of Shift Process for AMT without Synchronizer in Battery Electric Bus Sun Shaohua 1,a, LEI Yulong 1,b, Yang Cheng 1,c, Wen Jietao 1,d 1 State Key Laboratory of automotive simulation
More informationAvailable online at ScienceDirect. Procedia Engineering 68 (2013 ) 70 76
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 68 (2013 ) 70 76 Malaysian International Tribology Conference 2013 (MITC2013) The Effects of Oil Supply Pressure at Different
More informationFailure Modes and Effects Analysis for Domestic Electric Energy Meter Using In-Service Data
IOP Conference Series: Earth and Environmental Science PAPER OPEN ACCESS Failure Modes and Effects Analysis for Domestic Electric Energy Meter Using In-Service Data To cite this article: Ning Li et al
More informationThe design and implementation of a simulation platform for the running of high-speed trains based on High Level Architecture
Computers in Railways XIV Special Contributions 79 The design and implementation of a simulation platform for the running of high-speed trains based on High Level Architecture X. Lin, Q. Y. Wang, Z. C.
More informationPetroleum industries are dealing with different hazardous materials starting from storing, processing and distributing the petroleum products These he
FIRE SAFETY OF PETROLEUM INDUSTRIES By- Debapriya Biswas Additional Director General West Bengal Fire & Emergency Services Petroleum industries are dealing with different hazardous materials starting from
More informationScienceDirect. Modelling, Simulation and Control of a Foldable Stair Mechanism with a Linear Actuation Technique
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 97 (2014 ) 1312 1321 12th GLOBAL CONGRESS ON MANUFACTURING AND MANAGEMENT, GCMM 2014 Modelling, Simulation and Control of a
More informationAvailable online at ScienceDirect. Energy Procedia 36 (2013 )
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 36 (2013 ) 852 861 - Advancements in Renewable Energy and Clean Environment Introducing a PV Design Program Compatible with Iraq
More informationASSEMBLY 39TH SESSION
International Civil Aviation Organization WORKING PAPER 16/9/16 (Information paper) English only ASSEMBLY 39TH SESSION TECHNICAL COMMISSION Agenda Item 37: Other issues to be considered by the Technical
More informationDynamic analysis of ground steering response of aircraft with electric taxi system
Dynamic analysis of ground steering response of aircraft with electric taxi system Mingyang Huang 1, Hong Nie 2, Ming Zhang 3 1, 2, 3 Key Laboratory of Fundamental Science for National Defense-Advanced
More informationLow Emission Commercial Aircraft Engine Combustor Development in China:From Airworthiness Requirements to Combustor Design
Available online at www.sciencedirect.com Procedia Engineering 17 (2011) 618 626 The 2nd International Symposium on Aircraft Airworthiness (ISAA 2011) Low Emission Commercial Aircraft Engine Combustor
More informationPower Grid and Alternating Current Distribution Research of Renewable Energy Generate Electric Power s Village System
Available online at www.sciencedirect.com Energy Procedia 12 (2011) 328 334 ICSGCE 2011: 27 30 September 2011, Chengdu, China Power Grid and Alternating Current Distribution Research of Renewable Energy
More informationTHE APPLICATION OF WHOLE ENGINE FINITE ELEMENT MODEL ON CRITICAL SPEED ANALYSIS FOR THE COMMERCIAL AERO-ENGINE ROTOR
THE APPLICATION OF WHOLE ENGINE FINITE ELEMENT MODEL ON CRITICAL SPEED ANALYSIS FOR THE COMMERCIAL AERO-ENGINE ROTOR Huiying Song, Shaohui Wang, Kai Sun and Shoufeng Hu AVIC Commercial Aircraft Engine
More informationAvailable online at ScienceDirect. Procedia Engineering 170 (2017 )
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 170 (2017 ) 488 495 Engineering Physics International Conference, EPIC 2016 A Study on Integration of 1kW PEM Fuel Cell into
More information90. Ignition timing control strategy based on openecu design
90. Ignition timing control strategy based on openecu design Xianzheng Ling 1, Changshui Wu 2, Yangbo Liu 3, Sheng Lu 4 Shanghai University of Engineering and Science, Shanghai, China 1 Corresponding author
More informationRemote Area Hybrid Solar-Diesel Power Systems in Tropical Australia
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 57 (2014 ) 1485 1491 2013 ISES Solar World Congress Remote Area Hybrid Solar-Diesel Power Systems in Tropical Australia Anil Chaudhary
More informationNotification of a Proposal to issue an Airworthiness Directive
Notification of a Proposal to issue an Airworthiness Directive PAD No.: 18-143 Issued: 24 October 2018 Note: This Proposed Airworthiness Directive (PAD) is issued by EASA, acting in accordance with Regulation
More informationAvailable online at ScienceDirect. Procedia Engineering 150 (2016 )
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 150 (2016 ) 1291 1296 International Conference on Industrial Engineering, ICIE 2016 Energy Datum of the Flow of Exhaust Gases
More informationKey Parameters Investigation on Small Cycle Fuel Injection Quantity for a Diesel Engine Electronic Unit Pump System
Page63 EVS25 Shenzhen, China, Nov 5-9, 21 Key Parameters Investigation on Small Cycle Fuel Injection Quantity for a Diesel Engine Electronic Unit Pump System Abstract Liyun Fan 1, Bingqi Tian 1, and Xiuzhen
More informationAvailable online at ScienceDirect. Energy Procedia 110 (2017 )
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 110 (2017 ) 210 215 1st International Conference on Energy and Power, ICEP2016, 14-16 December 2016, RMIT University, Melbourne,
More informationSubject: INFORMATION: Policy Statement on Process for Developing SFAR 88-related Instructions for Maintenance and Inspection of Fuel Tank Systems
U.S. Department of Transportation Federal Aviation Administration Memorandum Subject: INFORMATION: Policy Statement on Process for Developing SFAR 88-related Instructions for Maintenance and Inspection
More informationSubj: HYDROGEN AND IGNITION ENERGY HAZARDS IN PASSENGER SUBMERSIBLES
Date: 08 March 1996 SSIC: 16703/46 CFR 183.05-20 MTN: 1-96 Subj: HYDROGEN AND IGNITION ENERGY HAZARDS IN PASSENGER SUBMERSIBLES Ref: (a) Navigation and Vessel Inspection Circular No. 5-93 (NVIC 5-93),
More informationAvailable online at ScienceDirect. Procedia Engineering 91 (2014 )
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 91 (2014 ) 459 463 XXIII R-S-P seminar, Theoretical Foundation of Civil Engineering (23RSP) (TFoCE 2014) Comparison of the Skid
More informationDEPARTMENT OF THE AIR FORCE HEADQUARTERS AIR FORCE LIFE CYCLE MANAGEMENT CENTER WRIGHT-PATTERSON AIR FORCE BASE OHIO
DEPARTMENT OF THE AIR FORCE HEADQUARTERS AIR FORCE LIFE CYCLE MANAGEMENT CENTER WRIGHT-PATTERSON AIR FORCE BASE OHIO BULLETIN AWB 330 12 DEC 2017 United States Air Force (USAF) Airworthiness Bulletin (AWB)-330
More informationAvailable online at ScienceDirect. Procedia CIRP 33 (2015 )
Available online at www.sciencedirect.com ScienceDirect Procedia CIRP 33 (2015 ) 581 586 9th CIRP Conference on Intelligent Computation in Manufacturing Engineering - CIRP ICME '14 Magnetic fluid seal
More informationThe spray characteristic of gas-liquid coaxial swirl injector by experiment
The spray characteristic of gas-liquid coaxial swirl injector by experiment Chen Chen 1,2, Yan Zhihui 2, Yang Yang 2, Gao Hongli 1, Yang Shunhua 2 and Zhang Lei 2 1 School of Mechanical Engineering, Southwest
More information[Docket No. FAA ; Directorate Identifier 2016-NE-09-AD] Airworthiness Directives; Pratt & Whitney Division Turbofan Engines
This document is scheduled to be published in the Federal Register on 04/20/2016 and available online at http://federalregister.gov/a/2016-09122, and on FDsys.gov [4910-13-P] DEPARTMENT OF TRANSPORTATION
More informationEU Mutual Recognition Technical Requirements
1. PRODUCT DESCRIPTION... 1 1.a General description of the product... 1 1.b Application limitations... 1 1.c Intended use... 2 1.d System context... 2 2. DESIGN EVALUATION... 2 2.a Engineering evaluation
More informationAnalytical impact of the sliding friction on mesh stiffness of spur gear drives based on Ishikawa model
Analytical impact of the sliding friction on mesh stiffness of spur gear drives based on Ishikawa model Zhengminqing Li 1, Hongshang Chen 2, Jiansong Chen 3, Rupeng Zhu 4 1, 2, 4 Nanjing University of
More informationPassive Vibration Reduction with Silicone Springs and Dynamic Absorber
Available online at www.sciencedirect.com Physics Procedia 19 (2011 ) 431 435 International Conference on Optics in Precision Engineering and Nanotechnology 2011 Passive Vibration Reduction with Silicone
More informationExtension of the Lower Load Limit in Dieseline Compression Ignition Mode
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 75 (2015 ) 2363 2370 The 7 th International Conference on Applied Energy ICAE2015 Extension of the Lower Load Limit in Dieseline
More informationAvailable online at ScienceDirect. Procedia Engineering 129 (2015 ) International Conference on Industrial Engineering
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 129 (2015 ) 201 206 International Conference on Industrial Engineering Simulation of lithium battery operation under severe
More informationChapter 2 Analysis on Lock Problem in Frontal Collision for Mini Vehicle
Chapter 2 Analysis on Lock Problem in Frontal Collision for Mini Vehicle Ce Song, Hong Zang and Jingru Bao Abstract To study the lock problem in the frontal collision test on a kind of mini vehicle s sliding
More informationAdvances in Engineering Research (AER), volume 102 Second International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2017)
Advances in Engineering Research (AER), volume 102 Second International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2017) Vibration Characteristic Analysis of the Cross-type Joint
More informationThe Test System Design and Actual Test of Motor Axis Torque During Seamless Steel Tube Rolling
Sensors & Transducers 2013 by IA http://www.sensorsportal.com The Test System Design and Actual Test of Motor Axis Torque During Seamless Steel Tube Rolling 1 Hong-Yu Liu, 1 Ze-Ning Xu, 2 Jun-Jie Xi 1
More informationOptimum Matching of Electric Vehicle Powertrain
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 88 (2016 ) 894 900 CUE2015-Applied Energy Symposium and Summit 2015: Low carbon cities and urban energy systems Optimum Matching
More informationA study on aerodynamic drag of a semi-trailer truck
Available online at www.sciencedirect.com Procedia Engineering 56 (013 ) 01 05 5 th BSME International Conference on Thermal Engineering A study on aerodynamic drag of a semi-trailer truck Harun Chowdhury*,
More informationCertification Memorandum. CS 27/ Safety considerations covering External Loads
Certification Memorandum CS 27/29.865 Safety considerations covering External Loads EASA CM No.: CM HS-004 Issue 01 issued 25 July 2016 Regulatory requirement(s): CS 27.865; CS 29.865 and related AC material
More informationADVANCES in NATURAL and APPLIED SCIENCES
ADVANCES in NATURAL and APPLIED SCIENCES ISSN: 1995-0772 Published BYAENSI Publication EISSN: 1998-1090 http://www.aensiweb.com/anas 2017 April 11(4): pages 544-550 Open Access Journal Analysis Of Sliding
More informationStudy on Flow Characteristic of Gear Pumps by Gear Tooth Shapes
Journal of Applied Science and Engineering, Vol. 20, No. 3, pp. 367 372 (2017) DOI: 10.6180/jase.2017.20.3.11 Study on Flow Characteristic of Gear Pumps by Gear Tooth Shapes Wen Wang 1, Yan-Mei Yin 1,
More informationA Device for Sorting and Recycling Dry Batteries Automatically Jiahang Xia
Advances in Computer Science Research (ACSR), volume 73 7th International Conference on Education, Management, Information and Computer Science (ICEMC 2017) A Device for Sorting and Recycling Dry Batteries
More informationReliability determination of ignition system of rocket platform using reliability block diagram and FMEA analysis
Reliability determination of ignition system of rocket platform using reliability block diagram and FMEA analysis Narongkorn Dernlugkam, Parkpoom Chokchairungroj Defence Technology Institute (Public Organisation)
More informationResearch on vibration reduction of multiple parallel gear shafts with ISFD
Research on vibration reduction of multiple parallel gear shafts with ISFD Kaihua Lu 1, Lidong He 2, Wei Yan 3 Beijing Key Laboratory of Health Monitoring and Self-Recovery for High-End Mechanical Equipment,
More informationResearch on Optimization of Bleed Air Environment Control System of Aircraft Xin-ge WANG, Han BAO* and Kun-wu YE
2017 International Conference on Electronic, Control, Automation and Mechanical Engineering (ECAME 2017) ISBN: 978-1-60595-523-0 Research on Optimization of Bleed Air Environment Control System of Aircraft
More informationOpen Access The New Structure Design and Simulation of Preventing Electric Shock Multi-Jacks Socket
Send Orders for Reprints to reprints@benthamscience.ae The Open Electrical & Electronic Engineering Journal, 2015, 9, 427-431 427 Open Access The New Structure Design and Simulation of Preventing Electric
More information