80CH SEGMENT/COMMON DRIVER FOR DOT MATRIX LCD
|
|
- Anthony Hart
- 6 years ago
- Views:
Transcription
1 80C SEGENT/COON DRIVER FOR T ATRIX CD INTRODUCTION 100 QFP KS0083/84 is a graphic type CD driver Sl which is fabricated by COS process for high voltage. In case of segment driver, can be selected 4 bit, 1 bit data transfer or chip select mode. KS0084 is reverse type of KS0083 FUNCTION Dot matrix CD driver with 80 channel output. lnput/output - Output: 80 channel waveform for CD driving - Intput: parallel display data and control signal from controller bias voltage (V 3, V 4, V SS, V EE ) FEATURES Power supply voltage: + 5V±10% (V DD) CD driving voltage: -24V(typ) (V EE) Interface type 1 type 2 type 3 COON SEGENT COON SEGENT COON SEGENT KS0083/84 KS0083/84 KS0103 KS0083/84 KS0083/84 KS0104/B KS0086 KS0086 KS0086 KS0086 l00qfp and bare chip available BOCK DIAGRA SC1 SC80 V 3 V 4 V SS Voltage Selector Analog Switch V EE evel Converter V DD V SS Data atch - DI 4 4 shift clock Shift Register Control ogic END count serial data Tx FCS ode select Fig. 1 KS0083/84 functional block diagram.
2 80C SEGENT/COON DRIVER FOR T ATRIX CD PIN CONFIGURATION SC 80 SC 79 SC 78 SC 77 SC 76 SC 75 SC 74 SC 73 SC 72 SC 71 SC 70 SC 69 SC 68 SC 67 SC 66 SC 65 SC 64 SC 63 SC 62 SC 61 SC 60 SC 59 SC 58 SC 57 SC 56 SC 55 SC 54 SC 53 SC 52 SC 51 V SC 50 V EE SC 49 FCS SC SC SC 46 V DD SC SC SC 43 V SS DI KS SC 42 SC 41 V SS DI SC 40 DI SC SC 38 NC SC SC 36 V SS SC 35 V SC SC 33 SC SC 32 SC 2 SC 3 SC 4 SC 5 SC 6 SC 7 SC 8 SC 9 SC 10 SC 11 SC 12 SC 13 SC 14 SC 15 SC 16 SC 17 SC 18 SC 19 SC 20 SC 21 SC 22 SC 23 SC 24 SC 25 SC 26 SC 27 SC 28 SC 29 SC 30 SC Fig QFP Top View
3 80C SEGENT/COON DRIVER FOR T ATRIX CD PIN CONFIGURATION SC SC SC 33 V SC 34 V SS SC SC 36 NC SC 37 D SC 38 D 12 D KS SC 39 SC 40 D V SS V SS SC SC SC SC 44 V DD SC SC SC 47 FCS SC 48 V EE SC 49 V SC SC 80 SC 79 SC 78 SC 77 SC 76 SC 75 SC 74 SC 73 SC 72 SC 71 SC 70 SC 69 SC 68 SC 67 SC 66 SC 65 SC 64 SC 63 SC 62 SC 61 SC 60 SC 59 SC 58 SC 57 SC 56 SC 55 SC 54 SC 53 SC 52 SC 51 SC 2 SC 3 SC 4 SC 5 SC 6 SC 7 SC 8 SC 9 SC 10 SC 11 SC 12 SC 13 SC 14 SC 15 SC 16 SC 17 SC 18 SC 19 SC 20 SC 21 SC 22 SC 23 SC 24 SC 25 SC 26 SC 27 SC 28 SC 29 SC 30 SC 31 Fig.3 100QFP Top View.
4 80C SEGENT/COON DRIVER FOR T ATRIX CD PIN FUCTIONA DESCRIPTION PIN INPUT OUTPUT DESCRIPTION INTERFACE Power V SS GND(0V) Supply V EE Power CD drivingvoltage (typ.-24v) V DD Internal logic driving voltage (typ.-5v) V 3,V 4 Input Bias Voltage input for CD drive: Non-selct evel (ust maintain CD >V3>V4>VEE.) SC 1 ~ SC 80 Output CD driver output terminal (80 Channel) CD FCS, Input ode select inputs. (refer to application circuit) FCS Com/Seg driver Input mode Segment driver Segment driver Segment driver Common driver 1 bit serial input 4 bit parallel input 1 bit serial input Serial input Chip select mode - In case of serial input mode, DI1 is data input pin and is data output pin - In case of 4 bit parallel input mode, Data input and output are; X O X O Output O O SC 1, SC 5,... SC 77 DI 2 SC 2, SC 6,... SC 78 DI 3 SC 3, SC 7,... SC 70 DI 4 SC 4, SC 8,... SC 80 - In case of the common driver, the data transfer clock is - Non-used data input pins are set to V SS or V DD to minimize current consumption
5 80C SEGENT/COON DRIVER FOR T ATRIX CD PIN DESCRIPTION (continued), PIN INPUT OUTPUT Input Output Input/Output for Chip Select. DESCRIPTION 1) becomes low by (, ) timing. 2) When IG data is input to, the device becomes select mode and reads input data at falling timing. Synchronized at the fall of. Input data is shifted. 3) After reading 80 input data(equivalent to 80 clock cycle in the serial mode or 20 clock cycles in the 4 bit parallel,mode), automatically becomes IG level and data reading is complete. is reset 1.5 cycles later. 4) When two or more devices are used in the chip select mode, of each state is connected to of the next state. (1) of all device connected is reset and device becomes nonselect state and waits for input after the previous 1). (2) When IG level is input to the first in the cascade connection, the first device performs the operation in 2) and 3). (3) When of the second device is connected to of the first device, the second device perform the operations 2) and 3) after the first device. This operation is repeated in the same method subsequently Input CD waveform AC conversion signal input atch data (non-select) (select) SC V 3 V 4 GND V EE atch data (non-select) (select) SC V 3 V 4 V EE GND INTERFACE Controller or KS0083/84 Controller (segment signal drive mode) (common signal drive mode) Input Clock pulse input terminal for data latch Controller Input Clock pulse input terminal for data shift Controller DI1 ~ DI4 Input Display data input from the CD controller SI. Controller In case of the common driver mode or serial input mode, supply the input data to DI1 and DI2 ~ DI4 have to be set to V SS level or V DD level. Output is high level in the chip select mode KS0083/84 NC Non-Connection NC
6 80C SEGENT/COON DRIVER FOR T ATRIX CD AXIU ABSOUTE IIT Characteristic Symbol Value Unit Operating Voltage V DD -7 ~ +0.3 Driver Supply Voltage V CD -30 ~ +0.3 V Input Voltage V IN V DD-0.3 ~ +0.3 Operating Temperature T OPR - 30 ~ + 85 C Storage Temperature T STG - 55 ~ +150 * Voltage greater than above may damage to the circuit. aximum absolute ilmits are those values beyond which permanent damage to the device may occur. These are stress ratings only and functional operation of the device beyond them is not implied. ong exposure to these conditions may affect device reliability. EECTRICA CARACTERISTICS DC Characteristics(V DD= -5V±10%, Vss=0V, V EE= -24V ±V, Ta=-30 ~ +85 C) Characteristiec Symbol Condition in Typ ax Unit Operating Current I DD 1 bit serial (3.3z) ma 4 bit parallel (2.0z) ma Input Voltage igh I I - 0.2V DD - - V ow I I V DD V Output Voltage igh I O I O=-0.4mA V ow I O I O=0.4mA - - V DD+0.4 V Voltage V D1 I ON=1mA for one of SCi V Descending (Vi-SCi) V D2 I ON=0.08mA for each SCi V eakage Current Input I KG µa Output I O(KG) µa
7 80C SEGENT/COON DRIVER FOR T ATRIX CD AC Characteristics (V DD=-5V±10%, V SS=0V, V EE=-24V±3V; Ta=-30 ~ +85 C) (1) Segment driver1; 1 bit serial data input (=ow, FCS=ow) (refer to: Fig. 3) Characteristic Symbol condition in ax Unit Clock Cycle Time t CY Clock Pulse Width igh evel t WCK ow evel t WCK Set Up Time D Before é t SU old Time D After é t ns Clock argin Time 1 t C (From éto é) Clock argin Time 2 t C (From éto é) Clock argin Time 3 t C (From èto è) Clock Rise/Fall Time t R, t F Output Delay Time t D C =15pF igh evel atch Clock Width t W Overlap Time Of And t OV (2) segment driver; 4 bit data input (=igh, FCS=ow) (refer to: fig. 4) Characteristic Symbol condition in ax Unit Clock Cycle Time t CY Clock Pulse Width igh evel t WCK ow evel t WCK Set Up Time D Before t SU old Time D After t ns Clock argin Time 1 t C (From éto ) Clock argin Time 2 t C (From éto ) Clock argin Time 3 t C (From èto ) Clock Rise/Fall Time t R, t F - 50 Output Delay Time t D C =15pF 230 igh evel atch Clock Width t W Overlap Time Of And t OV
8 80C SEGENT/COON DRIVER FOR T ATRIX CD (3) Common Driver (=igh, FCS=igh) (refer to: Fig. 5) Characteristic Symbol condition in ax Unit Clock Cycle Time t CY Clock Pulse Width igh evel t WCK ow evel t WCK Set-Up Time D before CK t SU old Time D after CK t ns Output Delay Time t D C =15pF Clock Rise/Fall Time t R, t F (4) segment driver 2; 1 bit serial data input (=ow, FCS=igh) (refer to: Fig. 6) Characteristic Symbol condition in ax Unit Clock Cycle Time t CY Clock Pulse Width igh evel t WCK ow evel t WCK Set Up Time D Before CK t SU old Time D After CK t ns Clock argin Time 1 t C (From To ) Clock argin Time 2 t C (From To ) Clock argin Time 3 t C (From To ) Clock Rise/Fall Time t R, t F - 50 Output Delay Time t D C =15pF 230 igh evel atch Clock Width t W Overlap Time Of And t OV NOTE : Input frequency, I/O reference level; 0.8V DD, 0.2V DD 1; Valid time (internal shift register) 2; (t cx1.5)-(t C1)-(t C3)-(t Rx3) TIING CARACTERISTICS
9 80C SEGENT/COON DRIVER FOR T ATRIX CD t WCK t WCK ó t R t F t SU t Valid t OV t W t D t C3 t R t C2 t C1 t F ó t W SC 1 ~ SC 80 Fig. 3 Segment driver ( 1 bit serial input ) t WCK t WCK ó t R t F ~ DI 4 t SU t t W tc3 t R t C2 t C1 t F t SU t ó t W t D t D t D ó SC 1 ~ SC 80 Fig bit input segment driver Fig. 4. Segment driver (4 bit input)
10 80C SEGENT/COON DRIVER FOR T ATRIX CD TIING CARACTERISTICS(continued) t WCK t WCK t R t F 0.2V DD 0.8V DD t SU t Valid t D SC 1 ~ SC 80 Fig. 5. Common driver t WCK t WCK 0.2V DD 0.8V DD ó t F t R t SU t t 0V t W tc3 t R t C2 t F t C1 t SU t ó t W t D t D t D ó SC 1 ~ SC 80 Fig. 6. Segment driver ( 1 bit serial data input )
11 80C SEGENT/COON DRIVER FOR T ATRIX CD APPICATION CIRCUIT ode Select 1. segment driver 1;1 bit serial data input (FCS=, =) 2. segment driver;4 bit serial data input (FCS=, =) CD PANE CD PANE from CD controller SC1 - SC80 KS0083/84 KS0083/84 from CD controller KS0083/84 DI1 DI2 DI3 DI4 KS0083/84 DI1 DI2 DI3 DI4 Display data 3. segment driver 2;1 bit serial data input (FCS=, =) 4. common driver (FCS=, =) from CD CD PANE controller Disply data SC 1 KS0083/84 SC 80 from CD controller KS0083/84 KS0083/84 CD PANE SC 1 Disply data KS0083/84 SC 80
12 80C SEGENT/COON DRIVER FOR T ATRIX CD - 5V - 5V SC 1 - SC 80 SC 1 - SC 80 KS0083/84 KS0083/84 KS0083/84 KS0083/84 KS0083/84 KS0083/84 KS0083/84 KS0083/84 SC SC KS0083/84 KS0083/84 CK 2 CK 1 CK 2 CK 1 controller YD C2 C1 VD SC VSC CK DI1 DI2 DI3 DI4 D 0 - D 7 ± CD PANE ² ³ 0V
13 80C SEGENT/COON DRIVER FOR T ATRIX CD APPICATION CIRCUIT DIAGRA SC1 SC2 SC3 SC4 SC5 SC6 SC7 SC8 SC9 SC10 SC80 SC79 SC78 SC77 SC76 SC75 SC74 SC73 SC72 SC71 SC11 SC12 SC13 SC70 SC69 SC68 SC14 SC15 SC16 SC17 SC18 SC19 SC20 SC21 SC22 SC23 SC24 SC25 SC67 SC66 SC65 SC64 SC63 SC62 SC61 SC60 SC59 SC58 SC57 SC56 * KS0083 SC26 arking : easy to find the SC3 SC27 SC28 SC29 SC55 SC54 SC53 SC52 SC30 SC31 SC32 SC33 SC34 SC35 SC36 SC37 SC38 SC39 SC40 SC41 SC42 SC43 SC44 SC45 SC46 SC47 SC48 SC49 SC50 SC51 V4 DI1 DI2 DI3 DI4 VDD FCS VEE V3 KS0083 Y (0,0) X CIP SIZE : SIZE : UNIT : ìm
14 80C SEGENT/COON DRIVER FOR T ATRIX CD OCATION NAE NAE NAE NUBER NUBER NUBER COORDINATE COORDINATE COORDINATE Y Y X X Y X SC69 SC70 SC71 SC72 SC73 SC74 SC75 SC76 SC77 SC78 SC79 SC80 V3 VEE FCS VDD DI4 DI3 DI2 DI1 V4 SC SC2 SC3 SC4 SC5 SC6 SC7 SC8 SC9 SC10 SC11 SC12 SC13 SC14 SC15 SC16 SC17 SC18 SC19 SC20 SC21 SC22 SC23 SC24 SC25 SC26 SC27 SC28 SC29 SC30 SC31 SC32 SC33 SC34 SC SC36 SC37 SC38 SC39 SC40 SC41 SC42 SC43 SC44 SC45 SC46 SC47 SC48 SC49 SC50 SC51 SC52 SC53 SC54 SC55 SC56 SC57 SC58 SC59 SC60 SC61 SC62 SC63 SC64 SC65 SC66 SC67 SC
15 80C SEGENT/COON DRIVER FOR T ATRIX CD DIAGRA SC80 SC79 SC78 SC77 SC76 SC75 SC74 SC73 SC72 SC71 SC1 SC2 SC3 SC4 SC5 SC6 SC7 SC8 SC9 SC10 SC70 SC69 SC68 SC11 SC12 SC13 SC67 SC66 SC65 SC64 SC63 SC62 SC61 SC60 SC59 SC58 SC57 SC56 SC55 SC14 SC15 SC16 SC17 SC18 SC19 SC20 SC21 SC22 SC23 SC24 SC25 SC26 * KS0084 SC54arking : easy to find the SC3. SC53 SC52 SC27 SC28 SC29 SC51 SC50 SC49 SC48 SC47 SC46 SC45 SC44 SC43 SC42 SC41 SC40 SC39 SC38 SC37 SC36 SC35 SC34 SC33 SC32 SC31 SC30 V3 VEE FCS VDD C1 D4 D3 D2 D1 C2 V4 KS0084 Y (0,0) X CIP SIZE : SIZE : UNIT : ìm
16 80C SEGENT/COON DRIVER FOR T ATRIX CD OCATION. NAE NAE NAE NUBER NUBER NUBER COORDINATE COORDINATE COORDINATE Y Y X X Y X SC13 SC12 SC11 SC10 SC9 SC8 SC7 SC6 SC5 SC4 SC3 SC2 SC1 V4 C2 D1 D2 D3 D4 C1 VDD FCS VEE V SC46 SC45 SC44 SC43 SC42 SC41 SC40 SC39 SC38 SC37 SC36 SC35 SC34 SC33 SC32 SC31 SC30 SC29 SC28 SC27 SC26 SC25 SC24 SC23 SC22 SC21 SC20 SC19 SC18 SC17 SC16 SC15 SC14 SC67 SC SC80 SC79 SC78 SC77 SC76 SC75 SC74 SC73 SC72 SC71 SC70 SC69 SC68 SC67 SC66 SC65 SC64 SC63 SC62 SC61 SC60 SC59 SC58 SC57 SC56 SC55 SC54 SC53 SC52 SC51 SC50 SC49 SC48 SC
80 SEGMENT DRIVER FOR DOT MATRIX LCD S6A2067
80 SEGENT DRIVER FOR DOT ATRIX LCD INTRODUCTION The is a LCD driver lc which is fabricated by low power COS technology. Basically this lc consists of 40 x 2 bit bi-directional shift register, 40 x 2 bit
More information64CH COMMON DRIVER FOR DOT MATRIX LCD
64 OON DIVE FO DOT ATIX D INTODUTION The (TQFP type: S6B2107) is an D driver SI with 64 channel outputs for dot matrix liquid crystal graphic display systems. This device provides 64 shift registers and
More informationWuxi I-CORE Electronics Co., Ltd. AIP CH SEGMENT DRIVER FOR DOT MATRIX LCD
AIP31063 80CH SEGENT DRIVER FOR DOT ATRIX LCD 1 GENERAL DESCRIPTION The AIP31063 is a LCD driver LSl which is fabricated by low power COS technology. Basically this LSl consists of 40 2 bit bidirectional
More information( DOC No. HX8615A-DS ) HX8615A
( DOC No. HX8615A-DS ) HX8615A Version 05 Mayl, 2005 Version 05 May, 2005 1. General Description The HX8615A is a 240 channel outputs gate driver used for driving the gate electrode of TFT LCD panel. It
More informationMITSUBISI SEMICONDUCTORS <IC> IG OTAGE 3PASE BRIDGE DRIER ABSOUTE MAXIMUM RATINGS Symbol Parameter Conditio Ratings Unit U,, WFB igh Side Floating Sup
MITSUBISI SEMICONDUCTORS IG OTAGE 3PASE BRIDGE DRIER DESCRIPTION is high voltage Power MOSFET and IGBT module driver for 3Phase bridge applicatio. FEATURES FOATING SUPPY OTAGE...6 OUTPUT CURRENT...±3mA
More informationMITSUBISHI SEMICONDUCTORS <HVIC> M63993FP HIGH VOLTAGE 3PHASE BRIDGE DRIVER M63993FP
MITSUBISI SEMICONDUCTORS IG OTAGE 3PASE BRIDGE DRIER DESCRIPTION is high voltage Power MOSFET and IGBT module driver for 3Phase bridge applicatio. FEATURES FOATING SUPPY OTAGE...6 OUTPUT CURRENT...±3mA
More information( DOC No. HX8705-B-DS ) HX8705-B
( DOC No. HX8705-B-DS ) HX8705-B 800x600CH EPD Source+Gate Driver Preliminary version 01 800x600CH EPD Source+Gate Driver Preliminary Version 01 1. General Description The HX8705-B is a 800-channel outputs
More information( DOC No. HX8678-B-DS )
( DOC No. HX8678-B-DS ) Preliminary version 01 1. General Description The HX8678-B is a 480-channel outputs gate driver, which is used for driving the gate line of TFT LCD panel. It is designed for 2-level
More information( DOC No. HX8678-A-DS ) HX8678-A
( DOC No. HX8678-A-DS ) HX8678-A Preliminary version 01 July, 2006 Preliminary Version 01 July, 2006 1. General Description The HX8678-A is a 480/320 channels output gate driver used for driving the gate
More informationCrystalfontz. Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ NT TFT LCD Source Driver V0.6.
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ NT39411 TFT LCD Source Driver V0.6 Preliminary Spec 1 Index INDEX... 2 REVISE HISTORY... 3 FEATURES... 4 GENERAL
More informationSM6781BV Ni-MH/Ni-Cd Battery Charger IC
Ni-MH/Ni-Cd Battery Charger IC OVERVIEW The SM6781BV is a quick charge control IC for Nickel Metal Hydride (NiMH) and Nickel-Cadmium (NiCd) rechargeable batteries. Quick charging ends in response to negative
More informationXC95144 In-System Programmable CPLD. Features. Description. Power Management. December 4, 1998 (Version 4.0) 1 1* Product Specification
查询 XC95144 供应商 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 1 XC95144 In-System Programmable CPLD December 4, 1998 (Version 4.0) 1 1* Product Specification Features 7.5 ns pin-to-pin logic delays on all pins f CNT to 111
More informationXC95288 In-System Programmable CPLD
R 0 XC95288 In-System Programmable CPLD 0 5 Product Specification Features 15 ns pin-to-pin logic delays on all pins f CNT to 95 MHz 288 macrocells with 6,400 usable gates Up to 166 user pins 5V in-system
More informationDESCRIPTION FEATURES APPLICATIONS
DESCRIPTION is a dot matrix LCD driver IC. The bit addressable display data which is sent from a microcomputer is stored in a build-in display data RAM and generates the LCD signal. The incorporates innovative
More informationTS1SSG S (TS16MSS64V6G)
Description The TS1SSG10005-7S (TS16MSS64V6G) is a 16M bit x 64 Synchronous Dynamic RAM high-density memory module. The TS1SSG10005-7S (TS16MSS64V6G) consists of 4 piece of CMOS 16Mx16bits Synchronous
More informationREV. 1.3 FS DS-13_EN MAY FORTUNE' Properties. Datasheet FS For wide range thermal measurement application. For Reference Only
REV. 1.3 FS9168-017-DS-13_EN MAY 2014 Datasheet FS9168-017 For wide range thermal measurement application Fortune Semiconductor Corporation 富晶電子股份有限公司 23F., No.29-5,Sec. 2, Zhongzheng E. Rd., Danshui Dist.,
More informationXC95108 In-System Programmable CPLD
PODUCT OBSOLETE / UNDE OBSOLESCENCE 0 XC95108 In-System Programmable CPLD DS066 (v5.0) May 17, 2013 0 5 Features 7.5 ns pin-to-pin logic delays on all pins f CNT to 125 MHz 108 macrocells with 2,400 usable
More information3Phase spindle motor driver for CD-RW
otor driver ICs BD6670F 3Phase spindle motor driver for CD-RW BD6670F BD6670F is a 3-phase spindle motor driver adopting 180 PW direct driving system. Noise occurred from the motor driver when the disc
More informationAdvantage Memory Corporation reserves the right to change products and specifications without notice
SDRAM SODIMM 4MX64 SDRAM SO DIMM based on 4MX16, 4Banks, 4K Refresh, 3.3V DRAMs with SPD GENERAL DESCRIPTION The Advantage is a 4MX64 Synchronous Dynamic RAM high density memory module. The Advantage consists
More informationAdvantage Memory Corporation reserves the right to change products and specifications without notice
SDRAM DIMM 32MX72 SDRAM DIMM with PLL & Register based on 32MX4, 4 Internal Banks, 4K Refresh, 3.3V DRAMs with SPD GENERAL DESCRIPTION The Advantage is a 32MX72 Synchronous Dynamic RAM high density memory
More informationAdvantage Memory Corporation reserves the right to change products and specifications without notice
SD872-8X8-72VS4 SDRAM DIMM 8MX72 SDRAM DIMM with ECC based on 8MX8, 4B, 4K Refresh, 3.3V DRAMs with SPD GENERAL DESCRIPTION The Advantage SD872-8X8-72VS4 is a 8MX72 Synchronous Dynamic RAM high-density
More informationDS2714. Quad Loose Cell NiMH Charger
DS2714 Quad Loose Cell NiMH Charger www.maxim-ic.com GENERAL DESCRIPTION The DS2714 is ideal for standalone charging of 1 to 4 AA or AAA NiMH loose cells. NiCd cells can also be charged. Temperature, voltage
More informationNC7SV08 TinyLogic ULP-A 2-Input AND Gate
NC7S08 TinyLogic ULP-A 2-Input AND Gate Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Extremely High Speed t PD - 1.0 ns: Typical for 2.7 to 3.6 CC - 1.2 ns:
More informationDS1230Y/AB 256k Nonvolatile SRAM
www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power loss Replaces 32k x 8 volatile static RAM, EEPROM or Flash memory
More informationSYNCHRONOUS DRAM. 256Mb: x4, x8, x16 SDRAM 3.3V
SYNCHRONOUS DRAM 256Mb: x4, x8, x16 Features: Intel PC133 (3-3-3) compatible Fully synchronous; all signals registered on positive edge of system clock Internal pipelined operation; column address can
More informationNC7SV126 TinyLogic ULP-A Buffer with Three-State Output
NC7S126 TinyLogic ULP-A Buffer with Three-State Output Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/O s at CC from 0.9 to 3.6 Extremely High Speed tpd - 1.0 ns: Typical for 2.7 to
More informationNC7SP17 TinyLogic ULP Single Buffer with Schmitt Trigger Input
NC7SP17 TinyLogic ULP Single Buffer with Schmitt Trigger Input Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Propagation Delay (t PD ): 4.0ns Typical for 3.0
More informationRevision History Revision 1.0 (August, 2003) - First release. Revision 1.1 (February, 2004) -Corrected typo.
stacked 1Gb B-die SDRAM Specification Revision 1.1 February 2004 * Samsung Electronics reserves the right to change products or specification without notice. Revision History Revision 1.0 (August, 2003)
More informationDS1250Y/AB 4096k Nonvolatile SRAM
19-5647; Rev 12/10 www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power loss Replaces 512k x 8 volatile static RAM, EEPROM
More informationTO-220. Symbol Description Max Units VIN Input Voltage 15 V IOUT DC Output Current PD/(VIN-VO) ma. -40 to 125 (* in case of IL
TECHNICAL DATA 1.0A Low Dropout Positive Voltage Regulator IL1117-xx The IL1117 is a series of low dropout voltage regulators which can provide up to 1A of output current. The IL1117 is available in eight
More informationIS42S Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM FEATURES OVERVIEW. PIN CONFIGURATIONS 54-Pin TSOP (Type II)
1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM JANUARY 2008 FEATURES Clock frequency: 166, 143 MHz Fully synchronous; all signals referenced to a positive clock edge Internal bank for
More informationLM3621 Single Cell Lithium-Ion Battery Charger Controller
Single Cell Lithium-Ion Battery Charger Controller General Description The is a full function constant voltage, constant current (CVCC) lithium-ion (Li+) battery charger controller. It provides 1% regulation
More informationDS1250W 3.3V 4096k Nonvolatile SRAM
19-5648; Rev 12/10 3.3V 4096k Nonvolatile SRAM www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power loss Replaces 512k
More informationCHARGE CONTROLLER C C S B 2
CHARGE CONTROLLER C C S 9 3 1 0 B 2 D a t a s h e e t Applications for the Computer-Charging-System: Alarm Systems, Cellular Phones, Computer, Electric Vehicles, HiFi, Hobby, Instruments, Lamps, Medical
More informationt WR = 2 CLK A2 Notes:
SDR SDRAM MT48LC16M4A2 4 Meg x 4 x 4 Banks MT48LC8M8A2 2 Meg x 8 x 4 Banks MT48LC4M16A2 1 Meg x 16 x 4 Banks 64Mb: x4, x8, x16 SDRAM Features Features PC100- and PC133-compliant Fully synchronous; all
More informationSDR SDRAM. MT48LC8M8A2 2 Meg x 8 x 4 Banks MT48LC4M16A2 1 Meg x 16 x 4 Banks. Features. 64Mb: x8, x16 SDRAM. Features
SDR SDRAM MT48LC8M8A2 2 Meg x 8 x 4 Banks MT48LC4M16A2 1 Meg x 16 x 4 Banks 64Mb: x8, x16 SDRAM Features Features PC100- and PC133-compliant Fully synchronous; all signals registered on positive edge of
More informationNC7SV126 TinyLogic ULP-A Buffer with Three-State Output
NC7S126 TinyLogic ULP-A Buffer with Three-State Output Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/O s at CC from 0.9 to 3.6 Extremely High Speed tpd - 1.0ns: Typical for 2.7 to
More informationAdvanced Power Electronics Corp.
300mA Low Dropout Linear Regulator with Shutdown Description The is a low dropout, positive linear regu lator with very low quiescent current. The can supply 300mA output current with low dropout voltage
More informationSRS WOW AUDIO PROCESSOR
SS WOW AUDIO POCESSO GENEA DESCIPTION The NJM2700 is a SS WOW audio processor, based on the technology of SS abs, Inc. The NJM2700 reproduces wide and clear sound. In addition, it provides rich bass sound.
More informationA Time-to-Digital Converter with Small Circuitry
Gunma University Kobayashi AB1 ASP-DAC 2009 University SI Design Contest 1D-10 A Time-to-Digital Converter with Small Circuitry Kazuya Shimizu, Masato Kaneta, Shigeyuki Nishimura, aijun in, aruo Kobayashi,
More informationNotes: Clock Frequency (MHz) Target t RCD- t RP-CL t RCD (ns) t RP (ns) CL (ns) A
SDR SDRAM MT48LC4M32B2 1 Meg x 32 x 4 s 128Mb: x32 SDRAM Features Features PC100-compliant Fully synchronous; all signals registered on positive edge of system clock Internal pipelined operation; column
More informationNanoPower P31u / P31uX Datasheet Electric Power System for mission critical space applications with limited resources
NanoPower P31u / P31uX Datasheet Electric Power System for mission critical space applications with limited resources 1 Table of Contents 1 TABLE OF CONTENTS... 2 2 OVERVIEW... 3 2.1 HIGHLIGHTED FEATURES...
More informationNotes: Clock Frequency (MHz) Target t RCD- t RP-CL t RCD (ns) t RP (ns) CL (ns) -6A
SDR SDRAM MT48LC4M32B2 1 Meg x 32 x 4 s 128Mb: x32 SDRAM Features Features PC100-compliant Fully synchronous; all signals registered on positive edge of system clock Internal pipelined operation; column
More informationST x544 System-On-Chip Driver for 480RGBx272 TFT LCD. Datasheet. Version /06
720x544 System-On-Chip Driver for 480RGBx272 TFT LCD Datasheet Sitronix reserves the right to change the contents in this document without prior notice, please contact Sitronix to obtain the latest version
More informationIL1117C-xxLow Dropout Positive Voltage Regulator TECHNICAL DATA
IL1117C-xxLow Dropout Positive Voltage Regulator TECHNICAL DATA Description The IL1117C is a series of low dropout voltage regulators which can provide up to 1A of output current. The IL1117C is available
More informationDTM68102D. 16GB Pin 2Rx4 Registered ECC DDR4 DIMM. DTM68102D 2Gx72 16G 2Rx4 PC4-2133P-RBP-10
Features 288-pin JEDEC-compliant DIMM, 133.35 mm wide by 31.25 mm high Operating Voltage: VDD/VDDQ = 1.2V (1.14V to 1.26V) VPP = 2.5V (2.375V to 2.75V) VDDSPD = 2.25V to 2.75V I/O Type: 1.2 V signaling
More informationLithium Ion Battery Charger for Solar-Powered Systems
Lithium Ion Battery Charger for Solar-Powered Systems General Description: The is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries.
More informationCHARGE CONTROLLER C C S S L. D a t a s h e e t
CHARGE CONTROLLER C C S 9 6 2 0 S L D a t a s h e e t Applications for the CCS-System: Alarm Systems, Cellular Phones, Computer, Electric Vehicles, HiFi, Hobby, Instruments, Lamps, Medical Electronics,
More informationDQ18 DQ19 VDD DQ20 NC *VREF **CKE1 VSS DQ21 DQ22 DQ23 VSS DQ24 DQ25 DQ26 DQ27 VDD DQ28 DQ29 DQ30 DQ31 VSS **CLK2 NC NC SDA SCL VDD
PIN CONFIGURATIONS (Front side/back side) Pin Front Pin Front Pin Front Pin Back Pin Back Pin Back 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 DQ8 DQ9 0 1 2 3 4 5 CB0 CB1 WE 0
More informationMILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS, ANALOG SWITCH WITH DRIVER, MONOLITHIC SILICON
INCH-POUND 4 February 2004 SUPERSEDING MIL-M-38510/116 16 April 1980 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS, ANALOG SWITCH WITH DRIVER, MONOLITHIC SILICON This specification is approved for
More informationDS1643/DS1643P Nonvolatile Timekeeping RAM
Nonvolatile Timekeeping RAM www.dalsemi.com FEATURES Integrated NV SRAM, real time clock, crystal, power-fail control circuit and lithium energy source Clock registers are accessed identically to the static
More informationUSD ,4A 42Vdc Bipolar Driver
2,4A 42Vdc Bipolar Driver Resolution selection between full and half step mode Change resolution on the fly Logic signal TTL/CMOS compatible Current up to 2.4A per phase Chopper frequency over 22KHz Wide
More informationNotes: Clock Frequency (MHz) Target t RCD- t RP-CL t RCD (ns) t RP (ns) CL (ns) -6A E
SDR SDRAM MT48LC32M4A2 8 Meg x 4 x 4 Banks MT48LC16M8A2 4 Meg x 8 x 4 Banks MT48LC8M16A2 2 Meg x 16 x 4 Banks 128Mb: x4, x8, x16 SDRAM Features Features PC100- and PC133-compliant Fully synchronous; all
More informationSDRAM Unbuffered SODIMM. 144pin Unbuffered SODIMM based on 256Mb H-die. 54 TSOP-II/sTSOP II with Pb-Free. (RoHS compliant)
Unbuffered SODIMM 144pin Unbuffered SODIMM based on 256Mb H-die 54 TSOP-II/sTSOP II with Pb-Free (RoHS compliant) INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS, AND IS SUBJECT
More informationACE4108 Max.2A Li-ion Switching Charger IC
Description The ACE4108 is a 2A Li-Ion battery switching charger intended for 12V. Low power dissipation, an internal MOSFET and its compact package with minimum external components requirement makes the
More informationAdvanced Lithium-Ion Linear Battery Charger
Advanced Lithium-Ion Linear Battery Charger General Description is a single Lithium-Ion or Lithium-Polymer cell linear battery charger which is designed for compact and cost-sensitive handheld devices.
More informationSPHV-C Series 200W Discrete Bidirectional TVS Diode
SPHV-C Series W Discrete Bidirectional TVS Diode RoHS Pb GREEN Description The SPHV-C series is designed to replace multilayer varistors (MLVs) in portable applications, LED lighting modules, and low speed
More information256Mbit SDRAM. 8M x 8bit x 4 Banks Synchronous DRAM LVTTL. Revision 0.1 Sept. 2001
256Mbit SDRAM 8M x 8bit x 4 Banks Synchronous DRAM LVTTL Revision 0.1 Sept. 2001 * Samsung Electronics reserves the right to change products or specification without notice. Revision History Revision 0.0
More informationA4004 BATTERY MANAGEMENT ONE CELL LITHIUM-ION/POLYMER BATTERY PROTECTION IC
DESCRIPTION The series product is a high integration solution for lithium-ion/polymer battery protection. contains advanced power MOSFET, high-accuracy voltage detection circuits and delay circuits. is
More informationLow Power, Low Dropout, 250mA, RF - Linear Regulators
Preliminary Datasheet GENERAL DESCRIPTION The series low-power, low-noise, low-dropout, CMOS linear voltage regulators operate from a 2.5V to 5.5V input and deliver up to 25mA. They are the perfect choice
More information2M 4 BANKS 16 BITS SDRAM
2M 4 BANKS 16 BITS SDRAM Table of Contents- 1. GENERAL DESCRIPTION... 3 2. FEATURES... 3 3. AVAILABLE PART NUMBER... 3 4. BALL CONFIGURATION... 4 5. BALL DESCRIPTION... 5 6. BLOCK DIAGRAM... 6 7. FUNCTIONAL
More informationSYNCHRONOUS DRAM. 128Mb: x32 SDRAM. MT48LC4M32B2-1 Meg x 32 x 4 banks
SYNCHRONOUS DRAM 128Mb: x32 MT48LC4M32B2-1 Meg x 32 x 4 banks For the latest data sheet, please refer to the Micron Web site: www.micron.com/sdramds FEATURES PC100 functionality Fully synchronous; all
More information512K 4 BANKS 32BITS SDRAM
512K 4 BANKS 32BITS SDRAM Table of Contents- 1. GENERAL DESCRIPTION... 3 2. FEATURES... 3 3. ORDER INFORMATION... 3 4. BALL CONFIGURATION... 4 5. BALL DESCRIPTION... 5 6. BLOCK DIAGRAM... 6 7. FUNCTIONAL
More informationSDR SDRAM. MT48LC2M32B2 512K x 32 x 4 Banks. Features. 64Mb: x32 SDRAM. Features
SDR SDRAM MT48LC2M32B2 512K x 32 x 4 Banks Features Features PC100-compliant Fully synchronous; all signals registered on positive edge of system clock Internal pipelined operation; column address can
More informationSelf-Adjusting Two-Wire Hall Effect Gear Tooth Sensor IC CYGTS9804
Self-Adjusting Two-Wire Hall Effect Gear Tooth Sensor IC CYGTS9804 The CYGTS9804 is a sophisticated IC featuring an on-chip 12-bit A/D Converter and logic that acts as a digital sample and hold circuit.
More informationMobile Low-Power SDR SDRAM
Mobile Low-Power SDR SDRAM MT48H8M6LF 2 Meg x 6 x 4 banks MT48H4M32LF Meg x 32 x 4 banks 28Mb: 8 Meg x 6, 4 Meg x 32 Mobile SDRAM Features Features V DD /V D =.7.95V Fully synchronous; all signals registered
More informationDTM68116D 32GB Pin 2Rx4 Registered ECC DDR4 DIMM
Features 288-pin JEDEC-compliant DIMM, 133.35 mm wide by 31.25 mm high Operating Voltage: VDD/VDDQ = 1.2V (1.14V to 1.26V) VPP = 2.5V (2.375V to 2.75V) VDDSPD = 2.25V to 2.75V I/O Type: 1.2 V signaling
More information1M 4 BANKS 16 BITS SDRAM
1M 4 BANKS 16 BITS SDRAM Table of Contents- 1. GENERAL DESCRIPTION... 3 2. FEATURES... 3 3. ORDER INFORMATION... 3 4. BALL CONFIGURATION... 4 5. BALL DESCRIPTION... 5 6. BLOCK DIAGRAM... 6 7. FUNCTIONAL
More information512K 4 BANKS 32BITS SDRAM
512K 4 BANKS 32BITS SDRAM Table of Contents- 1. GENERAL DESCRIPTION... 3 2. FEATURES... 3 3. AVAILABLE PART NUMBER... 3 4. PIN CONFIGURATION...4 5. PIN DESCRIPTION... 5 6. BLOCK DIAGRAM... 6 7. FUNCTIONAL
More informationStandalone Linear Li-Ion Battery Charger with Thermal Regulation
HM4056 Standalone Linear Li-Ion Battery Charger with Thermal Regulation FEATURES DESCRIPTION Programmable Charge Current up to 1A No MOSFET, Sense Resistor or Blocking Diode Required Constant-Current/Constant-Voltage
More informationUNISONIC TECHNOLOGIES CO., LTD UC5301
UNISONIC TECHNOLOGIES CO., LTD UC5301 SWITCHED-CAPACITOR VOLTAGE INVERTERS DESCRIPTION The UTC UC5301 is an unregulated charge-pump voltage inverter. It can be used to generate a negative supply from positive
More information400W, 5V - 188V Surface Mount Transient Voltage Suppressor
400W, 5V - 188V Surface Mount Transient Voltage Suppressor FEATURES Low profile package Ideal for automated placement Glass passivated junction Excellent clamping capability Fast response time: Typically
More informationA79L05~A79L24. AiT Semiconductor Inc. ORDERING INFORMATION
THREE TERMINAL NEGATIE OLTAGE REGULATOR DESCRIPTION Three-terminal negative voltage regulator. The is available in SOT89-3 Package. FEATURES main purposes the role of regulator and protection for a variety
More informationAQHV Series 200W Discrete Unidirectional TVS Diode
AQHV Series W Discrete Unidirectional TVS Diode RoHS Pb GREEN Description The AQHV series is designed to provide an option for very fast acting, high performance over-voltage protection devices. Ideally
More informationAg Features. Multi-Stage Charging. Solar Panel or DC Input. Maximum Power Point Tracking (MPPT) Very Low Power Consumption
Datasheet Ag103 Intelligent Sealed Lead Acid Solar Battery Charger Module Pb 1 Features Multi-Stage Charging Solar Panel or DC Input Maximum Power Point Tracking (MPPT) Very Low Power Consumption Wide
More informationGM1117 GM1117V1.01. Features. Description. Application. Typical Application Circuits 1A LOW DROPOUT PRECISION VOLTAGE REGULATOR
Description The is a positive low dropout regulator and is available in an adjustable version and fixed output voltage from 1.5V to 5.0V. All internal circuitry is designed to operate down to 800mV input
More information54ACxxxx, 54ACTxxxx. Rad-hard advanced high-speed 5 V CMOS logic series. Features. Description
Rad-hard advanced high-speed 5 V CMOS logic series Features Data brief Flat-14 Flat-16 Flat-20 DIL-14 DIL-16 DIL-20 AC: 2 to 6 V operating voltage ACT: 4.5 to 5.5 V operating voltage High speed T PD =
More informationSM24CANB Series 500W TVS Diode Array
SM4CANB Series 5W TVS Diode Array RoHS Pb GREEN Description The SM4CANB TVS Diode Array is designed to protect automotive Controller Area Network (CAN lines from damage due to electrostatic discharge (ESD,
More informationSDR SDRAM. MT48LC16M4A2 4 Meg x 4 x 4 Banks MT48LC8M8A2 2 Meg x 8 x 4 Banks MT48LC4M16A2 1 Meg x 16 x 4 Banks. Features. 64Mb: x4, x8, x16 SDRAM
SDR SDRAM MT48LC16M4A2 4 Meg x 4 x 4 Banks MT48LC8M8A2 2 Meg x 8 x 4 Banks MT48LC4M16A2 1 Meg x 16 x 4 Banks 64Mb: x4, x8, x16 SDRAM Features Features PC100- and PC133-compliant Fully synchronous; all
More informationDS1743/DS1743P Y2K-Compliant, Nonvolatile Timekeeping RAMs
DS1743/DS1743P Y2K-Compliant, Nonvolatile Timekeeping RAMs FEATURES Integrated NV SRAM, Real-Time Clock, Crystal, Power-Fail Control Circuit, and Lithium Energy Source Clock Registers are Accessed Identically
More informationA4063. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION TYPICAL APPLICATION
DESCRIPTION The is a 2A Li-Ion battery switching charger intended for 5V adapters. Low power dissipation, an internal MOSFET and its compact package with minimum external components requirement makes the
More informationShrink-TSOP. M464S3323CN0 SDRAM SODIMM 32Mx64 SDRAM SODIMM based on stsop2 16Mx8, 4Banks, 4K Refresh, 3.3V SDRAMs with SPD. Pin. Front. Pin.
M464S3323CN0 SDRAM SODIMM 32Mx64 SDRAM SODIMM based on stsop2 16Mx8, 4Banks, 4K Refresh, 3.3V SDRAMs with SPD GENERAL DESCRIPTION The Samsung M464S3323CN0 is a 32M bit x 64 Synchronous Dynamic RAM high
More informationMA-4025 Solar Charger Patent pending
Features Portable Fast-Charge Solar Battery Charger Maximum Power Point Tracking Up to 30% more power No User Input Required Fully Ruggedized Design Over Temperature Protection Wide-Range DC Input Capable
More informationTC59SM816/08/04BFT/BFTL-70,-75,-80
TENTATIVE TOSHIBA MOS DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC 4,194,304-WORDS 4 BANKS 16-BITS SYHRONOUS DYNAMIC RAM 8,388,608-WORDS 4 BANKS 8-BITS SYHRONOUS DYNAMIC RAM 16,777,216-WORDS 4 BANKS 4-BITS
More informationDS1321 Flexible Nonvolatile Controller with Lithium Battery Monitor
19-6312; Rev 6/12 Flexible Nonvolatile Controller with Lithium Battery Monitor FEATURES Converts CMOS SRAM into nonvolatile memory Unconditionally write-protects SRAM when V CC is out of tolerance Automatically
More informationAttention! Parameter numbers have been changed!
Attention! Parameter numbers have been changed! STEPPING OTOR CONTROL 20A570 20A570 KL2359 INSTRUCTION ANUAL No. 402277 English FRANKL & KIRCHNER EFKA OF AERICA INC. EFKA ELECTRONIC OTORS GBH & CO KG SINGAPORE
More informationDS1245Y/AB 1024k Nonvolatile SRAM
www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power loss Replaces 128k x 8 volatile static RAM, EEPROM or Flash memory
More information512K 4 BANKS 32BITS SDRAM
Table of Contents- 512K 4 BANKS 32BITS SDRAM 1. GENERAL DESCRIPTION... 3 2. FEATURES... 3 3. ORDER INFORMATION... 3 4. PIN CONFIGURATION... 4 5. PIN DESCRIPTION... 5 6. BLOCK DIAGRAM... 6 7. FUNCTIONAL
More informationOIS21C. Optical smart sensor for hydraulic cylinders. General Description. Features. Applications. Pin Functions. Ordering Information
Optical smart sensor for hydraulic cylinders General Description OIS21C is a patented smart optical device, which is usually combined with a hydraulic steering cylinder. The main application is on rough
More informationM464S1724CT1 SDRAM SODIMM 16Mx64 SDRAM SODIMM based on 8Mx16,4Banks,4K Refresh,3.3V Synchronous DRAMs with SPD. Pin. Pin. Back. Front DQ53 DQ54 DQ55
M464S1724CT1 SDRAM SODIMM 16Mx64 SDRAM SODIMM based on 8Mx16,4Banks,4K Refresh,3.3V Synchronous DRAMs with SPD GENERAL DESCRIPTION The Samsung M464S1724CT1 is a 16M bit x 64 Synchronous Dynamic RAM high
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationNC7SVL08 TinyLogic Low-I CCT Two-Input AND Gate
NC7SL08 TinyLogic Low-I CCT Two-Input ND Gate Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Power-Off High-Impedance Inputs and Outputs Proprietary Quiet Series
More information1M 4 BANKS 16 BITS SDRAM
1M 4 BANKS 16 BITS SDRAM Table of Contents- 1. GENERAL DESCRIPTION... 3 2. FEATURES... 3 3. AVAILABLE PART NUMBER... 4 4. PIN CONFIGURATION...4 5. PIN DESCRIPTION... 5 6. BLOCK DIAGRAM... 6 7. FUNCTIONAL
More informationCHARGE SOURCE/LOAD GROUND
DS2715 NiMH Battery Pack Charge Controller www.maxim-ic.com DESCRIPTION The DS2715 is well suited for cost-sensitive charger applications where the battery pack is either internal or external to the application.
More informationRevision History. REV. 0.1 June Revision 0.0 (May, 1999) PC133 first published.
Revision History Revision 0.0 (May, 1999) PC133 first published. Revision 0.1 (June, 1999) - Changed PCB Dimensions in PACKAGE DIMENSIONS This datasheet has been downloaded from http://www.digchip.com
More informationLV8804FV. Fan Motor Driver. Overview The LV8804FV is a motor driver for PC and server fans. Feature Direct PWM 3-phase sensorless motor driver
Ordering number : ENA1441C LV8804FV Bi-CMOS LSI PC and Server Fan Motor Driver http://onsemi.com Overview The LV8804FV is a motor driver for PC and server fans. Feature Direct PWM 3-phase sensorless motor
More informationUni- and Bipolar Hall IC Switches for Magnetic Field Applications TLE 4905 L; TLE 4935 L; TLE L; TLE 4945 L; TLE L.
Uni- and ipolar Hall IC Switches for Magnetic Field Applications TLE 495 L; TLE 495 L; TLE 495- L; TLE 4945 L; TLE 4945-L ipolar IC Features Temperature compensated magnetic performance Digital output
More informationElectrical Characteristics of MAX220/222/232A/242/ Rev. G /883B for /883B and SMD page 1 of 5
SCOPE: +5-POWERED MULTI-CHANNEL RS-232 DRIERS/RECEIERS Device Type Generic Number Pkg Code 01 MAX220(x)/883B J16 & L20 02 MAX222(x)/883B J18 & L20 03 MAX232A(x)/883B J16 & L20 04 MAX242(x)/883B J18 & L20
More informationIS42S16400J IS45S16400J
1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM JULY 2014 FEATURES Clock frequency: 200, 166, 143, 133 MHz Fully synchronous; all signals referenced to a positive clock edge Internal bank
More informationSilvertel. Ag Features. Multi-Stage Charging. Battery Reversal Protection. Reduced Power Consumption. Wide DC or AC Input Voltage Range
Silvertel V1.1 October 2012 Pb 1 Features Multi-Stage Charging Battery Reversal Protection Reduced Power Consumption Wide DC or AC Input Voltage Range High Efficiency DC-DC Converter Programmable Charge
More information