Mounting Frames. INSTALLATION INSTRUCTIONS Mounting Frames

Size: px

Start display at page:

Download "Mounting Frames. INSTALLATION INSTRUCTIONS Mounting Frames"

Dorthy May
5 years ago
Views:

1 Mounting Frames BW15204 / BW15205 / BW15456 / BW15682 INSTALLATION INSTRUCTIONS Mounting Frames W SEP07 (ENGLISH) 300 and 400 Series Loaders John Deere Welland Works W51655 (05SEP07) COPYRIGHT 2007 DEERE & COMPANY Moline, Illinois All rights reserved A John Deere ILLUSTRUCTION Manual W SEP07

3 Introduction IMPORTANT: Read this instruction thoroughly and familiarize yourself with the tractor before installing mounting frames. NOTE: Go to mst.deere.com for estimated install/setup time. This instruction is for installing mounting frames on Compact Utility Tractors for a 300, 300X, 300CX, 400X or 400CX Loader. BW15204: BW X and 400CX Loaders on 4120, 4320, 4500, 4510, 4520, 4600, 4610, 4700, 4710 and 4720 Open Station Compact Utility Tractors BW15456: 300X and 300CX Loaders on 3120, 3320, 3520 and 3720 Cab Compact Utility Tractors 400X and 400CX Loaders on 4120, 4320, 4520 and 4720 Cab Compact Utility Tractors BW CX Loader on 4105 Tractor 300 Loader on 3203 Open Station Compact Utility Tractor 1 300X and 300CX Loaders on 3120, 3320, 3520, 3720, 4200, 4210, 4300, 4310, 4400 and 4410 Open Station Compact Utility Tractors 1 North America ONLY. OUO6038,000197A 19 13AUG07 1/1 Prepare Tractor for Service CAUTION: Before servicing the tractor or loader, perform the following: 1. Disengage all power. 2. Engage tractor parking brake and/or place transmission in PARK. 3. Shut off tractor engine and remove key. 4. Relieve pressure in hydraulic system. (See tractor Operator s Manual.) 5. Wait until all moving parts have stopped. 6. Let all components cool. E50093 UN 08AUG01 OUMX005, MAR04 1/1 W51655 (05SEP07) 1 Installation Instructions PN=3

Remove Paint Before Welding or Heating Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch.

4 Remove Paint Before Welding or Heating Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch. Remove paint before heating: Remove paint a minimum of 100 mm (4 in.) from area to be affected by heating. If paint cannot be removed, wear an approved respirator before heating or welding. If you sand or grind paint, avoid breathing the dust. Wear an approved respirator. If you use solvent or paint stripper, remove stripper with soap and water before welding. Remove solvent or paint stripper containers and other flammable material from area. Allow fumes to disperse at least 15 minutes before welding or heating. TS220 UN 23AUG88 Do not use a chlorinated solvent in areas where welding will take place. Do all work in an area that is well ventilated to carry toxic fumes and dust away. Dispose of paint and solvent properly. DX,PAINT 19 24JUL02 1/1 W51655 (05SEP07) 2 Installation Instructions PN=4

Install Mounting Frames Open Station Tractor 1.

4500, 4510, 4600, 4610, 4700, 4710, 4120, 4320, 4520 and 4720 Tractors (Right-Hand Side): Remove and discard mounting hardware and spacers

5 Install Mounting Frames Open Station Tractor and 4105 Tractors (Right-Hand Side): Remove and save two cap screws from hydraulic coupler bracket (A). 4500, 4510, 4600, 4610, 4700, 4710, 4120, 4320, 4520 and 4720 Tractors (Right-Hand Side): Remove and discard mounting hardware and spacers from hydraulic coupler bracket (A), if equipped. A Coupler Bracket 3203 Tractor Shown W07747 UN 24JAN06 1 North America ONLY. Continued on next page 4500 Tractor Shown OUO6038,0001A9F W07748 UN 24JAN SEP07 1/3 W51655 (05SEP07) 3 Installation Instructions PN=5

3X20 Series Tractor CAUTION: Approximate weight of each mounting frame is 10 kg (22 lbs).

(Refer to REMOVE PAINT BEFORE WELDING OR HEATING in this Instruction.) IMPORTANT: 400X and 400CX: Notch (E) should face toward front of tractor. 3.

4500, 4510, 4600, 4610, 4700, 4710, 4120, 4320, 4520 and 4720 Tractors (Right-Hand Side): Place hydraulic coupler bracket (D), if equipped, over

Fasten mounting frames using four M16 x 40 cap screws (A). Tighten mounting hardware to specification in sequence shown.

6 3X20 Series Tractor CAUTION: Approximate weight of each mounting frame is 10 kg (22 lbs). W07502 UN 04AUG Tractor W07503 UN 09AUG05 NOTE: Right-Hand side shown. 2. Remove paint from all mounting frame-to-tractor frame contact surfaces. (Refer to REMOVE PAINT BEFORE WELDING OR HEATING in this Instruction.) IMPORTANT: 400X and 400CX: Notch (E) should face toward front of tractor. 3. Position mounting frames (B) with pin (C) angled forward, as shown , 4510, 4600, 4610, 4700, 4710, 4120, 4320, 4520 and 4720 Tractors (Right-Hand Side): Place hydraulic coupler bracket (D), if equipped, over mounting frame as shown Tractor W08895 UN 13AUG07 NOTE: Tightening sequence is the same for all tractors. 5. Fasten mounting frames using four M16 x 40 cap screws (A). Tighten mounting hardware to specification in sequence shown. Specification Mounting Frame Hardware Torque N m (229 lb-ft) Tightening Sequence (4720 Tractor Shown) W07510 UN 08AUG05 A Cap Screw, M16 x 40 (4 used per side) B Mounting Frame (1 each side) C Pin D Coupler Bracket (if equipped) E Notch (400X and 400CX only) Continued on next page OUO6038,0001A9F 19 05SEP07 2/3 W51655 (05SEP07) 4 Installation Instructions PN=6

6. 1 3203 and 4105 Tractors (Right-Hand Side): Install existing cap screws and hydraulic coupler bracket. 7. Paint all exposed surfaces. 1 North America ONLY.

(Refer to REMOVE PAINT BEFORE WELDING OR HEATING in this Instruction.) IMPORTANT: Mounting frame must be positioned with pin (D) angled toward front of tractor.

7 and 4105 Tractors (Right-Hand Side): Install existing cap screws and hydraulic coupler bracket. 7. Paint all exposed surfaces. 1 North America ONLY. OUO6038,0001A9F 19 05SEP07 3/3 Install Mounting Frames Cab Tractor NOTE: 3X20 Series tractor shown. 4X20 Series tractor is similar. 1. Remove paint from all mounting frame-to-tractor frame contact surfaces. (Refer to REMOVE PAINT BEFORE WELDING OR HEATING in this Instruction.) IMPORTANT: Mounting frame must be positioned with pin (D) angled toward front of tractor. Install cap screws and flange nuts (A) with flange nuts facing out. Right-Hand Side Shown W07504 UN 04AUG05 2. Position mounting frame (B) on tractor frame extension (C) with pin (D) angled forward, as shown. Fasten mounting frames using four M16 x 50 cap screws and flange nuts (A), with flange nuts facing out. Tighten mounting hardware to specification in sequence shown. Specification Mounting Frame Hardware Torque N m (229 lb-ft) 3. Paint all exposed surfaces. Tightening Sequence A Cap Screw and Flange Nut, M16 x 50 (4 each per side) B Mounting Frame C Tractor Frame Extension D Pin W07505 UN 09AUG05 OUO6038,0001C8E 19 05SEP07 1/1 W51655 (05SEP07) 5 Installation Instructions PN=7

8 W51655 (05SEP07) 6 Installation Instructions PN=8

JOHN DEERE WORLDWIDE COMMERCIAL & CONSUMER EQUIPMENT DIVISION. Lawn Tractors L100, L110, L120, and L130 TM2026 DECEMBER 2002 TECHNICAL MANUAL

2026 December 2002 JOHN DEERE WORLDWIDE COMMERCIAL & CONSUMER EQUIPMENT DIVISION Lawn Tractors L100, L110, L120, and L130 TM2026 DECEMBER 2002 TECHNICAL MANUAL North American Version Litho in U.S.A. Safety