2406TL LOADER MOUNTING KIT KIOTI TRACTORS

Size: px

Start display at page:

Download "2406TL LOADER MOUNTING KIT KIOTI TRACTORS"

Darlene Perry
5 years ago
Views:

1 ASSMBLY MANUAL Keep With Operator s Manual 2406TL LOADR MOUNTING KIT KIOTI TRACTORS MODL 2WD FWA CK20 CK20HST X X TRACTOR & LOADR GNRAL INFORMATION Mounting kit can be installed using tools ordinarily available, including a hoist capable of lifting and supporting the loader for initial mounting, standard wrenches and a torque wrench, hydraulic oil, and a non-sparking drift and hammer (a shot-filled mallet is recommended). Tractor-supplied hydraulic power is required for loader mounting and operation. Two hydraulic kits options are available for use with this loader: A hose kit for use with existing tractor hydraulic control valves, which includes hoses and couplings to plumb to tractor rear remote valve couplers. This mounting kit is compatible with KIOTI model MM20-60 mid-mounted mower. Also compatible with RHINO or SMC model 65A backhoe. If optional grille guard is to be installed, install it during mid mounting bracket installation, before mounting loader. Refer to instructions provided with grille guard. Check tractor tire pressure. Refer to tractor operator's manual for recommended pressures. With tractor on a firm, level surface, compare tractor rear axle height from left to right, measuring from axle center to ground. Adjust air pressure in rear tires until axle height measures same for both sides. NOT: If rear axle on tractor is not level from side to side, cutting edge on loader bucket or similar loadermounted attachments will not sit flat on ground. When loader mounting is complete, you will need to check front tire clearances and adjust tire track width as necessary. You will also need to verify tractor wheel and axle clearances and adjust steering stops accordingly to provide clearance between front tire and tractor hood and loader on full left and right turn with front axle fully oscillated. Be sure lift cylinders are fully retracted when checking tire clearances. Refer to tractor operator's manual for steering stop adjustment. PRPARING TRACTOR Shut off engine, engage brakes, and remove key during installation. If tractor is equipped with front weights, remove weights. It is not necessary to remove weight bracket. Remove plastic thread protectors from holes on left and right sides of tractor. INSTALLING LFT & RIGHT MIDMOUNTING BRACKTS NOT: Install all attaching hardware loose until mounting kit is completely assembled, to facilitate assembly and proper alignment-unless noted otherwise. Torque all hardware to torques specified in General Torque Specifications table when assembly is complete. NOT: Support mid mounting brackets (1 & 2) when removing from shipping materials. 1. Raise left midmounting bracket (1) with overhead hoist. Align mounting holes with holes in casting on left side of tractor. Attach mounting and spacers (3) to clutch housing casting using 14MM x 55MM cap screws (4) and 9/16 lock washers (6). Attach to front frame using 12MM x 35MM cap screws (5) 1/2 flat washers (8) and 1/2 lock washers.(7) 2. Raise right midmounting bracket (2) with overhead hoist. Allign mounting holes with holes in casting on right side of tractor. Attach mounting and spacer (3) to clutch housing casting using 14MM x 55MM cap screws (4) and 9/16 lock washers (6). Attach to front casting using 12MM x 35MM cap screws (5) 1/2 flat washer (8) and 20MM lock washers (7). 3. Tighten 14MM hardware to 85 ft. lbs. (115 N M) and 12MM hardware to 52 ft. lbs. (70 N M) of torque. F-3984 Page 1 of 6

2 Figure PARTS LIST MOUNTING KIT Item Part No. Description Qty MOUNTING BRACKT, Mid, Left MOUNTING BRACKT, Mid, Right PLAT, Support SCRW, Cap, 14MM-1.50MM x 55MM SCRW, Cap, 12MM-1.25MM x 35MM WASHR, Lock, 9/ WASHR, Lock, 1/ WASHR, Flat, 1/2 8 F-3984 Page 2 of 6

3 MOUNTING LOADR TO TRACTOR (Figures 2, 3, 4, 5, 6, 7 & 8) Figure 2B WARNING: Loader must be supported before removing hardware securing loader to shipping pallet, or loader will tip over. WARNING: To avoid injury during installation of quick attach loader, do not permit bystanders within ten feet of loader. WARNING: To avoid injury during installation of quick attach loader, an overhead hoist must be used for initial mouniing. Parking stands are not operational without bucket or heavy attachment mounted. Bale spear or pallet fork alone do not provide enough weight. 4. Lower loader from vertical shipping position to horizontal, positioning scraps of cardboard on floor under loader to protect loader paint (see figure 2B). 5. Install hydraulic plumbing for loader to tractor using hose kit for mid-mount valve. D H L L M K B M M K Figure 3 L A Figure 2A D C J G D F 6. Secure a hoist strap around loader upper boom arms similar to figure 4. Slowly raise loader with overhead hoist until loader upright will clear tires (see figure 4). 1. Loop chain or sling under each tilt cylinder, around loader outer knee plate and hook to each outer knee plate (see figure 3). Put slight tension on overhead hoist to prevent loader from tipping. 2. Temporarily remove linch pins (B) and hitch pins (A) (see figure 3) and keep with loader for securing loader uprights to mid mounting brackets later. 3. Remove 3/8 lock nuts () and flat washers (D) which fasten loader uprights to pallet and can be found inside uprights near top end. Remove 3/8 lock nuts () which fasten shipping angle brackets (G) to pallet. Remove 5/16 lock nuts (H) from U- bolts (J) to remove shipping angle brackets (G) from loader. Discard shipping brackets and hardware. Raise loader off pallet and remove pallet with bucket (see figure 2A). WARNING: Loader uprights may rotate downward when loader is lifted from pallet. 7. Drive tractor into loader until uprights of loader mounting brackets are within 12 or 18 of loader uprights. Shut off engine. Attach lift cylinder function hoses (color coded green and yellow) to corresponding tractor valve couplers. NOT: It is important to attach lift cylinder hoses (coded with yellow and green bands for loader to function properly. Do not connect boom oil line hoses for tilt cylinder control at this time. Connect these after shipping brackets are removed from attachment pin hubs in instruction 12). 8. Start tractor engine. Retract lift cylinders fully and continue to activate control lever for approximately 10 seconds. Cycle cylinders several times to remove air. xtend lift cylinders four or five inches from the fully closed position to ensure loader upright pin will be first part of loader upright to make contact with stop surface of loader mounting brackets. Shut off engine and set brakes and remove key. F-3984 Page 3 of 6

4 Figure 4 Figure 6 9. With overhead hoist, position loader upright pin to clear mount pin saddle by 1 (see figure 5). Start tractor engine and move tractor forward until both loader upright pins come to rest against flat vertical stop surface of both mounting brackets. Shut off engine and set brakes and remove key. 10. Lower loader with overhead hoist until both loader upright pins rest into mount pin saddles. Start tractor engine and retract lift cylinders, rotating loader uprights until uprights are fully seated into back of mount tube saddles (see figure 6). 11. Shut off tractor engine and set parking brakes. Insert two 1 x 4-7/8 pins (A) and linch pins (B), which were removed from loader uprights in instruction 2. Remove hoist chain or strap from loader boom arms.(figure 7) 13. Attach tilt cylinder function hoses (color coded blue and red) to corresponding tractor valve couplers. 14. Start engine and fully extend and retract cylinders several times to purge air from hydraulic system. Add additional tractor hydraulic fluid as specified in tractor operator s manual to bring level of hydraulic fluid up to full. Linch pin Figure 7 Figure 5 mount tube saddle stop surface mount pin saddle 1" loader upright pin Hitch pin NOT: In some cases a small amount of additional force may be required to insert pins. If necessary, use a drift and hammer made of non-sparking material (a shot-filled mallet is recommended) to seat loader uprights into mount tube saddles. 12. Remove 3/8 cap screws (L) and lock nuts () to temporarily remove anti-rotation pins (M) to remove shipping brackets (K) (See Figure 3). Discard shipping brackets (K), retaining anti-rotation pins and hardware for later reuse when installing bucket or attachment. 15. Adjust front wheel tread setting or steering stops, if necessary, to provide a minimum 3/4 clearance between front tires and any part of loader with lift cylinders fully retracted and front axle fully oscillated. Be sure lift cylinder are fully retracted. Refer to page 1, under preparing tractor. Refer to tractor operator s manual for tread setting and steering stop adjustment procedures. F-3984 Page 4 of 6

5 INSTALLING BUCKT OR ATTACHMNT Refer to loader operator's manual to install bucket or optional attachments. WARNING: Always have a bucket attachment mounted to loader when it is removed from tractor. Pallet fork, bale spear or similar attachments are too light to safely counterbalance loader boom arms when loader is dismounted from tractor. To adjust level indicator properly, locate tractor and loader attachment on a firm level surface with attachment resting on level surface in operating position. Loosen U-bolt that fastens level indicator bracket to right tilt cylinder and position it so it is centered on the offset in level indicator rod, then retighten U-bolt hardware. Figure 8 tightener band ATTACH LVL INDICATOR FOR BUCKT OR ATTACHMNT (Figure 8) Refer to assembly instructions provided with bucket or optional attachments to aitach level indicator rod. NOT: Attachment level setting varies for each loader attachment. It is important to make sure level indicaior is adjusted to indicate level whenever a different attachment is mounted, or else level indicator will not indicate true level. level guide tube level indicator rod F-3984 Page 5 of 6

6 GNRAL TORQU SPCIFICATIONS US TH FOLLOWING TORQUS WHN SPCIAL TORQUS AR NOT GIVN Standard American and Metric Cap Screws AMRICAN STANDARD CAP SCRWS MTRIC CAP SCRWS SA Grade 5 8 Metric Class Typ. Head Typ. Head Markings Markings Cap Screw TORQU TORQU Cap Screw TORQU TORQU Size FT LBS N m FT LBS N m Size FT LBS N m FT LBS N m Inches MIN MAX MIN MAX MIN MAX MIN MAX Millimeters MIN MAX MIN MAX MIN MAX MIN MAX 1/ M6 x / M8 x / M10 x / M12 x / M14 x / M16 x / M18 x / M20 x / M22 x / M24 x / M27 x / M30 x / / NOT: These values apply to fasteners as received 3/ from supplier, dry or when lubricated with normal 3/ engine oil. They do not apply if special graphite or 7/ / molysulphide greases or other extreme lubricants are used INSTALLATION INSTRUCTIONS F-3984 Page 6 of 6

LOADER MOUNTING KIT 5211 LOADER JOHN DEERE TRACTORS

ASSEMBLY MANUAL 2-6976 Keep with Operators Manual LOADER MOUNTING KIT 5211 LOADER JOHN DEERE TRACTORS MODEL 2WD FWA ROPS CAB JD 6110, 6120 X X X X JD 6210, 6220 X X X X JD 610, 620 X X X X JD 610, 620