EVG1200W/10A PHplus-R3
|
|
- Domenic Logan
- 5 years ago
- Views:
Transcription
1 PHplus ballasts for optimal lamp operation constant lamp and preheat current even with long cables adjustable operation parameters lamp operation control via RS485 using ModBus or ZCON protocol enhanced protection high efficiency active power factor correction (PFC) (low THD according to EN 61000) metal housing, designed for optimal thermal flow push-in contacts for quick installation easy system setup for standard (local) operation: set all DIP switches to on for parameter defaults optimal preheat settings for soft lamp start (preheat parameters adjustable) lamp and ballast status indication E1200PHplus-R (picture similar) ballast name EVG1200W/10A PHplus-R3 supply voltage: input power: ballast efficiency: operating temperature: ambient temperature: relay contacts: lamp power [W] status LEDs potential free relay contact ModBus/ZCON status request lamp current [A] extra heating current [A] values are to be specified according to lamp type 230V AC ± 10% max. 1200W +8% +500W (depending on extra heating) > 90% max. 50 C (122 F) at TC-point (see 'Ballast marking') 0-40 C ( F) potential free, load: mA at V AC; mA at 5-60V DC Note: The potential free contacts do not provide protection against electric shock. All wires of the error control loop shall be installed with appropriate protection against contact. ballast operation: status indication: IP code: mounting restrictions: connections: dimensions: - standard operation (local mode): lamp operation starts when ballast is connected to mains; set all DIP switches to on for standard parameters; see Ballast Operation Modes for parameter adjustment - remote operation: set parameters and control lamp operation via RS485 using ModBus or ZCON protocol - operating state indicated by LEDs and relay contacts (see wiring diagram) - operating state indicated via RS485 status request using ModBus or ZCON protocol IP20 vertical, mains terminal at bottom side, cable length between ballast and lamp: up to 30m, see Ballast Instructions for details see 'Wiring diagram' see 'Dimensions' 1/5
2 Dimensions Ballast marking 2/5
3 Wiring diagram 3/5
4 Ballast operation local operation lamp operation starts on connecting ballast to mains set all DIP switches to ''on'' for standard parameters use DIP switches 2, 3, 4 for parameter adjustment according to environmental conditions: cold: raise lamp current hot: lower lamp current PH boost: increase preheat time Ballast operation remote operation via RS485 using ZCON control units ballast is in standby on connecting to mains lamp operation is started, controlled and monitored via RS485 by ZCON control unit use DIP switch for communication protocol and ballast ID (see 'DIP switch settings for RS485 remote operation' at page 5) refer to the ZCON control units manual for ballast operation details using PLC with ModBus protocol ballast is in standby on connecting to mains lamp operation is started, controlled and monitored via RS485 by PLC use DIP switch for communication protocol and ballast ID (see 'DIP switch settings for RS485 remote operation' at page 5) ModBus implementation of PLC has to be done by customer details concerning ModBus implementation are available on request 4/5
5 Ballast operation settings remote operation via RS485 default settings: lamp current: (to be specified according to lamp type) preheat current: (to be specified according to lamp type) preheat time: (to be specified according to lamp type) control features specification: device type The default settings for lamp current, preheat current and preheat time are defined according to the data of the lamp manufacturer for standard application. Different settings might be used to adjust the lamp parameters to different environmental conditions. Ask lamp manufacturer for boundary conditions of such adjustments. DIP switch settings for RS485 remote operation When remotely controlled via RS485 each ballast needs an unique identifier. This ballast address or ballast ID is to be assigned using the DIP switches The appropriate communication protocol, either ZCON or ModBus, is selected via DIP switches 1-3 (see example below). communication protocol switch settings switch settings ballast ID ZCON enabled = 20 1 ModBus enabled = 21 2 = Any DIP switch settings have to be performed before connecting ballast to mains. ballast ID (arithmetic examples)... = /5
ENGINEERING FLOW SOLUTIONS PROTECTION & CONTROL PANELS. Control ST series
ENGINEERING FLO SOLTIONS PROTECTION & CONTROL PANELS Control ST series HMS Control ST series Panel for up to pumps APPLICATION The HMS Control ST panels are intended for control and protection of up to
More informationObserve all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.
Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary
More informationHeat Tracing Sales Mt. Airy, Maryland Controls
Heat Tracing Line Sensing Control Panels Solid State Relay Output Rated 30 Amps or Two-Pole Contactor Control Output Universal Inputs NEMA 4/4X Enclosure Ground Fault Alarm/Trip Monitor or GFI Circuit
More informationUnidrive M400 Fast set-up and diagnostics with real-text display, integrated PLC and safety inputs
Unidrive M400 Fast set-up and diagnostics with real-text display, integrated PLC and safety inputs 0.25 kw - 110 kw (0.33 hp - 150 hp) 100 V 200 V 400 V 575 V 690 V Unidrive M400 features Optional AI-485
More informationPOWER SUPPLIES. Control Transformers p8-1 Modular Power Supplies p8-2 Switching Power Supplies p8-3 Automatic Battery Chargers p PAGE
8 POWER SUPPLIES Control Transformers p8-1 Modular Power Supplies p8-2 Switching Power Supplies p8-3 Automatic Battery Chargers p8-10 Perth (08) 9248 0410 Sydney (02) 9676 1671 Melbourne (03) 9706 4599
More informationElectronic ballasts for fluorescent lamps Multi-lamp ECG. PC T5 PRO-M lp, W T5, T8, compact (CFL) and T5c circular fluorescent lamps
T5 T8 TC-F TC-L T5c PC T5 PRO-M lp, 14 80 W T5, T8, compact (CFL) and T5c circular fluorescent lamps Product description Integrated lamp detection Operation of T5 lamps of the same length Average life
More informationET9500 BEMS Interface Box Configuration Guide
ET9500 BEMS Interface Box Configuration Guide APPLICABILITY & EFFECTIVITY Explains how to install and configure ET9500 BEMS Interface Box. The instructions are effective for the above as of August, 2015
More informationINTECH Micro 2300-RTD6
INTECH Micro 2300-RTD6 6 Channel RTD Input Station Overview. The Intech Micro 2300 Series is a system of modular I/O Remote Stations, that add an even lower cost option to Intech s already extensive intelligent
More informationAdvanced Battery Charger 0 ~ 15A 0 ~ 25A 0 ~ 35A 0 ~ 50A 0 ~ 80A. 3 - stage charging capability (IUOU) 90 ~ 264VAC (refer to de-rating curve)
Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.
More information720 W / 24 V On-board Battery Charger. for industrial applications. Product Data Sheet
for industrial applications Product Data Sheet 720 W / 24 V On-board Battery Charger for industrial applications Features IP65 protection degree Battery selection via GUI, supporting all leading battery
More informationSMT-AZC INSTALLATION / OPERATION MANUAL
SMT-AZC INSTALLATION / OPERATION MANUAL 22o OFF VERSION 2.0 www.smarttemp.com INTRODUCTION The SMT-AZC thermostat is designed to work with the Smart Temp 24Volt Zone Dampers TERMINAL DESIGNATIONS The SMT-AZC
More informationInstallation & User Instructions
Installation & User Instructions 16/25A Digital Dimmer (416/425) INTRODUCTION The 416 and 425 are Digital Dimmers capable of dimming a single channel with total loads of up to 16A and 25A respectively.
More informationConnecting Two and Three wire Generator Controllers to the SP PRO
Connecting Two and Three wire Generator Controllers to the SP PRO The SP PRO can be connected by default to both two and three wire generator controllers. Six different schemes are detailed: -Two Wire
More informationAdvanced Battery Charger. 3 - stage charging capability (IUoU) 25A
Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.
More informationWPS20/S EP Series. Features:
Features: Rotate speed governor: Mechanical governor Excitation system: self-excited SHUNT A.V.R model: R220 Emergency stop switch ATS (automatic transfer switch) receptacle 1x12V sealed for life maintenance
More informationFL ballasts Electronic fixed output. PC T5 TOP lp, W PC TOP T5
EL T5 TC-L PC T5 TOP lp, 1 5 W PC TOP T5 Product description CELMA Energy Efficiency Index A2 Nominal life up to 50,000 hours (at ta. 50 C with a failure rate max. 0.2 % per 1,000 hours) Large temperature
More informationWPS60/S EP Series. Features:
Features: Rotate speed governor: Mechanical governor Excitation system: self-excited SHUNT A.V.R model: R220/R438 Emergency stop switch ATS (automatic transfer switch) receptacle 1x12V sealed for life
More informationPresentation Soft starters 0 Altistart 48 soft start - soft stop units
Presentation Soft starters 5 6 7 65_Ver.-EN.fm/ Presentation (continued) Soft starters Applications The Altistart 8 soft start - soft stop unit is a controller with 6 thyristors which is used for the torque-controlled
More informationWPS150/S EP Series. Features:
Features: Rotate speed governor: Mechanical governor Excitation system: self-excited A.V.R model: R250/R438 Emergency stop switch ATS (automatic transfer switch) receptacle 1x12V sealed for life maintenance
More informationWPS100/S EP Series. Features:
Features: Rotate speed governor: Mechanical governor Excitation system: self-excited A.V.R model: R250/R438 Emergency stop switch ATS (automatic transfer switch) receptacle 1x12V sealed for life maintenance
More informationUSERS MANUAL MCD REMOTE OPERATOR
USERS MANUAL MCD REMOTE OPERATOR Order Code: 175G9004, 175G3061 Contents Contents Introduction...2 Important User Information...2 General Description...2 Symbols Used in this Manual...2 Installation...3
More informationLiebert NX8 User Manual +%`K6 UPS
Liebert NX UserManual UPS Liebert NXC 60kVA UPS User Manual Special Declaration Personnel Safety Product Safety Disclaimer Safety Precaution Chapter 11 Specifications ~ 3.1.4 Selection Of UPS I/O Switch
More informationAdvanced Battery Charger. 3 - stage charging capability (IUOU) 4.1 A / 100VAC 1.8A / 240VAC
Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.
More informationWPS350/S EP Series. Features:
Features: Rotate speed governor: Electronic Excitation system: self-excited, SHUNT A.V.R model: R250/R450 Emergency stop switch ATS (automatic transfer switch) receptacle 2x12V sealed for life maintenance
More informationSDOMEO51MV USER MANUAL. Portable Rugged PTZ Cameras
SDOMEO51MV USER MANUAL Portable Rugged PTZ Cameras Table of Contents ABOUT THE PRODUCT... 3 Features... 4 Functions... 5 Technical Data... 8 PREPARATION... 10 Dip Switch... 10 Initial Power On Test...
More informationWPS250/S EP Series. Features:
Features: Rotate speed governor: Electronic Excitation system: self-excited, SHUNT A.V.R model: R250/R450 Emergency stop switch ATS (automatic transfer switch) receptacle 2x12V sealed for life maintenance
More informationElectronic ballasts for fluorescent lamps Professional electronic ballast
HE PC TC PRO 1/2x9 70 W,,, HE,,, compact fluorescent lamps Product description Average life = 50,000 hours (at ta for 50,000 h with a failure rate 0.2 % per 1,000 hours) Large temperature range (for values
More information1/2 thru 1.5 Hp 1/2 thru 3 Hp 2 thru 5 Hp 1 thru 10 Hp
VS1MX AC Micro Drive 1/2 thru 1.5 Hp 1/2 thru 3 Hp 2 thru 5 Hp 1 thru 10 Hp & Controls 115 VAC 230 VAC 230 VAC 460 VAC 1 Phase - 50/60 Hz 1 Phase - 50/60 Hz 3 Phase - 50/60 Hz 3 Phase - 50/60 Hz Applications:
More information1. Product Information
AVS Control Panel 1. Product Information AVS is a pump control panel having 4.3 TFT touch screen, uniquely designed high efficient variable speed control and relay board. The touch control panel is located
More informationMGL Avionics EFIS G2 and iefis
MGL Avionics EFIS G2 and iefis Guide to using the MGL RDAC CAN interface with the LAD AERO Injection Kit on ROTAX 912-912S General... 3 Data connections... 3 LAD AERO ROTAX 912 engine data from ECU...
More informationModel H30 Operation Manual
Model H30 Operation Manual Model H30 Version 1.0 August 1, 2007 2 135 West Davenport Street Rhinelander WI 54501 Phone: 866.441.7997 Fax: 866.278.0036 info@houstonst.com www.houstonst.com 3 Table of Contents
More informationCascade CD101 Auto-Start Controller. Installation and Operations Manual Sections 40 & 75
Cascade CD101 Auto-Start Controller Installation and Operations Manual 00-02-0594 2018-02-15 Sections 40 & 75 In order to consistently bring you the highest quality, full featured products, we reserve
More informationSD1 Series General Purpose AC Variable Speed Drives
1 200/240V 50/60Hz 0.4~2.2kW (0.5~3HP) 3 200/240V 50/60Hz 0.4~7.5kW (0.5~10HP) 3 380/440V 50/60Hz 0.75~110kW (1~150HP) IP20 Torque Vector Control STO (safe torque off) Up to 150% Starting Torque Front
More informationFL ballasts Electronic fixed output. PC TC PRO 1/2x9 70 W PC PRO compact
EL HE PC TC PRO 1/2x9 70 W PC PRO compact Product description CELMA Energy Efficiency Index A2 BAT / A2 Nominal life-time up to 100,000 h (at ta 50 C with a failure rate max. 0.2 % per 1,000 h) Large temperature
More informationPC T8 TEC, W PC TEC
T8 TC-L PC T8 TEC, 18 58 W PC TEC Product description CELMA Energy Efficiency Index A2 Nominal life time up to 30,000 h (at ta 50 C with a failure rate max. 0.3 % per 1,000 h) Large temperature range (for
More information1 EASY COMMISSIONING GUIDE FRONIUS PV-SYSTEM CONTROLLER
1 EASY COMMISSIONING GUIDE FRONIUS PV-SYSTEM CONTROLLER Reading this document does not substitute for user s reference to CIRCUTOR CDP-DUO user-guide. 1.1 Scope Using Fronius grid-tie inverters in remote
More informationFL ballasts Electronic fixed output PC T8 TEC, W PC TEC T8
T8 TC-L PC T8 TEC, 18 58 W PC TEC T8 Product description CELMA Energy Efficiency Index A2 Nominal life time up to 30,000 h (at ta 50 C with a failure rate max. 0.3 % per 1,000 h) Large temperature range
More informationGE FANUC Parts. VersaPoint Power Terminal. Segment Terminal Fused, with Diagnostics 24VDC IC220PWR013. Features. Ordering Information
Segment Terminal Fused, with Diagnostics 24VDC Segment Terminal module is used to create a protected partial circuit (segment circuit) within the main circuit. It is not used to supply power and has no
More informationSuperstatic 440. Static Heat- and Cooling Meter. Application
Superstatic 440 Static Heat- and Cooling Meter Application Design The Superstatic 440 is a static heat- and cooling meter according to standard EN1434 class 2 based on the fluid oscillation principle,
More informationMSR01. Water heating controller with solar panel support
MSR01 Water heating controller with solar panel support version 1.4 trading Czech Republic Czech Republic 1 Content 1. Device description...3 2. Device interface...3 2.1. Inputs...3 2.2. Low tariff...3
More informationD Series: UPS UPTO - 300KVA - Three / Three Phase
D Series: UPS UPTO - 300KVA - Three / Three Phase All in one D Series UPS High Power UPS Systems, Now in India Properties : Standard Properties 1GBT rectifier inverter technology Input power factor correction
More informationUser Manual JS-ICON. 624 ARCH Dimmer Rack. JOHNSON SYSTEMS INC. Spring
User Manual JS-ICON 624 ARCH Dimmer Rack JOHNSON SYSTEMS INC. Spring 2007 2002161 Table of Contents JS-ICON 624 DMX JS-ICON 624 CC 6-2.4kW Dimming Strip JS-ICON 624 ND 6-2.4kW Relay Strip Introduction...3
More informationLiquid Turbine Flow Meter OwnerÊs Manual
Liquid Turbine Flow Meter OwnerÊs Manual Manual LWGY-G Rev.1.0 Content 1.0 GENERAL INFORMATION... 1 2.0 SPECIFICATIONS... 2 3.0 OPERATION CONDITIONS... 3 4.0 CAUTIONS FOR INSTALLATION... 4 5.0 DIMENSION...
More informationWelcome to ABB machinery drives training. This training module will introduce you to the ACS850-04, the ABB machinery drive module.
Welcome to ABB machinery drives training. This training module will introduce you to the ACS850-04, the ABB machinery drive module. 1 Upon the completion of this module, you will be able to describe the
More informationATS22D88Q soft starter-ats22-control 220V-power 230V (22kW)/ V(45kW)
Product datasheet Characteristics ATS22D88Q soft starter-ats22-control 220V-power 230V (22kW)/400...440V(45kW) Complementary Assembly style Function available Supply voltage limits Main Range of product
More informationTHYRO-PX SERIES DIGITAL THYRISTOR SCR POWER CONTROLLER UP TO 2900 AMPS
DIGITAL THYRISTOR SCR POWER CONTROLLER UP TO 2900 AMPS The Thyro-PX series are modular, easy-to-use premier performance SCR power controllers for heating elements, resistive loads and transformer loads,
More informationHeating Cable. Description
ITLS Base Panel Heat Tracing Control Panel for Ordinary Areas 10 VGA Touch Screen HMI 40 Amps/Loop @ 100 600 VAC 6 Loops to 72 Loops NEMA 4 or NEMA 4X Enclosure SCR Control Optional Wireless Temperature
More informationFL ballasts Electronic fixed output. PC TCL PRO, W PC PRO compact
EL T5c T8 TC-L PC TCL PRO, 36 55 W PC PRO compact Product description CELMA Energy Efficiency Index A2 / A3 Nominal life-time up to 50,000 hours (at max. ta with a failure rate max. 0.2 % per 1,000 hours)
More informationXFE. The cost effective starter for all AC induction motors from 4A 2800A The choice for small to medium industrial applications
The cost effective starter for all AC induction motors from 4A 2800A The choice for small to medium industrial applications The XFE Soft Starter range provides a combination of competitive prices, flexible
More informationGMS200C/S EC Series. Features:
Features: Rotate speed governor: Electrical governor S6700E Excitation system: Self excited A.V.R model: AS440 Emergency stop switch ATS (automatic transfer switch) receptacle 2xV sealed for life maintenance
More informationSonoMeter 30 Energy Meters
SonoMeter 30 Energy Meters Description The Danfoss SonoMeter 30 is a range of ultrasonic, compact energy meters intended for measuring energy consumption in heating and cooling applications for billing
More informationGMS100C/S EC Series. Features:
Features: Rotate speed governor: Mechanical governor Excitation system: Self excited A.V.R model: SX440 Emergency stop switch ATS (automatic transfer switch) receptacle 2x12V sealed for life maintenance
More informationFL ballasts Electronic fixed output
PC PRO lp, PC PRO sl, 18 58 W PC PRO Product description Highest possible CELMA Energy Efficiency Index EEI = A2 BAT 21 0 Nominal life up to 100,000 h (at ta. 50 C with a failure rate max. 0.1 % per 1,000
More informationModel TUR-200D Turbine Flowmeter
General Specifications Model TUR-200D Turbine Flowmeter Liquid flows through the turbine housing causing an internal rotor to spin. As the rotor spins, an electrical signal is generated in the pickup coil.
More informationFLÄKTGROUP PM-MOTOR WITH INTEGRATED FC 106 FREQUENCY CONVERTER
FLÄKTGROUP PM-MOTOR WITH INTEGRATED FC 106 FREQUENCY CONVERTER INSTALLATION AND MAINTENANCE INSTRUCTIONS Risk of electric shock: Motor terminals may still be live if the impeller is rotating, even when
More informationFL ballasts Electronic fixed output
T8 PC T8 PRO lp, PC T8 PRO sl, 18 58 W PC PRO T8 Product description Highest possible CELMA Energy Efficiency Index EEI = A2 BAT 21 0 Nominal life up to 100,000 h (at ta. 50 C with a failure rate max.
More informationVLM20 In-line Vortex Flowmeter
ocal regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationSubject Underhood G System Error Codes and Symptoms System or Parts affected
System or Parts affected Index Underhood70G (V90Gxxx) System or Parts affected... 1 Overview... 1 Identifying your System... 1 Retrieving Logged Error Messages... 1 Error Messages... 3 Error Message Table...
More information:34 1/15 Hub-4 / grid parallel - manual
2016-02-24 11:34 1/15 Hub-4 / grid parallel - manual Hub-4 / grid parallel - manual Note: make sure to always update all components to the latest software when making a new installation. Introduction Hub-4
More informationGMS350C/S EC Series. Features:
Features: Rotate speed governor: Electircal governor FP801 Excitation system: Self excited, SHUNT A.V.R model: AS440 Emergency stop switch ATS (automatic transfer switch) receptacle 2x12V sealed for life
More information3ph UPS NS3000 series kVA
3ph UPS UPS NS3000 SERIES NS3000 series 10-120kVA UPS NS3000 SERIES Main concepts in NS3000 design Last Generation 3ph UPS Features Fast and Simplified Intervention Range and Mechanical features NS3000
More informationEmergency lighting units EM INVERTER
T5 T8 TC-DEL TC-SEL TC-TEL TC-L TC-DD EM, 230 240 V 50/60 Hz version Product description Emergency lighting supply unit for manual testing For linear and compact fluorescent lamps Small dimensions (28
More informationSonoMeter 30 Energy Meters
SonoMeter 30 Energy Meters Description MID examination certificate no.: LT-1621-MI004-020 The Danfoss SonoMeter 30 is a range of ultrasonic, compact energy meters intended for measuring energy consumption
More informationAC drive has detected too high a Check loading
Fault code Fault Name Fault type Default Possible Cause Remedy 1 Over Current Fault AC drive has detected too high a Check loading current (>4*IH) in the motor cable: Check motor Sudden heavy load increase
More informationTECHNICAL DATA SHEET INFINITY kva 3Ph(in) 3Ph(out)
TECHNICAL DATA SHEET INFINITY 3300 10 15 20 kva 3Ph(in) 3Ph(out) GENERAL INFORMATION POWER - kva 10 15 20 UPS typology ON LINE Double conversion ACTIVE stand by-operation (Optional) Nominal output power
More informationTWIN FAN CONTROLLER. Models:- ITC and ITC-DS Maximum load : V 50Hz ~ 9A and V 50Hz 3 ~ 9A
TWIN FAN Installation and Wiring Instructions Models:- ITC and ITC-DS Maximum load : 220-240V 50Hz ~ 9A and 380-415V 50Hz 3 ~ 9A IMPORTANT - READ THESE INSTRUCTIONS FULLY BEFORE COMMENCING INSTALLATION.
More information1/2 thru 1.5 Hp 1/2 thru 3 Hp 2 thru 5 Hp 1 thru 10 Hp
VS1MX AC Micro Drive 1/2 thru 1.5 Hp 1/2 thru 3 Hp 2 thru 5 Hp 1 thru 10 Hp & Controls 115 VAC 230 VAC 230 VAC 460 VAC 1 Phase - 50/60 Hz 1 Phase - 50/60 Hz 3 Phase - 50/60 Hz 3 Phase - 50/60 Hz Applications:
More informationADJUSTABLE FREQUENCY CONTROLS SENSORLESS VECTOR CONTROL. Dual Rating. Technologies Inc. mgitech.com NRTL/C CERTIFIED
ADJUSTABLE FREQUENCY CONTROLS SENSORLESS VECTOR CONTROL Dual Rating NRTL/C CERTIFIED Technologies Inc. mgitech.com Sensor/Sensorless Vector Control Dual current rated for constant and variable torque Auto
More informationSoftstarters. Softstarters Type SSM Medium voltage ,800V 1
Medium voltage 2300 13,800V 1 Description Fused disconnect switch with blown fuse indicators and door safety interlocks rated for load break/fault make with automatic grounding arm Inline isolation vacuum
More informationBenefits. transmission devices (gearboxes, pulleys, gears, conveyers, etc) Soft-Star ters are static star ting switches, designed for the
Soft-Starter Benefits Strong reduction on mechanical stresses over the coupling and transmission devices (gearboxes, pulleys, gears, conveyers, etc) Soft-Star ters are static star ting switches, designed
More informationPQube 3 Modbus Interface
PQube 3 Modbus Interface Reference manual Revision 1.9 Modbus Interface Reference Manual 1.9- Page 1 Table of Contents 1. Background... 3 2. Basics... 3 2.1 Registers and Coils... 3 2.2 Address Space...
More informationTHYRISTORS T2-2PH from 45A to 2700A Specifications Universal 2 Phase Thyristor Unit , March 2012
Technical Information THYRISTORS T-PH from 5A to 700A Specifications Universal Phase Thyristor Unit 55-77-03-63, March 0 GENERAL DESCRIPTION THYRISTORS T-PH is a full digital and universal Thyristor unit
More informationML Maximum Power Point Tracking (MPPT) Series ML2420-ML2430-ML2440 Solar Charge and Discharge Controller
ML Maximum Power Point Tracking (MPPT) Series ML2420-ML2430-ML2440 Solar Charge and Discharge Controller Product Features With the advanced dual-peak or multi-peak tracking technology, when the solar panel
More informationSTRA-24 for chilled beams
STRA- Installation and commissioning manual STRA- for chilled beams STRA- is the room controller for the pressure independent (Pi) and constant air volume chilled beams. It is possible to set different
More informationFlash Point Process Analyzer
Norms and standards ASTM D 56 ASTM D 93; DIN EN ISO 2719; IP 34 DIN EN ISO 13736; IP170 DIN 51755 Application The BARTEC BENKE Flash Point Process Analyzer (FPA-4) is a continuously measuring analyzer,
More informationV500UC2 GENERAL CHARACTERISTICS POWER DIMENSIONS COMPACT VERSION DIMENSIONS SOUNDPROOFED VERSION POWER DEFINITION TERMS OF USE.
Engine ref. Alternator ref. Performance class TAD1641GE KH02450T G3 DESCRIPTIVE GENERAL CHARACTERISTICS Frequency (Hz) 60 Hz Voltage (V) 480/277 Standard Control Panel APM403 Optional control panel APM802
More informationICVS-TX MOBILE DUAL IMAGER THERMAL PTZ CAMERA USER MANUAL
ICVS-TX MOBILE DUAL IMAGER THERMAL PTZ CAMERA USER MANUAL ICVS-Tx_CM 3/7/14 V1.2 Safety Notes Thank You for choosing our Mobile Dual Imager Thermal PTZ camera! When you open the box: 1. Check that the
More informationAiM User Guide. MoTec M1. Release 1.00
AiM User Guide MoTec M1 Release 1.00 1 Supported models This user guide explains how to connect MoTec M1 series ECUs to AiM devices. Supported models are: M130 M142 M150 M170 M181 M182 M190 2 Software
More informationCompany name: GSI Created by: Xiao Ying Wong Phone: Date: 10/03/2017 Client: Client Number: Contact:
Position Qty. Description 2 NBG 125-8-16/156 A-F2-A-BAQE Product No.: On request Non-self-priming, single-stage, centrifugal volute pump designed according to ISO 5199 with dimensions and rated performance
More informationLSLV High-Performance Standard Drive 0.4~2.2kW 1-Phase 200~240Volts 0.4~15kW 3-Phase 200~240Volts 0.4~75kW 3-Phase 380~480Volts
www.lsis.com High-Performance tandard Drive 0.4~2.2kW 1-Phase 200~240Volts 0.4~15kW 3-Phase 200~240Volts 0.4~75kW 3-Phase 380~480Volts trong power with a compact size! Powerful sensorless control, and
More informationKH275. Frequency (Hz) Optional control panel POWER. Voltage
KH Engine type P126TI Alternator type KH0T Performance class G3 GENERAL CHARACTERISTICS Frequency (Hz) 50 Voltage (V) 400/230 Standard control panel APM303 APM802 M80 APM403 POWER Voltage ESP PRP Standby
More informationUHP-500 series. 500W Slim Type with PFC Switching Supply
Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 500W Slim Type with PFC Switching Supply S&E GB4943 UL950- EN950- IEC950- % - ~+ Industrial automation machinery Industrial
More information10 20KVA 3Ph/1Ph KVA 3Ph / 3Ph
VEGA INDUSTRIAL UNINTERRUPTIBLE POWER SUPPLY 10 20KVA 3Ph/1Ph 10 120KVA 3Ph / 3Ph - 6 pulse SCR rectifier - IGBT inverter - Power output transformer - Low and stable ripple on battery for the highest battery
More informationJ1000. Compact Inverter Series.
J1000 Compact Inverter Series www.yaskawa.eu.com Focus on Application Customer orientation and application focus two attributes of machine equipment YASKAWA offers with its J1000 compact inverter drive
More informationBBC-3140 USER MANUAL DC-DC CHARGER / BATTERY EQUALIZER / VOLTAGE REDUCER
BBC-3140 USER MANUAL DC-DC CHARGER / BATTERY EQUALIZER / VOLTAGE REDUCER Important The BBC -3140 must be used according to the local safety standards with the particular application. All wiring and connections
More informationOperation Manual. Select/DMX 4Bank
Operation Manual Select/DMX 4Bank Part No. 3100053 Rev A 4-28-2011 System CFX-4804 CFX-2404 4ft 4Bank Fixture 2ft 4Bank Fixture MTP-KL41 Kino 41L Mount w/ 3/8 Pin (10mm) X16-25 4Bank Extension, 25ft BAL-455-120
More informationRS485 MODBUS Card. User Manual. Before you start to install this card, please read this User Manual carefully
Before you start to install this card, please read this User Manual carefully Thanks for choosing MPI Series RS485 MODBUS Card which is a highly reliable product made by with its innovative design and
More informationREGAL-BELOIT SpinMaster AC Adjustable Speed Drives
REGAL-BELOIT SpinMaster Volts/Hertz Constant Torque, Micro Inverter Applications: Constant torque or constant horsepower applications. Typical applications include conveyors, packaging machinery, machine
More informationCommunication module. Brief description. Block structure Features. Page 1/5. Data Sheet
M. K. JUCHHEIM GmbH & Co Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 (0) 661 60 03-7 25 Fax: +49 (0) 661 60 03-6 81 E-Mail: mail@jumo.net
More informationSystem Connection Box. Engine Connection Box. Engine. Legend. VP Wiring. VP Supply. Yard Wiring SEM C. File Name: SEM C
Modbus on RS To yard System Connection Box Marine Control Unit MCU Potential free relay contacts X... X6 Signals from VP system to yard IDCOM Shut Down Unit SDU Terminal Block X9 Signals to VP system from
More informationLogic module. Brief description. Features. Block structure. Data Sheet Page 1/5
M. K. Juchheim GmbH & Co UK USA Jumo Instrument Co. Ltd. Jumo Process Control Inc. 36035 Fulda, Germany Temple Bank, Riverway 735 Fox Chase Phone (0661) 6003-0 Harlow, Essex CM20 2TT Coatesville, PA 19320
More informationINSTALLATION USER MANUAL
INSTALLATION & USER MANUAL DYNAMIC LOAD MANAGEMENT -PREMIUM- This document is copyrighted, 2016 by Circontrol, S.A. All rights are reserved. Circontrol, S.A. reserves the right to make improvements to
More informationMEASURE TODAY. ENSURE TOMORROW. SpireMag Series T-MAG Electromagnetic BTU Meter
MEASURE TODAY. ENSURE TOMORROW. SpireMag Series T-MAG Features The T-MAG BTU meter is the latest addition to the SpireMag series for accurate thermal energy measurement. It utilizes a high accuracy electromagnetic
More informationNumber 1 in efficiency
PowerXL DE1 Variable Speed Starter www.eaton.eu/de1 Number 1 in efficiency The new device category! The PowerXL DE1 Variable Speed Starter The PowerXL DE1 Variable Speed Starter one device, all the advantages
More informationKM2500. Engine type Alternator type Performance class
Engine type Alternator type Performance class S16R2PTAW KH05793T G3 GENERAL CHARACTERISTICS DESCRIPTIVE Kohler Co. Provides onesource responsibility for the generating system and accessories The generator
More information350W Slim Type with PFC Switching Power Supply
Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 350W Slim Type with PFC Switching Power Supply S&E GB4943 UL950-1 EN950-1 EN335-1 IEC950-1 % - ~+ Industrial automation machinery
More informationUnidrive M700 Class leading performance with onboard real-time Ethernet
Unidrive M Class leading performance with onboard real-time Ethernet. kw -.8 MW Heavy Duty (. hp -, hp) V V V 9 V Unidrive M features Easy click-in keypad connection Range of multi-language LCD keypads
More informationUHP-200 series. 200W Slim Type with PFC Switching Power Supply. File Name:UHP-200-SPEC GB4943 EN EN UL IEC
Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 GB494 UL950- EN950- EN5- IEC950- % - ~+ R SPECIFICATION MODEL UHP-00 -. UHP-00-4. UHP-00-5 UHP-00 - UHP-00-5 UHP-00-4 UHP-00-6
More informationDusty / Dusty Ex. Low-Cost Broken Bag Detection. Operating Instructions. SWR engineering Messtechnik GmbH
EN Dusty / Dusty Ex Operating Instructions Low-Cost Broken Bag Detection SWR engineering Messtechnik GmbH CONTENTS Page 1. Introduction.............................................................. 3 1.1
More informationCLA-VAL e-drive-34. User Manual. Motorised Pilots. CLA-VAL Europe LIN072UE - 04/16
User Manual CLA-VAL Europe www.cla-val.ch cla-val@cla-val.ch 1 - LIN072UE - 04/16 Table of Contents 1 Introduction... 3 1.1 Precautions Before Starting... 3 1.2 Troubleshooting... 3 1.3 General Disclaimer...
More information